Liebherr T264 Specifications

Download as pdf or txt
Download as pdf or txt
You are on page 1of 24
At a glance
Powered by AI
The document discusses the specifications and features of the Liebherr T 264 mining truck, including its gross vehicle weight, payload capacity, safety features, engine options, productivity capabilities, and available optional equipment.

The T 264 is designed with safety as a top priority, adhering to industry standards to diminish risk even under extreme conditions. Features mentioned include dynamic braking and various lighting options.

The T 264 supports multiple engine options with power ratings up to 2,013 kW (2,700 HP). Customers can select an engine to allow the truck to meet productivity targets while minimizing fuel consumption.

Mining Truck

T 264
Gross Vehicle Weight (GVW):
Nominal Payload:

393 t / 433 ton


228 t / 251 ton

T 264
Gross Vehicle Weight (GVW):

393 t / 433 ton

Nominal Payload:

228 t / 251 ton

T 264

Productivity

Customer Support

Liebherr Mining Equipment enables superior productivity


by loading and hauling maximum tonnage in the shortest
amount of time.

Liebherr builds more than just mining equipment; Liebherr


also builds customer partnerships.

Efciency

Safety

Liebherr combines the proven capabilities of previous


models with new features that improve operational
efciency.

Mining demands an ever-vigilant focus on safety, and


Liebherr strictly adheres to industry standards. Liebherr
equipment is designed to diminish risk even under the
most extreme mining conditions.

Reliability

Environment

To maximize equipment reliability, Liebherr combines


manufacturing expertise with superior monitoring and
diagnostic capabilities.

Liebherr optimizes mining equipment for fuel economy,


emission compliance, and extended service intervals.

T 264

Litronic Plus AC drive system


Liebherrs efcient drive system with
high power to ground ratios enables
fast acceleration and high speeds on
grade for increased productivity.

T 264

Productivity
By maximizing payload while minimizing cycle times, Liebherr high-horsepower
equipment effectively moves more tons per hour.

Unmatched performance
The T 264 offers high performance on grade. It combines an efcient Litronic Plus
AC drive system and a high power engine up to 2,013 kW (2,700 HP) to yield higher
speeds on grade. With its efcient hydraulic design and fast cycle times, the T 264
moves more material.

Flexible engine options


The T 264 supports multiple engine options with power ratings up to 2,013 kW
(2,700 HP). With application-specic recommendations from Liebherr, Customers
are able to select the engine that will allow the truck to meet productivity targets
while minimizing fuel consumption.

Drivability
Liebherr is committed to designing mining trucks that operators want to drive.
The T 264 fullls this commitment and promotes driver efciency with its superior
comfort, acceleration and handling.

Loading
This 240-ton class truck is well-matched with a variety of rope-shovels, hydraulic
excavators and wheel loaders. Loading the T 264 with either the Liebherr R 9800
or R 996 B hydraulic excavator offers a highly productive combination.

Extended operation
The T 264 is designed to operate for approximately 24 hours without refueling, dependent
upon application. The extended operation is
supported by its low fuel consumption and
optional 4,920 liter (1,300 gallon) fuel capacity.

T 264

Dynamic braking
The T 264 features high-powered, frictionless
dynamic braking. The AC drive system delivers up
to 3,300 kW (4,425 HP) of electric dynamic braking,
reducing engine loading and fuel consumption.

T 264

Efciency
Efciency is a key ingredient for a successful mining operation. Liebherr mining
equipment enables Customers to enjoy unrivaled performance while reducing
cost per ton.

Litronic Plus technology


Developed and built by Liebherr, the proven Litronic Plus drive system determines
the optimal way to extract power from the diesel engine. Efcient loading of the
engine is critical to minimize fuel consumption and maximize performance.

Serviceability
The T 264 reduces maintenance time by offering ground level service points
whenever possible. This feature allows more time to be spent in operation and
less time spent in the workshop.

