Monitor GE 1900 - 65A

Specifications and Ordering Information
1900/65A General Purpose Equipment Monitor

Description
The 1900/65A General Purpose Equipment Monitor is a machinery vibration
monitor designed to continuously monitor and protect equipment that are used in a
variety of applications and industries. The low cost of the 1900/65A makes it an
ideal solution for general-purpose machines and processes that can benefit from
continuous monitoring and protection.
Inputs
The 1900/65A provides four transducer inputs and four temperature inputs.
Software can configure each transducer input to support 2- and 3-wire
accelerometers, velocity sensors or proximity sensors. Each temperature input
supports Type E, J, K, and T thermocouples, and 2- or 3-wire RTDs.
Outputs
The 1900/65A provides six relay outputs. The user can configure the contacts of
these relays to open or close according to the OK, Alert and Danger statuses of any
channel or combination of channels.
The monitor provides four 4-20 mA recorder outputs. Software can configure each
recorder output to output any variable from any channel.
The signal for each transducer input is also available on a dedicated buffered
output.
A Modbus Gateway option is available. This allows the monitor to serve static
variables, statuses, event list, time and date information directly to any Modbus
client, including Distributed Control Systems (DCSs), Supervisory Control and Data
Acquisition (SCADA) systems, Programmable Logic Controllers (PLCs) or System
1. The monitor uses an internal counter and a time reference sent from the
Modbus client/master to generate time and date information. Users can upgrade
monitors ordered without the Modbus Gateway by ordering the 1900/01
Communications Upgrade (see the Ordering Information section). The 1900/65A
provides Modbus via Ethernet and a software-configurable 232/485 serial port.
Configuration
The user defines monitor operation and the Modbus Gateway register map by
creating a configuration file using software running on a laptop or PC and
downloading the file to the monitor through the built-in Ethernet connection. The
1900/65A permanently stores configuration information in non-volatile memory, and
can upload this information to the PC for changes.
Display Module
An optional display/keypad for viewing channel information or making minor
configuration changes allows the 1900/65A to operate as a stand-alone package. If
desired, the user can mount the display up to 75 metres (250 feet) from the Monitor
Module.
FOR REFERENCE ONLY

REFER TO DOCUMENT #173401
Page 1 of 18
kind of variables or measurement

values that will be derived from this
input. Channel Types also define the
kind of sensor that must be used.
Transducer Channel Types include:
Feature List
Continuous monitoring and protection is suitable for

auto-shutdown applications
Stand-alone operation on general-purpose equipment
Optional Modbus communications via

10BaseT/100BaseTX Ethernet, or
software-configurable 485/232 serial port
Acceleration or Reciprocating
Acceleration
Velocity or Reciprocating Velocity
Small package. Monitor Module: 196.9 mm x 149.4

mm x 74.4 mm (7.75 x 5.88 x 2.93). Monitor
Module with attached Display Module: 196.9 mm x
149.4 mm x 97.8 mm (7.75 x 5.88 x 3.85)
Radial Vibration (shaft vibration)
Thrust (shaft axial displacement)
Position
DIN rail or bulkhead mounting options
Speed
18 to 36 Vdc power input. (optional 110-220 Vac

external supply)
24-bit ADC conversion
Four vibration/position/speed inputs
Four temperature inputs
Configurable scale factors and full scale ranges
Up to four processed variables per channel with

independent integration and filter control
Internal OK checking with status
Independent Alert and Danger setpoints
200-entry event list
Six relay outputs. Relay operation is programmable
Buffered outputs for each transducer channel
Four configurable 4-20 mA recorder outputs
Optional NEMA 4X/IP66 fiberglass housing with

window for display
Painted or stainless steel weatherproof door for panelmount display
Hazardous area approvals
Acceleration and
Reciprocating
Acceleration
Channel Types
Acceleration
Variables and
Reciprocating
Acceleration
Variables
Vibration:
Acceleration
Enveloping:
Specifications
Inputs
Transducer Inputs
Users can configure Channels 1
through 4 to accept input from
acceleration, velocity or displacement
transducers.
Acceleration Variables and

Reciprocating Acceleration Variables
are filtered and processed
measurements from raw transducer
signals. The Acceleration Channel
Type and Reciprocating Acceleration
Channel Type continuously processes
up to four variables per channel.
Up to three bandpass filtered amplitude
measurements.
Users can apply the acceleration

enveloping algorithm to one
Acceleration or Reciprocating
Acceleration Variable.
Bias Voltage:
Transducer Channel Types

