Re200ge 140909

Download as pdf or txt
Download as pdf or txt
You are on page 1of 8

MESSRS.

:
AGENT

SPECIFICAION
OF
PYROELECTRIC PASSIVE
INFRARED SENSOR

MODEL NO.
PART NO.

RE200GE

C103 GSBC Bldg, 107 Gwanggyo-ro,Yeongtong-gu,


Suwon,Gyeonggi-do,SOUTH KOREA
DiYPRO CO.,LTD.
FresnelFactory by DiYPRO CP.,LTD.
KOREA - www.diypro.co.kr
ENGLISH - www.fresnelfactory.com
TEL : +82 70-7605-0693 FAX : +82 31-259-7500

APPROVED BY

MODEL NO. :

RE200GE
PART NO.

CHECKED BY

DRAWING NO.

DRAWN BY

REV PAGE

1/8

Scope
This specification describes a pyroelectric passive infrared sensor supplied by NIPPON
CERAMIC CO.,LTD.

Type of sensor
Balanced differential(series opposed type.)
Physical configuration
1) Package

: TO-5 metal can with dimensions shown in Figure 1-c


(Ni-plated)

2) Element geometry

: Two sensitive areas 2.3 mm long, 1.0 mm wide and


spaced 1.0 mm apart.

3) Element orientation

: See Figure 1-b

4) Lead configuration

: See Figure 1-c,1-d

5) Code
:
Lot number is marked on top surface of detector.
To show last one digit of the A.D. year and week of the year of a inspection completion
Nicera Identification code.
Example
Nicera Identification code
26th week
Year 2014

MODEL NO. :

DRAWING NO.

REV PAGE

RE200GE
PART NO.

2/8

Electrical characteristics (at 25 (+/-) degC)


1) Circuit configuration

: Three-terminal sensor with source follower


See Figure 2

2) Operating voltage

: 1 ~ 15 V dc (Rs: 470kohm)

3) Source voltage

: 0.3 ~ 1.4 V (Vd: 5V, Rs: 470kohm)

4) Signal output

: Min.

2.5 Vp-p

(Typ. 4.0 Vp-p)

Signal output is measured at chopper frequency of 1 Hz when connected to the


amplifier of gain 72.5 dB (at 1 Hz) and submitted to the emission of Infrared energy of
13 microW/cm2 from 420 K Black Body.
See Figure 3
5) Noise output

: Max. 250 mVp-p

(Typ. 90 mVp-p)

Noise output shall be measured for 20 seconds when connected to the amplifier
of gain 72.5 dB (at 1 Hz) and shut out from Infrared energy.
See Figure 3
6) Balance output

: Max. 15 %

Bo / |SA+SB| 0.15
Bo : Balance output
SA : Signal output on Element A
SB : Signal output on Element B
Balance output is measured at chopper frequency of 1 Hz when connected to the
amplifier of gain 72.5 dB (at 1 Hz) and submitted to the emission of Infrared energy of
13 microW/cm2 from 420 K Black Body.
See Figure 3
7) Frequency response

MODEL NO. :

: 0.3 Hz to 3.0 Hz / (+/-) 10 dB

DRAWING NO.

REV PAGE

RE200GE
PART NO.

3/8

Optical characteristics
1) Field of view

: 138 from center of element on axis X


: 125 from center of element on axis Y
: See Figure 1-a

2) Filter substrate

: Silicon

3) Cut on (5 %T ABS)

: 5 (+/-) 1 micron

4) Transmission

: 70 % average 8 to 13 micron

Environmental requirements
1) Operating temperature : -30 degC to +70 degC
2) Storage temperature

: -40 degC to +80 degC

3) Relative humidity

The sensor shall operate without increase in noise output when exposed to
90 ~ 95 % RH at 30 degC continuously.
4) Hermetic seal

The sensor shall be sealed to withstand a vacuum of 21.28 kPa.

RoHS compliance
This product conforms to the RoHS Directive in force at the date of issuance of this
Specification Sheet.