Intelligent power usage


Engine power usage is optimized by running auxiliary components such as
pumps, fans and motors only when needed. Fuel is conserved when the engine
is idling and more power is available to accelerate the truck and climb grades
when necessary.

Long life components


Components are built to perform in the most extreme mining conditions in order
to allow more time between overhauls and to reach their maximum operational life.

Wheel motors

Engine / Fuel system

The T 264s AC induction motors


efciently convert electrical power
into mechanical torque.
Fewer electrical losses translate
into higher rimpull forces for faster
cycle times and increased fuel
economy.

The T 264 offers reliable engine options with


the latest fuel injection technology for cleaner
combustion and reduced fuel consumption.
Customers can expect reduced maintenance
and lower fuel costs.

T 264

Frame
The T 264s frame is designed according to
international weld fatigue guidelines, and
is fabricated according to American Welding Society standards. This steel structure
includes cast components in strategic areas
and hollow box rails with fully welded internal
stiffeners. These choices ensure the most
durable, lightweight frame available.

T 264

Reliability
Liebherr draws upon a wealth of experience while incorporating new technologies
into its products to provide Customers with high quality equipment and services.

Quality products
With a long history of hydraulic excavators, haulage trucks and support equipment
operating in the harshest mining environments, Liebherr has a proven record of
providing Customers with reliable products. The T 264s design is based on the
experience gained from millions of operating hours on Liebherr trucks.

Advanced engineering tools


Liebherrs structural design process includes various techniques and advanced
software tools to ensure that the T 264 will perform reliably under the most
demanding operating conditions. Some of the tools include:

Multi-body Dynamic Simulations


3D modeling
Finite Element Analysis (FEA)
Structural Fatigue Life prediction software

Diagnostics
The integrated electronic system monitors, records, and outputs vital truck health
and performance data. Data is stored and available for download to perform
detailed analysis. This system supports predictive maintenance strategies to
minimize unscheduled downtime.
Truck data is readily available to eet dispatch or monitoring systems through a
dedicated port using open communication protocols. This allows Customers the
exibility to choose systems which support their maintenance, operations, and
business process requirements.

Integrated dash display


The monitoring system includes an onboard
30 cm (12) touch-screen display. Intuitive menus
and user-friendly screens provide operators and
technicians with real-time truck information.
In addition to the standard operator screen,
password protected diagnostic screens display
live data such as temperatures and pressures
for detailed troubleshooting.

T 264

Extended component life


Liebherr Mining exchange components enable
Customers to minimize the total lifecycle cost
of owning and operating a Liebherr mining
truck or excavator while maintaining peak
productivity and reliability.
All exchange components are built to OEM
standards, offering same-as-new warranties.

10

T 264

Customer Support
Liebherr is committed to maintaining a full life cycle service organization as well as
a global parts warehousing and remanufacturing network.

Product support
Liebherr product support provides the vital interface between the Customer and
Liebherr. There are different levels of product support available:

Assembly
Maintenance advice
Troubleshooting assistance
Technical expertise

Product support personnel work with Customers from the assembly of a truck
throughout its operating life. Liebherr understands the importance of proper
service and support, and will be there for the life of the equipment.

Product upgrade programs


Liebherr offers component and system upgrades as advances in technology,
innovation in design, and manufacturing improvements become available. The
product upgrades can improve performance, reliability and safety.

Parts support and logistics


Liebherr forecasts parts requirements on a global basis and optimizes inventories
to meet Customers needs. Liebherr offers a 24/7 on-call service to ensure prompt
response.

Training
The Liebherr Mining Training System
provides operator and eld service
technicians with world-class operational
and technical training.
Operator training
Basic and advanced service
technician training
Hands-on troubleshooting training

T 264

11

Operator assist features (optional)

FRONT

Vision system provides the additional


viewing angles around the truck to
eliminate blind spots
Detection system alerts the operator
when an object is in close proximity
to the stationary truck

LEFT

RIGHT

Fatigue system provides real-time


monitoring of the operator for fatigue
and distraction events while the truck
is in motion.
REAR

12

T 264

Safety
Liebherr designs and builds safety into every piece of mining equipment, and is
committed to providing a safe and healthy working environment for the operator
and service personnel.