Channel Types define the
functionality for processing that will
be applied to an input signal and the
FOR REFERENCE ONLY
The Acceleration Channel Type and

Reciprocating Acceleration Channel
Type support two- and three-wire
acceleration sensors. The
Reciprocating Acceleration channel
type has timed OK channel defeat
disabled.
Users may assign the value of the

transducer bias voltage to any of the
variables.
Page 2 of 18
Configuration
Options
Vibration
Variables:
Integrated:
Each variable is independently
configured with the following options.
Accuracy
Vibration
Variables:
Peak or RMS
Metric or English units
Filter corner frequencies
Full scale range
Acceleration integrated to velocity
Enveloped
Variable:

Standard or Enhanced demodulation
Filters
Vibration
Variable:
Enveloping
High-Pass:
Enveloping
Low-Pass:
Enveloped
Variable HighPass:
0.5 Hz 25 kHz configurable 4-pole

high-pass, 4-pole low-pass
Velocity and
Reciprocating
Velocity Channel
Type
Velocity Variables
and Reciprocating
Velocity Variables
125 Hz to 25 kHz, configurable

2-pole
0.1 Hz min., but greater than

Enveloped Variable low-pass 2-pole
Vibration:
Bias Voltage:
Greater than Enveloped Variable
high-pass and less than Enveloping
high-pass 4-pole
OK Filter:
Input Impedance
3-wire Voltage
Mode:
25 Hz to 5 kHz, configurable 4-pole
Enveloped
Variable LowPass:
Bias Filter:
Bias Voltage:
0.01 Hz 1-pole low-pass
-24 V
1% of full scale range
10 k
The Velocity Channel Type and

Reciprocating Velocity Channel Type
support two-wire and three-wire piezovelocity sensors.
Velocity Variables and Reciprocating

Velocity Variables are filtered and
processed measurements from raw
transducer signals. The Velocity
Channel Type and Reciprocating
Velocity Channel Type support up to
four continuously calculated variables
per channel.
Up to three bandpass filtered amplitude
measurements.
Users may assign the value of the
transducer bias voltage to any of the
variables.
Configurable Options
Vibration
Variables:
2.4 kHz 1-pole low-pass
Peak or RMS
Full Scale Range

Vibration:

20 to 500 m/s2 (2 to 50 g) peak and
RMS
Enveloped:
10 to 100 mm/s (0.4 to 4 in/s) peak and

RMS
20 to 500 m/s2 (2 to 50 g) peak and

RMS
FOR REFERENCE ONLY


Full scale range
Velocity integrated to displacement
Page 3 of 18
Vibration
Variables:
Filters
Vibration
Variables:
0.5 Hz to 5.5 kHz, configurable
8-pole high-pass, 4-pole low-pass
Bias Filter:
OK Filter:
Full scale range

Filters
Direct Filter 1:
10 to 50 mm/s (0.5 to 2 in/s) peak

and RMS
Bias Voltage:
Accuracy
Vibration
Variables:
Input Impedance
3-Wire Voltage
Mode:
Radial Vibration
Channel Type
Radial Vibration
Variables

Number of filter poles
Full Scale Range

Vibration:
Integrated:
100 to 500 m (5 to 20 mils) peak to

peak
Direct Filter 2:
Direct Filter
Characteristics:
Gap Filter:
-24 V
4 to 4000 Hz (240 to 240,000 RPM)

1 to 600 Hz (60 to 36,000 RPM)
High-pass set by attack and decay,

1-pole low-pass
Vibration
Variables:
0.5 Hz to 4 kHz, configurable
1-, 2-, or 4-pole high-pass and lowpass, configurable

OK Filter:
10 k
Full Scale Range
Direct:
The Radial Vibration Channel Type
measures radial shaft motion using
proximity sensors.
Radial Vibration Variables are filtered

and processed measurements from
raw transducer sensors. The Radial
Vibration Channel Type supports up
to four continuously calculated
Variables per channel.
Gap:
Accuracy
Vibration
Variables:
Input Impedance
Non-configurable:
Direct:
100 to 500 m (3 to 20 mils) peak-topeak

