03 01 Gold Exploration

Explor97 Master Page
Exploration
Geochemistry
Explor97 Contents
Paper 28
G
O
T
O
Author Index
Section Contents
Next Paper
Lithogeochemical and Mineralogical Methods

for Base Metal and Gold Exploration
Franklin, J.M.[1]
1. Geological Survey of Canada, Ottawa, Ontario, Canada
ABSTRACT
Specific criteria used for exploration for new ore may be derived from genetic models. These might include specific lithological assemblages, fractionation trends, alteration assemblages and ore-controlling structures, for example. Three lithogeochemical methods of use in exploration include: diagnostic petrogenetic trends, obtained from geographical or
statistical analyses of major and minor element data; diagnostic mineral assemblages, obtained through petrographic and
XRD analyses; and specific elemental signatures (gains, losses, and isotopic shifts), also obtained from analytical data.
Volcanogenic massive sulphide deposits formed from high-temperature metalliferous fluids generated in the sub-seafloor
through heating (from a subvolcanic intrusion) of downwelling seawater. Both the subvolcanic intrusions and related volcanic rocks have somewhat aberrant petrochemical trends, caused by unusually rapid heat removal to the hydrothermal system; extensive fractionation is evident in both major element and REE trends. Alteration includes lower semi-conformable
horizons, albite-epidote-actinolite-quartz zones, and under some deposits, broad carbonatized zones. Alteration pipes vary
from those with cores of Fe-chlorite and silica and rims of Mg-chlorite (after smectite), through Mg-chlorite core and sericite-rim pipes, to silica-sericite Fe-carbonate pipes. All are Na-, Ca- and Sr-depleted.
Lode-gold deposits are associated with major transgressive (typically high-angle reverse) fault zones. Vein systems typically
occur either in dilational jogs, near fault terminations, or at contacts between units with high ductility contrast. Regional
alteration is dominated by CO2 addition. Iron-dolomite and/or ankerite are most common near the deposits, but dolomite
or calcite form the regionally developed alteration assemblage. Sphene occurs distally, but rutile is common near vein systems. Sericite and albite or K-spar occur within a few tens of metres or less of the deposits.
Magmatic sulphide deposits formed by segregation of immiscible sulphide liquid from a parent mafic or ultramafic magma.
Deposits occur in intrusions and flows with unusually high Mg/Fe ratios. Nickel is depleted relative to Mg in fertile intrusions. Olivine in barren intrusions is rich in Ni, compared with fertile intrusions. Because sulphur saturation is promoted by assimilation of sulphur from an external source, Se/S ratios are higher in ore-bearing intrusions. Sulphur isotopes
may deviate strongly from mantle compositions because of assimilation, particularly in post-Archean intrusions.
INTRODUCTION
Conventional prospecting and airborne geophysical surveying will have
continued importance in finding new mineral resources, but exploration will become increasingly dependent on the application of geological principles, as well as advanced technology. Some regional and local
geological elements are critical to locating economic ore deposits: many
of these attributes indicate new ore potential, and thus are exploration
guides. The genetic model for each ore deposit type is based on extensive field observations, coupled with intensive petrochemical, mineralogical and isotopic investigations. Critical lithological assemblages,
specific fractionation trends, and diagnostic alteration assemblages are
examples of attributes that were originally documented during the quest

for genetic models, but have important application in exploration for
new ore. Before geological indicators of ore potential can be used, the
class of deposits being sought must be known. Knowledge is required,
prior to application of geologically based exploration tools, of those
essential attributes of any specific genetic model that are manifest either
by direct observation (i.e., maps or field studies) or laboratory analyses.
The choice of specific lithogeochemical and mineralogical exploration methods is dependent not only on choice of deposit type, but on
knowledge of the variability within each type. For example, the welldocumented mineralogical and chemical characteristics of alteration
associated with porphyry copper/molybdenum, epithermal gold and
In Proceedings of Exploration 97: Fourth Decennial International Conference on Mineral Exploration edited by A.G. Gubins, 1997, p. 191208
192
Exploration Geochemistry
volcanogenic massive sulphide deposits have been used very effectively

as an exploration tool for many years. Unique fractionation trends, the
presence of magmatic sulphide minerals, and anomalous Se/S ratios can
be applied in the search for magmatic sulphide ores. Subtle chemical and
mineralogical changes point the way to Mississippi Valley-type deposits.
Alteration associated with vein-gold deposits, however, has more limited application. For the latter deposit type, a good understanding of
structural control has proven to be the most useful tool in finding new
resources, particularly in established districts (see Robert and Poulsen,
this volume). For each, a brief review of the most commonly accepted
genetic attributes is followed by a description of petrogenetic indicators
of use in exploration.
VOLCANIC-ASSOCIATED
MASSIVE SULPHIDE DEPOSITS
Volcanic-associated deposits occur in terrains dominated by submarine
volcanic rocks: the deposits are typically in volcanic strata, but may also
be in or near sedimentary strata that are an integral part of a volcanic
complex. Volcanic-associated deposits contain variable amounts of economically recoverable copper, zinc, lead, silver and gold that were
deposited on or just below the paleo-seafloor, from high-temperature
(250400C), moderately saline (~35 wt.% NaCl) metalliferous fluid.
Their close spatial and genetic association with volcanic rocks has
prompted the use of the classification term Volcanogenic Massive Sulphide deposits, or VMS deposits as their most common acronym.
VMS deposits in the Precambrian occur as two compositional
classes, the copper-zinc and zinc-lead-copper groups (Franklin et al.,
1981; Franklin 1995). Phanerozoic deposits also include a copper-rich
category characterized by VMS deposits in mafic volcanic dominated
terrains (Large 1992). The copper-zinc deposit group has been further
divided into two types (Morton and Franklin, 1987): one typified by the
deposits in the Sturgeon Lake, Ontario area (Mattabi-type); and, the
other by deposits at Noranda and Mattagami Lake, Qubec. (Noranda
type). An important sub-group of the zinc-lead-copper deposits are Aurich VMS deposits (Poulsen and Hannington, 1996), which are typified
by Eskay Creek- and Boliden-type deposits. Each type displays distinctive compositional and alteration aspects. Consequently, mineralogical
and petrochemical criteria used as exploration guides must be sufficiently extensive to include all sub-types of deposits.
Some of the geological attributes (Figure 1) that are of use in exploring for VMS deposits include:
1. Presence of submarine volcanic strata: paleo-water depth controls
some variations in volcanic morphology, as well as alteration
assemblages and ore composition. Physical volcanological studies
provide useful information to help determine which assemblages
and compositions to expect.
2. Presence of a subvolcanic intrusive complex at shallow crustal
levels (ca 2 km). These can be any composition represented in the
overlying volcanic rocks, and generally: a) are sill complexes that
locally transect stratigraphy; b) are texturally variable, composite
intrusions, formed through multiple intrusions of the magmas at
the same crustal level; c) are [highly] variably fractionated, [with
reverse zonation common in] felsic intrusions containing abundant xenoliths of earlier mafic intrusions, with mafic portions more
abundant along their top (as irregular pods) and ends; or mafic
intrusive complexes that are commonly highly fractionated with
well-developed ferro-gabbro and granophyre phases; d) are devoid

of a significant metamorphic halo relative to intrusions emplaced at
deeper or drier crustal levels; e) are potential hosts to very lowgrade porphyry-copper zones that are superimposed on all rock
types; and f) may contain extensive sub-vertical breccia zones.
3. Presence of high-temperature reaction zones (one form of semiconformable alteration) within about 1.5 km of the subvolcanic
intrusions. Quartz-epidote-albite alteration, commonly mistakenly mapped as intermediate to felsic rocks, is prevalent under
many copper-zinc deposits.
4. Presence of laterally extensive carbonatized volcanic strata that are
depleted in sodium near deposits that formed in relatively shallow
water (< 1500 m, accompanied by explosion breccia, debris flows,
some subaerial volcanic products). These may represent the zone
where ambient seawater reacted with the upper part of the hydrothermal reservoir.
5. Synvolcanic faults that are recognizable because they: a) do not
extend far into the hanging wall of most deposits; b) commonly
contain discrete zones of alteration along their vertical extent;
c) are associated with asymmetric zones of growth-fault-induced
talus; and, d) may be locally occupied by synvolcanic dykes.
Virtually all of these faults formed in extensional tectonic regimes,
and may be listric. Some may be related to caldera margins, and
thus curvilinear; others may be margins of elongate axial summit
depressions (grabens), and subparallel to the axis of spreading
(Kappel and Franklin, 1989).
6. Alteration pipes may extend for thousands of metres in vertical
stratigraphic extent and are therefore mappable. The volcanic
rocks in virtually all pipes are sodium-depleted, but mineralogical
characteristics vary. Most commonly, rocks are silicified directly
under the deposits, with broader zones of sericite, Mg- and Fe-rich
chlorite or smectite. Less commonly, but important in many CuZn districts, the pipes may have intensely chloritized cores, with
more sericitic rims. Peripheral to the distinctive pipes, there is
commonly a broad zone of more subtly altered rock; smectite and
zeolite minerals may be important. Chemical changes in these latter alteration zones may be very subtle, requiring mineralogical or
isotopic studies to detect them.
Metamorphosed pipe assemblages are usually relatively easy to
recognize. Typically, rocks in Mg-Fe enriched pipes have been
recrystallized to anthophyllite and cordierite. Adjacent, less
intensely altered rocks may contain staurolite. Gahnite and Mnrich garnets may be important accessories. The relatively high ductility of altered volcanic rocks compared with their hosts resulted
in exceptional deformation in some districts. They may have
become detached completely from their related ore bodies.
7. Strata immediately above deposits may contain indications of mineralization. Hanging-wall volcanic rocks may contain alteration
pipe assemblages, most commonly sericite, or at least zeolitesmectite assemblages similar to the peripheral alteration associated with the pipes.
More importantly, hydrothermal precipitates such as ferruginous
chert, sulphidic tuff, and products of oxidation of sulphide mounds may be
sufficiently laterally extensive to be detected. Base metal contents within
these, although of sub-ore grade, may increase towards the deposits.
Franklin, J.M.
Table 1:
LITHOGEOCHEMICAL AND MINERALOGICAL METHODS
193
Summary of alteration indices to test for the presence of alteration.
Alteration Index
Element Ratios
Alteration Process
Source
Sericite Index
K2O / K2O + Na2O)
replacement of feldspar by sericite
Saeki & Date, 1980
addition of Fe and Mg as chlorite
Saeki & Date, 1980
Chlorite Index
MgO + Fe2O3 / (MgO + Fe2O3 + 2CaO + 2Na2O)
loss of CaO andNa2O by destruction feldspar