Operator safety
The T 264 cab is ergonomically designed to be a safe, comfortable and productive
environment for operators. The cab provides maximum visibility and is certied for
roll-over and falling-object protection. All Liebherr trucks offer at least two safety
routes from the cab to the ground.

Service personnel safety


Liebherr mining trucks are equipped with ladders designed for easy engine access.
The low working heights of maintenance areas provide safe and efcient service
access.

Access to the engine and alternator from both sides of the chassis
Ground level lling points for fuel, hydraulic oil, grease and coolant
Hydraulic lters and battery isolation box accessible from ground level
Dual access into axle box for maintenance and inspection
Tie offs for safety harnesses
Centralized access to all cab electrical connections
from the superstructure oor

Operational safety
In order to maintain a safe working environment, the T 264 offers the following
features.

Payload overload warnings


Anti-roll back feature active in forward and reverse
Certied steering and braking accumulators
High visibility LED running and service lights
Emergency stop buttons in cab and at ground level

Stability and control


The advanced Traction Control System with four-wheel
speed sensing capability automatically adjusts torque
to the rear wheels to maximize traction when cornering,
accelerating from a standstill, or traveling down wet or
icy roads. Developed by Liebherr exclusively for mining
trucks, this system enables operators to consistently
maintain steering control and truck stability.

T 264

13

Fewer carbon-based consumables


Liebherrs AC drive technology allows the
T 264 to use fewer consumables compared to similar class trucks. It requires
less service time and reduces the costs
of handling and disposing of waste.

14

T 264

Environment
In order to minimize the impact on the environment, Liebherr designs and builds
mining equipment with the smallest possible environmental footprint.

Low emissions
By partnering with the leading providers of high speed diesel engines, Liebherr is
able to offer engine options for the T 264 with the latest emission technology to
satisfy US EPA emissions requirements.

Fuel efciency
Liebherrs Litronic Plus drive system paired with the latest engine technology
provides excellent fuel economy. Lowering the fuel consumption of the truck eet
can signicantly reduce the carbon footprint of the entire operation.

Component exchange
The Liebherr exchange program extends component life cycles. The program
employs condition-based replacements that reduce unplanned maintenance.
Liebherr also reduces waste by overhauling components using original core parts.

Environmental awareness
Liebherr is committed to the protection of the environment and takes the necessary
steps to meet various regulatory requirements in our manufacturing process to
restrict the use of hazardous substances. This includes the use of alternative
coatings and plating that reduce the overall impact on the environment.

Tire life
Liebherrs independent, double A-Arm
front suspensions minimize lateral
tire forces by keeping it in contact
with the ground over uneven roads or
while turning the truck. Optimized for
reduced wear when the truck is driving
loaded, this suspension arrangement is
designed to get the most useful life out
of each tire.

T 264

15

Technical Data
Engine

Model ______________________________ Cummins QSK 60*


Gross horsepower @
1,900 rpm ** _____________________ 1,864 kW / 2,500 HP
No. of cylinders ________________ 16
Displacement ___________________ 60 l / 3,661 in3
Wet weight _______________________ 8,750 kg / 18,893 lb
Crankcase _______________________ 260 l / 68.8 gal
Cooling system ________________ 757 l / 200 gal
* Standard engine setting is USA/EPA Tier 2 compliant in emission-optimized (EO)
mode. Fuel-optimized mode (FO) is optional for non-emission regulated countries.
** Gross power definition according to SAE J 1995 standard conditions.

