OSHA Training Institute

Introduction to OSHA
INSTRUCTOR GUIDE

OSHA Directorate of Training and Education

December 2013

Introduction to OSHA
2 HOUR LESSON

Table of Contents
TRAINER PREPARATION GUIDANCE ........................................................................................................ i
Lesson Overview ....................................................................................................................................... 1
Topic 1: Why is OSHA important to you? ................................................................................................. 2
A. History of OSHA .......................................................................................................................... 3
B. OSHAs mission ........................................................................................................................... 5
C. Importance of this training ........................................................................................................... 6
Topic 2. What rights do you have under OSHA? ...................................................................................... 7
A. Right to a safe & healthful workplace .......................................................................................... 8
B. Right to know about hazardous chemicals .................................................................................. 9
C. Right to information about injuries and illnesses in your workplace .......................................... 10
D. Right to complain or request hazard correction from your employer ........................................ 10
E. Right to training.......................................................................................................................... 11
F. Right to hazardous exposure records and medical records ...................................................... 11
G. Right to file a complaint with OSHA .......................................................................................... 12
H. Right to participate in an OSHA inspection ............................................................................... 12
I. Right to be free from retaliation for exercising safety and health rights ...................................... 13
J. Worker responsibilities ............................................................................................................... 13
Topic 3. What responsibilities does your employer have under OSHA? ................................................ 15
A. Provide a workplace free from recognized hazards & comply with OSHA standards ............... 15
B. Provide training required by OSHA standards .......................................................................... 16
C. Keep records of injuries and illnesses ....................................................................................... 19
D. Provide medical exams and access to exposure and medical records .................................... 21
E. Not discriminate against workers who exercise their rights....................................................... 21
F. Post OSHA citations and abatement verification notices .......................................................... 22
G. Provide and pay for PPE ........................................................................................................... 22
Topic 4. What do the OSHA standards say? .......................................................................................... 24
A. Types of standards .................................................................................................................... 24
B. How the standards are organized.............................................................................................. 25
Topic 5. How are OSHA inspections conducted? ................................................................................... 27
A. Inspection priorities .................................................................................................................... 27
B. Stages of an inspection ............................................................................................................. 29
C. Citations and penalties .............................................................................................................. 31
D. Appeals process ........................................................................................................................ 33
Topic 6. Where can you go for help? ...................................................................................................... 35
A. Sources within the workplace/worksite ...................................................................................... 35
B. Sources outside the workplace/worksite ................................................................................... 37
C. How to file an OSHA complaint ................................................................................................. 39
Session Summary ................................................................................................................................... 42
Conduct Test Answer Key.................................................................................................................... 43
References: ............................................................................................................................................. 44

APPENDIX A: SDS Explanation .................................................................................................................A1

APPENDIX B: Handout #12a, #12b, #12c Answer Sheet ..........................................................................B1
APPENDIX C: Check Yourself Test Questions Answer Sheet .................................................................. C1
APPENDIX D: Check Yourself Test Questions Student Copy................................................................... D1
12.2013

Introduction to OSHA
2 HOUR LESSON

12.2013

Introduction to OSHA
2 HOUR LESSON

TRAINER PREPARATION GUIDANCE

The Introduction to OSHA lesson of the Outreach Training Program includes an instructor guide for the
trainer, a slide presentation, and student handouts. This lesson is for General Industry, Construction
and/or Maritime Industry training.
Using the Instructor Guide (IG): The IG consists of instructions for trainer preparation, a detailed lesson
plan, instructor references for student Handouts #3 and #12a, #12b, and #12c, along with test questions
and answers. The IG contains detailed content, activities, references and notes for the trainer. It is not
intended to be a script that is read verbatim to the students. Rather, trainers should review the
entire guide (including referenced materials and internet links) prior to conducting training, and
use it as a resource in their planning and presentation. The instructor presentation and preparation
materials not included in this package may be downloaded from the OSHA website at
http://www.osha.gov. The OSHA standards may also be purchased from the Government Printing Office
(GPO) Bookstore at http://bookstore.gpo.gov.
The learning objectives: The Introduction to OSHA lesson was developed based on the terminal (TO)
and enabling objectives (EO) below. These objectives are the expected student outcomes; therefore, the
trainer may not vary from these objectives when planning the training session.

TO: Given OSHA historical events and current information, the student will be able to explain the
importance of OSHA in providing a safe and healthful workplace to workers covered by OSHA.
Specifically, the student will be able to:
EO 1: Explain why OSHA is important to workers
EO 2: Explain worker rights under OSHA
EO 3: Discuss employer responsibilities under OSHA
EO 4: Discuss the use of OSHA standards
EO 5: Explain how OSHA inspections are conducted
EO 6: Utilize helpful worker safety and health resources
TM

Using the Slide Presentation: The Microsoft PowerPoint 2010 file consists of 48 slides, which may be
used by the trainer as a visual aid during the session. However, the focus of the training should be on
TM
discussion and interaction with the students, not on the PowerPoint slides. The presentation was
TM
developed using Microsoft PowerPoint 2010; therefore, it is compatible with this and higher versions of
the product.
Using the Student Handout Packet: The packet contains 12 numbered handouts representing 16 files
in the packet, since there are 3 versions (one for General Industry, one for Construction and one for
Maritime) of 2 of the handouts (Handout #8, How to Read the OSHA Standards and Handout #12, Filing
an OSHA Complaint). Along with your copy, copies of the Student Handout Packet should be made for
each student.
An overview of the handouts and their use are tabled below. Step-by-step instructions are contained in
the IG in the Detailed Content and Notes sections of the lesson.
Handout
#1. Weekly Fatality/Catastrophe
Report
#2. OSHA Poster
#3. SDS Example

12.2013

Use
Topic 1: Use during the Fatality/Catastrophe Small Group
Activity. You may also download a Fatality/Catastrophe list of
weekly reports from the OSHA website.
Topic 2: Discuss the worker rights included on the poster, as well
as additional worker rights.
Topic 2: Conduct a group discussion on SDSs and chemicals
used in the workplace. Appendix A, SDS Explanation, may be
Page i

Introduction to OSHA
2 HOUR LESSON

Handout
#4. Your Rights as a Whistleblower
Fact Sheet
#5. Refusing to Work Because
Conditions are Dangerous

#6. OSHA 300 Log example

#7. Employers Must Provide and
Pay for PPE
#8. How to Read the OSHA
Standards: a. General Industry;
b. Construction;
c. Maritime Industry
#9. Safety and Health Resources
#10. Navigating the OSHA
Website
#11. Identifying Safety and Health
Problems in the Workplace
#12. Filing an OSHA Complaint
includes tips for completion,
scenario and form:
a. General Industry*;
b. Construction*;
c. Maritime Industry*

Use
used for instructor reference.
Topic 2: Highlight when covering the worker right to be free from
retaliation for exercising safety and health rights.
Topic 2: Refer to when covering the worker right to refuse to do a
job if the worker believes in good faith that they are exposed to
an imminent danger.

Topic 3: Use when conducting the OSHA-300 Log Classroom

Exercise.
Topic 3: Discuss when covering the employer requirement to
provide and pay for PPE.
Topic 4: Use when conducting the OSHA Standards Classroom
Exercise. Select the version (a, b or c) which is appropriate for
your audience.
Topic 6: Refer to when discussing safety and health resources
outside the workplace/worksite.
Topic 6: Discuss when covering the OSHA website.
Topic 6: Refer to when discussing filing a complaint to get
workplace hazards corrected.
Topic 6: Highlight when conducting the Filing an OSHA
Complaint Small Group Activity. Select the version (a, b or c)
which is appropriate for your audience. Appendix B, Handout
#12a, #12b, #12c Answer Sheet, may be used for instructor
reference.

*You may develop an alternate scenario for the activity covering filing a complaint (Handout #12a, #12b,
or #12c). If so, the following information should be included:
Company name, address and telephone number (and site information, if a different location)
Management official in charge
Type of business
Description of the hazard or hazards, including location and number of workers exposed
Whether the hazard has been brought to the attention of management or other government
agency
For the alternate scenario, you can use a situation with which you are familiar, or you can access OSHA
accident summaries for scenario ideas at: www.osha.gov/pls/imis/accidentsearch.html
Media and/or Teaching Methods
The Introduction to OSHA 2-hour session has been set up as a facilitated, interactive training session.
Students are given small chunks of information, and then are able to test their understanding of the
subject matter via activities and workshops. Several practice sessions included are designed to increase
student awareness and enable them to apply what they have learned when they return to their
workplaces.
Ideal Setting or Conditions for the Training Session
The ideal setting for this course is a classroom or other area where students have space to break into
groups.
Disclaimer
This material is intended for training purposes only. Its purpose is to provide basic information about
OSHA to workers and to inform workers of their rights under OSHA. This material is not a substitute for
any provision of the Occupational Safety and Health Administration or any standards issued by OSHA.
12.2013

Page ii

Introduction to OSHA
2 HOUR LESSON

12.2013

Page iii

Introduction to OSHA
2 HOUR LESSON

Lesson Overview
The purpose of this two-hour lesson is to provide workers with introductory
information about OSHA. This Instructor Guide is intended to be used when
presenting General Industry, Construction, and/or Maritime Industry outreach
courses. The lesson is comprised of the following six topics:
1. Why is OSHA important to you?
2. What rights do you have under OSHA?
3. What responsibilities does your employer have under OSHA?
4. What do the OSHA standards say?
5. How are OSHA inspections conducted?
6. Where can you go for help?
The lesson provides basic knowledge of: OSHAs history and mission, worker rights
under OSHA, employer responsibilities under OSHA, OSHA standards, OSHA
inspections, and safety and health resources, including how to file an OSHA complaint.

Materials
Needed:

Listed in
presentation order
Flip chart and
markers
Presentation
slides
Student handout
package
OSH Act
Copy of the OSHA
Standards,
General Industry,
Construction, or
Maritime
Check Yourself
Test Questions

12.2013

Training
Preparation:

All About OSHA

publication
Complaint scenario
[Handouts #12a, #12b,
and #12c] answers
Cornell University
Library site on the
Triangle Fire:
http://www.ilr.cornell.e
du/trianglefire/
SDS explanation
NIOSH website:
http://cdc.gov/niosh
OSHA website:
http://www.osha.gov
State Job Safety and
Health Programs Fact
Sheet
Training Requirements
in OSHA Standards
and Training
Guidelines publication

Student
Handout Packet:

#1. Weekly Fatality/Catastrophe

Report
#2. OSHA Poster
#3. SDS Example
#4. Your Rights as a
Whistleblower Fact Sheet
#5. Refusing to Work Because
Conditions are Dangerous
#6. OSHA 300 Log example
#7. Employers Must Provide and
Pay for PPE
#8. How to Read the OSHA
Standards: a. General
Industry; b. Construction; c.
Maritime Industry
#9. Safety and Health Resources
#10. Navigating the OSHA Website
#11. Identifying Safety and Health
Problems in the Workplace
#12. Filing an OSHA Complaint
includes tips for completion,
scenario and form: a. General
Industry; b. Construction, c.
Maritime Industry
Page 1

Introduction to OSHA
2 HOUR LESSON

Topic 1: Why is OSHA important to you?