Spitz-Darling
Alkali Index
Hashimoto Index
Al2O3 / Na2O
Na2O + CaO / (Na2O + CaO + K2O)
MgO + K2O / (MgO + K2O + CaO + Na2O)
sodium depletion (Al2O3 conserved)
Spitz & Darling, 1978
loss of CaO and Na2O by destruction feldspar
Saeki & Date, 1980
addition of Mg and K as chlorite and sericite
Ishikawa, 1976
loss of CaO and Na2O by destruction feldspar
Date et al., 1983
Modified Hashimoto
FeO + MgO + K2O / (MgO + K2O + CaO + Na2O)
as above with addition of FeO
Coad, 1982
Hashigushi Index
Fe2O3 / (Fe2O3 + MgO)
addition of Fe as Fe2O3
Hashigushi, 1983
Residual Silica
SiO2 vs. Zr/TiO2 (silicification)
residual to feldspar fractionation line
Lavery, 1985
Pearce Element Ratios
molar Fe/Zr, Mg/Zr, Mn/Zr, K/Zr,CO2/Zr
addition of Fe, Mg etc. relative to conserved Zr
Stanley and Madeisky, 1993
molar (Na + K + 2Ca - Al/Zr) (alkali depletion)
molar (Si/Zr) - 7.5 Al/Zr + 6.25) (silicification)
Other
e.g. Zn/Na2O
e.g., sphalerite staining and sodium depletion
Normative plots
e.g. corundum > .1%, feldspar ratio
Alkali depletion, other
Mass Balance plots
All major and trace elements, altered vs. unaltered
Addition, loss, metasomatism,

volume/mass changes vs. unaltered sample,
immobile elements
Petrochemical trends
Recent studies of hydrothermally active sites on the modern seafloor
(Embley et al., 1988; Franklin 1996; Hannington et al., 1995) as well as
research on subvolcanic and related volcanic rocks associated with
ancient deposits (Campbell et al., 1982), have demonstrated the presence of very specific, and possibly unique petrochemical trends that are
related to the ore-forming process. Galley (1995) has summarized many
of the lithogeochemical methods that are useful exploration tools. Many
alteration indices have been developed to test petrochemical data for the
presence of alteration (Table 1). While these are useful and simply
applied, in many cases, mineralogical data are equally sensitive, and
more easily applied (particularly in the field) indicators of ore potential.
As described above, an important constituent of the hydrothermal system is the heat source, commonly represented by a subvolcanic intrusion. Compositional variations within these intrusions and their
associated volcanic rocks can be affected by the presence of a hydrothermal system in two ways: the rapid removal of heat can cause unusual
fractionation to occur within the subvolcanic intrusion, and secondly,
hydrothermal fluid may enter into the melt. Hydrothermal signatures
are developed through assimilation of previously altered wall rocks.
Fracture-controlled alteration is generally sub-solidus and occurs after
approximately 80% crystallization (Norton and Knight, 1977).
The presence of anomalously fractionated basaltic sequences has
been documented on the Galapagos Ridge (Embley et al., 1988) and at
Cyprus (Schmincke et al., 1983). In both cases, fractionation has proceeded from N-MORB through ferrobasalt, Fe-Ti basalt to andesite
Gresens, 1967
Grant, 1986
Baumgartner & Olsen, 1995
(Figure 2). Sulphur and the volatile contents increase with amount of
fractionation, although sulphur decreases remarkably in the
end-member andesite. Efficient removal of olivine and immiscible-sulphide droplets into the base of shallow magma chambers has occurred
during fractionation.
Fractionation [has] may also have affected shallow-level felsic subvolcanic magma chambers, as at Sturgeon Lake (Beidelman Bay intrusion) and Noranda (Flavrian intrusion). Rapid removal of heat may
have forced disequilibrium crystallization, causing early formation of
anomalous amounts of Ca-plagioclase and ferromagnesian minerals.
Irregularly disposed mafic portions of these intrusions are common
near their stratigraphic top and lateral terminations. Removal of Cafeldspar from the melt, or complexing of Eu during catastrophic ingress
of seawater could [has] result[ed] in depletion in europium relative to
other REEs (Campbell et al., 1982) forming a distinctive REE pattern
(Figure 3). However, europium depletion may also be associated with
hydrothermal alteration of these high-level complexes.
Although virtually no data exist on the Cl contents of ancient
sequences, these data may be useful indicators of the potential for hydrothermal activity to have occurred in an area. Recent data on the Sr isotope and Cl contents of the various members of the fractionated suite at
Galapagos indicate that these melts were likely progressively contaminated by seawater. This could have been caused either by assimilation of
old crust or ingress of hydrothermal fluid into the melt. Cathles (1990)
suggested that the latter process may be important in forming large
hydrothermal systems. However, the Galapagos suite could also be the
result of progressive melting of previously altered oceanic lithosphere.
194
Figure 1: Composite section through a volcanogenic massive sulphide system. Note locally advecting seawater near the deposit, which could form a Nadepleted, Mg-enriched alteration zone. The scale of this alteration depends on the longevity of the system, as well as the physical nature of the footwall rocks.
Figure 2: Fractionation index of seafloor basalt near active spreading ridges. Note the high values and relatively narrow range of Mg numbers (Mg/Mg
+ Fe) for basalts not associated with VMS deposits (Northern Rift Zone), compared with the large range and low values for those rocks associated with
deposits (Horst and southern rift zone).
Alteration beneath Cu-Zn massive sulphide deposits

Alteration has been studied more extensively than most attributes of
these deposits. Alteration mineral assemblages and associated chemical
changes have been very useful exploration guides. Alteration occurs in
two distinct zones beneath these deposits (see Figure 1).
1. Alteration pipes occur immediately below the massive sulphide

zones; here a complex interaction has occurred among the immediate sub-strata to the deposits, ore-forming (hydrothermal) fluids
and locally advecting seawater; and,
Franklin, J.M.
Figure 3: Composite REE patterns for felsic rocks in Archean sequences.

Note that the range of patterns displaying a prominent negative Eu*
anomaly is associated with massive sulphide deposits, the relatively flat
pattern with barren areas.
Figure 5:
Figure 4:
pipe.
195
Composite characteristics of a Noranda-type alteration
Composite characteristics of local and regional alteration associated with massive sulphide deposits formed in shallow-water (< 2 km).
2. Lower, semi-conformable alteration zones (Franklin et al., 1981)

occur several hundreds of metres or more below the massive sulphide deposits, and may represent in part the reservoir zone
(Hodgson and Lydon, 1977) where the metals and sulphur were
leached (Spooner and Fyfe, 1973) prior to their ascent to and
expulsion onto the sea floor.
Under Precambrian deposits formed in relatively deep water
(Noranda-type), alteration pipes typically have a chloritic core, surrounded by a sericitic rim (Figure 4). Some, such as at Matagami Lake,
contain talc, magnetite and phlogopite. The pipes usually taper downwards within a few tens to hundreds of metres below the deposits to a
fault-controlled zone less than a metre in diameter, but may extend for
over 2000 m below the deposits, particularly in the Noranda type.
Volcanological evidence suggests that some Noranda-type deposits
formed in less than 1000 m of water as hydrothermal explosion breccias.
The main differences between Noranda- and Mattabi-type deposits are
rock composition and permeability, although the latter were most certainly shallow water deposits.
Beneath deposits formed in shallow water (Mattabi-type), the pipes

are silicified and sericitized; chlorite is subordinate and is most abundant on the periphery of the pipes. Aluminosilicate minerals, such as
pyrophyllite and andalusite, are prominent (Figure 5).
Alteration pipes under Phanerozoic Cu-Zn deposits are similar to,
but more variable than those under their Precambrian counterparts. For
example, Aggarwal and Nesbitt (1984) described a talc-enriched
alteration core, surrounded by a silica-pyrite alteration halo, beneath the
Chu Chua deposit in British Columbia. The Newfoundland, Cyprus,
Oman and Galapagos Ridge deposits have Mg-chlorite in the peripheral
parts of their pipes, together with illite. Iron-chlorite, quartz and pyrite
typify the central parts of the pipes.
Virtually all alteration pipes are characterized by Na depletion. Base
metal additions are also ubiquitous, although highly variable in scale.
The alteration pipes under deposits such as Millenbach and Ansil extend
stratigraphically downwards for hundreds of metres, and contain abundant chalcopyrite. Under Mattabi, however, only a few metres of the
footwall contains abundant chalcopyrite. As noted above, chlorite spe-
196
cies varies considerably; the well-known Mg addition under some

deposits is by no means a common feature under many other deposits.
At Mattabi, for example, Mg is depleted in the footwall (Franklin et al.,
1975), but Fe and Mn are enriched. Enrichment in Mn occurs only where
syn-depositional carbonate alteration is prominent in the footwall.
The lower semiconformable alteration zones have been recognized
under deposits in many massive sulphide districts (Galley, 1993). These
include laterally extensive (several kilometres of strike length) quartzepidote zones, several hundred metres thick, that extend downwards a
few hundred metres stratigraphically below the Noranda, Matagami,
and Snow Lake deposits of the Canadian Shield. Zones of epidote, actinolite and quartz in the lower pillow lavas and sheeted dykes of the ophiolite sequences at Cyprus (Gass and Smewing, 1973) and in East Liguria,
Italy, were explained by Spooner and Fyfe (1973) as due to increased
heat flow as a result of convective heat transfer away from the cooling
intrusions at the base of these sequences. All of the epidote-quartz zones
are depleted in copper, zinc and sulphur (e.g., Skirrow and Franklin,
1994). They represent the zone of high temperature hydrothermal reaction (ca. 400C), under low water-rock ratio conditions, where the metals and sulphur entered into the ore-forming solution (Richards et al.,
1989; Spooner 1977; Spooner et al., 1977a,b).
The albite-epidote-quartz alteration zones are generally metaldepleted. Skirrow and Franklin (1994) show that virtually all of the
copper, and one-third of the zinc, has been removed from the albiteepidote-quartz zone in the footwall to the Snow Lake (Manitoba) deposits. Silica and calcium were added, and magnesium was lost. MacGeehan
and MacLean (1980) illustrate similar changes for the footwall sequence
at Matagami Lake, Qubec.
Zones of alkali-depleted, variably carbonatized strata occur directly
beneath some deposits (e.g., Mattabi-type deposits, Hudak, 1996).
These may extend up to tens of kilometres along strike, and occur in the
upper few hundred metres of the footwall (paleo-seafloor) (Figure 6).
These zones [probably represent] acted as a sealed cap to the hydrothermal reservoir, and formed through progressive heating of downward
percolating seawater, with some possible input CO2 from an underlying
magma chamber, or by pyrolysis of organic compounds in the footwall.
The distinctive change in carbonate species provides a very important exploration guide. Franklin et al. (1975) and Morton et al. (1990)
Figure 6: Regional distribution of carbonate alteration in the Sturgeon

lake district, Ontario. Carbonate is shown with C symbols. The carbonate-bearing rocks are usually Na-depleted.
have shown that on a regional basis, calcite has been added to the felsic
strata, and Fe-dolomite to mafic strata (see Figure 5) in the Sturgeon
Lake, Ontario, area. Siderite occurs immediately below and within a few
hundred metres of deposits, whereas Fe-dolomite and calcite occur farther away from the deposits. Although the total CO 2 content of the rocks
remains essentially unchanged (about 510% of the rock), the high Fe
content of the mineralizing fluid that passed through these rocks converted the earlier-formed Ca and Fe-Mg-Ca carbonates to siderite. Concomitantly, Mn was incorporated into the siderite. Data on carbonate
nodules that are presently forming under the deposits at Middle Valley
and Escanaba Trough confirm this transition.
The alkali depletion that is common in many alteration zones is
manifest as abundant aluminosilicate minerals (andalusite and, less
commonly, kyanite) in areas of abundant carbonate alteration. In the
absence of carbonate, margarite (at Snow Lake; Zaleski, 1989) and chlorite replace the feldspar.
Amphibolite-grade metamorphism significantly changes the alteration assemblages under VMS deposits. At upper greenschist facies,
chloritoid forms in the carbonatized alteration zones. Although Mgchlorite remains stable well into amphibolite facies, Fe-chlorite has
changed to staurolite in districts such as Snow Lake, Manitoba (Walford
and Franklin, 1982) and Manitouwadge (Friesen et al., 1982). In very
Fe-rich rocks (and in the absence of potassium) anthophyllite is abundant (Froese, 1969).
The mica species in alteration pipes are poorly documented. At Mattabi, although sericite is the most abundant mica, paragonite is common
(but difficult to recognize), even in Na-depleted rocks.
Alteration beneath Zn-Pb-Cu deposits