-24 V
10 k
Up to three bandpass filtered

amplitude measurements
Gap:
Vibration:
Configurable
Options
Gap voltage
Up to three bandpass filtered
amplitude measurements

FOR REFERENCE ONLY

Page 4 of 18
Thrust Channel
Type
Thrust Variables
Position:
Gap:
Position:
The Thrust Channel Type measures
axial shaft motion using proximity
sensors.
Gap:
Gap, voltage or position
Configurable Options
Thrust Variables are filtered and

transducer signals.
Position
Variables:
Axial position of shaft

Gap, voltage or position
Filters
Direct Filter:

Position
Variables:
Filters
Direct Filter:
1 to 28 mm (50 to 1100 mils) span with

adjustable zero position
-24 V
Accuracy
Position
Variables:
Input Impedance
Nonconfigurable:
Gap:
OK Filter:
Accuracy
Position
Variables:

Full Scale Range

Position:
Full scale range
Gap:
Gap Filter:
OK Filter:
Full Scale Range

Position:

Full scale range
Configurable
Options
Gap Filter:
Mechanical position
1 to 4 mm (50 to 150 mils) span with

adjustable zero position
Input Impedance
Non-configurable:
Speed Channel
Type
24 V
Speed Variables
10 k
The Speed Channel Type measures

speed using proximity sensors.
Speed Variables are filtered and
transducer signals.
Speed:
Up to four speed measurements
10 k
Gap:
Position Channel
Type
Gap, voltage
The Position Channel Type

measures mechanical motion using
proximity sensors.
Position Variables
Position Variables are filtered and
transducer signals.
FOR REFERENCE ONLY
Page 5 of 18
Configurable
Options
Gap Filter:
Type J:
OK Filter:
Events Per
Revolution
EPR:
Accuracy
Speed
Variables:
Input Impedance
Nonconfigurable:
-200 to 1370 C (-328 to 2498 F)
10 Cu
=0.00427:

Full Scale Range
Speed:
Type K:
Type T:
Configurable
Options
Units:
Filters
Analog Filter:
-200C to 260 C (-328 to 500 F)
-80C to 260 C (-112 to 500 F)

100 Pt
=0.00385:
0.001 to 1000
100 Pt
=0.00392:
0.5 RPM + 0.015% of reading
Accuracy
All Thermocouple
Types:
10 k
Temperature variables are processed

measurements from raw transducer
signals. The temperature channel
type processes one temperature
variable per channel.
Each Variable is independently

C or F
Notch filter will attenuate the first

5 orders of 50 Hz and 60 Hz (49
Hz to 61 Hz) by a minimum of
100 dB.
-200 to 850 C (-328 to 1562 F)
-200C to 700 C (-328 to1292 F)
1 C (1.8 F) typical @ 25 C (77

F)
2.5 C (4.5 F) maximum for
thermocouple measurements over
100 C (148 F)
5 C (9 F) maximum for
thermocouple measurements below
100 C (-148 F)
3-Wire RTD
(except 10
Cu):
3-Wire RTD 10
Cu:
2-wire RTD
Types:
50 Hz 1-pole, low-pass
Digital Filter:
Full Scale Range

Type E:
-200 to 400 C (-328 to 752 F)
120 Ni
=0.00672:
100 - 100,000 rpm
Temperature Inputs (Ch. 5 8)

Channels 5 through 8 support Type
E, J, K, and T thermocouples, and 2and 3-wire RTDs.
Temperature
Variable
-210 to 1200 C (-346 to 2192 F)
Input Impedance
Thermocouple
Inputs:
1.5 C (2.7 F) + 0.5 % full scale
3 C (5.4 F) + 0.5 % full scale
2-wire RTDs have additional errors due

to field wire resistance and variations in
the field wire resistance due to
changes in ambient temperature.
>1 M
-200 to 1000 C (-328 to 1832 F)
FOR REFERENCE ONLY

Page 6 of 18
Alarm Status Time Delays
Maximum Operands
Position / Vibration Inputs

Minimum
0.1 second
Relay Configuration
Maximum
Adjustment
Resolution
The following configuration options are

independent of the relay logic and can
be configured for each relay:
60 seconds
Latching or non-latching
independent of alarm status
0.1 second
Normally energized or normally deenergized
Temperature / Speed Inputs