NOTES:

A. History of OSHA
B. OSHAs mission
C. Importance of this training

Instruction for Topic 1:

1. Ask the class Questions to Ask and discuss.
2. Conduct Small Group Activity: Weekly
Fatality/Catastrophe Report as an introduction
to the training session. See page 2 (below).
3. Discuss Detailed Content section.
4. Conduct the Classroom Exercise OSHA
Coverage. See page 5.
5. Have the class answer the Questions for
Review.
Questions to Ask:
When, during your work experience, did you
first hear about OSHA?
What did you think about OSHA then?
What do you think OSHAs job is?
Small Group Activity
Fatality/Catastrophe (FAT/CAT) Report
Have the class break up into groups of 3-5 people.
1. Refer students to the Weekly
Fatality/Catastrophe Report and explain its
purpose. (Emphasize that this represents one
week of worker fatalities reported to OSHA.)
Show where the current report is located on the
website, if available.
2. Tell the class to look at the list and see if they
know or have heard of any similar incidents or
near misses. Allow a minute or so for the class
to scan the report.
3. Ask each group to discuss an incident from the
report, or a similar incident that they know of or
have heard about on their job.
4. After a few minutes, bring class back together.
5. Ask for a few volunteers to share an experience
they may have heard of, what they discussed in
their group, and how an incident was or may
have been prevented.

12.2013

Refer to Handout #1: Weekly

Fatality/Catastrophe Report and/or
Fatality/Catastrophe list of weekly
reports online at:
http://www.osha.gov/dep/fatcat/de
p_fatcat.html

Sum up the exercise by stating

that hazard prevention is OSHAs
priority. If workers know their
rights, and employers meet their
responsibilities, lives and limbs can
be saved. Focus on how important
this training is to the participants.
Page 2

Introduction to OSHA
2 HOUR LESSON

Detailed Content for Topic 1:

A. History of OSHA
OSHA stands for the Occupational Safety and Health
Administration, an agency of the U.S. Department of
Labor. OSHAs responsibility is worker safety and
health protection. The U.S. Congress created OSHA
under the Occupational Safety and Health Act of 1970
(the OSH Act). Congress passed the law and
established OSHA to assure so far as possible every
working man and woman in the nation safe and
healthful working conditions and to preserve our
human resources.

NOTES:

OSHA began because, until 1970, there were no

national laws for safety and health hazards.
Some events that led to the OSHA law include:
The 1911 Triangle Shirtwaist Company fire in New
York City killed 146 of 500 employees in one of
the worst work-related disasters in our countrys
history. Factory workers, mainly young, female
immigrants working long hours for low wages,
died because doors were locked and there were
no fire escapes. This tragedy outraged the public,
who called for safety and health reform. Frances
Perkins, who later became the first Secretary of
Labor, investigated the Triangle fire and tried to
find ways to prevent future occurrences.
Production for World War I caused a crisis in
workplace safety and health conditions. The
government created a Working Conditions Service
to help states inspect plants and reduce hazards.
In the 1930s, as part of President Roosevelts
New Deal, additional laws increased the federal
governments role in job safety and health. But the
federal role was mainly to provide service and
information to state governments. By the late
1950s, the Federal-State partnership could no
longer deal with the growing workforce and
increasing hazards. Additional federal laws were
enacted, but only covered certain industries.
12.2013

If Internet access is available, and

time permits, briefly explore the
Cornell University Library web
exhibit on the Triangle Fire
(http://www.ilr.cornell.edu/trianglefi
re/ about.html) with the class.
There are also videos about the
fire on YouTube.com

Page 3

Introduction to OSHA
2 HOUR LESSON

By the 1960s, 14,000 workers died every year

and more than 2.2 million workers were not able
to work from injuries and illnesses.

NOTES:

Many thought that the only solution was a Federal law

with the same rules and enforcement for everyone.
On December 29, 1970, President Nixon signed the
OSH Act. This Act created OSHA, the agency, which
formally came into being on April 28, 1971. With the
creation of OSHA, for the first time, all employers in
the United States had the legal responsibility to
provide a safe and healthful workplace for employees.
And, there were now uniform regulations that applied
to all workplaces.

Ask the class if anyone

has seen the OSH Act.
Tell them that they can
find it on OSHAs website. Show
them the website, if internet
access is available, or have a hard
copy of the Act to show them.

The OSH Act is also known as Public Law 91-596. It

covers all private sector employers and their workers
in the 50 states and all territories and jurisdictions
under federal authority. Employers and workers in
many fields, including but not limited to
manufacturing, construction, longshoring, agriculture,
law, medicine, charity and disaster relief are covered
by OSHA. Religious groups are covered if they
employ workers for secular purposes, such as
maintenance or gardening.

The OSH Act covers Federal

workers by conducting inspections
in response to complaints, but
OSHA cannot propose monetary
fines against federal agencies.

Which groups do not come under OSHAs coverage?

The self-employed;
Immediate members of farming families not
employing outside workers;
Mine workers, certain truckers and transportation
workers, and atomic energy workers who are
covered by other federal agencies;
Public employees in state and local governments,
although some states have their own plans that
cover these workers.

12.2013

Page 4

Introduction to OSHA
2 HOUR LESSON

Classroom Exercise
OSHA Coverage
Covered by
OSHA?

Worker

YES

NO

1. Harry Adams, a miner at Below Ground

Inc.

YES

NO

YES

NO

YES

NO

2. Adrian Smith, one of 3 employees of

ABC landscaping.
3. Taylor Dell, an accountant in business for
herself.

NOTES:
Ask the class the
questions on coverage
and discuss the
responses.
Answers:
1. No, miners are covered by
MSHA;
2. Yes.
3. No, the self-employed are not
covered.
4. Yes.

4. Rob Jones, one of 10 carpenters working

for Woody, Inc.

B. OSHAs mission
Now that you know a little bit about why OSHA was
created, lets talk about OSHAs mission. The mission
of OSHA is to save lives, prevent injuries and protect
the health of Americas workers.
To achieve this, federal and state governments work
together with more than 100 million working men and
women and eight million employers. Some of the
things OSHA does to carry out its mission are:
developing job safety and health standards and
enforcing them through worksite inspections,
maintaining a reporting and recordkeeping system
to keep track of job-related injuries and illnesses,
and
providing training programs to increase knowledge
about occupational safety and health.
OSHA also assists the States in their efforts to assure
safe and healthful working conditions, through OSHAapproved job safety and health programs operated by
individual states. State plans are OSHA-approved job
safety and health programs operated by individual
states instead of federal OSHA. States with approved
plans cover most private sector employees as well as
state and local government workers in the state. State
plan programs respond to accidents and employee
complaints and conduct unannounced inspections,
just like federal OSHA. And, some states have
OSHA-approved plans that cover only state and local
government workers.

12.2013

Refer to the OSHA website for

additional information on State
Programs and a State Plan
directory.
If you are conducting training in a
location with state jurisdiction,
discuss the Federal/State
relationship in more detail. Refer to
the State Job Safety & Health
Programs Fact Sheet for additional
information.

Page 5

Introduction to OSHA
2 HOUR LESSON

C. Importance of this training

Even though OSHA has had an impact on worker
safety and health, significant hazards and unsafe
conditions still exist in U.S. workplaces.
Each year:
On average, 15 workers die every day from job
injuries
Over 5,600 Americans die from workplace injuries
annually
Over 4 million non-fatal workplace injuries and
illnesses were reported; and
The estimated cost of occupational injuries and
illnesses are from $145 billion to $290 billion a year for
direct and indirect costs

NOTES:
During discussion of OSHAs
impact and what remains to be
done, re-emphasize the fatalities
reported to OSHA in a one week
timeframe from the Small Group
Activity conducted earlier.
Figures are from the AFL-CIO
Report, Death on the Job: The Toll
of Neglect, April, 2009. According
to the report, these estimates are
based upon only injuries that are
disabling and that are reported by
employers, and understate the full
extent of occupational injuries and
illnesses and their associated
costs.

OSHA is a small agency, with approximately 1000

federal inspectors and 1400 state inspectors to cover
about eight million workplaces. As you can see from
these numbers, OSHA cannot be everywhere. That is
why it is important for you to know your rights and for
employers to be aware of their responsibilities under
OSHA. This training will help you know whether your
employer is complying with OSHA standards, what
rights you have related to job safety and health, and
where you can go if you need help.
When you know your rights, and when employers act
responsibly to prevent hazards, the result will be fewer
worker deaths, injuries and illnesses. Training and
education are key in making this happen.
Answers:

Questions for Review

1. Why was OSHA necessary?
2. What is OSHAs mission?
3. Why is this training important?

12.2013

1. Workplace injuries, illnesses

and death were increasing and
no uniform or comprehensive
law existed to protect against
workplace hazards.
2. To save lives, prevent injuries
and protect the health of
Americas workers.
3. Youll know your rights, if there
are hazards in your workplace,
and where to get help.
Page 6

Introduction to OSHA
2 HOUR LESSON

Topic 2. What rights do you have under OSHA?

A. Right to a safe and healthful workplace
B. Right to know about hazardous chemicals
C. Right to information about injuries and illnesses
in your workplace
D. Right to complain or request hazard correction
from employer
E. Right to training
F. Right to hazard exposure and medical records
G. Right to file a complaint with OSHA
H. Right to participate in an OSHA inspection
I. Right to be free from retaliation for exercising
safety and health rights
J. Worker responsibilities
Instruction for Topic 2:
1. Refer to the OSHA Poster and discuss the
worker rights included. Note that there are
additional rights that will be discussed in this
session.
2. Discuss Detailed Content section.
3. Conduct Classroom Exercise on the Safety
Data Sheet (SDS). See page 9.
4. Have the class answer the Questions for
Review.

NOTES:

Refer to Handout #2: Copy of

OSHA Poster

Detailed Content for Topic 2

The Occupational Safety and Health Act of 1970 gave
workers many new rights related to safety and health.
OSHA standards which have been issued since then,
such as the Hazard Communication or Right to Know
standard, provide additional rights.

