Isa-12.01.01. Def. Electr. Areas Clasificadas

AMERICAN NATIONAL STANDARD
ANSI/ISA12.01.011999
Formerly ISAS12.01.011999
Definitions and Information

Pertaining to Electrical
Apparatus in Hazardous
(Classified) Locations
NOTICE OF COPYRIGHT
This is a copyrighted document and may not be copied or distributed in any
form or manner without the permission of ISA. This copy of the document was
made for the sole use of the person to whom ISA provided it and is subject to
the restrictions stated in ISAs license to that person. It may not be provided to
any other person in print, electronic, or any other form. Violations of ISAs
copyright will be prosecuted to the fullest extent of the law and may result in
substantial civil and criminal penalties.
Approved 21 November 2000

TM
ISAThe Instrumentation,
Systems, and
Automation Society
ANSI/ISA-12.01.01-1999
Definitions and Information Pertaining to Electrical Apparatus in Hazardous (Classified) Locations
ISBN: 1-55617-696-1
Copyright 1999 by the Instrument Society of America. All rights reserved. Printed in the United
States of America. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means (electronic, mechanical, photocopying, recording, or
otherwise), without the prior written permission of the Publisher.
ISA
67 Alexander Drive
P.O. Box 12277
Research Triangle Park, North Carolina 27709
ANSI/ISA12.01.011999
PREFACE
This preface, as well as all footnotes and annexes, is included for information purposes and is not part of
ANSI/ ISA-12.01.01-1999.
This Standard has been prepared as part of the service of ISA, the international society for measurement
and control, toward a goal of uniformity in the field of instrumentation. To be of real value, this document
should not be static but should be subject to periodic review. Toward this end, the Society welcomes all
comments and criticisms and asks that they be addressed to the Secretary, Standards and Practices
Board; ISA; 67 Alexander Drive; P. O. Box 12277; Research Triangle Park, NC 27709; Telephone (919)
990-9227; Fax (919) 549-8288; E-mail: [email protected].
The ISA Standards and Practices Department is aware of the growing need for attention to the metric
system of units in general, and the International System of Units (SI) in particular, in the preparation of
instrumentation standards. The Department is further aware of the benefits to USA users of ISA standards
of incorporating suitable references to the SI (and the metric system) in their business and professional
dealings with other countries. Toward this end, this Department will endeavor to introduce SI-acceptable
metric units in all new and revised standards, recommended practices, and technical reports to the
greatest extent possible. Standard for Use of the International System of Units (SI): The Modern Metric
System, published by the American Society for Testing & Materials as IEEE/ASTM SI 10-97, and future
revisions, will be the reference guide for definitions, symbols, abbreviations, and conversion factors.
It is the policy of ISA to encourage and welcome the participation of all concerned individuals and interests
in the development of ISA standards, recommended practices, and technical reports. Participation in the
ISA standards-making process by an individual in no way constitutes endorsement by the employer of that
individual, of ISA, or of any of the standards, recommended practices, and technical reports that ISA
develops.
CAUTIONISA ADHERES TO THE POLICY OF THE AMERICAN NATIONAL STANDARDS
INSTITUTE WITH REGARD TO PATENTS. IF ISA IS INFORMED OF AN EXISTING PATENT THAT IS
REQUIRED FOR USE OF THE STANDARD, IT WILL REQUIRE THE OWNER OF THE PATENT TO
EITHER GRANT A ROYALTY-FREE LICENSE FOR USE OF THE PATENT BY USERS COMPLYING
WITH THE STANDARD OR A LICENSE ON REASONABLE TERMS AND CONDITIONS THAT ARE
FREE FROM UNFAIR DISCRIMINATION.
EVEN IF ISA IS UNAWARE OF ANY PATENT COVERING THIS STANDARD, THE USER IS
CAUTIONED THAT IMPLEMENTATION OF THE STANDARD MAY REQUIRE USE OF TECHNIQUES,
PROCESSES, OR MATERIALS COVERED BY PATENT RIGHTS. ISA TAKES NO POSITION ON THE
EXISTENCE OR VALIDITY OF ANY PATENT RIGHTS THAT MAY BE INVOLVED IN IMPLEMENTING
THE STANDARD. ISA IS NOT RESPONSIBLE FOR IDENTIFYING ALL PATENTS THAT MAY
REQUIRE A LICENSE BEFORE IMPLEMENTATION OF THE STANDARD OR FOR INVESTIGATING
THE VALIDITY OR SCOPE OF ANY PATENTS BROUGHT TO ITS ATTENTION. THE USER SHOULD
CAREFULLY INVESTIGATE RELEVANT PATENTS BEFORE USING THE STANDARD FOR THE
USERS INTENDED APPLICATION.
HOWEVER, ISA ASKS THAT ANYONE REVIEWING THIS STANDARD WHO IS AWARE OF ANY
PATENTS THAT MAY IMPACT IMPLEMENTATION OF THE STANDARD NOTIFY THE ISA
STANDARDS AND PRACTICES DEPARTMENT OF THE PATENT AND ITS OWNER.
ANSI/ISA12.01.011999
ADDITIONALLY, THE USE OF THIS STANDARD MAY INVOLVE HAZARDOUS MATERIALS,

OPERATIONS OR EQUIPMENT. THE STANDARD CANNOT ANTICIPATE ALL POSSIBLE
APPLICATIONS OR ADDRESS ALL POSSIBLE SAFETY ISSUES ASSOCIATED WITH USE IN
HAZARDOUS CONDITIONS. THE USER OF THIS STANDARD MUST EXERCISE SOUND
PROFESSIONAL JUDGMENT CONCERNING ITS USE AND APPLICABILITY UNDER THE USERS
PARTICULAR CIRCUMSTANCES. THE USER MUST ALSO CONSIDER THE APPLICABILITY OF
ANY GOVERNMENTAL REGULATORY LIMITATIONS AND ESTABLISHED SAFETY AND HEALTH
PRACTICES BEFORE IMPLEMENTING THIS STANDARD.
The following members of ISA Subcommittee SP12.1 contributed to the development of this document:
NAME
COMPANY
J. Cospolich, Chairman
D. Bishop, Managing Director
D. Ankele
A. Ballard
R. Brodin
U. Dugar
W. Fisk
D. Jagger
J. Kuczka
W. Lawrence*
F. McGowan*
W. Mostia, Jr.
J. Oudar
J. Propst
W. Seaforth
Waldemar S. Nelson and Company, Inc.

Chevron Petroleum Technology Company
Underwriters Laboratories, Inc.
Crouse-Hinds, Division of Cooper Industries
Fisher Controls International, Inc.
Mobil Chemical Company
Intertek Testing Services
Hawke America
Killark
Factory Mutual Research Corporation
Amoco Corp.
ExLoc Corp.
Equilon Enterprises
Woltech Company Inc.
The following members of ISA Committee SP12 contributed to the development of this document:
NAME
COMPANY
F. McGowan, Chairman*
D. Bishop, Managing Director
N. Abbatiello*
D. Ankele*
B. Apel
A. Ballard*
G. Bentinck
K. Boegli
R. Brodin
M. Buettner
R. Buschart
R. Cardinal
C. Casso
M. Coppler
J. Cospolich
Factory Mutual Research Corp.

Eastman Kodak Company
Underwriters Laboratories
MSA Instrument
Crouse-Hinds Division of Cooper Industries, Inc.
E.I. du Pont
Phoenix Contact Inc.
Fisher Controls International, Inc.
Ralston Purina Company
PC & E, Inc.
Bently Nevada Corp.
Schlumberger Oil Field Svcs.
Ametek
Waldemar S. Nelson & Company, Inc.
______
* One vote per company.
J. Costello
S. Czaniecki
T. Dubaniewicz
U. Dugar
A. Engler
T. Feindel
W. Fiske
G. Garcha
E. Geissler
E. Henning
D. Hohenstein
D. Jagger
J. Kuczka
B. Larson
E. Magison
R. Masek
K. McManama*
A. Mobley*
S. Nguyen
E. Olson*
A. Page III
J. Propst
T. Schnaare
W. Shao
J. Thomason
D. Wechsler
ANSI/ISA12.01.011999
Henkel Corp.
Intrinsic Safety Concepts
NIOSH
Mobil Chemical Company
EGS Electrical Group
R. Stahl, Inc.
PCS Engineering
Bartec US Corp.
Bailey, Fischer & Porter
Pepperl + Fuchs Inc.
Hawke America
Killark
Turck Inc.
Consultant
Bailey Controls Company
3M Company
Milltronics
3M Company
MSHA Certification Center
Shell Development Company
Rosemount, Inc.
Canadian Standards Assoc.
OMNI Industrial Systems, Inc.
Union Carbide Corp.
This standard was approved for publication by the ISA Standards and Practices Board on
28 February 1999.
NAME
COMPANY
H. Dammeyer
H. Baumann
D. Bishop
P. Brett
M. Cohen
M. Coppler
W. Holland
A. Iverson
R. Jones
V. Maggioli
T. McAvinew
A. McCauley, Jr.
R. McFarland
R. Reimer
J. Rennie
R. Webb
W. Weidman
The Ohio State University

H. D. Baumann, Inc.
Honeywell, Inc.
Senior Flexonics, Inc.
Ametek, Inc.
Southern Company
Ivy Optiks
Dow Chemical Co.
Feltronics Corp.
Instrumentation & Control Engineering LLC
Chagrin Valley Controls, Inc.
Honeywell, Inc.
Rockwell Automation
Factory Mutual Research Corp.
Altran Corp.
Parsons Energy & Chemicals Group
______
* One vote per company.
ANSI/ISA12.01.011999
J. Weiss
J. Whetstone
M. Widmeyer
R. Wiegle
C. Williams
G. Wood
M. Zielinski
EPRI
National Institute of Standards & Technology
Consultant
CANUS Corp.
Eastman Kodak Co.
Graeme Wood Consulting
Fisher-Rosemount Systems, Inc.
ANSI/ISA12.01.011999
CONTENTS
1 Purpose ............................................................................................................................................ 9
2 Scope ............................................................................................................................................... 9
3 Definitions....................................................................................................................................... 10
4 Area (location) classification........................................................................................................... 23
4.1 North American methods ...................................................................................................... 23
4.2 Additional background information........................................................................................ 25
5 Protection techniques for electrical apparatus in hazardous (classified) locations......................... 29
5.1 Explosion confinement and flame quenching........................................................................ 29
5.2 Isolation from flammable atmospheres ................................................................................. 30
5.3 Energy release limitation....................................................................................................... 32
5.4 Other methods of protection.................................................................................................. 33
5.5 Summary of Types of Protection........................................................................................... 33
6 Wiring methods............................................................................................................................... 35
6.1 Conduit system ..................................................................................................................... 40
6.2 Cable systems....................................................................................................................... 40
6.3 Conduit and cable seals........................................................................................................ 40
6.4 Comparison of the installation systems................................................................................. 43
6.5 Comparisons of wiring methods [see Tables 4a and 4b] ...................................................... 49
7 Grounding and bonding practices................................................................................................... 49
8 Maintenance practices.................................................................................................................... 51
Annex A Acronyms ......................................................................................................................... 53
Annex B References ....................................................................................................................... 57
Annex C Listing of worldwide-codes, guides, and standards.......................................................... 67
Annex D Listing of worldwide installation requirements.................................................................. 77
Figure 1 Vertical conduit seal.......................................................................................................... 35

Figure 2 Conduit drain seal............................................................................................................. 36
Figure 3 Cable seal......................................................................................................................... 36
Figure 4 Conduit drain seal............................................................................................................. 37
Figure 5 Cable system (indirect entry) ............................................................................................ 37
Figure 6 Cable gland (indirect entry)............................................................................................... 38
Figure 7 Cable system (direct entry) ............................................................................................... 38
Figure 8 Cable gland (direct entry) ................................................................................................. 39
Figure 9 Conduit system (direct entry)............................................................................................ 39
ANSI/ISA12.01.011999
Figure 10 Placement of drain seals (Reference API RP 14F, Figure 7, Recommended

Practice for Design and Installation of Electrical Systems for Fixed and Floating
Offshore Petroleum Facilities for Unclassified and Class I, Division 1 and
Division 2 Locations)....................................................................................................... 42
Figure 11 Typical international Group II, Zone 1 conduit system installation.................................. 44
Figure 12 Typical international Group II, Zone 1 cable system installation..................................... 45
Figure 13 Typical United States and Canadian Class I, Division 1 conduit system installation
(Reference API RP 14F, Figure 1, Recommended Practice for Design and
Installation of Electrical Systems for Fixed and Floating Offshore Petroleum
Facilities for Unclassified and Class I, Division 1 and Division 2 Locations) .................. 46
Figure 14 Typical United States and Canadian Class I, Division 1 cable system installation
Figure 15 Typical United States and Canadian Class I, Division 2 conduit/cable system
Table 1 Temperature identification numbers .................................................................................. 28

Table 2 Comparison of classification of flammable vapors and gases (approx.) ............................ 29
Table 3 Summary of Types of Protection (flammable gases or vapors-in-air mixtures) ................ 34
Table 4a Field wiring in United States Class I locations a,b ........................................................... 50
Table 4b Field wiring in United States Class II locations a,b .......................................................... 51
ANSI/ISA12.01.011999
Purpose
This Standard provides definitions and information pertaining to protection techniques, terminology, and
the installation of electrical apparatus in hazardous (classified) locations and provides an introduction and
basic background to the ISA-SP12, Electrical Safety, series of publications and committee activities. It
replaces ISA-S12.1, Definitions and Information Pertaining to Electrical Instruments in Hazardous
Atmospheres, published in 1991.
This document provides a general review of applicable codes and standards, and it should not be used in
lieu of those codes and standards for equipment design, manufacture, installation, maintenance and test
criteria.
Scope
2.1
This Standard provides general guidance for safe design, installation, and maintenance of electrical
apparatus in hazardous (classified) locations using appropriate means to prevent ignition of flammable gases
and vapors, flammable liquids, combustible dusts, or ignitable fibers or flyings.
2.2
This Standard covers only locations made hazardous, or potentially hazardous, due to the presence
of flammable gases or vapors, flammable liquids, combustible dusts, or ignitable fibers or flyings. The
Standard is not necessarily relevant to the hazards posed by pyrophoric materials such as explosives or
propellants containing their own oxidizers.
2.3
This Standard is concerned only with design, manufacture, installation, maintenance, and test criteria
related to arcs, sparks, or hot surfaces produced by electrical apparatus that may cause ignition of flammable
gas or vapor-in-air mixtures, clouds or blankets of combustible dust, or easily ignitable fibers or flyings.
Apparatus should also comply with the applicable ordinary location requirements (e.g., ISA-S82.01 and ISAS82.03).
2.4
This Standard does not cover mechanisms of ignition from external sources, such as static electricity
or lightning. Some apparatus may produce static electricity. The materials of construction of parts in such
apparatus will be an important consideration for application in hazardous locations. The extra precautions
necessary for this are beyond the scope of this Standard.
2.5
This Standard does not consider the effects of installation in corrosive atmospheres and the resulting
deleterious conditions to the original design integrity of the apparatus. The additional precautions necessary
for these conditions are outside the scope of this document.
2.6
This Standard is not an instruction manual for untrained persons. However, it is intended to provide
guidance to those involved with the design, manufacture, installation, and maintenance of apparatus used
in hazardous (classified) locations. It is also intended to promote uniformity of practice among those skilled
in the art. Nothing contained in this Standard is to be construed as a fixed rule without regard to sound
engineering judgment.
2.7
For hazardous location apparatus, atmospheric conditions are generally considered to be
a) an ambient temperature range of -20 C (-4 F) to 40 C (104 F);

b) an oxygen concentration of not greater than 21 percent by volume;
c) a pressure of 86 kPa (12.5 psia) to 108 kPa (15.7 psia); and
ANSI/ISA12.01.011999
10
d) a relative humidity of 5 percent to 95 percent.