Minimum
1 second
Maximum
Adjustment
Resolution
50 per relay
Normally open and normally closed

via contacts
60 seconds
Relay Specifications
Type
Single pole, double throw (SPDT)
0.1 second
Maximum Contact
Voltage
Relays
300 Vrms
150 Vdc
Relay Logic
The 1900/65A monitor has six relay
outputs that users can program to
open or close contacts according to
user-defined logic statements. Logic
statements use the OK, Alert and
Danger statuses of any channel, or
combination of channels as inputs.
Minimum Switched
Current
Maximum Switched
Power
100 mA @ 12 Vdc
160 W dc
1500 VA ac
Contact Life
100,000 cycles @ 5 A, 250 Vac
Logical Operators
200,000 cycles @ 1 A, 24 Vdc

AND (bypassed channels ignored)
True AND (bypassed channels
included)
OR
Logical Operands
Sealing
Insulation
Resistance
Epoxy
1000 M minimum @ 500 Vdc
Monitor inhibit
Monitor Not OK
Monitor Danger
Monitor Alert
Channel Not OK
Channel Danger
Channel Alert
Variable Danger
Variable Alert
FOR REFERENCE ONLY

Page 7 of 18
Electrical
Activate Reset
Inhibit, Reset, and Trip Multiply Inputs

Inhibit/Trip Multiply
Users can use software to configure
the Inhibit/Trip Multiply input as either
Inhibit or Trip Multiply.
When configured for Trip Multiply
short-circuiting the Inhibit/Trip
Multiply contact to RTN will increase
Alert and Danger set points.
When configured for Inhibit the Inhibit
input will inhibit (bypass or inactivate)
Alert and Danger statuses. Short
circuiting the INHIBIT contact to
INHIBIT RTN will:
Set all Variable Danger Statuses
to logic 0
Set all Variable Alert Statuses to
logic 0
Set Bypass and Inhibit Statuses to
logic 1
Modbus Note: Monitor Alarm Inhibit
switch, and Monitor Trip Multiply
switch mapped in the Modbus
Gateway will remotely inhibit Alert
and Danger statuses or activate Trip
Multiply respectfully.
Electrical
Activate Inhibit
De-activate Inhibit
50 k or less (shorted)
De-activate Reset
All outputs are short-circuit protected.

Two-Wire Current Mode
Current Source
3.3 mA 5%
Open Circuit
Voltage
Reset all latched Alert statuses

Reset all latched Danger statuses
Maximum Rated
Current
15 mA
Short Circuit
Current
Number of Outputs
Loop Supply
Voltage
Loop Resistance
Accuracy
Update Rate
Resolution
Modbus Note: Writing a non-zero

value to the Modbus register Reset
Latched Statuses mapped in the
Modbus Gateway will reset the
monitor remotely.
FOR REFERENCE ONLY

15.1 mA to 23.6 mA
4-20 mA Interface
Reset all latched Not OK statuses

Reset all latched relays
21 to 24 Vdc
Three-Wire Voltage Mode

Supply Voltage
-24.02 Vdc to 23.47 Vdc
500 k or greater (open)

Use the Reset input to reset all
latched alarms and latched relays. If
the condition driving the status no
longer exists, short circuiting the
RESET contact to RESET RTN will:
500 k or greater (open)
Transducer Supplies
Proportional Value
Reset
50 k or less (shorted)
Four outputs, any of which may be

configured to provide data from any
channel and any variable.
4 to 20 mA values are proportional to
the channel full-scale.
18 to 36 Vdc
600 maximum
2% over operating temperature range
100 mS
10 A
Clamp Current
2 mA 10% (configurable for Not OK

and Bypass)
Page 8 of 18
Display
Buffered Outputs
Display Module
A single buffered output on the
Display Module provides access to
input Channels 1 through 4. The
signal does not have gain, and is not
scaled. This output is buffered to
provide short circuit and EMI
protection.
Power Requirements
550
Operating Current
40 kHz minimum (Display Module

attached directly to Monitor)
Operating Power
8 kHz minimum (75 m (250 ft.) of

cable)
Physical
Output Impedance
Bandwidth
68.6 mm (2.7 in) wide x 35.6 mm (1.4

in) high
Input Voltage
Range
Each input for channels 1 through 4

has a dedicated buffered output. The
signal does not have gain, and is not
scaled. Each output is buffered to
provided short circuit and EMI
protection.
196.9 mm x 149.4 mm x 74.4 mm

