Installation Instructions

for Release 5.0

Offboard Diagnostic Information System Engineering

Installation Instructions for Release 5.0.6.

Contents

Introduction ................................................................................................................ 3

Configuring the computer/tester ................................................................................. 3

Installing the application............................................................................................. 4

3.1

Establishing the preconditions ........................................................................ 4

3.2

Uninstalling existing installations ..................................................................... 4

3.3

Running the installation routine ....................................................................... 4

3.4

Installing the D-PDU API ................................................................................. 5

Installing the runtime data .......................................................................................... 6

Starting the application .............................................................................................. 7

Configuration ............................................................................................................. 7
6.1
Bluetooth configuration with the "Softing EDIC Configuration Manager"
application ...................................................................................................................... 7
6.2

Configuring the mail client ............................................................................. 10

6.3

Help .............................................................................................................. 10

ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32

Page 2 of 10

Offboard Diagnostic Information System Engineering

Installation Instructions for Release 5.0.6.

1 Introduction
This document describes the steps required to successfully install the design engineer diagnostic
tester, OFFBOARD DIAGNOSTIC INFORMATION SYSTEM Engineering, in the following referred
to as Engineering Diagnostic Tester. The installation process consists of the following four main
steps:
1.
2.
3.
4.

Configuring the computer/tester,

Installing the application,
Installing the runtime data and
Configuring the application.

The individual steps are described in the following sections.

2 Configuring the computer/tester

The vehicle's diagnostic connection for the Engineering Tester is not reliably standby-capable.
! It is therefore recommended to adjust the computer's power options in such a way that
neither standby mode nor idle mode are enabled.
Switching manually to the computer's operating modes mentioned should also be avoided when
using the Engineering Tester.
The settings for the power options are available at Start System control All system control
elements Power options.
Figure 1 shows the settings required for standby. It is also advisable to change the settings in the
power options to "Do nothing" when closing the tester.

Figure 1: Settings for the power options

ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32

Page 3 of 10

Offboard Diagnostic Information System Engineering

Installation Instructions for Release 5.0.6.

3 Installing the application

Please note Chapter 3.4.

3.1 Establishing the preconditions

1. To install the application, you require administrator rights on your PC.
2. If you do not have a valid licence, please start the procurement transaction via the product
website www.dne-elektronik.de.
Installation is possible with an initiated licence. However, to start and use the application, you
require a valid licence.
3. Download the OFFBOARD DIAGNOSTIC INFORMATION SYSTEM Engineering installation
package from the product website www.dne-elektronik.de:
PRD-ODISEngin_windows_5.0.6_TEMR140.exe
Internal Volkswagen link via DoRIS:
https://dorisappl.wob.vw.vwg/doris/publicdocuments/30083594?htmlKey=krGVk0eDB3&useInli
neContent=false

3.2 Uninstalling existing installations

If there is an older version of Engineering Diagnostic Tester on your PC, this old version will need
to be completely uninstalled first. To do this, use the corresponding link in the start menu and restart the computer.

3.3 Running the installation routine

Start setup by right-clicking on the downloaded installation package: "Run as administrator", (!)
even if you are already logged on as the administrator, and follow the instructions of the installation wizard. You can specify any path as desired when selecting the target directory for installing
the application and the diagnostic components. You do not have to use the proposed default path.
However, it is practical for the event that you require any support.
In the dialogue for selecting the certificate, enter the path for the licence file (e.g. "license.dat").
Note:
Do not remove the check mark from "Copy to installation directory". The application will then copy
the licence file to the installation directory and manage it there.
During the installation process, you will be requested to select the target platform (computer hardware) for the installation. For this, the items "* with VAS 5054 radio head" and "* with VAS 6154"
are provided (cf. Figure 2).
Please select radio head VAS 5054 for normal CAN diagnosis.

ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32

Page 4 of 10

Offboard Diagnostic Information System Engineering

Installation Instructions for Release 5.0.6.