NOTE Apparatus specified for atmospheric conditions beyond the average is generally permitted but will be subjected to additional
requirements.
2.8
Specialized industries such as, but not limited to, mining and shipping may be regulated by the specific
authority having jurisdiction. This Standard does not include specific requirements or the rules and
regulations unique to any specific industry.
2.9
Various organizations have developed codes, guides, and standards that have substantial acceptance
by industry and governmental bodies. Codes, guides, and standards useful in the design and installation
of electrical instruments in hazardous (classified) locations are listed in Annex C. These are not considered
to be a part of this Standard except for those specific sections of documents referenced elsewhere in this
Standard.
2.10 Due to the purpose of this Standard, an attempt was made to avoid originality in principles whenever
possible, but rather to utilize definitions, explanations, etc., from accepted publications. As a result, much
of the material, except for minor changes, is directly as published by others. While specific credit is not given
for each reference, all references are included in Annex B.
Definitions
The list is not intended to be all inclusive. Throughout this Standard, reference is made to areas, spaces,
locations, and zones. These terms should be considered interchangeable terms designating a threedimensional space.
3.1
accessible surface:
a surface to which a flammable or combustible mixture has access.
3.2
adequately ventilated area:
an adequately ventilated area is an area that has a ventilation system (natural or artificial) that, as a
minimum, prevents the accumulation of gases or vapors to an explosive level. Most standards and
recommended practices recommend preventing levels in excess of 25 percent of the Lower Flammable
(Explosive) Limit, LFL (LEL).
NOTE Adequate ventilation of an area alone is not an effective means for the prevention of dust explosions.
3.3
AEx:
required marking prefix for apparatus meeting one or more types of protection in Section 505-2(c) for
installation in accordance with Article 505 of the National Electrical Code, NFPA 70: 1999.
3.4
approved:
acceptable to the authority having jurisdiction.
NOTE 1 See AUTHORITY HAVING JURISDICTION.
NOTE 2 In determining the acceptability of installations or procedures, equipment, or material, the AUTHORITY HAVING JURISDICTION
may base acceptance on compliance with appropriate standards. In the absence of such standards, said authority may require
evidence of proper installation, procedure, or use. The AUTHORITY HAVING JURISDICTION may also refer to the listing or labeling
practices of product-testing organizations. These organizations are in a position to determine compliance with appropriate standards
for the current production of listed or labeled items.
11
ANSI/ISA12.01.011999
3.5
arcing device:
an electrical make/break component, that is generally interpreted as capable of producing an arc with
energy sufficient to cause ignition of a specific ignitable mixture.
3.6
associated apparatus:
apparatus in which the circuits are not intrinsically safe themselves but affect the energy in the intrinsically
safe circuits and are relied upon to maintain intrinsic safety. Associated electrical apparatus may be either
a) electrical apparatus that has an alternative type of protection for use in the appropriate hazardous
(classified) location, or
b) electrical apparatus not so protected that shall not be used within a hazardous (classified) location.
See also INTRINSIC SAFETY.
3.7
authority having jurisdiction:
the organization, office, or individual that has the responsibility and authority for approving equipment,
installations, or procedures.
NOTE The term AUTHORITY HAVING JURISDICTION is used in a broad manner since jurisdiction and approval agencies vary, as do
their responsibilities. Where public safety is primary, the authority having jurisdiction may be a federal, state/provincial, local, other
regional department, or an individual such as an inspector from a labor or health department, electrical inspector, or others having
statutory authority. An insurance inspection agency, rating bureau, or other insurance company representative may be the authority
having jurisdiction. An owner or his designated agent may also assume the role. At government-owned installations, the
commanding officer, departmental official, or designated agent may be the authority having jurisdiction.
3.8
automatic:
self-acting, operating by its own mechanism when actuated by some impersonal influence, as for example,
a change in current strength, pressure, temperature, or mechanical configuration.
3.9
bonding:
the permanent joining of metallic parts to form an electrically conductive path that will ensure electrical
continuity and the capacity to conduct safely any current likely to be imposed.
3.10 cable entry (cable gland):
a device permitting the introduction of an electric cable into an electrical apparatus.
3.11 certified:
generic term referring to apparatus that has been evaluated by a recognized testing agency and confirmed
to be in compliance with the applicable standard(s).
NOTE Some agencies use the terms approved, listed, or labeled apparatus to indicate compliance with the applicable standard.
3.12 Class I location:

a location in which flammable gases or vapors are or may be present in the air in quantities sufficient to
produce explosive or ignitable mixtures. See 3.116, 3.118, & 3.120 for definitions of Class I, Zones 0, 1, &
2.
3.13 Class I, Division 1 location:
a location (1) in which ignitable concentrations of flammable gases or vapors can exist under normal
operating conditions; (2) in which ignitable concentrations of such gases or vapors may exist frequently
because of repair or maintenance operations or because of leakage; or (3) in which breakdown or faulty
operation of equipment or processes might release ignitable concentrations of flammable gases or vapors
and might also cause simultaneous failure of electrical equipment that could act as a source of ignition.
ANSI/ISA12.01.011999
12
3.14 Class I, Division 2 location:

a location (1) in which volatile flammable liquids or flammable gases are handled, processed, or used, but
in which the liquids, vapors, or gases will normally be confined within closed containers or closed systems
from which they can escape only in case of accidental rupture or breakdown of such containers or
systems, or in case of abnormal operation of equipment; or (2) in which ignitable concentrations of gases
or vapors are normally prevented by positive mechanical ventilation and might become hazardous through
failure or abnormal operation of the ventilating equipment; or (3) that is adjacent to a Class I, Division 1
location and to which ignitable concentrations of gases or vapors might occasionally be communicated
unless such communication is prevented by adequate positive-pressure ventilation from a source of clean
air and effective safeguards against ventilation failure are provided.
3.15 Class II location:
a location that is hazardous because of the presence of combustible dust.
3.16 Class II, Division 1 location:
a location (1) in which combustible dust is in the air under normal operating conditions in quantities
sufficient to produce explosive or ignitable mixtures; or (2) in which mechanical failure or abnormal
operation of machinery or equipment might cause such explosive or ignitable mixtures to be produced and
might also provide a source of ignition through simultaneous failure of electrical equipment, operation of
protection devices, or from other causes; or (3) in which combustible dusts of an electrically conductive
nature may be present in hazardous quantities.
3.17 Class II, Division 2 location:
a location in which combustible dust is not normally in the air in quantities sufficient to produce explosive or
ignitable mixtures and dust accumulations are normally insufficient to interfere with the normal operation of
electrical equipment or other apparatus, but combustible dust may be in suspension in the air as a result of
infrequent malfunctioning of handling or processing equipment and where combustible dust accumulations
on, in, or in the vicinity of the electrical equipment may be sufficient to interfere with the safe dissipation of
heat from electrical equipment or may be ignitable by abnormal operation or failure of electrical equipment.
3.18 Class III location:
a location that is hazardous because of the presence of easily ignitable fibers or flyings but in which such
fibers or flyings are not likely to be in suspension in the air in quantities sufficient to produce ignitable
mixtures.
3.19 Class III, Division 1 location:
a location in which easily ignitable fibers or materials producing combustible flyings are handled,
manufactured, or used.
3.20 Class III, Division 2 location:
a location in which easily ignitable fibers are stored or handled (except in the process of manufacture).
3.21 code of practice:
a term referring to a document that describes basic safety features and methods of protection and
recommends, e.g., the selection, installation, inspection, and maintenance procedures that should be
followed to ensure the safe use of electrical apparatus.
3.22 continuous dilution:
the technique of supplying a protective gas flow continuously to an enclosure containing an internal
potential source of flammable gas or vapor for the purpose of diluting any flammable gas or vapor that
could be present to a level below its LFL/LEL. Refer to 5.2.2.
13
ANSI/ISA12.01.011999
3.23 control drawing:

a drawing or other document provided by the manufacturer of the intrinsically safe or associated apparatus
that details the allowed interconnections between the intrinsically safe and associated apparatus.
3.24 degree of protection (IP):
a system of rating standard levels of protection provided by apparatus for the protection of persons against
contact with live or moving parts inside the apparatus, as well as the protection provided by apparatus
against ingress of solids and/or liquids. This type of protection classification is in addition to (and not an
alternative to) the types of protection necessary to ensure protection against ignition in hazardous
(classified) locations. Definitions are found in IEC Publication 60529.
NOTE See also ENCLOSURE TYPE.
3.25 dust, combustible:

any finely divided solid material 420 microns or less in diameter (i.e., material passing a U.S. No. 40
sieve) that presents a fire or explosion hazard when dispersed.
3.26 dust-ignitionproof:
a term used to describe an enclosure that will exclude dust and that, when installed in accordance with the
original design intent, will not permit arcs, sparks, or heat otherwise generated or liberated inside the
enclosure to cause ignition of exterior accumulations or atmosphere suspensions of a specified dust in the
vicinity of the enclosure.
3.27 dust layer, combustible:
any surface accumulation of combustible dust that is thick enough to propagate flame or will degrade and
ignite.
3.28 dust-protected enclosure:
a term describing an enclosure in which the ingress of dust is not totally prevented, but dust does not enter
in sufficient quantity to interfere with the safe operation of the equipment or accumulate in a position within
the enclosure where it is possible to cause an ignition hazard.
3.29 dusttight:
an enclosure so constructed that dust will not enter the enclosing case under specified test conditions.
3.30 EEx:
designation of explosion-protected electrical apparatus complying with harmonized CENELEC Standards.
3.31 electrical apparatus:
items applied as a whole or in part for the utilization of electrical energy. These include, among others,
equipment for the generation, transmission, distribution, storage, measurement, regulation, conversion,
and consumption of electrical energy and items for telecommunication.
3.32 enclosure type:
a North American system of rating standard levels of protection provided to electrical apparatus by
enclosures for 1) the protection of persons against contact with live or moving parts inside the enclosure,
2) the protection provided by the enclosure against ingress of solids and/or liquids, 3) the protection
provided by the enclosure against the deleterious effects of corrosion, and 4) the protection provided by
the enclosure against damage due to the formation of external ice. This enclosure type is in addition to
(and not an alternative to) the types of protection necessary to ensure protection against ignition in
hazardous (classified) locations. Definitions are found in UL 50 or NEMA 250.
NOTE See also DEGREE OF PROTECTION.
ANSI/ISA12.01.011999
14
3.33 encapsulation:
a type of protection in which the parts that could ignite an explosive atmosphere by either sparking or
heating are enclosed in an encapsulant in such a way that this explosive atmosphere cannot be ignited.
This type of protection is referred to as m.
3.34 energized:
electrically connected to a source of potential difference.
3.35 entity concept:
a concept that allows interconnection of intrinsically safe apparatus to associated apparatus not
specifically examined in such a combination. The criteria for interconnection is that the voltage (Vmax)
and current (Imax) which intrinsically safe apparatus can receive and remain intrinsically safe, considering
faults, must be equal to or greater than the voltage (Voc or Vt) and current (Isc or It) levels which can be
delivered by the associated apparatus, considering faults and applicable factors. In addition, the maximum
unprotected capacitance (Ci) and inductance (Li) of the intrinsically safe apparatus, including
interconnecting wiring, must be equal to or less than the capacitance (Ca) and inductance (La) that can
safely be connected to the associated apparatus. If these criteria are met, then the combination may be
connected without compromising intrinsic safety. For additional information refer to ISA RP12.6.
3.36 entry, direct:
a method of connection of an electrical apparatus to the external circuits by means of the connecting
facilities inside the main enclosure or in a terminal compartment having a free opening to the main
enclosure. (IEV 426-04-07)
3.37 entry, indirect:
a method of connection of an electrical apparatus to the electrical circuits by means of a terminal box or a
plug and socket connection which is external to the main enclosure. (IEV 426-04-08)
3.38 Ex:
designation of explosion-protected electrical apparatus
3.39 Ex component:
part of electrical apparatus for explosive atmospheres which is not to be used alone in such atmospheres
and which requires additional evaluation of any electrical apparatus with which it is used.
3.40 Ex Scheme:
an international system of certification for explosion-protected electrical apparatus administered by the
IECEE and described by IECEE-04. The eventual goal of this scheme is that a manufacturer of hazardous
location electrical apparatus would be able to obtain a single Ex Certificate of Conformity from one
Certification Laboratory and provide that product in any participating country without legal or technical
obstacle and without the need to get it recertified locally.
3.41 explosionproof:
a term used to describe an enclosure that is capable of withstanding an explosion of a specified gas or
vapor that may occur within it and of preventing the ignition of a specified gas or vapor surrounding the
enclosure by sparks, flashes, or explosion of the gas or vapor within, and that operates at such an external
temperature that a surrounding flammable atmosphere will not be ignited thereby. (NEC)
NOTE See also FLAMEPROOF ENCLOSURE.
3.42 explosive atmosphere:

a mixture with air, under atmospheric conditions, of flammable substances in the form of gas, vapor, mist,
or dust in which, after ignition, combustion spreads throughout the unconsumed mixture.
15
ANSI/ISA12.01.011999
NOTE See also HAZARDOUS (CLASSIFIED) LOCATION.
3.43 fault (as applicable to intrinsically safe systems):

a defect or electrical breakdown of any component, spacing, or insulation that alone or in combination with
other defects or breakdowns may adversely affect the electrical or thermal characteristics of the
intrinsically safe system. If a defect or breakdown leads to defects or breakdowns in other components,
the primary and subsequent defects and breakdowns are considered to be a single fault. Certain
components may be considered not subject to fault when analyses or tests for intrinsic safety are made.
See also PROTECTIVE COMPONENT.
3.44 fibers and flyings:
these are materials not normally in suspension in air; and are of larger particle size than dusts. Fibers and
flyings include materials such as cotton linters, sawdust, textile fibers, and other large particles that are
usually more a fire hazard than an explosion hazard.
3.45 flameproof:
a type of protection of electrical apparatus in which an enclosure will withstand an internal explosion of a
flammable mixture which has penetrated into the interior, without suffering damage and without causing
ignition, through any joints or structural openings in the enclosure, of an external explosive atmosphere
consisting of one or more of the gases or vapors for which it is designed. This type of protection is referred
to as d.
NOTE See also EXPLOSIONPROOF APPARATUS.
3.46 flammable (explosive) limits:

the flammable (explosive) limits of a gas or vapor are the lower (LFL/LEL) and upper (UFL/UEL) flammable
(explosive) limit percentages by volume of concentration of gas in a gas-air mixture that will form an
ignitable mixture.
NOTE 1 For additional information refer to NFPA 325 and IEC 60079-20.
NOTE 2 The term explosive as it relates to atmospheres and mixtures is in the process of being replaced with the more technically
correct term flammable throughout many national and international standards. This document, however, continues to use the term
explosive in many of the definitions that are repeated here as those definitions have been derived from documents that have yet to be
updated.
3.47 flammable liquid:

any liquid having a flash point below 37.8 C (100 F) and having a vapor pressure not exceeding 275 kPa
(40 psia) at 37.8 C(100 F).
NOTE For additional information, refer to NFPA 325.
3.48 flammable gas or vapor:

a gas or vapor which, when mixed with air in certain proportions, will form an explosive gas atmosphere.
3.49 flash point:
the minimum temperature at which a liquid gives off vapor in sufficient concentration to form an ignitable
mixture with air near the surface of the liquid, as specified by test.
NOTE For additional information, refer to NFPA 325.
3.50 ground:
a conducting connection, whether intentional or accidental, between an electrical circuit or apparatus and
the earth, or to some conducting body that serves in place of the earth.
ANSI/ISA12.01.011999
16
3.51 grounded (earthed):

connected to earth or to some conducting body that serves in place of earth.
3.52 group:
a classification of combustible materials.
NOTE Refer to Clause 4 for additional information.
3.53 hazardous (classified) location:

a location in which fire or explosion hazards may exist due to an explosive atmosphere of flammable gases
or vapors, flammable liquids, combustible dust, or easily ignitable fibers or flyings.
NOTE See also EXPLOSIVE ATMOSPHERE.
3.54 hermetically sealed device:

a device that is sealed against the entrance of an external atmosphere and in which the seal is made by
fusion, e.g., soldering, brazing, welding or the fusion of glass to metal.
3.55 temperature apparatus:
as specified by NEC, Article 501-5(a)(1), the term high temperature apparatus is to be interpreted as
apparatus in which the maximum operating temperature (including ambient temperature effect) exceeds
80 percent of the autoignition temperature in degrees Celsius (C) of the gas or vapor involved.
3.56 identified (as applied to equipment):
recognizable as suitable for the specific purpose, function, use, environment, application, etc., where
described in a particular requirement, e.g. NEC.
NOTE Suitability of equipment for a specific purpose, environment, or application may be determined by a qualified testing
laboratory, inspection agency, or other organization concerned with product evaluation. Such identification may include labeling or
listing. For additional information see labeled and listed.
3.57 ignition (autoignition) temperature (AIT):

the minimum temperature required to initiate or cause self-sustained combustion of a solid, liquid, or gas
independently of the heating or heating elements.
NOTE 1 For additional information refer to NFPA 325.
NOTE 2 A distinction is made between ignition temperature and flash point. See FLASH POINT.
3.58 ignition capable:

apparatus or wiring that under normal conditions, or under specified abnormal conditions, can release
sufficient electrical or thermal energy to cause ignition of a specific explosive atmosphere.
3.59 increased safety:
a type of protection applied to electrical apparatus that does not produce arcs or sparks in normal service
and under specified abnormal conditions, in which additional measures are applied so as to give increased
security against the possibility of excessive temperatures and of the occurrence of arcs and sparks. This
type of protection is referred to as e.
3.60 internal wiring:
wiring and electrical connections that are made within apparatus by the manufacturer. Within racks or
panels, interconnections between separate pieces of apparatus made in accordance with detailed
instructions from the apparatus manufacturer are also considered to be internal wiring.
17
ANSI/ISA12.01.011999
3.61 intrinsic safety:

a type of protection in which a portion of the electrical system contains only intrinsically safe apparatus,
circuits, and wiring that is incapable of causing ignition in the surrounding atmosphere. No single device or
wiring is intrinsically safe by itself (except for battery-operated, self-contained apparatus such as portable
pagers, transceivers, gas detectors, etc., which are specifically designed as intrinsically safe selfcontained devices) but is intrinsically safe only when employed in a properly designed intrinsically safe
system. This type of protection is referred to as i.
NOTE See also ASSOCIATED APPARATUS.
3.62 intrinsic safety barrier:

a component containing a network designed to limit the energy (voltage and current) available to the
protected circuit in the hazardous (classified) location under specified fault conditions.
3.63 intrinsically safe circuit:
a circuit in which any spark or thermal effect, produced either normally or in specified fault conditions, is
incapable, in the specified test conditions, of causing ignition of a given explosive atmosphere.
3.64 intrinsically safe electrical apparatus:
electrical apparatus in which all the circuits are intrinsically safe circuits.
3.65 intrinsic safety ground bus:
a grounding system that has a dedicated conductor separate from the power system so that ground
currents will not normally flow and that is reliably connected to a ground electrode.
NOTE For further information, refer to Article 504 of NEC, or Section 10 of CSA C22.1, or ISA RP 12.6.
3.66 intrinsically safe system:

an assembly of interconnected intrinsically safe apparatus, associated apparatus, other apparatus, and
interconnecting cables in which those parts of the system that may be used in hazardous (classified)
locations are intrinsically safe circuits.
3.67 labeled:
equipment or materials with a label, symbol, or other identifying mark of an organization that is acceptable
to the authority having jurisdiction and concerned with product evaluation that maintains periodic
inspection of production of labeled equipment or materials and by whose labeling the manufacturer
indicates compliance with appropriate standards or performance in a specified manner.
NOTE Some agencies use the term approved, listed, or certified to indicate compliance with the applicable standard.
3.68 liquid, combustible:

a liquid having a flash point at or above 37.8C (100F). Combustible liquids are subdivided as follows:
a) Class II liquids include those having flash points at or above 37.8C (100F) and below 60C (140F).
b) Class IIIA liquids include those having flash points at or above 60C (140F) and below 93C (200F).
c) Class IIIB liquids include those having flash points at or above 93C (200F).
NOTE For additional information, refer to NFPA 325. It should also be noted that these classes have no relation to the hazardous
location classes.
ANSI/ISA12.01.011999
18
3.69 listed:
equipment or materials included in a list published by an organization acceptable to the authority having
jurisdiction and concerned with product evaluation, that maintains periodic inspection of production of
listed equipment or materials, and whose listing states either that the equipment or material meets
appropriate designated standards or has been tested and found suitable for use in a specified manner.
NOTE The means for identifying listed equipment may vary for each organization concerned with product evaluation, some of
which do not recognize equipment as listed unless it is also labeled. The authority having jurisdiction should utilize the system
employed by the listing organization to identify a listed product.
3.70 lower explosive limit (LEL):

refer to FLAMMABLE (EXPLOSIVE) LIMITS.
3.71 lower flammable limit (LFL):
3.72 maintenance, corrective:
any maintenance activity that is not normal in the operation of equipment and requires access to the
equipments interior. Such activities are expected to be performed by a qualified person. Such activities
typically include locating causes of faulty performance, replacement of defective components, adjustment
of internal controls, and the like.
3.73 maintenance, operational:
any maintenance activity, excluding corrective maintenance, intended to be performed by the operator and
required in order for the equipment to serve its intended purpose. Such activities typically include the
correcting of zero on a panel instrument, changing charts, record keeping, adding ink, and the like.
3.74 make/break component:
components having contacts that can interrupt a circuit (even if the interruption is transient in nature).
Examples of make/break components are relays, circuit breakers, servo potentiometers, adjustable
resistors, switches, connectors, and motor brushes.
3.75 maximum surface temperature:
the highest temperature attained by a surface accessible to flammable gases, vapors, or combustible
dusts under conditions of operation within the ratings of the apparatus (including specified abnormal
conditions).
3.76 minimum cloud ignition temperature:
the minimum temperature at which a combustible dust atmosphere will autoignite and propagate an
explosion.
3.77 minimum dust layer ignition temperature:
the minimum temperature of a surface that will ignite a dust on it after a long time (theoretically, until
infinity). In most dusts, free moisture has been vaporized before ignition.
3.78 minimum explosive (dust) concentration:
the minimum concentration of a dust cloud that, when ignited, will propagate a flame away from the source
of ignition.
3.79 minimum ignition energy (MIE):
the smallest amount of energy that can ignite the most easily ignitable mixture of a specific gas or vapor-inair mixture or dust-in-air mixture.
19
ANSI/ISA12.01.011999
3.80 maximum experimental safe gap (MESG):

the maximum clearance between two parallel metal surfaces that has been found, under specified test
conditions, to prevent an explosion in a test chamber from being propagated to a secondary chamber
containing the same gas or vapor at the same concentration.
3.81 minimum igniting current ratio (MIC Ratio):
the ratio derived by dividing the minimum current required from an inductive spark discharge to ignite the
most easily ignitable mixture of a gas or vapor by the minimum current required from an inductive spark
discharge to ignite methane under the same test conditions.
NOTE For additional information, refer to IEC 60079-3.
3.82 nonautomatic:
non-self-acting requiring personal intervention for control. As applied to an electric controller,
nonautomatic control does not necessarily imply a manual controller, but only that personal intervention is
necessary.
3.83 nonhazardous (unclassified) location:
a location in which fire or explosion hazards are not expected to exist specifically due to the presence of
flammable gases or vapors, flammable liquids, combustible dusts, or ignitable fibers or flyings. Such a
location may also be referred to as a safe area.
3.84 nonincendive circuit:
a circuit, other than field wiring, in which any arc or thermal effect produced, under intended operating
conditions of the equipment, is not capable, under specified test conditions, of igniting the flammable
gas-, vapor-, or dust-air mixture. See also 3.87, NONINCENDIVE FIELD WIRING.
3.85 nonincendive component:
a component having contacts for making or breaking an ignition-capable circuit and in which the contacting
mechanism is constructed so that the component is incapable of igniting the specified explosive
atmosphere. The housing of a nonincendive component is not intended to (1) exclude the flammable
atmosphere or (2) contain an explosion. This type of protection is referred to as nC.
3.86 nonincendive equipment:
equipment having electrical/electronic circuitry and components that are incapable, under normal
conditions, of causing ignition of the flammable gas-, vapor-, or dust-air mixture due to arcing or thermal
effect. This type of protection is referred to as nA, nC, or nR.
3.87 nonincendive field wiring:
wiring that enters or leaves an equipment enclosure and, under normal operating conditions of the
equipment, is not capable, due to arcing or thermal effects, of igniting the flammable gas-, vapor-, or dustair mixture. Normal operation includes opening, shorting, or grounding the field wiring. See also 3.84,
NONINCENDIVE CIRCUIT.
3.88 normal conditions:
equipment is generally considered to be under normal conditions when it conforms electrically and
mechanically with its design specifications and is used within the limits specified by the manufacturer.
3.89 oil-immersion:
type of protection in which the electrical apparatus or parts of the electrical apparatus are immersed in a
protective liquid in such a way that an explosive atmosphere which may be above the liquid or outside the
enclosure cannot be ignited. This type of protection is referred to as o.
ANSI/ISA12.01.011999
20
3.90 powder filling:

a type of protection in which the parts capable of igniting an explosive atmosphere are fixed in position and
completely surrounded by filling material to prevent the ignition of an external explosive atmosphere. This
type of protection is referred to as q.
NOTE This type of protection may not prevent the surrounding explosive atmosphere from penetrating into the apparatus and Ex
components and being ignited by the circuits. However, due to the small free volumes in the filling material and due to the quenching
of a flame that may propagate through the paths in the filling material, an external explosion is prevented.
3.91 pressurization:
the technique of guarding against the ingress of the external atmosphere into an enclosure by maintaining
a PROTECTIVE GAS therein at a pressure above that of the external atmosphere. This type of protection is
referred to as p.
3.92 pressurization, Type X:
a method of reducing the classification within an enclosure from Division 1/Zone 1 to nonhazardous
(unclassified). See 5.2.1.
3.93 pressurization, Type Y:
a method of reducing the classification within an enclosure from Division 1/Zone 1 to Division 2/Zone 2.
See 5.2.1.
3.94 pressurization, Type Z:
a method of reducing the classification within an enclosure from Division 2/Zone 2 to nonhazardous
(unclassified). See 5.2.1.
3.95 protection, type of:
the specific measures applied to electrical apparatus to avoid ignition of a surrounding explosive
atmosphere. Examples are e and n.
3.96 protective component (as applied to intrinsic safety):
a component that is so unlikely to become defective in a manner that will lower the intrinsic safety of the
circuit that it may be considered not subject to fault when analyses or tests for intrinsic safety are made.
3.97 protective gas:
the gas used for pressurization or for the dilution of flammable gases to a level well below their lower
explosive limit, usually below 25 percent LFL/LEL. The protective gas may be air, nitrogen, other
nonflammable gas, or a mixture of such gases.
3.98 purging:
in a pressurized enclosure, the operation of passing a quantity of PROTECTIVE GAS through the enclosure
and ducts, so that the concentration of the explosive gas atmosphere is brought to a safe level.
3.99 qualified person:
one familiar with the construction and operation of the equipment and the hazards involved.
3.100 restricted breathing:
a protection technique in which the tightness of an enclosure is assured so that short-term presence of a
flammable gas or vapor cloud around the enclosure will not cause the concentration inside the enclosure
to reach the LFL/LEL because of breathing or diffusion. This type of protection is referred to as nR.
3.101 safe area:
refer to NONHAZARDOUS (UNCLASSIFIED) LOCATION.
21
ANSI/ISA12.01.011999
3.102 seal, cable, explosionproof:

a cable termination fitting filled with compound and designed to contain an explosion in the enclosure to
which it is attached or to minimize passage of flammable gases or vapors from one location to another. A
conduit seal in combination with a cable termination fitting may also be used as a cable seal.
3.103 seal, conduit, explosionproof:
a sealing fitting, filled with a poured potting compound, designed to contain an explosion in the enclosure
to which it is attached and to minimize passage of flammable gases or vapors from one location to another.
3.104 seal, factory:
a construction where components capable of initiating an internal explosion due to arcing, sparking, or
thermal effects under normal conditions are isolated from the wiring system by means of factory installed
flameproof seal or joint for the purpose of eliminating the need for an external, field-installed conduit seal
and, in some cases, a field-installed cable seal.
3.105 sealed device:
a device so constructed that it cannot be opened during normal operational conditions or operational
maintenance; it has a free internal volume less than 100 cubic centimeters (6.1 cubic inches) and is sealed
to restrict entry of an external atmosphere. This type of protection is referred to as nC.
3.106 simple apparatus (as applied to intrinsic safety):
a device that will not generate or store more than 1.2 V, 0.1 A, 25 mW, or 20 J. Examples are: switches,
thermocouples, light-emitting diodes, and resistance temperature detectors (RTDs).
3.107 source of release:
a point from which flammable gases or vapors, flammable liquid, combustible dusts, or ignitable fibers or
flyings may be released into the atmosphere.
3.108 special protection:
a protection technique other than those that have been standardized. This type of protection is referred to
by IEC 60079-0 as s.
3.109 temperature, ambient:
the temperature of air or other media where electrical apparatus is to be used.
3.110 temperature identification number (T Code/Temperature Class):
a system of classification by which one of 14 temperature identification numbers (for zones, six
temperature classes) is allocated to apparatus. The temperature identification number represents the
maximum surface temperature of any part of the apparatus that may come in contact with the flammable
gas or vapor mixture. See Table 1.
3.111 type of protection:
refer to PROTECTION, TYPE OF.
3.112 upper explosive limit (UEL):
3.113 upper flammable limit (UFL):
3.114 zone:
a method of specifying the probability that a location is made hazardous by the presence, or potential
presence, of flammable concentrations of gases and vapors, or combustible mixtures of dusts.
ANSI/ISA12.01.011999
22
3.115 Zone 0 (IEC):

an area in which an explosive gas atmosphere is present continuously or for long periods. (IEV 426-03-03,
modified).
3.116 Zone 0, Class I (NEC):
a Class I, Zone 0 location is a location (1) in which ignitable concentrations of flammable gases or vapors
are present continuously; or (2) in which ignitable concentrations of flammable gases or vapors are present
for long periods of time. (NEC Section 505-9(a))
3.117 Zone 1 (IEC):
an area in which an explosive gas atmosphere is likely to occur in normal operation. (IEV 426-03-04)
are likely to exist under normal operating conditions; or (2) in which ignitable concentrations of flammable
gases or vapors may exist frequently because of repair or maintenance operations or because of leakage;
or (3) in which equipment is operated or processes are carried on, of such a nature that equipment
breakdown or faulty operations could result in the release of ignitable concentrations of flammable gases
or vapors and also cause simultaneous failure of electrical equipment in a mode to cause the electrical
equipment to become a source of ignition; or (4) that is adjacent to a Class I, Zone 0 location from which
ignitable concentrations of vapors could be communicated, unless communication is prevented by
adequate positive-pressure ventilation from a source of clean air and effective safeguards against
ventilation failure are provided. (NEC Article 505-9(b))
3.119 Zone 2 (IEC):
an area in which an explosive gas atmosphere is not likely to occur in normal operation and, if it does
occur, is likely to do so only infrequently and will exist for a short period only. (IEV 426-03-05, modified)
are not likely to occur in normal operation, and if they do occur, will exist only for a short period; or (2) in
which volatile flammable liquids, flammable gases, or flammable vapors are handled, processed, or used,
but in which the liquids, gases, or vapors normally are confined within closed containers or closed systems
from which they can escape only as a result of accidental rupture or breakdown of the containers or
system, or as the result of the abnormal operation of the equipment with which the liquids or gases are
handled, processed, or used; or (3) in which ignitable concentrations of flammable gases or vapors
normally are prevented by positive mechanical ventilation, but which may become hazardous as the result
of failure or abnormal operation of the ventilation equipment; or (4) that is adjacent to a Class I, Zone 1
location from which ignitable concentrations of flammable gases or vapors could be communicated, unless
such communication is prevented by adequate positive-pressure ventilation from a source of clean air, and
effective safeguards against ventilation failure are provided. (NEC Section 505-9(c))
3.121 Zone 20 (IEC):
an area in which combustible dust, as a cloud, is present continuously or frequently, during normal
operation, in sufficient quantity to be capable of producing an explosible concentration of combustible dust
in mixture with air and/or where layers of dust of uncontrollable and excessive thickness can be formed.
This can be the case inside dust containment where dust can form explosible mixtures frequently or for
long periods of time. This occurs typically inside equipment. (IEC 1241-3 - 2.11)
3.122 Zone 21 (IEC):
an area not classified as Zone 20 in which combustible dust, as a cloud, is likely to occur during normal
operation, in sufficient quantity to be capable of producing an explosible concentration of combustible dust
in mixture with air. This zone can include, among others, areas in the immediate vicinity of powder filling or
23
ANSI/ISA12.01.011999
emptying points and areas where dust layers occur and are likely in normal operation to give rise to an
explosible concentration of combustible dust in mixture with air. (IEC 1241-3 - 2.12)
3.123 Zone 22 (IEC):
an area not classified as Zone 21 in which combustible dust, as a cloud, can occur infrequently, and persist
only for a short period, or in which accumulations or layers of combustible dust can give rise to an
explosive concentration of combustible dust in mixture with air. This zone can include, among others,
areas in the vicinity of equipment containing dust, and in which dust can escape from leaks and form
deposits (e.g. milling rooms in which dust can escape from the mills and then settle). (IEC 1241-3 - 2.13)
Area (location) classification
Area classification schemes should specify the kind of flammable material that may be present and the
probability that it will be present in ignitable concentrations. Area classification schemes and systems of
material classification have been developed to provide a succinct description of the hazard so that
appropriate safeguards may be selected. The type of protection technique selected and the level of
protection it must provide depend upon the potential hazard caused by using electrical apparatus in a
location in which a combustible, flammable, or ignitable substance may be present.
4.1
North American methods
In the United States, the area classification definitions are stated in Articles 500 and 505 of the National
Electrical Code, (NEC) NFPA 70. In Canada, similar definitions are given in the Canadian Electrical Code
(CEC), Part 1, Section 18 and Annex J18 (CSA C22.1).
Various organizations have developed numerous guides and standards that have substantial acceptance
by industry and governmental bodies for area classification. Refer to Annex C.
Area classification definitions used in the United States and Canada include the following:
a) CLASS the generic form of the flammable materials in the atmosphere, which may include gas or
vapor, dusts, or easily ignitable fibers or flyings (see Clause 3 for detailed definitions);
b) DIVISION (or ZONE) an indication of the probability of the presence of the flammable material in
ignitable concentration (see Clause 3 for detailed definitions); and
c) GROUP the exact nature of the flammable material (see 4.1.1 & 4.1.2).
4.1.1
Groups (NEC Article 500 / CEC Annex J18)
The United States and Canadian Electrical Codes recognize seven groups: Groups A, B, C, D, E, F, and G.
Groups A, B, C, and D apply to Class I locations; Groups E, F, and G apply to Class II Locations. In NEC
these groups are defined as:
Group A - Acetylene
Group B - Flammable gas, flammable liquid-produced vapor, or combustible liquid-produced vapor mixed
with air that may burn or explode, having either a MAXIMUM EXPERIMENTAL SAFE GAP (MESG) less than or
equal to 0.45 mm or a MINIMUM IGNITING CURRENT RATIO (MIC RATIO) less than 0.4.
NOTE A typical Class I, Group B material is hydrogen.
Group C - Flammable gas, flammable liquid-produced vapor, or combustible liquid-produced vapor mixed
with air that may burn or explode, having either MAXIMUM EXPERIMENTAL SAFE GAP (MESG) values greater
ANSI/ISA12.01.011999
24
than 0.45 mm and less than or equal to 0.75 mm or a MINIMUM IGNITING CURRENT RATIO (MIC RATIO) greater
than or equal to 0.4 and less than or equal to 0.80.
NOTE A typical Class I, Group C material is ethylene.
Group D - Flammable gas, flammable liquid-produced vapor, or combustible liquid-produced vapor mixed
with air that may burn or explode, having a MAXIMUM EXPERIMENTAL SAFE GAP (MESG) greater than 0.75
mm or a MINIMUM IGNITING CURRENT RATIO (MIC RATIO) greater than 0.80, or gases or vapors of equivalent
hazard.
NOTE A typical Class I, Group D material is propane.
Additional information on group classification can be found in NFPA 497, Classification of Flammable
Liquids, Gases or Vapors and of Hazardous (Classified) Locations for Electrical Installations in Chemical
Process Areas.
Group E Atmospheres containing combustible metal dusts, including aluminum, magnesium, and their
commercial alloys, or other combustible dusts whose particle size, abrasiveness, and conductivity present
similar hazards in the use of electrical equipment.
Group F Atmospheres containing combustible carbonaceous dusts that have more than 8 percent total
entrapped volatiles (see ASTM D3175-89 for coal and coke dusts) or that have been sensitized by other
materials so that they present an explosion hazard. Coal, carbon black, charcoal, and coke dusts are
examples of carbonaceous dusts.
Group G Atmospheres containing other combustible dusts, including flour, grain, wood flour, plastic, and
chemicals.
Additional information on Group Classification can be found in NFPA 499 Classification of Combustible
Dusts and of Hazardous (Classified) Locations for Electrical Installations in Chemical Process Areas.
4.1.2
Groups (NEC Article 505/CSA C22.1 Section 18/IEC 60079-12/prEN 60079-12)
These groups are defined as:

Group IIC - Flammable gas, flammable liquid-produced vapor, or combustible liquid-produced vapor mixed
with air that may burn or explode, having either MAXIMUM EXPERIMENTAL SAFE GAP (MESG) less than or
equal to 0.5 mm or MINIMUM IGNITING CURRENT RATIO (MIC RATIO) less than 0.45, or gases or vapors of
equivalent hazard.
NOTE 1 This group is similar to a combination of Groups A & B as described in 4.1.1, although the MESG and MIC RATIO numbers
are slightly different.
NOTE 2 Typical gases include acetylene, carbon disulfide, hydrogen, and gases or vapors of equivalent hazard.
Group IIB - Flammable gas, flammable liquid-produced vapor, or combustible liquid-produced vapor mixed
with air that may burn or explode, having either MAXIMUM EXPERIMENTAL SAFE GAP (MESG) values greater
than 0.5 mm and less than or equal to 0.9 mm or MINIMUM IGNITING CURRENT RATIO (MIC RATIO) greater
than or equal to 0.45 and less than or equal to 0.80, or gases or vapors of equivalent hazard.
NOTE 1 This group is similar to Group C as described in 4.1.1, although the MESG and MIC RATIO numbers are slightly different.
NOTE 2 Typical gases include ethylene and gases or vapors of equivalent hazard.
25
ANSI/ISA12.01.011999
Group IIA - Flammable gas, flammable liquid-produced vapor, or combustible liquid-produced vapor mixed
with air that may burn or explode, having MAXIMUM EXPERIMENTAL SAFE GAP(MESG) greater than 0.9 mm or
MINIMUM IGNITING CURRENT RATIO (MIC RATIO) greater than 0.80, or gases or vapors of equivalent hazard.
NOTE 1 This group is similar to Group D as described in 4.1.1, although the MESG number is slightly different.
NOTE 2 Typical gases include propane and gases or vapors of equivalent hazard.
Additional information on group classification can be found in IEC 60079-12 & IEC 60079-20.
4.2
4.2.1
Additional background information

History
Historically, the topic of Hazardous (Classified) Locations first appeared in the National Electrical Code
(NEC) in 1923, when a new article entitled Extra-Hazardous Locations was accepted. This article
addressed rooms or compartments in which highly flammable gases, liquids, mixtures or other substances
were manufactured, used, or stored. In 1931, Classifications consisting of Class I, Class II, etc., for the
hazardous locations were defined. However it was not until 1935 that Groups were introduced into the
NEC. (Note: Divisions were introduced into the NEC in 1947.) The four gas Groups, A, B, C, and D,
complemented the design of electrical equipment used in hazardous (classified) locations and were
defined based on the level of hazard associated with explosion pressures of specific atmospheres and the
likelihood that the effects of that explosion could be transmitted outside the enclosure. Group A was
defined as atmospheres containing acetylene. Group B was defined as atmospheres containing hydrogen
or gas or vapors of equivalent hazard. Group C was defined as atmospheres containing ethyl ether vapor;
and Group D was defined as atmospheres containing gasoline, petroleum, naphtha, alcohols, acetone,
lacquers solvent vapors, and natural gas.
Despite the fact that the introduction of these Groups was done without standardized testing and without
the advantage of todays technological advances or equipment, these definitions have changed little since
that time. The first major testing, in fact, was only conducted in the late 1950s, when engineers at
Underwriters Laboratories developed a test apparatus that provided a means to determine how various
materials behaved with respect to explosion pressures and transmission, when the specific combustible
material was ignited in the test vessel. This apparatus, called the Westerberg Explosion Test Vessel,
provided standardized documentation of a factor called the Maximum Experimental Safe Gap (MESG) and
permitted other materials to be classified by test into one of the four gas groups. The results of these
tests are contained in Underwriter Laboratories (UL) Bulletin Nos. 58 and 58A (reissued in July, 1993, as
UL Technical Report No. 58). In 1971, the International Electrotechnical Commission (IEC) published IEC
79-1A defining a different type of apparatus for obtaining MESG results. While the two MESG test
apparatus are physically different in both size and shape, the results are statistically comparative, although
in some cases differences have been observed. A sample of values is shown in the following table:
Material
Westerberg apparatus
MESG in mm
IEC apparatus
MESG in mm
Propane
0.92
0.94
Ethylene
0.69
0.65
Butadiene
0.79
0.79
Diethyl ether
0.30( 0.60)
0.87
Hydrogen
0.08 ( 0.23)
0.29
ANSI/ISA12.01.011999
26
Additional testing on the Westerberg Apparatus has demonstrated that this theory was true, and the MESG value for
diethyl ether more than doubled. Further, Westerberg apparatus testing has also shown that the hydrogen MESG value
is 0.23 mm.
Papers have been written to attempt to explain the reasons for these differences in the test data. One, by
H. Phillips, entitled Differences Between Determinations of Maximum Experimental Safe Gaps in Europe
and U.S.A., appeared in a 1981 edition of the Journal of Hazardous Materials and cited a condition of
spontaneous combustion in one portion of the Westerberg Apparatus, which was reflected in materials,
like diethyl ether, having low ignition temperatures.
While acetylene remains segregated in Group A because of the high explosion pressure, which results
from its very fast flame speed, newer test methodologies have defined other types of protection methods
that now consider acetylene and hydrogen to be of equivalent hazard. One such method examines the
MINIMUM IGNITION CURRENT required to ignite a specific combustible material. This testing produced more
variability when the results of specific combustible materials were compared. However, it was found that
the minimum ignition currents of one test could be favorably compared with those of other tests if a ratio
value based on methane was applied. This testing has resulted in the generation of MIC Ratio data.
Other testing has been performed when it was incorrectly assumed that factors called minimum ignition
energy (MIE) and autoignition temperature (AIT) were related and could be used to place materials into
Groups. The fact that these were independent factors resulted in deletion of AITS as a basis for Group
determination in the 1971 NEC.
MIEs have been found to exhibit theoretical results, which do not translate into practical designs that can
be applied to actual electrical devices with their associated energy levels.
Since the primary concern is to have electrical devices that can safely operate when used in locations
classified by Class, Group, and Division, the delineations for the gas groups have been defined on the
basis of MESG and MIC RATIO.
Further details may be found in NFPA 497.
4.2.2
Division 2 concept
The concept of Division 2, a location in which flammable material will be present only occasionally, was
initiated in North America. It was recognized that if the probability of the presence of flammable material is
low, the protective measures necessary to prevent an explosion can be less restrictive (and normally also
much less expensive) than those required in Division 1 locations. In Division 1 locations the probability
that the flammable material is present is much higher than in Division 2 locations because in the former,
the flammable atmosphere is present frequently during normal operations. Although many international
corporations, particularly oil and chemical companies, used the North American nomenclature and
practice, it was not until the 1960s that Division 2 began to be accepted outside North America. At the
present time the concept of Division 2 area classification is recognized universally. The relaxation of
protective measures in Division 2 has not yet reached the same level of acceptance, however. In Japan,
for example, the less onerous levels of protection permitted in Division 2 by the National Electrical Code
and the Canadian Electrical Code are not yet recognized.
4.2.3
Zone concept
In the 1960s Europe made its own contribution to the practice of area classification by introducing the
concept of Zone 0. The intent of defining Zone 0 was to define those locations in which the flammable
material is present such a high percentage of the time that extraordinary measures should be taken to
protect against ignition by electrical apparatus. The objective of defining Zone 0 and Zone 1 was to allow
a less restrictive practice in the remainder of locations formerly classified within Division 1. IEC has
recognized three levels of probability that a flammable concentration is present. In IEC terminology, these
27
ANSI/ISA12.01.011999
three levels are Zones 0, 1, and 2. North American Division 1 includes both Zone 0 and Zone 1, and North
American Division 2 is basically equivalent to Zone 2. Though the definitions of zones are similar in almost
all standards, the application of the words to specific industrial situations is different.
4.2.4
Temperature classification
Prior to 1971 the autogenous ignition (or autoignition) temperature, AIT, was a criterion for group
classification. Inclusion of the AIT as one of the classification criteria caused problems for those trying to
classify new materials that had not been tested, because other flammability and combustion parameters of
flammable gases and vapors are not correlated to AIT. For example, the AIT of diethyl ether is 160C
(320F). Hydrogen has an AIT of approximately 520 C (968 F). Methane has an AIT of approximately
630 C (1166 F). Yet hydrogen is much more easily ignited by an arc than diethyl ether. Methane is much
less easily ignited. Hydrogen requires very close-fitting flanges to prevent transmission of an explosion,
but the flanges for an enclosure to protect against transmission of an explosion in diethyl ether may be
much more widely separated, i.e., the MESG of diethyl ether is several times that of hydrogen.
When the 1971 National Electrical Code and the Canadian Electrical Code removed AIT as one of the
criteria for material classification, the practice of temperature marking was introduced. Table 1 lists the
temperature codes recognized in the NEC. Enclosures containing heat-producing devices must be
marked by a temperature code or with the maximum surface temperature of the enclosure based on 40C
(104F) ambient. Those that do not have an alphabetical suffix, i.e., T1-T6, are recognized internationally
by the International Electrotechnical Commission (IEC), by CENELEC, and by many national standards
bodies. In the United States and Canada, equipment of the nonheat-producing type (such as junction
boxes, conduit, and fittings) and equipment of the heat-producing type (such as industrial process
transmitters and transducers) having a maximum temperature not more than 100 C (212 F) need not be
marked. The temperature classification marking also applies to surfaces other than those of the
enclosures in the case of intrinsically safe and nonincendive equipment.
ANSI/ISA12.01.011999
28
Table 1 Temperature identification numbers
Maximum Surface Temperature
4.2.5
Degrees C
Degrees F
Identification Number
450
842
T1
300
572
T2
280
536
T2A
260
500
T2B
230
446
T2C
215
419
T2D
200
392
T3
180
356
T3A
165
329
T3B
160
320
T3C
135
275
T4
120
248
T4A
100
212
T5
85
185
T6
Grouping of materials
4.2.5.1 A hazard grouping of materials is always relative to a stated property, i.e., to a particular ignition
mechanism or a means of hazard reduction. Materials that are very much alike relative to ignition by
electrical arcs or materials that have similar MESG may behave quite differently with respect to ignition by
a hot surface.
4.2.5.2 Table 2 compares several countries/organizations designations of gas groups. At the present
time most national standards use the IEC group designations, where II indicates an above-ground facility
and I indicates a hazard due to methane in the below-ground works of a mine. The comparisons of
Table 2 are approximate. For example, North American Group C is approximately the same list of
materials as IEC Group IIB. Grouping is an arbitrary designation of dividing lines in a continuous series of
values of a particular parameter.
29
ANSI/ISA12.01.011999
Table 2 Comparison of classification of flammable

vapors and gases (approx.).
IEC
(60079-12)
UK
(BS4683)*
UK
(BS229:
1957)*
Germany
(VDE0171) *
USA National
Electrical
Code
Group
Typical gases
and vapors
IIA
IIA
II
Ethane, propane, butane,

pentane, hexane, methane,
heptane, octane, nonane,
decane, acetic acid, acetone,
methanol, toluene, ethyl acetate
IIB
IIB
III
IIC
IIC
IV
3a
3n
Ethylene, coke oven gas,

dimethyl ether, diethylene,
ethylene oxide
Hydrogen
Carbon disulphide
3b
3c
Class I
Acetylene
Ethyl nitrate
* Prior to CENELEC
Protection techniques for electrical apparatus in hazardous (classified)

locations
The most basic protection technique is to avoid placing electrical equipment in a hazardous (classified)
location. Facility planning should take this factor into account, leaving only those situations where there is
no alternative.
Three basic methods of protection are:
a) explosion confinement;
b) isolation of the ignition source; and
c) energy release limitation.
Within each basic method, one (or more) specific technique necessitates specialized design in order to
minimize the potential risk of operating electrical apparatus in hazardous (classified) locations.
5.1
5.1.1
Explosion confinement and flame quenching

Explosionproof (similar to the international term flameproof)
Explosionproof, applicable to Class I areas only, is a specific protection technique in which the ignition
source, fuel, and oxygen may coexist and ignition may occur. However, any ignition that does occur is
confined within an enclosure strong enough to withstand any explosion pressure associated with the gas
groups for which it is designated. Also, all joints have close enough values and tolerances so that flame,
sparks, or escaping hot gases are cooled sufficiently to prevent the external atmosphere from being
ignited. Additionally, all external surfaces must be kept below the autoignition temperature for the specific
ANSI/ISA12.01.011999
30
gases or vapors involved. The explosionproof technique is gas-group dependent i.e., an enclosure
designed and tested for Class I Group C would not be suitable for use in a Group B atmosphere.
5.1.2
Powder filling
Powder filling is a technique whereby the electrical components are immersed in a powder to a depth
sufficient to ensure that any arcing below the powder cannot ignite the flammable atmosphere surrounding
the apparatus.
The concept was developed in France and generally referred to sand, quartz, or solid glass particles used
as filling materials. At the present time, however, only quartz is permitted. Refer to ISA S12.25.01 (IEC
60079-5 Mod).
5.2
Isolation from flammable atmospheres
Isolation of the ignition source from the flammable atmosphere may be accomplished by several
techniques. Some of the most common techniques include pressurization, purging, continuous dilution,
and inerting.
5.2.1
Pressurization
Pressurization reduces the concentration of any flammable gas or vapor initially present to an acceptably
safe level and isolates electrical components from the external atmosphere by maintaining a pressure
within the equipment enclosure higher than that of the external atmosphere. Thus, the external
atmosphere is prevented from entering the enclosure. Unlike explosionproofing, the purging technique is
not gas-group dependent with the following exceptions:
a) For Type Y, a nonincendive component and nonincendive circuits must be gas-group related.
b) For Type X, door interlock and purge fail power cutoff must be rated for the location.
In the case of enclosures in which flammable materials are intentionally introduced within the enclosure
(such as with gas analyzers), a different technique, commonly referred to as continuous dilution, is
required. Refer to NFPA 496, although this standard does not use the term CONTINUOUS DILUTION. Also
refer to 5.2.2.
5.2.1.1 In North America the pressurization technique is used for reducing the classification within the
enclosure to a lower level, such as from Division 1 to Division 2 or nonhazardous (unclassified) or from
Division 2 to nonhazardous (unclassified). The European and North American requirements agree in
principle, but the bases for the respective requirements are equipment construction criteria. The end result
is essentially the same. Reference IEC 60079-2 and 60079-13.
A discussion of three different sets of requirements dependent upon the area classification and the nature
of the enclosed apparatus follows.
United States and Canada
Type X Pressurization. In the United States and Canada, Type X pressurization is a method of reducing
the classification within an enclosure from Division 1 to nonhazardous (unclassified). Type X purging
requires that the enclosure pressure be monitored and that the electrical power be mechanically
disconnected upon loss of positive pressure.
Type Y Pressurization. In the United States and Canada, Type Y pressurization is a method of reducing
the classification within an enclosure from Division 1 to Division 2. Devices that employ Type Y
31
ANSI/ISA12.01.011999
pressurization must be suitable for use in Division 2 locations without pressurization. A visual or audible
warning is required for loss of positive pressure.
Type Z Pressurization. In the United States and Canada, Type Z pressurization is a method of reducing
the classification within an enclosure from Division 2 to nonhazardous (unclassified). A visual or audible
warning is required for loss of positive pressure.
International
Types X, Y, and Z pressurization are not currently recognized outside the United States and Canada,
although the concept of Type X, Y, and Z is proposed in the 1997 draft revisions to IEC 60079-2. The IEC
currently uses the designation first case for Type X and Type Y pressurization and second case for
Type Z pressurization. International requirements for visual and/or audible alarms for loss of enclosure
pressure, when the pressurization technique is used, vary from country to country. Loss of pressure may
also require power disconnection.
5.2.1.2
Pressurization for Class II
Pressurization for Class II is the technique of supplying an enclosure with clean air or an inert gas, with or
without continuous flow, at sufficient pressure to prevent the entrance of combustible dusts.
5.2.2
Continuous dilution
Continuous dilution is a derivation of the purging technique and is intended for electrical equipment
enclosures in which a flammable material is deliberately introduced. Such equipment may include gas
analyzers, chromatographs, and similar instruments. The principle involved is to introduce sufficient flow
of protective gas to dilute any flammable gas present during normal operating conditions or failure
conditions to a level well below the lower explosive limit (normally, 25 percent of LFL/LEL). An example of
a failure condition would be a broken tube transporting flammable gas. As with purging, there are three
types of protection, depending upon the conditions of release within the enclosure. The safeguards
include (1) monitoring the presence of the protective gas, (2) removing electrical power, and (3) alarming
depending on the conditions of internal release and the nature of the enclosed electrical components.
Safeguards depend upon whether or not the electrical parts are normally a source of ignition or meet the
requirements for operation in a Division 2 hazardous (classified) location. A continuous dilution system
may also be used as a purging or pressurization system to prevent any external flammable gas or vapor or
combustible dusts from entering the enclosure.
5.2.3
Oil Immersion
While oil immersion is not a common protection technique for instruments, it is an acceptable isolation
method. The most common application is for electrical equipment such as switches, relays, and
transformers. All electrical parts are submersed in either nonflammable or low-flammability oil, which
prevents the external atmosphere from contacting the electrical components. The oil often serves also as
a coolant. Refer to ISA S12.26.01 (IEC 60079-6 Mod).
5.2.4
Sealing (sealed device)
Sealing is a technique primarily applicable to Division 2 classified areas. The basic principle provides for
the isolation of electrical components within an enclosure by sealing the enclosure well enough to prevent
the casual entrance of any external flammable atmosphere. Sealing may be accomplished by several
means, from simple gasketing to a glass-to-metal hermetic seal. Reference ISA-S12.12, IEC 60079-15,
and CEC 22.2, No. 213, for further information.
ANSI/ISA12.01.011999
32
A hermetic seal is considered effective enough to be insensitive to gas group, but a gasketed enclosure is
sensitive to particular gases/vapors (based on their diffusion constants and on the effectiveness of the
gasket seal). For example, hydrogen, with its small molecular structure, will diffuse much more easily than
the heavier hydrocarbons.
The sealing technique has been applied in Europe to a variety of process control equipment. In North
America, hermetically sealed components such as relays, push button contacts, and limit, level, and
pressure switches are commonly used.
The following are two levels of protection provided by sealing: (1) the enclosure is sealed, and (2)
application is restricted to areas that become hazardous only upon equipment or process failure (Division
2).
5.2.5
Encapsulation
Potting or casting are both isolating techniques in which the electrical parts are encapsulated in a solidified
electrically insulating material, preventing the flammable atmosphere from contacting the electrical
components. Most encapsulation has been for the purpose of isolating hot components from the
atmosphere in order to obtain a lower temperature rating or to permit reduced creepage distances
because the spacings are shielded from conductive contamination. Reference ISA-S12.23.01 (IEC 6007918 Mod).
5.2.6
Inert gas filling
Inert gas filling is a technique of filling the interior of an enclosure with an inert gas. It typically is used in
conjunction with sealed or pressurized enclosures. Refer to 5.2.4.
5.3
5.3.1
Energy release limitation

