Universal Willem EPROM Programmer
Quick Start Guide
V1.1
1. Installation
1.1 Turn off the PC
1.2 Connect the DB25 parallel cable Male connector to PC’s printer port
1.3 Connect the DB25 parallel cable Female connect to Universal Willem EPROM Programmer
1.4 Plug in the USB cable to the PC USB port
1.5 Connect the USB Cable to the Universal Willem EPROM Programmer – the Green LED should
light up
1.6 Turn on the PC
1.7 Download the parallel port IO driver from-- www.driverlinx.com/ftp/unsupported/port95nt.exe
1.8 Install the drivers then restart your PC, run the utility and playaround with it a bit to get the DLL
and SYS file installed in the system and start a service.
1.9 Copy the programmer software 97g.zip from Floppy Disk into the Hard Disk
1.10 Unzip the file 97g.zip, all unzipped files should put in the same directory/folder
1.11 Double click the EpromM51 icon to start the program, then check the programmer type,
change it to PCB3 if it shows Willem.
1.10 Select Help from the main, then click Test Hardware. It should shows
Hardware Present in the status bar, otherwise please Check Power & connection
1
2. Jumper Setting
The Jumpers are divided into 3 Groups
2.1 Group 1 - For selecting different types of EPROM, EEPROM and Flash EPROM
2.2 Group 2 – For selecting 27xxx type EPROM programming voltage
2.3 Group 3 – Only for 4M or 8M memory chip
2
Once completed the Jumper setting, please follow the program instruction/hence to config the
DIP switch setting before programming any chip
3. Devices supported
27C64, 27C128, 27C256, 27C512, 27C010, 27C020, 27C040,27C1001
M27C1001, M27C2001, M27C4001
27C080 (A19) ,M27C801,M87C257
EPROM
2716(Vpp25V),2732, (adapter DIP24)
2764, 27128, 27256, 27512, 27010,
Vpp12.5V (21Vpp Modify Circuit)
28C65,28C64, 28C128, 28C256,28C512, 28C010, 28C020, 28C040
EEPROM M28C16A/17A (DIP28)
(Adapter or Jumper) 28C16,XLS2816 (DIP24)
28F64, 28F128, 28F256, 28F512,28F010, 28F020
MX26C1000, MX26C2000, MX28F1000, MX28F2000
Am28F256A, Am28F512A, Am28F010A, Am28F020A (New command
FLASH Memory
erase/prog.)
-- intel ---
i28F001BX, 28F004, 28F008, 28F016
29F64, 29F128, 29F256, 29F512,29F010, 29F020, 29F040, 29F080
FLASH Memory
29F001,29F002, 29F004, 29F008, 29F016, 29F032
24C02,24C04,24C08,24C16, 85C72, 85C82, 85C92
Serial (I2C) EEPROM
--- page write ----
24Cxx
24C32,24C64,24C128,24C256,24C512
<------ Data 8bit -----> (pin 6 ->ORG. [Schematic connect to
Microwire EEPROM GND])
93C06, 93C46, 93LC46, 93C56, 93C57,
3
93C66, 93C76, 93C86 (8bit), AT59C11, AT59C22, AT59C13
CAT35C102, CAT35C104, CAT35C108 (pullup pin7)
<------Data 16bit------> (pin 6 ->NC [No Connect])
93C06A ,93C46X,93C56,93C66,93C76,93C86 (NS)
16C84, 16F84, 16F84A ,16F627/16F628
12C508/A, 12C509/A, 12CE518, 12CE519, 16C505
16C620 16C621, 16C622, 16CE623, 16CE624, 16CE625, 16C710/711
MicroChip PIC
---ICSP connector----
16F870, 16F871, 16F872, 16F873, 16F874, 16F876, 16F877
PIC16F873A, PIC16F874A, PIC16F876A, PIC16F877A
AT29C256, AT29C512,AT29C010A, AT29C020, AT29C040,AT29C040A
W29EE512,W29EE011, W29EE012, W29C020(128),W29C040
Atmel Flash Memory PH29EE010(W29EE011)
(Sector Programming)
(Software Data Protection) ASD AE29F1008 (AT29C010), AE29F2008 (AT29C020)
Ver 0.992 up(DOS). Can run under win9x
(disable prog. CPUIdle or CPUCool)
Command seq. 5555/AA, 2AAA/55, 5555/A0
AT49F512, AT49F010, AT49F020, AT49F040
Atmel Flash Memory SST39SF010, SST3S9F020 ,SST39SF040
AT49Fxxx (Subset 29Fxxx) AT49F001,AT49F002 , AT49F008A
(Byte-by-Byte Programming)
(Software Data Protection) Command seq. 555/AA, 2AA/55, 555/A0
Am29F512, Am29F010, Am29F020, Am29F040,HY29F080
29F002, 29F002T, Pm29F002T
[Atmel] AT25010,020, 040 (A8-A0)
AT25080, 160, 320, 640, 128, 256 (A15-A0)
[ST] W95010....256, Microchip 25x010 - 25x640
--- Byte programming
Serial Peripheral Interface
25010,25020,25040
(SPI)
--- Page programming
EEPROM Mode0 (0,0)
25C080,25C160,25C320,25C640,25C128,25C256,25C512
AT25xxx, W95xxx
AT25HP256,AT25HP512
AT25HP1024 (24bit address)
-- CAT64LCxxx (16bit DATA IN/OUT) use Socket 93Cxxx
CAT64LC010, CAT64LC020, CAT64LC040
Atmel EEPROM (page prog.)
