Powermatic 2000 Table Saw - 1792000K

Download as pdf or txt
Download as pdf or txt
You are on page 1of 44

This Manual is Bookmarked

Operating Instructions and Parts Manual


10-inch Cabinet Saw
Model: 2000

Model 2000 Table Saw shown with optional extension table and legs

WMH TOOL GROUP


2420 Vantage Drive
Elgin, Illinois 60123 Part No. M-1791997
Ph.: 800-274-6848 Revision B 04/06
www.wmhtoolgroup.com Copyright © WMH Tool Group
WARRANTY AND SERVICE
WMH Tool Group, Inc., warrants every product it sells. If one of our tools needs service or repair, one of our
Authorized Service Center located throughout the United States can give you quick service. In most cases, any of
these WMH Tool Group Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or
®
perform routine maintenance and major repair on your POWERMATIC tools. For the name of an Authorized Service
Center in your area call 1-800-274-6848.
MORE INFORMATION
WMH Tool Group is consistently adding new products to the line. For complete, up-to-date product information, check
with your local WMH Tool Group distributor, or visit powermatic.com.
WARRANTY
POWERMATIC products carry a limited warranty which varies in duration based upon the product.

WHAT IS COVERED?
This warranty covers any defects in workmanship or materials subject to the exceptions stated below. Cutting tools,
abrasives and other consumables are excluded from warranty coverage.
WHO IS COVERED?
This warranty covers only the initial purchaser of the product.
WHAT IS THE PERIOD OF COVERAGE?
The general POWERMATIC warranty lasts for the time period specified in the product literature of each product.
WHAT IS NOT COVERED?
The Five Year Warranty does not cover products used for commercial, industrial or educational purposes. Products
with a Five Year Warranty that are used for commercial, industrial or education purposes revert to a One Year
Warranty. This warranty does not cover defects due directly or indirectly to misuse, abuse, negligence or accidents,
normal wear-and-tear, improper repair or alterations, or lack of maintenance.
HOW TO GET SERVICE
The product or part must be returned for examination, postage prepaid, to a location designated by us. For the name
of the location nearest you, please call 1-800-274-6848.
You must provide proof of initial purchase date and an explanation of the complaint must accompany the
merchandise. If our inspection discloses a defect, we will repair or replace the product, or refund the purchase price,
at our option.
We will return the repaired product or replacement at our expense unless it is determined by us that there is no
defect, or that the defect resulted from causes not within the scope of our warranty in which case we will, at your
direction, dispose of or return the product. In the event you choose to have the product returned, you will be
responsible for the handling and shipping costs of the return.
HOW STATE LAW APPLIES
This warranty gives you specific legal rights; you may also have other rights which vary from state to state.
LIMITATIONS ON THIS WARRANTY
WMH TOOL GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR
EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND
FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
WMH TOOL GROUP SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY,
OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE
OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
WMH Tool Group sells through distributors only. The specifications in WMH catalogs are given as general information
and are not binding. Members of WMH Tool Group reserve the right to effect at any time, without prior notice, those
alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever.

2
Table of Contents
WARRANTY AND SERVICE ........................................................................................................................ 2
Table of Contents.......................................................................................................................................... 3
Warnings ....................................................................................................................................................... 4
Introduction ................................................................................................................................................... 6
Specifications ................................................................................................................................................ 6
Shipping Contents......................................................................................................................................... 7
Unpacking.................................................................................................................................................. 7
Cleaning .................................................................................................................................................... 7
Contents of the Shipping Container .......................................................................................................... 8
Assembly..................................................................................................................................................... 10
Mounting Extension Wings...................................................................................................................... 10
Lock Knobs and Swivel Handles ............................................................................................................. 11
Dust Chute............................................................................................................................................... 11
Blade Installation/Replacement............................................................................................................... 12
Mounting Rails and Accu-Fence............................................................................................................ 12
Optional Wood Extension Table.............................................................................................................. 12
Switch Installation.................................................................................................................................... 12
Riving Knife and Guard Installation ......................................................................................................... 13
Grounding Instructions ................................................................................................................................ 14
Extension Cords ...................................................................................................................................... 14
Zero-Clearance Insert Setup ................................................................................................................... 15
Miter Slot Alignment ................................................................................................................................ 16
Tilt Stop Adjustment ................................................................................................................................ 16
Precision Miter Gauge ............................................................................................................................. 17
Riving Knife Adjustment .......................................................................................................................... 18
Insert Adjustment..................................................................................................................................... 19
Arbor and Arbor Bearing Removal .......................................................................................................... 19
Operating Controls ...................................................................................................................................... 20
Start/Stop................................................................................................................................................. 20
Safety Key ............................................................................................................................................... 20
Motor Cover............................................................................................................................................. 12
Adjustments ................................................................................................................................................ 14
Handwheel Adjustments.......................................................................................................................... 14
Drive Belt ................................................................................................................................................. 17
Operations................................................................................................................................................... 21
Overview.................................................................................................................................................. 21
Kickback .................................................................................................................................................. 21
Bevel and Miter Operations..................................................................................................................... 24
Safety Devices ............................................................................................................................................ 25
Feather Board and Push Blocks.............................................................................................................. 25
Push Stick................................................................................................................................................ 25
Filler Piece............................................................................................................................................... 25
Maintenance................................................................................................................................................ 26
Cleaning .................................................................................................................................................. 26
Lubrication ............................................................................................................................................... 26
Miscellaneous.......................................................................................................................................... 26
Troubleshooting .......................................................................................................................................... 27
Optional Accessories .................................................................................................................................. 28
Ordering Replacement Parts................................................................................................................... 28
Model 2000 Table Saw Parts List ............................................................................................................... 29
Wiring Diagrams.......................................................................................................................................... 38

The specifications in this manual are given as general information and are not binding. WMH Tool Group
reserves the right to effect, at any time and without prior notice, changes or alterations to parts, fittings,
and accessory equipment deemed necessary for any reason whatsoever.
3
Warnings
1. Read and understand the entire owners manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This table saw is designed and intended for use by properly trained and experienced personnel only.
If you are not familiar with the proper and safe operation of a table saw, do not use until proper
training and knowledge have been obtained.
5. Do not use this table saw for other than its intended use. If used for other purposes, WMH Tool Group
disclaims any real or implied warranty and holds itself harmless from any injury that may result from
that use.
6. Always wear approved safety glasses/face shields while using this table saw. Everyday eyeglasses
only have impact resistant lenses; they are not safety glasses.
7. Before operating this table saw, remove tie, rings, watches and other jewelry, and roll sleeves up past
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips
are recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• Lead from lead based paint.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety
equipment, such as face or dust masks that are specifically designed to filter out microscopic
particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the machine is properly grounded.
12. Make all machine adjustments or maintenance with the machine unplugged from the power source. A
machine under repair should be RED TAGGED to show it must not be used until maintenance is
complete.
13. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
14. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
15. Check the alignment of the riving knife, fence and miter slot to the blade. A caution decal is installed
on each guard to remind the operator of the dangers of improper machine operation.
16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.

4
17. Provide for adequate space surrounding work area and non-glare, overhead lighting.
18. Keep the floor around the machine clean and free of scrap material, oil and grease.
19. Keep visitors a safe distance from the work area. Keep children away.
20. Make your workshop child proof with padlocks, master switches or by removing safety keys.
21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
22. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other
moving parts. Do not overreach or use excessive force to perform any machine operation.
23. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and safer.
24. Use recommended accessories; improper accessories may be hazardous.
25. Maintain tools with care. Keep blade sharp and clean for the best and safest performance. Follow
instructions for lubricating and changing accessories.
26. Check the saw blade for cracks or missing teeth. Do not use a cracked or dull blade or one with
missing teeth or improper set. Make sure the blade is securely locked on the arbor.
27. Keep hands clear of the blade area. Do not reach past the blade to clear parts or scrap with the saw
blade running. Never saw freehand. Avoid awkward operations and hand positions where a sudden
slip could cause your hand to contact the blade.
28. Do not attempt to saw boards with loose knots or with nails or other foreign material, on its surface.
Do not attempt to saw twisted, warped, bowed or “in wind” stock unless one edge has been jointed for
guiding purposes prior to sawing.
29. Do not attempt to saw long or wide boards unsupported where spring or weight could cause the
board to shift position.
30. Always use the riving knife, blade guard, push stick and other safety devices for all operations where
they can be used. On operations such as dadoing or molding where the blade guard cannot be used,
use feather boards, fixtures and other safety devices and use extreme caution. Reinstall the riving
knife and blade guard immediately after completing the operation that required their removal.
31. Be sure the saw blade rotates clockwise when viewed from the motor side (left side) of the machine.
32. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do
not use your hands.
33. Do not stand on the machine. Serious injury could occur if the machine tips over.
34. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
35. Remove loose items and unnecessary work pieces from the area before starting the machine.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly
even death.

