Audio Delay Box

AD-100

Instruction Manual
Rev 171209

www.datavideo-tek.com

Table of Contents
Warnings and Precautions .......................................................................................... 2
Warranty ...................................................................................................................... 3
Disposal ...................................................................................................................... 3
Packing List ................................................................................................................. 3
Introduction ................................................................................................................. 4
Features ...................................................................................................................... 4
Connections & Controls............................................................................................... 5
Front Panel .................................................................................................................. 5
Rear Panel .................................................................................................................. 6
AD-100 MENU Settings ............................................................................................... 7
1. AUDIO_DELAY .................................................................................................... 7
2. DELAY_TIME ....................................................................................................... 7
3. ATTENUATION .................................................................................................... 7
4. TONE_OUT .......................................................................................................... 8
5. TONE_MODE....................................................................................................... 8
6. TONE_LEVEL ...................................................................................................... 8
7. RESET ALL .......................................................................................................... 9
8. SOFTWARE VERSION ........................................................................................ 9
9. ESCAPE ............................................................................................................... 9
Example Set Up ........................................................................................................ 10
Specification .............................................................................................................. 10
Service & Support ..................................................................................................... 11

Warnings and Precautions

1. Read all of these warnings and save them for later reference.
2. Follow all warnings and instructions marked on this unit.
3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
4. Do not use this unit in or near water.
5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage.
6. Slots and openings on the cabinet top, back, and bottom are provided for ventilation. To ensure safe and
reliable operation of this unit, and to protect it from overheating, do not block or cover these openings. Do
not place this unit on a bed, sofa, rug, or similar surface, as the ventilation openings on the bottom of the
cabinet will be blocked. This unit should never be placed near or over a heat register or radiator. This unit
should not be placed in a built-in installation unless proper ventilation is provided.
7. This product should only be operated from the type of power source indicated on the marking label of the
AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local
power company.
8. Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will be
walked on, rolled over, or otherwise stressed.
9. If an extension cord must be used with this unit, make sure that the total of the ampere ratings on the
products plugged into the extension cord do not exceed the extension cords rating.
10. Make sure that the total amperes of all the units that are plugged into a single wall outlet do not exceed
15 amperes.
11. Never push objects of any kind into this unit through the cabinet ventilation slots, as they may touch
dangerous voltage points or short out parts that could result in risk of fire or electric shock. Never spill
liquid of any kind onto or into this unit.
12. Except as specifically explained elsewhere in this manual, do not attempt to service this product yourself.
Opening or removing covers that are marked Do Not Remove may expose you to dangerous voltage
points or other risks, and will void your warranty. Refer all service issues to qualified service personnel.
13. Unplug this product from the wall outlet and refer to qualified service personnel under the following
conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under normal operating conditions. Adjust only
those controls that are covered by the operating instructions in this manual; improper adjustment
of other controls may result in damage to the unit and may often require extensive work by a
qualified technician to restore the unit to normal operation;
e. When the product has been dropped or the cabinet has been damaged;
f. When the product exhibits a distinct change in performance, indicating a need for service.
NB: The factory default audio levels on this unit may be louder than expected. Please review and adjust the
menu settings BEFORE connecting any output connections on the AD-100 rear panel.
The AD-100 is an Audio Delay device and it can also be used as a Tone Generator. Please DO NOT connect the
AD-100 directly to a headset or a set of speakers - it should not be used like an Audio AMP.

Warranty
Standard Warranty
Datavideo equipment is guaranteed against any manufacturing defects for one year from the date of
purchase.
The original purchase invoice or other documentary evidence should be supplied at the time of any
request for repair under warranty
Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not covered by this
warranty.
All mail or transportation costs including insurance are at the expense of the owner.
All other claims of any nature are not covered.
Cables & batteries are not covered under warranty.
Warranty only valid in the country or region of purchase
Your statutory rights are not affected.

Two Year Warranty

AllDatavideoproductspurchasedafter01Oct.2008qualifyforafreeoneyearextensiontothe
standardwarranty,providingtheproductisregisteredwithDatavideowithin30daysofpurchase.
Forinformationonhowtoregisterpleasevisitwww.datavideotek.comorcontactyourlocalDatavideo
officeorauthorizedDistributors

CertainpartswithlimitedlifetimeexpectancysuchasLCDPanels,DVDDrives,HardDrivesareonly
coveredforthefirst10000hours,or1year(whichevercomesfirst)

AnysecondyearwarrantyclaimsmustbemadetoyourlocalDatavideoofficeoroneofitsauthorized
Distributorsbeforetheextendedwarrantyexpires.

Disposal
For EU Customers only - WEEE Marking
This symbol on the product indicates that it should not be treated as household waste. It must
be handed over to the applicable take-back scheme for the recycling of waste electrical and
electronic equipment. For more detailed information about the recycling of this product, please
contact your local Datavideo office.

