MV electrical network management

Easergy range

Flair 23DM
Communicating fault passage indicators
For all neutral arrangement system
Voltage detection relay

Modbus communication
Appendix to the user's manual

Flair 23DM

Summary

PRESENTATION ................................................................................................................................
................................
......................................... 3

COMMISSIONING AND DIAGNOSIS ................................................................................................

......................................... 5
2.1 AUTOMATIC ADAPTATION OF THE CONFIGURATION: AUTO-MODE ................................................................
...................................... 6
2.2 ACCESS TO DATA ................................................................................................................................
................................
........................................... 7
2.3 LIST OF ADDRESS ZONES ................................................................................................
................................
............................................................... 8
2.4 DATA CODING ................................................................................................................................
................................
................................................ 9
2.5 SYNCHRONIZATION, IDENTIFICATION ZONE................................................................................................
.....................................10
2.6 READING OF FLAIR 23DM IDENTIFICAT
NTIFICATION ................................................................................................
....................................12
2.7 MEASUREMENT AND COUNTERS
ERS ZONE ................................................................................................
...........................................14
2.8 REMOTE CONTROL ZONE ................................................................................................
................................
.............................................................16
2.9 REMOTE CONTROL ORDER AND STATUS
T
ZONE ................................................................
..............................................................18
2.10 TIME-TAGGED EVENTS ................................................................................................
................................
.............................................................20
2.11 ACCESS TO REMOTE SETTINGS ................................................................................................
.................................................24
2.12 DATE AND TIME-SETTING AND SYNCHRONIZATION ................................................................
.....................................................27
2.13 MANAGING THE DATE AND TIME USING FUNCTION 43 ................................................................
................................................29

NT00337-EN-01

Presentation

Flair 23DM

1 Presentation
The Flair 23DM has a communication
on port.
Modbus communication allows Flair 23DM relays to be connected to a supervisor or any other device with a master
Modbus communication port.
Flair 23DM is always the slave.

Accessible data:
Modbus communication can be used
sed to perform functions remotely such as:

Reading of measurements, counters and diagnosis

Reading of status conditions and remote indications

Transfer of time-tagged events

Reading of Flair 23DM identification

Time-setting and synchronization

Reading of settings

Remote settings when these have been enabled

Transmission of remote controls

Modbus protocol principle:

The Modbus protocol is used to exchange
exchan data by means of a request-response
se type mechanism
mec
between one
station called the master and N slavess. Exchange initialization (sending the request) iss always
a
initiated by the
master. The slave (Flair 23DM) can only respond to a request sent to it. When the network
rk hardware
h
infrastructure
allows, several slaves can be connected
nected to the same master. The request contains a sllave number (address) to
identify which is the destination. This number
numb must be unique. Slaves that are not destinations
destin
ignore the request
received.

Modbus Frame structure:

Each exchanged frame consists of a maximum of 255 bytes divided as follows (any frame with an error in format,
parity, CRC 16, etc. is ignored):
Slave Number
1 byte
Request destination
0: broadcast
(all)
1...247 (unique)

Function
Code
1 byte
Refer to the
next section

Data or Sub-Function Code

Da
n bytes
Requ
Request
or response data
(addr
addresses/bit or word values, number
of bits/bytes/data words)
Sub
Sub-function
code

Control Word
W
2 bytes
CRC 16 (for
( detection
of transm
mission
errors)

The first two fields in the response

se are usually
usua identical to those in the request.

Modbus Functions Supported

The Flair 23DM Modbus protocol is a subset of the Modbus RTU protocol:
protocol

Data exchange functions

o 1: read n output bits
o 2: read n input bits
o 3: read n output words
o 4: read n input words
o 5: write 1 bit
o 6: write 1 word
o 15: write n bits
rds
o 16: write n consecutive words

NT00337-EN-01

Presentation

Flair 23DM

Communication management functions

o 8: read Modbus diagnosis
osis counters
c
o 11: read Modbus event co
ounter
o 43 with sub-function 14: re
ead identification
o 43 with sub-function 15: re
ead date and time
o 43 with sub-function 16: write
w
date and time

Protocol for managing time-tagged

tagged events

Protocol for managing date and time synchronization

Broadcast commands are necessarily write commands. No reply is transmitted by the slaves.
slaves

Structure of Exception Frames

An exception frame sent by the destination Flair 23DM for the request consists of the following fields:
fields
Slave Number
1 byte
Request
destination

Exception Function
tion
Code
1 byte
Request function code
co
+128 (80h)

Exception Code

Contr
trol Word

1 byte
Possible codes
 1: unknown function code
 2: incorrect address
 3: incorrect data

2 bytes
CRC 16 (for detection
of transmission
nsmission errors)

Turnaround time
The response time Tr is the time between the end of receipt of a request and sending the
response:

Note: Tr includes the silence between 2 frames and is usually expressed for a format of 8 bits,
odd parity, 1 stop bit, at 9,600 Bauds.
The Flair 23DM response time is less than 10 ms (for
for all the speeds supported).
supported

Synchronizing Exchanges
Any character received
ceived after a silence lasting more than 3.5 characters is deemed to be
the start of a fram
me.
A minimum silence
lence with more than 3.5 characters must always
lways be kept
between 2 frames.
At 38400 bauds, this silence time is equal to 1,75 ms.
A slave ignores any
a frame:
received with a physical error on one or more characters (format, parity error, etc.)
with an invalid
d CRC 16
which is nott addressed
a
to it

NT00337-EN-01

Commissioning and diagnosis

Flair 23DM

2 Commissioning and diagnosis

Modbus protocol parameters
Parameters Designation
on HMI
Cubn
Cubicle number

Addr

Modbus address
Modbus

bAUd

Baud rate

Authorized values

Display
on HMI
0 (the
the Modbus address is configurable manually
manually) nonE
129 (the Modbus address is proposed
automatically depending to the cubicle number
129
defined)

1...247 (the Modbus address, configured

automatically from the Cubicle number value, is
defined as follow: @ = 33+ 5x(CubicleNb-1).
The Modbus address can be changed manually,
manually if the
one proposed automatically is not appropriate.
In this case, modification of the address changes
automatically the Cubicle number to 0.
Auto-mode (*)
1200 Baud
2400 Baud
4800 Baud
9600 Baud
19200 Baud
38400 Baud

Default
value
0

1247

247

Auto-mode

Prty

Parity (hidden
parameter if Auto-mode activated

None (1 stop bit)

Even (1 stop bit)
Odd (1 stop bit)

Auto
1.2
2.4
4.8
9.6
19.2
38.4
None
EUEn
Odd

rCnF

Remote
control

OFF : Remote settings not enabled

ON : Remote settings enabled

OFF
On

ON

SbO

Selection before
execution

OFF
On

OFF

OFF : Remote control in direct mode

ON : Remote control in SBO mode (Selection
Before Execution)

Even

(*): The Auto-Mode

Mode supports only the values highlighted in gray in the table.