Figure 2: Selecting the target platform

3.4 Installing the D-PDU API

There is a setup wizard for installing the Softing D-PDU API, which is activated automatically by the
setup routine of the Offboard Diagnostic Information Engineering Diagnostic Tester.
In some cases it could happen that the setup routine may demand for your intervention.
If that is the case you have to note following instructions:
-

Please click Next respectively Weiter according to Figure 3

Please click again Next respectively Weiter in the following dialogue without taking
changes (Figure 4).

ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32

Page 5 of 10

Offboard Diagnostic Information System Engineering

Installation Instructions for Release 5.0.6.

Figure 3: Setup of the D-PDU API

Figure 4: Assortment of required components

4 Installing the runtime data

As the final step, the installation of current vehicle projects in runtime format is required for the
Engineering Diagnostic Tester.
They are provided separately by the individual Volkswagen brands.

ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32

Page 6 of 10

Offboard Diagnostic Information System Engineering

Installation Instructions for Release 5.0.6.

5 Starting the application

After installing the application as described and restarting the tester, OFFBOARD DIAGNOSTIC
INFORMATION SYSTEM Engineering can be started using the corresponding item in the Windows
start menu.
To configure Volkswagen Diagnostic VCIs VAS505x under Windows 7, please observe the instructions in chapter 6.1.
Configuring the mail client for support purposes has also changed with Release 4.1.x. Please observe the corresponding notes in chapter 6.2.

6 Configuration
6.1 Bluetooth configuration with the "Softing EDIC Configuration
Manager" application
Note:
Manual Bluetooth pairing should not be established beforehand!

1. Start "Softing EDIC Configuration Manager" at Start All programs Softing D-PDU
API No Action button is enabled in the application window.

2. Connect via USB and press the "Refresh" button. (Figure 5)

Figure 5: Active USB connection

ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32

Page 7 of 10

Offboard Diagnostic Information System Engineering

Installation Instructions for Release 5.0.6.

3. Disconnect USB again and press the "Refresh" button again.

Then press the "Add New Device" button. ( Figure 6)

Figure 6: Disconnected USB link

4. Observe the message and click on "OK". (Figure 7)

Figure 7: Connect Bluetooth message

ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32

Page 8 of 10

Offboard Diagnostic Information System Engineering

Installation Instructions for Release 5.0.6.

5. The Bluetooth device is detected by a scan. Select Bluetooth Device and click on "Next".
That configures the device and assigns a port to it. (Figure 8)
(If pairing was successful, please continue with step 7, if not continue with step 6.)

Figure 8: Device search and automatic pairing

6. If the device is not automatically detected, manual pairing is required first in the installed
Bluetooth stack. The configured port can then be entered or selected manually using the
"Enter COM Port" button. Then press "Next". (Figure 9)

Figure 9: Manual port assignment

ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32

Page 9 of 10

Offboard Diagnostic Information System Engineering

Installation Instructions for Release 5.0.6.

7. The device with the configured port is detected. The "Configuration details" button can be
used for checking. The "Softing EDIC Configuration Manager" can be closed.

6.2 Configuring the mail client

To be able to send support mails from the Engineering Tester, you need to enter the support address. For this, open the Admin settings of the Engineering Tester and enter the e-mail address
[email protected] on the Support tab.
A firewall for sending e-mails from the Engineering Diagnostic Tester may need to be configured by
your IT service specialist. It is normally sufficient to grant the "OffboardDiagLauncher.exe" application access to the port.
Attention!
The support function has been adjusted to using the standard mail client installed on the
computer. If this is Microsoft Outlook, the problem will occur that Outlook interprets the
mail address as a contact. However, since e.g. the contact [email protected]
does not exist, sending the e-mail will not work.
This problem can currently only be avoided by re-entering the recipient address manually in
the Outlook mail window.

6.3 Help
If you have any more questions during installation or configuration, please contact the configured
support specialist after reading these instructions.

ODIS Engineering Team, Tel. +49 (5361) 9 - 16 1 32

Page 10 of 10