(381611313) BOQ Earthwork

Construction of Residential & Amenities, Services and Road
for National Thermal Power Corporation
Name of work :-
PART - I CIVIL WORKS

ABSTRACT OF COST
PART
DESCRIPTION
PAGE
Sub-Structure
Super structure (Structural)
Form work
Reinforcement work
10
Masonry work
11
Flooring work
17
Doors and windows
24
Fittings & Fixtures
27
Water proofing work
29
Plastering work
30
Painting work
32
Miscellaneous work
39
Total of Part - I :
AMOUNT (Rs.)
SCHEDULE OF QUANTITIES
SN
QNTY.
DESCRIPTION OF ITEM
RATE
UNIT
PART I-A - SUB STRUCTURE

1
Cement concrete of specified grades at all

locations & depths for the following works using
graded stone aggregate of 20mm maximum size
including necessary form work, machine mixing,
transporting, placing in position consolidation,
finishing, curing etc. complete all as per
specifications, drawings & as directed by the
Eingineer in charge.
Note :-
Nominal reinforcement if provided

shall be measured & paid under relevant item.
1602.00
Cum
(i) P C C in Grade M10 in bed concrete to

foundations, pedestal etc.
Cum
2470.00
Cum
(ii) P C C in Grade M15 in sub base flooring,

foundation , pedestals, cable pits, cable trenches,
plinth protection etc.
Cum
4071.00
Cum
(iii) Extra over item No. 5 (i) and 5 (ii) above for
providing RMC (Ready Mixed Concrete)
confirming to IS 4926 (latest) in lieu of
conventional PCC items supplied by approved
RMC manufactures for all type of structural / PCC
elements
Cum
NOTES FOR REINFORCED CEMENT CONCRETE
a)
Cement for structural works shall be OPC/ PPC ISI marked and
duly approved by the Engineer-in-charge
b)
PPC/ blended cement of ISI marked shall only be used for

finishing works on prior approval of Engineer-in-charge
c)
All RCC work shall be controlled concrete unless otherwise

specified and shall be carried out strictly in accordance with the
drawings and specifications.
d)
The rates for RCC works shall be exclusive of cost of

reinforcement and form work unless otherwise mentioned.
e)
All coarse aggregate to be of 20mm. maximum size &

uniformly graded unless otherwise mentioned.
f)
For all RCC items, the rates quoted shall include the following
without any extra cost to the Department.
i)
ii)
Spacers to maintain clear cover for reinforcement.

Fixing at correct level and in proper alignment the inserts, pipe
sleeves, pipe bends, hooks, other pipe specials etc. supplied by/
through the Department.
Test for Concrete shall be done as per IS 456-2000. and the
t f th
h ll b b
b th
t t
iii)
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
RATE
UNIT
Reinforced Cement Concrete of fillowing grades in

in foundation and plinth at all levels and locations
conforming to I.S. 456-2000 using 20mm.
maximum size down graded stone aggregate
including machine mixing, conveying, placing in
position, mechanical consolidation, finishing,
curing etc.all complete as per specifications ,
drawings and as directed by the Engineer in
Charge .
a) For all type of structural / RCC elements
with all geometrical shapes.
25094.00 i) RCC of Grade M30
Cum
Extra over item No. 6 (i) above for providing
RMC
(Ready Mixed Concrete) confirming to IS
9365.00
4926 (latest) in lieu of conventional RCC items
Cum
supplied by approved RMC manufactures for all
type of structural / RCC elements
Providing, erecting, fixing in position striking /
20141.00 removing and cleaning steel / timber shuttering &
centering for form work in foundation plinth at all
Sqm
locations for all geometrical shapes in plain,
curved surfaces of structural / RCC elements
including chamfers, splays, keys, wedges, props,
rails, bracings, brackets, cutting holes for pipes
etc., providing & applying approved form oil on all
surfaces of form work coming in contact with
concrete including close hacking of all exposed
concrete work after removal of form work, all
materials, labour etc. all complete as per
specifications, drawings and as directed by the
Engineer-in-charge.
Note:-
Cum
Cum
Sqm
i) Area of form work in contact with concrete shall only be

measured for payment and stop boards for construction
joints will not be measured for payment.
ii)The rate of formwork shall include all type of structural /
RCC elements and geometric shapes including circular and
any other curved surfaces.

Reinforcement for RCC work including supplying,
delivering, storing of various diameters as
required at site of work including loading,
unloading, transporting, decoiling, straightening,
cutting, bending, placing in position at all locations
& levels and binding with 18 gauge, soft drawn
annealed steel binding wire including carrying out
various tests as required etc. all as per
Engineer in Charge
1632.00
i) Thermo Mechanically Treated bars of grade
MT
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
RATE
UNIT
and RINL.
Note:- The cost of binding wire shall be borne by the contractor
and binding wire shall not be measured for payment.
2217.00
Cum
Brick masonry work in foundation and plinth,cable

pits, trench, steps etc. using well burnt bricks from
approved lot, of class designation 75
(classification as per IS 1077-1992 and min.
average compression strength not less than 7.50
N/mm2 ) in C.M 1: 6 to correct line, level and
plumb including raking out joints/simultaneous flush
pointing with cement mortar 1:4, curing etc. all
complete as per specifications, drawings and as
directed by Engineer in Charge.
Cum
Note:- i)One brick wall thickness shall be considered as 250 mm &

lesser wall thickness if any shall be made up accordingly
by the contractor by applying cement mortar of mix 1:4 in
proper line, level & plumb without any extra cost to the
Department.
ii) The rate shall include cost of making the brick masonry
to all geometrical shapes and sizes without any extra cost
to the Department.
7
584.00
Cum
Cum
Cement pointing to random rubble masonry wall

with cement mortar 1:3 including raking out joints,
pointing neatly and finishing the joints, curing
scaffolding etc. complete all as per specification,
drawing and as directed by the Engineer in charge.
2917.00
Sqm
9
Providing random rubble masonry with rough

dressed hard stone below plinth in foundation,
plinth, retaining wall ,compound wall etc. in cement
mortar 1:6 including through stone, header stone,
bond stone, quoins etc. well packed including
filling the interstices with smaller stone chips,
striking, raking out joints & finishing the joints,
including scaffolding, curing etc. all complete as
per specifications, drawings and as directed by
the Engineer in Charge.
517.00
Cum
a) Raised and cut pointing

Providing laterite stone masonry with rough
dressed hard stone below plinth in foundation,
plinth, retaining wall ,compound wall etc. in cement
mortar 1:6 including through stone, header stone,
bond stone, quoins etc.laid to line, level plumb etc.
including striking, raking out joints & finishing the
joints, including scaffolding, curing etc. all
directed by the Engineer in Charge.
Sqm
Cum
AMOUNT
RATE
UNIT
SN
QNTY.
Sqm
DESCRIPTION OF ITEM
all locations to correct line, level, plane and plumb
for cable pits trenches, chambers,steps etc.,
finished smooth with neat cement finish, including
preparing the surface, scaffolding, curing etc. all
complete as per drawings, specifications and as
11
8182.00
Cum
Filling in plinth with selected earth excavated

from nearby borrow areas with in 2.0 km by
mechanical transport including all leads,
lifts,loading, unloading, stacking, levelling,
spreading, in layers not exceeding 150 mm thick,
breaking clods, watering, consolidation to obtain
90% proctor density etc.all complete as per
Engineer in Charge.
Cum
12
8148.00
Cum
Disposing off the surplus excavated materials by

mechanical transport to the neareby dumping pits/
dumping areas inside the campus within a lead of
2.0 km including all leads, lifts, loading, unloading,
stacking, spreading, levelling etc.all complete as
per specifications & as directed by the Engineer in
Charge
Cum
Note:- Voids @ 20% for soils and 50% for soft rock/hard rock
shall be deducted from fully loaded truck measurements
to arrive at the net quantity for payment in case direct
measurement is not possible.
13
Providing and laying dry rubble stone hard core

soling of following consolidated thickness in sub
base to floor and in plinth protection to required
levels and lines with first quality rubble, hand set,
well packed including filling the interstices with
smaller stone chips, supplying & finishing / blinding
the surfaces with approved blinding quality murrum
including watering, consolidation etc. all complete
as per specification drawings & as directed by
Engineer in Charge.
16207.00 i) 150mm consolidated thickness
Sqm
14
Sqm
Supplying and spreading pesticides

19618.00
CHLORPYRIPHOS or other chemical approved by
Sqm
central insecticides board as directed by the
manufacturer and spraying the mixture uniformly by
sprayer as pre-construction antitermite treatment
at the rate of 7.5 liters per sq.m. on vertical and 5
ltrs. per sq.m. on horizontal surfaces (or as
directed by the manufacturer ) within the trenches,
50% of the emulsion to be filled in the holes made
in trenches at 150mm. centre to centre etc.
l t
IS 6313 P t II &
di
t db
Sqm
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
the Engineer-in-charge. (The payment will be
made on the basis of plinth area measurement
only at ground floor/stilt area for all stages of
operation and vertical face will not be measured
for payment) complete as per specifications,
drawings and as directed by the
Engineer-in-charge.
RATE
UNIT
Notes :a) This item will be executed through approved agency who is a
member of Indian Pest Control Association, approved by Central

Insecticides Board.
b) The contractor shall have to furnish ten years guarantee in the
prescribed proforma as per Section-10 (iv) Conditions and
clauses of contract, to maintain the anti-termite treated
area/structure free from termite.
c) Prior approval of Engineer in Charge shall be obtained after
testing the chemical for antitermite to be used and shall be tested
in approved laboratory and to be submitted to Engineer in
Charge. Cost of testing shall be included in the rates quoted.
15
1930.00
Sqm
Providing and laying damp proof course 38mm

thick at plinth level in cement concrete 1:2:4 using
10mm. maximum size and down graded stone
aggregate, mixed with approved water proofing
compound at 2% by weight of cement laid to
levels, slopes etc. including applying a coat of hot
bitumen of grade 80/100 at 17 kg./10 sq.m.
including cost of form work, curing all complete as
per specifications & as directed by the Engineer in
Charge.
Sqm
16
1742.00
Sqm
Providing and laying patent box type cement

based water proofing treatment of approved
agency for basement raft and lift wall at all levels &
locations as per specification of the water proofing
agency including cleaning of surfaces, curing and
testing the lift pit for water tightness, rectification of
defects if any, etc. complete as per specification
and drawing and as directed by the
Engineer-in-charge as per the following.
Sqm
a) Providing 50 mm to 70mm thick water proofing

treatment for base / floor consisting of
i) Ist layer shahabad stone of approx. size
600x600x20mm thick of approved quality,(rough
stone slab) over a 25mm thick base of cement
mortar 1:3 (1 cement:3 course sand) mixed with
waterproofing compound conforming to IS:2645 in
the recommended proportion, joints sealed and
grouted with cement slurry mixed with water
proofing compound conforming to IS: 2645 in
proportions recommended by the manufacturer.
ii) 2nd layer of 25mm thick cement mortar 1:3
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
(1cement : 3 coarse sand ) mixed with water
proofing compound in recommended proportions.
RATE
UNIT
iii) Finishing top with stone aggregate of 10mm to

