Product Name: MOBIL DTE 746

Revision Date: 20 Feb 2012

Page 1 of 9
______________________________________________________________________________________________________________________

MATERIAL SAFETY DATA SHEET

SECTION 1
PRODUCT AND COMPANY IDENTIFICATION
PRODUCT
Product Name: MOBIL DTE 746
Product Description:
Base Oil and Additives
Product Code:
201560302017, 607226
Intended Use:
Turbine oil

COMPANY IDENTIFICATION
Supplier:

Lubes Direct Pty Ltd (New South Wales)

A.B.N. 72 117 841 308
174 Coreen Avenue
Penrith, New South Wales 2750
Australia

24 Hour Environmental / Health Emergency Telephone

Supplier General Contact
Supplier:

Perkal Pty Ltd Trading as Statewide Oil (Western Australia)

A.B.N. 43 009 283 363
14 Beete Street
Welshpool, Western Australia 6106
Australia

24 Hour Environmental / Health Emergency Telephone

Product Technical Information
Supplier General Contact
Supplier:

(8:00am to 4:30pm Mon to Fri)

1300 919 904

(08) 9350 6777

(08) 9350 6777

Perkal Pty Ltd Trading as Roto Oil (South Australia)

A.B.N. 43 009 283 363
6-10 Streiff Rd
Wingfield, South Australia 5013
Australia

24 Hour Environmental / Health Emergency Telephone

Product Technical Information
Supplier General Contact
Supplier:

1300 919 904

1300 458 237

(8:00am to 4:30pm Mon to Fri)

1300 919 904

(08) 8359 8995

(08) 8359 8995

East Coast Lubes Pty Ltd (Queensland and Northern Territory)

A.B.N. 37 117 203 611
Cnr North and Mort Streets
Toowoomba, Queensland 4350
Australia

24 Hour Environmental / Health Emergency Telephone

1300 131 001

Supplier General Contact

1800 069 019
Supplier:

Southern Cross Oil Pty Ltd Trading as Southern Cross Lubes (Victoria and Tasmania)
A.B.N. 43 121 686 253
1/121 Fairbairn Road

Product Name: MOBIL DTE 746

Revision Date: 20 Feb 2012
Page 2 of 9
______________________________________________________________________________________________________________________

Sunshine, Victoria 3020

24 Hour Environmental / Health Emergency Telephone
Product Technical Information
Supplier General Contact

SECTION 2

Australia
1300 131 001
1300 466 245
1300 552 861

HAZARDS IDENTIFICATION

HAZARD CLASSIFICATION: NON-HAZARDOUS SUBSTANCE. NON-DANGEROUS GOOD.

Classified in accordance with Approved Criteria for Classifying Hazardous Substances NOHSC:1008 & according to
Australian Dangerous Goods Code.
POISON SCHEDULE NUMBER:

None Allocated.

AS1940 COMBUSTIBLE CLASS: C2

HEALTH HAZARDS
Low order of toxicity. Excessive exposure may result in eye, skin, or respiratory irritation. High-pressure
injection under skin may cause serious damage.

NOTE: This material should not be used for any other purpose than the intended use in Section 1 without expert
advice. Health studies have shown that chemical exposure may cause potential human health risks which may vary
from person to person.

SECTION 3

COMPOSITION / INFORMATION ON INGREDIENTS

No Reportable Hazardous Substance(s) or Complex Substance(s).

hazardous up to 100%.
SECTION 4

Other ingredients determined not to be

FIRST AID MEASURES

INHALATION
Remove from further exposure. For those providing assistance, avoid exposure to yourself or others. Use
adequate respiratory protection. If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seek
immediate medical assistance. If breathing has stopped, assist ventilation with a mechanical device or use
mouth-to-mouth resuscitation.
SKIN CONTACT
Wash contact areas with soap and water. If product is injected into or under the skin, or into any part of the
body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately by
a physician as a surgical emergency. Even though initial symptoms from high pressure injection may be minimal
or absent, early surgical treatment within the first few hours may significantly reduce the ultimate extent of
injury.

Product Name: MOBIL DTE 746

Revision Date: 20 Feb 2012
Page 3 of 9
______________________________________________________________________________________________________________________

EYE CONTACT
Flush thoroughly with water. If irritation occurs, get medical assistance.
INGESTION
First aid is normally not required. Seek medical attention if discomfort occurs.

