Scribd
Upload
433 views1 page

Assignments On Prestressed Concrete

This document contains 8 paragraphs describing problems related to prestressed concrete beams. The problems provide information on the beam geometry, applied loads, prestressing details like cable profile and force, and ask to calculate stresses, deflections, pressure line locations or cable profile. The questions require analysis of prestressed concrete beams under the effects of self-weight, live loads, and prestress using concepts like stress, force, or load balancing.

Uploaded by

ourebooks
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
433 views1 page

Assignments On Prestressed Concrete

This document contains 8 paragraphs describing problems related to prestressed concrete beams. The problems provide information on the beam geometry, applied loads, prestressing details like cable profile and force, and ask to calculate stresses, deflections, pressure line locations or cable profile. The questions require analysis of prestressed concrete beams under the effects of self-weight, live loads, and prestress using concepts like stress, force, or load balancing.

Uploaded by

ourebooks
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

1.

A rectangular concrete beam of cross-section 300 mm deep and 200 mm wide is prestressed
by means of 15 wires of 5 mm diameter located 65 mm from the bottom of the beam and 3
wires of diameter of 5 mm, 25 mm from the top. Assuming the prestress in the steel as 840
N/mm2, calculate the stresses at the extreme fibers of the mid-span section when the beam
is supporting its own weight over a span of 6 m. If a uniformly distributed live load of 6
kN/m is imposed, evaluate the maximum working stress in concrete. The density of
concrete is 24 kN/m3
2. A concrete beam of 10 m span, 100 mm wide and 300 mm deep, is pre-stressed by 3 cables.
The area of each cable is 200 mm2 and the initial stress in the cable is1200 N/mm2. Cable
1 is parabolic with an eccentricity of 50 mm above the centroid at the supports and 50 mm
below at the center of span. Cable 2 is also parabolic with zero eccentricity at supports and
50 mm below the centroid at the center of span. Cable 3 is straight with uniform eccentricity
of 50 mm below the centroid. If the cables are tensioned from one end only, estimate the
percentage loss of stress in each cable due to friction. Assume = 0.35 and k= 0.015 per m.
3. A prestressed concrete beam with a rectangular section 120 mm wide by 300 mm deep
supports a uniformly distributed load of 4 kN/m, which includes the self weight of the
beam. The effective span of the beam is 6 m. The beam is concentrically prestressed by cable
carrying a force of 180 kN. Locate the position of the pressure line in the beam.
4. A rectangular concrete beam 250 mm wide by 300 mm deep is prestressed by a force of 540
kN at a constant eccentricity of 60 mm. The beam supports a concentrated load of 68 kN at
the centre of the span of 3 m. Determine the location of the pressure line at the centre,
quarter span and support sections of the beam. Neglect the self weight of the beam.
5. A concrete beam with a single overhang is simply supported at A and B over a span of 8 m
and the overhang BC is 2 m. The beam is of rectangular section 300 mm wide 900 mm deep
and supports a uniformly distributed live load of 3.5 kN/m over the entire length in
addition to its self-weight. Determine the profile of the prestressing cable with an effective
force of 500 kN which can balance the dead and live loads on the beam. Sketch the profile
of the cable along the length of the beam. The single overhang beam ABC supporting the
UDL is shown in the figure below.
6. A concrete beam with cross-sectional area of 32 x 103 mm2 and the radius of gyration of 72
mm is prestressed by a parabolic cable carrying an effective stress of 1000 N/mm2. The
span of the beam is 8 m. The cable, composed of 6 wires of 7mmdiameter, has an
eccentricity of 50 mm at the centre and zero at the supports. Neglecting all losses, find the
central deflection of the beam as follows: a) self-weight + prestress, b) self-weight +
prestress + live load of 2 kN/m.
7. A simply supported prestressed concrete beam with a rectangular section 400 mm wide by
600 mm deep supports a uniformly distributed load of 30 kN/m in addition to its selfweight. The effective span of the beam is 10 m. The beam is prestressed by cable having a
parabolic profile with a force of 1740 kN. The cable is anchored at the cg of the cross section
at the supports and has a dip of 160 mm at the mid span. Analyse the beam for the effects
of loads and prestress at the mid span using a) stress concept, b) force concept.
8. A simply supported prestressed concrete beam with a rectangular section 400 mm wide by
600 mm deep supports a uniformly distributed load of 30 kN/m in addition to its self
weight. The effective span of the beam is 10 m. The beam is prestressed by cable having a
parabolic profile with a force of 1740 kN. The cable is anchored at the cg of the cross section
at the supports and has a dip of 160 mm at the mid span. Analyse the beam for the effects
of loads and prestress at the mid span using load balancing concept.

You might also like