Alteration associated with Zn-Pb-Cu deposits is typified by that in
the Hokuroku district of Japan (Figure 7). Canadian deposits, such as
those at Buchans, Newfoundland, Chisel Lake, Ontario, and the Buttle
Lake, British Columbia districts, have similar alteration patterns to
Hokuroku deposits and those in the Tasman Geosyncline, Australia
(Gemmell and Large, 1992). Lower semi-conformable alteration
zones (cf. Cu-Zn deposits) are well documented under the Bergslagen
(Sweden) and Iberian VMS districts.
Four alteration zones (Figure 7) in the Hokuroku district have been
described by Shirozo (1974), Iijima (1974), and Date et al. (1983). The
most intense zone of alteration, zone four, is immediately below the
deposits, and consists of silicified, sericitized rock, with a small amount of
chlorite. Zone three contains sericite, Mg-chlorite, and montmorillonite,
and is not silicified. Feldspar is absent from zones three and four. Zone
two consists of sericite, mixed-layer smectite minerals, and feldspar.
Zone one contains zeolite (typically analcime) as an essential mineral,
with montmorillonite. Outside these four zones the volcanic rocks have
been affected by deuteric alteration, which formed clinoptilolite and
mordenite. Metamorphism and deformation obscure the alteration minerals associated with zones 1 to 3. At Buttle Lake, for example, zone four
alteration is most prominent; carbonate is also present, and is also present
distal to the Hokuroku deposits. Although chlorite is much less abundant
under Zn-Pb-Cu deposits than under Cu-Zn deposits, the alteration pipe
under the Woodlawn deposit (Tasmania) is very chloritic (Peterson and
Lambert, 1979). Alteration under the sediment-associated deposits of
this group consists of locally distributed sericite-quartz; many deposits
do not have obvious alteration zones.
Franklin, J.M.
Figure 7:
197
Mineral zonation associated with Zn-Pb-Cu deposits (Kuroko type). After Iijima, 1974. For descriptions of zones see text.
Figure 8: Harker diagram illustrating Na and K metasomatized felsic volcanic compositions in the ergslagen district. Infilled circles represent normal felsic
compositions, with K-enriched rocks from the upper part of the semiconformable alterations zone to the right, Na-enriched rocks from the lower zone to the left.
Semi-conformable alteration beneath Zn-Pb-Cu deposits occurs on

a very large scale, and thus may be easily misinterpreted. Galleys (1993)
review describes the Bergslagen district as having a broad zone of
quartz-microcline, K-enriched alteration, known locally as leptite, with
associated K enrichment, underlain by Na-enriched zones. These have
been shown by Bromley-Challenor (1988) to lie outside the normal
compositional range of volcanic rocks (Figure 8).
In the Iberia district, Munha et al. (1980, 1986) have shown similarly
K- and Na-enriched rocks that were originally classified as spilites or
keratophyres. The latter two terms may actually be misrepresentations
of primary igneous compositions, and might be applicable only to alteration systems. Munha et al. (1980) showed that the most permeable
volcanic strata contain intensively altered rocks, with K-feldspar,
smectite-chlorite, zeolite and Mg-carbonate near the top, and albitechlorite-epidote (or, deeper albite-chlorite-epidote-actinolite) assemblages at lower stratigraphic positions. These latter zones are similar to
those in the Snow Lake, Manitoba district (Skirrow and Franklin, 1994).
Syndepositional indicators of ore potential

Many massive sulphide districts have sedimentary or distal, syndepositional strata that reflect the ore-forming process. For example, the
various sulphidic tuff horizons at Noranda (Kalogeropoulos and Scott,
1983, 1989), and at Bathurst (Peter and Goodfellow, 1996), the Key Tuffite horizon at Matagami Lake (Davidson, 1977), the ochre at Cyprus
198
(Herzig et al., 1991), and the shale beds associated with several deposits
(Kidd Creek, Uchi, West Arm) were all deposited penecontemporaneously with VMS deposits, or slightly pre-date them. Some exhalites have
no apparent relationship with known VMS, and represent a period of
extensive, but shallow, low temperature hydrothermal convection. Modern sea-floor hydrothermal sites also have hydrothermal sediments surrounding them (Hannington et al., 1990). Finally, many VMS deposits
have thin, laterally extensive tails leading away from the economic sulphide deposits; these may extend for hundreds of metres or more. They
usually contain sub-economic metal contents; most are composed of
barren pyrite.
The near-field sedimentary strata may be divided into two groups;
those that contain sulphide as at least an accessory mineral, and those
that contain oxide minerals. The origin of each of these is somewhat
complex. Sulphidic sediments may have incorporated fallout particles
from hydrothermal plumes. They may also have formed from the discharge of poorly focussed low-temperature hydrothermal fluids in areas
surrounding the high temperature vents. The oxide zones may be
formed from the oxidation of sulphides (Hannington et al., 1990; Kalogeropoulos and Scott, 1983), or by direct precipitation of oxide minerals
(i.e., iron formation).
The geochemical aspects of these two types of deposits that pertain
to exploration have only been examined in a few districts. Some preliminary findings are as follows.
For sulphidic sediments:
1. Base metal contents increase towards the ore zone, although rather
irregularly (Kalogeropoulos and Scott, 1989).
2. The silver contents of disseminated sulphides in any type of VMSrelated sedimentary rock are higher than in pyrite from strata
where the sulphide was generated biogenically (Elliot, 1984). At
Kidd Creek, for example, disseminated sulphide in the hangingwall graphitic shale unit contains 60 ppm Ag, in comparison with
the silver content of pyrite from unmineralized black shale of
18 ppm. Pyrite from VMS-related sedimentary rocks also has
lower Ni and Co contents (200 and 120 ppm, respectively) than the
abundances in biogenic pyrite (2000 and 650 ppm).
3. The sulphur isotopic composition of sulphides in sediments associated with Precambrian VMS mineralization typically has a very
narrow range ( 1), clustered around 0, in contrast to sulphides in shale not associated with VMS deposits, which are probably biogenic (Goodwin et al., 1976), and have very wide ranges
(typically 8 to +8).
For oxide-rich sediments derived through degradation of VMS sulphides, only a few indicators are noteworthy.
1. Hannington et al. (1988) have demonstrated that gold is enriched
by a factor of 10 to 100, by a secondary process in the oxidized sulphidic sediments at the TAG field (Mid Atlantic Ridge) and in the
ochres at Cyprus (Herzig et al., 1991). This enrichment may only
be present where bottom water was oxidizing, i.e., in Phanerozoic
open-ocean areas.
2. The lead isotope composition of oxidized sulphide material is conserved from the primary deposit composition, and is much less
radiogenic than the lead in oxides generated by weathering of ferruginous (non-sulphide) rocks, or from iron formation (Gulson
and Mizon, 1979).
LODE-GOLD DEPOSITS
Lode gold deposits occur in close association with major deformation
zones, and can occur in virtually any rock type (Keays et al., 1989). The
general characteristics of Archean examples of this deposit type have
been summarized by Kerrich (1983), Colvine et al. (1988), Card et al.
(1989) and Robert and Poulsen (this volume). Lode gold deposits occur
in sequences of all ages, although they may be more plentiful in Archean
rocks; Superior Province has produced 142 million ounces of gold, only
surpassed by the paleoplacer deposits of the Witwatersrand (Card et al.,
1989). Otherwise their geological characteristics are similar regardless
of age.
The lode-gold group of deposits includes both vein and disseminated (or sulphidic schist) types. These two types account for the majority of the gold produced in Canada. They are associated with major fault
zones, and are themselves structurally controlled. They appear to form
very late in the geological history of their regions, typically after the peak
of metamorphism.
Some geological attributes useful for exploring for this deposit type
(after Poulsen, 1996; Robert, 1996) are:
1. Areas containing significant volumes of mafic volcanic rocks and a
major fault zone, especially near the edge of a volcanic domain are
most favourable. Shear zones or faults demonstrating high-angle
reverse to reverse oblique motion contain the largest deposits
(Sibson et al., 1988).
2. Gold deposits do not normally occur in the first-order fault or
shear system, but in subsidiary fault and shear zones.
3. Favourable segments of fault or shear zones are those intersecting
favourable host rocks such as small felsic intrusions, iron formations, and iron-rich rocks. Also, portions of a shear or fault system
where splays or deviations from the overall trend are evident are
more productive.
4. Rocks surrounding the deposits are commonly (but not ubiquitously) carbonatized.
Petrochemical trends
As gold deposits formed well after nearly all of their host rocks, little
if any information on the petrogenesis of these rocks has relevance to the
deposits. A hypothesis has been presented (e.g., Callan and Spooner,
1989) for a genetic relationship between the tonalitetrondhjemitegranodiorite magmatic assemblage and gold deposits. The isotopic data
used in their argument do not provide a unique resolution of this
hypothesis. Although the common association of small albitic porphyry
intrusions with gold deposits also provides some possibility for a genetic
relationship, age data (Anglin et al., 1988; Marmot and Corfu, 1989),
as well as petrogenetic arguments (the porphyry bodies usually pre-date
the metamorphic peak, the veins postdate it; Robert, 1996) make any
genetic relationship virtually impossible.
Rock et al. (1989) and Wyman and Kerrich (1989) noted the association of gold deposits with shoshonitic (typically lamprophyric) intrusions. Although no direct genetic (or temporal) connection with this
magmatic suite has been confirmed, the age of these intrusions is similar to ages determined for some gold veins (Bell et al., 1989). This similarity may reflect some common source attributes for gold-bearing
fluids and alkaline rocks, but no more direct genetic relationship has
been established.
Franklin, J.M.
Alteration
Alteration associated with gold deposits has a very complex genesis.
Only a few diagnostic features have been observed, and these must be
treated with some caution (Fryer and Franklin, 1982).
Alteration is caused by two processes.
1. Dynamo-thermal alteration, usually on a regional scale, accompanied the formation of most major shear and fault zones. Feldspar
destruction (yielding a mica) was commonly accompanied by
dissolution of some components, leading to volume loss within a
shear zone (Beach, 1976). Alkali elements may have been gained,
through mica formation, or lost, through feldspar destruction.
Typically, ferromagnesian components are conserved. Fluid movement through shear zones caused hydration, and possible resetting of isotopic systems. All of these alteration processes can
combine to yield a geochemical signature with no relevance to the
ore-forming process. Almost any shear zone will be mineralogically
and chemically modified; caution must be exercised in using these
changes to determine ore potential.
2. Ore-related fluid movement through the area of gold mineralization imparted mineralogical and geochemical change at two scales
(Figure 9). Many aspects of alteration associated with gold deposits
are reviewed by Colvine et al. (1988).
3. At a local scale, sulphidation, alkali (either K or Na) and carbonate
metasomatism, boron enrichment, and hydration are very common. The scale of alteration is typically from a few centimetres to
a few metres adjacent to veins. The area affected by alteration is
controlled by the fracture-induced permeability of the rocks. Per-
Figure 9:
199
vasive alteration is present in schistose deformation zones, but