SECTION 5

FIRE FIGHTING MEASURES

EXTINGUISHING MEDIA
Appropriate Extinguishing Media: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish
flames.
Inappropriate Extinguishing Media: Straight streams of water
FIRE FIGHTING
Fire Fighting Instructions: Evacuate area. Prevent run-off from fire control or dilution from entering streams,
sewers or drinking water supply. Fire-fighters should use standard protective equipment and in enclosed
spaces, self-contained breathing apparatus (SCBA). Use water spray to cool fire exposed surfaces and to
protect personnel.
Hazardous Combustion Products: Smoke, Fume, Aldehydes, Sulphur oxides, Incomplete combustion
products, Oxides of carbon
FLAMMABILITY PROPERTIES
Flash Point [Method]: >215C (419F) [ASTM D-92]
Flammable Limits (Approximate volume % in air): LEL: 0.9
Autoignition Temperature: N/D

SECTION 6

UEL: 7.0

ACCIDENTAL RELEASE MEASURES

NOTIFICATION PROCEDURES
In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable
regulations.
PROTECTIVE MEASURES
Avoid contact with spilled material. See Section 5 for fire fighting information. See the Hazard Identification
Section for Significant Hazards. See Section 4 for First Aid Advice. See Section 8 for advice on the minimum
requirements for personal protective equipment. Additional protective measures may be necessary, depending
on the specific circumstances and/or the expert judgment of the emergency responders. For emergency
responders:
SPILL MANAGEMENT
Land Spill: Stop leak if you can do so without risk. Recover by pumping or with suitable absorbent.

Product Name: MOBIL DTE 746

Revision Date: 20 Feb 2012
Page 4 of 9
______________________________________________________________________________________________________________________

Water Spill: Stop leak if you can do so without risk. Confine the spill immediately with booms. Warn other
shipping. Remove from the surface by skimming or with suitable absorbents. Seek the advice of a specialist
before using dispersants.
Water spill and land spill recommendations are based on the most likely spill scenario for this material; however,
geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction and
speed may greatly influence the appropriate action to be taken. For this reason, local experts should be
consulted. Note: Local regulations may prescribe or limit action to be taken.
ENVIRONMENTAL PRECAUTIONS
Large Spills: Dyke far ahead of liquid spill for later recovery and disposal. Prevent entry into waterways,
sewers, basements or confined areas.

SECTION 7

HANDLING AND STORAGE

HANDLING
Prevent small spills and leakage to avoid slip hazard. Material can accumulate static charges which may
cause an electrical spark (ignition source). When the material is handled in bulk, an electrical spark could ignite
any flammable vapors from liquids or residues that may be present (e.g., during switch-loading operations).
Use proper bonding and/or earthing procedures. However, bonding and earthing may not eliminate the hazard
from static accumulation. Consult local applicable standards for guidance. Additional references include
American Petroleum Institute 2003 (Protection Against Ignitions Arising out of Static, Lightning and Stray
Currents) or National Fire Protection Agency 77 (Recommended Practice on Static Electricity) or CENELEC
CLC/TR 50404 (Electrostatics - Code of practice for the avoidance of hazards due to static electricity).
Static Accumulator: This material is a static accumulator.
STORAGE
The container choice, for example storage vessel, may effect static accumulation and dissipation. Do not store in open
or unlabelled containers. Keep away from incompatible materials.
Material is defined under the National Standard [NOHSC:1015] Storage and Handling of Workplace Dangerous Goods.
SECTION 8

EXPOSURE CONTROLS / PERSONAL PROTECTION

Exposure limits/standards for materials that can be formed when handling this product:
NOTE: Limits/standards shown for guidance only. Follow applicable regulations.
Biological limits
No biological limits allocated.
ENGINEERING CONTROLS

Product Name: MOBIL DTE 746

Revision Date: 20 Feb 2012
Page 5 of 9
______________________________________________________________________________________________________________________