5
Introduction
This manual is provided by WMH Tool Group covering the safe operation and maintenance procedures
for a Powermatic Model 2000 Table Saw. This manual contains instructions on installation, safety
precautions, general operating procedures, maintenance instructions and parts breakdown. This machine
has been designed and constructed to provide years of trouble free operation if used in accordance with
instructions set forth in this manual. If there are any questions or comments, please contact either your
local supplier or WMH Tool Group. WMH Tool Group can also be reached at our web site:
www.wmhtoolgroup.com.

Specifications
Model number ......................................................................................................................................... 2000

Stock Number
3HP, 230V, 60Hz, 1 Phase, 3600 RPM, TEFC ........................................................................... 1791999
5HP, 230V, 60Hz, 1 Phase, 3600 RPM, TEFC ........................................................................... 1791998
5HP, Prewired 230V (for 460V see Note below), 60Hz, 3 Phase, 3600 RPM, TEFC................. 1791997

Table size with standard extensions (L x W/in.)............................................................................ 42 x 30 1/2


Table size without extensions (L x W/in.)...................................................................................... 22 x 30 1/2
Arbor diameter (in.) .................................................................................................................................... 5/8
Saw blade diameter (in.) ............................................................................................................................. 10
Arbor speed (RPM) ................................................................................................................................. 4300
Left tilt range ........................................................................................................................................... 0–45
Maximum depth of cut (in.)............................................................. 3-1/8 at 90-degrees; 2-1/8 at 45-degrees
Maximum diameter of dado (in.) ................................................................................................................... 8
Maximum width of dado cut (in.) ............................................................................................................ 13/16
Drive system ................................................................................................................................. Poly-V Belt
Table height to floor (in.) .......................................................................................................................34-1/2
Dust port diameter (in.) ................................................................................................................................. 4

Shipping weight (saw only) ..............................................................All Models: Net: 540 lbs, Gross: 604 lbs

Note: For 460V operation, magnetic switch (Part No. PM2000-293C) must be purchased separately and
installed. A qualified electrician is recommended.

The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, WMH Tool Group reserves the right to change specifications at any time and
without prior notice, without incurring obligations.

Read and understand the entire contents of this manual before attempting
assembly or operation! Failure to comply may cause serious injury

6
Shipping Contents
Unpacking
Remove box and wood crating completely from
around saw. Check for shipping damage. Report
any damage immediately to your distributor and
shipping agent. Do not discard any shipping
material until the Table Saw is assembled and
running properly.
Compare the contents of your container with the
parts lists in the next two pages to make sure all
parts are intact. Missing parts, if any, should be
reported to your distributor. Read the instruction
manual thoroughly for assembly, maintenance
and safety instructions.
1. Unbolt the saw from the skid.
2. Carefully slide the saw from the pallet onto
the floor.

Make sure that the castors do


not get damaged when removing from the
skid.
The Table Saw should be placed in an area with
a sturdy level floor, good ventilation and
sufficient lighting. Leave enough space around
the machine for mounting extension wings and
rail assemblies, and loading and off-loading
stock and general maintenance work.

Cleaning
Exposed metal surfaces, such as the table top
and extension wings, have been given a
protective coating at the factory. This should be
removed with a soft cloth moistened with
kerosene. Do not use acetone, gasoline, or
lacquer thinner for this purpose. Do not use
solvents on plastic parts, and do not use an
abrasive pad because it may scratch the
surfaces.

7
Contents of the Shipping Container
Main Saw Container Small Box

1 Table Saw (A) The small box consists of the following items:
1 Table Insert (B) 1 Push Stick (G)
The following items are inside the saw: 1 27mm Arbor Wrench (H)
2 Lock Knobs (J)
1 Miter Gauge Assembly (C) 2 Swivel Handles (K)
1 Blade Guard Assembly (D) 1 Riving Knife and Pawl Assembly (L)
1 Switch in box (E) 1 Hardware Bag (M) consisting of:
1 Owner's Manual (F) 6 3/8-16 x 1 Hex Cap Screw (AA)
1 Warranty Card (not shown) 6 3/8 Lock Washer (BB)
6 3/8 Flat Washer (CC)

Main Saw Container


Contents of the Small Box

8
Extension Tables
Two extension tables are packaged in individual
boxes.

Extension Tables

Side Cover Box


2 Hinge Pin (N)
1 Side Cover (O)

Contents of Side Cover Box

Fence and Rail


Carton contents and installation instructions for the
fence, rail system, and optional wooden extension
table are described in the Accu-Fence Owner's
Manual (No. M-0460284).

9
Assembly
Mounting Extension Wings
Referring to Figure 1:
1. Mount a cast iron extension wing (A) to the
right or left side of the table (B) using three
each 3/8-16x1 hex head screws (C), 3/8 lock
washers (D) and 3/8 flat washers (E). Have an
assistant hold the extension wing up to the
table while inserting the screws and washers.
Finger-tighten only.
Note: If an assistant is not available, hold the
wing in vertical position up to the saw table,
insert the middle screw and lock washer finger
tight, then pivot the wing to level position. Insert
the other two screws and washers finger tight. Figure 1
2. Mount the remaining extension wing to the
other side of the table in the same manner.

3. Make sure that the front edge of the extension


wings are flush with the front edge of saw table
(Figure 2).

Figure 2

4. Level the extension wing with the saw table


across its entire width (Figure 3) using a
straight edge and hammer with block of wood
(or rubber hammer).
As each area of the wing becomes flush with
the table, tighten the screw under that area.
Continue until all three screws are fully
tightened.
5. Repeat for the other extension wing.

Figure 3

10
Lock Knobs and Swivel Handles
Referring to Figure 4:
1. Thread the swivel handles (A) into the front and
side handwheels (C) and tighten with a 14mm
wrench.
2. Screw lock knobs (B) into the threaded
openings on the end of the shafts located in the
middle of the handwheels (C).
Note: Do not tighten the lock knobs all the way
at this time.

Figure 4

Dust Chute
Referring to Figure 5:
The Model 2000 comes equipped with a dust chute
and hose assembly (Inset 2) for use with a dust
collection system. If you do not intend to use a dust
collection system, the dust chute may be
disconnected and removed as described below.
To provide sufficient clearance for removal of the
dust chute:
1. Raise the blade height all the way up and set
the blade tilt to 0º (refer to Handwheel
Adjustments on page 14).
2. Remove the arbor nut and collar as described
in the Blade Installation/Replacement on page
12, steps 3-4.
Removing the dust chute:
3. Remove two socket head button screws (D, E)
with 4mm and 5mm hex wrenches respectively.
4. Through the opening on the left side of the
cabinet, remove the hose (Inset 1, 2) by
twisting and pulling back on the dust port (F).
Take the entire assembly (Inset 2) out through
the side opening.
Do not replace the arbor nut and collar at this time,
but proceed to the Blade Installation/Replacement
section (following page).
Figure 5

11
Blade Installation/Replacement

Use care when working with or


around sharp saw blade to prevent injury!
To install or replace a blade (refer to Figure 6):
1. Disconnect machine from power source.
2. Raise the blade height all the way up and set
the blade tilt to 0º (refer to Handwheel
Adjustments on page 14).
3. Press the arbor lock (D) in the direction shown
by the arrow to engage it into the slot in the
arbor (C). At the same time remove the arbor
nut (loosen with a 27mm wrench if necessary).
4. Remove the collar (B). Figure 6

5. Install the blade, making sure the cutting teeth


at the top of the blade point toward the front of
the saw. If unsure, refer to Figure 10 for the
proper blade orientation.
6. Replace the collar (B) and arbor nut (A).
7. Engage the arbor lock (D) and tighten the nut
(A) with a 27mm wrench.
8. Lower the blade below the table.

Mounting Rails and Accu-Fence


With the extension wings properly aligned, the rail,
guide tube and fence assembly can now be
mounted to the saw. Consult the Accu-Fence Figure 7
Owner's Manual (Part No. M-0460284) for
instructions.

Optional Wood Extension Table


For instructions on mounting the accessory wood
extension table, or router table, consult the
Accu-Fence Owner's Manual (Part No.
M-0460284) for instructions.