12.2013

Page 7

Introduction to OSHA
2 HOUR LESSON

A. Right to a safe & healthful workplace

Most importantly, the creation of OSHA provided
workers the right to a safe and healthful workplace.
Section 5(a)(1) of the OSH Act states: Each employer
shall furnish to each of his employees employment
and a place of employment which are free from
recognized hazards that are causing or are likely to
cause death or serious physical harm to his
employees." A safe and healthful workplace means
that hazards are removed and workers are trained. If a
hazard cannot be removed completely, protection (for
example, respirators or earplugs) must be provided.
Some examples of a safe/healthful workplace include:
Fall protection and training are provided and
required when working at high levels on a
construction site.
Machines and equipment with rotating and
moving parts are guarded.

NOTES:
Ask the class if they have
seen the OSHA poster in
their workplace. If so, ask
where it is posted.
Tell the class that all employers
covered by the OSHA Act must
display the OSHA poster.
(Employers in states operating
OSHA-approved state plans
should obtain and post the states
equivalent poster.)

Ask the class to provide

examples of how a safe
and healthful workplace is
provided [or should be provided] at
their workplace or worksite.

If not discussed, provide additional examples, such as:

Trenches are inspected and have protective
systems in place.
Proper confined space entry procedures,
testing, equipment, and training are present.
Noise levels are controlled. When levels are still
high, workers are given hearing tests and are
provided training and hearing protection.
Protection from chemical hazards is provided,
including an evaluation of chemicals used, a
written program, Safety Data Sheets, worker
protection (for example, respirators or gloves),
and information and training.

12.2013

Page 8

Introduction to OSHA
2 HOUR LESSON

NOTES:
B. Right to know about hazardous chemicals
Another important right is the Right to Know about
hazardous substances in your workplace. Employers
must have a written, complete hazard communication
program that includes information on:
Container labeling,
Safety Data Sheets (SDSs), and
Worker training. The training must include the
physical and health hazards of the chemicals
and how workers can protect themselves;
including specific procedures the employer has
implemented to protect workers, such as work
practices, emergency procedures, and personal
protective equipment.

The program must also include a list of the hazardous

chemicals in each work area and the means the
employer uses to inform workers of the hazards of
non-routine tasks. In addition, the program must
explain how the employer will inform other employers
of hazards to which their workers may be exposed (for
example, contract workers).
Classroom Exercise
SDS
1. Refer to the SDS example and, using the SDS
explanation for reference, have a brief group
discussion on SDSs and chemicals. Some
questions to start the discussion include:
a. What information does the SDS provide?
b. Has anyone seen an SDS in their
workplace?
c. Were the instructions on the SDS
followed in their workplace?
d. Has anyone worked with hazardous
substances without an SDS?

Refer to Handout #3: SDS

Example for student. Use
Appendix A: SDS Explanation if
needed.
NOTE: Safety Data Sheet The
Hazard Communication Standard
(HCS) requires chemical
manufacturers, distributors, or
importers to provide Safety Data
Sheets (SDSs) (formerly known as
Material Safety Data Sheets or
MSDSs) to communicate the
hazards of hazardous chemical
products. As of June 1, 2015, the
HCS will require new SDSs to be
in a uniform format.
Sum up the exercise by
emphasizing that the SDS
provides important information to
workers about hazardous
chemicals in the workplace.

12.2013

Page 9

Introduction to OSHA
2 HOUR LESSON

C. Right to information about injuries and

illnesses in your workplace
OSHAs Recordkeeping rule requires most employers
with more than 10 workers to keep a log of injuries
and illnesses. The log, which is also called the OSHA
300, must contain all work-related injuries and
illnesses resulting in lost workdays, restricted work or
transfer to another job, as well as any incident
requiring more than first aid treatment.
You have the right to review the current log, as well as
the logs stored for the past 5 years. The employer
must provide this by the end of the next workday. The
names and other information on the log may not be
removed, unless the case is a privacy concern case.

NOTES:
Ask the class if their
employer has set up a way
for them to report injuries
and illnesses.
The right to review the log includes
former employees, their personal
representatives, and authorized
employee representatives.
Privacy concern cases are those
involving an intimate body part,
mental illness, HIV, etc. For more
detail, see 1904.29(b)(7).

You also have the right to view the annually posted

summary of the injuries and illnesses (OSHA 300A).
D. Right to complain or request hazard correction
from your employer
Workers may bring up safety and health concerns in
the workplace to their employers without fear of
discharge or discrimination, as long as the complaint
is made in good faith. OSHA regulations [29CFR
1977.9(c)] protect workers who complain to their
employer about unsafe or unhealthful conditions in the
workplace. You cannot be transferred, denied a raise,
have your hours reduced, be fired, or punished in any
other way because you have exercised any right
afforded to you under the OSH Act.

Ask the class if they have

ever reported a hazard to
their supervisor. If so,
what was the outcome?
1977.9(c) states: the principles of
the Act would be seriously
undermined if employees were
discouraged from lodging
complaints about occupational
safety and health matters with their
employers. Such complaints to
employers, if made in good faith,
therefore would be related to the
Act, and an employee would be
protected against discharge or
discrimination caused by a
complaint to the employer.

Since you are often closest to potential safety and

health hazards, you have a vested interest in reporting
problems so that the employer gets them fixed. If the
hazard is not getting corrected, you should then
contact OSHA.

12.2013

Page 10

Introduction to OSHA
2 HOUR LESSON

E. Right to training
You have a right to get training from your employer on
a variety of health and safety hazards and standards
that your employer must follow. Were already
discussed the training required under OSHAs Hazard
Communication (Right to Know) standard. Other
required training includes lockout-tagout, bloodborne
pathogens, noise, confined spaces, fall hazards in
construction, personal protective equipment, and a
variety of other subjects.
F. Right to hazardous exposure records and
medical records
Under OSHAs standard 1910.1020, you have the
right to examine and copy exposure and medical
records, including records of workplace monitoring or
measuring a toxic substance. This is important if you
have been exposed to toxic substances or harmful
physical agents in the workplace, as this regulation
may help you detect, prevent, and treat occupational
disease.

NOTES:

Access means the right to examine

and copy medical and exposure
records.

Examples of toxic substances and harmful physical

agents are:

Metals and dusts, such as, lead, cadmium, and

silica.
Biological agents, such as bacteria, viruses,
and fungi.
Physical stress, such as noise, heat, cold,
vibration, repetitive motion, and ionizing and
non-ionizing radiation.

OSHA standards require employers to measure

exposure to harmful substances, and workers or their
representatives have the right to observe the testing
and examine the results. If the exposure levels are
above the limit set by the standard, the employer must
tell workers what will be done to reduce their
exposure.

12.2013

Page 11

Introduction to OSHA
2 HOUR LESSON

G. Right to file a complaint with OSHA

You may file a complaint with OSHA if you believe a
violation of a safety or health standard, or an imminent
danger situation, exists in your workplace. You may
request that your name not be revealed to your
employer. You can file a complaint on OSHAs web
site, in writing or by telephone to the nearest OSHA
area office. You may also call the office and speak
with an OSHA compliance officer about a hazard,
violation, or the process for filing a complaint.

NOTES:
Filing a complaint is covered later
in this session.

If you file a complaint, you have the right to find out

OSHAs action on the complaint and request a review
if an inspection is not made.
H. Right to participate in an OSHA inspection
If an OSHA inspection is conducted in your workplace,
you have the right to have your representative
accompany the inspector on the inspection. You also
have the right to talk to the inspector privately. You
may point out hazards, describe injuries, illnesses or
near misses that resulted from those hazards and
describe any concern you have about a safety or
health issue. You also have the right to find out about
inspection results and abatement measures, and get
involved in any meetings or hearings related to the
inspection. You may also object to the date set for the
violation to be corrected and be notified if the
employer files a contest.

12.2013

CONTEST: If an employer
disagrees with the results of the
OSHA inspection, he or she may
submit a written objection to
OSHA, called a Notice of Contest.

Page 12

Introduction to OSHA
2 HOUR LESSON

I. Right to be free from retaliation for exercising

safety and health rights
Workers have a right to seek safety and health on the
job without fear of punishment. That right is spelled
out in Section 11(c) of the OSH Act. The law says the
employer shall not punish or discriminate against
employees for exercising such rights as complaining
to the employer, union, OSHA, or any other
government agency about job safety and health
hazards. Workers are also protected for participation
in OSHA inspections, conferences, hearings, and
other OSHA-related activities. Workers also have the
right to refuse to do a job if they believe in good faith
that they are exposed to an imminent danger. "Good
faith" means that even if an imminent danger is not
found to exist, the worker had reasonable grounds to
believe that it did exist. Since the conditions necessary
to justify a work refusal are very stringent, refusing
work should be an action taken as a last resort. If time
permits, the condition should be reported to OSHA or
the appropriate government agency.

NOTES:
Refer to Handout #4: Your Rights
as a Whistleblower Fact Sheet

Refer to Handout #5: Refusing to

Work because Conditions are
Dangerous

If you believe you have been punished for exercising

your safety and health rights, you must contact OSHA
within 30 days.
J. Worker responsibilities
OSHA holds employers responsible for the safety and
health conditions in the workplace and does not cite
workers for violations. However, Section 5(b) of the
OSHA Act states that each employee shall comply
with occupational safety and health standards and all
applicable rules, regulations and orders.
Workers are encouraged to follow all appropriate
safety and health rules, and wear protective
equipment while working.

12.2013

Page 13

Introduction to OSHA
2 HOUR LESSON

Questions for Review

1. What does an SDS tell you?
2. What are some worker rights related to injury
and illness reporting?
3. Name some standards or hazards where
workers must be trained.

12.2013

Answers:
1. Chemical name, hazardous
ingredients, physical and
chemical characteristics, fire
and explosion hazards,
compatibility and reactivity,
health hazards, precautions
for safe use and handling,
and control measures.
2. Know how to report
injuries/illnesses, see the
annual summary, and review
the log.
3. Lockout/Tagout, fall hazards
in construction, hazard
communication, confined
spaces, bloodborne
pathogens, and personal
protective equipment.