Intrinsic safety
The application of intrinsic safety is limited to equipment and circuits in which the available energy required
for operation is inherently low. Intrinsic safety involves the limitation of the available energy in a circuit to a
level at which any spark or thermal effect is incapable of causing ignition of a flammable atmosphere under
test conditions that include the application of circuit and component faults. As a result, the technique is
widely used in the instrument industry, e.g., 4 to 20 mA signal circuits; temperature, flow, pressure, and
level measurement instruments; portable battery-operated instruments (radios, combustible gas
detectors). Certain fault conditions need to be considered in the design and evaluation. For installation
information, refer to ISA-RP12.6 and NEC Article 504.
5.3.2 Nonincendive equipment (internationally referred to as energy limited apparatus and
circuits)
The nonincendive approach is similar to the intrinsic safety approach in basic principle but differs greatly in
detail. There are two major differences. First, nonincendive circuits are evaluated under normal conditions
only (i.e., no fault conditions need to be considered). Equipment meeting the nonincendive criteria is
suitable for use only in Division 2 areas in which the atmosphere is normally nonflammable and requires a
breakdown in the process or the process equipment to make it flammable.
Second, relative to the components used, few detailed requirements must be met other than those
applicable to nonhazardous (unclassified) location use as related to personnel shock and fire hazard. A
typical analysis involves itemizing all parts that could potentially interrupt a circuit such as switches, relays,
connectors, and potentiometers. These components are then analyzed or tested to see if they can ignite
the specified flammable atmosphere.
33
5.4
5.4.1
ANSI/ISA12.01.011999
Other methods of protection

Restricted breathing
Restricted breathing is a technique developed by the Swiss. It can be considered to be a modified form of
sealing. In the Swiss utilization of the technique, fairly large enclosures of relays and other ignitioncapable apparatus are gasketed so they are tightly sealed. The protection principle employed is that the
enclosure is sufficiently tight to make it highly unlikely that a flammable cloud of gas would surround the
enclosure for the length of time necessary for enough flammable material to enter the enclosure that a
flammable concentration would exist in the enclosure. This technique is applicable only to Zone 2
locations. Refer to IEC 60079-15 and ISA S12.12.01.
5.4.2
Increased safety
Increased safety is a technique developed in Germany. It has been used for equipment such as terminals,
motors, and lighting fixtures. The motors are specially designed to remain below the autoignition
temperature, even under certain locked rotor conditions, and have special connection facilities designed to
prevent loosening even under severe vibration. Refer to IEC 60079-7 and ISA S12.16.01.
5.4.3
Dust-ignitionproof
Dust-ignitionproof enclosures are essentially sealed enclosures that prevent the entrance of dusts.
Additionally, the outer enclosure temperature must be maintained below specific limits. For additional
information, refer to UL 1203.
5.5
Summary of Types of Protection
Table 3 provides a summary of various Types of Protection and locations in which they are permissible.
ANSI/ISA12.01.011999
34
Table 3 Summary of Types of Protection

(flammable gases or vapors-in-air mixtures)
Designation
Technique
Zone *
Flameproof enclosure
Increased safety
ia
Intrinsic safety
ib
Intrinsic safety
[ia]
Intrinsically safe associated apparatus
Non-hazardous
[ib]
Intrinsically safe associated apparatus
Non-hazardous
Encapsulation
nA
Non-sparking equipment
nC
Sparking equipment in which the contacts are

suitably protected other than by restricted breathing
enclosure.
nR
Restricted breathing enclosure
Oil immersion
Purged and pressurized
1 or 2
Powder-filled
* Does not address use where a combination of techniques is used.
For protection techniques (Types of Protection) applicable to Classes I, II, and III; Division 1 and 2, refer to
Article 500-4(a) of the NEC.
5.5.1 A special protection category, Type s, is a technique other than those that have been
standardized. When an area is classified Zone 0, it is common in some countries to provide two or more
protection techniques, such as pressurizing a flameproof enclosure. Ex s has also been applied for Zone
1, where, for example, a transmitting device partly satisfies the increased safety requirements and also
partly satisfies the intrinsic safety requirements. The combination results in a device that is safe for use in
a hazardous (classified) location but does not satisfy a specific set of requirements for a single protection
technique.
5.5.2 The intrinsic safety column indicates that there are two sets of requirements ia and ib; ia is
intended for Zone 0 applications while ib is for Zone 1 applications. The difference in requirements is that
ia considers two simultaneous faults while ib considers only one. The approach of the United States and
Canada (in the Division system) uses the two-fault criteria for all intrinsic safety applications since a
Division 1 area classification includes both the Zone 0 and Zone 1, and equipment must be rated to the
most stringent (Zone 0) requirements.
35
ANSI/ISA12.01.011999
Wiring methods
For the installation of electrical apparatus, three basic installation systems are allowed:
a) Conduit systems (Reference Figures 11, 13, and 15 and Tables 4a and 4b)
b) Cable systems with indirect entry (Reference Figures 5, 6, 12, 14, and 15 and Tables 4a and 4b)
c) Cable systems with direct entry (Reference Figure 7, 8, 9, 12, 14 and 15 and Tables 4a and 4b)
NOTE INTRINSICALLY SAFE ELECTRICAL APPARATUS and NONINCENDIVE FIELD WIRING can be installed with less restrictive wiring
methods. See NEC Section 504-20 or 501-4(b) Exception, respectively.
In the United States, NEC Article 501-4 allows only 1) a conduit system, 2) mineral-insulated (Type MI)
cables, or 3) in industrial establishments with restricted public access where the conditions of maintenance
and supervision ensure that only qualified persons will service the installation, Type MC cable, listed for
use in Class I, Division 1 locations, with a gas/vaportight continuous corrugated aluminum sheath, an
overall jacket of suitable polymeric material, separate grounding conductors in accordance with Section
250 and provided with termination fittings listed for the application.
NEC Article 501-4(b) allows for the use of certain other types of cables in Division 2 areas.
The European harmonized standards, EN 50014 through EN 50039 permit apparatus to be designed that
can be installed using one or more of the three installation approaches. The installation requirements,
however, are different from country to country.
NOTE All figures referred to in this section are shown below.
Figure 1 Vertical conduit seal
ANSI/ISA12.01.011999
36
Figure 2 Conduit drain seal
Figure 3 Cable seal
37
Figure 4 Conduit drain seal
Figure 5 Cable system (indirect entry)
ANSI/ISA12.01.011999
ANSI/ISA12.01.011999
38
Figure 6 Cable gland (indirect entry)
Figure 7 Cable system (direct entry)
39
Figure 8 Cable gland (direct entry)
Figure 9 Conduit system (direct entry)
ANSI/ISA12.01.011999
ANSI/ISA12.01.011999
6.1
6.1.1
40
Conduit system
General
With conduit systems in Class I, Division 1, locations in the United States, the electrical wiring is installed
inside closed threaded metal pipes (rigid steel or intermediate metal conduit) approved for the purpose.
The pipes, in turn, are screwed into entrances in the enclosures, which contain electrical equipment. The
entire conduit system, including all fittings, is required to be explosionproof and frequently requires an
explosionproof seal between the connected enclosure and the pipe. In Class I, Division 2, locations, the
conduit system need be explosionproof only between any explosionproof enclosure and the required
sealing fittings.
In Class I, Division l, locations in Canada, one difference is that threaded intermediate metal conduit is not
acceptable.
In this section all references to seal and sealing refer to an approved conduit or cable seal that is filled with
suitable compound, is designed to contain an explosion in the enclosure to which it is attached, and is
approved for use in Class I locations [Figures 1, 2, 3, and 4] (see Article 501 of the NEC).
6.2
Cable systems
In the United States, in Class I, Division 1, locations, the NEC will allow 1) mineral-insulated Type MI cable,
2) Type MC or Type ITC cable listed for use in Class I, Division 1, locations, with a gas/vaportight
continuous corrugated aluminum sheath, an overall jacket of suitable polymeric material, separate
grounding conductor in accordance with Section 250, and provided with termination fittings listed for the
application (Figure 3), and 3) cables used in intrinsically safe systems as permitted by Article 504 of the
NEC. For Class I, Division 2 locations, certain cable constructions are allowed. Refer to Table 4a.
Internationally, openly installed cable systems are common, using heavy-duty sheathed cables (i.e., with
an outer sheath of rubber, plastic, or metal). Armored or braided cable is often required in Zone 1 or in
areas where damage might occur to unprotected cable. The metal braid or armor is covered by an outer
sheath of rubber, plastic, or other synthetics, and the braid or armor is grounded.
Different technologies have been developed in various countries regarding the entry of cables into
explosionproof (flameproof) enclosures. In the course of harmonizing the standards, all these entry
possibilities were included in the CENELEC standards.
6.2.1 Indirect Entry - In Germany, and in many other countries influenced by German technology, only
indirect entry (via a terminal chamber that provided increased safety protection) and factory potted and
installed flameproof cable entries were allowed.
Cables enter the terminal chambers via cable glands and connect to increased safety terminals (Figures 5
& 6). Then the single conductors enter into the flameproof chamber via post-type bushings or conductor
bushings. The installer needs only to open the terminal chamber of increased safety for connection, not
the flameproof chamber. Flameproof cable glands are not required.
6.2.2 Direct Entry - Cables enter the flameproof chamber directly. For cable entry, suitable flameproof
cable glands must be used. (Figures 7 & 8)
6.3
Conduit and cable seals
Seals are installed in conduit and cable systems (except for Type MI cable systems with approved
explosionproof terminations) to
41
ANSI/ISA12.01.011999
a) confine an explosion occurring in an enclosure or a conduit system to only that enclosure or that
portion of the conduit system;
b) minimize the passage of gases, vapors, or liquids and prevent the passage of flames through the
conduit or cable system from a classified to an unclassified area, or from one enclosure to another;
c) prevent pressure piling the buildup of pressure inside conduit systems (ahead of an explosions
flame front) caused by precompression as the explosion travels through the system. Exploding
precompressed gases may reach pressures that would exceed the design pressure of the enclosures.
6.3.1
6.3.1.1
Seal requirements
Enclosure entries
In Division 1 and Division 2 locations, a seal must be installed in every conduit or cable system (reference
NEC Article 501-5 for requirements) that enters an enclosure containing arcing, sparking or high
temperature apparatus in which the enclosure is required to be explosionproof.
Multiconductor cables should be sealed in an approved fitting only after removing the jacket and any other
coverings so the sealing compound will surround each individual insulated conductor and the outer jacket
of the cable. The multiconductor cable may be treated as a single conductor if the cable end is sealed by
an approved means within the enclosure.
The conduit system between an enclosure and the required seal must be explosionproof, even in Division
2 locations, since the conduit system must be able to withstand the same internal explosion as the
enclosure to which it is attached. In Division 1 and Division 2 locations, approved explosionproof unions,
couplings, elbows, reducers, and conduit bodies similar to L, T, or Cross types are the only fittings
allowed between the sealing fitting and the enclosure. The conduit body cannot be larger than the trade
size of its associated conduit.
In addition to the above, in Division 1 areas only, explosionproof seals must be installed in each two-inch or
larger conduit run entering an enclosure that contains splices, taps, or terminals. All seals must be
installed within 18 inches (457 mm) from the enclosures to which they are attached.
6.3.1.2
Process Instruments
Seals and drains shall be installed in each conduit or cable connection to devices installed on process
lines that contain flammable fluids and depend upon a single compression seal, diaphragm, or tube (such
as a Bourdon tube) as a barrier between the process fluid and the conduit or cable. This is to prevent
flammable process fluids from entering conduit or cable systems and being transmitted to unclassified
areas or to electrical arcing or high temperature devices in other portions of the system if the process seal
fails. The additional seal and the interconnecting enclosure or conduit or cable system shall meet the
temperature and pressure conditions to which they will be subjected upon failure of the compression seal.
Ordinary conduit or cable seals typically may not meet this criterion due to their leakage rate. Typical
examples of such devices are solenoid valves and pressure, temperature, and flow switches or
transmitters. This requirement applies even in unclassified areas. Draining provisions must be such that
process-line leaks past the process seal will be obvious.
6.3.1.3
Classified area boundaries
Wherever a conduit run passes from a Division 1 to a Division 2 area, from a Division 2 to an unclassified
area, or any other combination thereof, a seal must be placed in the conduit run at the boundary, on either
side. The conduit system must not contain any union, coupling, box, or other fitting between the sealing
fitting and the point at which the conduit leaves the Division 1 or Division 2 area. An exception to the
ANSI/ISA12.01.011999
42
above is that an unbroken rigid metal conduit that passes completely through a Division 1 or a Division 2
area is not required to be sealed if the termination points of the unbroken conduit are in unclassified
locations and the conduit has no fitting less than 12 inches (305 mm) beyond each boundary.
If drain seals are used at an area classification boundary, care must be exercised in the placement of such
seals to ensure that gases or vapor cannot be communicated across the boundary through the conduit
system by way of the seals drain passage. Reference Figure 10.
Cables with an impervious continuous sheath do not have to follow the same sealing requirements as
conduit systems when crossing Division 2 unclassified area classification boundaries. Such cables are not
required to be sealed unless the cable is attached to process equipment or devices that may cause a
pressure in excess of 6 inches of water (1.5 kPa) to be exerted at a cable end. In this case, a seal or other
means shall be provided to minimize migration of flammables into an unclassified area or to arcing or high
temperature devices in other portions of the system, in accordance with NEC Article 501. No seal is then
required at the boundary location. Cables with an unbroken, impervious, continuous sheath are permitted
to pass through a Division 2 unclassified area classification boundary without seals.
Figure 10 Placement of drain seals (Reference API RP 14F, Figure 7,