Switch Installation
Referring to Figure 7:
1. Place the switch assembly (A) under the rail
(B) and guide tube (C) so that the two holes in
the switch bracket (D) line up with the left two Figure 8
holes in the rail and guide tube.
Note: The screws and lock washers may Motor Cover
already have been installed when the rail and Line up the door hinges (A. Fig. 8) with the cabinet
guide tube were installed and need to be hinges (B, Fig. 8) and insert hinge pins (C, Fig. 8).
removed for this operation.
Note: The locking mechanism may require
2. Secure with two 1/4 lock washers (E) and adjustment to insure proper alignment.
1/4 x 3/4 hex cap screws (F).
12
Riving Knife and Guard Installation
Description
Referring to Figure 9:
The complete riving knife and guard assembly is
shown in A. Before installing onto the saw, the anti-
kickback pawl (E) must be separated from the
riving knife (H) as described below.
1. Press and hold the quick-release button (D) on
the base of the anti-kickback pawl (E) and lift
the pawl to remove from the riving knife (H).
Installation
Referring to Figure 10:
1. Set the saw blade to the 90 degree position
and raise it all the way (refer to Handwheel
Adjustments on page 14).
2. Remove the table insert (J).
3. Located inside the table and accessible
through the insert opening (Figure 10 inset),
place the quick-release clamp lock handle (K)
in the unlock position.
4. The floating clamp block (L) is spring loaded
and will move away (O) from the fixed
block (M), leaving a gap.
5. Insert the bottom of the riving knife (N1, N2) all
the way into the gap between the clamp blocks
(L, M), then lock the handle (K).
6. Replace the insert (J) back on the table. The Figure 9
saw blade and riving knife should protrude
through the slot in the insert.
Referring back to Figure 9:
7. Attach the anti-kickback pawl (E) by pressing
and holding the quick-release button (D) and
inserting the lock pin of the pawl into the
appropriate slot (F) on the riving knife.
8. In similar manner attach the guard (C) by
pressing and holding the quick-release button
(B) and inserting the lock pin of the guard into
the appropriate slot (G) on the riving knife.
You should feel a snap as each piece locks in
position. Attempt to lift as a test to make sure
that they are securely locked in place.
Adjustment
The clamping blocks (L, M, Fig. 10) are adjusted at
the factory and no further adjustment of the blade
guard and riving knife assembly should be
necessary. However, proper alignment is very
important. Before operating the table saw, read
the Riving Knife Adjustment section (page 18) to
verify and follow the adjustment procedure if Figure 10
necessary.
13
Grounding Instructions Adjustments
Electrical connections must be Handwheel Adjustments
made by a qualified electrician in compliance Referring to Figure 11:
with all relevant codes. This machine must be
properly grounded to help prevent electrical The front handwheel (B) controls the raising and
shock and possible fatal injury. lowering of the blade (blade height).
A power plug is not provided with the Model 2000. The side handwheel (C) controls the blade tilt and
You may either connect the proper UL/CSA listed castors. The blade can be adjusted for a tilt
plug or “hardwire” the machine directly to your between 90º (vertical or a setting of 0º on the scale)
electrical panel provided there is a disconnect near and 45º left tilt (D). The Model 2000 also has a
the machine for the operator. Consult electrical retractable castor system that can be extended to
drawings on pages 37-39 for further clarification of permit the table saw to be rolled from one location
wiring setup. to another.
This machine must be grounded. Grounding
provides a path of least resistance to help divert Blade height
current away from the operator in case of electrical
malfunction. 1. Loosen the lock knob (A) on the blade height
adjust handwheel.
Make sure the voltage of your power supply
matches the specifications on the motor plate of the 2. Turn the handwheel (B) clockwise to raise and
machine. counterclockwise to lower the blade.
3. Tighten the lock knob (A).
Extension Cords
If an extension cord is necessary, make sure the
cord rating is suitable for the amperage listed on Blade tilt adjustment
the machine's motor plate. An undersize cord will 1. Loosen the lock knob (A) on the side
cause a drop in line voltage resulting in loss of handwheel (C).
power and overheating.
2. Push the handwheel in (F).
The chart in Table 1 shows the correct size cord to
use based on cord length and motor plate amp 3. Turn the handwheel (C) counterclockwise to
rating. If in doubt, use the next heavier gauge. The adjust the saw blade down to 45º left tilt (D).
smaller the gauge number, the heavier the cord. Turn clockwise to adjust the saw blade to
maximum of 90º (D).
Extension Cord Length *
4. After selecting the position, tighten the lock
25 50 75 100 150 200 knob (A).
Amps feet feet feet feet feet feet

<5 16 16 16 14 12 12

5 to 8 16 16 14 12 10 NR

8 to 12 14 14 12 10 NR NR

12 to 15 12 12 10 10 NR NR

15 to 20 10 10 10 NR NR NR

21 to 30 10 NR NR NR NR NR
*based on limiting the line voltage drop to 5V at 150% of the
rated amperes.
NR: Not Recommended.
Table 1

Figure 11

14
Castor system adjustment
Retractable castors can be extended permitting the
saw to be moved:
1. Loosen the lock knob (A) on the side
handwheel (C).
2. Pull the handwheel out (F).
3. Turn the handwheel (C) clockwise to extend
the castors, raising the saw.
Note: Because of the weight of the machine,
both hands will be needed to turn the
handwheel. Raise the saw just enough to
permit moving to another location.
When the saw has been repositioned:
4. Retract the castors by turning the
handwheel (C) counterclockwise.
5. Push the handwheel in (F) and tighten the lock
knob (A).

Zero-Clearance Insert Setup


Under normal operations where the standard table
insert (which is provided) is used, the top edge of
the saw blade will come to rest approximately 1/8"
below the table surface when the blade height is
positioned all the way down.
In situations where a zero-clearance insert is
desired, the saw blade may be lowered further for
accommodation of inserts that have potential
clearance issues with the blade. This is done as
follows:
1. Remove the guard and pawl (Figure 9,
Items C, E).
2. Open the side cover and locate the blade depth
stop (A, Fig. 12) located between the arbor
Figure 12
pulley and motor.
3. Using a 6mm hex wrench, loosen the locking
screw (B, Fig. 12).
4. This will allow the depth stop to swing free and When the standard insert is to be used again, the
the saw blade to be adjusted lower. saw blade must be readjusted as follows:
5. With the height adjust handwheel (B, Fig. 11), 6. With the height adjust handwheel (B, Fig. 11),
lower the saw blade all the way. adjust height of the saw until the top of the saw
blade is 1/8" below the top of the table.
The zero-clearance insert can now be placed into
the table opening without contacting the saw blade. 7. The blade depth stop (A, Fig. 12) should be
resting against the trunnion (C, Fig. 12). Verify
Never use a zero-clearance that this is the case; then tighten the locking
insert with the saw blade in a tilted position. screw (B, Fig. 12).
Never operate the saw without the blade guard, 8. Replace the standard insert, pawl and blade
riving knife and anti-kickback pawls for guard.
operations where they can be used.

15
Miter Slot Alignment

Disconnect machine from


power source before making this adjustment.
To check the alignment of the miter slot to the
blade:
1. Raise the blade to its maximum height at the
90º vertical position (0º on scale).
2. Mark one tooth with a grease pencil and
position the tooth slightly above the top edge of
the table at the front.
3. Raise the miter gauge slightly out of its slot to
serve as a shoulder. Using a combination
square against the side of the bar, slide the
scale over until it touches the tip of the blade,
and lock the scale in position (A, Fig. 13).
4. Rotate the marked tooth so that it is slightly
above the table top at the rear (B, Fig. 13) and
using the square as before, check whether the
distance to the blade is the same.
5. If the distance is not the same, loosen the four
mounting screws that lock the table top to the
cabinet (two in front, two in back).
6. Nudge the table to bring the miter slot in line
with the blade.
The blade must be kept centered with the slot
in the table insert to ensure clearance at both
the 90º and 45º positions. Figure 13
7. After alignment, secure the table to the cabinet
by re-tightening the four mounting screws.

Tilt Stop Adjustment


1. Adjust the blade tilt for 90º as described in
Blade Tilt Adjustment on page 14.
2. Using a combination square, check the
90º stop (Figure 14 shows the 90º stop being
checked).
3. Adjust the 90º stop position if required, using
the stop screws as shown.
The 90º stop adjustment is accessible though
the left side opening. 14mm wrenches are
required to loosen the lock nut and adjust the
screw.
4. Check the accuracy of the pointer at 0º (blade
at 90º vertical position) and adjust if required.
5. Adjust the blade tilt for 45º. If required, adjust
the stop and pointer in the same manner. as Figure 14
above. The 45º stop adjustment is accessible
though the slot on the front of the cabinet.