Model ______________________________ MTU 16V4000 C23R*


Gross horsepower @
1,800 rpm ** _____________________ 2,013 kW / 2,700 HP
No. of cylinders ________________ 16
Displacement ___________________ 76.3 l / 4,656 in3
Wet weight _______________________ 8,844 kg / 19,498 lb
Crankcase _______________________ 300 l / 79.3 gal
Cooling system ________________ 833 l / 220 gal
* Standard engine setting is USA/EPA Tier 2 compliant in emission-optimized (EO)
mode. Fuel-optimized mode (FO) is optional for non-emission regulated countries.
** Gross power definition according to ISO 3046 (ratings also correspond to
SAE J 1995 standard conditions)
Consult factory for other engine options

Electric Drive System


Control System Liebherr Litronic Plus AC drive system with
IGBT technology
Control box Liquid cooled power components, pressurized cabinet
Traction control Litronic Plus traction control system,
Computer controlled in propel and dynamic
braking, forward and reverse, all wheel
speed sensing
Main alternator AC brushless, direct drive, forced air
cooling
Wheel motors Litronic Plus AC induction motors, forced
air cooling
Gear ratio Standard 32.4 to 1 gear ratio (64 km/h /
40 mph)
Cooling system Variable speed AC motor with twin impeller
radial cooling fans

Braking Systems
Electric dynamic braking, forced air over quiet stainless steel resistor
grids with dry disc service and secondary braking system.
Electric dynamic braking Max: 3,300 kW / 4,425 HP
Full dynamic braking down to zero. Singlepedal, automatic brake blending with service brakes from 0.8 km/hr / 0.5 mph to
zero
Dynamic braking
speed control Operator adjustable, automatically limits
truck speed on downhill grade when set
Adjustable speed limits Automatic speed limits for empty and
loaded truck adjustable for site requirements
Traction control Litronic Plus traction control system.
Computer controlled in propel and dynamic
braking, forward and reverse, all-wheel
speed sensing
Service brakes front Outboard single disc, wheel speed, four
calipers per wheel
Service brakes rear Single disc per side, two calipers per disc,
armature speed
Hydraulic accumulators Separate piston type accumulators:
Front Brake Supply (1 x 27 l / 7.1 gal )
Front Brake Pilot (1 x 4 l / 1 gal)
Rear Brake Supply (1 x 7.6 l / 2 gal)
Rear Brake Pilot (1 x 4 l / 1 gal)
Pump control (7.6 l / 2 gal)
Park brakes Spring applied, pressure released, two
calipers per each rear disc
Filtration Cleanliness level ISO 15/13/11

Steering
Ackermann center point lever system, full hydraulic power steering
with accumulator safety backup. Isolated from dump hydraulic system.
Two double-acting hydraulic cylinders.
Hydraulic accumulator 2 x 88 l / 23.2 gal (Piston type)
Filtration Cleanliness level ISO 15/13/11
Turning radius (ISO 7457)
Tire centerline 15.0 m / 49' 2"
Vehicle clearance radius
(ISO 5010) 16.5 m / 54' 2"

Dump System
Two double-stage, double-acting hoist cylinders with inter-stage and
end cushioning in both directions. Electronic joystick with integrated
engine high-idle switch and full modulating control in both extend and
retract.
Dump angle 49 (45 with optional kick-out switch)
Cycle times 20 seconds Power Extend Power Up
11 seconds Power Retract Power Down
14 seconds Retract to Frame
Remote dump Quick disconnects for external power
dumping (buddy dump) accessible from
ground level
Filtration Cleanliness level ISO 15/13/11

16

T 264

Technical Data
Suspensions System
Front

Weights

Double A-Arm with inclined king pin pivot,


spindle, and nitrogen over oil suspensions
with integral damping
Rear _______________________________ Three bar linkage comprised of triangular
upper link plus two bottom drag links and
nitrogen over oil suspensions with integral
damping
_______________________________

Tires
Tires 46/90 R57 Standard
40.00 R57 Optional
Rims 29" x 57" bolt on rims

Frame
Design Closed box structure with multiple torque
tube cross members, internal stiffeners and
integrated front bumper.
Steel castings are used in high stress areas.
Welding Frame girders welded inside and out with
ultrasonic inspection aligned with AWS
D1.1

Cab
Deluxe cab with integrated ROPS, FOPS, and double wall design for
optimum insulation. Fully adjustable air suspension operator seat
with double lumbar support and full-size second seat for training requirements. Operator comfort controls include a tilt and telescoping
steering wheel, heater, defroster and standard AC. Real-time vital truck
information is easily displayed to the operator and also recorded for
download.