Link activity LED

The Orange LED on the upper and left part of the RJ45 connector is activated when a trafic is
detected on the Modbus port.
port (blinking: 200ms ON / 800 ms OFF)
Note: the second LED on the upper and right part of the RJ45 connector is not used.
used

NT00337-EN-01

Auto-adaptation
adaptation of the configuration

Flair 23DM

Modbus Link Diagnosis

To check thatt the link
li is operating correctly, the user can refer to:
1. the link activity
tivity LED, on the RJ45 connector of Modbus RS485 link
2. the Modbus diag
iagnosis counters and the Modbus event counter

2.1 Automatic Adaptation

daptation of the Configuration: Auto-mode
mode
Presentation
The "Auto-mode"
mode" mechanism is a device for simplifying the Modbus
bus device configuration. Its
algorithm allows
llows a Flair 23DM (slave) to automatically detect the configuration
config
used on the
Modbus link to which it is connected.
co
Operation
The algorithm in
n the
t "Auto-mode" mechanism automatically detects the network parameters
by testing the ava
ailable transmission speeds and parities. The Modbus master must send at
least 13 frames on the Modbus
Mod
network before the "Auto-mode" mechanism
mech
algorithm works.
There must be en
nough traffic on the link before the Flair 23DM can be deemed to be absent or
in faulty status.
The detection of network parameters begins firstly at maximum speed (38400 baud). Then, if
detection is not conclusive,
conclusive detection continues with the next lower speed (e.g.
(e 19200 baud)
and so on in order to detect the suitable speed.
The detected network parameters are deemed to be valid after correct reception of three
different frames. In this case, the product will use the detected parameters and will save
them in non-volatile
volatile memory.
Note: If the Modbus
dbus configuration
confi
set on the Flair 23DM is modified
dified manually
ma
by the installer
to fix the speed to a specific value,
value the "Auto-mode" mechanism will
w be disabled. The
automatic search of network parameters will be only active again if Auto-mode
Auto
is reactivated manually.
manually
Note: On restarting
starting the Flair 23DM, the saved Modbus parameters
rs on the product will be
memorised. In the event
ev
of a fault on restarting, the search phase
hase will
wi be disabled.
The
he research phase is restarted from the last speed memorised by the Auto-mode
Auto
and it will
validates again this speed if 7 valid frames are detected at that speed. Thereafter, the
research phase is restarted after 7 successive faults detected during operation.
Moreover itt is possible
possi
to disable the "Auto-mode" mechanism and
d then manually set the
Modbus
us network parameters
Detectable Configurations
The 3 configurations
ons supported
sup
by the algorithm are as follows:
Even parity, 1 stop bit
Odd parity, 1 stop bit
no parity, 1 stop
op bit
associated with th
he following 3 transmission speeds:
9,600 Baud
19,200 Baud
38,400 Baud
i.e. a total of 9 dettectable configurations.
Note: It is recommended to avoid the format "no parity". When operating on a network "no
parity", the Flair23DM select the format "no parity, 1 stop bit" whatever the number of stop bits
used by the Master.

NT00337-EN-01

Access to data

Flair 23DM

2.2 Access to data

Addressing a word
All Flair 23DM data that can be accessed by Modbus communication is organized
org
into 16-bit words.
Each word is identiified by its address, coded on 16 bits, i.e. from 0 to 655
535 (FFFFh).

Addressing a bit
Some data can also
a
be accessed in the form of a bit. The bit address
ddress is then
t
deducted from
the word address
dress by:
Bit address = (word address x 16) + bit number (0...15).
Example:
Address word 3072 (0C00h)
(
bit 0 address = C000h
bit 14 address = C00Eh
Undefined Addresses
d
in this document should be used. If other addresses
ad
are used, the
Only addresses defined
Flair 23DM can either respond with an exception message, or provide
rovide non-significant data.
Access mode
ect-access: they are permanently identified
entified by their Modbus
Mod
address.
The data are dire
These can
n be reached
reach in a single read or write operation, applying
ying to all or part of the
relevant zone.
In Flair 23DM, all zones are accessed directly, however for some zones,
z
such as those for
time-tagged even
nts, a particular protocol can be used to optimize exchanges
exchan
with the
supervisor. This protocol
p
is specified in the relevant zones.

NT00337-EN-01

Flair 23DM

List of address zones

2.3 List of Address zones

The accessible registers of Flair 23DM that can be read through the communication are grouped in the following
table:
Address zones

Time synchronization zone

Synchronization zone
Identification zone
Identification data
Remote control zone
TCS
Remote informations zone
TSS
Remote metering zone
TM
Counters zone
CNT
Network management zone
Network management
Remote settings zone
Remote setting zone #1
Remote setting zone #2
Remote setting zone #3
Event table zone
Event table

Word Address
Range
(Hexadecimal)
0002h to 0005h
0002h to 0005h
0006h to 003Fh
0006h to 003Fh
00F0h to 00F5h
00F0h to 00F3h
0100h to 0103h
0100h to 0103h
0400h to 040Dh
0400h to 040Dh
0500h to 050Dh
0500h to 050Dh
0A20h to 0A2Fh
0A20h to 0A2Fh
1E00h to 1E2Fh
1E00h to 1E12h
1E20h to 1E27h
1E28h to 1E2Fh
E000h to E4B1h
E000h to E4B1h

Word Address
Range
(Decimal)
2 to 5
2 to 5
6 to 63
6 to 63
240 to 245
240 to 245
256 to 259
256 to 259
1024 to 1037
1024 to 1037
1280 to 1293
1280 to 1293
2592 to 2606
2592 to 2606
7680 to 7727
7680 to 7698
7712 to 7719
7720 to 7727
57344 to 58545
57344 to 58545

Length
(word16)
4
4
58
58
6
4
2
2
14
14
14
14
16
16
34
18
8
8
1202
1202

Access
Mode

Access
Type

Direct

Word

Direct

Word

Direct

Word / Bit

Direct

Word / Bit

Direct

Word

Direct

Word

Direct
Direct
Direct

Word
Word
Word

indirect

Word

Note : the address zones not mentioned in this table are reserved addresses.