16
Precision Miter Gauge 5. Tighten the lock handle (A).

Setting the miter gauge angle Verify that the scale indicator (G) reads 0º. If further
adjustment is necessary:
Referring to Figure 15:
6. Loosen the screw (F) and adjust the
The precision miter gauge has a rack and pinion indicator (G) until it reads 0º
adjustment for setting the angle. To operate:
7. Tighten the screw (F).
1. Slide the miter gauge into one of the slots on
the table top.
2. Loosen lock handle (A).
To adjust the body (B) of the miter gauge to the
desired angle:
3. Pull the spring-loaded knob (C) out and turn
until the body (B) of the miter gauge is at the
desired angle as indicated on the scale.
4. Tighten the lock handle (A).
Indent settings
There are indents at the 0º, 30º and 45º right and
left positions. At these settings, release the
knob (C) to engage the stop rod. Then tighten the Figure 15
lock handle (A).
Note: Do not rely solely on the indents for an Drive Belt
accurate setting. After the stop rod engages at the The saw is equipped with a poly-V belt.
0º, 30º and 45º positions, make a fine adjustment
with the knob (C), if necessary, setting it against Referring to Figure 16:
the scale indicator. To adjust the belt tension – loosen the hex nut
Extension plate (B) on the motor pivot and hex cap screw (A) on
the bracket with a 19mm socket or wrench. Pivot
The extension plate (D) can be adjusted by sliding the motor (C) and bracket to the right to increase
to the right or left or removed entirely. the belt tension. Retighten both screws (A, B).
To adjust – loosen two lock handles (E), position To remove and replace belt – loosen the hex
the extension plate and tighten the lock handles. nut (B) on the motor pivot and hex cap screw (A)
To remove – slide the extension plate completely on the bracket with a 19mm socket or wrench.
off and remove the lock handles (E) and mounting Pivot the motor (C) and bracket to the left as far as
hardware. possible. Remove the old poly-V belt (D) and
replace. Adjust the belt tension as described
Calibrating the miter gauge above.
1. Place the miter gauge in one of the slots (H) on
the table top.
2. Set the miter gauge to 90º (0º setting on the
scale) by loosening the lock handle (A), then
pulling the spring-loaded knob (C) out and
turning the body (B) until 0º is indicated on the
scale (F).
3. Measure the accuracy of the gauge against the
slot with a combination square.
If adjustment is necessary:
4. Adjust the body (B) until it is perfectly square
(90º) to the miter slot (H).

Figure 16

17
Riving Knife Adjustment
Lateral alignment
The saw blade and riving knife must be in line as
close as possible with each other (lateral
alignment) for the prevention of kickback. Upon
initial blade guard and riving knife installation no
further adjustment should be necessary. Alignment
should be checked and adjusted, if required, after
each blade change.
Check the alignment as follows:
1. Remove the blade guard and pawl (C, E,
Fig. 9).
2. Place a straightedge (A, Fig. 17) on the table
so it rests against the blade (B, Fig 17) and
riving knife (C, Fig. 17). Rotate the blade so the
Figure 17
top of the blade tooth touches the straightedge.
The saw blade and riving knife must be in line.
If adjustment is required:
3. Remove the blade guard (C, Fig. 9) and table
insert.
4. Loosen the lock handle (A, Fig. 18) and
remove the riving knife, making a note as to
which direction the riving knife needs to be
moved to align it with the saw blade.
5. Using a 3mm hex wrench, make adjustments
to four set screws (D, Fig. 19) accessible
through openings located in the corners of the
floating clamp block (B, Fig. 19).
Adjust any number of setscrews required to Figure 18
bring the riving knife in alignment with the saw
blade. Then reinsert the riving knife, secure by
tightening the lock handle (A, Fig. 18) and
check the alignment per step 2.
Note: Position the lock handle towards the saw
blade as shown in Figure 18. This will avoid the
table insert from being lifted when the blade is
raised with the handwheel.
6. Repeat steps 3–5 until the alignment is correct.
Blade proximity alignment
The gap between the saw blade and riving knife
must be between 3 and 8mm (Figure 20). If
adjustment is needed, note whether the blade to
knife gap needs to be increased or decreased.
Then adjust as follows:
1. Remove the blade guard, pawl, table insert and
riving knife.
Referring to Figure 19:
2. With a 5mm hex wrench, loosen two socket Figure 19
head button screws (E).

18
Note: These screws are accessible through
openings on the floating clamp block (B)
located diagonally on either side of the lock
handle (A). They secure the fixed clamp
block (C) to the riving knife extension plate (F).
Loosening these screws (E) will allow the fixed
clamp block (C) to slide back and forth on the
extension plate (F).
3. Slide the fixed clamp block (F) toward or away
from the saw blade as required.
4. Tighten the socket head button screws (E).
5. Reinsert the riving knife; tighten the lock handle Figure 20
(A, Fig. 18) and check that the saw blade/knife
gap is between 3 - 8mm (Figure 20).
Note: Attempt to make the gaps as even as
possible.

Insert Adjustment
Adjust the setscrews in the insert with a 3mm hex
wrench (Figure 21) to ensure that the insert is
stable and flush with the table top.

Figure 21

Arbor and Arbor Bearing Removal


The saw arbor is press fit in the saw raising arm
housing. If the arbor needs to be removed for
bearing replacement, it should be done by a
qualified service technician. Call your customer
service representative at the phone number on the
front cover.

19
Operating Controls
Start/Stop
Power Indicator Light – The start switch has a
power indicator lamp which is on whenever there
is power connected to the saw, not just when the
saw is running. Do not assume that no light means
there is no power to the machine. If the bulb is bad,
there will no indication. Always check before use.

Do not rely that no light means


no power to the machine. Always check for
power first. Failure to comply may cause
serious injury!
Referring to Figure 22:
Start – Press the green start switch.
When power is connected to the machine, the
green light is always on regardless of whether the
saw is running or not.
Stop – Press the red switch to stop. Figure 22
Reset – In the event that the saw stops without
pressing the stop button, as the result of a tripped
fuse or circuit breaker, etc.:
1. Press red button to reset
2. Press the green button to restart the machine.

Safety Key
The start/stop switch on the Model 2000 comes
equipped with a magnetic safety key. When in
place on the switch as shown in Figure 22, the
magnetic safety key trips a relay which will allow
the machine to start and stop when the respective
switches are pressed. Being magnetic, the lock can
be removed to make the machine inoperable and
can be hidden for safe storage by attaching it
underneath the rail or an other magnetic surface.
When using the saw, place the key on the switch
cover lining up the arrow on the key with the
REMOVE arrow on the cover. Then rotate the key
so the arrow lines up with the LOCK arrow. This will
prevent the safety key from coming loose from
vibration when the machine is in use.

20
Operations
Overview
Familiarize yourself with the location and
operation of all controls and adjustments and the
use of accessories such as the miter gauge and
rip fence.

Kickback
Serious injury can result from kickbacks which
occur when a work piece binds on the saw blade Figure 23
or binds between the saw blade and rip fence or
other fixed object. This binding can cause the Dull, badly set, improper, or improperly filed
work piece to lift up and be thrown toward the cutting tools and cutting tools with gum or resin
operator. adhering to them can cause accidents. Never
use a cracked saw blade. The use of a sharp,
Listed below are conditions, which can cause well maintained, and correct cutting tool for the
kickbacks: operation will help to avoid injuries.
• Confining the cutoff piece when crosscutting Support the work properly and hold it firmly
or ripping. against the gauge or fence. Use a push stick or
• Releasing the work piece before completing push block when ripping short, narrow (6" width
the operation or not pushing the work piece or less), or thin work. Use a push block or miter
all the way past the saw blade. gauge holddown when dadoing or molding.
• Not using the riving knife when ripping or not
For increased safety in crosscutting, use the
maintaining alignment of the riving knife with
provided extension plate (Figure 24) attached to
the saw blade.
the miter gauge using the holes provided in the
• Using a dull saw blade.
gauge.
• Not maintaining alignment of the rip fence so
that it tends to angle toward rather than
away from the saw blade front to back.
• Applying feed force when ripping to the
cutoff (free) section of the work piece
instead of the section between the saw
blade and fence.
• Ripping wood that is twisted (not flat), or
does not have a straight edge, or a twisted
grain.
To minimize or prevent injury from kickbacks:
• Avoid conditions listed above.
• Wear a safety face shield, goggles, or
glasses. Figure 24
• Do not use the miter gauge and rip fence in Never use the fence as a length stop when
the same operation unless provision is made crosscutting. Do not hold or touch the free end
by use of a facing board on the fence so as or cutoff section of a workpiece. On through-
to allow the cutoff section of the workpiece sawing operations, the cutoff section must NOT
to come free before the next cut is started be confined.
(see Figure 30).
Always keep your hands out of the line of the
• As the machine receives use, the operation
saw blade and never reach back of the cutting
of the anti-kickback pawls should be
blade with either hand to hold the workpiece.
checked periodically (Figure 23). If the pawls
do not stop the reverse motion of a Bevel ripping cuts should always be made with
workpiece, resharpen all the points. the fence on the right side of the saw blade so
• Where possible, keep your face and body that the blade tilts away from the fence and
out of line with potential kickbacks including minimizes the possibility of the work binding and
when starting or stopping the machine. the resulting kickback.