12mm nominal size spreading @ 8 cudm/sqm
thoroughly embedded in the 2nd layer
b) Providing and laying integral cement based
treatment for water proofing on the vertical surface
by fixing shahabad stone of approx. size
600x600x20mm thick of approved quality,(rough
stone slab) with cement slurry mixed with water
proofing compound conforming to IS: 2645 in
recommended proportion with a gap of 20mm
(minimum) between stone slabs and the receiving
surfaces and filling the gaps with neat cement
slurry mixed with water proofing compound and
finishing the exterior stone slab with cement
mortar1:4(1 cement: 4 coarse sand) 20mm thick
with neat cement punning mixed with water
proofing compound in recommended proportion
complete at all levels and as directed by
Engineer-in-charge.
Notes:a) The contractor shall get written approval from the Engineer
-in-Charge, for the water proofing agency engaged and shall
submit the specification of the waterproofing before
commencement of work.
b) The contractor shall test the surface where water proofing
treatment provided for bone dry condition by filling up with water.
No wet patches or leaks shall appear on the surrounding wall or
under side of the slab.
c) The contractor shall furnish guarantee bond on appropriate
stamp paper in the proforma as per Section-10 (iii) conditions
and clauses of contract for the entire waterproofing treatment for
maintaining the surroundings and under side surfaces of the
waterproofing treatment in bone dry condition for 10 years. During
the guarantee period the contractor shall attend all leakages,
defects etc. if noticed, free of cost, starting the work of checking up
and rectification within a week's time from the date of intimation
about such leakages/defects
d) The Contractor shall keep the lift well filled with water after the
water proofing work has been completed and shall clean it before
handing over. At no time shall the lift pit be kept empty. Testing
for the bone dry condition for the water proofing work carried out
shall again be done, before handing over, if found necessary by
the Engineer- in-Charge.
TOTAL OF PART 1 - A : (Sub Structure)
Rs.
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
RATE
UNIT
PART I-B : SUPER-STRUCTURE (STRUCTURAL)

Notes : i) Super structure items included in this schedule pertains to
all the works above plinth level upto roof including parapets,
water tanks,machine room, terrace level works etc. unless
specified otherwise.
REINFORCED CEMENT CONCRETE.
a) All RCC works shall be controlled concrete unless otherwise
specified and shall be carried out strictly in accordance with the
drawings, specifications and as directed by the Engineer in Charge.
b) The rates for RCC works shall be exclusive of cost of
reinforcement and form work unless otherwise mentioned.
c) All coarse aggregate to be 20mm. maximum size and uniformly
graded unless otherwise mentioned.
d) For all RCC items, the rates quoted shall include the following
without any extra cost to the Dept.
i. Spacers to maintain clear cover for reinforcement.
ii. Fixing at correct level and in proper alignment the inserts, pipe
sleeves, pipe bends, fan hooks, other pipe specials etc.supplied
by/ through the Department.
iii. Cut out in slabs, construction joints etc.
iv. Test for concrete shall be done as per IS 456-2000 and the cost
of the same shall be borne by the contractor.
17
18
Reinforced cement concrete of grade as

mentioned below in super structure conforming to
IS 456-2000, at all floors and levels for all structural
members in all geometrical shapes/ design using
graded stone aggregate of 20mm and down
graded including machine mixing, conveying,
placing in position, mechanical consolidation,
finishing, curing, etc. complete all as per drawings,
specifications & as directed by Engineer in
Charge.
a)For all type of Structural/ RCC Elements
17895.00 i) RCC of Grade M30
Cum
17895.00 Extra over item 21 (i) ) above for providing RMC

(Ready Mixed Concrete) conforming to IS 4926
Cum
(Latest) in lieu of conventional RCC items,
supplied by approved RMC manufacturers.
Cum
TOTAL OF PART I-B : [ Super Structure ~ Structural ]
Rs.
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
RATE
UNIT
PART - I-C : FORM WORK

Notes:i) The rate of formwork shall include all type of structural /
RCC elements and geometric shapes including circular
and any other curved surfaces at all height and locations
with independent staging having adequate additional
bracing , proping, intermediate/multiple staging required if
any etc.
ii) For double/ multi stage shuttering design calculations and
details / drawings for scaffolding shall be submitted by
the contractor well in advance. Prior written approval
of form work shall be obtained from Engineer in Charge,
before commencement of work.
19
20
Providing, erecting, fixing in position, striking /

removing and cleaning steel / timber shuttering &
centering for form work at all level & locations
including intermediate / multiple staging for all
geometrical shapes and designs including rails,
bracings, props, brackets, cutting holes for pipes
etc., providing & applying approved form oil on all
concrete including close hacking of all exposed
concrete work after removal of form work, all
materials, labour etc. complete as per
Engineer in Charge. (Area of form work in contact
with concrete shall only be measured for payment
& stop boards for construction joints etc. will not be
measured for payment).
104614.00 a) For all type of Structural / RCC elements in
all geometrical shapes .
Sqm
2517.00
Sqm
Providing, erecting, fixing, centering and shuttering

work using plyboard to obtain form finished
concrete surfaces of F3 finish at all heights &
locations including intermediate / multiple staging
for, all geometrical shapes and designs including
chamfers, splays, keys, wedges, props, rails,
bracings, brackets cutting hole for pipes etc.
providing and applying approved form oil to all
concrete and skirting/removal of the same
including finishing by filling form-tie-hole, removal
of fins, ridges and irregularities by grinding filling
air hole with sack rubbed finish, cleaning up of
loose and adhering debrices including all
materials labour etc. complete as per
specification, drawings and as directed by
Engineer in Charge.
T t l f PART I C
(FORM WORK )
Sqm
Sqm
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
RATE
UNIT
PART - I-D : STEEL REINFORCEMENT WORK

21
Reinforcement for RCC work including supplying

steel bars of various diameters as required at site
of work including loading, unloading, transporting,
decoiling, straightening, cutting, bending, placing
in position and binding with 18 gauge, soft drawn
annealed steel binding wire including carrying out
various tests as required etc. all as per
Engineer in Charge (Cost of binding wire shall be
borne by the contractor & shall not be measured
for payment).
2376.00
MT
i) Thermo Mechanically Treated bars of grade

Fe-500D manufactured by SAIL, TATA STEEL,
and RINL.
Total of PART I-D : (STEEL REINF. WORKS )
MT
Rs.
PART - I-E : MASONRY WORK

Notes:a) The contractor shall get approved the samples of bricks
from the Engineer-In- Charge before procurement on large
scale and shall maintain the same for the entire work
b) Necessary openings/ nitches/ cut-outs, wherever required
as per drawings and asked for by the Engineer-In-Charge,
shall be provided by the contractor without any extra cost.
c) One brick wall thickness shall be considered as 250mm
and half brick wall as 125 mm and lesser wall thickness if
any shall be made up to the required dimensions by the
contractor in CM 1:4 to proper line, level and plumb
d) The rate shall include cost of making the brick masonry
to all geometrical shapes and sizes without any extra cost to
the Department.
22
12756.00 Brick masonry in super structure at all floors and

locations using well burnt bricks from approved
Cum
lots of class designation 75 (classification as per
IS 1077-1992 and minimum average compressive
strength not less than 7.50 N/mm2 ) in CM 1:6 in
250mm walls to correct line, level and plumb
including raking out joints, curing, scaffolding etc.
all complete as per specifications, drawings & as
directed by Engineer in Charge
23
Providing brick work 125mm thick in partition

walls, dwarf walls, parapets, under platforms,
curtain walls, fins,external boxing etc. at all floors
and locations as per drawing using well burnt
bi k f
dl t f l
d i
ti 75
Cum
AMOUNT
SN
24
QNTY.
DESCRIPTION OF ITEM
(classification as per IS 1077-1992 and min.
average compressive strength not less than 7.50
N/mm2) in C.M 1:4 to correct line, level & plumb
including scaffolding, raking out joints, curing etc.
all complete as per specifications drawings & as
RATE
19899.00 i) With 125mm.wide and 80mm. thick RCC (1:2:4)

Sqm
stiffeners at every one metre height including
formwork but excluding the cost of steel
reinforcement, which shall be paid under relevant
item.
Sqm
2698.00
Sqm
ii) Without RCC stiffeners for support walls, nitches

etc.
Sqm
250.00
Cum
Providing random rubble masonry with rough

dressed hard stone in superstructure at all floors
and locations in cement mortar 1:6 including
through stone, header stone, bond stone, quoins
etc. well packed including filling the interstices with
smaller stone chips, striking, raking out joints &
finishing the joints, including scaffolding, curing etc.
all complete as per specifications, drawings and
as directed by the Engineer in Charge.
Cum
TOTAL OF PART I-E : Masonry Work