(7.75 in x 5.88 in x 2.93 in)
Weight
40 kHz minimum
Weight
Mounting
DIN Rail Option
Indicates when the monitor is

functioning properly
Bulkhead Option
Indicates when the monitor is
functioning properly
Weatherproof
Enclosure Option
Alert LED
Indicates an Alert condition
Danger LED
Bypass LED
Trip Multiply LED
Channel LED
0.77 kg (1.70 lb)
196.9 mm x 149.4 mm x 32.8 mm

(7.75 in x 5.88 in x 1.29 in)
Indicators
Display Module
OK LED
8.5 W typical, 14 W maximum
Monitor Module
Dimensions (L x W
x H)
Display Module
Dimensions (L x W
x H)
550
Bandwidth
Monitor Module
Status LED
18 to 36 Vdc
0.35 A typical, 1.0 A maximum
Monitor Module
Output Impedance
Liquid Crystal Display (LCD) with

backlight
Indicates a Danger condition
0.40 kg (0.89 lb)
35 mm DIN rail
Bulkhead mounting plate
NEMA 4X/IP66 Fiberglass Housing

with window, 300.2 mm x 249.4 mm x
209.8 mm (11.82 in x 9.82 in x 8.26 in)
Indicates that the monitor is in

Bypass mode
Indicates that the monitor is in Trip
Multiply mode
Indicates channel is active
FOR REFERENCE ONLY

Page 9 of 18
10/100BaseT Ethernet interface (10

or 100 Mb/s)
Software
The 1900 Configuration
Software package contains
everything necessary to install,
configure, and maintain the 1900/65A
monitor.
Features
1024 x 768 screen resolution

recommended
Environmental
Temperature
Operating
Tools for installing and

troubleshooting
-20 to +70 C
(-4 to +158 F)
Simple display to help with

configuration
Storage
-30 to +90 C
Ability to browse network for 1900

monitors
Network configuration
Configuration for channels,
variables, setpoints, tag names,
recorders and filters
Configuration for the optional
Modbus Gateway
Configuration for relays and relay
voting logic
Off-line configuration allowing use
of software when hardware is not
available
Firmware upgrade function and
diagnostics
Change bypass modes and
setpoints on the fly
(-22 to +194 F)
Humidity
Operating
95% non-condensing, maximum
Storage
Supported Transducers
Channel Type
Bently Nevada Transducer
Acceleration and
Reciprocating
Acceleration
200350 Accelerometer
Velocity and
Reciprocating Velocity
190501 Velomitor
330500 Velomitor
330525 Velomitor
330750 Velomitor
Radial Vibration,
Thrust, and Speed
3300 5 & 8 mm Proximitor

System
3300 XL 8mm Proximitor System
3300 XL NSvTM Proximitor System
7200 5 & 8mm Proximitor System
7200 11mm Proximitor System
7200 14 mm Proximitor System
Position
3300 5 & 8 mm Proximitor

System
3300 XL NSvTM Proximitor System
7200 5 & 8mm Proximitor System
7200 11mm Proximitor System
7200 14 mm Proximitor System
Display component for statuses

and variables
Display Hardware Identification
and manufacturing information
Context-specific help
System
Requirements
Users may install software on a
notebook or desktop computer that
meets these minimum requirements:
Microsoft Windows 2000 or
Windows XP operating system
800 MHz Pentium III class
processor
95% non-condensing, maximum
Note: The 1900/65A provides default configuration settings for

Bently Nevada transducers. The user can configure the 1900/65A
to accept other transducers.
256 MB RAM
8 MB video card
8x or faster CD-ROM drive
100 MB available hard drive space
FOR REFERENCE ONLY
Page 10 of 18
EN 61010-1
CE Mark Directives
The 1900/65A monitor has the CE
mark and is approved for installation
within the European Union and
European Environmental Agency
regions. The monitor has been
designed and tested to meet the
following directives.
Safety
Requirements
EMC Standards
This product is tested to meet Council
Directive 89/336/EEC Electromagnetic
Compatibility (EMC) and the listed
standards, in whole or in part,
documented in a technical construction
file. EN61000-6-4 Generic emission
standard, Part 2, Industrial
Environment. EN61000-6-2 EMC
Generic Immunity standard, Part 2,
Industrial Environment.
EMC Directives
EN61000-604
Radiated
Emissions
EN 55011, Class A
Conducted
Emissions
Hazardous Area Approvals
EN 55011, Class A
This monitor is not certified for