21
Rip Sawing The rip fence (A, Fig. 26) should be set for the
Ripping is where the work piece is fed with the width of the cut (C, Fig. 26) by using the scale
grain into the saw blade using the fence as a on the front rail, or by measuring the distance
guide and a positioning device to ensure the between the blade (B) and fence (A). Stand out
desired width of cut (Figure 25). of line with the saw blade and workpiece to
avoid sawdust and splinters coming off the blade
or a kickback, if one should occur.
If the work piece does not have a straight edge,
attach an auxiliary straight edged board on it to
provide one against the fence. To cut properly,
the board must make good contact with the
table.
In ripping, use one hand to hold the board down
against the fence or fixture, and the other to
push it into the blade between the blade and the
fence. If the workpiece is narrower than 6" or
shorter than 12", use a push stick or push block
to push it through between the fence and saw
blade (Figure 27). Never push in a location such
Figure 25
that the pushing hand is in line with the blade.
Move the hand serving as a hold-down a safe
Before starting a ripping cut, distance from the blade as the cut nears
be sure the fence is clamped securely and completion. For very narrow ripping where a
aligned properly. push stick cannot be used, use a push block or
• Never rip freehand or use the miter gauge in auxiliary fence. Always push the workpiece
combination with the fence. completely past the blade at the end of a cut to
• Never rip workpieces shorter than the saw minimize the possibility of a kickback.
blade diameter.
• Never reach behind the blade with either
hand to hold down or remove the cutoff
piece with the saw blade rotating.
Always use the blade guard, riving knife and
anti-kickback pawls. Make sure the riving knife is
properly aligned. When wood is cut along the
grain, the kerf tends to close and bind on the
blade and kickbacks can occur.
Note: A caution decal is installed on each guard
to remind the operator of the dangers of
improper machine operation.

Figure 27

Figure 26

22
When ripping long boards, use a support at the Crosscutting should never be done freehand nor
front of the table, such as a roller stand, and a should the fence be used as an end stop unless
support or "tailman" at the rear as shown in an auxiliary block is clamped to the front of the
Figure 28. blade area such that the cutoff piece comes free
of the block before cutting starts (Figure 30).
Never use the rip fence beyond the point where
the carriage is flush with the end of the rails.
Have the blade extend about 1/8" above the top
of the workpiece. Exposing the blade above this
point can be hazardous.

Figure 30
Length stops should not be used on the free end
of the workpiece in the cutoff area.
Do not crosscut workpieces shorter than 6".
Before starting a cut, be sure the miter gauge is
Figure 28 securely clamped at the desired angle. Hold the
workpiece firmly against the table and back
against the miter gauge. Always use the saw
guard and riving knife and make sure the riving
knife is properly aligned.
Crosscutting
For 90 degree crosscutting, most operators
Crosscutting is where the workpiece is fed cross
prefer to use the left-hand miter gauge slot.
grain into the saw blade using the miter gauge to
When using it in this position, hold the workpiece
support and position the workpiece (Figure 29).
against the gauge with the left hand and use the
right hand to advance the workpiece. When
using the right hand slot for miter and compound
crosscutting so that the blade tilts away from the
gauge, the hand positions are reversed.
When using the miter gauge, the workpiece
must be held firmly and advanced smoothly at a
slow rate. If the workpiece is not held firmly, it
can vibrate causing it to bind on the blade and
dull the saw teeth.

Figure 29

23
Bevel and Miter Operations Dado Cutting – Dadoing is cutting a wide
groove into a workpiece or cutting a rabbet
Bevel Cut – A bevel cut is a special type of along the edge of a workpiece. A dado insert,
operation where the saw blade is tilted at an shown in Figure 33, is necessary for this type of
angle less than 90 degrees to the table top
operation.
(Figure 31). Operations are performed in the
same manner as ripping or crosscutting except
the fence or miter gauge should be used on the Do not use the standard table
right-hand side of the saw blade to provide insert for dadoing operations.
added safety in avoiding a binding action
between the saw blade and the table top. When
beveling with the miter gauge, the workpiece
must be held firmly to prevent creeping.

Figure 33
The process of cutting 1/8" to 13/16" grooves in
workpieces is accomplished by the use of a
stacked dado blade set or an adjustable type
blade mounted on the saw arbor. By using
various combinations of the stacked dado
blades, or properly setting the dial on an
Figure 31 adjustable blade, an accurate width dado can be
made. This is very useful for shelving, making
Crosscut – Crosscuts made at an angle to the joints, tenoning, etc. The guard, riving knife, and
edge of the workpiece are called miters anti-kickback pawls supplied with the saw
(Figure 32). Set the miter gauge at the required should be used for all cutting operations where
angle, lock the miter gauge, and make the cut they can be used. When performing operations
the same as a normal crosscut except the where the guard can not be used, as in some
workpiece must be held extra firmly to prevent dadoing operations, alternative safety
creeping. precautions should be taken. These include
Note: When making compound miters (with push sticks, feather boards, filler pieces, fixtures,
blade tilted) use the miter gauge in the right jigs and any other appropriate device that can
hand slot to provide more hand clearance and be utilized to keep operator's hands away from
safety. the blade. Upon completion of the operation
requiring removal of the guard, the entire guard
Have the blade extend only 1/8" above the top of assembly must be placed back on the machine
the workpiece. Exposing the blade above this in its proper working order.
point can be hazardous.
Never use a dado head in a
tilted position. Never operate the saw without
the blade guard, riving knife and anti-
kickback pawls for operations where they
can be used.

Figure 32

24
Safety Devices
Feather Board and Push Blocks
A feather board or push block is not provided but
can be purchased by calling customer service at
the number shown on the cover and ordering
stock number 709721 (feather board) or 708815
(push block). In addition, a multitude of after
market products are available that can be used
in conjunction with the miter slot and fence.
These can be purchased at most woodworking
stores that sell table saws and accessories.

Push Stick
The use of a push stick provides an added level
of safety for the operator and is provided with
this machine.

Filler Piece
Figure 34 – Filler Piece
A filler piece (Figure 34) is necessary for narrow
ripping and permits the blade guard to remain on
the machine. It also provides space for the safe
use of a push stick.

25
Maintenance
Always disconnect power to the machine before performing maintenance. Failure
to do this may result in serious personal injury.
• Keep the inside of the cabinet and trunnion
Cleaning area clean.
Note: The following maintenance schedule • Check for excessive play in the tilting and
assumes the saw is being used every day. raising mechanism and in the saw arbor and
Daily: re-adjust as required.
• Check for belt tension and wear. Readjust or
• Wipe down the table surface and grooves
replace belt as required.
with a rust preventive.
• Clean the pitch and resin from the saw Lubrication
blade.
Weekly: • Grease the tilting worm gear, raising worm
gear, castor system worm gear and the
• Table surface must be kept clean and free of trunnion areas with a good grade non-
rust for best results. Apply a coat of paste hardening grease.
wax to the surface to facilitate this. An • Check all adjustments after lubricating.
alternative is to apply white talcum powder,
rubbed in vigorously once a week with a Miscellaneous
blackboard eraser; this will fill casting pores
and form a moisture barrier. This method Always be aware of the condition of your
provides a table top that is slick and allows machine. Routinely check the condition of the
rust rings to be easily wiped from the following items and repair or replace as
surface. Important also is the fact that necessary:
talcum powder will not stain wood or mar
• Mounting bolts
finishes as wax pickup does.
• Power switch
• Clean the motor housing with compressed
air. • Saw blade
• Wipe down the fence rails with a dry silicon • Blade guard assembly
lubricant.
Periodic:

26
Troubleshooting
Trouble Probable Cause Remedy

Tilt or raising clamp knobs not


Tighten knobs.
tightened.

Excessive vibration. Blade out of balance. Change blade. [page 12]

Bad motor. Replace motor.

Loose arbor or motor sheave. Tighten set screws.

Cuts out-of-square Miter gauge out of adjustment. Reset pointer. [page 17]
when crosscutting. Miter slot misaligned. Realign table. [page 16]

Excessive feed. Reduce feed.

Bad motor. Replace motor.


Motor stalls or
Dull or incorrect blade. Replace blade. [page 12]
workpiece binds or
burns. Miter slot misaligned. Realign miter slot. [page 16]

Realign fence. [see Fence Manual


Fence misalignment.
No. M-0460284]

Cuts not true at 90 or


Stop screws not set properly. Readjust stop screws. [page 16]
45 degrees.

Lock knob not released. Loosen lock knob.

Tilt or saw raising Worm and worm gear segment caked


Clean and re-grease.
handwheels difficult with sawdust and pitch.
to turn.
Worm and worm gear segment out of Realign worm and worm gear
alignment. segment.