PART -I-F : FLOORING WORK
Notes:a) The floor finish level shall be generally in level matching with the
surrounding floor finish level. No extra payment shall be
entertained for matching the floor differences.
b) Adjustment of levels in thickness of mortar bedding due to
different types of flooring, if any, shall be done by the
contractor without any extra cost to the Department.
c) The contractor shall submit and get approved the sample for
flooring, skirting, dado tiles from Engineer in Charge before bulk
procurement.
d) Pattern & design of flooring/ skirting/ dado shall be approved by
the Engineer in charge before commencement of work.
e) Exposed edges of all natural stones used for the works like
Kotah, Marble, Granite etc.shall be machine cut and shall have
uniform thickness and mirror polished unless otherwise
mentioned.
f) The rate shall include cost of making the flooring to all geometrical
shapes and sizes without any extra cost to the Department.
25
UNIT
Providing & laying at all floors & locations Vitrified

tile marbonate of M/s H & R Johnson of
600x600mm size, having 8.5mm thickness (or
Rs.
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
flooring / skirting / dado / clading at all floors and
location in approved pattern and colour laid over
cement mortar bedding / backing, close jointed
and grouted with white cement slurry and approved
pigment as per manufacturer's specifications,
finished to level, line, slope and plumb, cutting of
tiles, wastage, making openings / cut out if
neccesary, final cleaning of surfaces, curing etc.
complete all as per drawings, specifications & as
12736.00 i) In flooring laid over 20mm thick cement mortar
Sqm
1:4 ( I cement : 4 sand) bedding.
1852.00
Sqm
26
ii) In skirting laid over 12 mm thick CM 1:3

( I cement : 3 sand) backing.
RATE
UNIT
Sqm
Sqm
Providing and laying at all floors and levels

6mm(min.) thick or as per specifications of
approved manufacturer first quality matt finished /
non-slippery ceramic tile flooring /dado/ cladding
as per the approved pattern of H & R Johnson (I)
Ltd laid in cement mortar bedding / backing, close
jointed and grouted with matching cement slurry to
match the colour of the tiles, finished to level, line,
slope and plumb including cutting of tiles, making
openings /cutout if necessary, wastage and final
cleaning of surfaces as required, curing
etc.complete all as per drawings,specifications &
as directed by Engineer in Charge
3218.00
Sqm
i) In Flooring laid over 20mm thick cement mortar

1:4 ( I cement : 4 sand) bedding.
Sqm
170.00
Sqm
ii) In skirting laid over 12 mm thick CM 1:3 ( I

cement : 3 sand) backing.
Sqm
11866.00 iii) In dado/ clading laid over 12 mm thick CM 1:3

(1 cement : 3 sand) backing.
Sqm
27
Sqm
Providing & laying machine cut & machine

polished kotah stone flooring at all floor & location
including stair case landing necessary cement
mortar bedding/ backing, close jointed & grouted
with matching cement slurry and finished to line,
level, curing etc. as required, including cutting of
stone slab, wastage, making cut outs, wherever
required, machine polishing/ hand polishing
(where machine cannot have access) etc.
complete all as per specifications, drawings and
7120.00
Sqm
i) In flooring with machine polished kotah stone

slab of size 575x575x 25mm thick with 20mm
thick cement mortar 1:4 ( I cement : 4 sand)
Sqm
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
ii) In skirting with machine polished kotah stone
slab of size 575x150x20 mm with 12mm thick
cement mortar 1:3 ( I cement : 3 sand) backing.
Sqm
252.00
Sqm
iii) For sloped skirting with 12mm thick cement

mortar 1:3 ( I cement : 3 sand) backing.
Sqm
565.00
Sqm
iv) For window sill with machine polished 25mm

thick single piece kotah stone of 125 mm
approximate width laid over 20mm thick cement
mortar 1:4 ( I cement : 4 sand) bedding including
rounding the exposed edges
Sqm
Providing & laying machine cut and machine

polished kotah stone for treads/ risers / steps etc
as mentioned below, laid over cement mortar
bedding/ backing, close jointed and pointed with
matching cement slurry and finished to line, level
plumb etc. as required, including curing, cutting of
stone slab, making cut outs, wherever required,
wastage etc. to get true square edges and final
hand polishing all as per specifications, drawings
& as directed by the Engineer in Charge.
1215.00 i) For treads 25mm uniform thick in single piece
1200mm approx. laid over 20mm thick cement
Sqm
mortar 1:4 (1 cement:4 sand) bedding, including
providing three Nos. of antiskid grooves &
rounding the edges etc.complete.
30
UNIT
1748.00
Sqm
28
29
RATE
Sqm
595.00
Sqm
ii) For risers 20mm thick in single piece of

1200mm (approx.) length with 12mm thick cement
mortar 1:3 (1 cement : 3 sand) backing.
Sqm
204.00
Sqm
iii) For ramp 25mm uniform thick in single piece of

1200mm (approx.) length laid over 20mm thick
cement mortar 1:3 (1 cement :3 sand) bedding,
Sqm
4038.00
Sqm
Providing machine mixing and laying in approved

panels of 40mm thickness IPS flooring in cement
concrete mix of 1:2:4 using graded stone
aggregate of 12.5 mm max. size with colouring
pigment, at all level, well vibrated, compacted
including providing and fixing 25 mm x 3 mm thick
aluminium dividing strip for panel of about 2 sqm
size, to correct level and finished smooth and
curing including preparation of surface by cleaning,
hacking and exposing aggregate to achieve the
best bond, all complete as per specification
drawing & as directed by Engineer in Charge.
Sqm
Providing, laying and fixing in position thickness
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
polished (mirror polish) granite stone of approved
colour/ shade in flooring/ skirting/ clading/ treads/
risers/ cills etc at all location including necessary
mortar bedding/ backing, close jointed and
grouted with matching cement slurry and finished
to line, level etc., as required including cutting of
stone slabs, wastage, making cutouts, required
pattern in plain/ curved or any geometric shape
and design wherever required, all as per
specifications , drawings and as directed by the
Engineer in charge.
RATE
UNIT
i) In flooring at specified areas with mirror

polished 18mm thick granite stone slab in required
sizes, shade, shape and pattern in plain/ curved or
any geometric shape and including 20mm thick
cement mortar bedding of mix 1:4 (1 cement : 4
coarse sand) including grey cement slurry at 4.40
kg/m2 over bedding and matching slurry with white
cement at 2.20 kg/m2 for grouting the joints.
168.00
Sqm
a) 100% raw silk.
Sqm
116.00
Sqm
b) 100% ruby red.
Sqm
31
32
Providing and laying at all floors pre-cast

hydraulically pressed white colour terrazzo/
mosaic tiles of M/s.GICO Tiles , using marble
chips of size 4 to 10mm with approved colour
(using white cement) in flooring/ skirting over and
including mortar bedding/ backing, close jointed,
double grouting of joints with matching cement
slurry, finished to level, slope and plumb as
required, curing and machine polishing (hand
polishing, where machine cannot have access)
including cutting of tiles if required, wastage etc.,
8165.00
Sqm
i) Flooring with 250 x 250 x 22mm size tiles as per

relevant IS with 20mm thick cement mortar
bedding of mix 1:4 (1 cement : 4 coarse sand)
including grey cement slurry at 4.40 kg/m2 and
white cement slurry at 2.20 kg/m2 over the
bedding and for grouting the joints respectively.
Sqm
916.00
Sqm
ii) Skirting with 100 x 20mm size tiles with

20mm thick cement mortar backing of mix C.M 1:3
(1 cement : 3 coarse sand)
Sqm
Providing, laying and fixing in position machine
AMOUNT
SN
RATE
UNIT
QNTY.
DESCRIPTION OF ITEM
stone of approved colour/ shade in flooring/
skirting/ clading etc. at all location including
necessary mortar bedding/ backing, close jointed
and grouted with matching cement slurry and
finished to line, level etc., as required including
cutting of stone slabs, wastage, making cutouts,
required pattern in plain/ curved or any geometric
shape and design wherever required, all as per
Engineer in charge.
484.00
Sqm
i) In flooring at specified areas with mirror

polished 16 mm thick marble stone slab in required
sizes, shade, shape and pattern in plain/ curved or
any geometric shape and including 20mm thick
cement mortar bedding of mix 1:4 (1 cement : 4
coarse sand) including grey cement slurry at 4.40
kg/m2 over bedding and matching slurry with white
cement at 2.20 kg/m2 for grouting the joints.
Sqm
75.00
Sqm
ii) In skirting with 16 mm thick mirror polished

marble stone over and including 12mm thick
cement mortar 1:3 (1 cement : 3 coarse sand)
backing.
Sqm
Cement plaster 20 mm thick in skirting and risers

to steps with cement mortar 1:3 finished smooth
with a coat of neat cement including rounding of
junction with floor where necessary, curing etc.
complete all as per drawing, specifications & as
Sqm
33
694.00
Sqm
34
Sqm
1740.00 Providing and fixing at all floors & levels, 35 mm
uniform thickness machine cut and machine preSqm
polished on top, bottom & exposed edges,
cuddapah stone shelves including cutting
recesses alround in wall embedding (minimum 25
mm alround) with C.M. 1:3 or in case of concrete
member supported over 40x40x6 mm MS angle to
the correct line, level, curing, making good the
surfaces etc. complete all as per specifications,
drawings and as directed by the Engineer- inCharge. (The cost of MS angle shall be paid
seperately under relevant item.)
Note:i) Only area of exposed top surface shall be measured for payment.
ii) The thickness of cuddapah stone shall be 35mm (+) or (-)
acceptable tolerence. The agency may quote accordingly.
35
925.00
Sqm
Providing and fixing at all floors & levels 35 mm

thick machine cut and machine polished (pre
polished ) cuddapah stone flooring in 20mm thick
CM 1:4 bedding / backing close jointed grouted
Sqm
AMOUNT
SN
QNTY.
36
DESCRIPTION OF ITEM
line,level,curing etc. including cutting the stone
slab,wastage,final cleaning the surface complete
all as per specifications,drawings & as directed by
Engineer in charge.
RATE
UNIT
Providing & laying machine cut machine polished

natural stone verticals/topping/ facia etc.for
kitchen/ wash basin platform as specified below,
over and including necessary mortar
bedding/backing, close jointed and grouted with
matching cement slurry and finished to line, level,
plumb, curing etc. as required including cutting of
stone slabs, wastage, making cut-outs wherever
required etc. all as per specifications, drawings
and as directed by Engineer in Charge
850.00
Sqm
i) Sandwitch type topping of kitchen/ wash basin