NT00337-EN-01

Data coding

Flair 23DM

2.4 Data coding

Format used
Apart from exceptions
ons mentioned
m
in the text, Flair 23DM data is coded
ded in one of the formats
below:
32S: signed
ed value,
valu coded on 32 bits
16S: signed
ed value,
valu coded on 16 bits
B: bit or set of bits
ASCII nc: string of n characters in ASCII code
IEC: time codin
ng format on 4 words conforming to IEC 60870-5-4.
32S Format
Flair 2xD does not support 32-bit
32 bit measurements. This format is only valid for the counters.
In 32S format, the first word is the most significant.
An incalculable value,
ue, whether invalid or outside the authorized range,
ge, is fixed at 2147483648
(80000000h).
16S Format
An incalculable value,
ue, whether invalid or outside the authorized range,
ge, is fixed at 32768
(8000h).
ASCII Format
ASCII format is used to code the identification strings for a Flair 23DM.
23DM
When the ASCII strings do not fill up the field entirely, they are completed with null bytes.
The first character occupies the most significant byte on the first word, the second the least
significant byte on the first word, etc.
etc

IEC Format
The date and time are coded on 4 words, in IEC 60870-5-4 format (bits
its at 0 in the table are not
used: they are always
ways read
r
at 0 and ignored in write mode):
Bit
15 14 13 12 11 10 9
8
7
6
5
4
3
2
1
0
Word Reserved (0 in read mode, variable in write mode) 0
Year (0...99
9)
1
Word 0
0
0
0
Month (1...12)
0
0
0
Day (1...31)
2
Word 0
0
0
Hour (0...23)
0
0
Minute
es (0...59)
3
Word Milliseconds
onds (0...59,999)
4
Year - 1 byte for years: varies from 0 to 127 years. (1/1/2000 to 31/12/2127).
Month - (4 bits) for months: varies from 1 to 12.
Day Day of Month, (5 bits): varies from 1 to 31.
Hour - 1 byte for hours: varies from 0 to 23.
Minute - 1 byte for minutes: varies from 0 to 59.
Millisecond - 2 bytes for milliseconds: varies from 0 to 59999.

NT00337-EN-01

Synchronization, identification zone

Flair 23DM

2.5 Synchronization,, identification zone

Introduction
Synchronization, identification, metering, network diagnosis and test zones are accessed
directly and do not contain any events.
For each zone, a table contains the following information:
description of the addresses in the zone
codes
es for Modbus functions that can be used in read mode
codes for Modbus functions that can be used in write mode
if necessary, the formats and resolution of the stored data

Synchronization zone
The synchronizati
nization zone contains the 4 words used to code the ab
bsolute time required for
time-tagging even
nts:
Description
Binary time (year)
Binary time (month + day)
Binary time (hours + minutes)
Binary time (milliseconds)

Address
2 (0002h)
3 (0003h)
4 (0004h)
5 (0005h)

Read
3
3
3
3

Write
16
16
16
16

Format
IEC

Note: The write operation should be performed on the whole zone and uses start
address 0002 with a length of 4 words.
words

Year (0 to 99)

b15

b8
0

b15

b0

Month (1 to 12)

b15

0
b8

b7

b7

Hour (0 to 23)

b0
0

b8

Day (1 to 31)

minute (0 to 59)

b7

b0

Milliseconds (0 to 59999)
b15

10

b8

b7

b0

NT00337-EN-01

Synchronization, identification zone

Flair 23DM

Identification zone
The identification
on label
la
contains:
10 words, used to code the serial number on a Flair 23DM unitit
1 word for the cubicle
cu
number
1 word for the product type
48 to encode
e the basic identification of Flair 23DM.

Description
Serial Number

Adress
Read
25982607
3
(0A26h...0A2Fh)

Write

Format
rmat Value
ASCII
(see after)

Cubicle_Number

14 (000Eh)

16S

Device_Type
Device Identification

15 (000Fh)
1663
(0010h...003Fh)

3
3

16S
ASCII

1 to 29
0 means not used
1 = Fault detector
Basic identification

Serial number :
The Flair 23DM provides a specific product coding (serial number) on 17 characters, within a 10
registers area:

1216066406
0664060010001
OOOOOO : Order
number

YYWW : Order Year/Week

LLL : Order Line Nb

SSSS : Seq Number within order line

Le numro de srie est cod comme suit :

Bit

Mot


Bit

15
Word


2598

0A26h

2599
2600

14

13

12

11

10

Order Year (First ASCII character "0" .."9")

Order Year (Second ASCII

A
character "0" .. "9")

0A27h

Order Week (First ASCII character "0" .. "5")

Order Week (Second ASCII character "0" .. "9")

0A28h

Order Number (First ASCII character "0" .."9")

Order Number (Second ASCII character "0" .. "9")

2601

0A29h

Order Number (Third ASCII character "0" .."9")

Order Number (Fourth ASCII character "0" .. "9")

2602

0A2Ah

Order Number (Fifth ASCII character "0" .."9")

Order Number (Sixth ASCII character "0" .. "9")

2603

0A2Bh

OrderLineNb (First ASCII character "0" .. "9")

OrderLineNb (Second ASCII character "0" .. "9")

2604

0A2Ch

OrderLineNb (Third ASCII character "0" .. "9")

SeqNbinLine (First ASCII character "0" .. "9")

2605

0A2Dh

SeqNbinLine (First ASCII character "0" .. "9")

SeqNbinLine (Second ASCII character "0" .. "9")

2606

0A2Eh

SeqNbinLine (Third ASCII character "0" .. "9")

Reserved (NULL=0)

2607

0A2Fh

Reserved (NULL =0)

Reserved (NULL=0)

dentification:
Product identification:
(see
see the corresponding chapter)
chapter

NT00337-EN-01

11

Reading of Flair 23DM identification

Flair 23DM

2.6 Reading of Flair 23DM identification

i
Introduction
The Read Device
ce Identification
I
function can be used for standard access to the information
required for identificcation of a device.
The description be
elow is a subset of the function options, adapted
pted to the example of Flair
23DM.
The main identification data are also accessible by direct reading of registers at the addresses
below.
Note: Data of Group 2A are not accessible by direct reading.
Identification du Flair 23DM
entification consists of strings of ASCII characters called
c
objects.
The Flair 23DM ide
The Flair 23DM objects are divided in three groups:
Group
1
Basic

Nb Object
0h VendorName
1h
2h

2A
Regular

3h
4h
5h

Value
Schneider Electric

Lenght
enght
Adress
Read
18 (12h) 1624
3
(0010h..0018h)

ProductCode
(EAN13)3 60648 05158 42 20 (14h)
(reference coded in EAN13 format)
MajorMinorRevision
xxx.yyy
7
(application version number)
numbe
(i.e.: 001.004)
VendorURL
ProductName
ModelName (short iden
dentification
code)

25...34
(0019h..0022h)
3538
(0023h..0026h)

www.schneider-electric.com 26 (1Ah)
FLAIR Serie 20
14
FLAIR23DM
8

6h UserApplicationName
Exploitation
3
80h FirmwareSubRevision number (last zzz
Extended
(i.e.: 000)
field of the application version
number)

3
3
3
3

12 (0Ch)
3
3940
(0027h..0028h)

3
3

81h PPID MajorMinorRevisi

Revision
(communication
communication protocol version)

xxx.yyy
(i.e.: 000.002)

25922595
3
(0A20h..0A23h)

82h PPID SubRevision number

mber (last
field of the communication
protocol version number)
number

zzz
(i.e.: 000)

25962597
3
(0A24h..0A25h)

83h Serial number

Refer to the identification

zone that describes the
serial number format.
Note: PPID = Product Protocole Interface Description.