Correct overload condition such as


Motor overloaded.
reducing the feed rate.
Motor overheats.
Clean sawdust from fan and duct
Improper cooling of motor.
areas of motor.

Request voltage check from power


Low voltage. company and correct low voltage
Motor starts slowly or condition.
fails to come up to
speed. Centrifugal switch not operating. Replace switch.

Bad motor. Replace motor.

Power line overloaded. Correct overload condition.

Undersize wires in supply system. Increase supply wire size.


Motor fails to develop
full power. Request voltage check from power
Low voltage.
company and correct condition.

Bad motor. Replace motor.

27
Optional Accessories
2195042K Accu-Fence and rail system for ripping 50" to right and 12" to left of saw blade.
2195079Z Accu-Fence - fence assembly only, no rails.
2195063K Accu-Fence and rail system for ripping 30" to right and 12" to left of saw blade.
1791787 Low Profile Riving Knife.
1791790 Table Insert.
1791788 Dado Insert Plate for 8" dado head. Wt. 1 lb. (.45 kg).
2726008 Replacement side panel kit for Model 66 Accu-Fence.
1791789 Miter Gauge. Wt. 4 lbs. (1.8kg).
6827044 Motor cover.
708295 Tenoning Jig.
2328003 Zero Clearance Insert.
6441000Z Set of 2 legs for 6827028 table.
6682004 Rout-R-Lift with deluxe fence.
6827041 Wooden Extension Table for 50" capacity with Rout-R-Lift hole.
6827043 Wooden Extension Table for 30" capacity with Rout-R-Lift hole.
6827040 Wooden Extension Table for 50" capacity without Rout-R-Lift hole.
6827042 Wooden Extension Table for 30" capacity without Rout-R-Lift hole.

Ordering Replacement Parts


To order parts or reach our service department, call 1-800-274-6848 between 7:30am and 5:30pm (CST),
Monday through Friday. Having the Model Number and Serial Number of your machine available when
you call will allow us to serve you quickly and accurately.

28
Model 2000 Table Saw Parts List
Table & Cabinet Assembly

Index No. Part No. Description Size Qty


1 ...............PM2000-101 ............Base ..................................................................... .................................... 1
2 ...............PM2000-102 ............Cabinet................................................................. .................................... 1
3 ...............TS-0255041 .............Button Head Socket Screw .................................. 5/16-18x3/4................. 8
4 ...............TS-0680031 .............Flat Washer.......................................................... 5/16 ............................. 8
5 ...............PM2000-105 ............Powermatic Name Plate ...................................... .................................... 1
6 ...............PM2000-106 ............Button Head Socket Screw .................................. 5/16-18x3/8................. 2
7 ...............PM2000-107 ............Lock Screw........................................................... .................................... 2
8 ...............TS-081C011.............Flat Head Machine Screw.................................... #10-24x1/4.................. 2
9 ...............PM2000-109 ............Pointer.................................................................. .................................... 2
10 .............PM2000-110 ............Pointer Block ........................................................ .................................... 2
11 .............TS-081C032.............Pan Head Screw .................................................. #10-24x1/2.................. 2
12 .............PM2000-112 ............Tilt Angle Scale .................................................... .................................... 1
13 .............TS-0254021 .............Button Head Socket Screw .................................. 1/4-20x1/2................... 2
14 .............PM2000-114 ............Scale Base ........................................................... .................................... 1
15 .............PM2000-115 ............Latch Post ............................................................ .................................... 1
16 .............TS-0561021 .............Hex Nut ................................................................ 5/16-18........................ 1
17 .............PM2000-117 ............Dust Plate............................................................. .................................... 1
18 .............PM2000-118 ............Bushing ................................................................ .................................... 1
19 .............TS-0050011 .............Hex Cap Screw .................................................... 1/4-20x1/2................... 4
20 .............TS-0680021 .............Flat Washer.......................................................... 1/4 ............................... 6
21 .............PM2000-121 ............Dust Port .............................................................. .................................... 1
22 .............TS-0267021 .............Set Screw............................................................. 1/4-20x1/4................. 13
23 .............1791790 ...................Table Insert .......................................................... .................................... 1
24 .............PM2000-124 ............Ball Plunger.......................................................... .................................... 2
25 .............PM2000-125 ............Table .................................................................... .................................... 1
26 .............PM2000-126 ............Extension Table ................................................... .................................... 2
27 .............TS-0680041 .............Flat Washer.......................................................... 3/8 ............................. 10
28 .............TS-0720091 .............Lock Washer ........................................................ 3/8 ............................. 10
29 .............TS-0720071 .............Flat Washer.......................................................... 1/4 ............................... 2
30 .............PM2000-130 ............Strain Relief.......................................................... .................................... 1
.................PM2000-130A ..........Strain Relief (for 5HP/1Ph only)........................... .................................... 1
31 .............TS-0060061 .............Hex Cap Screw .................................................... 3/8-16x1.................... 10
32 .............PM2000-132 ............Dust Chute ........................................................... .................................... 1
33 .............TS-0720081 .............Lock Washer ........................................................ 5/16 ............................. 4
34 .............TS-0255021 .............Button Head Socket Screw .................................. 5/16-18x1/2................. 4
35 .............PM2000-135 ............Push Stick ............................................................ .................................... 1
36 .............PM2000-136 ............Retaining Ring ..................................................... .................................... 5
37 .............PM2000-137 ............Key ....................................................................... 5x5x18 ........................ 4
38 .............PM2000-138 ............Sprocket ............................................................... .................................... 5
39 .............TS-0208131 .............Socket Head Cap Screw...................................... 5/16-18x2-1/2.............. 8
40 .............BB-6904ZZ...............Ball Bearing.......................................................... 6904ZZ........................ 3
41 .............PM2000-141 ............Shaft..................................................................... .................................... 3
42 .............PM2000-142 ............Lead Screw .......................................................... .................................... 1
43 .............PM2000-143 ............Adjusting Block .................................................... .................................... 4
44 .............TS-0640111 .............Nylon Insert Lock Nut........................................... 1/2-13.......................... 4
45 .............PM2000-145 ............Elevating Block .................................................... .................................... 4
46 .............PM2000-146 ............Castor................................................................... .................................... 4
47 .............PM2000-147 ............Bracket ................................................................. .................................... 1
48 .............BB-51104 .................Thrust Bearing ..................................................... 51104 .......................... 1
49 .............PM2000-149 ............Chain.................................................................... .................................... 1
50 .............PM2000-150 ............Dust Collection Tube............................................ .................................... 1

