Scribd
Upload
163 views

Engineering Note NTC and PTC Thermistors: Vishay Dale

Thermistors are temperature sensitive resistors that change resistance predictably with temperature. There are two main types: NTC thermistors decrease in resistance as temperature increases, while PTC thermistors increase in resistance with rising temperature. A linear PTC thermistor was recently developed that has a linear resistance-temperature relationship. Thermistors can be used for temperature measurement, control, and compensation in various applications.

Uploaded by

Diablo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
163 views

Engineering Note NTC and PTC Thermistors: Vishay Dale

Thermistors are temperature sensitive resistors that change resistance predictably with temperature. There are two main types: NTC thermistors decrease in resistance as temperature increases, while PTC thermistors increase in resistance with rising temperature. A linear PTC thermistor was recently developed that has a linear resistance-temperature relationship. Thermistors can be used for temperature measurement, control, and compensation in various applications.

Uploaded by

Diablo
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Engineering Note

Vishay Dale

NTC and PTC Thermistors


Linear PTC

Thermistors are temperature sensitive resistors that have a


greater than normal change in resistance value when the
temperature changes. The change in resistance is predictable
with changes in temperature. The extreme sensitivity to
temperature change enables a thermistor to perform many
functions and is utilized in an increasing variety of thermal
sensing/control applications.
The two basic types of thermistors generally available today
are the NTC and the PTC types. The NTC thermistors are
ceramic semiconductors that have a high Negative
Temperature Coefficient of resistance. NTC thermistors
decrease in resistance as the temperature increases. PTC
thermistors are Positive Temperature Coefficient resistors
generally made of polycrystalline ceramic materials that have
a high positive temperature coefficient, which increases in
resistance as the temperature increases.
Typically, NTC or PTC thermistors do not increase or decrease
in resistance with temperature in a linear fashion. The tables
below show several examples of nonlinear resistancetemperature curves. Developed recently was a Vishay Dale
linear PTC thermistor that has a linear resistance temperature
relationship.
Typical NTC R-T Curve

Resistance Ohms

INTRODUCTION
225
200
175
150
125
100
75
50
25
0
- 50 - 25

25

50

75

100 125 150

Temperature C

NTC THERMISTORS
NTC thermistors are composed of sintered metal oxides such
as manganese, nickel, cobalt, iron, copper and aluminum.
The exact shape of the finished product such as disc or chip
is dictated by the specific applications. The most prevalent
configurations are discs and chips both leaded and surface
mount varieties.
Generally, the larger disc style thermistor functions
in the self-heating mode; that is, the change in resistance is
a result of the wattage (heat developed by the passage of a
relatively large current through the device). The smaller chip
style NTC thermistor generally changes body temperature/
resistance by absorbing the surrounding or ambient
temperature.

NTC (-1 %/C)

7
6
5
4
3
2
- 50

50

100

150

Temperature C
Typical PTC Curve
1,000,000
100,000
10,000
1000
100
10
2
1
0.1

100C Switching
Temp. Curve
0

15

30

60

90

105 120 135 150

165

NTC THERMISTOR APPLICATIONS


Temperature Measurement
The high sensitivity of a thermistor makes it an ideal candidate
for low cost temperature measurement applications.

Temperature C

Document Number 33016


Revision 07-Mar-02

For technical questions, contact [email protected]

www.vishay.com
3

Engineering Note
Vishay Dale

NTC and PTC Thermistors

Temperature Control
NTC thermistors can be used for temperature control (off/on)
using a minimum amount of circuitry.

The linear relationship between temperature and resistance


simplifies the designers task in that the characteristic nonlinear curve needs no normalization.

Temperature Compensation
In many cases, circuit precision requires that there is some
sort of temperature compensation. Oscillators, LCD displays,
a battery under charge and some amplifiers are examples of
circuits that may require temperature compensation.

THERMISTOR ASSEMBLIES

Inrush Current Limiter


An NTC disc thermistor subjected to a change in power will
experience a time lag before reaching a lower resistance.
This time lag can be utilized to limit the inrush surge current
(the larger the part, the greater the lag).

Thermistor assembly probes are available in a wide variety


of configurations. The choice of assembly mounting, housing,
etc., is dependent on the application. Primary factors that
determine configuration of a thermistor assembly is operating
environment, method of mounting and thermal time response.
For specialized applications Vishay Dale offers a custom
design service which allows the customer to advance from
conception to design, manufacture and installation. Typical
thermistor assemblies are shown below.

Fluid Level Applications


The thermistor can be used to sense the presence or absence
of a liquid by using the difference in dissipation constants
between a liquid and a gas.

PTC THERMISTORS
The PTC thermistor is generally a polycrystalline ceramic
material composed of oxyalate or carbonate with added
dopant materials. The PTC thermistor exhibits only a slight
change of resistance with temperature until the switching
point is reached at which point an increase of several orders
of magnitude in resistance occurs.