Recommended Practice for Design and Installation of Electrical Systems for Fixed
and Floating Offshore Petroleum Facilities for Unclassified and Class I, Division 1
and Division 2 Locations)
43
6.3.1.4
ANSI/ISA12.01.011999
Installation
In addition to being placed in proper locations, the following practices should be observed when installing
sealing fittings:
a) Sealing fittings must be accessible.
b) Sealing fittings must be mounted only in the positions for which they were designed. Some seals are
designed only to be installed vertically; some can be installed either vertically or horizontally; a third
type can be installed in any position.
c) Pouring hubs must be properly oriented. The hub through which the sealing compound is to be poured
must be installed above the sealing cavity to properly pour the seal.
d) Only a sealing compound and fiber approved for a particular sealing fitting should be used, and the
manufacturers instructions should be followed for the preparation of dams (if applicable) and the
preparation and installation of the sealing compound. Particular attention should be paid to
temperature limitations of the sealing compound during installation.
e) No splices or taps are allowed in sealing fittings. Sealing compounds may not be insulation materials
and may absorb moisture, causing grounding of the circuit conductors.
f)
Sealing fittings with drain provisions should be installed at the low points of a conduit system to allow
drainage of conduit where water or fluids may accumulate in the conduit/system.
g) Factory-sealed devices such as toggle switches, push buttons, lighting panels, and lighting fixtures
eliminate the need for externally sealing those particular devices.
6.4
Comparison of the installation systems
ANSI/ISA12.01.011999
44
Figure 11 depicts a typical international Group II, Zone 1 conduit system installation.
Figure 11 Typical international Group II, Zone 1 conduit system installation
45
ANSI/ISA12.01.011999
Figure 12 depicts a typical international Group II, Zone 1 cable system for a similar installation.
Figure 12 Typical international Group II, Zone 1 cable system installation
ANSI/ISA12.01.011999
46
Figure 13 depicts a typical United States and Canadian Class I, Division 1 conduit system installation.
Figure 13 Typical United States and Canadian Class I, Division 1 conduit system
installation (Reference API RP 14F, Figure 1, Recommended Practice for Design
and Installation of Electrical Systems for Fixed and Floating Offshore Petroleum
Facilities for Unclassified and Class I, Division 1 and Division 2 Locations)
47
ANSI/ISA12.01.011999
Figure 14 depicts a typical United States and Canadian Class I, Division 1 cable system installation.
Figure 14 Typical United States and Canadian Class I, Division 1 cable system
installation (Reference API RP 14F, Figure 2, Recommended Practice for Design
and Installation of Electrical Systems for Fixed and Floating Offshore Petroleum
Facilities for Unclassified and Class I,
Division 1 and Division 2 Locations)
ANSI/ISA12.01.011999
48
Figure 15 depicts a typical United States and Canadian Class I, Division 2 conduit/cable system
installation.
Figure 15 Typical United States and Canadian Class I, Division 2 conduit/cable

system (Reference API RP 14F, Figure 3, Recommended Practice for Design and
Facilities for Unclassified and Class I,
Division 1 and Division 2 Locations)
49
6.5
ANSI/ISA12.01.011999
Comparisons of wiring methods [see Tables 4a and 4b]
6.5.1
Comparison of cable and conduit systems
Metallic conduit systems have been widely used in the United States and Canada to provide physical and
environmental protection to conductors for both hazardous and nonhazardous locations. Conduit systems
also prevent the transmission of an internally generated cable or conductor insulation fire within one
conduit from spreading to an adjacent conduit, thus offering superior fire resistance. Ferrous metallic
conduit can provide substantial magnetic shielding on sensitive circuits. Because conduit systems provide
a closed system for the transmission of gases from one area to another, they must rely on properly located
and properly installed conduit seals to provide explosionproof system integrity. Conduit systems are
subject to internal condensation and resulting corrosion, which, if unchecked, can compromise explosion
protection, especially with regard to offshore or shoreline locations. Also, under certain conditions, conduit
systems can provide a passageway for liquids and gases, possibly transmitting corrosive or toxic
substances to control rooms and electrical equipment buildings. In some countries, conduit systems are
not recognized or accepted.
In many instances, cable systems offer an attractive alternative to conduit systems and are used
worldwide. Cable systems may be less labor intensive during the initial installation and in follow-up
maintenance. Certain types of cable construction and termination methods offer greater corrosion
protection than conduit systems and offer an overall increase in system integrity due to reduced long-term
corrosion effects. Cable systems provide the benefit that they are visible, which allows for ongoing
inspection and simplifies the task of tracing circuits. There are numerous types of cables that are
permitted in hazardous areas.
6.5.2
Comparisons between direct and indirect cable entries
A comparison between cable systems with direct and indirect entry shows some advantages to the indirect
method, the system with terminal chambers that uses the INCREASED SAFETY type of protection. The
installer can connect the indirect-entry type without opening the flameproof equipment chamber. With the
cable system that uses direct entry, the flameproof protection completion can be achieved only during
installation (on site).
Direct entry technology requires that the wiring connections be accomplished in the flameproof chamber.
When using indirect entry, the connection is to terminals made in a separate terminal chamber that may be
type of protection INCREASED SAFETY or FLAMEPROOF.
Grounding and bonding practices
7.1
In the United States and Canada, grounding and bonding practices in hazardous (classified) locations
must follow the same standards as grounding and bonding practices in nonhazardous (unclassified)
locations. In addition, the following special precautions must be followed:
a) Locknut bushings and double-locknut bushings must not be used as the only bonding method but must
be paralleled with bonding jumpers. Reference NEC 501-16(a).
b) Flexible-metal conduit or liquid-tight flexible-metal conduit must not be used as the only grounding path
but must be paralleled with internal or external bonding jumpers. Reference NEC 501-16(b).
c) All conduit must be threaded (NPT standard threads with 3/4 inch taper per foot) and made wrenchtight to prevent sparking when fault current flows through the conduit system. Reference NEC 500-2.
d) When required by the control drawing, intrinsically safe systems must be provided with a dedicated
grounding conductor separate from the power system so that ground currents will not normally flow.
ANSI/ISA12.01.011999
50
The systems must be reliably connected to a ground electrode in accordance with NEC Article 250 or
CEC Part 1, Section 10. (Reference ISA-RP12.6)
7.2
Internationally, the term EARTHED is used instead of GROUNDED, but the same basic practices are
followed.
Table 4a Field wiring in United States Class I locations a,b
Zone 0
Division 1 / Zone 1
Division 2 / Zone 2
Wiring system
IS
NIS
IS
NIS
IS or
Nonincendive
NIS
Threaded rigid metal

conduit
Threaded steel
intermediate metal conduit
Flexible metal
explosionproof fitting
Types MI, MC, & ITC

cable
Adg
Types PLTC, HV, ITC, and

TC cable
Flexible metal conduit
Ac,f
Liquid-tight, flexible metal

conduit
Ac,f
Electrical metallic tubing

(steel)
Flexible cord
Note 1
Ac,e
Note 1 or 2
Any other wiring method

suitable for nonhazardous
locations
a Abbreviations: IS = intrinsically safe; NIS = not intrinsically safe; A = acceptable; X = not acceptable.
b See the NEC for description and use of wiring systems.
c Acceptable only where flexibility is needed.
d Acceptable only with termination fittings approved for Class I, Division 1 locations of the proper groups.
e Extra-hard usage type with a grounding conductor only acceptable.
f Special bonding/grounding methods are required.
g Type MC or Type ITC cable approved for Division 1 permitted in industrial establishments, see NEC 501-4 (a) Exception 2 or 3.
NOTE 1 Acceptable on approved portable equipment where provisions are made for cord replacement, per NEC 501-11.
NOTE 2 Acceptable on process control instruments to facilitate replacements, per NEC 501-3(b) (6).
51
ANSI/ISA12.01.011999
Table 4b Field wiring in United States Class II locations a,b
Division 1
Wiring system
Division 2
IS
NIS
IS or Nonincendive
NIS
Threaded rigid metal conduit
Threaded steel intermediate metal

conduit
Flexible metal explosionproof fitting
Ac
Ac
Type MI cable
Ad
Ae
Type MC cable
Ad
Xi
Type PLTC, ITC, and TC cable
Ad
Af
Flexible metal conduit
Ad
Liquid-tight, flexible metal conduit
Ad
Ac,d,g
Ac,d,g
Flexible cord
Ad
Ac,d,h
Ac,d,h
Dust-tight wireways and raceways
Any other wiring method suitable for

nonhazardous locations
Ad
Electrically metallic tubing
Ad
a Abbreviations: IS = intrinsically safe; NIS = not intrinsically safe; A = acceptable; X = not acceptable.
b See the NEC for description and use of wiring systems.
c Acceptable only where flexibility is needed.
d Acceptable only with dust-tight seals at both ends when electrically conductive dusts will be present.
e Acceptable only with termination fittings approved for Class I, Division 1 locations of the proper groups.
f Acceptable in ventilated channel-type cable trays in a single layer for a space not less than the larger
cable diameter between adjacent cables.
g Special bonding methods are required.
h Only extra-hard usage type with a grounding conductor acceptable.
i Type MC cable approved for Division 1 permitted in industrial establishments, see NEC 501-4 (a) Exception 2.
Maintenance practices
Special attention must be focused on hazardous location equipment maintenance procedures in order to
maintain the integrity of the original installation. The following are pertinent maintenance practices.
8.1
Hazardous location equipment can be repaired only in accordance with the manufacturers
instructions. Some codes of practice require the recording of repairs and the inspection of the completed
repair by a second competent person.
8.2
Maintenance personnel should ensure that all explosionproof enclosures are properly closed and
furnished with the proper number and type of fasteners. Care should be exercised to assure that all machinefinished flanges are protected from damage during maintenance to ensure surface integrity.
8.3
Maintenance personnel should ensure that all grounding conductors are properly terminated.
ANSI/ISA12.01.011999
8.4
52
Any physical abnormalities noted should be corrected or reported to the next level of supervision.
8.5
All threaded connections (including flame paths) should be regularly coated with a lubricant approved
for the purpose.
8.6
Defective circuit protection devices (primarily fuses) must be replaced with functional equivalent
devices (proper amperage, voltage, characteristics, etc.).
8.7
Periodic inspections should be made to ensure that intrinsically safe circuits are isolated from nonintrinsically safe circuits.
8.8
Periodic inspections should be made to ensure that the equipment is suitable for the current area
classification.
8.9
Special care must be taken to ensure that different intrinsically safe circuits do not become shorted
together during calibration and maintenance.
53
ANSI/ISA12.01.011999
Annex A Acronyms
Throughout the text, many acronyms or abbreviations are used. The following list of acronyms provides a
ready reference.
AIT
Autoignition Temperature
ANCE
Asociacin Mexicana Nacional de Normalizacin y Certificacin del Sector Electrico

(Mexico)
ANSI
American National Standards Institute
API
American Petroleum Institute
AS
Australian Standard
ASTM
American Society for Testing and Materials
AWG
American Wire Gauge
BASEEFA
British Approvals Service for Electrical Equipment in Flammable Atmospheres - Part of

EECS (UK)
BS
British Standard
BSI
British Standards Institute
BVFA
Bundesversuchs - und Forschungs - Anstalt (Austria)
BvS
Berggewerkschafitliche Versuchsstrecke [see DMT] (Germany)
CANMET
Canadian Mining and Energy Technology (Canada)
CEC
Canadian Electrical Code
CEN
European Committee for Standardization
CENELEC
European Committee for Electrotechnical Standardization
CEPEL
Centro de Pesquisas de Energia Electrica (Brazil)
CERCHAR
Centre d'Etudes et Recherches des Chourbonnage de France [See INERIS] (France)
CESI
Centro Elettrotecnico Sperimentale Italiano (Italy)
CSA
Canadian Standards Association (Canada)
CSIR
Central Mining Research Institute (India)
DEMKO
Danmarks Elektriske Material Kontrol A/S (Denmark)
DIN
Deutsche Institut fur Normung e.V. (Germany)
ANSI/ISA12.01.011999
54
DIP
Dust-ignitionproof
DNV
Det Norske Veritas (Norway)
DMT
Deutsche MontanTechnologie [See BvS] (Germany)
EECS
Electrical Equipment Certification Service (UK)
EMR
Energy Mines and Resources (Canada)
EN
European Norm (Standard)
EP
Explosionproof
ERA
Electrical Research Association (UK)
FM
Factory Mutual Research Corporation (USA)
GOST
Gossudarstwenny Standard (Russia)
HSE
Health and Safety Executive (UK)
IEC
International Electrotechnical Commission
IECEE
International Electrotechnical Commission Committee on Electrical Equipment
IEEE
Institute of Electrical and Electronics Engineers
IEV
International Electrotechnical Vocabulary (IEC 50)
INIEX
Institut National des Industries Extractives [See ISSeP] (Belgium)
INERIS
Institut National de LEnvironnement Industriel et des Risques (France)
INSEMEX
Institutul National Pentru Securitate Miniera si Protectie Antiexploziva (Romania)
IP
Institute of Petroleum (UK)
IP
Ingress Protection per IEC 529
ISA
Instrument Society of America
ISSeP
Institute Scientific des Service Public [was INIEX] (Belgium)
ISO
International Organization for Standardization
ITS
JIS
Japan Industry Standards (Japan)
KEMA
Keuring van Elektrotechnische Materialen (The Netherlands)
LCIE
Laboratoire Central Des Industries Electriques (France)
55
ANSI/ISA12.01.011999
LEL
Lower Explosive Limit (Lower Flammable Limit)
LFL
Lower Flammable Limit (Lower Explosive Limit)
LOM
Laboratorio Oficial Madariaga (Spain)
LOSC
Londonderry Occupational Safety CentreWork Cover Authority (Australia)
MECS
Mining Equipment Certification ServicePart of EECS (UK)
MESG
Maximum Experimental Safe Gap
MIC
Minimum Igniting Current
MIE
Minimum Ignition Energy
MMS
Minerals Management Service, U.S. Department of the Interior
MSHA
Mine Safety and Health Administration
NAMUR
Normenarbeitsgemeinschaft fur Mess- und Regelungstechnik in der Chemischen

Industrie (German)
NAS
National Academy of Science
NEC
National Electrical Code (ANSI/NFPA 70)
NEMA
National Electrical Manufacturers Association
NEMKO
Norges Elektriske Materiellkontroll (Norway)
NEPSI
National Supervision and Inspection Centre for Explosion Protection and Safety of
Instrumentation (China)
NFPA
National Fire Protection Association
NRC
National Research Council
NRTL
Nationally Recognized Testing Laboratory
NMX
Voluntary Standards (Mexico)
NOM
Norma Official Mexicana (Mexico)
OSHA
Occupational Safety and Health Act (or Administration)
PTB
Physikalisch-Technische Bundesanstalt (Germany)
RIIS
The Research Institute of Industrial Safety of the Ministry of Labour (Japan)
SAA
Standards Association of Australia
SABS
South African Bureau of Standards (South Africa)
ANSI/ISA12.01.011999
56
SCS
Sira Certification Service (UK)
SEV
Schweizerischer Elektrotechnischer Verein (Switzerland)
SIMTARS
Safety in Mines Testing and Research Station (Australia)
SIPAI
Shanghai Institute of Process Automation Instrumentation (China)
SNZ
Standards New Zealand
SMRE
Safety in Mines Research Establishment - Operation Suspended (UK)
SP
Sveriges Provnings och Forskningsinstitut trans: Swedish National Testing and

Research Institute (Sweden)
TIIS
Technical Institute of Industrial Safety (Japan)
TUV-A
Technischer Uberwachungsverein Austria (Austria)
UEL
Upper Explosive Limit (Upper Flammable Limit)
UFL
Upper Flammable Limit (Upper Explosive Limit)
UK
United Kingdom
UL
Underwriters Laboratories Inc. (USA)
ULC
Underwriters Laboratories of Canada
USA
United States of America
USCG
United States Coast Guard
USBM
Former United States Bureau of Mines
VTT
Vaition Tekmillinen Tutkimuslaitos (Finland)
57
ANSI/ISA12.01.011999
Annex B References
AMERICAN GAS ASSOCIATION
AGA XF0277
Classification of Gas Utility Areas
Available from:
AGA
American Gas Association

1515 Wilson Boulevard
Arlington, VA 22209
Tel: 703-841-8564
AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)

C34.1
Voltage Ratings for Electrical Power Systems and Equipment (60 Hz)
Available from:
ANSI

1 West 42nd Street
New York, NY 10036
Tel.: (212) 642-4900

Fax: (212) 302-1286
http://www.ansi.org
AMERICAN PETROLEUM INSTITUTE (API)

RP 14F
Recommended Practice for Design and Installation of Electrical Systems for Fixed and
Floating Offshore Production Facilities for Unclassified and Class I, Division 1 and
Division 2 Locations
RP 14FZ
Recommended Practice for Design and Installation of Electrical Systems for Fixed and
Floating Offshore Production Facilities for Unclassified and Class I, Zone 0, Zone 1, and
Zone 2 Locations
RP 500
Recommended Practice for Classification of Locations for Electrical Installations at

Petroleum Facilities Classified as Class I, Division 1 and Division 2
RP 505
Recommended Practice for Classification of Locations for Electrical Installations at

Petroleum Facilities Classified as Class I, Zone 0, Zone 1, and Zone 2.
Available from:
API
American Petroleum Institute

1220 L Street, NW
Washington, DC 20005-4070
Tel.: (202) 682-8000

Fax: (202) 682-8051
ANSI/ISA12.01.011999
58
AMERICAN SOCIETY OF HEATING, REFRIGERATING AND AIR CONDITIONING ENGINEERS, INC.

