Scribd
Upload
121 views

Tutorial 6 PDF

This document provides a tutorial for conducting a finite element analysis in Abaqus CAE to model contact between two parts of an electrical switch. The tutorial describes 24 steps to create and mesh parts, define materials, apply boundary conditions including a displacement and contact interaction, submit a job, and visualize stress contours and contact pressure results. The goal is to investigate the contact region and stresses resulting from displacing the upper portion of the switch by a prescribed amount.

Uploaded by

florinelvv
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
121 views

Tutorial 6 PDF

This document provides a tutorial for conducting a finite element analysis in Abaqus CAE to model contact between two parts of an electrical switch. The tutorial describes 24 steps to create and mesh parts, define materials, apply boundary conditions including a displacement and contact interaction, submit a job, and visualize stress contours and contact pressure results. The goal is to investigate the contact region and stresses resulting from displacing the upper portion of the switch by a prescribed amount.

Uploaded by

florinelvv
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 17

ENGI 7706/7934: Finite Element Analysis

Abaqus CAE Tutorial 6: Contact


Problem
_________________________________________________________
Problem Description
In this problem, a segment of an electrical contact switch (steel) is modeled by
displacing the upper portion by a prescribed amount and investigating the resulting
contact region and stress.

Analysis Steps
1. Start Abaqus and choose to create a new model database
2. In the model tree double click on the Parts node (or right click on parts and select
Create)

3. In the Create Part dialog box (shown above) name the part and
a. Select 3D
b. Select Deformable
c. Select Shell
d. Select Extrusion
e. Set approximate size = 50
f. Click Continue
4. Create the geometry shown below (not discussed here).
a. Note: The right vertical edge of the switch does not need to be drawn.
b. Click Done
c. Set Depth = 2
d. Click OK

5. To aid in mesh refinement and assigning contact surfaces, we want to partition the lower
half of the switch.
a. In the toolbox area click on the Partition Face: Sketch icon.
b. Select the lower half of the switch and click Done
c. Select the right edge of the lower half of the switch.
d. In the toolbar, click on the Iso View icon.
i. Note: If the View toolbar is not visible go to the menu ViewToolbarsViews
e. In the toolbox area click on the Project Edges icon.
f. Select the highest edge of the top half of the switch as shown. Click Done twice.
g. Click Done to accept partition geometry.

6. Double click on the Materials node in the model tree


a. Name the new material and give it a description
b. Click on the Mechanical tabElasticityElastic
c. Define Youngs Modulus and the Poissons Ratio (use SI (mm) units)
d. Click OK

7. Double click on the Sections node in the model tree


a. Name the section ShellProperties and select Shell for the category and
Homogeneous for the type
b. Click Continue
c. Select the material created above (Steel) and set the thickness to 0.15
d. Click OK

8. Expand the Parts node in the model tree, expand the node of the part just created, and
double click on
Section Assignments
a. Select the entire geometry in the viewport and press Done in the prompt area
b. Select the section created above (ShellProperties)
c. Specify shell offset if necessary
d. Click OK

e. In the menu bar select Assign Element Normal


f. Select the lower half of the switch, click Done
g. The purple faces of the contact areas should now be facing each other.
i. Note: The geometry may start with the purple faces up, in which case you will have to flip
the orientation of the top surface. The end goal is that you have the purple faces of the two
contacting surfaces facing each other.

9. Expand the Assembly node in the model tree and then double click on Instances
a. Select Dependent for the instance type
b. Click OK

10. Double click on the Steps node in the model tree


a. Name the step, set the procedure to General, select Static, General, and click
Continue
b. Accept the default settings, click OK

11. Double click on the BCs node in the model tree


a. Name the boundary conditioned Fixed and select Symmetry/Antisymmetry/Encastre
for the type

b. Select the right edge of both halves of the switch and click Done
c. Select ENCASTRE for the boundary condition and click OK

12. Double click on the BCs node in the model tree


a. Name the boundary conditioned Disp and select Displacement/Rotation for the type
b. Select the top edge of the triangular portion of the geometry
c. Set the ydisplacement to 3, click OK

13. Double click on the Interaction Properties node in the model tree
a. Name the interaction properties and select Contact for the type, click Continue
b. On the Mechanical tab Select Tangential Behavior
i. Set the friction formulation to Frictionless
c. On the Mechanical tab Select Normal Behavior
i. Because the surfaces do not start in contact, change the constraint enforcement method
to Penalty
d. Click OK

14. Double click on the Interactions node in the model tree


a. Name the interaction, select Surfacetosurface contact, and click continue
b. For the master surface select the lower portion of the geometry at the free end and click
done

i. While applying the fixed displacement, the nodes at the tip of the upper portion of the
geometry will make contact at an unknown location on the lower surface
ii. Nodes on the slave surface cannot penetrate the surface formed by the element faces on
the
master surface
c. Select the color of the surface corresponding to the top surface
d. For the slave surface, set the slave type to Surface
e. Select the upper portion of the geometry at the free end and click done
f. Select the color of the surface corresponding to the bottom surface
g. Change the contact interaction properties to the one created above (if not already done)
h. Click OK

15. In the model tree double click on Mesh for the Switch part, and in the toolbox area
click on the Assign
Element Type icon
a. Select all of the geometry
b. Select Standard for element type
c. Select Linear for geometric order
d. Select Shell for family
e. Note that the name of the element (S4R) and its description are given below the element
controls
f. Select OK

16. In the toolbox area click on the Assign Mesh Controls icon
a. Select all of the geometry
b. Change the element shape to Quad
c. Change the technique to Structured

17. In the toolbox area click on the Seed Edges icon


a. Select the two fixed edges, click Done
b. Select By number
c. Set Bias to None
d. Under Sizing Controls enter 8 elements, Click OK

18. In the toolbox area ensure the Seed Edges icon is still selected
a. Select the edges indicated below
b. Set Method to By Size and Bias to Double
c. Set Minimum size to 0.25 and Maximum size to 1, click OK

19. In the toolbox area ensure the Seed Edges icon is still selected
a. Select the remaining edges indicated below
b. Set Method to By Size and Bias to None
c. Set Approximate element size to 0.25, click OK

20. In the toolbox area click on the Mesh Part icon


a. Click Yes

21. In the model tree double click on the Job node


a. Name the job switch
b. Give the job a description, click Continue
c. Accept defaults, click OK

22. In the model tree right click on the submitted and successfully completed job, and select
Results

23. Display the deformed contour of the (Von) Mises stress overlaid with the undeformed
geometry
a. In the toolbox area click on the following icons
i. Plot Contours on Deformed Shape
ii. Allow Multiple Plot States
iii. Plot Undeformed Shape

24. In the toolbox area click on the Common Plot Options icon
a. Set the Deformation Scale Factor to 1
b. Click OK

25. To change the output being displayed, in the menu bar click on ResultsField Output
a. Select the contact pressure at surface nodes (CPRESS)
b. Click OK

You might also like