17 (11h)
(1
25982607
3
(0A26h..0A2Fh)

ProductCode
The EAN13 code id
dentifies the reference for a Flair 23DM universally
lly in 13 digits:
d
Standards Organizati
nization Manufacturer Reference Checksum
3
12

60648

05158

42
NT00337-EN-01

Reading of Flair 23DM identification

Flair 23DM

Request frame
The read identification request frame consists of the following fields:
fields:
Field
Slave number
Function code
MEI type (sub-function
function code)
Read type
Not used
CRC16

Size (Bytes)
1
1
1
1
1
2

Value
1...247
43 (2Bh)
14 (0Eh)
01 or 02 or 03 or 04
00
Calculated

Response frame
The response frame consists of the following fields:
fields
Field
Slave number
Function code
MEI type (sub-function
function code)
Read type
Conformity level
Not used
Not used
Number of objects
First object number
First object length
First object ASCII string
...
nth object number
nth object length
nth object ASCII string
CRC16

Size (Bytes)
1
1
1
1
1
1
1
1
1
1
lg1
...
1
1
lgn
2

Value
1...247
43 (2Bh)
14 (0Eh)
01 or 02 or 03 or 04
131 (83h)
00
00
n = 3, 7 or 11, according to the Read type field
obj1
lg1
txt1
...
objn
lgn
txtn
Calculated

Exception frame
If an errorr occurs while
wh processing the request, the Flair 23DM sends
nds an exception
exce
frame,
consisting off the following fields:

NT00337-EN-01

Field
Slave number
Function code increased by 80h
MEI type (sub-function
function code)

Size (Bytes)
1
1
1

Value
1...247
171 (ABh)
14 (0Eh) or other if MEI type received is
incorrect.

Exception code

CRC16

01: MEI type received

receiv is incorrect( 14).
02: in cases of individual access (read code
04), if the requested
sted object does not exist.
03: incorrect data (frame
(
length incorrect or
read code invalid).
Calculated
13

Measurement and counters zone

Flair 23DM

2.7 Measurement and counters zone

Measurement zone
Description

Address Address Read

Decimal Hexa.

Writte

Fo
ormat Unit

Range

Phase current I1
Phase current I2
Phase current I3
Residual current Io
Maximeter phase current IM1
Maximeter phase current IM2
Maximeter phase current IM3
% nominal voltage phase V1
% nominal voltage phase V2
% nominal voltage phase V3
% nominal voltage residual V0
% nominal voltage phase U12
% nominal voltage phase U13
% nominal voltage phase U23
Note: all the TM are read only.
only

1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037

16S
16S
16S
16S
16S
16S
16S
16S
16S
16S
16S
16S
16S
16S

0-800 A
0-800 A
0-800 A
0-800 A
0-800 A
0-800 A
0-800 A
0-1000%
0-1000%
0-1000%
0-1000%
0-1000%
0-1000%
0-1000%

0400h
0401h
0402h
0403h
0404h
0405h
0406h
0407h
0408h
0409h
040Ah
040Bh
040Ch
040Dh

3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4
3, 4

1A
1A
1A
1A
1A
1A
1A
1%
1%
1%
1%
1%
1%
1%

Counters zone
Description

Address
Hexadecimal
0500h to 0501h

Read

Writte

Format

Phase + Earth Fault counter

Address
Decimal
1280 to 1281

R/P

32S

Phase Fault counter

1282 to 1283

0502h to 0503h

R/P

32S

Earth Fault counter

1284 to 1285

0504h to 0505h

R/P

32S

Transient Phase Fault counter 1286 to 1287

0506h to 0507h

R/P

32S

Transient Earth Fault counter

1288 to 1289

0508h to 0509h

R/P

32S

Voltage Presence Loss

counter
Transient Voltage Presence
Loss counter

1290 to 1291

050Ah to 050Bh

R/P

32S

Confirmed fault
passages
Confirmed fault
passages
Confirmed fault
passages
Unconfirmed fault
passages
Unconfirmed fault
passages
Relay1

1292 to 1293

050Ch to 050Dh

R/P

32S

Relay1. Duration
shorter than
minimal duration
(T12)

Note: R/P = Read/Preset

14

NT00337-EN-01

Measurement and counters zone

Flair 23DM
Counters for Modbus diagnosis

The diagnosis counters are read using function 8 and sub-codes

sub codes 000Bh to 0012h depending
on the counter.
Function 8 can also be used in echo mode (sub-code
(sub
0000h):
Function
8 in echo mode

Frame Sent
01 08 0000 1234 ED7C

Frame Expected in Response

01 08 0000 1234 ED7C

Event counter is read using function 11.

Also accessible as manufacturer data by direct register access:
access
Description
Reset counters
Bus Message Count
Bus Communication Error Count
Slave Exception Error Count
Slave Message Count
Slave No Response Count
Idle count

Address
62464 (F400h)
62465 (F401h)
62466 (F402h)
62467 (F403h)
62468 (F404h)
62469 (F405h)
62470 (F406h)

Read
3
3
3
3
3
3

Write
6, 16

Format
1 = reset

If no
activity >
80ms

May be displayed
ayed also locally on the product by the following operation:
- 5s press on ESC button => the Flair 23DM displays "Fact",
", blinking
- press left button "
"
"
within 3s (if not will the product will be reseted)
reseted
- navigate to reach "CPT" menu
- use the "
" button to freeze/unfreeze circular display of counter values
- use Test/Reset button during counter display to reset them (other
(
Reset can be done via
communication or general reset of product
Resetting counters
The counters are reset to 0 in the following cases:
when they reach the maximum value 65535 (FFFFh)
when they are reset by a Modbus command (function 8, subcode 000Ah)
000Ah
during a power failure of Flair 23DM.

NT00337-EN-01

15

Remote control zone

Flair 23DM

2.8 Remote Control

ontrol zone
Introduction
Remote control orders are transmitted to the Flair 23DM via pulse type remote control orders
using one of the following two modes, chosen via the settings:
Direct mode
Confirmed SBO (Select Before Operate) Mode.
Mode
Remote Control zone
co
The remote control zone contains:
Description
Single remote control orders (TCS)

Word adresses Read

240
1, 2, 3, 4
(00F0h)

Writte
Format
5, 6, 15, 16 B

Rserve
e for TCS

241-242
(00F1h-00F2h)

Selection of single remote control

c
orders

243
(00F3h)

5, 6, 15, 16 B

Reserve for selection of TCS

244-245
(00F4h-00F5h)

1, 2, 3, 4

Single remote control order words

follow
Each Remote Single Command TCS Word is encoded as follows:
TCS16
b15

TCS15

TCS14

TCS13

TCS12

TCS11

TCS10

TCS9
b08

TCS8
b07

TCS7

TCS6

TCS5

TCS4

TCS3

TCS2

TCS1
b00

ol order assigned to each bit in

n the remote control words
w
(address 00F0h)
The remote contro
and remote control
rol selection
se
words (address 00F3h) is predefined::
Word

Bit

Remote Control Word

Adresse bit
3840
(0F00h)

Selection Word (SBO)

Adresse bit
3888
(0F30h)

Remote Control Order

3841
(0F01h)

3889
(0F31h)