(ASHRAE)
ASHRAE Fundamentals Handbook
Available from:
ASHRAE
American Society Of Heating, Refrigerating And Air Conditioning

Engineers
1791 Tullie Circle, N.E.
Atlanta, GA 30329
EUROPEAN COMMITTEE FOR ELECTROTECHNICAL STANDARDISATION (CENELEC)

EN 50 014,
General Requirements
EN 50 015,
Oil Immersion o
EN 50 016,
Pressurized Apparatus p
EN 50 017,
Powder Filling q
EN 50 018,
Flameproof Enclosure d
EN 50 019,
Increased Safety e
EN 50 020,
Intrinsic Safety i
prEN 50 021,
Type of Protection n (Draft)
EN 50 028,
Encapsulation m
EN 50 039,
Intrinsically Safe Electrical Systems i
EN 50 054,
055, 056,
057, and 058;
Instruments for the Detection of Combustible Gases
Available from:
ANSI

11 West 42nd Street
New York, NY 10036
Tel.: (212) 642-4900

Fax: (212) 302-1286
British Standards Institute

389 Chiswick High Road
London, W4 4AL
Tel.: 44-181-996-7000
Fax: 44-181-996-7001
or
BSI
or
59
CENELEC
ANSI/ISA12.01.011999
European Committee for Electrotechnical Standardization

Central Secretariat
rue de Stassart, 35
B-1050 Brussels
Belgium
CANADIAN STANDARDS ASSOCIATION (CSA)

C22.1, Part 1
Canadian Electrical Code
C22.2, No. 25
Enclosures for Class II, Groups E, F, and G Hazardous Locations
C22.2, No. 30
Explosionproof Enclosures for Use in Class I Hazardous Locations
C22.2, No. 145
Motors and Generators for Use in Hazardous Locations
C22.2, No. 152
Combustible Gas Detection Equipment
C22.2, No. 157
Intrinsically Safe and Nonincendive Equipment for Use in Hazardous Locations
C22.2, No. 174
Cables and Cable Glands for Use in Hazardous Locations
C22.2, No. 213
Nonincendive Electrical Equipment for Use in Class I, Division 2 Hazardous

Locations
ISBN 0-921347-39-1
Guide for the Design, Testing, Construction, and Installation of Equipment in

Explosive Atmospheres (2nd Edition), John A. Bossert
Available from:
CSA
Canadian Standards Association

178 Rexdale Boulevard
Etobicoke, Ontario M9W 1R3
Canada
Tel.: (416) 747-4000

Fax: (416) 747-4178
http://www.csa.ca
FACTORY MUTUAL RESEARCH CORPORATION (FM)

Approval Standard
Class No. 3600
Electrical Equipment for Use in Hazardous (Classified) Locations,

Approval Standard
Class No. 3610
Intrinsically Safe Apparatus and Associated Apparatus for Use in

Class I, II, and III, Division 1 Hazardous Locations
Approval Standard
Class No. 3611
Electrical Equipment for Use in Class I, Division 2, Class II, Division

2 and Class III, Divisions 1 and 2 Hazardous Locations
Approval Standard
Class No. 3615
Explosionproof Electrical Equipment
Approval Standard
Class No. 3620
Purged and Pressurized Electrical Equipment for Hazardous

Approval Standard
Combustible Gas Detectors
Class Nos. 6310-6330
ANSI/ISA12.01.011999
60
Available from:
FMRC

1151 Boston-Providence Turnpike
Norwood, MA 02062
Tel.: (781) 762-4300

Fax: (781) 762-9375
http://www.factorymutual.com
INSTITUTE OF ELECTRICAL AND ELECTRONIC ENGINEERS (IEEE)

Std. 45
Recommended Practice for Electrical Installation on Shipboard
Std. 142
Recommended Practice for Grounding of Industrial and Commercial Power

Systems
Available from:
IEEE
Institute of Electrical and Electronic Engineers

445 Hoes Lane
P.O. Box 1331
Piscataway, NJ 08855-1331
Tel: (800) 678-4333

Fax: (732) 562-5445
INSTITUTE OF PETROLEUM (IP)

IP - Part 15
Model Code of Safe Practice in the Petroleum Industry, Part 15: Area
Classification Code for Petroleum Installations
Available from:
IP
Institute of Petroleum
61 New Cavendish Street
London, UK W1M 8AR
ISA
ISA-S5.1
Instrumentation Symbols and Identification
ISA-S7.3
Quality Standard for Instrument Air
ISA-S12.0.01
(IEC 79-0 Mod)
Electrical Apparatus for Use in Class I, Zones 0 and 1, Hazardous

(Classified) Locations: General Requirements
ISA-S12.01.01
Definitions and Information Pertaining to Electrical Apparatus in Hazardous

ISA-dS12.2.01
(IEC 79-11 Mod)
Electrical Apparatus for use in Class I, Zones 0, 1, and 2 Hazardous

(Classified) Locations: Type of Protection Intrinsic Safety i
ISA-RP12.2.02
Recommendations for the Preparation, Content, and Organization of Intrinsic

Safety Control Drawings
ISA-RP12.4
Pressurized Enclosures
ISA-RP12.6
Wiring Practices for Hazardous (Classified) Locations Instrumentation

Part I: Intrinsic Safety
61
ANSI/ISA12.01.011999
ISA-S12.10
Area Classification in Hazardous (Classified) Dust Locations
ISA-S12.11
Electrical Equipment in Hazardous Dust Locations
ISA-S12.12
Electrical Equipment for Use in Class 1, Division 2 Hazardous (Classified)

Locations
ISA-dS12.12.01
(IEC 79-15 Mod)
Electrical Apparatus for Use in Class I, Zone 2 Hazardous (Classified)

Locations: Type of Protection n
ISA-S12.13,
Part I
Performance Requirements, Combustible Gas Detectors
ISA-S12.13,
Part II
Installation, Operation, and Maintenance of Combustible Gas

Detection Instruments
ISA-S12.15, Part I
Performance Requirements for Hydrogen Sulfide Detection Instruments

(10-100 ppm)
ISA-RP12.15, Part II
Installation, Operation, and Maintenance of Hydrogen Sulfide Detection

Instruments
ISA-S12.16.01
(IEC 79-7 Mod)
Electrical Apparatus for Use in Class I, Zones 1 and 2 Hazardous

(Classified) Locations: Type of Protection Increased Safety e
ISA-S12.22.01
(IEC 79-1 Mod)
Electrical Apparatus for Use in Class I, Zone 1 Hazardous

(Classified) Locations: Type of Protection Flameproof d
ISA-S12.23.01
(IEC 79-18 Mod)
Electrical Apparatus for Use in Class I, Zone 1 Hazardous (Classified)

Locations: Type of Protection Encapsulation m
ISA-RP12.24.01
(IEC 79-10 Mod)
Recommended Practice for Classification of Locations for Electrical

Installations Classified as Class I, Zone 0, Zone 1, or Zone 2
ISA-S12.25.01
(IEC 79-5 Mod)

(Classified) Locations: Type of Protection Powder Filling q
ISA-S12.26.01
(IEC 79-6 Mod)

(Classified) Locations: Type of Protection Oil Immersion o
ISA-S51.1
Process Instrumentation Terminology
ISA-S71.01
Environmental Conditions for Process Measurement and Control Systems:

Temperature and Humidity
ISA-S82.01
Safety Standard for Electrical and Electronic Test, Measuring, Controlling, and
Related Equipment General Requirements
ISA-S82.02
Related Equipment Electrical and Electronic Test and Measuring Equipment
ISA-S82.03
Related Equipment Electrical and Electronic Process Measurement and
Control Equipment
ANSI/ISA12.01.011999
62
Calder, W. and Magison, E.C., Electrical Safety in Hazardous Locations, ISA, 1983.
Magison, E.C., Electrical Instruments in Hazardous Locations, ISA, 4th Edition - 1998.
Available from:
ISA
ISA
67 Alexander Drive, P.O. Box 12277
Research Triangle Park, NC 27709
Tel.: (919) 549-8411

Fax: (919) 549-8288
http://www.isa.org
INTERNATIONAL ELECTROTECHNICAL COMMISSION (IEC)

60050
International Electrotechnical Vocabulary (IEV)
60079-0
Electrical Apparatus for Explosive Gas Atmospheres: General Requirements
60079-1
Construction and Verification Test of Flameproof Enclosures of Electrical Apparatus,

Amendment No. 1, Type of Protection d
60079-1A
Construction and Verification Test of Flameproof Enclosures of Electrical Apparatus

First Supplement: Appendix D: Method of Test for Ascertainment of Maximum
Experimental Safe Gap
60079-2
Electrical Apparatus (pressurization), Type of Protection p
60079-3
Spark Test Apparatus for Intrinsically Safe Circuits
60079-4
Method of Test for Ignition Temperature
60079-4A
Method of Test for Ignition Temperature, First Supplement
60079-5
Powder-Filling, Type of Protection q
60079-6
Oil-Immersion, Type of Protection o
60079-7
Increased Safety, Type of Protection e
60079-10
Classification of Hazardous Areas
60079-11
Intrinsic Safety, Type of Protection i
60079-12
Classification of Mixtures of Gases or Vapors with Air According to Their Maximum

Experimental Safe Gaps and Minimum Igniting Currents
60079-13
Construction and Use of Rooms and Buildings Protected by Pressurization
60079-14
Electrical Installation in Explosive Gas Atmospheres (Other than Mines)
60079-15
Electrical Apparatus, Type of Protection n
60079-16
Artificial ventilation for the protection of analyzer houses
63
ANSI/ISA12.01.011999
60079-17
Inspection and maintenance of electrical installations in hazardous areas (other than

mines)
60079-18
Encapsulation, Type of Protection m
60079-19
Repair and overhaul for apparatus used in explosive atmospheres (other than mines or
explosives)
60079-20
Data for flammable gases and vapours relating to the use of electrical apparatus
60529
Degrees of protection provided by enclosures (IP Code)
60654-1
Temperature, Humidity, and Barometric Pressure
61241
Electrical Apparatus for use in the presence of combustible dust
61241-1-1
Part 1: Electrical apparatus protected by enclosures Section 1: Specification for

apparatus
61241-1-2
Part 1: Electrical apparatus protected by enclosures Section 2: Selection, installation,

and maintenance
61241-2-1
Part 2: Test methods Section 1: Methods for determining the minimum ignition
temperatures of dust
61241-2-2
Part 2: Test methods Section 2: Method for determining the electrical resistivity of dust
in layers
61241-2-3
Part 2: Test methods Section 3: Method for determining minimum ignition energy of
dust/air mixtures
61241-3
Part 3: Classification of areas where combustible dusts are or may be present.
61892-7
Mobile and Fixed Offshore Units Electrical Installations

Part 7: Hazardous Areas
Available from:
ANSI

11 West 42nd Street
New York, NY 10036
Tel.: (212) 642-4900

Fax:(212) 302-1286
International Electrotechnical Commission

Bureau Centrale de la Commission
Electrotechnique International
3, rue de Varembe Case
postale 131, 1211
Geneva 20, Switzerland
Tel: 41-22-734-01-50
Tel: 41-22-734-01-50
Fax:41-22-733-38-43
http://www.iec.ch
or
IEC
ANSI/ISA12.01.011999
64
MISCELLANEOUS
Hilado, C.J., "A Method for Estimating Limits of Flammability," Journal Fire Flammability, Vol. 6, pp. 130139 (April 1975).
NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA)
ICS 6
Enclosures for Industrial Controls and Systems
No. 250
Enclosures for Electrical Equipment
Available from:
NEMA
National Electrical Manufacturers Association

1300 North 17th Street
Suite 1847
Rosslyn, VA 22209
Tel.: (703) 841-3200

Fax: (703) 841-3300
http://www.nema.org
NATIONAL FIRE PROTECTION ASSOCIATION (NFPA)

No. 30
Flammable and Combustible Liquids Code
No. 37
Installation and Use of Stationary Combustion Engines and Turbines
No. 45
Fire Protection for Laboratories Using Chemicals
No. 70
National Electrical Code
No. 77
Recommended Practice on Static Electricity
No. 90A
Installation of Air Conditioning and Ventilating Systems
No. 91
Installation of Blower and Exhaust Systems for Dust, Stock, and Vapor Removal or
Conveying
No. 325
Guide to Fire Hazard Properties of Flammable Liquids, Gases, and Volatile Solids
No. 496
Purged and Pressurized Enclosures for Electrical Equipment in Hazardous (Classified)

Locations
No. 497
Recommended Practice on Classification of Flammable Liquids, Gases, or Vapors and of

Hazardous (Classified) Locations for Electrical Installation in Chemical Plants
No. 499
Classification of Combustible Dusts and of Hazardous (Classified) Locations for Electrical

Installations in Chemical Process Areas
Available from:
NFPA
National Fire Protection Association

P.O. Box 9146
Quincy, MA 02269-9959
Tel.: (617) 770-3000

Fax: (617) 770-0700
65
ANSI/ISA12.01.011999
UNDERWRITERS LABORATORIES INC. (UL)

UL Technical An Investigation of Flammable Gases or Vapors with Respect to Explosionproof
Report No. 58 Electrical Equipment
UL 583
Standard for Electric-Battery-Powered Industrial Trucks
UL 674
Standard for Electric Motors and Generators for Use in Hazardous (Classified) Locations,
Class I, Groups C and D, and Class II, Groups E, F, and G
UL 698
Standard for Industrial Control Equipment for Use in Hazardous (Classified) Locations
UL 781
Standard for Portable Electric Lighting Units for Use in Hazardous (Classified) Locations
UL 783
Standard for Electric Flashlights and Lanterns for Use in Hazardous (Classified)
Locations
UL 823
Standard for Electric Heaters for Use in Hazardous (Classified) Locations
UL 844
Standard for Electric Lighting Fixtures for Use in Hazardous (Classified) Locations
UL 877
Standard for Circuit Breakers and Circuit-Breaker Enclosures for Use in Hazardous
(Classified) Locations, Class I, Groups A, B, C, and D, and Class II, Groups E, F, and G
UL 886
Standard for Outlet Boxes and Fittings for Use in Hazardous (Classified) Locations
UL 894
Standard for Switches for Use in Hazardous (Classified) Locations
UL 913
Standard for Intrinsically Safe Apparatus and Associated Apparatus for Use in Class I, II,
and III, Division 1, Hazardous (Classified) Locations
UL 1002
Standard for Electrically Operated Valves for Use in Hazardous (Classified) Locations,
Class I, Groups A, B, C, and D, Class II, Groups E, F, and G
UL 1010
Standard for Receptacle-Plug Combinations for Use in Hazardous (Classified) Locations
UL 1067
Standard for Electrically Conductive Equipment and Materials for Use in Flammable
Anesthetizing Locations
UL 1203
Explosionproof and Dust-Ignitionproof Electrical Equipment for Use in Hazardous

UL 1207
Standard for Sewage Pumps for Use in Hazardous (Classified) Locations
UL 1604
Electrical Equipment for Use in Hazardous (Classified) Locations, Class I and II, Division
2, and Class III, Divisions 1 and 2 Hazardous (Classified) Locations
UL 2225
Standard for Metal-Clad Cables and Cable-Sealing Fittings for Use in Hazardous
ANSI/ISA12.01.011999
66
Available from:
Global Engineering Documents
15 Inverness Way East
Englewood, CO 80112
Tel.: (303) 397-7956

(800) 854-7179
Fax: (303) 397-2740
http://global.ihs.com
To contact UL for other than publications:

333 Pfingston Road
Northbrook, IL 60062-2096
Tel.:(847) 272-8800
Fax: (847) 272-8125
http://www.ul.com
UNITED STATES CODE OF FEDERAL REGULATIONS

Title 30, Parts 1 through 199, Mineral Resources
Title 30, Part 250, Oil and Gas and Sulfur Operations in the Outer Continental Shelf
Title 46, Parts 110 through 113, Shipping Subchapter J, Electrical Engineering, (United States Coast
Guard)
Available from:
Superintendent of Documents
U.S. Government Printing Office
Washington, D.C. 20402
Many of the preceding documents, also available from:
Information Handling Services (IHS)
Englewood, CO 80112
Tel: (800) 525-7052

(303) 790-0600
Fax: (303) 397-2787
http://www.ihsgroup.com
or
Global Engineering Documents
A Division of Information Handling Services
Englewood, CO 80112
Tel: (800) 624-3974

Fax: (303) 397-7935
http://global.ihs.com
67
ANSI/ISA12.01.011999
Annex C Listing of worldwide-codes, guides, and standards

NOTE Annex C is filled as much as possible at the time of publication, but should not be considered
complete. Additions known to the users for consideration for future editions should be directed to:
ISA
67 Alexander Drive
P.O. Box 12277
Attn: Standards Department/SP12
Tel: 919-549-8411
Fax: 919-549-8288
[email protected]
Australia
Austria*
Belgium*
Canada
Standards
SAA
ETVA
ISSeP
CSA
AS 2380.1
AS 2381
AS 3000 Section 9
Oil Immersion/Type o
Pressurization/Type p
AS 2380.4
Powder Filling/Type q
CENELEC
OVE-EX ENx 50 014

OVE-EX 65
NBN C23-001
EN 50 014
CEC 22.1
CSA E79-0
EN 50 014 (1st Ed)

EN 50 014 (2nd Ed)
OVE-EX EN 50 015
NBN C23-104
EN 50 015
CSA E79-6
EN 50 015 (1st Ed)

EN 50 015 (2nd Ed)
OVE-EX EN 50 016
NBN C23-105
EN 50 016
NFPA 496
CSA E79-2
EN 50 016 (1st Ed)

EN 50 016 (2nd Ed)
IEC 60079-5
NBN C23-106
EN 50 017
CSA E79-5
EN 50 017 (1st Ed)

EN 50 017 (2nd Ed)
AS 2380.2
OVE-EX EN 50 018
NBN C23-103
EN 50 018
C22.2 No. 30
CSA E79-1
EN 50 018 (1st Ed)

EN 50 018 (2nd Ed)
Increased Safety/Type e
AS 2380.6
OVE-EX EN 50 019
NBN C23-102
EN 50 019
CSA E79-7
EN 50 019 (1st Ed)

EN 50 019 (2nd Ed)
Intrinsic Safety/Type i
AS 2380.7
OVE-EX EN 50 020
NBN C23-101
EN 50 020
C22.2 No. 157

CSA E79-11
EN 50 020 (1st Ed)

EN 50 020 (2nd Ed)
Type n
AS 2380.9
C22.2 No. 213

CSA E79-15
prEN 50 021
Encapsulation/Type m
AS 2431
CSA E79-18
EN 50 028
Intrinsically Safe Electrical Systems
AS 2380.7
RGPT Article 251 bis

NBN C23-201
EN 50 039
CEC Annex F
EN 50 039
Classification of Hazardous Gas & Vapor Locations
AS 2430 Part 1
NBN C23-001
EN 50 014
CEC Section 18
EN 60 079-10
NBN C23-001
EN 50 014
CEC Annex B
EN 50 014 (1st Ed)