installation in Class 1 Div 1 locations,
but it will support transducers installed
in Div 1 locations via the use of
galvanic isolators and barriers. If
galvanic isolators are used, no change
is necessary to the installation. A
removable ground jumper allows the
monitor to support zener barrier
installations. Removing the jumper will
disconnect circuit common from
chassis at the monitor so that chassis
can be connected at the barrier.
EN61000-6-2
Electrostatic
Discharge
EN 61000-4-2, Criteria B
Radiated
Susceptibility
EN61000-4-3, Criteria A
Electrical Fast
Transient
Surge
Capability
Conducted
Susceptibility
Low Frequency
Conducted
Susceptibility
Safety Requirements for Measurement,

Control, and Laboratory Use
North American
Ex/AEx nA [L] IIC

Class I Division 2 Groups A B C D
T4 @ -20C Ta 70C
Vn = 18 to 36 Vdc @ Imax = 1A per
drawing 173089
EN61000-4-6, Criteria A
European
IEC 60945, Criteria A
@-20C Ta 70C
Low Voltage Directives

The 1900/65A Monitor meets Council
Directive 73/23/EEC Low Voltage
when the 24 Vdc power source is
approved to the Low Voltage
Directive. Bently Nevada power
supply P/N 02200794 meets this
requirement.
FOR REFERENCE ONLY

II 3G Ex nA [nL] IIC T4
Sira 06 ATEX 4053X

IECEx SIR 06.0012X per drawing
173089
Page 11 of 18
Ordering Information
1900/65A General Purpose Equipment Monitor
1900/65A-AXX-BXX-CXX-DXX-EXX
A: Power Option
B: Display Option
C: Mounting Option
00
18 to 36 Vdc
01
110 to 220 Vac @ 50 to 60

Hz (external supply)
00
No display
01
Attached display (no cable)
02
Display with 10 PVC cable
03
Display with 10
unassembled PVC cable
04
Display with 10 TEF cable
05
Display with 10
unassembled TEF cable
06
07
Display with 50
08
09
Display with 50
10
11
Display with 100

12
13
Display with 100

14
15
Display with 250

16
17
Display with 250

00
None
01
DIN rail mount (see Figure 1)
Figure 1: DIN Rail Mount

02
Bulkhead Mount (see Figure 2)
Figure 2: Bulkhead Mount

03
Fiberglass NEMA 4X/IP66 WP

housing with window in door
(see Figure 3)
Figure 3: NEMA 4X/IP66 WP Housing

04
1900/55 replacement kit (see

Figure 4)
Note: Uses existing 1900/55 weather-proof

housing and requires power option A01 (110/220
Vac to 24 Vdc external power supply)
FOR REFERENCE ONLY

Page 12 of 18
1900/01 1900/65A General Communications Monitor,

Communications Upgrade
1900/01-AXX-BXX-CXX-DXX
A: Order Type Option
01
01
98
Replacement licenses (key)
99
Update (CD)
B: Communications Option
01
Modbus communications
Figure 4: 1900/55 Replacment Kit

D: Approvals Option
00
New order (CD, key, and

binder)
C: License Key Type Option

00
None
None
01
USB license key
Multiple approvals. See

Hazardous Area Approvals
section for specific
certifications.
02
Floppy disk license key
D: License Quantity Option

XX
Total licenses (1 to 99)
E: Communications Option
00
None
01
FOR REFERENCE ONLY