Page 14

Introduction to OSHA
2 HOUR LESSON

Topic 3. What responsibilities does your employer

have under OSHA?
A. Provide a workplace free from recognized
hazards and comply with OSHA standards
B. Provide training required by OSHA standards
C. Keep records of injuries and illnesses
Set up a reporting system
Provide copies of logs, upon request
Post the annual summary
Report within 8 hours any accident resulting
in a fatality or the hospitalization of 3 or
more workers
D. Provide medical exams when required by
OSHA standards and provide workers access
to their exposure and medical records
E. Not discriminate against workers who exercise
their rights under the Act (Section 11(c))
F. Post OSHA citations and abatement verification
notices
G. Provide and pay for PPE

NOTES:

Instruction for Topic 3:

1. Discuss Detailed Content section.
2. Ask the class about safety and health training
they have received on the job.
3. Conduct the Classroom Exercise on the OSHA
300 Log. See page 20.
4. Have the class answer the Questions for
Review.
DETAILED CONTENT for Topic 3:
A. Provide a workplace free from recognized
hazards and comply with OSHA standards
Establishing a safe and healthful workplace requires
every employer to make safety and health a priority. In
general, OSHA requires employers to:

12.2013

Page 15

Introduction to OSHA
2 HOUR LESSON

Maintain conditions and adopt practices

reasonably necessary to protect workers on the
job. The first and best strategy is to control the
hazard at its source. Engineering controls do this,
unlike other controls that generally focus on the
worker who is exposed to the hazard. The basic
concept behind engineering controls is that, to the
extent feasible, the work environment and the job
itself should be designed to eliminate hazards or
reduce exposure to hazards.
Be familiar with the standards that apply to their
workplaces, and comply with these standards.
Ensure that workers are provided with, and use,
personal protective equipment, when needed.
[When exposure to hazards cannot be engineered
completely out of normal operations or
maintenance work, and when safe work practices
and other forms of administrative controls cannot
provide sufficient additional protection, an
additional method of control is the use of protective
clothing or equipment. This is collectively called
personal protective equipment, or PPE. PPE may
also be appropriate for controlling hazards while
engineering and work practice controls are being
installed.], and
Comply with the OSH Acts General Duty Clause
where no specific standards apply. [The general
duty clause, or Section 5(a)(1) of the Act requires
each employer to furnish a place of employment
which is free from recognized hazards that are
causing or are likely to cause death or serious
physical harm to employees.]

B. Provide training required by OSHA standards

We already discussed your right to receive training
from your employer on a variety of health and safety
hazards and standards, such as chemical right to
know, fall protection, confined spaces and personal
protective equipment.

12.2013

NOTES:

See the publication, Training

Requirements in OSHA Standards
and Training Guidelines for
additional information.

Page 16

Introduction to OSHA
2 HOUR LESSON

Many OSHA standards specifically require the

employer to train workers in the safety and health
aspects of their jobs. Other OSHA standards make it
the employers responsibility to limit certain job
assignments to those who are certified, competent,
or qualifiedmeaning that they have had special
previous training, in or out of the workplace.
OSHA believes that training is an essential part of
protecting workers from injuries and illnesses.

NOTES:

OSHA construction standards include a general

training requirement, which states:

See 1926.21(b)

Ask the class about safety

and health training they
have received prior to this
course.

The employer shall instruct each employee in the

recognition and avoidance of unsafe conditions and
the regulations applicable to his work environment to
control or eliminate any hazards or other exposure to
illness or injury.
Additional general training requirements for
construction include training for workers:

required to handle or use poisons, caustics, and

other harmful substances;
who may be exposed to job sites where harmful
plants or animals are present;
required to handle or use flammable liquids,
gases, or toxic materials; or
required to enter into confined or enclosed
spaces.

There are also more specific training requirements,

particularly in standards put into effect since 1990. For
example, OSHAs scaffold standard and fall protection
standard each has a separate section on training
requirements that is intended to clarify the general
training requirements in 1926.21(b)(2).

12.2013

See 1926.454(a) and 1926.503(a)

OSHA construction standards for
scaffolds and fall protection.

Page 17

Introduction to OSHA
2 HOUR LESSON

The scaffold requirement says that employers shall

have each employee who performs work while on a
scaffold trained by a person qualified in the subject
matter to recognize the hazards associated with the
type of scaffold being used and to understand the
procedures to control or minimize those hazards. It
goes into detail about what the training must cover.
The fall protection standard has similar requirements.

NOTES:

OSHAs Hazard Communication standard applies to

both General Industry and Construction workers and
requires that employers provide workers with effective
information and training on hazardous chemicals in
their work area at the time of their initial assignment,
and whenever a new physical or health hazard is
introduced. In addition, as we discussed earlier,
chemical-specific information must always be
available through labels and safety data sheets
(SDSs).

See 1910.1200(h), OSHA standard

for Hazard Communication
information and training.

OSHA requires the use of personal protective

equipment (PPE) to reduce employee exposure to
hazards when engineering and administrative controls
are not feasible or effective in reducing these
exposures to acceptable levels. Employers are
required to determine if PPE should be used to protect
their workers.
If PPE is to be used, a PPE program should be
implemented. This program should address the
hazards present; the selection, maintenance, and use
of PPE; the training of employees; and monitoring of
the program to ensure its ongoing effectiveness.
1910.132(f) (which applies to General Industry
workplaces) contains detailed training requirements
for workers who must wear or use PPE.

12.2013

Page 18

Introduction to OSHA
2 HOUR LESSON

C. Keep records of injuries and illnesses

Including:
Set up a reporting system
Provide copies of logs, upon request
Post the annual summary
Report within 8 hours any accident resulting in
a fatality or the hospitalization of 3 or more
workers
Recordkeeping is an important part of an employers
responsibilities. Keeping records allows OSHA to
collect survey material, helps OSHA identify highhazard industries, and informs you, the worker, about
the injuries and illnesses in your workplace. About 1.5
million employers with 11 or more employees-20
percent of the establishments OSHA covers-must
keep records of work-related injuries and illnesses.
Workplaces in low-hazard industries such as retail,
service, finance, insurance, and real estate are
exempt from recordkeeping requirements.

NOTES:

Employers exempt from

recordkeeping requirements must
still report deaths and the
hospitalization of 3 or more to
OSHA.

Reporting and Recording Checklist

Employers must:
Report each worker death
Report each incident that hospitalizes 3 or more
workers
Maintain injury & illness records
Inform workers how to report an injury or illness to
the employer
Make records available to workers
Allow OSHA access to records
Post annual summary of injuries & illnesses

For specific information on exactly which cases must

be recorded, you can go to Title 29 of the Code of
Federal Regulations (CFR) Part 1904Recording and
Reporting Occupational Injuries and Illnesses. The
forms your employer must keep are:
The Log of Work-Related Injuries and Illnesses
(commonly called the OSHA 300 Log) is used
to list injuries and illnesses and track days
away from work, restricted, or transferred.

12.2013

Page 19

Introduction to OSHA
2 HOUR LESSON

The Injury and Illness Report (Form 301) is

used to record more information about each
case. Employers can use a workers
compensation or insurance form, if it contains
the same information.
The Summary (OSHA Form 300A) shows the
totals for the year in each category. A company
executive must certify that he or she has
examined the OSHA Log and believes that the
annual summary is correct and complete. The
summary must be posted from February 1 to
April 30 of each year in a place where notices
to workers are usually posted, such as an
employee bulletin board.

NOTES:

Classroom Exercise
OSHA 300 Log
1. Refer to the completed OSHA 300 Log example
and emphasize that this form provides the
following information about the workplace:
o How many workers are getting injured or ill
o The types of injuries and illnesses reported
o The jobs and departments where the most
severe injuries or illnesses are occurring
2. Point out where the following information can be
located on the OSHA-300:
o Employees name: Column (B) Note that
employers cannot remove names
o Job Title: Column (C) Can show the most
dangerous jobs
o Where the event occurred: Column (E)
Can show the most hazardous departments
o Describe the injury or illness, parts of body
affected, and object/substance that directly
injured or made person ill: Column (F)
Can show the types of injuries/illnesses and
how people are getting sick or hurt
o Page totals for Columns (G), (H), (I), & (J)
Shows the total number of injuries and
illnesses occurring
12.2013

Refer to Handout #6: OSHA 300

Log example

Sum up the exercise by

emphasizing that it is important
that OSHA injury and illness
records be correctly maintained.
Also, workers have a right to see
the OSHA 300 Log and the posted
OSHA 300A Summary.

Page 20

Introduction to OSHA
2 HOUR LESSON

D. Provide medical exams when required by OSHA

standards and provide workers access to their
exposure and medical records

NOTES:

We discussed access to medical records earlier when

covering worker rights. When you are working with
chemicals or other hazardous substances, your
employer may be required to conduct monitoring or
provide medical examinations that involve you. An
example of this would be if you are working with lead,
such as removing or stripping substantial quantities of
lead-based paints on large bridges and other
structures. Plumbers, welders, and painters are
among those workers most exposed to lead. Your
employer must give you copies of medical or exposure
records involving you if you request them.
E. Not discriminate against workers who exercise
their rights under the Act (Section 11(c))
Section 11(c) of the Act prohibits your employer from
discharging or in any manner retaliating against you or
any worker for exercising your rights under the Act.
Weve covered many of your rights under OSHA
earlier. Can you recall some of them? Depending
upon the circumstances of the case, "discrimination"
can include: firing or laying off; demoting; denying
overtime or promotion; disciplining; reducing pay or
hours, and other actions. If you believe your employer
has discriminated against you because you exercised
your safety and health rights, contact your local OSHA
Office right away. The OSH Act gives you only 30
days to report discrimination.

12.2013

Ask the class to recall some

of their rights under OSHA.
Rights include: right to a workplace
free of hazards, receiving training,
access to injury/illness and
medical records, complaining to
your employer or OSHA about a
safety and health problem,
participating in an OSHA
inspection, and participating or
testifying in any proceeding related
to an OSHA inspection.
OSHA also administers the
whistleblower provisions of 17
other statutes, protecting workers
who report violations of various
trucking, airline, nuclear power and
environmental laws.

Page 21

Introduction to OSHA
2 HOUR LESSON

F. Post OSHA citations and abatement verification

notices

NOTES:

An OSHA citation informs the employer and workers

of the standards violated, the length of time set for
correction, and proposed penalties resulting from an
OSHA inspection. Your employer must post a copy of
each citation at or near places where the violations
occurred for 3 days, or until the violation is fixed
(whichever is longer). Employers also have to inform
workers of what they have done to fix the violation,
allow workers to examine and copy abatement
documents sent to OSHA, and tag cited movable
equipment to warn workers of the hazard.

See Abatement Verification

Regulation, 1903.19, for additional
information.