With standard 46/90 R57 tires


Nominal Payload________________ 228 t / 251 ton
Gross Vehicle
Weight (GVW)____________________ 393 t / 433 ton
Chassis weight * ________________ 139 t / 153 ton
Body weight______________________ 26t / 29 ton
Weight distribution______________ Empty front 50 % / rear 50 %
Loaded front 33 % / rear 67 %
* Standard truck (less options), 100% fluids (fuel tanks, hydraulic tank, gears, suspensions, crankcase, coolant, grease and charged accumulators)

With optional 40.00 R57 tires


Nominal Payload________________ 222 t / 244 ton
Gross Vehicle
Weight (GVW)____________________ 385 t / 424 ton
Chassis weight *_________________ 137 t / 151 ton
Body weight______________________ 26t / 29 ton
Weight distribution______________ Empty front 50 % / rear 50 %
Loaded front 33 % / rear 67 %
* Standard truck (less options), 100% fluids (fuel tanks, hydraulic tank, gears, suspensions, crankcase, coolant, grease and charged accumulators)

Fluid Capacities
Fuel tank

3,028 l / 800 gal

Hydraulic system (brake, steering and hoist)


Tank 969 l / 256 gal
System 1,060 l / 280 gal
Planetary gear sets,
each (2) 175 l / 46.2 gal
Front wheels, each (2) 52 l / 13.7 gal
Grease tank 55 kg / 120 lb

Body
Body sizes are custom designed to fit Customer requirements and
specific applications. Please contact factory for options.

Sound
Interior cab noise level
(per ISO 6394:2008) __________ 75 dB(A) sound pressure

T 264

17

Technical Data
Dimensions

J
N

Q
M
K
B
A

T264

T264

D
G
F

C
Dimensions
A
B
C
D
E
F
G

18

Outside Body Width


Overall Truck Width
Centerline Front Tire Width
Bumper Ground Clearance
Crossmember Ground Clearance
Overall Tire Width
Centerline Rear Dual Width

T 264

mm/ft in
7,841 mm / 25'7"
8,621 mm / 28'3"
6,254 mm / 20'5"
1,149 mm / 3'8"
1,036 mm / 3'4"
7,632 mm / 25'0"
3,670 mm / 12'0"

Dimensions
H
I
J
K
L
M
N

Rear Axle Clearance


Front Canopy Height
Overall Truck Length
Wheelbase
Loading Height
Dump Clearance
Body Raised Height

mm/ft in
797 mm / 2' 6"
7,171 mm / 23' 5"
14,197 mm / 46' 6"
6,119 mm / 20' 1"
6,280 mm / 20' 6"
1,321 mm / 4' 3"
14,005 mm / 45'10"

Performance Curves

EVW

16

GVW

Rimpull

14
13
12

600

160

11

9
120

500
100

80

200
100
0

5
60

40

3
2

20

10

10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48

15

20

25

30

35

40

45

50

55

60

65

70

75

mph

80 km/h

Speed

Performance Chart Parameters

600
1350

1400

1250

1300

1150

1100

1200

1050

1000

500

400
850

950

800

900

300
750

700

550

650

600

200
500

350

450

400

100
250

300

18

260

17

EVW

240

16

GVW

15
200

800

180

14
13
12

700
600

160

11

10

140

9
120

500
100

400

80
300
200

5
60

40

3
2

100

20

21
20
19

900

400
300

1000

10

140

22
320

280

17

240

24
23

320

1200
1100

lb

R0179

300

18

260

180

Lbf x 1000

20

15

700

1300

19

800

340

kg

10

10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48

15

20

25

30

35

40

45

50

55

60

65

70

75

mph

80 km/h

Speed

Performance Chart Parameters

Gross Power 1,864 kW / 2,500 HP (A)