29
Table & Cabinet Parts Assembly

30
Trunnion & Motor Assembly Parts List

Index No. Part No. Description Size Qty


1 ...............PM2000-201 ............Knob..................................................................... .................................... 2
2 ...............PM2000-202 ............Hand Wheel ......................................................... .................................... 2
3 ...............TS-0270051 .............Set Screw............................................................. 5/16-18x1/2................. 2
4 ...............PM2000-204 ............Collar.................................................................... .................................... 1
5 ...............TS-0270011 .............Set Screw............................................................. 5/16-18x1/4................. 4
6 ...............PM2000-206 ............Washer................................................................. .................................... 2
7 ...............TS-0810012 .............Round Head Screw.............................................. #10-24x1/4.................. 1
8 ...............PM2000-208 ............Pointer.................................................................. .................................... 1
9 ...............PM2000-209 ............Bracket ................................................................. .................................... 1
10 .............PM2000-210 ............Roll Pin................................................................. .................................... 1
11 .............TS-0271131 .............Set Screw............................................................. 3/8-16x2...................... 1
12 .............TS-0561031 .............Hex Nut ................................................................ 3/8-16........................ 14
13 .............PM2000-213 ............Front Trunnion ..................................................... .................................... 1
14 .............TS-0267041 .............Set Screw............................................................. 1/4-20x3/8................... 9
15 .............PM2000-215 ............Key ....................................................................... 5x5x25 ........................ 3
16 .............PM2000-216 ............Worm Gear........................................................... .................................... 1
17 .............TS-0256051 .............Button Head Socket Screw .................................. 3/8-16x1...................... 8
18 .............PM2000-218 ............Lock Nut ............................................................... 5/8-18 L.H. .................. 1
19 .............PM2000-219 ............Support Base ....................................................... .................................... 1
20 .............PM2000-220 ............Raising Shaft........................................................ .................................... 1
21 .............PM2000-221 ............Woodruff Key ....................................................... .................................... 2
22 .............PM2000-222 ............Roll Pin................................................................. .................................... 3
23 .............PM2000-223 ............Bushing ................................................................ .................................... 1
24 .............PM2000-224 ............Worm.................................................................... .................................... 2
25 .............PM2000-225 ............Shaft..................................................................... .................................... 1
26 .............PM2000-226 ............Bushing ................................................................ .................................... 1
27 .............PM2000-227 ............Worm.................................................................... .................................... 1
28 .............TS-0209061 .............Socket Head Cap Screw...................................... 3/8-16x1-1/4................ 9
29 .............TS-0680041 .............Flat Washer.......................................................... 3/8 ............................... 3
30 .............TS-0720091 .............Lock Washer ........................................................ 3/8 ............................. 18
31 .............PM2000-231 ............Bracket ................................................................. .................................... 1
32 .............PM2000-232 ............Flat Head Machined Screw.................................. 1/4-20x3/4................... 2
33 .............TS-0254031 .............Button Head Socket Screw .................................. 1/4-20x3/4................... 1
34 .............PM2000-234 ............Shaft..................................................................... .................................... 1
35 .............TS-0060061 .............Hex Cap Screw .................................................... 3/8-16x1-1/4................ 2
36 .............PM2000-236 ............Washer................................................................. .................................... 2
37 .............PM2000-237 ............Lock Nut ............................................................... 1-1/8-12 ...................... 1
38 .............PM2000-238 ............Center Trunnion ................................................... .................................... 1
39 .............PM2000-239 ............Poly-V Belt ........................................................... .................................... 1
40 .............PM2000-240 ............Key ....................................................................... 7x7x25 ........................ 1
41 .............PM2000-241 ............Motor Pulley ......................................................... .................................... 1
42 .............TS-0270031 .............Set Screw............................................................. 5/16-18x3/8................. 4
43 .............PM2000-243 ............Motor Base........................................................... .................................... 1
44 .............PM2000-244 ............Stud...................................................................... .................................... 1
45 .............TS-0680061 .............Flat Washer.......................................................... 1/2 ............................... 2
46 .............TS-0640111 .............Nylon Insert Lock Nut........................................... 1/2-13.......................... 2
47 .............TS-0070031 .............Hex Cap Screw .................................................... 1/2-13x1-1/2................ 1
48 .............PM2000-248 ............Motor ................................................................... 3HP, 230V, 1Ph .......... 1
.................PM2000-MF .............Motor Fan (not shown)......................................... .................................... 1
.................PM2000-MFC...........Motor Fan Cover (not shown) .............................. .................................... 1
.................PM2000-CS .............Centrifugal Switch (not shown) ............................ .................................... 1
.................PM2000-SC .............Starting Capacitor (not shown) ............................ 250MFD, 250VAC....... 1
.................PM2000-RC .............Running Capacitor (not shown) ........................... 20µF, 450VAC ............ 1
.................PM2000-SCC...........Starting Capacitor Cover (not shown).................. .................................... 1
.................PM2000-RCC...........Running Capacitor Cover (not shown)................. .................................... 1
.................PM2000-JB ..............Junction Box (not shown)..................................... .................................... 1
31
Trunnion & Motor Assembly Parts List

Index No. Part No. Description Size Qty


.................PM2000-JBC............Junction Box Cover (not shown) .......................... .................................... 1
.................PM2000-248A ..........Motor ................................................................... 5HP, 230V, 1Ph .......... 1
.................PM2000-MF .............Motor Fan (not shown)......................................... .................................... 1
.................PM2000-MFCA ........Motor Fan Cover (not shown) .............................. .................................... 1
.................PM2000-CSA ...........Centrifugal Switch (not shown) ............................ .................................... 1
.................PM2000-SCA ...........Starting Capacitor (not shown) ............................ 400MFD, 250VAC....... 1
.................PM2000-RCA...........Running Capacitor (not shown) ........................... 35µF, 450VAC ............ 1
.................PM2000-SCCA ........Staring Capacitor Cover (not shown)................... .................................... 1
.................PM2000-RCCA ........Running Capacitor Cover (not shown)................. .................................... 1
.................PM2000-JBA............Junction Box (not shown)..................................... .................................... 1
.................PM2000-JBC............Junction Box Cover (not shown) .......................... .................................... 1
.................PM2000-248B ..........Motor ................................................................... 5HP, 230/460V, 3Ph ... 1
.................PM2000-MF .............Motor Fan (not shown)......................................... .................................... 1
.................PM2000-MFCA ........Motor Fan Cover (not shown) .............................. .................................... 1
.................PM2000-JB ..............Junction Box (not shown)..................................... .................................... 1
.................PM2000-JBC............Junction Box Cover (not shown) .......................... .................................... 1
49 .............PM2000-249 ............Shaft..................................................................... .................................... 1
50 .............PM2000-250 ............Retaining Ring ..................................................... .................................... 1
51 .............PM2000-251 ............Shoulder Screw.................................................... .................................... 4
52 .............PM2000-252 ............Extension Support Bracket .................................. .................................... 1
53 .............TS-0680031 .............Flat Washer.......................................................... 5/16 ............................. 2
54 .............PM2000-254 ............Bearing Arm ......................................................... .................................... 1
55 .............PM2000-255 ............Gear Block ........................................................... .................................... 1
56 .............TS-0680041 .............Flat Washer.......................................................... 3/8 ............................... 3
57 .............TS-0060071 .............Hex Cap Screw .................................................... 3/8-16x1-1/2................ 1
58 .............TS-0060091 .............Hex Cap Screw .................................................... 3/8-16x2...................... 1
59 .............TS-0255041 .............Button Head Socket Screw .................................. 5/16-18x3/4................. 4
60 .............PM2000-260 ............Blade Dust Chute................................................. .................................... 1
61 .............PM2000-261 ............Arbor Nut.............................................................. .................................... 1
62 .............PM2000-262 ............Arbor Collar .......................................................... .................................... 1
63 .............PM2000-263 ............Spring................................................................... .................................... 1
64 .............PM2000-264 ............Arbor .................................................................... .................................... 1
.................PM2000-AA..............Arbor Assembly (Index #61, #62, #64, #78 thru #80)
65 .............PM2000-265 ............Fixed Plate ........................................................... .................................... 1
66 .............PM2000-266 ............Riving Knife Extension Plate................................ .................................... 1
67 .............PM2000-267 ............Clamping Block ................................................... .................................... 1
68 .............PM2000-268 ............Clamping Block .................................................... .................................... 1
69 .............PM2000-269 ............Lock Handle ......................................................... .................................... 1
70 .............PM2000-270 ............Locking Pin........................................................... .................................... 1
71 .............PM2000-271 ............Roll Pin ................................................................ .................................... 1
72 .............PM2000-272 ............Rear Trunnion ...................................................... .................................... 1
73 .............TS-0271051 .............Set Screw............................................................. 3/8-16x1/2................... 1
74 .............TS-081C032.............Pan Head Screw .................................................. #10-24x1/2.................. 4
75 .............PM2000-275 ............Plate ..................................................................... .................................... 1
76 .............PM2000-276 ............Arbor Lock Insert.................................................. .................................... 1
77 .............PM2000-277 ............Spring................................................................... .................................... 1
78 .............PM2000-278 ............Bushing ................................................................ .................................... 1
79 .............BB-6204VV ..............Ball Bearing.......................................................... 6204VV ....................... 2
80 .............PM2000-280 ............Bushing ................................................................ .................................... 1
81 .............PM2000-281 ............Arbor Pulley.......................................................... .................................... 1
82 .............TS-0640091 .............Nylon Insert Lock Nut........................................... 3/8-16.......................... 1
83 .............PM2000-283 ............Shaft..................................................................... .................................... 1
84 .............BB-6003ZZ...............Ball Bearing.......................................................... 6003ZZ........................ 1
85 .............PM2000-285 ............Stop Block ............................................................ .................................... 1
86 .............PM2000-286 ............Washer................................................................. .................................... 1
87 .............PM2000-287 ............Bushing ................................................................ .................................... 1
32
Trunnion & Motor Assembly Parts List