The level of protection and types of controls necessary will vary depending upon potential exposure conditions.
Control measures to consider:
No special requirements under ordinary conditions of use and with adequate ventilation.
PERSONAL PROTECTION
Personal protective equipment selections vary based on potential exposure conditions such as applications,
handling practices, concentration and ventilation. Information on the selection of protective equipment for use
with this material, as provided below, is based upon intended, normal usage.
Respiratory Protection: If engineering controls do not maintain airborne contaminant concentrations at a
level which is adequate to protect worker health, an approved respirator may be appropriate. Respirator
selection, use, and maintenance must be in accordance with regulatory requirements, if applicable. Types of
respirators to be considered for this material include:
Particulate
No special requirements under ordinary conditions of use and with adequate ventilation.
For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode.
Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate,
gas/vapour warning properties are poor, or if air purifying filter capacity/rating may be exceeded.
Hand Protection: Any specific glove information provided is based on published literature and glove
manufacturer data. Glove suitability and breakthrough time will differ depending on the specific use conditions.
Contact the glove manufacturer for specific advice on glove selection and breakthrough times for your use
conditions. Inspect and replace worn or damaged gloves. The types of gloves to be considered for this material
include:
Nitrile,Viton
No protection is ordinarily required under normal conditions of use.
Eye Protection: If contact is likely, safety glasses with side shields are recommended.
Skin and Body Protection: Any specific clothing information provided is based on published literature or
manufacturer data. The types of clothing to be considered for this material include:
No skin protection is ordinarily required under normal conditions of use. In accordance with good
industrial hygiene practices, precautions should be taken to avoid skin contact.
Specific Hygiene Measures: Always observe good personal hygiene measures, such as washing after
handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective
equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned.
Practise good housekeeping.
ENVIRONMENTAL CONTROLS
Comply with applicable environmental regulations limiting discharge to air, water and
soil. Protect the environment by applying appropriate control measures to prevent or limit
emissions.

SECTION 9

PHYSICAL AND CHEMICAL PROPERTIES

Note: Physical and chemical properties are provided for safety, health and environmental considerations only
and may not fully represent product specifications. Contact the Supplier for additional information.

Product Name: MOBIL DTE 746

Revision Date: 20 Feb 2012
Page 6 of 9
______________________________________________________________________________________________________________________

GENERAL INFORMATION
Physical State: Liquid
Colour: Amber
Odour: Characteristic
Odour Threshold: N/D
IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION
Relative Density (at 15 C): 0.86
Flash Point [Method]: >215C (419F) [ASTM D-92]
Flammable Limits (Approximate volume % in air): LEL: 0.9 UEL: 7.0
Autoignition Temperature: N/D
Boiling Point / Range: > 316C (600F)
Vapour Density (Air = 1): > 2 at 101 kPa
Vapour Pressure: < 0.013 kPa (0.1 mm Hg) at 20 C
Evaporation Rate (n-butyl acetate = 1): N/D
pH: N/A
Log Pow (n-Octanol/Water Partition Coefficient): > 3.5
Solubility in Water: Negligible
Viscosity: 45.3 cSt (45.3 mm2/sec) at 40 C | 6.8 cSt (6.8 mm2/sec) at 100C
Oxidizing Properties: See Hazards Identification Section.
OTHER INFORMATION
Freezing Point: N/D
Melting Point: N/A
Pour Point:
-15C (5F)
DMSO Extract (mineral oil only), IP-346:

SECTION 10

< 3 %wt

STABILITY AND REACTIVITY

STABILITY: Material is stable under normal conditions.

CONDITIONS TO AVOID: Excessive heat. High energy sources of ignition.
INCOMPATIBLE MATERIALS: Strong oxidisers
HAZARDOUS DECOMPOSITION PRODUCTS: Material does not decompose at ambient temperatures.
HAZARDOUS REACTIONS: Will not occur.
SECTION 11

TOXICOLOGICAL INFORMATION

ACUTE TOXICITY
Route of Exposure

Conclusion / Remarks

Inhalation
Toxicity (Rat): LC50 > 5000 mg/m3

Minimally Toxic. Based on test data for structurally similar materials.

Irritation: No end point data.

Negligible hazard at ambient/normal handling temperatures. Based

on assessment of the components.

Product Name: MOBIL DTE 746

Revision Date: 20 Feb 2012
Page 7 of 9
______________________________________________________________________________________________________________________

Ingestion
Toxicity (Rat): LD50 > 5000 mg/kg

Minimally Toxic. Based on test data for structurally similar materials.

Skin
Toxicity (Rabbit): LD50 > 5000 mg/kg

Minimally Toxic. Based on test data for structurally similar materials.

Irritation (Rabbit): Data available.

Negligible irritation to skin at ambient temperatures. Based on test

data for structurally similar materials.

Irritation (Rabbit): Data available.

May cause mild, short-lasting discomfort to eyes. Based on test data

for structurally similar materials.

Eye

CHRONIC/OTHER EFFECTS
Contains:
Base oil severely refined: Not carcinogenic in animal studies. Representative material passes IP-346, Modified
Ames test, and/or other screening tests. Dermal and inhalation studies showed minimal effects; lung nonspecific infiltration of immune cells, oil deposition and minimal granuloma formation. Not sensitising in test
animals.
Additional information is available by request.
IARC Classification:
The following ingredients are cited on the lists below: None.