much more defined (and possibly equally extensive) alteration is
observed adjacent to extensional veins. For example, at the Doyon
Mine (Guha et al., 1982) vein and disseminated gold mineralization occurs within a broad envelope of highly sheared, sericitized
volcanic rocks. In contrast, Robert and Brown (1986) documented
very well defined alteration zones, typically a few metres wide,
adjacent to the veins at the Sigma Mine.
Mass balance studies (Robert and Brown, 1986; Ames et al., 1991;
Dub 1990; Clark et al., 1989; Kerrich, 1983) yielded results that demonstrate a lack of consistency in alteration styles for lode gold deposits.
A few generalities can be drawn.
1. The complexity of chemical gains and losses increases as the orebearing veins are approached.
2. Alteration mineral assemblages, as well as chemical gains and
losses, are furthermore a function of pre-alteration mineral assemblages. The latter generally reflect the primary rock type, but
metamorphic modification of the pre-ore mineral assemblage can
significantly affect the final alteration assemblage. For example, an
ultramafic rock that was already converted to a talc-chlorite assemblage will react quite differently during alteration in comparison
with a rock composed of olivine, pyroxene and plagioclase.
3. Either Na2O or K2O (but rarely both) are the most extensively
added components. K2O addition is most common. Sericite and
biotite are common alteration minerals, particularly, but not exclusively in disseminated-type deposits. Paragonite may also be
present (Ames et al., 1991). Albite or K-feldspar is more common
adjacent to veins which occupy brittle fractures. At Hemlo, how-
Schematic illustration of alteration associated with lode-gold deposits.
200
ever, K-feldspar (microcline) is extensively developed around the
ore (Kuhns, 1986), with sericite alteration peripheral to the microcline zones.
Elemental additions most diagnostic of gold mineralization are (in
approximate order of importance) Au, S, CO2, K, Rb, SiO2, Na, As,
Sb, W, B, Mo and Pb (Davies et al., 1982; Andrews et al., 1986 and
references therein). A few elements, notably Ca and Sr, may be
depleted, due to feldspar destruction. Given that volume reduction
may have occurred during deformation, some immobile elements
(e.g., Al2O3, TiO2, Zr) display apparent increase, but mass balance
calculations may confirm that such changes occur through volume
or mass change, rather than real gain or loss. The size of geochemically anomalous zones of these elements is variable, from centimetres to hundreds of metres away from ore. Typically, the zones of
geochemically measurable alteration are about the same width as
the ore deposits themselves, and are symmetrical to the ore zone.
4. Sulphide minerals (commonly pyrite) typically have overgrown

and replaced ferromagnesian minerals. Iron was added at the Victory Mine (Clark et al., 1989), but sulphidization was prominent at
the San Antonio and Norbeau deposits (Ames et al., 1991; Dub
1990). Sulphidization is probably a particularly important indicator of gold mineralization, as reduction in the sulphur content of
the gold-bearing fluid probably destabilized the Au-bisulphide
complex, inducing very efficient deposition of gold.
Pyrite (or, less commonly pyrrhotite) is most abundant where
gold-bearing fluids have interacted with iron-rich rocks. Sulphidized iron formation (e.g., Geraldton, Ontario; Anglin and
Franklin, 1986) and sulphidized Fe-basalt are important hosts to
gold mineralization. As noted by Kerrich et al. 1977), the Fe2+/Fe3+
ratio increases towards gold veins, largely in response to pyrite formation.
5. Alumina appears to have been mobile on a very local scale. Silicification is most common in broad shear zones, where silica-sericitepyrite alteration assemblage typifies many disseminated-type
deposits.
6. Tourmaline, scheelite, and arsenopyrite are all locally abundant in
some deposits. In addition, very minor amounts of base metal sulphides occur in some veins; molybdenite and chalcopyrite seem
most common, but sphalerite and galena are recorded at several
deposits (Hodgson and MacGeehan, 1982). Virtually none of these
minerals is sufficiently abundant to provide an indication of ore
potential, although all may occur as weathered and transported
products in overburden.
Regional scale alteration is well developed in some districts, such as
Timmins (Davies and Whitehead, 1982), Red Lake (MacGeehan
and Hodgson, 1982), and Geraldton (Anglin and Franklin, 1986),
less well developed at Bissett (Ames et al., 1991), and not prominent or even absent at others, such as Hemlo, and the Thompson
BousquetDoyon (Malartic) group of deposits. Apart from shearrelated mica alteration that may be widely distributed, depending
on the breadth of any particular shear zone, the principal alteration
type is carbonatization.
Carbonate alteration has been intensively examined at the Victory
Mine area in Western Australia (Clark et al., 1989), the Timmins district
(Davies et al., 1982), the Chibougamau area (Dub, 1990), Red Lake
(Andrews et al., 1986) and Bissett, Manitoba (Ames et al., 1991).
Summarizing their work, the principal changes at a regional scale are

as follows:
1. Virtually all rock types are affected by addition of CO2 only. Other
components of the carbonate minerals are derived through metasomatic alteration of the host rock.
2. The species of carbonate mineral present is a function of both the
mole fraction of CO2 (X CO2) of fluids and the pre-alteration mineral assemblage. Clark et al. (1986) demonstrated at the Victory
mine in the Yilgarn Block of Western Australia that close to the
mineralization, ferruginous dolomite/ankerite is the prevalent carbonate species, whereas further from the deposit, calcite predominates. Significantly, silicate and oxide assemblages also reflect
varying amounts of alteration. The equations presented by Clark et
al. (1986) and Ames et al. (1991) are instructive. These represent a
progressive set of reactions, describing the effect of an H2O-CO2
fluid on a metagabbro or metabasalt. They are written here in generalized form:
In metagabbro, the reactions are (Ames et al., 1991):
At a scale of tens of metres or more away from the vein systems, two
reactions describe the principal changes:
actinolite + epidote + CO2 + H2O
chlorite
+ calcite + quartz [1]
The specific reaction affecting titanite to form leucoxene produces a

mineral assemblage that is readily visible:
titanite + CO2
calcite + rutile + quartz
[2]
At a scale of 25 m away from the veins, ankerite appears in the alteration asemblage:
chlorite + calcite + CO2 + albite
ankerite
+ paragonite + quartz [3]
Immediately adjacent to the veins (~0.5 m), K is added:

paragonite + quartz + K+
muscovite + albite
[4]
In gabbroic rocks where potassium was added (either from the altering fluid or prior to carbonatization), the reactions described by Clark
et al. (1986) pertain:
On a regional scale (10s or more metres):
amphibole + epidote
+ H2O + CO2 + K2O
sphene + CO2
biotite
+ chlorite + calcite + quartz
rutile + calcite + quartz
[5]
[6]
With increasing X CO2 (i.e., closer to the veins):

biotite + chlorite
+ calcite + CO2
dolomite
+ muscovite + quartz + H2O
[7]
The important aspects to note are the presence of rutile (rather than
sphene) as a result of CO2 metasomatism, and that with increased
X CO2, the biotitechloritecalcite assemblage produced in reaction [5])
Franklin, J.M.
changes to dolomitemuscovitequartz (reaction [7]). Knowledge of the
titanium mineral species, as well as the mica species and carbonate composition can provide some estimate of closeness to a gold-bearing
(hopefully!) system of conduits (i.e., faults/shear zones). This type of
mineral determinative work can be done by x-ray diffraction, an inexpensive and rapid method. The carbonate species can effectively be
determined by staining methods.
Discriminating Au-related from VMS-related alteration

As noted above, both vein-gold deposits and VMS deposits may have
significant carbonate alteration associated with them. How does the
exploration geologist, confronted with carbonate alteration in the field,
determine which deposit type is likely to be associated with the alteration? Besides the obvious field criteria (structural observations,
regional setting), the answer lies in understanding the processes of alteration. As demonstrated above in the discussion of vein-gold related
alteration, the carbonate species are formed through a metasomatic process, where only CO2 is added to the rock. The other constituents of the
carbonate minerals were derived from the host rocks, and thus the species is to some extent a function of host-rock composition. Carbonate
alteration associated with massive sulphide mineralization was derived
entirely from the hydrothermal fluid. All constituents were added to the
rock, and metasomatism was probably unimportant.
In order to discriminate between these types of mineralization, mass
balance studies should be undertaken. Using complete whole-rock analysis (including volatile elements), preferably with specific gravity measurements (not necessary if using Grants (1986) method), it is necessary
to simply determine whether only CO2 was added to the rock (and
therefore vein-gold mineralization is likely present) or all of the carbonate constituents were added (Fe, Mg, Ca as well as CO2), indicating the
potential presence of hydrothermal-exhalative (VMS or possibly epithermal) type of mineralization. A similar approach for sulphur should
also work, and could be used as corroborating evidence.
201
MAGMATIC SULPHIDE DEPOSITS