platform with combination of jet black granite
(18mm thick) (in one piece) at top & cuddapa
stone (35mm thick) at bottom total thickness with
mortar of about 85mm and width of about 600mm,
machine polished on one side, set in Cement
Mortar 1:3 ( I cement : 3 sand), between the two
slabs with maximum length not less than 3.00 Mts.
(approx.) in single with a separate piece for sink
area required if any including cutting of slab to fix
S.S sink/ wash basin etc. and making recess in
brick wall etc. including necessary cement paste
making good the surfaces and fixing to level, line,
plumb etc. all as per drawings, specification and
Sqm
Note:1 Only top clear exposed area of the combined slab system shall
be measured for payment and area of bottom slab shall not be
measured.
2 The rate shall be inclusive of making necessary recess in
brick wall to provide minimum bearing of 25mm for the sandwich
slab system.
3 The thickness of cuddapah stone shall be 35mm (+) or (-)
250.00
Sqm
ii) For support walls and kitchen/ wash basin

platform fins, facia with Granite minimum 18 mm
thick & about 100 mm wide, machine cut machine
polished (on exposed surface) stone fixed with
approved adhesive with necessary cement paste
etc. all as per drawing & specification and as
iii) Providing machine cut/machine polished ( on
one side) cuddapha stone vertical support, for
kitchen/wash basin platform in two pieces
(sandwich type) of each 35mm uniform thick
Sqm
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
placed back to back with 20mm thick cement
mortar 1:3 of appx. size 675 x 750mm &100mm
total thickness, making recess in brick wall , fixing
in line, level, plumb with a minimum bearing of
25mm in brick wall and floor , making good the
surfaces etc. including necessary cement paste /
slurry all as per drawing & as directed by Engineer
in Charge.
RATE
UNIT
Note:i) The two stones erected for each vertical support shall be
measured as single unit in sqm under this item.
ii) The thickness of cuddapah stone shall be 35mm (+) or (-)
Providing and laying wooden flooring & skirting
kiln seasoned, chemically treated , Pre polished
solid First class Burma Teak Wood flooring of size
100/150mm wide x 1500mm long x 18mm thick
Tounge and grooved planks having UV lacquer
coating of M/s. Euro woods fixed over 12mm thick
W.P. Marine ply over a salwood framing 60 x
45mm @ 600mm c/c in both directions and
alorund ends laid over 5mm thick X 60mm wide
neoprene sheet under entire sub framing for
Auditorium stage, Library etc.including providing
500 micron polythene sheet below and packing
the cellular spaces with 50mm thick expanded
polystyrene (Thermocole) of 48kg/cum on a dry
and leveled PCC subfloor ( to be paid separately)
complete at all levels, leads, screws,nails, anchor
fasteners, drilling holes etc., all as per drawing
and as directed by the Engineer in Charge.
37
Note:- Quoted rate shall hold good for entire flooring

system. No extra measurement and payment
shall be effected on any other accounts.
38
184.00
Sqm
i) Wooden flooring
Sqm
18.00
Sqm
ii) Wooden skirting
Sqm
Providing, laying & fixing precast M-30 grade

interlocking paver blocks of M/s. GICO tiles, 60mm
thick over a layer of 50mm thick stone dust over
well consolidated sub-base including filling the
joints with stone dust etc. including transporting to
site, placing to proper line & level, finishing the top
surfaces with two coats of lacquer finish etc.
complete as per specification, drawing including
cost of all material, labour, tools etc & as directed
by the Engineer in Charge.
Sqm
2500.00
Sqm
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
TOTAL OF PART I-F : Flooring Work
RATE
UNIT
PART I-G : DOORS AND WINDOWS

Notes:a) The items of door frames, window frames shall include sealing the
joints all round with the brick work/ concrete and doors or windows
with approved mastic filler cement grout/ epoxy compound/
polysulphide compound or by any other means whatsoever, by
the contractor at his own cost as directed by the Engineer- inCharge to make the joints watertight.
b) The work contemplated under the item for supplying and fixing
the window/ door frames shall be got done by the contractor
through specialised agencies in the field, approved by the
Department.
c) One sample each of the door frame, shutter and window with all
fittings and fixtures alongwith locking arrangement including
glass panes etc. complete as per schedule of quantities drawing
and specifications should be submitted for preliminary inspection
before procurement on large scale. The contractor shall submit
six copies of shop drawings for windows, ventilators and steel
door with frames showing dimensional details of construction etc.
for approval of the Engineer-in-charge. After preliminary
inspection, the sample should be fixed. Defects etc.if any shall be
rectified to the full satisfaction of the Department and after
obtaining formal approval in writing of Engineer in Charge.
d) Door frames, shutters and the windows to be supplied and fixed
in position should cater the dimensional tolerance of the
openings to an extent of (+/-) 2%. The rates quoted by the
tenderers should hold good for such variation. Test shall be
conducted by the Department for the flush doors as per
IS-2202-1983 Part-I from each consignment and the cost
incurred on this account shall be borne by the contractor.
e) For bonding the flush doors, block boards, ply wood and all types
of wood works, phenol- formaldehyde synthetic resin type
adhesives conforming to IS-848-1957 shall be used.
f) The rate shall include cost of making the doors & windows
including glass etc.in all geometrical shapes and sizes
39
2635.00 Providing & fixing in position 19mm commercial

block board shutters for cupboard, kitchen cabinet
Sqm
etc. bonded with phenolformaldihyde resin shutter
of approved manufacture with teak wood lipping of
size 19mm wide and 20mm thick alround for
cupboards fixing to (frames will be paid under
relevant item) including providing T.W. meeting
styles of size 25 x 19mm shape as shown in the
drawing by cutting/planning if necessary including
labour charges for fixing the fittings and fixtures
(cost of fittings & fixtures will be paid under
relevent item )and painting all over with two coats
Sqm
AMOUNT
73933797.16
SN
QNTY.
40
DESCRIPTION OF ITEM
primer all complete as per specifications and
drawings and as directed by Engineer in charge.
RATE
UNIT
Supplying & fixing in position the following type

solid core block board flush door shutters with
commercial ply facing on both sides conforming to
IS 2202 (latest) with external type second class
teak wood lipping alround, fixing shutters in
position to pressed steel door frames/ wooden
frames/ granite frame works (door frames shall be
paid separately under relevant item) at all floors by
cutting/ planing if necessary including labour for
fixing of the fittings & fixtures as per drawing with
wooden packing pieces if necessary (but
excluding the cost of fittings and fixtures with
screws which shall be paid separately under
relevant item) including painting the shutters all
over with two coats of synthetic enamel paint of
approved make & colour over one coat of
approved primer etc. all complete as per
specifications,drawings & as directed by Engineer
in Charge.
i) 35mm thick single leaf shutter with second class
teak wood lipping of section 35x20mm.
1676.00
Sqm
a) without transfer grill
Sqm
Supplying and fixing 35 mm thick factory made

FRP semi solid wooden core moulded door
shutters of M/s. Fibroplast all floors and location of
approved colour using 1.5mm thick FRP sheet
with extra reinforcement on sides/ edges with
recess for hinges, necessary arrangement suitable
for fixings fittings, fixtures and fasteners, including
supplying and fixing fittings & fixtures, 3
nos.100mmlong, 2.50mm thick stainless steel
approved quality butt hinges with S.S pin & nylon
washers with 2 nos. 150mm long aluminium
handles and 1 nos. of 150mm long aluminium tadi
and 1 nos 100mm long aluminium baby latch
including cutting, assembling, fabricating and fixing
with special self tapping screws to granite frame
work ( to be paid in relevent item) all as per
drawing & manufactures specifications and as
41
1208.00
Sqm
i) For Door type D4 of approximate size

750 x 2100 / 2150mm.
Note:i) Manufacturer shall submit six copies of shop drawing showing the
dimensions, details of construction etc for the approval of
Engineer in Charge.
Sqm
AMOUNT
SN
RATE UNIT
DESCRIPTION OF ITEM
above assembly whenever required and the entire door unit will
be flush with the finished wall (door frame to paid under relevent
item).
iii) Quoted rate shall inclusive of all necessary fittings and fixtures
required for the complete unit.
QNTY.
42
43
Providing & fixing in position folding type

Galvanised pressed steel door for electrical shaft/
panel room etc. at all floor and location of required
sizes for the following made out of 16 gauge of
grade VIII galvanised MS sheets generally
conforming to IS 4351-1976, with two (top &
bottom) horizontal and two vertical members door
frame made out of 16 gauge grade VIII galvanised
MS frames of size 80 x 55mm bent to shape as
required with mechanical jointing at all junctions by
providing 50 x 50 mm angle cleat made with 16G,
G.I sheet one side welded to vertical member and
another side with anchor fasteners and sleeves to
horizontal member for fixing the frame to floor/
ceiling, vertical members fixed to wall with
threaded sleeves of standard quality at 600mm
centre to centre including providing 16 Gauge G.I
sheet, 80mm wide to vertical stiffner at centre to
the full height for each shutter bent to proper shape
and providing 16G. G.I sheet louvers at top/ bottom
with G.I wiremesh as shown in drawing including
providing necessary locking arrangement, 4 nos.
detachable type hinges for each shutter (with bolt
& nut arrangement) including cost of all materials,
labour, drilling cutting, fabricating, welding fixing
fasteners bolts, nuts, washers etc. including
wastages, chasing the brick/ RCC surfaces if
required and making good the same to match with
surrounding finishing, grouting the fasteners
sleeves in CC 1:2:4 to fix the frame over brick wall
etc. and painting all the exposed surfaces of frame
and shutter with two coats of synthetic enamel
paint of approved make and colour over a coat of
approved yellow zinc chromate primer over a coat
of "etch" primer for all surfaces all as per the
drawings, specification and as directed by the
Engineer in Charge.
88.00
Sqm
i) Steel door approx. size 1000 x 2150 mm single

leaf shutter with louvers as per the drawing.
Sqm
15.00
Cum
Providing & fixing in position second class

approved quality teak wood moulded, rebated
frames of 50x50 mm wrought and finished sizes,
conforming to IS : 4021-1967 for cupboard/aust
fan frame etc. at all height and location, including
making holes in concrete/ masonry walls and
providing and fixing MS hold fasts 300x30x3mm
Cum
AMOUNT
SN
QNTY.
RATE
UNIT
Supplying & fixing 30 mm thick single leaf /