MODEL NO. :

DRAWING NO.

REV PAGE

RE200GE
PART NO.

4/8

Configuration (Figure 1)
Field of view
138

125

0
4.

WINDOW
ELEMENT

3.
2. 0
0

(Figure 1-a)

1
1

Top view
(Figure 1-b)

42
6B

Example of lot number

9.20.2
8.30.2

Side view
4.50.2

OPTICAL HEIGHT
ELEMENT HEIGHT

13.51.0

3.70.1
3.30.1

(Figure 1-c)

0.453

Base view
(Figure 1-d)

PCD 5.08
45

1: Drain
2: Source

3: Ground
unit : mm

MODEL NO. :

DRAWING NO.

REV PAGE

RE200GE
PART NO.

5/8

Circuit configuration (Figure 2)

VD:5V

1 DRAIN

+
-

(-)
(+)

(+)
(-)

+
-

2 SOURCE
RS:470K

3 GND

SENSOR

MEASUREMENT AMP.

RECORDER

Measurement Amp.: Non-inverted type, gain 72.5 dB at 1 Hz , 0.4 to 2.7 Hz-3 dB

Test set-up block diagram (Figure 3)

AMP .
REC OR DER

SEN SO R

HEA T SOU RC E
420 K BL AC K B ODY
APE RT URE 1 2m m

CHO PP ER

S HUT TER

:1Hz CHOPPING

(FOR NOISE MEASUREMENT)

OC CL UDE R

Occluder position

OCCLUDER

Signal output

MODEL NO. :

SHUTTER,CHOPPER

OCCLUDER

Balance output

DRAWING NO.

Noise output

REV PAGE

RE200GE
PART NO.

6/8

Notes
1.Design restrictions/precautions
If used for outdoor applications, be sure to apply suitable supplementary optical filter and
drip-proof, anti-dew construction. This sensor is designed for indoor use.
in cases where secondary accidents due to operation failure or malfunctions can be
anticipated, add a fail safe function to the design.
2.Usage restrictions/precautions
To prevent sensor malfunctions, operational failure or any deterioration of its characteristics,
do not use this sensor in the following, or similar, conditions.
a. In rapid environmental temperature changes.
b. In strong shock or vibration.
c. In a place where there are obstructing materials (glass,fog,etc.) Through
which Infrared rays cannot pass within detection area.
d. In fluid, corrosive gases and sea breeze.
e. Continual use in high humidity atmosphere.
f. Exposed to direct sun light or headlights of automobiles.
g. Exposed to direct wind from a heater or air conditioner.
3.Assembly restrictions/precautions
Soldering ______
a. Use soldering irons when soldering.
b. Avoid keeping pins of this sensor hot for a long time as excessive heat may
cause deterioration of its quality.(e.g. within 5 sec. at 350 degC)
Washing ______
a. Be sure to wash out all flux after soldering as remainder may cause malfunctions.
b. Use a brush when washing. Washing with an ultrasonic cleaner may cause operational
failure.

MODEL NO. :

DRAWING NO.

REV PAGE

RE200GE
PART NO.

7/8

4.Handling and storage restrictionsprecautions


To prevent sensor malfunctions, operational failure, appearance damage or any
deterioration of its characteristics, do not expose this sensor to the following or similar,
handling and storage conditions.
a. Vibration for a long time.
b. Strong shock.
c. Static electricity or strong electromagnetic waves.
d. High temperature and humidity for a long time.
e. Corrosive gases or sea breeze.
f. Dirty and dusty environments that may contaminate the optical window.

5.Restrictions on product use


The product described in this document shall not be used or embedded to any downstream
products of which manufacture, use and/or sales are prohibited under any applicable laws
and regulations.
Sensor troubles resulting from misuse, inappropriate handling or storage are not the
manufacturer's responsibility.

MODEL NO. :

DRAWING NO.

REV PAGE

RE200GE
PART NO.

8/8

You might also like