Reset of fault current

indication

02...14 38423854
(0F02h...0F0Eh)

38903902
(0F32h...0F3Eh)

Reserved

15

3903
(0F3Fh)

Check of the communication

by a visual signalization (*)

240
00
(00F0h)
01

3855
(0F0Fh)

Reset of phase currents

maximeter

(*): This command activates a rapid flash on the LED of fault detection on Flair 23DM for 30
seconds and permit so to check the communication between the master and the Flair 23DM.
The selection word is only used for the "confirmed SBO" mode.
Note: a single
le remote control order
or
changing to zero does not gen
nerate time-tagged events

16

NT00337-EN-01

Remote control zone

Flair 23DM

Command rejection at communication

munication level
Remote command may be rejected at communication
com
level with following reasons:
o exception 3 (Illegal data value) if remote command is inconsistent or in case of select/operate
issue (not selected, timeout elapsed, )
o exception 2 (Illegal Data Address) if requested command is not supported by the Flair 23DM
o exception 6 (Slave Busy) if Flair 23DM is busy (command under execution).
execution)
o
Direct mode
If remote control orders
ord
are configured in direct mode, the remote control order is executed
immediately on writing
wr
to the remote control word. Resetting is perrformed by the control logic
after the remote control order
ord has been taken into account.
Confirmed SBO mode
The remote control order
or
is executed in two steps:
1. Selection by th
he supervisor of the command to be sent by writing the bit in the remote
control selection word and
a checking the selection if necessary
cessary by re-reading
r
this word.
2. Execution of th
he command to be sent by writing the bit in the rem
mote control word.
Note: when this mode is selected, it applies to all control orders.
The remote control
rol order
ord is executed if the remote control selection
n word bit and the
associated remote control word bit are set, both word bits are reset
set by the control logic after
the
he remote control order
ord has been taken into account. Deselection
selection of the selection word bit
occurs:
if the supervisor
rvisor deselects
dese
it by writing in the selection word
if the supervisor selects (writes) a different bit from that alreadyy selected
if the supervisor
rvisor sets a bit in the remote control word that does not
n correspond to that
selected (in this case no remote control order
ord will be executed)
No remote control will be executed:
if the correspond
onding order is not sent within a period of 30 seconds
secon

NT00337-EN-01

17

Remote control order and status

zone

Flair 23DM

2.9 Remote Control Orde

er and Status Zone
Introduction
Status conditionss and remote indications are pre-assigned to fault detection or voltage
presence functions.
ons. They can be read using bit or word functions.
Remote Control Order and Status Zone
Z
The status condition
ition and remote indication zone contains 10 words that group together status
bits. It also provides
des the
t remote control order feedback code:
Description

Word address

Bit address

Control word

256 (0100h)

1000h...100Fh
Fh 1, 2, 3, 4

Status word

257 (0101h)

1010h...101Fh
Fh 1, 2, 3, 4

Remote indication no. 1 word

(TSS 1)

258 (0102h)

1020h...102Fh
Fh 1, 2, 3, 4

Remote indication no. 2 word

(TSS 2)

259 (0103h)

1030h...103Fh
Fh

Reserved

260263
(0104h0108h)

1040h...108Fh

Read

Writte Format

Control word (Address 0100h)

Word
Bit
256
00...03
(0100h)

Bit Address
Status
4096..4099
Reserved
(1000h...1003h)

04
05

4100 (1004h)
4101 (1005h)

Flair 23DM time incorrect (no reception of date and time)

Flair 23DM not synchronized
onized (too long time since last
refreshment or too big deviation)

06
07...15

4102 (1006h)
Flair 23DM initialization in progress
4103..4111
Reserved
(1007h...100Fh)

Note: bit 06 changing to zero doesn't

do
generate time-tagged
tagged events.

18

NT00337-EN-01

Remote control order and status

zone

Flair 23DM

Status word (Address 0101h)

The status word specifies
sp
the main functions when on:
Word
Bit
257
0012
(0101h)
13
1415

Bit Address
41124124
(1010h101Ch)
4125 (101Dh)
41264127
(101Eh101Fh)

Status
Reserved
Setting change of Flair 23DM
Reserved

Note: bit 13 changi

nging to zero does not generate time-tagged even
nts.
Remote indication No. 1 (Address 0102h)
The remote indication No. 1 signals the status related to the voltage detection:
Word
Bit
258
00
(0102h) 01
02
03
04
05
06
07
08
09
10
11
12...15

Bit Address
4128 (1020h)
4129 (1021h)
4130 (1022h)
4131 (1023h)
4132 (1024h)
4133 (1025h)
4134 (1026h)
4135 (1027h)
4136 (1028h)
4137 (1029h)
4138 (102Ah)
4139 (102Bh)
41404143
(102Ch...102Fh)

Remote indication
Voltage presence (on all phases)
Voltage presence V1 or U12
Voltage presence V2 or U13
Voltage presence V3 or U23
Residual voltage presence (summation of the three
phases) voltage presence loss (generate an event)
Transient
Reserved
Reserved
Voltage absence (sur toutes les phases)
phases
Voltage absence V1 or U12
Voltage absence V2 or U13
Voltage absence V3 or U23
Reserved

Note: voltage
oltage presence/absence per phase is valid if corresponding phase voltage
measurement is configured as "active". It relates
lates to simple or composed voltages depending
on "Voltage Measure Type" parameter.
Remote indication No. 2 (Address 0103h)
The remote indication No. 2 signals the status related to the current fault detection:
detection
Word
Bit
259
00
(0103h) 01
02
03
04
05
06
07
08
09...15
...15

NT00337-EN-01

Bit Adress
4144 (1030h)
4145 (1031h)
4146 (1032h)
4147 (1033h)
4148 (1034h)
4149 (1035h)
4150 (1036h)
4151 (1037h)
4152 (1038h)
41534159
(1039h...103Fh)

Remote indication
Phase fault
Earth fault
Earth fault on phase 1
Earth fault on phase 2
Earth fault on phase 3
Transient phase fault
Transient earth fault
Fault by test action
Phase or earth fault
Reserved

19

Time-tagged events

Flair 23DM

2.10 Time-tagged events

Introduction
The Flair 23DM includes
incl
a time-tagged event mechanism so thatt its operation can be
monitored using
sing a supervisor.
sup
This data can be retrieved
retri
via the Modbus link.
This data is volatile
latile and will therefore be lost if the product is de-energiz
ergized.
Event types
The Flair 23DM manages logic events, any
ny change of state on Flair 23DM logic variable
(bit in control, sta
atus or remote indication words).
Each event is ma
ainly characterized by:
an identifier: Modbus address of associated data bit
a value (for logic
lo
events, it is the direction of change)
a date and time: the event is time-tagged (resolution: 1 ms)
Time-Tagging
Time-tagging of events
e
uses the Flair 23DM internal clock. When
hen an event is detected, the
Flair 23DMs curre
ent time is associated with it.
During the initializati
lization phase, the clock starts at 1st January 2000
00 00h 00min 0sec.
It will be re-synchronize
synchronizes to the current date and time after reception
ption of the synchronization
or on time setting.
The chronology
ogy of detected events remains valid in all cases

Description of how to code an Event

An event is coded
d on 12 words with the following structure:

20

Word

Inform
mation

Coding

1
2...5

Event number
Date an
nd time of the
event

Between 1 and 65535

In IEC 60870-5-4 format

6 (MSB) Number
er of associated
events

0 (no secondary event associated with the Flair23DM

events)

6 (LSB)
7
8...11

Type of data
Event identifier
Associated data

12

Primary or secondary
event identifier

Boolean (04h)
Address of the associated databit
data
Direction of the event:
0: deactivation/disappearance
pearance
1: activation/appearance
Between 1 and 65533. Used to identify the event.