double leaf as indicated below factory made
panelled door shutter of approximate size
900mmx2150 mm door type D-2 of approved
manufacture made out of klin seasoned ,
chemically treated approved quality 2nd class
teak wood styles , rails, mullion and top rail 100
mm wide lock rail 150mm wide and bottom rail
250mm vide using 12mm thick Marine ply wood
panels all as per latest IS -1003 (PART-1) and
fixing the shutter in position to the pressed steel
door frames ( door frame shall be paid under the
relevent item) at all floors including planing if
required labour charges for fixing the fittings
fixtuers as perdrawings (but excluding the cost of
fittings&fixtures with screws) paintings the
shutters all over with two coats synthetic enamal
paint of approved make and colour over coat of
approved primer etc. complete as per
specification , drawings and as directed by the
Engineer in charge.
44
708.00
Sqm
45
DESCRIPTION OF ITEM
case of brick work and M S coach screw 100mm
long or equivalent size in case of RCC/ stone
works including painting two coats of bitumastic
paint for all unexposed surfaces coming in contact
with concrete/ brick masonry and painting the
exposed surface with two coats of synthetic
enamel paint of approved make and shade over a
coat of approved primer etc complete all as per
drawing , specification, and as directed by the
Engineer in Charge.
a) single leaf
Providing and fixing factory made 2 hour fire rated
solid core flush door shutters of approximate size
1000/2000 mmX2145mm,as mentioned below of
"Kuttys Promat 55mm thick asbestos free, Fire
and Hot Smoke resistant shutter comprising of two
9mm PROMINA Calcium Silicate Board, with kiln
seasoned chemically treated hard wood internal
timber frame work of nominal size of fire rated
frame of 100mm x 30mm with infill of 96Kg/Cum,
total 30mm thick ceramic fibre reinforced FR
silicate coating on both sides and faced with 3mm
thick water proof commercial ply conforming to IS
5509 Part-I with 2 rows at Fire and Hot smoke
Seal strips 10mmx4mm /active ingradient
8x2.5mm mounted on grooves in the shutter on all
edges except bottom ,shutter shall be
manufactured with exterior quality synthetic
adhesive forming marine ply surfaces as
manufactured by M/s. Kutty and finished with
Sqm
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
design with hot pressed at factory, edges of
shutters shall be provided with 15mm thick external
teakwood lipping etc., all complete as per drawing,
specifications and as directed by by the Engineer
in Charge.
232.00
Sqm
i) Single leaf door shutter up to structural

opening size 1000mm x 2145mm
RATE
ALUMINIUM DOORS & WINDOWS

Notes:- i) The contractor shall submit 6 copies of shop drawings for each
windows, ventilators showing dimension details of construction
etc. for approval of the Engineer - in - charge. and according to
the approved shop drawing a sample of each of windows with all
fittings and fixtures with locking arrangement including glass
panes etc. complete as per schedule of quantities,
specifications and drawings, shop drawing should be submitted
for preliminary inspection for approval. After preliminary
inspection, the sample should be fixed at site to ascertain its
performance. Large scale manufacturing should be taken up
only after rectification of defects in samples as directed to the full
satisfaction of the department and after obtaining formal
approval.
ii) All doors, windows, ventilators section shall be anodised extruded
section of M/s Jindal / M/s Indal /M/s. Aluminax
iii) All fittings / fixtures shall be of approved make / quality and
as approved by Architect.
iv) All dimensions mentioned in the drawing are approximate.
Necessary allowance for fixing over rough ground, and also
necessary allowances for fixing tolerances to be considered
while manufacturing. While manufacturing, actual site
measurement shall be considered. Necessary planing for fixing
the unit has to be carried out by the contractor without any extra
cost to the department. However, rate quoted by the contractor
shall hold good.
v) Payment shall be made per Kg basis.Aluminium sections such
as shutter frames, track window / door frame/beading channel for
glass adjustable louvers etc., shall only be measured linearly as
per actual / finished cutting size nearest to centimetre and
multiplied with sectional weight of the individual section and the
total quantity of aluminium section will be arrived at for payment
without any allowance for wastage.
vi) All glass panes shall be of M/s Modi guard or equivalent
approved manufacture unless otherwise specified. The glasses
will be measured for payment separately under relevant item.
Actual size of the glass fixed in position will be considered for
payment.
vii) Glass panes shall be fixed with approved EPDM gasketting,
beading, to be free from settling. Necessary mastic to be
provided against seepage of rain water.
UNIT
Sqm
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
quality friction hinges.
RATE
UNIT
ix) In case of damage of any existing work, the same has to be

made good/restored to original condition by the contractor at his
own cost.
x) No separate payment shall be made for fittings such as locking
arrangement, hinges,frictionhinges, fittings and fixtures, gasket
etc., Tenderer are required to consider the cost of all fittings,
fixtures, locking arrangement , handles, pegstays, gaskets,
screws, hinges etc., while quoting the rate for unit weight of
aluminium sectins for window / door.
xi) However floor spring, hydraulic door closer if any will be paid
seperately under relavent item.
46
70.00
MT
Supplying and fixing in position at all floors

MT
integrated anodised matt finished [15 micron thick]
of champagne/ equivalent coloured, aluminium
section [extruded] for aluminium doors / windows
sliding / top hung/ fixed / adjustable louvered
windows as per drawing of approved manufactures
with extruded sections of Jindal / Indal / Aluminax
or other approved eqivalent
sections of all geometriccal shape and design with size and weights as
drawing, for frames and shutters [including
wastages if any] conforming to relevant I.S
specifications with all approved champagne
coloured anodised aluminium fittings and
accessories, locking arrangements, 2 / 3 rollers
with ball bearings for sliding shutters of approved
quality all as shown in the drawing, including
providing and fixing aluminium channel beading /
glazing clips fixed with necessary champagne
coloured anodised screws, grouting the gap with
thermocole & polysulphide sealant etc. all
complete generally as per drawings, specifications
etc., all as directed by Engineer-in-charge.
Providing and fixing following type of approved
quality glass panes for doors/windows/ventilators,
of all geometrical shape and design of M/s.
Modiguard, fixing with aluminium frame work
including fixing aluminium channel beading (to be
paid under relevent item)and providing and fixing
with 2 way EPDM gasketing ,to ensure water and
air tightness and neoprene cushions /gasket
accommadated in grooves, necessary bronze
anodised screws etc., all complete generally as
per drawings specifications and as directed by the
Engineer-in-charge.
47
i) Clear float glass

4038.00
Sqm
a) 4mm thick
Sqm
AMOUNT
SN
48
QNTY.
DESCRIPTION OF ITEM
RATE
UNIT
405.00
Sqm
b) 6mm thick
Sqm
230.00
Sqm
c) 8mm thick
Sqm
34.00
MT
Supplying & fixing in position at all floors and

locations approved colour anodised (15 micron
thick), aluminium section for structural glazing etc.
of approved manufactures with extruded sections
of Jindal or other approved equivalent sections
with size and weights as shown in the drawing,
section should be cut to required size and then
colour anodised the facade be fixed to the
structure through powder coated MS brackets and
anchor fasteners, the mullions are to be connected
to bracket by S.S. 304 nut bolts, sufficient
provision be made to allow free movements of
components due to temperature, deflection of
R.C.C. structure etc. without inducing stresses in a
strucutre, including necessary scaffolding etc.
complete all as per specifications, drawing and as
directed by the Engineer-in-charge.
MT
Note:- i) MS brackets and anchor fasteners, S.S. nut

bolts shall not be paid separately.
ii) The detailed design and shop drawing shall be as per BIS
code for required wind pressure IS 875 Part III, and shall consider
for thermal movements, air inflation, water penetration, seismic
movement and structural movement complete as per
specification. Approval of the Engineer in Charge for the
complete design and shop drawing shall be obtained before
commencement of the work..
iii) The contractor should submit the samples for approval
before taking up any actual work at site
Providing and fixing reflective toughned Glass of
thickness as indicated below in approved colour of
M/s Glaverbel, Belgium , Silicon Sealant Structural
Grade and weathering grade shall be DOW
Corning - USA or G.E. Silicon - USA or WACKER
Germany of Silicon byte size as per design
including providing and fixing both side adhesive
tape NORTON make or TROCILLEN and also
using backer foam of TROCILLEN as per drawing
complete as per specification and standard sound
practices using all necessary materialsincluding
scaffolding etc.all complete as per sopecification
drawings and as directed by Engineer-In -Charge
49
416.00
Sqm
i) 8mm thick
Sqm
AMOUNT
SN
QNTY.
RATE
DESCRIPTION OF ITEM
TOTAL OF PART -I-G: DOORS & WINDOWS :
UNIT
PART : I-H : FITTING & FIXTURES:

Notes:- i) One sample board consisting of each item of schedule of
quantities with approved quality fittings & fixtures & necessary
accessories including chromium plated brass screws, bolts, nuts,
washers should be submitted for approval of Engineer-in- charge.
Large scale procurement shall be taken up only after approval of
the Engineer-in-charge. After approval, the samples shall be
kept in the office of the Engineer-in-charge to ascertain the
approved quality for the entire work.
ii) All fittings & fixtures shall conform to relevant IS code.
Supplying at site of work, matt finished anodised
aluminium approved quality fittings, fixtures and
fastenings along with CP brass screws, bolts and
other accessories as per approved samples as
per relevent IS code (Labour charges for fixing will
be paid under relavent items.)
50
1174.00
Nos.
i) Tower bolt: 200mm. long x 12mm, 13mm barrel.
1828.00
Nos.
ii) Tower bolt: 100mm. long
1692.00 iii) Door stopper with rubber bushing (shutter

mounted type)
Nos.
3552.00
Nos.
iv) D - type bow handles 150mm long
624.00
Nos.
v) Tadi (Door latch )200x15x8.50 mm thick flat

with 11x3 mm thick counters
1942.00
Nos.
vi) Rubber buffer
00000
Each
Each
Each
Each
Each
Each
Supplying at project site approved quality non

magnetic stainless steel fittings, fixtures and
fasteners along with necessary SS screws, bolts,
nuts, washers etc. as per approved
samples.(Labour charges for fixing will be paid
under relavent items.)
51
978.00
Nos.
i) Butt Hinges of following sizes

a) 125x45mmx10 gauge
2632.00 b) 125x30mmx10 gauge

Nos.
Each
Each
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
2452.00 ii) Piano Hinges 19mm x 19mm x 20 guage.
Rm
RATE
UNIT
Rm
iii) D - type bow handles