PTC THERMISTOR APPLICATIONS


Overcurrent Protection
When a fault condition occurs, the PTC thermistor will heat
up causing it to switch from a low to a very high resistance.
Electronic Ballast Design
PTC thermistors are used in electronic ballast systems as a
time delay element when the circuit is energized.
Motor Starting
With a PTC thermistor in series with the starting windings in a
single phase electronic motor, the PTC acts as a time delay.
Battery Management
As a rechargeable battery becomes fully charged, its
temperature increases and the PTC resistance increases
rapidly reducing the charge to a very low level.
Linear PTC Thermistor
The relatively recent development of the linear PTC
thermistor utilizes a thick film technology similar to the thick
film resistor.

www.vishay.com
4

Thermistor
A thermally sensitive resistor in which its primary function is
to exhibit a change in electrical resistance with a change in
body temperature.
Standard Reference Temperature
The thermistor body temperature at which nominal zero-power
resistance is specified (25C).
Zero-Power Resistance
This is the DC resistance value of a thermistor measured at a
specified temperature with a power dissipation by the thermistor
low enough that any further decrease in power will result in not
more than 1.0 percent (or 1/10 of the specified measurement
tolerance, whichever is smaller) change in resistance.
Resistance Ratio Characteristic
This identifies the ratio of the zero-power resistance of a thermistor
measured at 25C to that resistance measured at 125C.
Negative Temperature Coefficient (NTC)
An NTC thermistor is one whose zero-power resistance
decreases with an increase in temperature.
Positive Temperature Coefficient (PTC)
A PTC thermistor is one in which the zero-power resistance
increases with an increase in temperature.

For technical questions, contact [email protected]

Document Number 33016


Revision 07-Mar-02

Engineering Note
Vishay Dale

NTC and PTC Thermistors


Maximum Operating Temperature
The maximum body temperature at which the thermistor will
operate for an extended period of time with acceptable
stability of its characteristics. This temperature is the result
of internal heating, external heating, or both, and should not
exceed the maximum value specified.
Maximum Power Rating
The maximum power which a thermistor will dissipate for an
extended period of time with acceptable stability of its
characteristics.
Dissipation Constant (D.C.)
The ratio, in milliwatts per degree C, at a specified ambient
temperature of a change in power dissipation in a thermistor
to the resultant body temperature change.

Temperature Coefficient of Resistance (alpha, )


The temperature coefficient of resistance is the ratio
at a specified temperature, T, of the rate of change of zeropower resistance with temperature to the zero-power
resistance of the thermistor. The temperature coefficient is
commonly expressed in percent per degree C (%/C).
T = (dRt)
(dt)

Ambient Operating Temperature


The temperature of the air surrounding an object, neglecting
small localized variations.
Transition Temperature
The temperature at which the resistance of the PTC thermistor
begins to rise sharply.

Thermal Time Constant (T.C.)


The time required for a thermistor to change 63.2% of the
total difference between its initial and final body temperature
when subjected to a step function change in temperature
under zero-power conditions. This is normally expressed in
seconds.

Material Constant (Beta )


The material constant of an NTC thermistor is a measure of
its resistance at one temperature compared to its resistance
at a different temperature. Its value may be calculated by the
formula shown below and is expressed in degrees Kelvin (K).
The reference temperatures used in this formula for
determining material constant ratings of RT1 thermistors are
298.15K and 348.15K.

Resistance-Temperature Characteristic
The relationship between the zero-power resistance of a
thermistor and its body temperature.

= In (R @ T2/R @ T1) / (T21 - T1-1)

Stability
The ability of a thermistor to retain specified characteristics
after being subjected to designated environmental or
electrical test conditions.
Base Resistance (Ro)
The resistance value of a thermistor at a specified
temperature with negligible electrical power to avoid self
heating. Usually base resistance will be defined at 25C.
R @ Imax
Approximate resistance at maximum steady state current.
Switch Temperature (Tsw)
The temperature when the resistance of the PTC thermistor
reaches two (2) times the base resistance, sometimes
referred to as curie point or transition temperature.

Document Number 33016


Revision 07-Mar-02

Maximum steady-state current (Imax)


The maximum steady-state current is the rating of the
maximum current, normally expressed in amperes (A),
allowable to be conducted by an inrush limiting NTC thermistor
for an extended period of time.
Maximum Operating Voltage (Vmax)
The maximum rated voltage the thermistor can continuously
withstand 60 cycle AC or DC.
Maximum Continuous Current (Imcc)
The maximum amount of current which a PTC thermistor must
be able to pass without switching into its high resistance state.
Expressed in Amps.
Minimum Switching Current (Imsc)
The minimum amount of current necessary to switch the
thermistor into its high resistance state. Expressed in Amps.

For technical questions, contact [email protected]

www.vishay.com
5

You might also like