Magmatic sulphide deposits form by the segregation of an immiscible
sulphide liquid from a parent silicate magma. The magma is generally of
mafic or ultramafic composition and the elements of economic interest
which concentrate in the molten sulphide include nickel, copper, cobalt
and the platinum group elements (PGEs). The most important examples
of this category in Canada are the world class deposits at Sudbury,
Ontario and in the Thompson Nickel Belt in Manitoba. Other significant
deposits occur at Shebandowan and Timmins in Ontario, Lynn Lake in
Manitoba, and the Ungava belt in Qubec.
A number of lithogeochemical approaches have been suggested for
the exploration for magmatic sulphide deposits (Lesher and Stone,
1996) but few of these have found wide application. Probably the most
useful application of lithogeochemistry has been in the delineation of
the stratigraphy within igneous intrusions or sequences of volcanic
rocks. Lithogeochemistry can also be used as a direct indicator of the
presence of magmatic sulphides but these methods require more
research and development before they can be used routinely.
Delineation of igneous stratigraphy

Magmatic sulphide deposits are, by definition, syngenetic with the
igneous bodies in which they occur. Sulphides segregate at specific times
during magmatic differentiation and are therefore associated with particular phases or stratigraphic units within an intrusion or volcanic succession. While these units are normally defined on petrographic criteria
including mineralogy and texture, their chemical compositions are
often more distinctive than subtle petrographic differences. Moreover,
petrographically homogeneous units commonly display significant
compositional variations (i.e., cryptic variation). Finally, ultramafic
rocks in particular are very susceptible to alteration, which may completely obliterate any primary minerals and texture, leaving lithogeochemistry as the primary means of identifying the protolith.
Figure 10: Schematic cross section of a typical Kambalda ore shoot showing the MgO contents of the ore-bearing and barren komatiite units (after
Lesher and Groves, 1984).
202
For these reasons alone, lithogeochemistry should form part of any

exploration program for magmatic sulphide deposits. The compositional parameters which will be most useful will depend on the circumstances in each case. However, as a general rule, some attention should be
given to defining a differentiation index. For example, in mafic and
ultramafic rocks where fractional crystallization of olivine and pyroxene
is a dominant differentiation process, the magnesium number (the magnesium number, sometimes abbreviated as Mg# or mg, is simply the
atomic ratio Mg/(Mg+Fe)) is frequently used for this purpose. In the case
of ultramafic volcanics (komatiites), the absolute MgO content, recalculated on a volatile-free basis, serves as a practical differentiation index.
Komatiite-associated nickel sulphide deposits provide one of the
best examples of the use lithogeochemistry for this purpose. These
deposits are associated with extrusive komatiites in Archean greenstone
terranes in Australia, Canada and Zimbabwe. Gresham and Loftus-Hills
(1981) give an excellent review of the characteristics of deposits in the
type area of Kambalda, Western Australia. The sulphide accumulations
occur in the lower parts of thick komatiite sequences with the bulk of the
ore occurring at the base of the lowermost flow-unit. The ore-bearing
units average 50 m but may exceed 100 m in thickness whereas flows in
the lower part of the sequence but remote from ore are typically 1520 m
thick. The ore-bearing and barren flow units are also compositionally
distinct. The thick basal flows are richer in magnesium, averaging 40
45% MgO as compared with 3640% in the barren flows (Figure 10).
The fine-grained, flowtop spinifex-textured peridotites in these units
tend to contain from 2832% MgO whereas elsewhere they have less
than 26%. This provides a very useful exploration guideline.
Presence of magmatic sulphide

The formation of a magmatic sulphide deposit requires that the parent magma be at least locally saturated with sulphide for a finite period
of time. Saturation leads to the segregation of droplets of immiscible sulphide liquid, which then must accumulate to some degree if economic
concentrations are to be formed. Since it is virtually impossible for the
accumulation process to operate with anything approaching 100% efficiency, some significant proportion of immiscible sulphide will remain
dispersed and ultimately become trapped in the silicate host rocks. The
presence of magmatic sulphide grains in an igneous rock is thus an indication of a potentially fertile magma.
Magmatic sulphide grains can sometimes be recognized in mafic
and ultramafic rocks that are not too badly altered. Such grains are commonly minute and may not be readily distinguished from secondary sulphides without microscopic examination. They are characterized by a
polymineralic composition (commonly pyrrhotite-chalcopyrite-pentlandite) and their textural relationship to primary silicate minerals
(globular or cuspate appearance where they are moulded around silicates). Duke and Naldrett (1976) give some of these criteria in their
description of magmatic and secondary sulphides in the Main Irruptive
at Sudbury.
Cameron et al. (1971) applied a lithogeochemical approach to detect
the presence of small quantities of such residual magmatic sulphide in
ultramafic rocks. They determined the concentrations of S and of sulphide-bound Ni, Cu and Co, and found that all four elements were
enriched in ore-bearing as compared with barren rock suites. Copper
and sulphur were the most significant factors in the discriminant function which distinguished the two populations. A practical consideration
here is that Cu and particularly S tend to be mobile during alteration of
ultramafic rocks. This means that a relatively large number of samples

from each body should be analysed.
Sulphur isotopes and Se/S ratios

It is widely believed that a significant component of the sulphur in
most massive accumulations of magmatic sulphides is of crustal rather
than mantle derivation. The parent magma from which these accumulations segregated presumably became saturated with sulphide by
assimilation of crustal sulphur. This applies to komatiite-associated
nickel sulphides (i.e., Kambalda-type deposits), deposits in intrusions
of continental flood basalt affinity (e.g., Norilsk, Duluth Complex,
Insizwa), and the ores of the Thompson Nickel Belt, among others. It is
important to note, however, that the sulphur in many disseminated magmatic sulphide deposits (e.g., the strata-bound platinum reefs) is
largely of mantle origin.
These observations suggest another lithogeochemical approach to
the exploration for massive Ni-Cu sulphide ores. It was noted above that
the presence of minute quantities of magmatic sulphides in an igneous
rock is indicative of a fertile intrusion or lava sequence. Taking this
one step further, geochemical parameters may be used to determine the
likely source of the sulphur in these magmatic sulphide grains. A strong
supracrustal signature would indicate that the parent magma had assimilated sulphur, which in turn suggests that the body in question would
have some potential to host a massive sulphide accumulation.
Two parameters that are indicative of the source of sulphur are the
sulphur isotopic composition and the Se/S ratio. The quantity d34 is
close to zero in sulphur of mantle origin but often very different from
zero in supracrustal sulphur (at least in post-Archean rocks). Similarly,
rocks of mantle derivation typically have lower Se/S ratios in the range
of 250350 10-6 whereas the ratio in supracrustal rocks is typically less
than 100 10-6 (e.g., Eckstrand et al., 1990).
Chalcophile element depletion

Chalcophile elements (Cu, Ni, Co, PGEs, etc.) partition strongly into
molten sulphide in preference to silicate liquid, and magmas from which
sulphide has segregated will be depleted in these elements. Chalcophile
element depletion, as revealed by lithogeochemistry, is therefore a
potentially useful indicator of igneous bodies that have crystallized from
sulphide-saturated magmas (Naldrett et al., 1984).
The magnitude of this depletion will depend upon a number of factors including the partition coefficient of the element, the relative masses
of sulphide and silicate melts, and the mechanism by which the two liquids equilibrate. Komatiitic sequences provide an ideal situation in
which to apply the chalcophile element depletion approach to exploration because they usually include spinifex-textured peridotites which
have compositions equivalent to magmatic liquids. Duke and Naldrett
(1978) quantitatively modelled the depletion patterns of Ni, Cu, and Co
in komatiitic magmas, and predicted that these could be used as an
exploration guide for Kambalda-type deposits. Subsequent studies have
shown that the spinifex-textured peridotites at Kambalda (Lesher et al.,
1981) and Scotia (Stolz, 1981) are indeed depleted in Ni. In each case,
the entire komatiite sequence shows evidence of depletion (Figure 11)
which means that this lithogeochemical approach would be useful in
identifying fertile komatiite successions but not in detailed exploration
within these sequences. In applying this approach, it is important to
Franklin, J.M.
203
Figure 11: Ni-depletion in the ore-bearing komatiite succession at Kambalda, Western Australia. The solid line represents the model compositional trend
produced by fractional crystallization of olivine; the dashed lines show the effect of removal of olivine and sulphide in 200:1 and 50:1 ratios (Duke 1979).
The dots give the compositions of spinifex-textured peridotites (STP) from Lesher et al. (1981).
sample the fine-grained spinifex in the flow-top, that will most closely
approximate the initial liquid composition.
In dealing with plutonic rocks, it is only rarely possible to identify
rocks which have liquid-equivalent compositions. However, the chalcophile element depletion concept also applies to minerals which crystallized from sulphide-saturated magmas. Olivine is the most useful
mineral in this respect because it normally contains readily detectable
concentrations of Ni. Naldrett et al. (1984) have described a number of
examples of nickel depletion in olivine from mineralized intrusions
including the Insizwa Complex of South Africa, the Moxie and Katahdin
intrusions in Maine, and the Dumont Sill in Qubec. Paktunc (1989) has
documented Ni-depleted olivines in the St. Stephen intrusion in
New Brunswick which hosts a number of zones of magmatic Ni-Cu
mineralization.
Chromite compositions
Lesher and Groves (1984) reported that chromites from mineralized
komatiite sequences at Kambalda contain significantly higher levels of Zn
than those from unmineralized sequences, specifically, 0.6 to 2.2 atomic
% as compared to less than 0.6 atomic %. Chromites from ultramafic host
rocks to ore at Thompson, Manitoba were found to contain similar high
levels. The suggestion of Lesher and Groves (1984) that this enrichment
is due to concentration of Zn in the silicate liquid during sulphide segregation is inconsistent with the inferred silicate/sulphide mass ratio (see
Duke [1990] for a discussion of the silicate/sulphide ratio which may
have prevailed at Kambalda). A more likely explanation may lie in the fact
that the magmas from which the sulphides segregated almost certainly
assimilated significant quantities of sulphidic sediments which were also
Zn-rich. Whatever the explanation, however, the elevated Zn content of
chromites from some mineralized sequences may be a useful indicator.
SUMMARY
Alteration associated with both lode-gold and volcanogenic massive
sulphide deposits results from interaction of high-temperature fluid
with wall rocks. The fluids responsible for both deposit types probably
had about the same range of temperatures (ca 300400C). Judging from
their respective products, lode-gold-related fluids had very low base
metal contents relative to VMS-forming fluids. Major districts containing either of these deposit types had fluids associated with them that
contained high CO2 contents; these CO2-rich fluids may not have been
the actual ore-forming fluid in either case, although these relationships
have not been clarified.
Precipitation mechanisms of the ore constituents (and certainly depositional environments) were very different. Gold deposits formed
through cooling on expansion of the fluid (e.g., in dilational structures;
Sibson et al., 1988) or through reduction of the sulphur content of the
fluid, by reaction with iron in the wall rocks to form pyrite. The latter
reaction effectively reduces the solubility of gold if it was being transported in a bisulphide complex. Deposition probably occurred about
4 km below the erosional surface of the time (Robert, 1996). Precipita-
204
tion of metals from a VMS-forming fluid occurred primarily through