805.00
Nos.
a) 250mm long
Each
366.00
Nos.
b) 150mm long
Each
84.00
Nos.
c) 100mm long
Each
52
Supplying at site of work approved quality brass

fittings and fixtures with brass screws, bolts and
other accessories as per approved samples as
per relevent IS code (Labour charges for fixing will
be paid under relevant items.)
426.00
Nos.
i) Brass handle 125mm long with concealed

brass screw
Each
264.00
Nos.
ii) Brass tower bolt 250mm long with 10mm dia

pin.
Each
116.00
Nos.
iii) Brass tadi (Door latch )200x15x8.50 mm thick flat

with 11x3 mm thick counters
Each
261.00
Nos.
iv) Brass door stopper with rubber bushing (shutter

mounted type)
Each
53
Supplying at site of work approved quality

miscellaneous fittings and fixtures with screws,
bolts and other accessories as per approved
samples as per relevent IS code (Labour charges
for fixing will be paid under relevant items.)
2290
Nos
i) Magnetic ball catches
Each
Each
938.00
Nos
ii) Supplyimg at site bright finished brass

cupboard or wardrobe locks with four levers
including necessary screws ( of approved make)
v) Mortice lock as mentioned below with
chromium plated brass parts & body of Godrej
make with pair of detachable, pressure dia-cast
chromium plated handles on both sides with
chromium plated brass screws for left hand/right
hand with brass socket plated, (exact number for
left, right and double shutter shall be ascertained
based on site requirement) all complete as per
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
specifications & as directed by EIC.
RATE
UNIT
174
Nos
a) Four lever
Each
728
Nos.
b) Six lever
Each
54
464
Nos
Supplying and fixing at all floors and levels IS:3564

marked aluminium extruded section body tubular
type universal hydraulic door closer of M/s. Everite
with double speed adjustment with necessary
accessories and necessary screws etc complete
of Everite all as per specifications and directed by
Engineer-in-Charge.
Each
55
50
Nos
Providing and fixing in position double action floor

spring of M/s. Garnish traders for doors with a set
of double action pivots with outer case including
cutting pockets in concrete floors, making good
the surface to original finish etc., complete all as
per drawing and as directed by
Engineer-in-Charge.
Each
TOTAL OF PART I H : Fittings & Fixtures

PART - I-I ~ WATERPROOFING TREATMENT:
Notes:- a) The contractor shall get written approval from the Engineer- incharge, for the water proofing agency is engaged and shall
submit the specification of the waterproofing agency before
commencement of work.
b) The contractor shall test the surface where water proofing
treatment provided for bone dry condition by filling up with water
.No wet patches or leaks shall appear on the surrounding wall or
under side of the slab
c) The contractor shall furnish guarantee bond on appropriate
stamp paper in the proforma as per Section 10 (iii) conditions
and clauses of contract for the entire waterproofing treatment for
maintaining the surroundings and under side surfaces of the
waterproofing treated area in bone dry condition for 10 years.
During the guarantee period the contractor shall attend all
leakages, defects etc. if noticed, free of cost, starting the work of
checking up and rectification within a week's time from the date of
intimation about such leakages/defects
d) The Contractor shall keep the water tank filled with water after the
water proofing work has been completed and shall clean it before
handing over. At no time shall the water tank be kept empty.
Testing for the bone dry condition for the water proofing work
carried out shall again be done, before handing over the flats, if
found necessary by the Engineer- in-charge.
AMOUNT
SN QNTY.
DESCRIPTION OF ITEM
56 18347.00 Providing and laying integral cement based water
Sqm
proofing treatment of the agency approved by
Department, including preparation of surface as
required for treatment of roofs, balconies, terraces
etc consisting of following operations as per IS :
2645 :2003, with average thickness of 115mm and
minimum thickness at drain point as 65 mm
RATE
UNIT
Sqm
Notes: Following works are included in above item.

i) Applying and grouting a slurry coat of neat
cement using 2.75 kg/sqm. of cement admixed
with proprietory water proofing compound over the
RCC slab including cleaning the surface before
treatment.
ii) Laying cement concrete using broken
bricks/brick bats 25 mm to 100 mm size with 50%
of cement mortar 1:5 (1 cement : 5 coarse sand)
admixed with proprietory water proofing
compound over 20 mm thick layer of cement
mortar of mix 1:5 (1 cement : 5 coarse sand)
admixed with proprietory water proofing
compound to required slope and treating similarly
the adjoining walls upto 300 mm height including
rounding of junctions of walls and slabs.
iii) After two days of proper curing applying a
second coat of cement slurry admixed with
proprietary waterproofing compound.
iv) Finishing the surfaces with 20 mm thick jointless
cement mortar of mix 1:4 (1 cement : 4 coarse
sand)admixed with proprietary water proofing
compound and finally finishing the surface with
towel with neat cement slurry and making of
300 x 300 mm square.
v) The whole terrace so finished shall be flooded
with water for a minimum period of two weeks for
curing and for final test. All above operations to be
done in order and as directed and specified by the
Engineer -in-Charge.
57
630.00
Cum
Extra for additional thickness of brick bat coba

over and above standard average thickness of
115 mm. for effective slope wherever required.
Cum
58
1905.00
Cum
Filling in bath, W/C, toilet, depressed areas

with water proofing brick bat coba of the agency
approved by the Dept. at all floors and locations
upto the required level and making the surface
finished suitable to receive floor finish etc. all
complete as per drawings and water proofing
agency's specifications & as directed by the
Engineer in Charge.
Cum
59
idi
dl
fi
tt
AMOUNT
SN
QNTY.
Sqm
DESCRIPTION OF ITEM
vertical and horizontal surfaces of depressed
portions of W.C., Kitchen and the like consisting of
following
RATE
UNIT
AMOUNT
i) 1st course of applying cement slurry @ 4.4.

Kg/sqm mixed with water proofing compound
`Impermo' of Snowcem conforming to
IS 2645 in recommended proportions.
ii)II nd course of 20mm cement plaster 1:3 (1
cement : 3 coarse sand) mixed with water proofing
compound in recommended proportions.
iii) IIIrd course of applying blown or residual
bitumen applied hot at 1.7 Kg per sqm of area.
iv) IV th course of 400 micron thick PVC sheet
(Overlaps at joints of PVC sheet should be 100 mm
wide and pasted to each other with bitumen @ 1.7
Kg/sqm.)
TOTAL OF PART -I-I ~ Waterproofing Works
22085381.82
PART I - J : PLASTERING WORK :

Notes :- a) Before commencement of plastering, the area shall be cleaned,
wetted and shall be marked with 'Thiyyas' or 'Tapanis' and shall
be got approved by the Engineer-in-charge.
b) Whenever the electrical contractor/ agency has to fix up switch
boxes in walls, necessary Thiyyas or 'Dhadas' shall be
arranged prior to plastering so that the electrical boxes are fixed
properly in line with the finished plastered surfaces.
c) Finishing around the junction boxes shall be done at all floor,
level and position to the line, level and right angles as required
while carrying out plastering work.
d) No extra claim/cement consumption shall be entertained by the
department for the plastering done more than the specified
thickness shown in the schedule of quantities, to bring the
plastered surface to perfect line, level and plumb with adjoining
columns and beams.
Cement plaster in single coat with cement mortar
at all floors, heights, slopes and locations on plain
or curved surfaces including rounding wherever
required including to prepare the surface even and
smooth to correct line, level, plane and plumb
including scaffolding, curing etc. complete as per
Engineer-in-Charge.
60
47358.00
Sqm
i) 6mm thick cement plaster in Cement mortar

(1 cement : 4 fine sand) for ceiling, exposed
concrete surfaces, soffits of of all slabs and beams
soffit of staircase waist slab etc including providing
and adding bonding agent of "DR.FIXIT PIDICRETE
Sqm
SN
QNTY.
DESCRIPTION OF ITEM
recommendation, including applying a slurry coat of
cement and DR.FIXIT PIDICRETE MPB"(1:1 volume
mix) with a brush before plaster applied. internal
brick / concrete surfaces.
RATE
152882.00 ii) 15 mm. thick plaster in CM 1:4 mix for internal
Sqm
80010.00
Sqm
brick / concrete surfaces for all walls and beams

flush with walls, mullions etc.
i) 20 mm. thick in two coats for brick/ concrete

surfaces (external / internal) (back coat and
finishing coat of 10 mm. thick each) with water.
21548.00 ii) 12 mm. thick in single coat for independent

concrete surfaces
Sqm
Sqm
Sqm
Extra over plastering items for making and

finishing in matching plaster finish (interior &
exterior) grooves of following approximate sizes
as per drawing in plaster, at all floors and
locations to proper line, level and plumb all as per
specifications and drawings.
62
64
Sqm
Sand faced external / internal cement plaster as

specified below in cement mortar 1:2 at all heights
and locations including scaffolding, preparing the
surfaces, finishing and rendering with sponge to
correct line, level and plumb, curing complete as
per specifications and drawings and as directed
by the Engineer in Charge.
61
63
UNIT
8538.00
Rm
i) 25 x10mm size
Rm
3316.00
Rm
ii) 10 x 4 mm size
Rm
20392.00 Providing vatas 150 x 150 mm. at junction of

walls and chhajjas, canopies etc. with cement
RM
mortar 1:3 to match the surrounding plaster
including rounding the junction of wall and chajjas/
offset etc. to the required profile including adding
water proofing compound @2% by weight of
cement, scaffolding, curing etc. complete as per
specifications and drawings and as directed by
the Engineer-in- charge.
Making various moulds / bands in C.M. 1:3 as
specified below, in proper line, level, shape and
design as shown in following drawings, fixing
chiken wire mesh (to be paid under relevent item),
preparing surfaces, rendering with sponge,
scaffolding, curing, etc. complete all as per
drawing, specification & as directed by the Engineer in Charge
Rm
AMOUNT
SN
QNTY.
Rm
DESCRIPTION OF ITEM
thick from base plaster as shown in
drawing.
RATE
UNIT
Total of Part -I-J : Plastering Work