AT28C256, AT28C010, AT28C040
(Software Data Protection)
Nonvaltile SRAM (DS12xx) DS1220,DS1225Y, DS1230Y/AB, DS1245Y/AB, DS1249Y/AB
static RAM (Test RAM) 6116, 6264, 62256, 62512, 628128
EPROM winbond,SST W27E512, W27E010, W27C010, W27C020, W27C040
Electrical Erase Chip SST27SF256, SST27SF512, SST27SF010, SST27SF020
4
MX26C4000
Vcc = 3.3-3.6V SST37VF512, SST37VF010, SST37VF020, SST37VF040
Flash Memory SST,Sanyo SST28SF040A ,LE28F4001
Adapters
Atmel Auto Setect
AT89C51,52,55, AT89LV51,52,55
AT89S8252 (8K+2K), AT89S53, AT89LS8252,AT89LS53
AT89C1051,AT89C2051,AT89C4051 (20pin)
Atmel AT89Cxx (MCS-51) AT89C51RC (32KB), AT89C55WD (6.2V)
Adapter 32pin to MCS-51 SST89C54/58 (not fully support), SI89C52
Intel Auto Select
i87C51, i87C51FA, i87C51FB
------------------------------------------------
i8xC51,i8xC52,i8xC54,i8xC58 (tWP = 100uS*25 Pulse)
(read,write,erase,verify,checkempty,Lockbits ,Fusebits)
[Flash memory/EEPROM]
Atmel AVR 8-bit RISC AT90Sxxx
AT90S1200,AT90S2313
(Parallel programming)
90S2333, 90S4433, 90S4414, 90S8515, 90S4434, 90S8535
Adapter 32pin to MCS-51
reference AT90S2313 pin
Function Lockbit read AT90S2313 Errata Sheet.pdf
ROM (read/verify)
P8048AH, P8049AH,P8050AH, P8042AH Vea = 12V
P8041, P8042
MCS-48,MCS-41
OTP (read/verify/Progam)
Adapter 32pin to MCS-48/41
P8748,P8749H,P8742H Vea = 18V
EPROM (read/verify/Progam)
D8748,D8749,D8742,D8741, D8742 Vea = 18V
FLASH memory 8/16bit Am29F400,Am29F800,29F160,29F320 (read,write byte mode)
(Software Data Protection) HY29F200, HY29F400, HY29F800 , AT49F2048A, AT49F4096A,
</FONTAdapter (TSOP48) AT49F8192A
FLASH memory 8/16bit (Vpp12V)
i28F200,i28F400,i28F800,i28F160 (TSOP48)
(Software Data Protection)
28F001(DIP32 or PLCC32)
</BAdapter (TSOP48)
27C1024 (27C210), 27C2048 (27C2002), 27C4096 (27C4002),
EPROM 16bit (DIP40) (1-4Mbit) Schematic by Toomas Toots
Adapter Eprom 16bit (read,Program byte mode
Eprom only by use Resister pull up Data Bus (0xFF), A0 select low or high
byte)
5
M27C400(DIP40), 27C800, 27C160, 27C322
EPROM 16bit (DIP42) (4-32Mbit) Schematic by Toomas Toots
Adapter Eprom DIP42 (read,Program byte mode
Eprom only by use Resister pull up Data Bus (0xFF), A0 select low or high
byte)
FLASH memory 8/16bit
29LV200, 29LV400,29LV800,29LV160,29LV320 (read,write byte
(Software Data Protection)
mode)
Adapter (TSOP48LV)
-- Firmware Hub
82802AB, 82802AC, AT49LW040, AT49LW080
Firmware Hub / LPC FLASH SST49LF002A, SST49LF003A, SST49LF004A, SST49LF008A
Adapter Firmware Hub/LPC W49V002FA, W39V040FA
(PLCC32) (PP mode) (3.3V)
-- LPC flash
SST49LF020, SST49LF040
W49V002A, W39V040A
P28F002BC BOOT BLOCK FLASH MEMORY
Adapter P28F002BC (DIP40) - P28F002BC
6
4. Common used Flash Memory chip for PC Motherboard
VPP programming
IC Manufacture Part No. Memory Size
voltage
Am29F010 1M
Am29F002 2M
Am29F040 4M
AMD
Am28F010（A） 1M VPP=12.0 V
Am28F020（A） 2M VPP=12.0 V
Am28F040 4M VPP=12.0 V
AE29F010A 1M
AE29F020 2M
ASD AE29F040 4M
AE29F1008 1M
AE29F2008 2M
AT29C010A 1M
AT29C020 2M
AT29C040 4M
Atmel
AT49F001 1M
AT49F002 2M
AT49F004 4M
CAT28F001BX-T/B 1M VPP=12.0 V
CATALYST CAT28F010 1M VPP=12.0 V
CAT28F020 2M VPP=12.0 V
i28F001BX-T/B 1M VPP=12.0 V
Intel i28F010 1M VPP=12.0 V
i28F020 2M VPP=12.0 V
MX28F1000P 1M VPP=12.0 V
MX28F2000P/T 2M VPP=12.0 V
Macronix
MX29F001(N)T/B 1M
MX29F002(N)T/B 2M
F／V29C51001T/B 1M
Mosel-Vitelic
F／V29C51002T/B 2M
SST PH29EE010 1M
PH29EE020 2M
PH28SF040 4M
7
PH39SF010 1M
PH39SF020 2M
M28F256(A) 256K VPP=12.0 V
M28F512 512K VPP=12.0 V
SGS－THOMSON
M28F001 1M VPP=12.0 V
M29F002T／NT／B 2M
W29EE011 1M
W29C010 1M
Winbond
W29C020 2M
W29C040 4M
End