G. Provide and pay for PPE

As we mentioned earlier, OSHA requires the use of
personal protective equipment (PPE) to reduce
employee exposure to hazards when engineering and
administrative controls are not feasible or effective in
reducing these exposures to acceptable levels.
Employers are required to determine if PPE should be
used to protect their workers. OSHA also requires that
employers pay for most required PPE, except for
uniforms, items worn to keep clean, weather-related
gear, logging boots, and non-specialty safety toe
protective footwear (including steel-toe shoes or steeltoe boots) and non-specialty prescription safety
eyewear, as long as the employer permits the items to
be worn off the job-site.

12.2013

Refer to Handout #7: Employers

Must Provide and Pay for PPE
Ask the class if anyone
wears personal protective
equipment on their job and
discuss the requirement for
employers to provide and pay for
PPE. The Employer Payment for
Personal Protective Equipment
rule was effective on February 13,
2008 and had to be implemented
by May 15, 2008.

Page 22

Introduction to OSHA
2 HOUR LESSON

Examples of PPE that employers must pay for include: NOTES:

Metatarsal foot protection,
Rubber boots with steel toes,
Non-prescription eye protection,
Prescription eyewear inserts/lenses for full face
respirators,
Goggles and face shields,
Fire fighting PPE (helmet, gloves, boots,
proximity suits, full gear),
Hard hat,
Hearing protection, and
Welding PPE.

Questions for Review

1. What are some of the responsibilities employers
have related to OSHA recordkeeping?
2. Which section of the OSH Act prohibits employers
from discriminating against workers for exercising
their safety and health rights?
3. What are some types of PPE that employers must
pay for?

12.2013

Answers:
1. Employers must set up a
reporting system and
inform workers of how to
report, maintain an OSHA300 log and make it
available to workers, post
the annual summary and
report fatalities and the
hospitalization of 3 or
more workers to OSHA.
2. Section 11(c)
3. Hardhats, hearing
protection, etc.

Page 23

Introduction to OSHA
2 HOUR LESSON

Topic 4. What do the OSHA standards say?

A. Types of standards
B. How the standards are organized

NOTES:

Instruction for Topic 4:

1. Discuss Detailed Content section.
2. Conduct the Classroom Exercise on how to
read the OSHA Standards. See page 25.
3. Have the class answer the Questions for
Review.

DETAILED CONTENT for Topic 4:

A. Types of standards

Discuss/Show: Copy of the

OSHA standards book (General
Industry or Construction)

Now, lets talk briefly about the OSHA standards.

OSHA standards fall into four categories: General
Industry, Construction, Maritime, and Agriculture.
OSHA issues standards for a wide variety of
workplace hazards, including:
Toxic substances,
Electrical hazards,
Fall hazards,
Hazardous waste,
Machine hazards,
Infectious diseases,
Fire and explosion hazards, and
Dangerous atmospheres.
In addition, as we discussed previously, where there
are no specific OSHA standards, employers must
comply with the OSH Act's "general duty clause." The
General Duty Clause, Section 5(a)(1), requires that
each employer "furnish ... a place of employment
which [is] free from recognized hazards that are
causing or are likely to cause death or serious
physical harm to his employees.

12.2013

General Duty Clause violations

cited by OSHA can be found on
OSHAs website at:
http://www.osha.gov/oshstats/
index.html
You can query by Hazard
Category, such as Crushing,
Chemical or Guarding to locate
actual violations cited. One
example, from a search using
Crushing, is: An employee was
exposed to crushing hazards when
a scissor lift rolled down a ramp,
pinning him against a backhoe
while he was attempting to move
the lift off a flatbed. Emergency
procedures such as chocking were
not followed.

Page 24

Introduction to OSHA
2 HOUR LESSON

B. How the standards are organized

OSHA standards appear in the Code of Federal
Regulations (CFR). The OSHA standards are broken
down into Parts. Part 1910 is known as the General
Industry Standards. Some of the types of industries
covered by the General Industry standards are
manufacturing, the service sector, and health care.
Part 1926 covers the Construction industry. Parts
1915, 1917 and 1918 are Maritime Industry standards.
Discuss the following:

The CFR is divided into Titles. OSHAs standards

are in Title 29.
Under each Part, such as Part 1926, major blocks
of information are broken into subparts. For
example, Subpart C is named General Safety and
Health Provisions. Subpart C contains sections
1926.20 through 1926.35.
All OSHA standards are available on OSHAs
website. You can look them up by the standard
number or do a search by topic.

NOTES:

If time permits and Internet access

is available, show the class how to
locate OSHA standards online.
You may also wish to show the
class how to locate the Most
Frequently Cited (MFC) Standards
online at:
http://www.osha.gov/pls/imis/cited
standard.html
Note: From the MFC website, to
search SIC, use C for Construction
or D for Manufacturing, Maritime
SICs include 373 and 449.

Classroom Exercise
OSHA Standards
1. Ask the class to briefly look at How to Read the
OSHA Standards handout.
2. Ask the class the questions on the standards and
discuss the responses.

Refer to Handout #8a, #8b or

#8c: Use #8a for General Industry;
Use #8b for Construction; Use #8c
for Maritime Industry

Questions
Standards Answers:
For General Industry:
General Industry:
1. What is the Subpart for Personal Protective
1. Subpart I
Equipment?
2. Subpart O
3. Hazardous Materials in
2. What is the Subpart for Machinery and Machine
General Industry
Guarding?
Construction:
3. What topic does 1910, Subpart H cover?
For Construction:
1. What is the Subpart for Fall Protection?
2. What is the Subpart for Fire Protection and
Prevention?
3. What topic does 1926, Subpart K cover?
12.2013

1. Subpart M
2. Subpart F
3. Electrical Standards in
Construction

Page 25

Introduction to OSHA
2 HOUR LESSON

Standards Answers:
For Maritime Industry:
Maritime Industry:
1. What is the 29 CFR 1915 Subpart for Tools and
1. Subpart H
Related Equipment?
2. Subpart E
2. What is the 29 CFR 1917 Subpart for Personal
3. Handling Cargo
Protection?
3. What topic does 29 CFR 1918, Subpart H
cover?

Questions for Review

1. What are the OSHA Construction standards also
called?
2. What are the General Industry standards also
called?

Answers
1. Part 1926
2. Part 1910
3. Maritime Industry Standards

3. What are 29 CFR Parts 1915, 1917 and 1918

referred to as?

12.2013

Page 26

Introduction to OSHA
2 HOUR LESSON

Topic 5. How are OSHA inspections conducted?

A. Inspection priorities
B. Stages of an inspection
C. Citations and penalties
D. Appeals process

NOTES:

Instruction for Topic 5:

1. Discuss Detailed Content section.
2. Ask the class if anyone has been at work during
an OSHA inspection. If so, ask them to briefly
share their experience.
3. Have the class answer the Questions for
Review.
Detailed Content for Topic 5:
A. Inspection priorities
The OSH Act authorizes OSHA compliance safety and
health officers (CSHOs) to conduct workplace
inspections at reasonable times. OSHA conducts
inspections without advance notice, except in rare
circumstances (for example, when there is a report of
an Imminent Danger). In fact, anyone who tells an
employer about an OSHA inspection in advance can
receive fines and a jail term.
Since not all eight million worksites covered by OSHA
can be inspected, the agency has a system of
inspection priorities.
Priority

Category of Inspection

1st

Imminent Danger

2nd

Fatality/Catastrophe

3rd

Complaints/Referrals

4th

Programmed Inspections

12.2013

Page 27

Introduction to OSHA
2 HOUR LESSON

NOTES:
1st. Imminent Danger has top priority. This is a
condition where there is reasonable certainty a
danger exists that can be expected to cause death
or serious physical harm immediately (or before the
danger can be removed through normal
enforcement). An example could be workers
working in an unstable trench that has no shoring
or sloping. In such cases, OSHA may contact the
employer and try to have workers removed from
the danger right away. In any case, a CSHO will
make an inspection, no later than one day after the
report was received.
2nd. Fatalities and Catastrophes are next in
priority. As we learned earlier, employers must
report to OSHA any worker fatality or the
hospitalization of three or more employees. OSHA
starts these investigations as soon as possible
after getting the report. CSHOs gather evidence
and interview the employer, workers, and others to
determine the causes of the event and whether
violations occurred.
3rd. Complaints and Referrals are OSHAs third
priority. A worker or worker representative can file
a complaint about a safety or health hazard in the
workplace. Generally, it is necessary for the
complaint to be written and signed for OSHA to
conduct an inspection. In other cases, OSHA may
contact the employer by phone, email or fax.
Referrals usually are from a government agency,
such as NIOSH or a local health department. They
are handled the same way as complaints.
4th. Programmed Inspections are the fourth
priority. These inspections cover industries and
employers with high injury and illness rates,
specific hazards, or other exposures. There may
also be special emphasis programs in just one
OSHA region or certain area offices, based on
knowledge of local industry hazards.

12.2013

Page 28

Introduction to OSHA
2 HOUR LESSON

OSHA also conducts Follow-up and Monitoring

Inspections. These inspections are made as needed,
and take priority over Programmed Inspections. A
follow-up is made to see if violations cited on an
earlier inspection were fixed. Monitoring inspections
are made to make sure hazards are being corrected
and workers are protected whenever a long period of
time is needed for a hazard to be fixed.

NOTES:

B. Stages of an inspection
There are four major stages of an OSHA inspection:
Presenting Credentials; the Opening Conference; the
Walkaround; and the Closing Conference.
1. Presenting Credentials
When arriving at the workplace, the CSHO finds out
who is in charge and presents his or her credentials.
An employer can require OSHA to get a warrant
before an inspection is made.
2. Opening Conference
The CSHO finds out if workers are represented and, if
so, makes sure that the worker representative
participates in all phases of the inspection. If the
employer or worker representative objects to a joint
conference, separate conferences are held.

IF

Selecting worker representatives

THEN

Workers are represented by a

recognized bargaining
representative
There is a plant safety
committee and no recognized
bargaining representative
There is neither a recognized
bargaining representative nor
a plant safety committee

There is no authorized worker

representative

12.2013

The union usually designates the

worker representative to accompany
the CSHO
The worker members of that
committee or the workers at large
will designate the worker
representative
The workers themselves may select
their representative, or the CSHO
will determine if any other worker
would be suitable to be a
representative
The CSHO must consult with a
reasonable number of workers
concerning safety and health
matters in the workplace

Page 29

Introduction to OSHA
2 HOUR LESSON

The opening conference is generally brief so that the

CSHO may quickly start the walkaround.