NT00337-EN-01

Time-tagged events

Flair 23DM
Nota:

Event numbering
ering starts at no. 1 and ends with no. 65535. When event
e
no. 65535 is
detected, the next event
ev
numbering restarts at no. 1.
The most significant
ificant byte of word no. 6 corresponds to the type of event (primary or
secondary). On Flair 23DM,
23DM events are always primary type (no associated
assoc
secondary events).
The event identifier always corresponds to a Modbus data adress defined on the Flair
23DM.
For Boolean
n type,
typ words 8, 9 and 10 are set to 0.
Word
rd 12 is incremented
increme
2 at a time on each event.

Event tables
man
an internal storage table with a capacity
city
The Flair 23DM manages
of 100 events. Up
pstream of the table, 2 words contain:
the current number
numb of events present in the queue (between
en 0 and 100)
the number of
o the last detected event
Both these words and
a the number of the first event in the table form
rm a header that will be
used by the supe
ervisor to detect presence of new events.
The table can be
e seen
s
as a FIFO (First In/First Out) type stack.

Header

Table of
100
events

Addresses
57344 (E000h)
57345 (E001h)

Description
Number of events in table
Number of last event in table

Read
3
3

Write

57346 (E002h)

Index 0 event (event number)

numbe

5734757357
Index 0 event (rest of data)
ata)
(E003hE00Dh)

5735857369
Index 1 event
(E00EhE019h)

...
...
5853358545
Index 99 event
(E4A5hE4B1h)

3
3

Note: reading the

e events table is not destructive. An event no. x will only be removed from
the table if 100 ne
ew events have been detected (in other words, event
eve no. x+100 has been
detected).
c
It is to the Modbus client(s) to detect loss events if the table of events has come full cycle
since the last reading from the client(s).

Initializing the Events Table

On starting, the
e Flair 23DM initializes its events table by filling all the registers (table and
header) with the value 0 (no event
ev
recorded).
When it starts, the Flair 23DM always adds three events:
initialization in progress
pro
date/time inco
orrect (not configured since start-up)
not synchronized
These three even
nts are destined for the supervisor for time synchronization
synchro
and detection of
product
ct resetting.

NT00337-EN-01

21

Flair 23DM

Time-tagged events

Read sequence
The consultation protocol for time-tagged events includes a standard
ndard sequence that can be
executed by a supervisor
superv
to detect and retrieve new events present
resent on the
t Flair 23DM.
This sequence is divided into two parts:
detection off new events on the Flair 23DM
reading of new events
eve
on the Flair 23DM
Detection of new
w events on the Flair 23DM: new events are detect
tected by periodic reading
of the header in the time-tagged
t
events zone (addresses E000h
0h to E002h).
If the number of last event in table changes between two headerr readings, one or more
events have been
n added
add to the table. The supervisor can then
n read the new events.
Read Previous Header
Head (n-1)
Address
Value
57344 (E000h)
X
57345 (E001h)
Y
57346 (E002h)
Z

Read Current Header

Hea
(n)
Address
Value
57344 (E000h)
X
57345 (E001h)
Y
57346 (E002h)
Z

Reading of new events on the Flair 23DM: on the basis of value

es read in the headers,
the supervisor ca
an determine the Modbus register ranges to be read to obtain the new
event data.
The number of new events
eve
detected equals Y-Y.
The supervisor de
etermines the position (index) in the table of the first and last new event
starting from the event
eve number stored at index 0 of the table (Z).
The Modbus register addresses associated with the new events ca
an be deduced from the
indexes:
event start address
ad
= E002h + index * 12
event end address
ddress = E002h + (index + 1) * 12 - 1

Loss of Events
If the number of new events
eve
exceeds the table capacity, only the 100 most recent events
will stillll be accessible.
accessi
The oldest events will be lost forever.
The supervisor
pervisor is responsible
respo
for retrieving events from the Flair 23DM.
23DM It is up to him to adapt
his consultation
n strategy
str
to avoid the loss of events.

22

NT00337-EN-01

Time-tagged events

Flair 23DM

List of possible events

The Flair 23DM has a number of time-tagged
time
events whose descriptions appear below.
Boolean events:
Data type: Boolean
Bo
(format code: 04h)
Possible value
es: 0 or 1
The descriptio
on corresponds to value 1 of the event.
The two columns on the right indicates the saving conditions of event depending to the type
of change of the associated variable.
variable
(0 -> 1 = appearance,
appearance 1 -> 0 = disappearance).
Adresse
Dc. Hexa.
4100 1004h
4101 1005h
4102 1006h
4125 101Dh
4128 1020h
4129 1021h
4130 1022h
4131 1023h
4132 1024h
4133 1025h
4136 1028h
4137 1029h
4138 102Ah
4139 102Bh
4144 1030h
4145 1031h
4146 1032h
4147 1033h
4148 1034h
4149 1035h
4150 1036h
4151 1037h
4152 1038h
3840 0F00h
3841 0F01h
3855 0F0Fh

NT00337-EN-01

Description
Flair 23DM with time incorrect
Flair 23DM not synchronized
Flair 23DM under initialisation
Setting change on Flair 23DM
Voltage presence (on all the phases)
Voltage presence (V1 or U12)
Voltage presence (V2 or U13)
Voltage presence (V3 or U23)
Residual voltage presence (summation of the three phases)
Transient Voltage presence Loss (generate
enerate an event)
event
Voltage absence (on all the phases)
Voltage absence (V1 or U12)
Voltage absence (V2 or U13)
Voltage absence (V3 or U23)
Phase fault
Earth fault
Earth fault on phase 1
Earth fault on phase 2
Earth fault on phase 3
Transient phase fault
Transient earth fault
Fault by test action
Phase or earth fault
Reset Maximum of current
Reset current fault
Module check

0 -> 1

1 -> 0

X
X

X
X

X
X
X
X
X
X
X
X

X
X
X
X
X

X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X

X
X
X
X
X
X
X
X
X

X
X

23

Access
ess to remote settings

Flair 23DM

2.11 Access to Remote Settings

Presentation
Access to the Flair 23DM remote settings via the Modbus communication
cation allows:
a
remote reading
ing of settings
remote modification
modifica
of settings (remote setting), provided this ha
as been enabled.