PART : I-K ~ PAINTING :
65 191423.00 Providing and applying 1.5mm thick cement base
Sqm
wall care putty in two coats of M/s. Birla White at all
floors and locations, plastered surfaces finished
smooth to correct line level, plain, plumb etc.,
including preparing the surfaces, scaffolding,
smoothen the putty surfaces with very fine water
proof emery paper to get a glossy finish etc.
complete as per specifications, as per
manufacturers specifications, drawing & as
Sqm
66
Sqm
24508.00 White washing in three coats in all floors and

Sqm
locations for ceiling and walls including sand
papering and cleaning the surfaces, filling up
cracks and crevices if any with approved putty,
scaffolding etc. complete all as per specifications
and as directed by the Engineer-in-charge.
67 164286.00 Painting plastered surfaces with two coats of

Sqm
Acrylic emulsion paint of approved colour over a
coat of approved cement primer including
preparing the surfaces, filling with a coat of putty
wherever required scaffolding and cleaning etc,
Sqm
68
3845.00 Painting plastered surfaces with two coats of Oil

Sqm
bound distemper, including preparing the surfaces,
filling with a coat of putty wherever required ,
scaffolding and cleaning etc, complete as per
Engineer-in-charge.
Sqm
69
13015.00 Painting plastered surfaces with two coats of

Sqm
synthetic enamel paint approved colour over a
coat of approved cement primer including
preparing the surfaces, filling with a coat of putty
wherever required scaffolding and cleaning etc,
Sqm
70
Painting external surfaces with two coats of

exterior grade Acrylic emulsion paint of Apex
ultima of M/s.Asian paints of approved colour and
shade over a coat of cement based water
repellent paint of approved make and shade as
mentioned below all as per manufacturer's
AMOUNT
SN
QNTY.
69880.00
DESCRIPTION OF ITEM
sample including providing necessary
scaffolding,cleaning the surface with water to
remove all coating, dust, filling up cracks &
crevices with approved putty, curing the surface
etc. complete as per specifications and as
i) Over sand faced plaster.
RATE
UNIT
Sqm
Sqm
TOTAL OF PART I-K ~ Painting Work
PART : I-L ~ MISCELLANEOUS WORKS
Notes -: One sample of each item should be submitted for preliminary inspection and
approval before procurement /manufacturing on large scale. After the preliminary
inspection and approval, the sample should be fixed at site or kept in the office
of the Engineer-in-charge till completion of the work.
Structural steel work at all floors and locations in

guard bars, grills,guard bars for windows, frames,
pit / trench covers, cover bracket for slanting chajja
, trap door,railing, smoke vents,trusses, dome,
M.S grill / fencing,Gate etc. using angles, tees,
flats, bars ,chequered plates , sheets Channel
sections,M.S tubes/pipes, joists, bolts & nuts etc
at all floors and locations, heights, including
scaffolding, bracing, multi level stagging, lead
etc., including supplying, cutting, fabricating,
welding, erecting, making holes/chases
wherever required and fixing /embedding in
position in concrete/brick work/marble/granite
stone with necessary hold fasts/stainless steel
screws & rawl plugs by drilling etc.and finishing
the concrete/ brick work after fixing/embedding
including painting two coats of anticorrosive
bitumastic paint on all unexposed surfaces and
two coats of synthetic enamel paint of approved
make and colour on all exposed surfaces over a
coat of approved steel primer etc. complete as per
Engineer in Charge.
71
115.00
MT
i) For all structural steel except truss and dome

structrue
Notes:- a) Quoted rate shall be inclusive of all cost

irrespective of size & shapes, in circular/plain
works of steel trussess, structural roof system,
tubular frame works,etc., Extra claim will be not
entertained.
b) The detailed design and shop drawing for
trusses and dome structure shall be as per BIS
MT
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
and shall consider for thermal movements, air
inflation, water penetration, seismic movement
and structural movement complete as per
specification. Approval of the Engineer in Charge
for the complete design and shop drawing shall
be obtained before commencement of the work.
RATE
UNIT
Cement concrete of specified grades at all

locations & heights for the following works using
graded stone aggregate of 20mm maximum size
including necessary form work, machine mixing,
transporting, placing in position, consolidation,
finishing, making required slope, curing etc.
complete as per specifications, drawings & as
72
Notes: - Nominal Reinforcement if provided shall

be measured & paid under relevant item.
684.00
Cum
a) Providing & laying cement concrete coping of

grade M20 over parapet wall, projected fins / facia
etc. as shown in the drawings.
Cum
95.00
Cum
b) P C C of grade M10 in top of steps of

galleries, raised platforms, dias etc.
Cum
135.00
Cum
c) P C C of grade M15 in otlas of kithen/ pantries,

etc.
Cum
73
392.00
Cum
Cement concrete of mix proportion 1:5:10 ( 1

cement : 5 sand : 10 graded brick bat of size
40mm) at all locations & heights for
galleries,raised platforms etc. including necessary
form work, machine mixing, transporting, placing in
position, consolidation, finishing, making required
slope, curing etc. complete as per specifications,
drawings & as directed by the Engineer in
Charge.
Cum
74
13.00
MT
Providing & fixing stainless steel pipe hand rail at

taircase & lobby, all floors & levels conforming to
304 Grade of steel, of Schedule 10-S, having
950mm/ 250mm height approximately, pattern is
40mm/ 35mm & 25 mm dia.NB Pipe in
horizantal,40mm/ 25mm dia NB pipe in verticle
all as per pattern & design shown in drawing
including necessary S.S bend, tees, welding /
nut-bolt necessary anchoring polishing and fixing in
concrete/ brick wall with S.S lugs, making pockets,
concreting, making good the surfaces etc. as per
specifications drawings and as directed by
Engineer in Charge.
MT
75
845.00
R
Providing & fixing 875 mm above RCC Ledge/
Rm
AMOUNT
RATE
UNIT
SN
QNTY.
DESCRIPTION OF ITEM
consisting 50mm dia . NB ''B'' Class (medium
Quality) confirming to relevant IS Code for rail at
top, supported over and including 835 mm long
20x20mm bright bars balusters placed at 100
mm center to center welded at top to the pipe
rail and bottom to 40mmx6mm MS flats (including
cost of M S flat ) and whole unit embedded in
R C C Ledge/ parapet/ bund at bottom and at
both ends in R C C/ brick , with necessary hold
fasts including painting the whole unit with two
coats of synthetic enamel paint of approved
make and colour over a coat of approved steel
primer etc. complete as per specifications drg.
and as directed by the Engineer in charge.
76
845.00
Rm
Providing 150mm high G.I Pipe hand railing at top

of RCC balcony pardi, consisting of 50 mm dia.
N.B. medium quality G.I. Pipe top runner welded to
10mm x 10mm square solid MS twin bar verticals
(balusters) at 65 mm c/c, twin bars equally placed
at 600mm/ 900mm centre to centre or at suitable
distance as shown in drawing, welded & resting on
16mm x 4mm MS flat, fixing the flat to RCC pardi
with suitable screws or hold fasts and concrete/
mortar, top runner embedded in wall 50mm in both
ends including painting with two coats of synthetic
enamel paint of approved make and colour over a
coat of approved primer after applying 'etch' primer
etc. complete all as per specifications, drawing
Rm
77
885.00
Rm
Providing 1000mm high measured above at

centre of finished tread, G.I Pipe hand railing for
staircase, consisting of 50mm dia. N.B. medium
quality G.I. Pipe top rail welded to 25mm x 4mm
MS flat runner which are welded and resting on
20mm x 20mm square solid MS twin bar balusters
at 90mm to 110mm c/c, twin bars equally placed
at 280mm centre to centre or at suitable distance
as shown in drawing, welded & resting on 20mm x
20mm and 65mm long MS square solid lugs,
embeding the lugs 65mm in each side of steps/
side of waist slab, welding the horizontal 16mm
x16mm square solid MS bars at 150mm C/C
between twin balusters including painting with two
coats of synthetic enamel paint of approved make
and colour over a coat of approved primer after
applying 'etch' primer etc. complete all as per
specifications, drawing and as directed by the
Engineer-in-charge.
Rm
78
642.00
Rm
Providing 1000mm high measured above at

centre of finished tread, second class TW hand
railing for staircase, consisting of 75mm deep,
Rm
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
tapered moulded finished section, french polishing
of approved shade and colour of the same with
minimum two coats over approved wood primer,
screwed to 40mm x 4mm MS flat runner which are
welded and resting on 20mm x 20mm square
solid MS bar balusters centre of tread or at
suitable distance as shown in drawing, embeding
the balusters 90mm in each steps by providing the
100mm x100mmx 100m deep pockets and filling
the same by M20 grade conctrete, welding the
three nos. horizontal 20mm x20mm square solid
MS bars at 150mm C/C between balusters and
welding two vertical bars between three horizontals
as shown in drawing, providing aluminium shoe at
bottom of each balusters including painting the
MS bars/ balusters with two coats of synthetic
enamel paint of approved make and colour over a
coat of approved primer after applying 'etch' primer
etc. complete all as per specifications, drawing
RATE
79
11402.00 Providing & fixing in position GI chicken wire mesh