Packing List
Items

Description

Qty

AD-100

AC Power Cord

Switching Adaptor DC 12V / 1A

AD-100 Instruction Manual

Introduction
The Datavideo AD-100 is an easy to use Audio Delay box that enables you to synchronize
video and audio. The AD-100 can also be used as a 1KHz Tone Generator. The unit features
traditional RCA (phone) connectors as well as Professional Balanced XLR type connections.
Built into a rugged metal housing, it is ideal for use either in the field or in a studio setup.

Features
Audio Input:

Balanced Audio (XLR) x 2

Unbalanced Audio (RCA) x 2
Audio delay Output:

Balanced Audio (XLR) x 2

Unbalanced Audio (RCA) x 2
LCD display for Menu and Mode selection setting
Output volume attenuating from 0 ~ - 60 dBu
Audio delay time from 0 ~ 700m SEC
1KHZ test tone output attenuating from +26 ~ - 34 dB
DC 12V input

Connections & Controls

Front Panel

Power Switch
Switches the power On / Off.

MENU
This switch allows access to the 9 mode system settings.

MODE
Select LEVEL or TIME information on LCD Display.
LEVEL will display the audio output dBu level.
TIME will display the AUDIO DELAY & ATTENUATION settings.

ADJUST
The ADJUST knob is for mode select and value adjustment.
It can be rotated to display the correct menu option or value and then
pressed in to select or confirm a chosen value.

Rear Panel

AUDIO OUT
2 channels XLR balanced audio output.
2 channels RCA unbalanced audio output.
For reference : 4dBu (XLR) = -10dBV (RCA)

AUDIO IN
2 channels XLR balanced audio input.
2 channels RCA unbalanced audio input.

DC In Socket
Connect the supplied 12V 1.5A PSU to this socket. The connection
can be secured by screwing the outer fastening ring of the DC In plug
to the socket.

Grounding Terminal
When connecting this unit to any other component, make sure that it
is properly grounded by connecting this terminal to an appropriate
point. When connecting, use the socket and be sure to use wire with
a cross-sectional area of at least 1.0 mm2.

AD-100 MENU Settings

N.B. The unit will automatically exit the MENU settings mode if it is left idle for 12 seconds or more.

1. AUDIO_DELAY
This setting switches the audio delay function on or off.

- Press the MENU button to enter the system configuration settings.

- The cursor will flash at the beginning of this menu option.
- Press MENU button again to move the flashing cursor to the setting position.
- Turn the ADJUST knob to select the setting audio delay ON or OFF.
- Press the ADJUST knob in to save or confirm the chosen setting.
- The flashing cursor will return to the beginning of this menu option.
- Rotate the ADJUST knob to choose another menu option or press the mode button.

2. DELAY_TIME
This setting adjusts the audio delay in 10 millisecond (ms) increments to a maximum delay of 700ms.
NB:

1000ms = 1 second

: 1 frame PAL = 40ms :

1 frame NTSC = 33.333ms

- Press the MENU button to enter the system configuration settings.

- Turn the ADJUST Knob to select DELAY_TIME mode.
- The cursor will flash at the beginning of this menu option.
- Press MENU button again to move the flashing cursor to the setting position.
- Turn the ADJUST knob to select the DELAY_TIME setting value from 0 ~ 700m SEC.
- Press the ADJUST knob in to save or confirm the chosen setting.
- The flashing cursor will return to the beginning of this menu option.
- Rotate the ADJUST knob to choose another menu option or press the mode button.

3. ATTENUATION
This setting adjusts how loud or quiet the audio will be at the output. 0dB=Loud and -60dB=Quiet.
NB: The AD-100 is an Audio Delay device and it can also be used as a Tone Generator. Please DO NOT
connect the AD-100 directly to a headset or set of speakers it should not be used like an Audio AMP.

- Press the MENU button to enter the system configuration settings.

- Turn the ADJUST Knob to select ATTENUATION setting.
- The cursor will flash at the beginning of this menu option.
- Press MENU button again to move the flashing cursor to the setting position.
- Turn the ADJUST knob to select the ATTENUATION setting value from 0 ~ - 60 dB.
- Press the ADJUST knob in to save or confirm the chosen setting.
- The flashing cursor will return to the beginning of this menu option.
- Rotate the ADJUST knob to choose another menu option or press the mode button.

N.B. The unit will automatically exit the MENU settings mode if it is left idle for 12 seconds or more.

4. TONE_OUT
This setting switches the TONE_OUT function on or off.

- Press the MENU button to enter the system configuration settings.

- Turn the ADJUST Knob to select TONE_OUT setting.
- The cursor will flash at the beginning of this menu option.
- Press MENU button again to move the flashing cursor to the setting position.
- Turn the ADJUST knob to change the TONE_OUT setting between ON or OFF.
- Press the ADJUST knob in to save or confirm the chosen setting.
- The flashing cursor will return to the beginning of this menu option.
- Rotate the ADJUST knob to choose another menu option or press the mode button.
N.B. The test tone will be output at the level set within the TONE_LEVEL menu option. This test tone will
also override any audio source already being fed through the AD-100.

5. TONE_MODE
This setting allows the 1KHz test tone to be switched on or muted.

- Press the MENU button to enter the system configuration settings.