Settings zones
Description
Date of last setting

Word Addresses Read

76807683
3, 4
(1E00h1E03h)

Write

Remote settings zone no. 1

76847698
(1E04h1E12h)

3, 4

6,16

Remote settings zone no. 2

77127719
(1E20h1E27h)

3, 4

6,16

Remote settings zone no. 3

77207727
(1E28h1E2Fh)

3, 4

6,16

The date of last setting is in IEC 60870-5-4 format.

Remote settings zone no. 1 contains
ains the settings related to the current fault threshold and to
the voltage presence/absence threshold.
threshold
Remote settings zone no. 2 contains
ains the parameters related to the communication.
communication
Remote settings zone no. 3 contains some others parameters
ters related to measurement and
fault detection.
ed information about these zones will be given in the settings
setti
table.
Note: detailed

Remote Reading Procedure

To perform remote reading, the supervisor simply reads the value of the Modbus register for
the desired setting.
The value of a setting
setti is automatically updated when a value is chang
nged via the user
interface or via a remote setting.

Remote Setting Procedure

To perform remote setting,
setti
the supervisor should write the new value(s)
ue(s) of one or more
parameters.
One or more setting
gs can be the target of a single remote setting req
quest.
A remote setting request will return a Modbus error in the following cases:
c
remote settings
gs not enabled (specific product setting)
product unavaillable (processing of a previous remote setting req
quest in progress, or
editing during
ring a setting
sett
via the user screen)
one of the settin
ngs targeted is not accessible for remote setting.

24

NT00337-EN-01

Access to remote settings

Flair 23DM

Taking Account of Remote Setting

The Flair 23DM only
ly applies the new settings values after responding
ding to the Modbus write
request.
Flair 23DM checks the consistency of the parameters received and only validates values that
correspond to what can be set manually on the HMI (value between min and max and
respecting the steps between the values), in order to avoid errors of remote setting.
setting If a
parameter does not meet these criteria,, an error is returned to the master.
Settings table

Remote settings zone no. 1: parameters

param
of current fault detection and voltage presence/absence
sence/absence

Address
Dec.

Address
Hexa.

Format

Unit

7680 to
7683

Last setting change date

7684

1E00h
to
1E03h
1E04h

ms

Phase fault threshold "I>"

IEC
Datetime
16S

7685

1E05h

Earth fault threshold "I0>"

16S

7686
7687
7688
7689

1E06h
1E07h
1E08h
1E09h

16S
16S
16S
16S

7690

1E0Ah

7691

1E0Bh

Fault duration
Fault validation time
Inrush filtering time
Automatic fault indication
reset on voltage return
Maximum delay before to
reset the fault indication
Phase Voltage presence
threshold
Residual Voltage presence
threshold
Delay for R1 relay activation
on voltage return (T11)

Description

Range

Default
value

Access

Reading only

ms
s
s
s

100 to 800A or AutoAuto

mode or OFF
5 to 200A (1) or
Auto-mode or OFF
40 to 300ms
3s, 70s, OFF
3s, 70s, OFF
3s, 70s, OFF

Automode
Automode
60ms
70 s
3s
70 s

R/W
R/W
R/W
R/W

16S

2, 4, 8, 12,16 or 24h
24

4h

R/W

16S

R/W
R/W

40 to 90 %
80
(10% step)
step
7692
1E0Ch
16S
%
30 to 60 %
30
(10% step)
step
7693
1E0Dh
16S
ms
0 to 1s (0,1s step)
0,1s
1 to 21s (2s step)
1 to 10 mn (1 mn
step) + 15 mn
7694
1E0Eh
Delay for R1 relay release on
16S
ms
0 to 1s (0,1s step)
step
0,1s
voltage loss (T12)
1 to 3s (0,5s step)
step
7695
1E0Fh
Voltage absence threshold
16S
%
10 to 30 %
20
(10% step)
step
7696
1E10h
Delay for R2 relay activation
16S
ms
0 to 1s (0,1s step)
0,1s
on voltage loss (T21)
1 to 21s (2s
2s step)
1 to 10 mn (1 mn
step) + 15 mn
7697
1E11h
Delay for R2 relay release on
16S
ms
0 to 1s (0,1s step)
step
0,1s
voltage return (T22)
1 to 3s (0,5s step)
step
7698
1E12h
16S
0 = inactive
Inactive
Auto calibration (2)
Boolean
1 = active
(1) : 3 phases CTs mounting: 20 to 200A. 2 phases CTs + zero sequence CT mounting:: 5 to 200A.
(2) : If active, the Auto calibration is performed at each return of LV supply.

NT00337-EN-01

R/W
R/W
R/W

R/W
R/W
R/W

R/W
R/W

25

Access
ess to remote settings

Flair 23DM

Remote settings zone no. 2 : Modbus communication parameters.

parameters

Address
Dec.

Address
Hexa.

Description

Format

Unit

7712

1E20h

Auto-mode

Boolean

7713

1E21h

Baud rate

16S

7714

1E22h

Parity

16S

7715

1E23h

Number of stop bits

16S

7716
7717

1E24h
1E25h

Modbus address
Cubicle number

16S
16S

7718

1E26h

16S

7719

1E27h

Modbus remote mode

(Select before
Execute)
Remote setting

Boolean

Range

0= inactive
1= active
1= 4800 baud
2= 9600 baud
3= 19200 baud
4= 38400 baud
1 = None
2 = Even
3 = Odd
1= 1 stop bit
2= 2 stop bits
1 to 247
0 = Nott significant
Else: 1 to 29
1= direct mode
2= SBO active
(confirmed mode)

By default
value

Access

active

Auto-mode
(1)

Even

247
0

R
R

Direct

R/W

Authorized
R
0 = Not authorized
horized
1 = Authorized
(1): Speed is predefined at factory at 38400 bauds. If restarted, the Auto-mode restarts from 19200 bauds and
then upwards until it detects the real speed.
Rules of configuration:
The number of stop bit is automatically derived from parity defined (2 bits if parity = None).
None
The modification of the communication parameters (speed,
(speed parity, stop bits) is only possible if the Auto-Mode is not
activated.
Modifying
odifying the cubicle number causes the automatic assignment of the Modbus address:
address
(@ = 33 + 5*(CubicleNb-1))
Assigning a new Modbus Slave Address automatically resets Cubicle number to 0.

Remote settings zone no. 3: other parameters related to the current fault detection and voltage
presence/absence.

Address
Dec.

Address
Hexa.