cooling, either on contact with cold seawater at the sea floor or by heatconduction in the immediate footwall.
In the case of gold deposits, water, sulphur and CO2 are the primary
constituents added to the wall rocks. Potassium and Na were also added,
but the reservoir of these elements is presumed to be the hydrothermal
fluid responsible for mineralization; this fluid had limited amounts of
these alkali elements. In contrast, much of the alteration associated with
VMS deposits was formed from locally advecting (and progressively
heated) seawater. Retrograde solubility of Mg, and the virtually unlimited reservoir of Mg and K, provided the opportunity for much more
extensive addition of these elements to the footwall. Iron, sulphur and
silica are derived from the ore-forming fluid, however, and usually are
added only in the immediate footwall area.
One of the more important aspects of alteration associated with
these two deposit types is carbonatization at a regional scale. How can
carbonatization related to gold deposits be discriminated from that
related to VMS deposits ? Some guidelines are:
1. Carbonatization associated with gold deposits typically postdated the peak of metamorphism. Also, the carbonatized rocks
were not subjected to alkali-depletion, as was the case of the footwall sequences associated with VMS deposits. Consequently, the
carbonate alteration associated with gold deposits was not metamorphosed, or if it was, this metamorphism occurred in rocks
with normal alkali contents; metamorphosed alteration assemblages might contain diopside (or even secondary olivine, if temperatures were high enough). Metamorphosed carbonate
alteration assemblages associated with VMS deposits probably
contain chloritoid (Lockwood and Franklin, 1986) or staurolite,
due to the alkali-deficient nature of the rocks. Also, the latter rocks
are strongly per-aluminous, and typically contain andalusite (or
sillimanite at higher metamorphic grades).
2. Mass balance studies of each alteration type should indicate that
Ca, Mg, Fe and CO2 were added in VMS-related carbonate alteration, but only CO2 (and locally, possibly some K or Na) was added
during gold-related alteration.
3. The local alteration assemblages associated with gold mineralization (e.g., ankerite and paragonite) may be much more regionally developed under VMS deposits. Although little is known
about the source of CO2 associated with VMS deposits (it could
either be part of the hydrothermal fluid, a degassing product of an
underlying subvolcanic magma chamber, or formed from downward-advecting, progressively heated seawater), there is no indication of X CO2 gradients associated with its formation.
RECOMMENDATIONS
A few admonitions may be worth considering:
1. Geological models for ore deposition are based primarily on
empirical field observations, and refined using laboratory data.
The field observations typically include some recurring, somewhat
extraordinary assemblages of rocks, alteration patterns, or structures. Careful examination of geological information, or prefera-
bly, mapping, should be the most powerful exploration tool.