Net Power 1,816 kW / 2,435 HP (A)
Tire Size 46/90 R57
Gear Ratio 32.4 to 1
Reference Curves A: Propulsion 1,864 kW / 2,500 HP
B: Dynamic Braking (Retard)

Gross Power 2,013 kW / 2,700 HP (A)


Net Power 1,965 kW / 2,635 HP (A)
Tire Size 46/90 R57
Gear Ratio 32.4 to 1
Reference Curves A: Propulsion 2,013 kW / 2,700 HP
B: Dynamic Braking (Retard)

Note
The propulsion curve is calculated using net horsepower, therefore site
specific and climatic variables will have an effect on the parasitic loss
estimations.

Note
The propulsion curve is calculated using net horsepower, therefore site
specific and climatic variables will have an effect on the parasitic loss
estimations.

Percent effective grade

21

280

200

1500
1400

22
320

900

600
1400

1250

1350

1200

1300

1150

1100

1050

1000

500

400
950

850

900

800

300
750

700

550

650

600

200
500

450

24

1200

1000

360

23

320

300

1100

1600

lb

R0178

Rimpull

1300

GVW x 1000
kg

Percent effective grade

1400

350

340

400

1500

100

360

250

Lbf x 1000

1600

300

GVW x 1000

T 264

19

Loading Charts
m
22

ft
70

20
18
16

60

50

T 264 mining truck loaded by the Liebherr R 996 B


hydraulic excavator in face shovel configuration
Maximum dump height
Truck loading height
Passes to fill
(given a 1.8 t/m3 density at
95% bucket fill factor)

12.9 m/42'3"
6.3 m/20'8"

4 passes

14
12
10

40

30

8
6
4

20

10

2
0

-2
-10
-4
m 0
ft

4
10

20

10

12

30

40

14

16

18

50

60

ft

18

60

16

50

14
12
10
8
6
4
2
0
-2
-4
-6

40
30
20
10
0
-10
-20

-8
m 0
ft 0

20

T 264

4
10

6
20

10
30

12
40

14

16
50

18
60

20

22
65

-30

T 264 mining truck loaded by the Liebherr R 996 B


hydraulic excavator in backhoe configuration
Maximum dump height
Truck loading height
Passes to fill
(given a 1.8 t/m3 density at
95% bucket fill factor)

10.7 m/34'11"
6.3 m/20' 8"

4 passes

Loading Charts
ft
70

m
22

T 264 mining truck loaded by the Liebherr R 9800


hydraulic excavator in face shovel configuration

20
60
50

Maximum dump height


Truck loading height
Passes to fill
(given a 1.8 t/m3 density at
95% bucket fill factor)

18
16
14

40
30

13 m/42'6"
6.3 m/20'8"

3 passes

12
10
8

20
10
0
-10

6
4
2
0
-2
-4
20

18
60

ft

60

18

50

16
50

14

12

10

40

30

20

0 m

2
10

0 ft

T 264 mining truck loaded by the Liebherr R 9800


hydraulic excavator in backhoe configuration

16

Maximum dump height


Truck loading height
Passes to fill
(given a 1.8 t/m3 density at
95% bucket fill factor)

14
40
30
20
10
0
-10
-20
-30

12
10

3 passes

8
6
4
2
0
-2
-4
-6
-8
-10
24 22 20 18 16 14 12 10
80

10.9 m/35'9"
6.3 m/20'8"