1 = IARC 1

SECTION 12

--REGULATORY LISTS SEARCHED-2 = IARC 2A

3 = IARC 2B

ECOLOGICAL INFORMATION

The information given is based on data available for the material, the components of the material, and similar materials.
ECOTOXICITY
Material -- Not expected to be harmful to aquatic organisms.
MOBILITY
Base oil component -- Low solubility and floats and is expected to migrate from water to the land. Expected to
partition to sediment and wastewater solids.
PERSISTENCE AND DEGRADABILITY
Biodegradation:
Base oil component -- Expected to be inherently biodegradable
BIOACCUMULATION POTENTIAL
Base oil component -- Has the potential to bioaccumulate, however metabolism or physical properties may
reduce the bioconcentration or limit bioavailability.

Product Name: MOBIL DTE 746

Revision Date: 20 Feb 2012
Page 8 of 9
______________________________________________________________________________________________________________________

SECTION 13

DISPOSAL CONSIDERATIONS

Disposal recommendations based on material as supplied. Disposal must be in accordance with current applicable
laws and regulations, and material characteristics at time of disposal.
DISPOSAL RECOMMENDATIONS
Product is suitable for burning in an enclosed controlled burner for fuel value or disposal by supervised
incineration at very high temperatures to prevent formation of undesirable combustion products.
Empty Container Warning Empty Container Warning (where applicable): Empty containers may contain residue and
can be dangerous. Do not attempt to refill or clean containers without proper instructions. Empty drums should be
completely drained and safely stored until appropriately reconditioned or disposed. Empty containers should be taken
for recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance with
governmental regulations. DO NOT PRESSURISE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE
SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION.
THEY MAY EXPLODE AND CAUSE INJURY OR DEATH.
SECTION 14
TRANSPORT INFORMATION
LAND (ADG) : Not Regulated for Land Transport
SEA (IMDG): Not Regulated for Sea Transport according to IMDG-Code
AIR (IATA): Not Regulated for Air Transport

SECTION 15

REGULATORY INFORMATION

Material is not hazardous as defined by the Approved Criteria for Classifying Hazardous Substances NOHSC:1008.
Product is not regulated according to Australian Dangerous Goods Code.
No Poison Schedule number allocated by the Standard for the Uniform Scheduling of Medicines and Poisons (SUSMP)
established under the Therapeutic Goods Act.
REGULATORY STATUS AND APPLICABLE LAWS AND REGULATIONS
Complies with the following national/regional chemical inventory requirements: IECSC, PICCS, ENCS,
TSCA, EINECS, DSL, AICS, KECI

Product Name: MOBIL DTE 746

Revision Date: 20 Feb 2012
Page 9 of 9
______________________________________________________________________________________________________________________

SECTION 16

OTHER INFORMATION

KEY TO ABBREVIATIONS AND ACRONYMS:

N/D = Not determined, N/A = Not applicable, STEL = Short-Term Exposure Limit, TWA = Time-Weighted Average

THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS:

Revision Changes:
Company Logo (Fld 1) was modified.
Section 01: Product Code was modified.
Section 09: Phys/Chem Properties Note was modified.
Section 09: Boiling Point C(F) was modified.
Section 08: Comply with applicable regulations phrase was modified.
Section 09: Vapour Pressure was modified.
Section 09: Relative Density - Header was modified.
Section 09: Flash Point C(F) was modified.
Section 09: Viscosity was modified.
Section 09: Viscosity was modified.
Section 15: National Chemical Inventory Listing was modified.
Section 15: Australian Poison Schedule Allocated was modified.

----------------------------------------------------------------------------------------------------------------------------------------------------The information and recommendations contained herein are, to the best of ExxonMobil's knowledge and belief,
accurate and reliable as of the date issued. You can contact ExxonMobil to insure that this document is the most
current available from ExxonMobil. The information and recommendations are offered for the user's consideration and
examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer
repackages this product, it is the user's responsibility to insure proper health, safety and other necessary information is
included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to
handlers and users. Alteration of this document is strictly prohibited. Except to the extent required by law, republication or retransmission of this document, in whole or in part, is not permitted. The term, "ExxonMobil" is used for
convenience, and may include any one or more of ExxonMobil Chemical Company, Exxon Mobil Corporation, or any
affiliates in which they directly of indirectly hold any interest.
----------------------------------------------------------------------------------------------------------------------------------------------------DGN: 7084272DAU (1013763)
----------------------------------------------------------------------------------------------------------------------------------------------------Prepared by:
Exxon Mobil Corporation
EMBSI, Clinton NJ USA
Contact Point:
See Section 1 for Local Contact number

End of (M)SDS