NOTES:

In the opening conference, the CSHO:

Explains why OSHA selected the worksite
for inspection;
Obtains information about the company,
including a copy of the hazard assessment
to see what personal protective equipment
is necessary;
Explains the purpose of the visit, the scope
of the inspection, walkaround procedures,
worker representation, private worker
interviews, and the closing conference; and
Determines whether the facility falls under
any inspection exemption through a
voluntary compliance program (for example,
if an OSHA-funded consultation visit is in
progress).
At the start of the inspection, the CSHO checks the
injury and illness records. The CSHO also checks that
the OSHA poster is displayed and that the OSHA
Summary of Injuries and Illnesses is posted from
February 1 to April 30 each year. Other records
related to safety and health issues may be requested.
3. The Walkaround
After the opening conference, the CSHO, along with
the employer and worker representatives, proceed
through the workplace, inspecting work areas for
potentially hazardous working conditions. Apparent
violations are brought to the attention of employer and
worker representatives as the CSHO observes and
documents them. The CSHO may also interview
workers, take photographs or video, and monitor
worker exposure to noise, air contaminants, or other
substances. The CSHO will conduct all worker
interviews in private, although workers may request
that a union representative be present.

12.2013

Page 30

Introduction to OSHA
2 HOUR LESSON

4. Closing Conference
After the walkaround, the CSHO holds a closing
conference with the employer and the worker
representatives, either jointly or separately. When the
employer does not want to have a joint conference,
the CSHO will normally hold the conference with the
worker representative first, so that worker input is
received before employers are informed of proposed
citations.

NOTES:

During the closing conference, apparent violations that

have been observed on the walkaround and estimated
times for correction are discussed. Employers are
informed of their rights and responsibilities related to
the inspection. Both employer and worker
representatives are told of their rights to take part in
any future meetings and their contest rights. No
citations are given out at this time. They are sent in
the mail at a later date (no later than 6 months after
the inspection).
C. Citations and penalties
The CSHO takes the findings back to the office and
writes up a report. The Area Director reviews it and
makes the final decision about the citations and
penalties.
Citations inform the employer and workers of:
Regulations and standards the employer
allegedly violated;
Any hazardous working conditions covered by
the OSH Acts General Duty Clause;
The proposed length of time set for abatement
of hazards; and
Any proposed penalties.
Citations are sent by certified mail to the facility. The
employer must post a copy of each citation at or near
the place the violation occurred for 3 days or until it is
fixed. Employers must also inform workers and their
representatives of the correction they make.
12.2013

Page 31

Introduction to OSHA
2 HOUR LESSON

Penalties are based on violation type. OSHA may cite

the following violations and propose the following
penalties:
VIOLATION TYPE

WILLFUL
A violation that the
employer intentionally and
knowingly commits or a
violation that the employer
commits with plain
indifference to the law.

PENALTY
OSHA may propose
penalties of up to $70,000
for each willful violation,
with a minimum penalty of
$5,000 for each willful
violation.

NOTES:
Criminal Willful violations,
which involve the death of a
worker, may have a penalty of
up to $250,000 for an
individual and $500,000 for an
organization, or by up to 6
months in jail.

SERIOUS
A violation where there is
substantial probability that
death or serious physical
harm could result and that
the employer knew, or
should have known, of the
hazard.

There is a mandatory
penalty for serious
violations which may be up
to $7,000.

OTHER-THAN-SERIOUS
A violation that has a direct
relationship to safety and
health, but probably would
not cause death or serious
physical harm.

REPEATED
A violation that is the same or
similar to a previous violation.

OSHA may propose a

penalty of up to $7,000 for
each other-than-serious
violation.
OSHA may propose
penalties of up to $70,000
for each repeated violation.

Ask the class if they

can think of an
example of:
a serious violation. (An
example would be not
providing guarding or fall
protection for workers on a
25 foot scaffold. The
resulting fall would most
likely result in death,
broken bones and/or other
serious injuries.)
an other-than-serious
violation. (An example of
this type of violation could
be an area with poor
housekeeping, creating a
tripping hazard. The most
likely result would be
abrasions or bruises.
However, this would only
be the case if there were
no sharp objects, broken
glass, etc. in the area.),

OSHA may also assess penalties to employers for the

following:

Failure to Abate. OSHA may propose an

additional penalty of up to $7,000 for each day
an employer fails to correct a previously cited
violation beyond the required date.

Falsifying Information. Under the OSH Act, an

employer providing false information to OSHA
can receive a fine of up to $10,000 or up to 6
months in jail, or both.

12.2013

Page 32

Introduction to OSHA
2 HOUR LESSON

Violation of Posting. The employer has to post NOTES:

citations and abatement verification for three
days or until the hazard is corrected. The
posting has to be near the violation or at a
central location. Failure to follow these
instructions can result in a penalty of up to
$7,000 for each violation.

OSHA may adjust a penalty downward depending on

the gravity of the violation, the employer's good faith
(efforts to comply with the Act), history of previous
violations, and size of business.
D. Appeals process
Employers and workers each have rights to disagree
with (or appeal) parts of an OSHA citation. Workers
and their representatives may request an informal
conference with OSHA to discuss the inspection,
citations, penalties or a notice of contest (if filed by the
employer). Workers may also contest the abatement
time for any violation and an employer's petition for
modification of abatement (PMA), but they cannot
contest citations or penalties. If you, as a worker, plan
to contest an abatement time, you should provide
information to support your position.

Employers have the right to

request an extension of time
for an abatement date if they
cannot meet the time stated on
the citation for a cited item.
This is called a petition for
modification of abatement, or
PMA
If a violation or abatement date
is contested by the employer,
the situation does not have to
be fixed until there is a final
legal order. If only the penalty
is contested, the violation must
be fixed by the date in the
citation.

The employer has more rights than workers related to

citations. Employers may request an informal
conference with OSHA to discuss the case. They can
also reach a settlement agreement with OSHA that
adjusts citations and penalties in order to avoid
prolonged legal disputes.
If an employer decides to contest the citation, the
abatement date, and/or the proposed penalty, this
must be done, in writing, within the 15-working day
contest period. The area director forwards the notice
of contest to the Occupational Safety and Health
Review Commission (OSHRC). An administrative law
judge decides the case.
12.2013

Page 33

Introduction to OSHA
2 HOUR LESSON

Both workers and the employer have the right to

participate in the hearing and request a further review
of the judge's decision by the commission.
Questions for Review
1. Give an example of a reason why OSHA would
conduct an inspection at your workplace.
2. What are the types of OSHA violations?

12.2013

NOTES:

Answers
1. If a worker files a
complaint, if there is a
fatality, if there is an
imminent danger situation,
etc.
2. Willful, serious, other-thanserious, repeated and
Criminal/Willful.

Page 34

Introduction to OSHA
2 HOUR LESSON

Topic 6. Where can you go for help?

A. Sources within the workplace/worksite
B. Sources outside the workplace/worksite
C. How to file an OSHA complaint

NOTES:

Instruction for Topic 6:

1. Discuss Detailed Content section.
2. Conduct Small Group Activity: Completing an
OSHA Complaint. See page 40.
3. Have the class answer the Questions for
Review
Detailed Content for Topic 6:
A. Sources within the workplace/worksite
There are many resources available to you if you
want to find out more information about a safety or
health issue in your workplace. Some sources are:

Employer or supervisor, co-workers and union

representatives OSHA encourages workers and
employers to work together to reduce hazards. If
possible, you should discuss safety and health
problems with your employer. You can also talk
over your concerns with other workers or your
union representatives (if there is a union).

Safety Data Sheet (SDS) for information on

chemicals Earlier in this session, we talked
about the Safety Data Sheet, also called an SDS,
and what information it supplies. If you are working
with a chemical, the SDS can give you important
information about its hazards and the precautions
and personal protective equipment needed to work
safely with it.

12.2013

Page 35

Introduction to OSHA
2 HOUR LESSON

Labels and warning signs Labels and signs can NOTES:

show hazard information to workers and can be
useful in providing additional information and
making you aware of a potential safety or health
hazard. However, signs are not intended to take
the place of actual hazard correction. For example,
a Danger sign on an unguarded piece of
machinery does not meet OSHA requirements
because the hazard is still present. OSHA
standards such as those for hazard
communication, egress, confined space and
Bloodborne Pathogens require labels and signs.
The employer must make sure that each sign or
label posted can be understood by all workers, so
the signs must be bilingual if workers do not
understand or read English.

Employee orientation manuals or other training

materials Orientation manuals and training
materials about your job should include information
about how to work safely. As we discussed earlier
in this session, employers are required to provide
training to workers exposed to certain hazards,
including chemicals, falls, and confined spaces. All
manuals and training materials should be written
clearly and spell out what you need to know about
your job hazards. They can also serve as a
resource if you have questions or concerns at a
later date.

Work tasks and procedures instruction A

written job or task instruction can provide
information about the proper and safe way to
perform a job. OSHA considers some jobs and
tasks very hazardous, such as locking out
machinery, and requires employers to have written
procedures. If you have questions about a new job
or task, or a job or task that has changed, be sure
to ask for the written procedures and for additional
training on them.

12.2013

Page 36

Introduction to OSHA
2 HOUR LESSON

B. Sources outside the workplace/worksite

NOTES:

If you cannot find out the safety and health information

you need in your workplace, there are many resources
available outside the workplace.

Refer to Handout #9: Safety &

Health Resources

Refer to Handout #10:

Navigating the OSHA Website

OSHA website: http://www.osha.gov and OSHA

offices
If you have internet access, you will find that the
OSHA website has a lot of safety and health
information and links to resources that can help you.
For example, from the Home Page, you can:
Find information in Spanish from the OSHA en
Espaol page,
Locate Fact Sheets and QuickCards by going to
the Publications page.
o OSHA Fact Sheets provide basic
background information on safety and
health hazards, and
o QuickCards are small, laminated cards
that provide brief, plain language safety
and health information for workers. For
example, there are QuickCards on fall
hazards, carbon monoxide, and
pneumatic nail gun safety.
You can contact OSHA by calling or visiting your local
area or regional office for safety and health information
or to discuss filing a complaint. Compliance
Assistance Specialists in the area offices conduct
many training sessions and have training materials
and information that can be useful.

OSHA website:
http://www.osha.gov ; Show the
links to OSHA en Espaol, Fact
Sheets and QuickCards, etc. If
time permits, show how to
conduct a search on a safety
and health topic or hazard. For
example, if you put Lead in
the Search Box, you get results
including the standards in
General Industry and
Construction, as well as Safety
and Health Topics pages and a
publication on lead exposure in
construction.

Locate the appropriate OSHA

area or regional office contact
information for your audience
and provide it to the class.