Modbus communications
Page 13 of 18
Accessories
Use the part numbers listed in this section to order spare parts or additional components for your 1900/65A General Purpose
Monitor.
Part Number
Description
167699-02
1900/65A Display Module
173400-01
1900/65A Product Manual
172250-01
1900/65 Modbus Gateway Users Guide
173089-01
1900/65A Field Wiring Diagrams
02200794
Power supply, 110/220 Vac to 24 Vdc 2.5 A DIN rail mount
02200121
DIN rail end bracket
168374
35mm DIN rail mounting clip for 1900/65A Monitor Module
168495
Bulkhead mounting plate
168547-0010-01-01
3 m (10 ft) PVC cable, assembled
168547-0010-01-02
3 m (10 ft) PVC cable, unassembled
168547-0010-02-01
3 m (10 ft) TEF cable, assembled
168547-0010-02-02
3 m (10 ft) TEF cable, unassembled
168547-0050-01-01
168547-0050-01-02
168547-0050-02-01
168547-0050-02-02
168547-0100-01-01
168547-0100-01-02
168547-0100-02-01
168547-0100-02-02
168547-0250-01-01
168547-0250-01-02
168547-0250-02-01
168547-0250-02-02
168628
Stainless steel NEMA 4X weatherproof door for panel-mount display assembly
168629
Painted steel NEMA 4 weatherproof door for panel-mount display assembly
168944
Fiberglass NEMA 4X/IP66 weatherproof housing with window in door
02295055
MTL 728(-) barrier
02245002
MTL 796(-) barrier
172555
Modbus/TCP (Ethernet) to Modbus/RTU (Serial) Converter
169825-01
Training CD
FOR REFERENCE ONLY

Page 14 of 18
Dimensions
Note: All dimensions shown in millimeters (inches) except as noted.
Figure 5: Monitor Module Dimensions
Figure 6: Display Module Dimensions
FOR REFERENCE ONLY

Page 15 of 18
Figure 7: Combined Dimensions
FOR REFERENCE ONLY

Page 16 of 18
Figure 8: Weatherproof Housing Dimensions
FOR REFERENCE ONLY

Page 17 of 18
Figure 9: Weatherproof Door Drill Pattern
Figure 10: Weatherproof Door Dimensions

2006 Bently Nevada LLC
Proximitor, Velomitor, and NSvTM and System 1 are trademarks of the General Electric Company
Microsoft and Windows are registered trademarks of Microsoft Corporation
CSA is a registered trademark of CSA-International
Modbus is a registered trademark of Schneider Automation, Inc.
FOR REFERENCE ONLY
Page 18 of 18

Monitor GE 1900 - 65A

Uploaded by

Copyright:

Available Formats

Monitor GE 1900 - 65A

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Monitor GE 1900 - 65A

Uploaded by

Copyright:

Available Formats

Specifications and Ordering Information

1900/65A General Purpose Equipment Monitor

FOR REFERENCE ONLY

Specifications and Ordering Information

kind of variables or measurement

Continuous monitoring and protection is suitable for

Stand-alone operation on general-purpose equipment

Optional Modbus communications via

Velocity or Reciprocating Velocity

Small package. Monitor Module: 196.9 mm x 149.4

Radial Vibration (shaft vibration)

Thrust (shaft axial displacement)

DIN rail or bulkhead mounting options

18 to 36 Vdc power input. (optional 110-220 Vac

24-bit ADC conversion

Four vibration/position/speed inputs

Four temperature inputs

Configurable scale factors and full scale ranges

Up to four processed variables per channel with

Internal OK checking with status

Independent Alert and Danger setpoints

200-entry event list

Six relay outputs. Relay operation is programmable

Buffered outputs for each transducer channel

Four configurable 4-20 mA recorder outputs

Optional NEMA 4X/IP66 fiberglass housing with

Painted or stainless steel weatherproof door for panelmount display

Hazardous area approvals

Acceleration Variables and

Users can apply the acceleration

Transducer Channel Types

The Acceleration Channel Type and

Specifications and Ordering Information

Users may assign the value of the

Filter corner frequencies

0.5 Hz 25 kHz configurable 4-pole

125 Hz to 25 kHz, configurable

0.1 Hz min., but greater than

25 Hz to 5 kHz, configurable 4-pole

0.01 Hz 1-pole low-pass

1% of full scale range

The Velocity Channel Type and

Velocity Variables and Reciprocating

2.4 kHz 1-pole low-pass

Full Scale Range

Metric or English units

10 to 100 mm/s (0.4 to 4 in/s) peak and

20 to 500 m/s2 (2 to 50 g) peak and

FOR REFERENCE ONLY

Specifications and Ordering Information

Filter corner frequencies

0.09 Hz 1-pole low-pass

Full scale range

2.4 kHz 1-pole low-pass

10 to 50 mm/s (0.5 to 2 in/s) peak

Filter corner frequencies

Full Scale Range

Metric or English units