- Turn the ADJUST Knob to select TONE_MODE setting.
- The cursor will flash at the beginning of this menu option.
- Press MENU button again to move the flashing cursor to the setting position.
- Turn the ADJUST knob to change the TONE_MODE setting between MUTE or 1KHZ.
- Press the ADJUST knob in to save or confirm the chosen setting.
- The flashing cursor will return to the beginning of this menu option.
- Rotate the ADJUST knob to choose another menu option or press the mode button.
N.B. The MUTE value will silence the test tone but will not restore any audio source being fed into the AD100. Please set the TONE_OUT menu option to OFF to switch back to an audio input source instead.

6. TONE_LEVEL
This setting adjusts how loud or quiet the test tone will be at the output. +26dBu=VERY Loud and -34dBu=Quiet.

- Press the MENU button to enter the system configuration settings.

- Turn the ADJUST Knob to select TONE_LEVEL setting.
- The cursor will flash at the beginning of this menu option.
- Press MENU button again to move the flashing cursor to the setting position.
- Turn the ADJUST knob to select the TONE_LEVEL setting value from +26 ~ - 34 dBu.
- Press the ADJUST knob in to save or confirm the chosen setting.
- The flashing cursor will return to the beginning of this menu option.
- Rotate the ADJUST knob to choose another menu option or press the mode button.

N.B. The unit will automatically exit the MENU settings mode if it is left idle for 12 seconds or more.

7. RESET ALL
Please remove all output connections before using this feature.
This option restores the factory defaults which may be louder than expected. Please review and adjust the
default menu settings before re-connecting any output connections on the AD-100 rear panel.
NB: The AD-100 is an Audio Delay device and it can also be used as a Tone Generator. Please DO NOT
connect the AD-100 directly to a headset or set of speakers it should not be used like an Audio AMP.

- Press the MENU button to enter the system configuration settings.

- Turn the ADJUST Knob to select the RESET ALL setting.
- The cursor will flash at the beginning of this menu option.
- Press MENU button again to move the flashing cursor to the setting position.
- Turn the ADJUST knob to change the RESET ALL setting from NO to YES.
- Press the ADJUST knob in for 2 seconds, the system will return to the factory defaults.
- The setting will return to NO.
- Press the MENU or MODE button to start to review the units default settings.

Factory Default Settings

AUDIO_DELAY
OFF
DELAY_TIME
10ms
ATTENUATION
-0dB
TONE_OUT
OFF
TONE_MODE
1KHz
TONE_LEVEL
+4dBu

8. SOFTWARE VERSION
- Press the MENU button to enter the system configuration settings.
- Turn the ADJUST knob to select SOFTWARE VERSION.
- The firmware version of the AD-100 is displayed for 12 seconds.

9. ESCAPE
- After reviewing or changing the system configuration settings.
- Turn the ADJUST knob to select ESCAPE.
- Press the ADJUST knob in to exit the system configuration settings mode.
- Alternatively press the MODE button to exit the system configuration settings instantly.

Example Set Up

Specification
Audio inputs

2 x balanced stereo audio, XLR connectors

2 x unbalanced stereo audio, RCA / Phone sockets

Audio Output

2 x balanced stereo audio, XLR connectors

2 x unbalanced stereo audio, RCA / Phone sockets

Audio Spec
Operating
Temperature
Humidity
Dimension &
Weight
Power

Bandwidth 20~20KHz < +/- 3dB

S/N Ratio > 70 dB
THD. < 0.1% (This spec must use precision to analyze data inside of signal)
0C to 40C (32F to 102F)
10% to 90% (non condensing)
205mm (W) x 235mm (D) x 45mm (H) / 2.8 lbs/ 1.3 Kgs
DC 12V / 1A

10

Service & Support

It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist
you in setting up and operating your system. Please refer to our web site www.datavideo-tek.com for answers to
common questions, support requests or contact your local office below.
Datavideo Global Website: www.datavideo-tek.com
Datavideo Corporation
Tel: +1 562 696 2324

Fax: +1 562-698-6930

E-Mail: [email protected]

Datavideo Technologies Europe BV

Tel: +31-30-261-96-56
Fax: +31-30 261-96-57

E-Mail: [email protected]

Datavideo UK Limited
Tel: +44 1457 851 000

E-Mail: [email protected]

Fax: +44 1457 850 964

Datavideo Technologies Co., Ltd

Tel: +886 2 8227 2888
Fax: +886-2-8227-2777

E-mail: [email protected]

Datavideo Technologies China Co., Ltd

Tel: +86 21-5603 6599
Fax:+86 21-5603 6770

E-mail: [email protected]

Datavideo Technologies (S) PTE Ltd

Tel: +65-6749 6866
Fax: +65-6749 3266

E-mail: [email protected]

Datavideo HK Ltd
Tel: +852 2833 1981

E-mail: [email protected]

Fax: +852-2833-9916

All the trademarks are the properties of their respective owners.

Datavideo Technologies Co., Ltd. All rights reserved 2018

P/N: G082060448E1
11