Sqm
(Hexagonal shape) of 12mm size hole, 22 Gauge
with necessary U hooks, clips or nails at all floors
and levels, wherever req ired to p event
development of cracks in plaster surfaces, as per
Engineer in Charge (Only area of chicken mesh provided shall
be measured for payment)
80
2312.00
Sqm
Cement plaster 15mm thick for brick work in

cement mortar 1:4 at all locations including water
proofing agent @ 2% by weight of cement,
preparing the surfaces, finishing with neat coat
cement to correct line, level and plumb, curing etc.
as per specifications and drawings.
UNIT
Sqm
Sqm
Providing and fixing 'B' class (medium quality) GI

pipe for sleeves and spouts etc at floors and
locations including cutting of pipes as required,
bending and embedding in masonry/ concrete
work or burrying underground with necessary
cement mortar making good the surfaces,
finishing/ cleaning etc. complete as per
Engineer-in-charge.
81
184.00
Rm
316.00
Rm
416.00
Rm
i) 40 mm. dia. N.B.
290.40
Rm
ii) 50 mm. dia. N.B.
363.00
Rm
iii) 75 mm. dia. N.B.
607.20
Rm
AMOUNT
RATE
UNIT
SN
QNTY.
Nos.
DESCRIPTION OF ITEM
carrying capacity at all locations including cutting
of bars of size as per design requirement, bending
and embedding in masonry/ concrete work or
providing MS square/ rectangular plates of
required thickness as per design requirement,
fixing with anchor bolts with necessary etc.
complete as per specifications, drawings & as
83
1478.00
Sqm
Providing and fixing 50mm thick bitumen

impregnated fibre board of Shalitex for expansion
joint in RCC columns, beams etc. to the full depth
including providing bituminous primer to the
exposed edges of fibre board as per
manufacturers specifications to correct line, level
including cost of all materials, labour etc. complete
all as per specifications, drawings and as directed
by the Engineer-in-charge.
Sqm
84
13.00
Sqm
Providing & fixing DESIGNER partly fixed & partly

openable griled double leaf shutter door of overall
size of 2750mm x 2100mm made out of second
class Burma Teak Wood door frame of size
65x125 mm on wall side and 75mm x 125mm on
openable shutter side with overall size 750mm x
2000mm fixed glazing with 6mm thick clear float
glass on either side of openable double leaf
shutter, providing and fixing 38mm thick second
class Burma Teak Wood double leaf panel shutter
glazed with 6mm thick clear float glass overall size
of 1250mm x 2100mm including providing grills in
four parts of 12mm x 12mm MS square bars
verticles welded to 4mm thick and 16mm wide MS
flat alround peripheral frames as shown in detailed
drawing, fixing the grills to thte frmes and sh
providing and fixing six numbers of MS hold fast of
size 300x30x6mm fixed firmly to the door frame,
moulding out leaf shutter of door into two fold in
equal parts or as shown in the drawingNo.
2009033/AR/MISC.-101 with styles & top rail of
size 125mmx40 mm, bottom rail of size 160x40
mm including providing and fixing 6 mm thick clear
float glass of M/s Modi Guard including the cost of
teak wood moulding patti/ beading, pasting
laminated ply pieces on bottom glazing both side,
applying one coat of Melamine polish finish (
Glossy/ matt) on all surfaces of wood/ veneer etc.,
after polishing with three or more coats of
approved French polish over a coat of wood filler
including sand papering [till to get very smooth
finish by using different grades of sand paper]
cleaning , filling of holes and crevices if any with
putty and matching teak wood powder etc.,
including preparation of base coat of approved
Sqm
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
surfaces due to planning with approved putty to
match the adjoining surfaces etc. embedding the
hold fast into cement concrete of M15 grade after
fixing the door frame in position. complete all
specifications drawings & as directed by Engineer
in Charge.
RATE
UNIT
Note :- i) The rate includes cost of Teak Wood door frame, shutters and
beadings etc.
ii) The MS grill and glass panes shall be measured under
relevant items.
iii) The fittings & fixtures shall be measured under relevant items.
85 14732.00 Providing and fixing in position Gypsum Board
False Ceiling / vertical masking of M/s India
Sqm
Gypsum at all floors, locations & height, including
providing and fixing suspended matel frame work,
mouded out by power pressed MS sheet sections,
galvanized in accordance with zinc coating 120 as
per IS 277 all as per manufacturer's specifications
including the cost of all material, labour, wastage,
scafollding, tools and plants, consisting the follwing
items of work.
a) Soffit Cleat:- Consisting of angle cleats of size
25x35x1.6 mm thick fixed at 600 mm along main
runner (Ceiling Section) direction and 1200 mm
c/c along tube section direction, including
drilling / fixing anchor fastner 12mm dia. X 38mm to
ceiling "Arrow" make
b) Ceiling Section (Main Section) : - 0.55 mm thick
GI sheet profiled to U shape of size 40x35x35 mm
to fix gypboard having knurled web of 40mm and
two equal flanges of 35mm with lips of 8.5mm
(placing of 600mm c/c and fixing the same to Tube
Sections with the help of connecting clips.
c) Tube Section (Intermediate Section):- The
suspending Tube section of size 18x40x0.8 mm
thick with the help of level adjuster made of metal
50x25 mm from soffit at 1200 mm centre with MS
flat 25x3 mm thick fixed to soffit as a hanger with
GI cleat and level adjuster.
d) Wall Angle (Perimeter angle):- Wall angle of
size 25x25 mm and 0.55 mm thick running all
along the perimetre of wall and fixed with nylon
sleeves and screws at 450 mm center to center.
e) Connecting clip:- Clip of 2.64 mm dia to connect
"U" section and Tube section.
f) Level adjuster:- Adjuster of size 20x50 mm to
Sqm
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
RATE
UNIT
ceiling.
g) Gyp Board:- 12.5 mm thick Gypsum board of
M/s. India Gypsum generally as per (GS-GLC 4.7)
with tapered edge MR Ultra Gypboard
conformimg to IS 2095-1982 and fixing the
gypboard to the tube section with screws at 250
mm interval jointing, finishing, champhering the
edge with paper tape and jointing compound
including making opening for light fittings, grills,
diffusers, cutouts, making trap doors at suitable
interval etc. and providing additional frame around
the same all as per manufacturer's specifications.
Note : i) Surface exposed area of soffit in plan shall only be measured in
Sqm. For payment and no deduction shall be made for openings
for grills, ducts, lighting fixtures, diffusers, cutouts etc.
ii) The additional frame works etc. if any for vertical masking and
trap door etc. shall be measured in this item without any extra
cost.
iii) The false ceiling and vertical masking alongwith stepped if any
shall be measured and paid under this item
86
184.00
Sqm
Supplying, laying & fixing 500 micron thick

Polythene sheet including 100 mm wide overlaps
at joints and pasted to each other with approved
adhesive compound including preparing the
existing surfaces, necessary scaffolding and
testing the water tightness and rectification of
defects etc. all complete as per drawing,
specification, and as directed by the Engineer in
Charge.
Sqm
87
200.00
Sqm
Providing and fixing 20mm thick Khondolite stone

work & granite stone at all floors and locations in
combination comprising of 10% Khondolite, 70%
flame finish Ruby Red granite and 20% polished
Ruby Red granite laid over 20mm thick cement
mortar 1:4 (1 cement : 4 coarse sand) including
pointing in white cement mortar 1:2 (1 white
cement : 2 stone dust) with an admixture of
pigment matching the stone shade cutting to size,
polishing, curing etc all complete all as per drawing
and as directed by the Engineer in Charge.
Supplying and laying pea gravel of 200 mm
thick using Non-cohesive/ well gravel hand packed
set in regular lines, levels etc. complete. as per
Engineer- in- charge.
Sqm
88
125.00
Sqm
442.00
89
Providing and fixing 25mm thick Khondolite stone
Cum
Sqm
AMOUNT
SN
QNTY.
DESCRIPTION OF ITEM
20mm thick cement mortar 1:4 including pointing
RATE
UNIT
in white cement mortar 1:2 (1 white cement : 2 stone

dust) with an admixture of pigment matching the
stone shade at all location,incutting cutting, polishing
etc all complete as per drawings and as directed by
the Engineer inCharge.
Total of PART I - L : MISCELLANEOUS WORKS
Rs.
AMOUNT

(381611313) BOQ Earthwork

Uploaded by

Copyright:

Available Formats

(381611313) BOQ Earthwork

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

(381611313) BOQ Earthwork

Uploaded by

Copyright:

Available Formats

Construction of Residential & Amenities, Services and Road

for National Thermal Power Corporation

PART - I CIVIL WORKS

Super structure (Structural)

Doors and windows

Fittings & Fixtures

Water proofing work

PART I-A - SUB STRUCTURE

Cement concrete of specified grades at all

Nominal reinforcement if provided

(i) P C C in Grade M10 in bed concrete to

(ii) P C C in Grade M15 in sub base flooring,

NOTES FOR REINFORCED CEMENT CONCRETE

PPC/ blended cement of ISI marked shall only be used for

All RCC work shall be controlled concrete unless otherwise

The rates for RCC works shall be exclusive of cost of

All coarse aggregate to be of 20mm. maximum size &

Spacers to maintain clear cover for reinforcement.

Reinforced Cement Concrete of fillowing grades in

i) Area of form work in contact with concrete shall only be

any other curved surfaces.

i) Thermo Mechanically Treated bars of grade

Brick masonry work in foundation and plinth,cable

Note:- i)One brick wall thickness shall be considered as 250 mm &

Cement pointing to random rubble masonry wall

Providing random rubble masonry with rough

a) Raised and cut pointing

Filling in plinth with selected earth excavated

Disposing off the surplus excavated materials by

Providing and laying dry rubble stone hard core

Supplying and spreading pesticides

member of Indian Pest Control Association, approved by Central

Providing and laying damp proof course 38mm

Providing and laying patent box type cement

a) Providing 50 mm to 70mm thick water proofing

iii) Finishing top with stone aggregate of 10mm to

PART I-B : SUPER-STRUCTURE (STRUCTURAL)

Reinforced cement concrete of grade as

17895.00 Extra over item 21 (i) ) above for providing RMC

TOTAL OF PART I-B : [ Super Structure ~ Structural ]

PART - I-C : FORM WORK

Providing, erecting, fixing in position, striking /

Providing, erecting, fixing, centering and shuttering

PART - I-D : STEEL REINFORCEMENT WORK

Reinforcement for RCC work including supplying

i) Thermo Mechanically Treated bars of grade

PART - I-E : MASONRY WORK

12756.00 Brick masonry in super structure at all floors and

Providing brick work 125mm thick in partition

19899.00 i) With 125mm.wide and 80mm. thick RCC (1:2:4)

ii) Without RCC stiffeners for support walls, nitches

Providing random rubble masonry with rough

TOTAL OF PART I-E : Masonry Work

Providing & laying at all floors & locations Vitrified

ii) In skirting laid over 12 mm thick CM 1:3

Providing and laying at all floors and levels

i) In Flooring laid over 20mm thick cement mortar

ii) In skirting laid over 12 mm thick CM 1:3 ( I

11866.00 iii) In dado/ clading laid over 12 mm thick CM 1:3