Description

Format

Unit

7720

1E28h

CT mounting

16S

7721

1E29h

CT type

16S

7722

1E2Ah

Voltage measure type

7723

1E2Bh

7724

1E2Ch

Voltage detection
output relays logic
Voltage phase 1

7725

1E2Dh

Voltage phase 2

7726

1E2Eh

Voltage phase 3

7727

1E2Fh

Residual voltage

16S
(Boolean)
16S
(Boolean)
16S
(Boolean)
16S
(Boolean)
16S
(Boolean)
16S
(Boolean)

26

Range

1 = Type A (ooo)
2 = Type B (0oo)
3 = Type C (0)
1 = CT1
2 = CT2
0 = Simple
1 = Composed
0 = Direct
1 = Inverted
0 = Not measured
1 = Measured
0 = Not measured
1 = Measured
0 = Not measured
1 = Measured
0 = Not measured
1 = Measured

By default
value

Access

Type A

CT1

Simple
(dip switch)
Direct
(dip switch)
Measured
(dip switch)
Measured
(dip switch)
Measured
(dip switch)
Not
measured
(dip switch)

NT00337-EN-01

R
R
R
R
R

Date and time setting and

synchronization

Flair 23DM

2.12 Date and Time-Setting

Setting and Synchronization
Introduction
The Flair 23DM manages the date and time internally. If the auxiliary power supply
fails, this information continues to be maintained, as long as a battery in good working
order is used in the device.
The Flair 23DM internal time is used, in particular, to date alarms and events.
The Flair 23DM also delivers a Flair 23DM time incorrect data item (bit 04) to the control
word, indicating the need to set the time.

Time and date setting

When the Flair 23DM is energized, the time is set automatically from the battery-backed
clock, provided
vided the battery
b
is working.
The time and
nd date are set:
by writing,, in a single
sin
block, the new date and time value
lue in the synchronization
synchro
zone
(addresses
addresses 0002h to 0005h)
by using function
on 43 with sub-function
sub
16.
Synchronization
The time frame is used both for setting the time and synchronizing the Flair 23DM. In this
case, it should be transmitted regularly at close intervals (10 to 60 seconds) to obtain a
synchronous time. It is usually transmitted by broadcasting
broadcasting (slave number = 0).
In synchronous state, the absence of receipt of a time frame for more than 200 seconds
causes a loss of synchronism (bit
( 05 of the control word at 1).
On receipt of the date and time, the Flair 23DM saves the new date. It also checks whether
the difference between this new date and the current date is more than 100 ms. If so, the
Flair 23DM changes to nonnon synchronous state (bit 05 of the control word at 1). It will return
to synchronous state (bit 05
05 of the control word at 0) as soon as the time difference
between the new date it has received and the current date is less than 100 ms

Synchronization cycle
Each synchronization cycle is executed as follows:
Phase
1

NT00337-EN-01

Description
tion
The superrvisor writes its date and time value in the synchronization
ronization zone or by
function 43-16
43

The Flair 23DM changes to non-synchronous state (bit 05 of the control word at 1)
and resets
sets its clock.

If the reset
set amplitude is less than 100 ms, the Flair 23DM changes back to
synchronous state.

27

Flair 23DM

Date and time setting and

synchronization

Events generated
At each power-up,
up, Flair23DM generates
rates successively the following events:
Appearance of the incorrect time event
Appearance of the Not synchronous event
At the first broadcast of synchronization message by master (with date & time), slave
generates successively
ccessively the following events:
events
Disappearance of the incorrect time event
Disappearance of the Not synchronous event
After loss of synchronization, slave generates the following event:
Appearance of the Not synchronous event
After return of synchronization, slave
slav generates the following event:
Disappearance of the Not synchronous event
Clock accuracy
ccuracy is linked to the master and its control of the time frame transmission
tra
The clock accuracy
delay on the
e communication
communic
network. Before sending a time frame, the supervisor must
ensure that all the read
re requests sent have received a response.
onse. Synchronization
Sy
of the Flair
23DM is performed
rmed immediately after the frame is received.
For optimum
m synchronization,
synchr
the supervisor must compensate for the
t frame transmission
time. The frame transmission
transmissi time is compensated by the Flair 23DM.
23DM
If the frames pass
ss through
throu a gateway (multi-master operation), make sure that this does not
slow down the frames.
fram

28

NT00337-EN-01

Managing
ging the date and time using
function 43

Flair 23DM

2.13 Managing the Date and Time Using Function 43

Introduction
Access to and setting the date and
a time on Flair 23DM is also possib
ble via two sub-functions of
the Modbus
bus 43 function.
functio These two sub-functions will be referred to as function 43-15 and
function 43-16
6 hereafter.
here

Function 43-15
15 is a read
r
Flair 23DM date and current time function. It is an alternative to
Function 43-15
reading the Modbus
bus registers
re
at addresses 0002h to 0005h inclusive.
usive.
The IEC 60870-5-4
4 format is used for data returned by function 43-15
5 (common to reading via
the Modbus
bus registers).
registe
Request frame stru
ucture:
Slave Number

Function

1 byte
1 byte
Request destination:
stination: 43
1247 (unique) (decimal)

MEI Type
Reserved
(Sub-Function Code)
1 byte
1 byte
15 (decimal)
0

Function
2 bytes
CRC 16

Correct response frame structure:

str
Slave Number Function
1 byte
Request
destination:
1247
(unique)

NT00337-EN-01

MEI Type
Reserved Data
(Sub-Function Code)

1 byte
1 byte
43 (decimal) 15 (decimal)

1 byte
0

8 bytes
Date and
time in IEC
60
60870-5-4
format

Control
Word
2 bytes
CRC 16

29

Managing
ging the date and time using
function 43

Flair 23DM

Function 43-16
Function 43-16
16 is a write Flair 23DM date and current time function. It is an alternative to
writing the Modbus
us registers
re
at addresses 0002h to 0005h inclusive.
usive.
The IEC 60870-5-4
4 format is used for data supplied to function 43-16 (common to reading via
the Modbus registers).
registe
Correct request fra
ame structure:
Slave Number

Function

MEI Type
Reserve Data
(Sub-Function Code) d

Control
Word

1 byte
Request
destination:
0: broadcast
1247
(unique)

1 byte
43
(decimal)

1 byte
16 (decimal)

2 bytes
CRC 16

1 byte
0

8 bytes
D
Date
and
time in IEC
60870
60870-5-4
f
format

Response
onse frame structure: No response if it is sent in broadcast mo
ode. Otherwise the
response
onse is as follows:

30

Slave Number

Function

MEI Type
Reserve Data
(Sub-Function Code) d

Control
Word

1 byte
Request
destination
:
1247
(unique)

1 byte
43
(decimal)

1 byte
16 (decimal)

2 bytes
CRC 16

1 byte
0

8 bytes
Flair 23DM
date and
current time
in IEC
60870
60870-5-4
format after
updating

NT00337-EN-01

Flair 23DM

NT00337-EN-01

Personal notes

31

Schneider Electric Industries SAS

Schneider Electric Telecontrol
839 chemin des Batterses
Z.I. Ouest
01700 St Maurice de Beynost
Tel : +33 (0)4 78 55 13 13
Fax : +33 (0)4 78 55 50 00

As standards, specifications and designs change from time to time,

please ask for confirmation of the information given in this publication.

http://www.schneider-electric.com
E-mail : [email protected]
NT00337-EN-01

07/2013

Publication, production and printing : Schneider Electric Telecontrol

Made in France - Europe