Show the class the NIOSH

NIOSH is OSHAs sister agency, with a focus on
website: www.cdc.gov/niosh
research and training. NIOSH can be a great resource
for workers. NIOSH also conducts Health Hazard
Evaluations (HHEs) of workplaces in cases where
workers are getting sick from an unknown

12.2013

Page 37

Introduction to OSHA
2 HOUR LESSON

cause or are exposed to an agent or working condition

that is not regulated by OSHA. A worker can request
an HHE if he or she is currently an employee at the
workplace of concern and has the signatures of two
other workers.

NOTES:

Other resources that can help you get information on

safety and health concerns include:

12.2013

OTI Education Centers (OTIEC) and other

University occupational and environmental
health programs. The OTIECs offer the most
popular OSHA courses and a variety of safety
and health programs including community
outreach efforts, Spanish-language courses,
and youth initiatives.
Doctors, nurses, and other health care
providers can be a resource on the health
effects of toxic substances, proper medical and
first aid treatment, and other health-related
issues. If you are discussing a health concern
with your health care provider, try to provide
them with as much information about the
chemical or substance as possible. For
example, if you are getting headaches at work,
try to get the names and SDSs or labels of the
chemicals to which you are exposed.
Public libraries have books, journals and
magazines on various safety and health topics,
as well as internet access.
Other local, community-based resources, such
as the National Council for Occupational Safety
and Health (COSH) and local COSH groups in
California, New England, the Northeast, the
Midwest and the South, can be a valuable
resource. COSH organizations around the U.S.
are committed to promoting worker health and
safety through training, education, and
advocacy.

For additional information on

OTI Education Centers, see
http://www.osha.gov/
dte/edcenters/index.html

For additional information on

COSH groups, see:
http://www.coshnetwork.org/

Page 38

Introduction to OSHA
2 HOUR LESSON

C. How to file an OSHA complaint

If you, your co-workers and/or your union
representative determine that an OSHA inspection is
needed to get workplace hazards corrected, you have
several options.

You can download the complaint form from

OSHAs website, complete it and mail or fax it
to OSHA. A written, signed complaint submitted
to the OSHA area or State Plan office is most
likely to result in an onsite inspection.
You can file a complaint online. However, most
online complaints are handled by OSHAs
phone/fax system, which means they are
resolved informally over the phone.
You can telephone or visit your local regional or
area office to discuss your concerns. After the
discussion, OSHA staff can give or send you a
complaint form if you wish to file.
Note that if a hazard is life-threatening, call the
Regional or local office or 1-800-321-OSHA
immediately.

NOTES:
A representative can also be
an attorney or any person
acting in a bona fide
representative capacity, such
as clergy, social workers,
spouses, government officials
and nonprofit groups.
Refer to Handout #11:
Identifying Safety and Health
Problems in the Workplace

The complaint will be

evaluated by OSHA to
determine if an inspection will
be conducted. For OSHA to
conduct an inspection, there
must be reasonable grounds
to believe that a violation of
the OSH Act or an OSHA
standard exists.

Completing the complaint form

Highlight the following about the complaint form prior
to the Small Group Activity:
Be specific and include appropriate details: The
information on the complaint form may be the only
description of the hazard that the inspector will see
before the inspection. The inspector will base his or
her research and planning on this information.
Establishment Name, Address, & Type of
Business: Be thorough and specific. The
inspectors research on the company and the
industrys hazards will be based on this
information.

12.2013

Page 39

Introduction to OSHA
2 HOUR LESSON

NOTES:
Hazard Description/Location: The hazard
description is the most important part of the form.
Your answer should explain the hazards clearly. If
your complaint is about chemicals, identify them
whenever possible and attach copies of labels or
SDSs if you can. Identify the location so the
inspector will know where to look.
Has this condition been brought to the attention of
the employer or another government agency? You
should indicate on the form if you have tried to get
the employer to fix the hazard before filing the
complaint. Also, if another agency, such as a local
fire or building department, has been notified of
these hazards, OSHA may want to consult with
them.
Do NOT reveal my name: OSHA will keep your
name off the complaint, if you wish. Remember that
discrimination for health and safety activity is
illegal. If you are a union representative, you may
wish to have your name on the complaint.
Signature and address: It is important to sign the
complaint if you want OSHA to conduct an onsite
inspection. Also, your address will allow OSHA to
send copies of inspection related materials to you.

Small Group Activity

Filing an OSHA Complaint
Have the students break into groups of 3-5 people.
1. Refer to the Complaint form handouts which
include the form, tips for completing the form,
and complaint scenarios.
2. Have the class discuss the complaint scenario
in their groups.
3. Ask each group to determine what information
would be important to put on the complaint form
and if any additional information is needed. Use
the complaint scenario answers as a reference.
4. After a few minutes, bring class back together.
5. Ask for volunteers to share the information their
groups decided was important and what other
information should be added.

12.2013

Refer to Handout #12a,

#12b, or #12c Filing an
OSHA Complaint: Use #12a
for General Industry; Use
#12b for Construction; Use
#12c for Maritime Industry
Explain to the students the
handout consists of tips on
completing the form, the
scenario specific to their
industry, and the OSHA
Complaint form.
Sum up the activity by
stressing that it is important to
be specific and accurate
when completing an OSHA
complaint, as this is the
information the CSHO will use
to research, plan and begin
the investigation.
Page 40

Introduction to OSHA
2 HOUR LESSON

Questions for Review

1. What are some resources inside the workplace
that will help you find information on safety and
health issues?
2. What are some resources outside the
workplace that will help you find information on
safety and health issues?

12.2013

Answers:
1. Co-workers, union rep,
supervisor, SDS, labels,
manuals, etc.
2. OSHA, NIOSH,
Educational Centers,
Community
Organizations, etc.

Page 41

Introduction to OSHA
2 HOUR LESSON

Session Summary
During this session, you have been introduced to
basic information about your safety and health at
work. We have covered:
The importance of OSHA, including the history of
safety and health regulation leading to the
creation of OSHA and OSHAs mission;
Worker rights under OSHA;
Employer responsibilities;
OSHA standards;
OSHA inspections; and
Safety and health resources, including how to file
a complaint.

12.2013

NOTES:

Ask the class if there is any

material that needs to be
covered in more detail.

Page 42

Introduction to OSHA
2 HOUR LESSON

Conduct Test Answer Key

Distribute the Introduction to OSHA Check Yourself Test Questions.
12 Question Test ANSWER KEY:
1. b
2. d
3. a
4. c
5. d
6. c
7. a
8. c
9. a
10. d
11. b
12. b
Discuss the test answers with the class.

The following sessions will provide training on how you can recognize specific hazards
in your workplace or worksite.
Thank participants for their time, attention, and involvement in the session.

12.2013

Page 43

Introduction to OSHA
2 HOUR LESSON

References:

12.2013

OSHA website and publications

The Center for Construction Research and Training (CPWR); SMART MARK
the Sign of a Smarter Workplace, 8484 Georgia Avenue, Suite 1000, Silver
Spring, MD 20910
The International Union of Operating Engineers (IUOE) National HAZMAT
training material
The Labor Occupational Health Program of the University of California
booklets and guidance
The National Institute of Environmental Health Sciences (NIEHS) curriculum
clearinghouse products
The National Safety Education Center
National Institute for Occupational Safety and Health (NIOSH) worker training
materials
Service Employees International Union (SEIU) training materials

Page 44

Introduction to OSHA
2 HOUR LESSON

APPENDIX
A.
B.
C.
D.

12/2013

SDS Explanation
Handout #12a-c Answer Sheet
Check Yourself Test Questions Answer Sheet
Check Yourself Test Questions Student Copy

Introduction to OSHA
2 HOUR LESSON

12/2013

APPENDIX A
SDS EXPLANATION USE WITH HANDOUT #3

nation

SAFETY DATA SHEET (SDS) EXPLANATION

Safety Data Sheets (SDS) should be available through your supervisor. The Hazard Communication
Standard (HCS) requires chemical manufacturers, distributors, or importers to provide Safety Data
Sheets (SDSs) (formerly known as Material Safety Data Sheets or MSDSs) to communicate the hazards of
hazardous chemical products. As of June 1, 2015, the HCS will require new SDSs to be in a uniform
format, and include the section numbers, the headings, and associated information under the headings
below:
Section I
Identification

This section identifies the chemical on the SDS as well as the

recommended uses. It also provides the essential contact
information of the supplier.

Section 2
Hazard(s) Identification

This section identifies the hazards of the chemical presented

on the SDS and the appropriate warning information
associated with those hazards. This section includes the
hazard classification of the chemical, a signal word, a hazard
statement, pictograms, a precautionary statement, and
description of any hazards not otherwise classified.

Section 3
Composition/Information on
Ingredients

This section identifies the ingredient(s) contained in the

product indicated on the SDS, including impurities and
stabilizing additives. This section includes information on
substances, mixtures, and all chemicals where a trade secret
is claimed.
This section describes the initial care that should be given by
untrained responders to an individual who has been
exposed to the chemical.

Section 4
First-Aid Measures
Section 5
Fire-Fighting Measures

This section provides recommendations for fighting a fire

caused by the chemical.

Section 6
Accidental Release Measures

This section provides recommendations on the appropriate

response to spills, leaks, or release, including containment
and clean-up practices to prevent or minimize exposure to
people, properties, or the environment. It may also include
recommendations distinguishing between responses for
large and small spills where spill volume has significant
impact on the hazard.

Section 7
Handling and Storage

This section provides guidance on the safe handling

practices and conditions for safe storage of chemicals.

Section 8
Exposure Controls/Personal
Protection

This section indicates the exposure limits, engineering

controls, and personal protective measures that can be used
to minimize worker exposure.

Section 9 Physical and Chemical

Properties

This section identifies physical and chemical properties

associated with the substance or mixture

12.2013

Page A1

APPENDIX A
SDS EXPLANATION USE WITH HANDOUT #3

Section 10 Stability and Reactivity

This section describes the reactivity hazards of the chemical

and the chemical stability information

Section 11 Toxicological Information

This section identifies toxicological effects information or

indicates that such data is not available.

Section 12 Ecological Information

(non-mandatory)

This section provides information to evaluate the

environmental impact of the chemical(s) if it were released
into the environment.

Section 13 Disposal Considerations

(non-mandatory)

This section provides guidance on proper disposal practices,

recycling or reclamation of the chemical(s) or its container,
and safe handling practices.

Section 14 Transportation
Information( non-mandatory)

This section provides guidance on classification information

for shipping and transporting hazardous chemical(s) by road,
air, rail, or sea.