Index No. Part No. Description Size Qty


88 .............PM2000-288 ............DU Bushing .......................................................... .................................... 1
89 .............PM2000-289 ............Retaining Ring ..................................................... .................................... 1
90 .............PM2000-290 ............Retaining Ring ..................................................... .................................... 1
91 .............TS-0720081 .............Lock Washer ........................................................ 5/16 ............................. 2
92 .............PM2000-292 ............Switch Plate ......................................................... .................................... 1
93 .............PM2000-293 ............Magnetic Switch................................................... 3HP, 230V, 1Ph .......... 1
.................PM2000-293A ..........Magnetic Switch................................................... 5HP, 230V, 1Ph .......... 1
.................PM2000-293B ..........Magnetic Switch................................................... 5HP, 230V, 3Ph .......... 1
.................PM2000-293C..........Magnetic Switch................................................... 5HP, 460V, 3Ph .......... 1
94 .............PM2000-294 ............Strain Relief.......................................................... .................................... 2
.................PM2000-294A ..........Strain Relief (for 5HP/1Ph only)........................... .................................... 1
95 .............PM2000-295 ............Power Cord (for 3HP/1Ph) ................................... .................................... 1
.................PM2000-295A ..........Power Cord (for 5HP/1Ph) ................................... .................................... 1
.................PM2000-295B ..........Power Cord (for 5HP/3Ph) ................................... .................................... 1
96 .............PM2000-296 ............Motor Cord (for 3HP/1Ph) .................................... .................................... 1
.................PM2000-296A ..........Motor Cord (for 5HP/1Ph) .................................... .................................... 1
.................PM2000-296B ..........Motor Cord (for 5HP/3Ph) .................................... .................................... 1
97 .............TS-0270101 .............Set Screw............................................................. 5/16-18x1-1/4.............. 2
98 .............PM2000-298 ............Safety Key for Magnetic Switch ........................... .................................... 1
99 .............PM2000-299 ............Bearing Washer ................................................... .................................... 2
100 ...........BB-6805ZZ...............Ball Bearing.......................................................... 6805ZZ........................ 1
101 ...........TS-0271091 .............Set Screw............................................................. 3/8-16x1...................... 1
102 ...........TS-0254022 .............Button Head Socket Screw .................................. 1/4-20x1/2................... 2

33
Trunnion & Motor Assembly

34
Blade Guard & Miter Gauge Assembly Parts List

Index No. Part No. Description Size Qty


1 ...............PM2000-301 ............Riving Knife ......................................................... .................................... 1
.................PM2000-BGA...........Blade Guard Assembly (Index #2 thru #16, #21, #22) ............................. 1
2 ...............PM2000-302 ............Bushing ................................................................ .................................... 2
3 ...............PM2000-303 ............Blade Guard Body................................................ .................................... 1
4 ...............PM2000-304 ............Blade Guard Side Shield...................................... .................................... 2
5 ...............PM2000-305 ............Linking Plate......................................................... .................................... 4
6 ...............TS-1550041 .............Flat Washer.......................................................... M6 ............................... 8
7 ...............TS-1514021 .............Flat Head Socket Screw ...................................... M6x16 ......................... 8
8 ...............PM2000-308 ............Front Shield.......................................................... .................................... 1
9 ...............PM2000-309 ............Bushing ................................................................ .................................... 1
10 .............PM2000-310 ............Top Sight Shield................................................... .................................... 1
11 .............TS-1541021 .............Nylon Insert Lock Nut........................................... M6 ............................... 8
12 .............TS-081B012.............Pan Head Screw .................................................. #8-32x1/4.................... 2
13 .............PM2000-313 ............Roll Pin................................................................. 5x25 ............................ 1
14 .............PM2000-314 ............Roll Pin................................................................. 5x12 ............................ 2
15 .............PM2000-315 ............Lock Pin ............................................................... .................................... 1
16 .............PM2000-316 ............Roll Pin................................................................. 4x30 ............................ 1
.................PM2000-AKPA.........Anti-Kickback Pawl Assembly (Index #17 thru #22) ................................ 1
17 .............PM2000-317 ............Anti-Kickback Pawl .............................................. .................................... 2
18 .............PM2000-318 ............Pawl Base ............................................................ .................................... 1
19 .............PM2000-319 ............Flange .................................................................. .................................... 2
20 .............PM2000-320 ............Lock Pin ............................................................... .................................... 1
21 .............PM2000-321 ............Spring................................................................... .................................... 2
22 .............PM2000-322 ............E-Clip ................................................................... .................................... 2
.................1791789 ...................Miter Gauge Assembly (Index #23 thru #42) ....... .................................... 1
23 .............PM2000-323 ............Miter Gauge Body ................................................ .................................... 1
24 .............PM2000-324 ............Pin ........................................................................ .................................... 1
25 .............PM2000-325 ............Miter Bar............................................................... .................................... 1
26 .............PM2000-326 ............Guide Washer ...................................................... .................................... 1
27 .............PM2000-327 ............Flat Head Machine Screw.................................... M6x9 ........................... 1
28 .............TS-0050051 .............Hex Cap Screw .................................................... 1/4-20x1...................... 2
29 .............PM2000-329 ............Socket Head Cap Screw...................................... M5x8 ........................... 2
30 .............PM2000-330 ............Support Base ....................................................... .................................... 1
31 .............PM2000-331 ............Knob..................................................................... .................................... 1
32 .............TS-1521011 .............Set Screw............................................................. M4x4 ........................... 1
33 .............PM2000-333 ............Locking Handle .................................................... .................................... 2
34 .............TS-0810012 .............Round Head Screw.............................................. #10-24x1/4.................. 1
35 .............PM2000-335 ............Pointer.................................................................. .................................... 1
36 .............PM2000-336 ............Spring................................................................... .................................... 1
37 .............PM2000-337 ............Gear Shaft............................................................ .................................... 1
38 .............PM2000-338 ............Scale .................................................................... .................................... 1
39 .............PM2000-339 ............Rivet ..................................................................... .................................... 2
40 .............PM2000-340 ............Handle.................................................................. .................................... 1
41 .............TS-0680031 .............Flat Washer.......................................................... 5/16 ............................. 1
42 .............PM2000-342 ............Fence ................................................................... .................................... 1

35
Blade Guard & Miter Gauge Assembly

36
Side Cover Assembly

Index No. Part No. Description Size Qty


.................6827044 ...................PM2000 Motor Cover Assembly (Index #1 thru #9).................................. 1
1 ...............PM2000-401 ............Cover.................................................................... .................................... 1
2 ...............PM2000-402 ............Hinge Pin.............................................................. .................................... 2
3 ...............PM2000-403 ............Bracket ................................................................. .................................... 1
4 ...............PM2000-404 ............Latch Clip ............................................................. .................................... 1
5 ...............PM2000-405 ............Button Head Socket Screw .................................. 1/4-20x1-1/4................ 1
6 ...............TS-0640071 .............Nylon Insert Lock Nut........................................... 1/4-20.......................... 1
7 ...............TS-081C032.............Pan Head Screw .................................................. #10-24x1/2.................. 1
8 ...............TS-069204 ...............Flat Washer.......................................................... #10 .............................. 1
9 ...............TS-0560071 .............Hex Nut ................................................................ #10-24......................... 1

37
Wiring Diagrams

3HP, 230V, 1Phase

Magnetic Switch

Electrical Board

GREEN
BLACK
WHITE

A1

WHITE

BLACK
1L2 3L2 5L3 13NO RED
WHIET
BLACK

WHITE
GREEN

GROUND

YELLOW

BLACK
2T1 4T2 6T3 14NO
YELLOW

LED C
A2

R
GREEN

2T1 4T2 6T3


RED

98 97 96 95

250VAC
250MFD

450VAC
GREEN

20UF
WHITE

BLACK

Motor
GREEN

WHITE
BLACK

38
5HP, 230V, 1Phase

Magnetic Switch

Electrical Board

GREEN
BLACK
WHITE

A1

WHITE

BLACK
1L2 3L2 5L3 13NO RED
WHIET
BLACK

WHITE
GREEN

GROUND YELLOW

BLACK

YELLOW
2T1 4T2 6T3 14NO

C
A2

LED
R
GREEN

2T1 4T2 6T3


RED

98 97 96 95

250VAC
400MFD

450VAC
GREEN

35UF
WHITE

BLACK

Motor
GREEN

WHITE
BLACK

39
5HP, 230V, 3Phase

Magnetic Switch

Electrical Board

GREEN
BLACK
RED
WHITE

A1

WHITE

BLACK
1L2 3L2 5L3 13NO RED
BLACK

WHIET
GREEN

WHITE
RED

GROUND YELLOW

BLACK
2T1 4T2 6T3 14NO

YELLOW C
A2

LED
R
GREEN

RED

2T1 4T2 6T3


98 97 96 95

Z1 Y1 X1 Motor
GREEN
WHITE

BLACK

W2 V2 U2
RED

W1 V1 U1
GREEN

BLACK

WHITE
RED

40
5HP, 460V, 3Phase

Magnetic Switch

Electrical Board

GREEN
BLACK
RED
WHITE

A1

WHITE

BLACK
1L2 3L2 5L3 13NO RED
BLACK

WHIET
GREEN

WHITE
RED

GROUND YELLOW

BLACK

YELLOW
2T1 4T2 6T3 14NO

C
A2

LED
R
GREEN

2T1 4T2 6T3


RED

98 97 96 95

Z1 Y1 X1 Motor
GREEN
WHITE

BLACK

W2 V2 U2
RED

W1 V1 U1
GREEN

WHITE
BLACK

RED

41
Notes

42
Notes

43
WMH Tool Group
2420 Vantage Drive
Elgin, Illinois 60123
Phone: 800-274-6848
www.wmhtoolgroup.com
44

You might also like