Where outcrop is sparse, geophysical or geochemical remote sensing methods, if applied with the full knowledge of the characteristics of ore deposits and their alteration assemblages, should
provide guidance.
2. Petrochemical trends can be useful indicators of ore potential for
magmatic and sea-floorhydrothermal deposits, but are of little
use for most types of vein deposits. High precision analytical data
are needed if reliable petrogenetic indicators are to be used. These
data should include determination of the volatile (CO2 and S) and
halogen elements and compounds, and REE. Indiscriminate determination of a large suite of volatile and trace elements could be
expensive. Where possible, sampling should be done with the best
geological knowledge at hand.
3. Alteration mineral assemblages provide excellent exploration
guides for VMS and lode gold deposits. Some of these can be determined in the field, others with a petrographic microscope, and
only a few require x-ray diffraction analyses. All of these techniques are inexpensive, readily available, and usually unambiguous. Mineral assemblages as exploration guides are under-used as
techniques in the exploration arsenal. Some useful staining methods are available for determining the composition of carbonate
minerals in the field. In the case of magmatic sulphides, on the
other hand, alteration often obscures primary trends making the
interpretation of lithogeochemistry more difficult.
4. Lithogeochemistry as an exploration technique has been used
widely, and, unfortunately, indiscriminately. The exploration geologist armed with some knowledge of alteration processes could use
subtle variations in the chemical composition of a rock to good
advantage. For example, Na is lost where the water/rock ratio was
high in an alteration zone (i.e., near a VMS deposit), but gained
where this ratio was low (i.e., in the high temperature reaction
zone, 12 km below the deposits). Both types of anomaly can be
useful guides to ore, but must be applied with full consideration of
stratigraphic implications. Analysis of the mineral assemblages in
such rocks will yield much more information than the chemical
data alone. Cook-book applications of lithogeochemical prospecting methods are potentially very misleading.
REFERENCES
Aggarwal, P.K., and Nesbitt, B.T., 1984, Geology and geochemistry of the Chu
Chua massive sulphide deposit, British Columbia: Economic Geology, 79,
815-825.
Ames, D.E., Franklin, J.M., and Froese, E., 1991, Zonation of hydrothermal alteration at the San Antonio Gold Mine, Bissett, Manitoba, Canada: Economic
Geology, Special issue on hydrothermal alteration as a guide to ore, 86, 3.
Andrews, A.J., Hugon, H., Durocher, M., Corfu, F., and Lavigne, M.J., 1986, The
anatomy of a gold-bearing greenstone belt, Red Lake, Northwestern Ontario,
Canada, in Macdonald, A.J., ed., Proceedings of Gold 86, an international
symposium on the geology of gold: Ontario Geological Survey, 3-22.
Anglin, C.D., and Franklin, J.M., 1986, Geochemistry and gold mineralization,
Geraldton, Ontario: in Chater, A. M., ed., Poster volume of Gold 86, an international symposium on the geology of gold: Ontario Geological Survey, 7-11.
Anglin, C.D.A., Franklin, J.M., and Osterberg, S.A., 1988, Use of U/Pb zircon
dating to establish some age and genetic constraints on base metal and gold
Franklin, J.M.
mineralization, Geraldton area, Ontario: in Van Breenan, O., ed., Radiogenic
age and isotopic studies: Report 2, Geological Survey of Canada Paper 88-2.
Baumgartner, L.P., and Olsen, S.N., 1995, A least-squares approach to mass
transport calculations using the isocon method: Economic Geology, 90,
1261-1270.
Beach, A., 1976, The interrelations of fluid transport, deformation, geochemistry
and heat flow in early Proterozoic shear zones in the Lewisian complex: Philosophical Transactions of the Royal Society, London, 280, 569-604.
Bell, K., Anglin, C.D.A., and Franklin, J.M., 1989, Nd-Sm and Rb-Sr isotope systematics of scheelites: Possible implications for the age and genesis of veinhosted gold deposits: Geology, 17, 500-504.
Bromley-Challenor, M.D., 1988, The Falun supracrustal belt, Part 1, Primary
geochemical characteristics of Proterozoic metavolcanics and granites, in
The Bregsladen Province, central Sweden: structure, stratigraphy and ore
forming processes: Geologie en Mijnbouw, 67, 2-4, 239-253.
Callan, N.J., and Spooner, E.T.C., 1989, Archean Au quartz vein mineralization
hosted in a tonalite-trondhjemite terrane, Renabie Mine area, Wawa, North
Ontario, Canada, in The geology of gold deposits: the perspective in 1988:
Economic geology Monograph 6.
Cameron, E.M., Siddeley, G., and Durham, C.C., 1971, Distribution of ore elements in rocks for evaluating ore potential: nickel, copper, cobalt and sulphur
in ultramafic rocks of the Canadian Shield: Canadian Institute of Mining and
Metallurgy, Special Volume 11, 298-313.
Campbell, I.H., Coad, P., Franklin, J.M., Gorton, M.P., Scott, S.D., Sowa, J., and
Thurston, P.C., 1982, Rare earth elements in volcanic rocks associated with
Cu-Zn massive sulphide mineralization: a preliminary report: Canadian
Journal of Earth Sciences, 19, 3, 619-623.
Card, K.D., Poulsen, K.H., and Robert, F., 1989, The Archean Superior Province
of the Canadian Shield and its lode gold deposits, in Keays, R.R., Ramsay,
W.R.H. and Groves, D.I., eds., The geology of gold deposits: the perspective
in 1988: Economic Geology Monograph 6, 19-36.
Cathles, L.M., 1990, Source zone processes in seafloor hydrothermal mineralization: Geological Society of America program with abstracts, A10.
Clark, M.E., Archibald, N.J., and Hodgson, C.J., 1986, The structural and metamorphic setting of the Victory gold mine, Kambalda, Western Australia, in
Macdonald, A.J., ed., Proceedings of Gold 86, an international symposium
on the geology of gold: Ontario Geological Survey, 243-254.
Clark, M.E., Carmichael, D.M., Hodgson, C.J., and Fu, M., 1989, Wall-rock alteration, Victory gold mine, Kambalda, Western Australia: Processes and P-TXCO2 conditions of metasomatism, in Keays, R.R., Ramsay, W.R.H. and
Groves, D.I., eds., The geology of gold deposits: The perspective in 1988: Economic Geology Monograph 6, 445-459.
Coad, P.R., 1985, Rhyolite geology at Kidd Creeka progress report: Cim Bulletin, 78, 70-83.
Colvine, A.C., Fyon, J.A., Heather, K.B., Marmont, S., Smith, P.M., and Troop,
D.G., 1988, Archean lode gold deposits in Ontario: Ontario Geological Survey, Misc. Paper 139.
Date, J., Watanabe, Y., and Saeki, Y., 1983, Zonal alteration around the Fukazawa
Kuroko deposits, Akita Prefecture, Northern Japan, in Ohmoto, H. and Skinner, B.J., eds., Kuroko and related volcanogenic massive sulphide deposits:
Economic Geology Monograph 5, 507-522.
Davidson, A.J., 1977, Petrography and chemistry of the Key Tuffite at Bell Allard,
Matagami, Qubec: M.Sc. thesis, McGill University.
Davies, J.F., Whitehead, R.E.S., Cameron, R.A., and Duff, D., 1982, Regional and
local patterns of CO2-K-Rb-As alteration: a guide to gold in the Timmins
area, in Hodder, R.W. and Petruk, W, eds., Geology of Canadian gold deposits: Canadian Institute of Mining and Metallurgy Special Volume 24, 130-143.
Dub, B., 1990, Metallognie Aurifere du Filon-Couche de Bourbeau, Region de
Chibougamau, Qubec: PhD thesis, Universit du Qubec.
Duke, J.M., 1979, Computer simulation of the fractionation of olivine and sulphide
from mafic and ultramafic magmas: Canadian Mineralogist, 17, 507-514.
Duke, J.M., 1990, Mineral deposit models: nickel sulphide deposits of the Kambalda type: Canadian Mineralogist, 28, 379-388.
205
Duke, J.M., and Naldrett, A.J., 1976, Sulphide mineralogy of the Main Irruptive,
Sudbury, Ontario: Canadian Mineralogist, 14, 450-461.
Duke, J.M., and Naldrett, A.J., 1978, A numerical model of the fractionation of
olivine and molten sulphide from komatiite magma: Earth and Planetary
Science Letters, 39, 255-266.
Eckstrand, O.R., Naldrett, A.J., and Lesher, C.M., 1990, Magmatic nickel-copper
sulphide deposits: Eighth IAGOD Symposium Program with Abstracts, A130.
Elliot, S.R., 1984, Geochemical, mineralogical and stable isotope studies at Owl
Creek Mine, Timmins, Ontario: BSc Thesis, Carleton University.
Embley, R.W., Jonasson, I.R., Perfit, M.R., Tivey, M., Malahoff, A., Franklin, J.M.,
Smith, M.F., and Francis, T.J.G., 1988, Submersible investigation of an extinct
hydrothermal system on the eastern Galapagos Ridge: Sulfide mounds, stockwork zone, and differentiated lavas: Canadian Mineralogist, 26, 517-540.
Franklin, J.M., 1995, Volcanic-associated massive sulphide deposits, in Kirkham,
R.V., Sinclair, W.D., Thorpe, R.I., and Duke, J.M., eds., Mineral deposit modelling: Geological Association of Canada Special Paper 40, 315-334.
Franklin, J.M., 1996, Volcanic-associated massive sulphide base metals, in
Ecstrand, O.R., Sinclair, W.D. and Thorpe, R.I., eds., Geology of Canadian
Mineral Types, Geological Survey of Canada 8, 158-183.
Franklin, J.M., Kasarda, J., and Poulsen, K.H., 1975, Petrology and chemistry of
the alteration zone of the Mattabi massive sulfide deposit: Economic Geology, 70, 63-79.
Franklin, J.M., Lydon, J.W., and Sangster, D.F., 1981, Volcanic-associated massive
sulfide deposits: Economic Geology 75th Anniversary Volume, 485-627.
Friesen, R.G., Pierce, G.A., and Weeks, R.M., 1982, Geology of the Geco base
metal deposit, in Hutchinson, R.W., Spence, C.D., and Franklin, J.M, eds.,
Precambrian sulphide deposits, Geological Association of Canada Special
Paper 25, 343-364.
Froese, E., 1969, Metamorphic rocks from the Coronation Mine and surrounding area, in Byers, A.R., ed., Symposium on the geology of the Coronation
Mine, Saskatchewan, Geological Survey of Canada Paper 68-5, 55-77.
Fryer, B.J., and Franklin, J.M., 1982, Hydrothermal alteration in Archean volcanic sequences: Geological Association of Canada, Annual General Meeting,
Program with Abstracts, Winnipeg.
Galley, A.G., 1993, Characteristics of semi-conformable alteration zones associated with volcanogenic massive sulphide districts: Journal of Geochemical
Exploration, 48, 175-200.
Galley, A.G., 1995, Target vectoring using lithogeochemistry: applications to the
exploration for volcanic-hosted massive sulphide deposits: Canadian Institute of Mining and Metallurgy Bulletin, 88, 990, 15-27.
Gass, I.G., and Smewing, J.D., 1973, Intrusion, extrusion and metamorphism at
constructive plate margins: Evidence from the Troodos massif, Cyprus:
Nature, 242, 26-29.
Gemmell, B.J., and Large, R.R., 1992, Stringer system and alteration zones underlying the Hellyer volcanic hosted massive sulphide deposit, Tasmania, Australia: Economic Geology, 87, 620-649.
Goodwin, A., Monster, J., and Thode, H.G., 1976, Carbon and sulphur isotope
abundances in Archean iron-formations and early Precambrian life: Economic Geology, 71, 870-891.
Grant, J.A., 1986, The isocon diagram-A simple solution to Gresens equation for
metasomatic alteration: Economic Geology, 81, 1976-1982.
Gresens, R.L., 1967, Composition-volume relationships of metasomatism: Chemical Geology, 2, 47-65.
Gresham, J.J., and Loftus-Hills, G.D., 1981, The geology of the Kambalda nickel
field, Western Australia: Economic Geology, 76, 1373-1416.
Guha, J., Gauthier, A., Vallee, M., Descatteaux, J., and Lange-Brard, F., 1982, Gold
mineralization patterns at the Doyen Mine (Silverstack), Bousquet, Qubec,
in Hodder, R.W. and Petruk, W., eds., Geology of Canadian gold deposits:
Canadian Institute of Mining and Metallurgy Special Volume 24, 50-57.
Gulson, B.L., and Mizon, K.J., 1979, Lead isotopes as a tool for gossan assessment
in base metal exploration: Journal of Geochemical Exploration, 11, 299-320.
Hannington, M.D., Herzig, P.M., and Scott, S.D., 1990, Auriferous hydrothermal
precipitates on the modern seafloor, in Foster, R.P, ed., Gold metallogeny and
exploration: Blackie and Son, 250-282.
206
Hannington, M.D., Jonasson, I.R., Herzig, P.M., and Petersen, S., 1995, Physical
and chemical processes of seafloor mineralization at mid-ocean ridges, in
Humphris, S.E., Zierenberg, R.A., Mullineaux, L.S., and Thomson, R.E., eds.,
Seafloor hydrothermal systems: physical, chemical, biological and interactions: Geophysical Monograph 91, 115-157.
Hannington, M.D., Thompson, G., Rona, P.A., and Scott, S.D., 1988, Gold and
native copper in supergene sylphides from the Mid Atlantic Ridge: Nature,
333, 6168, 64-66.
Hashiguchi, H., 1983, Practical application of low Na2O anomalies in footwall
acid lava for delimiting promising areas around the Kosaka and Fukazawa
kuroko deposits, Akita Prefecture, Japan, in Kuroko and related volcanic
massive sulphide deposits, Economic Geology Monograph 5, 387-394.
Herzig P.M., Hannington, M.D., Scott, S.D., Maliotis, G., Rona, P.A., and Thompson, G., 1991, Gold-rich seafloor gossans in the Troodos ophiolite and on the
Mid-Atlantic ridge, Economic Geology, 86, 1747-1755.
Hodgson, C.J., and Lydon, J.W., 1977, The geological setting of volcanogenic
massive sulfide deposits and active hydrothermal systems: some implications
for exploration: Canadian Mining and Metallurgy Bulletin, 70, 95-106.
Hodgson, C.J., and MacGeehan, P.J., 1982, A review of the geological characteristics of gold only deposits in the Superior Province of the Canadian Shield,
in Hodder, R.W. and Petruk, W., eds., Geology of Canadian gold deposits,
Hudak, G., 1996, The physical volcanology and hydrothermal alteration associated with late caldera volcanic and volcaniclastic rocks in volcanogenic massive sulphide deposits in the Sturgeon Lake region of Northwestern Ontario,
Canada: PhD thesis, University of Minnesota.
Iijima, A., 1974, Clay and zeolitic alteration zones surrounding Kuroko deposits
in the Hokuroko district, Northern Akita, as submarine hydrothermaldiagenetic alteration products: Society of Mining Geologists of Japan Special
Issue 6, 267-290.
Ishikawa, Y., Sawaguchi, T., Iwaya, S., and Horiochi, M., 1976, Delineation of
prospecting targets for Kuroko deposits based on models of volcanism of
underlying dacite and alteration halos: Mining Geology, 26, 105-117.
Kalogeropoulos, S.I., and Scott, S.D., 1983, Mineralogy and geochemistry of tuffaceous exhalites (tetsusekeie) of the Fuzakawa Mine, Hokuroku District,
Japan: Economic Geology Monograph 5, 412-432.
Kalogeropoulos, S.I., and Scott, S.D., 1989, Mineralogy and geochemistry of an
Archean tuffaceous exhalite: the Main Contact Tuff, Millenbach Mine area,
Noranda, Qubec: Canadian Journal of Earth Sciences, 26, 88-105.
Kappel, E.S., and Franklin, J.M., 1989, Relationships between geologic development of ridge crests and sulphide deposits in the northeast Pacific Ocean:
Economic Geology and the Bulletin of the Society of Economic Geologists,
84, 3, 485-505.
Keays, R.R., Ramsay, W.R.H., and Groves, D.I., 1989, The geology of gold deposits: the perspective in 1988: Economic Geology Monograph 6, 9-18.
Kerrich, R., 1983, Geochemistry of gold deposits in the Abitibi greenstone belt:
Canadian Institute of Mining and Metallurgy, Special Paper 27, 75p.
Kerrich, R., Fyfe, W.S., and Allison, I., 1977, Iron reduction around gold-quartz
vein, Yellowknife district, N.W.T., Canada: Economic Geology, 72, 657-663.
Kuhns, R.J., 1986, Alteration styles and trace element dispersion associated with
the Golden Giant deposit, Hemlo, Ontario, Canada, in Macdonald, A.J., ed.,
Proceedings of Gold 86, an international symposium on the geology of gold:
Ontario Geological Survey, 340-354.
Large, R.R., 1992, Australian volcanic-hosted massive sulphide deposits: features, styles and genetic models: Economic Geology, 87, 471-510.
Lavery, N.G., 1985, Quantifying chemical changes in hydrothermally altered volcanic sequencessilica enrichment as a guide to the Crandon massive sulfide
deposit, Wisconsin, U.S.A.: Journal of Geochemical Exploration, 24, 1-27.
Lesher, C.M., Lee, R.F., Groves, D.I., Bickle, M.J., and Donaldson, M.J., 1981,
Geochemistry of komatiites from Kambalda, Western Australia. I. Chalcophile element depletiona consequence of sulphide liquid separation from
komatiitic magmas: Economic Geology, 76, 1714-1728.
Lesher, C.M., and Stone, W.E., 1996. Exploration geochemistry of komatiites, in
Wyman, D.A., ed., Igneous trace element geochemistry applications for massive sulphide exploration: Geological Association of Canada, Short Course
Notes, v. 12, 153-204.
Lesher, C.M., and Groves, D.I., 1984, Geochemical and mineralogical criteria for
the identification of mineralized komatiites in Archean greenstone belts of
Australia: Proceedings of the 27th Intl. Geological Congress, 9, 283-302.
Lockwood, M.B., and Franklin, J.M., 1986, Implications of chemical trends
within the chloritoid-altered volcanic rocks of the Wawa belt: Ontario Geological Survey Geoscience Grant Research Program, Annual Report.
MacGeehan, P.J., and Maclean W.H., 1980, Tholeiitic basalt-rhyolite magmatism
and massive sulphide deposits at Matagami, Qubec: Nature, 283, 153-157.
MacGeehan, P.J., and Hodgson C.J., 1982, Environments of gold mineralozation
in the Campbell Red Lake and Dickenson mines, Red Lake district, Ontario,
in Hodder R.W. and Petruk, W., eds., Geology of Canadian gold deposits:
Marmot, S. and Corfu, F., 1989, Timing of gold introduction in the late Archean
tectonic framework of the Canadian Shield: evidence from U-Pb zircon geochronology of the Abitibi subprovince, in Keays, R., Ramsay, W. and Groves,
D.I., eds., The geology of gold deposits: the perspective in 1988: Economic
Geology Monograph 6, 101-111.
Morton, J.L., and Franklin, J.M., 1987, Two-fold classification of Archean volcanic-associated massive sulfide deposits: Economic Geology, 82, 1057-1063.
Morton, R L., Franklin, J.M., Hudak, G. and Walker, J., 1990, Early development
of an Archean submarine caldera complex with emphasis on the Mattabi ash
flow tuff and its relationship to massive sulfide deposits at Sturgeon Lake,
Ontario: Economic Geology, 86, 5, 1002-1011.
Munha, J., Fyfe, W.S., and Kerrich, R., 1980, Adularia, the charactersitic mineral
of felsic spilites: Contributions to Mineralogy and Petrology, 75, 15-19.
Munha, J., Barriga, F.J.A.S., and Kerrich, R., 1986, High 18O ore-forming fluids
in volcanic-hosted base-metal massive sulphide deposits: geologic 18O/16O,
and D/H evidence from the Iberian Pyrite belt, Crandon, Wisconsin, and
Blue Hill Maine: Economic Geology, 81, 530-552.
Naldrett, A.J., Duke, J.M., Lightfoot, P.C., and Thompson, J.F.H., 1984, Quantitative modelling of the segregation of magmatic sulphides: an exploration
guide: Canadian Institute of Mining and Metallurgy Bulletin, 77, 46-57.
Norton, D., and Knight, J., 1977, Transport phenomena in hydrothermal systems:
Cooling plutons, American Journal of Science, 277, 937-981.
Paktunc, A.D., 1989, Petrology of the St. Stephen intrusion and the genesis of
related nickel-copper sulphide deposits: Economic Geology, 84, 817-840.
Peter, J.M., and Goodfellow, W.D., 1996, Mineralogy, bulk and rare earth element
geochemistry of massive sulphide-associated hydrothermal sediments of the
Brunswick Horizon, Bathurst Mining Camp, New Brunswick, Canadian
Journal of Earth Sciences, 33, 2, 252-283.
Peterson, M.D., and Lambert, I.B., 1979, Mineralogical and chemical zonation
around the Woodlawn Cu-Pb-Zn ore deposit, southeastern New South
Wales: Journal of the Geological Society of Australia, 26, 169-186.
Poulsen, K.H., 1996, Lode gold, in Eckstrand, O.R., Sinclair, W.D., Thorpe, R.I.,
eds., Geology of Canadian mineral deposit types, Geological Survey of Canada, Geology of Canada, 8, 323-328.
Poulsen, H., and Hannington, M., 1996, Volcanic-associated massive sulphide
gold, in Eckstrand, O.R., Sinclair, W.D., Thorpe, R.I., eds., Geology of Canadian mineral deposit types, Geological Survey of Canada, 8, 183-196.
Richards, H.G., Cann, J.R. and Jensenius, J., 1989, Mineralogical zonation and
metasomatism of the alteration pipes of Cyprus sulfide deposits: Economic
Geology, 84, 91-115.
Robert, F., 1996, Quartz-carbonate vein gold, in Eckstrand, O.R., Sinclair, W.D.,
Thorpe, R.I., eds., Geology of Canadian mineral deposit types, Geological
Survey of Canada, Geology of Canada, 8, 350-366.
Robert, F., and Brown, A.C., 1986, Archean gold-bearing quartz veins at the
Sigma Mine, Abitibi greenstone belt, Qubec, Canada: Economic Geology,
14, 37-52.
Robert, F., and Poulsen, K.H., this volume, Gold deposits and their geological
characteristics.
Rock, N.M.S., Groves, D.I., Perring, C.S., and Golding, S.D., 1989, Gold, lamprophyres and porphyries: what does their association mean? in Keays, R.R.,
Ramsay, W.R.H. and Groves, D.I., eds., The geology of gold deposits: the perspective in 1988: Economic Geology Monograph 6, 609-625.
Franklin, J.M.
Saeki, Y., and Date, J., 1980, Computer applications to the alteration data of the
footwall dacite lava at the Ezuri kuroko deposits, Akita Prefecture: Mining
Geology, 30, 4, 241-250.
Schmincke, H.U., Rautenschlein, M., Robinson, P.T., and Meheger, J.M., 1983,
Troodos extrusive sequence of Cyprus: a comparison with oceanic crust:
Geology, 11, 405-409.
Shirozo, H., 1974, Clay minerals in altered wall rocks of the Kuroko-type deposits: Society of Mining Geologists Japan, Special Issue 6, 303-311.
Sibson, R.H., Robert, F., and Poulsen, K.H., 1988, High angle reverse faults, fluid
pressure cycling, and mesothermal gold quartz deposits: Geology, 16,
551-555.
Skirrow R.G., and Franklin J.M., 1994, Silicification and metal leaching in subconcordant alteration zones beneath the Chisel Lake massive sulphide
deposit, Snow Lake, Manitoba: Economic Geology, 89 (1), 31-50.
Spitz, G., and Darling, R., 1978, Major and minor element lithogeochemical
anomalies surrounding the Louvem copper deposit, Val DOr, Qubec:
Canadian Journal of Earth Sciences, 15, 7, 1161-1169.
Spooner, E.T.C., 1977, Hydrodynamic model for the origin of the ophiolitic
cupriferous pyrite ore deposits of Cyprus, in Volcanic processes in ore genesis: London Geological Society of London Special Publication 7, 58-71.
Spooner, E.T.C., and Fyfe, W.S., 1973, Sub-sea floor metamorphism, heat and
mass transfer: Contributions to Mineralogy and Petrology, 42, 287-304.
Spooner, E.T.C., Bechinsdale, R.D., England, P.C., and Senior, A., 1977a, Hydration, 18O enrichment and oxidation during ocean floor hydrothermal meta-
207
morphism of ophiolitic metabasic rocks from E. Liguria, Italy: Geochem. et