Section 15 Regulatory Information

(non-mandatory)

This section identifies the safety, health and environmental

regulations specific for the product that is not indicated
elsewhere on the SDS.

Section 16 Other Information

This section indicates when the SDS was prepared or when

the last known revision was made.

12.2013

Page A2

APPENDIX A
SDS EXPLANATION USE WITH HANDOUT #3

12.2013

Page A1

APPENDIX B
FILING AN OSHA COMPLAINT SCENARIO ACTIVITY ANSWER SHEETS #12a, #12b, AND #12c

APPENDIX B: Handout #12a, #12b, #12c Answer Sheet

#12a: General Industry Complaint Scenario Answer Sheet

Use the following scenario to determine what information should be
put on an OSHA complaint form. Is any additional information
needed?
Important information is bolded:
You have worked at Ben Brothers Woodworking for 8 years as a janitor.
Ben Brothers is located at 88 Wren Street, Anytown, USA, 40001. The
company makes and refinishes office furniture. You usually work the
second shift, but come in early sometimes. You and at least 3 of your
co-workers have been getting headaches when you are working in
the warehouse and the propane-operated forklift is running. You
have had headaches over the past two months, at least twice a
week.
The forklift operator told you that there are a lot of problems with
the forklift and it needs to be replaced. You reported your headaches
to your supervisor. She told you to go outside until you felt better
and that there was nothing more she could do. You did some research
and found out that exposure to propane in a confined, unventilated area can
cause headaches, dizziness, difficulty breathing and unconsciousness. There
is no monitoring of the air in the warehouse. There is no union at the
facility. You decide to file a complaint with OSHA.
Additional information needed:
Site phone; mailing address phone; Management Official in charge. Remind
participants that their contact information and signature are very important.
NOTES:
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________

12.2013

Page B1

APPENDIX B
FILING AN OSHA COMPLAINT SCENARIO ACTIVITY ANSWER SHEETS #12a, #12b, AND #12c

#12b: Construction Complaint Scenario Answer Sheet

Use the following scenario to determine what information should be
put on an OSHA complaint form. Is any additional information
needed?
Important information is bolded:
You are a construction worker for ABC, Inc, 1000 Sweet Road, Anytown,
USA, 40001. ABC does non-residential plumbing, heating and airconditioning work. You have worked for ABC for 3 years. You, along with
7 co-workers, have been installing sheetmetal ductwork in the lower level
of the Anytown Shopping Mall, which is undergoing renovation, for the
past few weeks. The site is located in the Northwest quadrant, in the
basement of the anchor store, located at 555 Times Drive, in
Anytown. One of your co-workers has been operating a 65horsepower concrete cutting saw in the same area. The saw is being
run in the propane mode. You and several co-workers get headaches
from the fumes whenever the saw is used and have told your
supervisor about the problem. The supervisor said that nothing could
be done, because the General Contractor, CAB Management, has
control over the site and this job will be complete in another month.
You did some research and found out that exposure to propane in a
confined, unventilated area can cause headaches, dizziness, difficulty
breathing and unconsciousness. There is no ventilation or monitoring of
the air in the area.
After talking to your union representative, you decide to file a
complaint with OSHA.
Additional information needed:
Site phone; mailing address phone; Management Official in charge. Remind
participants that their contact information and signature are very important.
NOTES:
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________

12.2013

Page B2

APPENDIX B
FILING AN OSHA COMPLAINT SCENARIO ACTIVITY ANSWER SHEETS #12a, #12b, AND #12c

#12c: Maritime Industry Complaint Scenario Answer Sheet

Use the following scenario to determine what information should be
put on an OSHA complaint form. Is any additional information
needed?
Important information is bolded:
You are a longshoreman who operates a propane-operated forklift
truck for ABC, Inc, 1000 Pier Street, Anytown, USA, 40001. ABC is
involved in terminal operations and warehousing. You have worked for
ABC for 3 years. For the past week, you have been transporting rolls
of coiled steel from a storage area to a different section of the
longshoring terminal, due to hurricane damage to another part of the
terminal. As a result, you have been working inside the terminal more than
you usually do. The area you are working in is somewhat confined and
crowded due to extra storage. You have noticed that you are getting
headaches and feeling dizzy. Two other co-workers working with
you are also having the same symptoms. You are concerned that the
forklift needs maintenance, and have asked your supervisor to have
it checked out, but he looked it over and said it didnt need service.
You and your union representative requested air monitoring of the
area, but your supervisor did not agree. There is limited ventilation
in the area. You did some research and found out that exposure to propane
in a confined, unventilated area can cause headaches, dizziness, difficulty
breathing and unconsciousness.
After talking to your union representative, you decide to file a
complaint with OSHA.
Additional information needed:
Phone numbers; Management Official in charge. Remind participants that
their contact information and signature are very important.
NOTES:
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________

12.2013

Page B3

APPENDIX B
FILING AN OSHA COMPLAINT SCENARIO ACTIVITY ANSWER SHEETS #12a, #12b, AND #12c

12.2013

Page B4

APPENDIX C
CHECK YOURSELF TEST QUESTIONS CORRECT ANSWER IS BOLD

APPENDIX C: Check Yourself Test Questions Answer Sheet

1. OSHAs mission is to:

a. Protect the safety and health of the general public.
b. Protect the safety and health of Americas workers.
c. Ensure that all workers receive the federal minimum wage.
d. Ensure that all workers receive adequate workers compensation payments.
2. The creation of OSHA provided this important right to workers:
a. The right to equal employment opportunities.
b. The right to privacy.
c. The right to pension benefits.
d. The right to a safe and healthful workplace.
3. A Safety Data Sheet (SDS) gives information about:
a. Hazardous chemicals.
b. Injuries in the workplace.
c. Medical examinations.
d. Machinery maintenance.
4. Among the rights related to OSHA recordkeeping, workers have the right to
review:
a. All first aid treatment forms.
b. All Workers Compensation forms.
c. The OSHA 300 Log and the OSHA 300A Summary.
d. Medical and exposure records for all workers.
5. During an OSHA inspection:
a. Worker representatives are not permitted to accompany the inspector.
b. You may not describe safety and health concerns you have to the inspector.
c. Employers determine which workers are interviewed.
d. You have the right to talk to the inspector privately.
6. The right of workers to seek safety and health on the job without fear of
punishment is spelled out in:
a. State laws.
b. The OSHA standards.
c. Section 11(c) of the OSH Act.
d. The General Duty Clause.

12.2013

Page C1

APPENDIX C
CHECK YOURSELF TEST QUESTIONS CORRECT ANSWER IS BOLD

7. One of the main responsibilities employers have under OSHA is to:

a. Provide training required by OSHA standards.
b. Reduce air pollution in the environment.
c. Conduct energy audits.
d. Notify OSHA of any workplace injury or illness.
8. OSHA requires that employers pay for most required personal protective
equipment (PPE), including:
a. Uniforms.
b. Logging boots.
c. Hard hats.
d. Weather-related gear.
9. The OSHA standards for Construction and General Industry are also known as:
a. Part 1926 and Part 1910.
b. Part 1915 and Part 1917.
c. Codes 501 through 1000.
d. Construction and GI Registers.
10. What type of OSHA inspection is conducted when immediate death or serious harm
is likely?
a. Complaint.
b. Programmed.
c. Referral.
d. Imminent danger.
11. When the employer receives an OSHA citation, it must be:
a. Copied and mailed to each worker.
b. Posted for 3 days or until the violation is fixed.
c. Contested and filed with the courts.
d. Signed and returned to OSHA.
12. If you feel that an OSHA inspection is needed to get hazards corrected at your
workplace, which is your best option?
a. File a complaint online.
b. Submit a written, signed complaint with specific hazard information.
c. Request a Health Hazard Evaluation from NIOSH.
d. Submit an unsigned complaint form to OSHA.

12.2013

Page C2

APPENDIX D
CHECK YOURSELF TEST QUESTIONS STUDENT

APPENDIX D: Check Yourself Test Questions Student Copy

1. OSHAs mission is to:

a. Protect the safety and health of the general public.
b. Protect the safety and health of Americas workers.
c. Ensure that all workers receive the federal minimum wage.
d. Ensure that all workers receive adequate workers compensation payments.
2. The creation of
a. The right to
b. The right to
c. The right to
d. The right to

OSHA provided this important right to workers:

equal employment opportunities.
privacy.
pension benefits.
a safe and healthful workplace.

3. A Safety Data Sheet (SDS) gives information about:

a. Hazardous chemicals.
b. Injuries in the workplace.
c. Medical examinations.
d. Machinery maintenance.
4. Among the rights related to OSHA recordkeeping, workers have the right to
review:
a. All first aid treatment forms.
b. All Workers Compensation forms.
c. The OSHA 300 Log and the OSHA 300A Summary.
d. Medical and exposure records for all workers.
5. During an OSHA inspection:
a. Worker representatives are not permitted to accompany the inspector.
b. You may not describe safety and health concerns you have to the inspector.
c. Employers determine which workers are interviewed.
d. You have the right to talk to the inspector privately.
6. The right of workers to seek safety and health on the job without fear of
punishment is spelled out in:
a. State laws.
b. The OSHA standards.
c. Section 11(c) of the OSH Act.
d. The General Duty Clause.

12.2013

Page D1

APPENDIX D
CHECK YOURSELF TEST QUESTIONS STUDENT

7. One of the main responsibilities employers have under OSHA is to:

a. Provide training required by OSHA standards.
b. Reduce air pollution in the environment.
c. Conduct energy audits.
d. Notify OSHA of any workplace injury or illness.
8. OSHA requires that employers pay for most required personal protective
equipment (PPE), including:
a. Uniforms.
b. Logging boots.
c. Hard hats.
d. Weather-related gear.
9. The OSHA standards for Construction and General Industry are also known as:
a. Part 1926 and Part 1910.
b. Part 1915 and Part 1917.
c. Codes 501 through 1000.
d. Construction and GI Registers.
10. What type of OSHA inspection is conducted when immediate death or serious harm
is likely?
a. Complaint.
b. Programmed.
c. Referral.
d. Imminent danger.
11. When the employer receives an OSHA citation, it must be:
a. Copied and mailed to each worker.
b. Posted for 3 days or until the violation is fixed.
c. Contested and filed with the courts.
d. Signed and returned to OSHA.
12. If you feel that an OSHA inspection is needed to get hazards corrected at your
workplace, which is your best option?
a. File a complaint online.
b. Submit a written, signed complaint with specific hazard information.
c. Request a Health Hazard Evaluation from NIOSH.
d. Submit an unsigned complaint form to OSHA.

12.2013

Page D2