EN 50 014 (2nd Ed)
prEN 60 079-20
IEC 60079-18
OVE-EX65
EX-RL Guidelines No. 11
Classification of Mixtures of Gases & Vapors
Construction of room & bldg. protected by

pressurization
AS 2380.4
IEC E79-13
Area Classification in Hazardous Dust Locations
AS 2430 Part 2
CEC Section 18
prEN 6 1241-3
Electrical Instruments in Hazardous Dust Locations
AS 2236
C22.2 No. 25
prEN 6 1241-1-1
*CENELEC member country
OVE A50
68
Explosionproof/Flameproof/Type d
ANSI/ISA12.01.011999
Country
Country
Denmark*
Standards
DEMKO
Finland*
France*
Germany*
UTE
VDE
Afsnit 7A
Afsnit 50
EN 50 014
SFS 4094
EN 50 014
NF C23-514
NF EN 50 014
Elexv; VDE 0165; EX-RL VDE

0170/0171 Part 1
DIN EN 50 014
Afsnit 50-1
EN 50 015
SFS 4095
EN 50 015
NF C23-515
NF EN 50 015
VDE 0170/0171 Part 2

DIN EN 50 015
Afsnit 50-2
EN 50 016
SFS 4096
EN 50 016
NF C23-516
NF EN 50 016
VDE 0170/0171 Part 3

DIN EN 50 016
Afsnit 50-3
EN 50 017
SFS 4097
EN 50 017
NF C23-517
NF EN 50 017
VDE 0170/0171 Part 4

DIN EN 50 017
Afsnit 50-4
EN 50 018
SFS 4098
EN 50 018
NF C23-518
NF EN 50 018
VDE 0170/0171 Part 5

DIN EN 50 018
Afsnit 50-5
EN 50 019
SFS 4099
EN 50 019
NF C23-519
NF EN 50 019
VDE 0170/0171 Part 6

DIN EN 50 019
Afsnit 50-6
EN 50 020
SFS 4100
EN 50 020
NF C23-520
NF EN 50 020
VDE 0170/0171 Part 7

DIN EN 50 020
Type n
prEN 50 021
NF C23-528
NF EN 50 028
VDE 0170/0171 Part 9

DIN EN 50 028
NF C23-539
NF EN 50 039
VDE 0170/0171 Part 10

DIN EN 50 039
Afsnit 7A
Classification of Mixtures of Gases &

Vapors
Afsnit 7A
Section 41
VDE 0165
DIN EN 60 079-10
VDE 0165
VDE 0171

pressurization
Electrical Instruments in Hazardous Dust

Locations
Afsnit 7A
SFS 2972
NF C20-010
DIN 40050
ANSI/ISA12.01.011999
Classification of Hazardous Gas & Vapor

Locations
Area Classification in Hazardous Dust

Locations
69
Greece*
Hungary
IEC
Irish Republic*
Italy*
Standards
CEI
IEC 60079-0
IEC 60079-0
IEC 60079-0
IS 231
CEI 31-8
CEI 64-2
EN 50 014
IEC 60079-6
IEC 60079-6
IEC 60079-6
IS 232
CEI 31-5
EN 50 015
IEC 60079-2
IEC 60079-2
IEC 60079-2
IS 233
CEI 31-2
EN 50 016
IEC 60079-5
IEC 60079-5
IEC 60079-5
IS 234
CEI 31-6
EN 50 017
IEC 60079-1
MS2 4814
IEC 60079-1
IEC 60079-1
IS 235
CEI 31-1
EN 50 018
IEC 60079-7
IEC 60079-7
IEC 60079-7
IS 236
CEI 31-7
EN 50 019
IEC 60079-11
IEC 60079-11
IEC 60079-11
IS 237
CEI 31-9
EN 50 020
Type n
IEC 60079-15
IEC 60079-15
IEC 60079-15
CEI 31-11
IEC 60079-18
IEC 60079-18
IEC 60079-18
CEI 31-13
EN 50 028

Locations
IEC 60079-10
IEC 60079-10
IEC 60079-10
CEI 64-2

Vapors
IEC 60079-12
IEC 60079-12
IEC 60079-12

pressurization
IEC 60079-13
IEC 60079-13
IEC 60079-13

Locations
Locations
IEC 61241-3
70
ANSI/ISA12.01.011999
Country
Country
Japan
Netherlands*
Norway*
Standards
JIS
NEN
NE
JIS C0903
JIS C0903
JIS C0904
NEN-EN 50 014
NEN-110
NVE Communication 1/77
NEK-EN 50 014
NEN-EN 50 015
NEN-111
NEK-EN 50 015
NEN-EN 50 016
NEN-112
NEK-EN 50 015
NEN-EN 50 017
NEN-113
NEK-EN 50 017
JIS C903
JIS C904
NEN-EN 50 018
NEN-114
NEK-EN 50 018
JIS C903
JIS C904
JIS C905
NEN-EN 50 019
NEN-115
NEK-EN 50 019
JIS C903
JIS C904
NEN-EN 50 020
NEN-116
NEK-EN 50 020
Type n
NEN-3125
NEN-EN 50 028
NEK-EN 50 028
Directorate-General of
Labor Report No. 2E
NEN-1010

Annex II
Portugal*
Decree No. 740/74

Decree No. 36270
PN 721E
71
Poland

BS 5345 Part 1

Vapors
VDE 0171
VDE 0165

pressurization
Locations
Locations
Labour Ordinance
No. 16 RIIS
ANSI/ISA12.01.011999

Locations
Russia
S. Africa
Spain*
Sweden*
Switzerland*
Standards
GOST
SABS
SIEV/SAT
UNE
SEV
SABS 086
SABS 087
SABS 808
SABS IEC 60079-0
SS EN 50 014
SEN 421 0819
Instruccion MI.BT
UNE
20318
SS EN 50 014
SEV 1068
SS EN 50 014
SABS IEC 60079-6
SS EN 50 015
UNE 20326
UNE 21815
SS EN 50 015
SEV 1069
SS EN 50 015
SABS 0119
SABS IEC 60079-2
SS EN 50 016
UNE 20319
UNE 21816
SS EN 50 016
SEV 1070
SS EN 50 016
SABS IEC 60079-5
SS EN 50 017
UNE 20321
UNE 21817
SS EN 50 017
SEV 1071
SS EN 50 017
SABS 314
SABS IEC 60079-1
SS EN 50 018
UNE 20320
UNE 21818
SS EN 50 018
SEV 1072
SS EN 50 018
SABS 1031
SABS IEC 60079-7
SS EN 50 019
UNE 20327
UNE 20328
SS EN 50 019
SEV 1073
SS EN 50 019
SABS 549
SABS IEC 60079-11
SS EN 50 020
SEN 421 0879
UNE 20327
UNE 21820
SS EN 50 020
SEV 1074
SS EN 50 020
Type n
SABS 970
Locations
EN 50 039
SABS 089 Part II
SABS 0108
SAI SIND-FS
SS 421 0820
SS 421 0821

Vapors
SEV 3538
MI.BT 009
MI.BT 026
UNE 20322
SEV 3307-1
UNE 20320

pressurization
SEN 421 0823

Locations
Locations
SABS 969
SEN 2121
SS IEC 529
SEV 1000
72
ANSI/ISA12.01.011999
Country
Country
U.K.*
U.S.A
U.S.A.
U.S.A
U.S.A.
Standards
BS
API
FM
IEEE
ISA
Class No. 3600

(Divisions)
Class No. 3601 (Zones)
ISA-S12.0.01 (Zones)
BS 5501 Part 2
EN 50 015
BS EN 50 015
IEC 60079-6
Class No. 3621
ISA-S12.26.01
BS 5501 Part 3
EN 50 016
BS EN 50 016
IEC 60079-2
Class No. 3620
ISA-RP12.4
BS 5501 Part 4
EN 50 017
BS EN 50 01
IEC 60079-5
Class No. 3622
ISA-S12.25.01
BS 5501 Part 5
EN 50 018
BS EN 50 018
IEC 60079-1
Class No. 3615
ISA-S12.22.01
BS 5501 Part 6
EN 50 019
BS EN 50 019
IEC 60079-7
Class No. 3619
ISA-S12.16.01
BS 5501 Part 7
EN 50 020
BS EN 50 020
IEC 60079-11
Class No. 3610
ISA-RP12.6
Type n
BS 4533
BS 5000
BS 6941
IEC 60079-15
BS/prEN 50 021
Class No. 3611
IEEE Std. 303
ISA-S12.12.01
ANSI/ISA12.01.011999
BS 5501 Part 1
EN 50 014
BS EN 50 014
IEC 60079-0
73
ISA-S12.23.01
ANSI/ISA12.01.011999
ISA-S12.10
74
Country
U.K.*
U.S.A
U.S.A.
U.S.A
U.S.A.
Standards
BS
API
FM
IEEE
ISA
BS 5501 Part 8
EN 50 028
BS EN 50 028
IEC 60079-18
Class No. 3614
BS 5501 Part 9
EN 50 039
BS EN 50 039
Class No. 3610
Classification of Hazardous Gas &

Vapor Locations
BS EN 60 079-10

Vapors
BS 5345 Part 1
BS 5501 Part 1
BS EN 50 014
BS/EN 60079-12
Construction of room & bldg.

protected by pressurization
BS 5345 Part 5
Area Classification in Hazardous

Dust Locations
BS 6467 Part 2
Electrical Instruments in Hazardous

Dust Locations
BS 6467 Part 1
ANSI/API RP 500
ANSI/API RP 505
Class No. 3620
Class No. 3611
ISA-S12.11
Country
U.S.A
U.S.A.
Croatia
Standards
NFPA
UL
DZNM/S-Commission
UL: 508, 698, 1092, 2279 Part 0
UL 2279 Part 2
P.R. of China
HRN N.S8 011

HRN-EN 50 014
GB3836.1
HRN N.S8 501

HRN-EN 50 015
GB3836.6
HRN N.S8 601

HRN N.S8 602
HRN-EN 50 016
GB3836.5
HRN N.S8 701

HRN-EN 50 017
GB3836.7
UL: 674, 698, 781, 783, 823,

844, 877, 886, 894, 1002,
1010,1203,1207,1604,2225,
2279 Part 1
HRN N.S8 101

HRN-EN 50 018
GB3836.2
UL 2279 Part 7
HRN N.S8 201

HRN-EN 50 019
GB3836.3
UL: 913, 2279 Part 11
HRN N.S8 301

HRN-EN 50 020
GB3836.4
Type n
UL: 1604, 2279 Part 15
HRN IEC 60079-15
GB3836.8
UL 2279 Part 18
HRN-EN 50 028
GB3836.9
UL 913
HRN-EN 50 039
NFPA 497

Vapors
NFPA 497

pressurization
NFPA 496
HRN N.S8 610

HRN N.S8 611
HRN IEC 60079-16

Locations
NFPA 499
HRN N.S8 008

HRN IEC 1241-3

Locations
HRN N.S8 007

HRN-EN 60079-10
UL: 58, 58A, 58B
UL: 674, 698, 781, 783, 823,

844, 877, 886, 894, 1002, 1010,
1203, 1604, 2225
HRN N.S8 003

HRN IEC 60079-12
HRN N.S8 850

HRN IEC 1241-1
GB3836.12
GB12476.1
ANSI/ISA12.01.011999

Locations
75
This page intentionally left blank.
77
ANSI/ISA12.01.011999
Annex D Listing of worldwide installation requirements

NOTE Annex D has been filled as much as possible at the time of publication, but should not be
considered complete. Additions known to the users for consideration for future editions should be directed
to:
ISA
67 Alexander Drive
P.O. Box 12277
Attn: Standards Department/SP12
Tel: 919-549-8411
Fax: 919-549-8288
[email protected]
Repair and
Overhaul
Selection of
Instrumentation,
Repair, and
Maintenance for
Dust
Atmospheres
Combustible
Gas Detectors
AS 3000
OVE
EX 65
Belgium
China
NBN C23-201
EN 50 039
RGIE
RGIE Article
251
Electrical
Safety
Regulations
for Explosive
Atmospheres
of Peoples
Republic of
China
Canada
CEC
Denmark
Finland
France
Germany
Greece
Italy
Japan
Heavy
Current
Regulations
Electrical
Safety
Regulations
NF C23539
EN 50 039
EX-RL
Guidelines
No. 11
Elexv ZHI/
227
Elexv ZHI/
200
Elexv ZHI/
309
VDE 0107
VDE 0166
PCC
Regulations
for interior
electrical
installation Chapter X
Presidential decree
DPR 546
Chapter X
CEI 64-2
JISHA Recommended
Practice for
ExplosionProtected
Electrical
Installations in
General
Industries.
JISHA Recommended
Practice for
Electrical
Equipment for
use in Explosive
Dust
Atmospheres in
General
Industries.
78
Inspection &
Maintenance
Austria
ANSI/ISA12.01.011999
Code of
Practice for
selection,
installation and
maintenance
basic
requirements
Australia
Netherlands
Code of Practice
for selection,
installation and
maintenance
basic
requirements
NEN 1010
Norway
NVE
Communications
No. 1/77
Portugal
S. Africa
Decree No.
740/74
Decree No.
517/80
Decree No.
36270
SABS 086
SABS 0119
Spain
Sweden
Instruccion
MI.BT 026
SIEV-FS
Safety
Regulations
SIND-FS
Classification
Regulations
Switzerland
SEV 1000
SEV 3538
U.K.
BS/EN
60079-14
U.S.A.
IEC
NEC/NFPA
70
API RP 14F
API RP 14FZ
(draft)
API RP 540
IEC 60079-14
BS 5345
BS/EN
60079-17
IEC 60079-17
Repair and
Overhaul
BS/EN
60079-19
IEC 60079-19
Selection of
Instrumentation
Repair and
Maintenance for
Dust
Atmospheres
BS 6467
Part 2
BS/EN
61241-1-2
IEC 61241-12
Combustible
Gas Detectors
BS 6959
BS/EN
60079-14
ISA RP 12.13
Part II
API RP 500
API RP 505
IEC 60079-14
79
Inspection &
Maintenance
ANSI/ISA12.01.011999
This page intentionally left blank.
Developing and promulgating technically sound consensus standards, recommended practices, and
technical reports is one of ISAs primary goals. To achieve this goal, the Standards and Practices
Department relies on the technical expertise and efforts of volunteer committee members, chairmen,
and reviewers.
ISA is an American National Standards Institute (ANSI) accredited organization. ISA administers
United States Technical Advisory Groups (USTAGs) and provides secretariat support for
International Electrotechnical Commission (IEC) and International Organization for Standardization
(ISO) committees that develop process measurement and control standards. To obtain additional
information on the Societys standards program, please write:
ISA
Attn: Standards Department
67 Alexander Drive
P.O. Box 12277
ISBN 1-55617-696-1

Isa-12.01.01. Def. Electr. Areas Clasificadas

Uploaded by

Copyright:

Available Formats

Isa-12.01.01. Def. Electr. Areas Clasificadas

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Isa-12.01.01. Def. Electr. Areas Clasificadas

Uploaded by

Copyright:

Available Formats

What is the purpose of this document?

What is the purpose of this document?

What topics does Annex D cover?

What topics does Annex D cover?

AMERICAN NATIONAL STANDARD

Definitions and Information

Approved 21 November 2000

ADDITIONALLY, THE USE OF THIS STANDARD MAY INVOLVE HAZARDOUS MATERIALS,

Waldemar S. Nelson and Company, Inc.

Factory Mutual Research Corp.

The Ohio State University

Figure 1 Vertical conduit seal.......................................................................................................... 35

Figure 10 Placement of drain seals (Reference API RP 14F, Figure 7, Recommended

Table 1 Temperature identification numbers .................................................................................. 28

For hazardous location apparatus, atmospheric conditions are generally considered to be

a) an ambient temperature range of -20 C (-4 F) to 40 C (104 F);

d) a relative humidity of 5 percent to 95 percent.

3.12 Class I location:

3.14 Class I, Division 2 location:

3.23 control drawing:

3.25 dust, combustible:

3.42 explosive atmosphere:

NOTE See also HAZARDOUS (CLASSIFIED) LOCATION.

3.43 fault (as applicable to intrinsically safe systems):

3.46 flammable (explosive) limits:

3.47 flammable liquid:

3.48 flammable gas or vapor:

3.51 grounded (earthed):

3.53 hazardous (classified) location:

3.54 hermetically sealed device:

3.57 ignition (autoignition) temperature (AIT):

3.58 ignition capable:

3.61 intrinsic safety:

3.62 intrinsic safety barrier:

3.66 intrinsically safe system:

3.68 liquid, combustible:

3.70 lower explosive limit (LEL):

3.80 maximum experimental safe gap (MESG):

3.90 powder filling:

3.102 seal, cable, explosionproof:

3.115 Zone 0 (IEC):

Area (location) classification

North American methods

Groups (NEC Article 500 / CEC Annex J18)

Groups (NEC Article 505/CSA C22.1 Section 18/IEC 60079-12/prEN 60079-12)

These groups are defined as:

Additional background information

Table 1 Temperature identification numbers

Maximum Surface Temperature

Table 2 Comparison of classification of flammable

Ethane, propane, butane,

Ethylene, coke oven gas,

Protection techniques for electrical apparatus in hazardous (classified)

Explosion confinement and flame quenching

Isolation from flammable atmospheres

Pressurization for Class II

Sealing (sealed device)

Inert gas filling

Energy release limitation

Other methods of protection