70

60

50

40

30

6
20

2
10

0 m
0 ft

T 264

21

Standard Equipment
Standard Equipment
Engine
Air cleaner dust ejectors automatic
Air cleaners two units with 2 elements per unit with electronic
restriction monitoring in cab
Engine roll over protection switch
Exhaust side-mounted mufflers with insulated exhaust pipes
Fan clutch variable speed, temperature controlled
Fuel/water separator
Oil centrifuge filter
Prelube pre-start engine oil pressurization to reduce dry
engine turnover
Primary and secondary fuel filters
Radiator L & M (Mesabi) flexible core, with center-mounted
level gauge on front face of surge tank
Roll out power module engine, main alternator and hydraulic pump
directly mounts to frame using removable tool system
Starter electric
24 V Electrical
Batteries 6 x 12 Volt (3 series of 2), 1,300 CCA each at -18C
(0F, 1,560 CCA at 0C (32F)
Battery box lockouts ground level, battery, propel and starter
(single pole)
Electrical system 24 VDC with circuit breaker protection
Engine Shutdown Switch in-cab and ground level
Operator Environment
Climate control combined heater and air conditioner w/multiple
air ducts and filtered air
Cup holder 2 center console mounted
Diagnostics interface CANopen, Ethernet, Wi-Fi, USB
Display screen dimmable color touch screen w/operator
information and warning
Dual overhead LED dome lights that illuminate when the door is opened
Integrated ROPS (ISO 3471:2008) and FOPS (ISO 3449:2005, Level II)
Mirrors drivers side (flat), offside (convex) and access ladder (convex)
Power outlets 2 x 120V AC
Power windows driver and passenger
Pressurized cab with fan on
Radio ready wiring, speakers and DIN fitting
Seat belt high visibility orange 3 point 2 inch wide
Seats fully adjustable driver and passenger heated seats
with air suspension
Speedometer km/h / mph
Steering wheel tilting and telescopic with horn and wiper control
Storage shelves and storage compartment located behind seats
Sun visors 2 windshield sun visors and 1 drivers door pull down blind
Windows tempered and tinted glass 6.3 mm
Windshield laminated safety glass and tinted 9.5 mm
Wipers two speed electric and intermittent with dual wiper arms

22

T 264

AC Drive System and Controls


Anti-roll back in forward and reverse
Brakes dynamic braking w/automatic hydraulic brake blending
and hydraulic service brakes
Gear assembly Liebherr gears and wheel motors
Gear ratio 32.4:1
Grid box resistor grid control system and constant AC grid box
blower motor
Litronic Plus control cabinet IGBT technology, liquid cooled,
pressurized, filtered air inlet, ground fault warning and detection
Traction control system with four-wheel speed sensing
Lighting
Access lights 3 ladder, 1 superstructure
Brake warning lights (cab mounted external) forward facing retard
and service brake (LED)
Headlights 4 x high beam, 4 x low beam (LED)
Reverse lights 2 x axle box, 1 x drivers side superstructure (LED)
Service lights 2 x engine bay, 2 x axle box (LED)
Truck lights tail, brake, retarder and clearance/directional indicators
Other
Access ladders 45 diagonal stair (drivers side access)
with two side ladders w/flexible step
Accumulators (Certified)
Steering (2 x 88 l / 23.2 gal) Rear Brake Supply (1 x 7.6 l / 2 gal)
Front Brake Supply (1 x 27 l / 7.1 gal ) Rear Brake Pilot (1 x 4 l / 1 gal)
Front Brake Pilot (1 x 4 l / 1 gal) Pump control (7.6 l / 2 gal)
Axle box dual entry service access and rear air exhaust
Centralized service station ground level, driver side, with fuel
gauge and pressureless fast fill system.
Color white / gray
Fall protection multiple personnel tie off points
Fluid sampling multi-sampling ports close to components
Grease system automatic lubrication system
Hydraulic coolers 1 x hoist system, 1 x HVAC system,
2 x final drive gear oil
Hydraulic filters high pressure for brake, steering and hoist
w/electronic monitoring
LED payload display 2 x superstructure mounted
Mud flaps front and rear of fuel tanks, superstructure and
battery control box
Park brake spring applied pressure release
Recovery system auxiliary connectors for brake, steering and hoist
buddy system
Reverse alarm
Rims bolt on, 2 x double gutter, 4 x single gutter
Rock ejectors bar type
Service access ladders right and left engine bay ladders
w/ flexible steps
Shut off valves brake/steering and hoist w/electronic monitoring
Sight gauges hydraulic tank, radiator, control box and front wheel hub
Towing points front, rear and center tow haul receptacle