Cosmochim. Acta, 41, 857-872.
Spooner, E.T.C., Chapman, H.J., and Smewing, J.D., 1977b, Strontium isotopic
contamination and oxidation during ocean floor hydrothermal metamorphism of the ophiolitic rocks of the Troodos Masiff, Cyprus: Geochem. et
Cosmochim. Acta, 41, 873-890.
Stanley, C.R., and Modeisky, H.E., 1993, Lithogeochemical exploration for metasomatic halos around mineral deposits using Pearce element ratio analysis,
Geological Association of Canada, Mineralogical Association of Canada and
Canadian Geophysical Union, Joint Annual Meeting, Program with
Abstracts, Waterloo, 70.
Stolz, G.W., 1981, A mineralogical and geochemical interpretation of the
Archean volcanic pile in the vicinity of the Scotia ore-body, Western Australia: Ph.D. thesis, University of Adelaide.
Walford, P.C., and Franklin, J.M., 1982, The Anderson Lake Mine, Snow Lake, in
R.W. Hutchinson, C.D. Spence and J.M. Franklin, eds., Precambrian sulphide
deposits, Geological Association of Canada Special Paper 25, 481-525.
Wyman, D., and Kerrich, R., 1989, Archean shoshonitic lamprophyres associated
with Superior Province gold deposits: distribution, tectonic setting, noble
metal abundances and significance for gold mineralization, in Keays, R.R.,
Ramsay, W.R.H. and Groves, D.I., eds., The geology of gold deposits: the perspective in 1988: Economic Geology Monograph 6, 661-667.
Zaleski, E., 1989, Metamorphism, structure and petrogenesis of the Linda volcanogenic massive sulphide deposit, Snow Lake, Manitoba, Canada: PhD thesis, U. Manitoba.
208

03 01 Gold Exploration

Uploaded by

Copyright:

Available Formats

03 01 Gold Exploration

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

03 01 Gold Exploration

Uploaded by

Copyright:

Available Formats

Explor97 Master Page

Lithogeochemical and Mineralogical Methods

1. Geological Survey of Canada, Ottawa, Ontario, Canada

examples of attributes that were originally documented during the quest

volcanogenic massive sulphide deposits have been used very effectively

well-developed ferro-gabbro and granophyre phases; d) are devoid

LITHOGEOCHEMICAL AND MINERALOGICAL METHODS

Summary of alteration indices to test for the presence of alteration.

K2O / K2O + Na2O)

replacement of feldspar by sericite

Saeki & Date, 1980

addition of Fe and Mg as chlorite

Saeki & Date, 1980

MgO + Fe2O3 / (MgO + Fe2O3 + 2CaO + 2Na2O)

loss of CaO andNa2O by destruction feldspar

Na2O + CaO / (Na2O + CaO + K2O)

MgO + K2O / (MgO + K2O + CaO + Na2O)

sodium depletion (Al2O3 conserved)

Spitz & Darling, 1978

loss of CaO and Na2O by destruction feldspar

Saeki & Date, 1980

addition of Mg and K as chlorite and sericite

loss of CaO and Na2O by destruction feldspar

Date et al., 1983

FeO + MgO + K2O / (MgO + K2O + CaO + Na2O)

as above with addition of FeO

Fe2O3 / (Fe2O3 + MgO)

SiO2 vs. Zr/TiO2 (silicification)

residual to feldspar fractionation line

Pearce Element Ratios

molar Fe/Zr, Mg/Zr, Mn/Zr, K/Zr,CO2/Zr

addition of Fe, Mg etc. relative to conserved Zr

Stanley and Madeisky, 1993

molar (Na + K + 2Ca - Al/Zr) (alkali depletion)

residual to feldspar fractionation line

molar (Si/Zr) - 7.5 Al/Zr + 6.25) (silicification)

residual to feldspar fractionation line

e.g., sphalerite staining and sodium depletion

e.g. corundum > .1%, feldspar ratio

Alkali depletion, other

Mass Balance plots

All major and trace elements, altered vs. unaltered

Addition, loss, metasomatism,

Alteration beneath Cu-Zn massive sulphide deposits

1. Alteration pipes occur immediately below the massive sulphide

Figure 3: Composite REE patterns for felsic rocks in Archean sequences.

LITHOGEOCHEMICAL AND MINERALOGICAL METHODS

Composite characteristics of a Noranda-type alteration

2. Lower, semi-conformable alteration zones (Franklin et al., 1981)

Beneath deposits formed in shallow water (Mattabi-type), the pipes

cies varies considerably; the well-known Mg addition under some

Figure 6: Regional distribution of carbonate alteration in the Sturgeon

Alteration beneath Zn-Pb-Cu deposits

LITHOGEOCHEMICAL AND MINERALOGICAL METHODS

Semi-conformable alteration beneath Zn-Pb-Cu deposits occurs on

Syndepositional indicators of ore potential

LITHOGEOCHEMICAL AND MINERALOGICAL METHODS

vasive alteration is present in schistose deformation zones, but

Schematic illustration of alteration associated with lode-gold deposits.