Optional Equipment
Optional Equipment
Access stair powered retractable stair to main diagonal stairway
*Advanced camera system multi-view, integrated into dashboard
touchscreen
Battery box lockouts ground level, battery (double pole),
propel and starter (single pole)
Blue Truck identifier light (power on) grill mounted
Brake covers 2 x front wheel
Centered dashboard gauge panel in metric and imperial
Cold climate diesel type engine heater, w/automatic control
Color Liebherr yellow / grey
Curb / berm cornering lights (LED) forward facing, superstructure
mounted (DS and ODS)
Dump body liners, heated, tailgates, rock deflectors
Dump body raise limit 45 kick out switch
*Fatigue monitoring system
Fire suppression systems
Fog lights (HID) 4 x bumper mounted
Fuel tanks (4,921 l / 1,300 Gal)
Grill illumination light (LED)
Heated mirrors

*High altitude package (HAP)


Hill cresting lights (LED) 2 x top grill mounted
Hydraulic return line filtration (3 x hydraulic filters)
Multiple language decals
Overspeed light externally mounted blue strobe on top of cab
Park brake off / truck in neutral warning light (LED)
externally mounted on top of cab
*Proximity awareness camera and radar system integrated into
dashboard touchscreen
Quick fill connection (Fuel) 568 lpm / 150 gpm, 757 lpm / 200 gpm
Reverse light (LED) off drivers side superstructure
Rock ejectors chain type
Service lights 2 x rear engine bay
*Sound attenuation package
*Trolley capable
Undercarriage protection engine belly pans

Standard and optional equipment are subject to change at


manufacturers discretion.
Please contact your local representative for further information.
*Consult factory for further details

T 264

23

WideProductRange

State-of-the-artTechnology

The Liebherr Group is one of the largest construction


equipment manufacturers in the world. Liebherrs
highvalue products and services enjoy a high reputation
in many other fields. The wide range includes domestic
appliances, aerospace and transportation systems,
machine tools and maritime cranes.

To provide consistent, top quality products, Liebherr


attaches great importance to each product area, its
components and core technologies. Important modules
and components are developed and manufactured
inhouse, for instance the entire drive and control
technologyfor construction equipment.

ExceptionalCustomerBenefit

WorldwideandIndependent

Every product line provides a complete range of models


in many different versions. With both their technical
excellence and acknowledged quality, Liebherr products
offer a maximum of customer benefits in practical
application.

Hans Liebherr founded the Liebherr family company in


1949. Since that time, the enterprise has steadily grown
to a group of more than 130 companies with over
38,000employees located on all continents. The corporate
headquarters of the Group is LiebherrInternational AG
inBulle, Switzerland. The Liebherr family is the sole owner
of the company.

www.liebherr.com

Liebherr Mining Equipment Newport News Co.


4100 Chestnut Avenue, Newport News, VA 23607, USA
+1 (757) 245 5251, Fax +1 (757) 928 8755
www.liebherr.us, E-Mail: [email protected]
www.facebook.com/LiebherrConstruction

Printed in Germany by Eberl BK-RP LME 11481629-0.85-02.14_enGB


All illustrations and data may differ from standard equipment. Subject to change without notice.

TheLiebherrGroupofCompanies

You might also like