F e A T U R e S
F e A T U R e S
F e A T U R e S
CX12T
he CX12T amplifier is ideal for use in any permanently installed sound system. Designed to meet the
specialized needs of high power, high quality audio
systems, the CX12T offers the features requested
most by contractors and installers from around the
world. The CX12T resides in a rugged three rackspace steel chassis approximately 17.9 inches deep.
With high quality internal isolation transformers, the
CX12T features built-in capability for driving 25, 70
or 100 volt distributed sound systems as well as direct output voice coil loads. Versatile design allows
LOAD
1kHz, 1% THD
400 watts
600 watts
475 watts
700 watts
900 watts*
Stereo (W/Ch)
8
4
2
25 volts
70 volts
100 volts
400 watts
500 watts
500 watts
Mono-Bridged
16
8
4
50 volts
140 volts
200 volts
800 watts
1200 watts
950 watts
1400 watts
1800 watts*
800 watts
1000 watts
1000 watts
*typical
CX12T Specifications
POWER OUTPUT
Direct output, watts per channel, both channels driven
8, 45 Hz-20 kHz, 0.1% THD
8, 1 kHz, 1% THD
4, 45 Hz-20 kHz, 0.1% THD
4, 1 kHz, 1% THD
2, 1 kHz, 1% THD*
Isolated outputs, watts per channel, both channels driven
70V or 100V, 1 kHz, 0.1% THD
25V, 1 kHz, 0.1% THD
Direct Outputs, bridged mono
8, 45 Hz-20 kHz, 0.1% THD
4, 1 kHz, 1% THD*
Isolated outputs, bridged mono
50V, 1 kHz, 0.1% THD
140V, 1 kHz, 0.1% THD
200V, 1 kHz, 0.1% THD
DISTORTION
400
475
600
700
900
500
400
1200
1800
800
1000
1000
FPO/BACK
FREQUENCY RESPONSE
Direct outputs:
-3 dB @ 45 Hz*, -0.2 dB @ 20 kHz
Isolated outputs:
45 Hz*-16 kHz, +0, -3 dB
* Low frequency response on T versions is limited by 18 dB/octave 45-Hz high-pass filter.
DAMPING FACTOR
OUTPUT REGULATION
NOISE
VOLTAGE GAIN
@ direct outputs
CONTROLS
Front: AC Switch
Rear: Parallel/Stereo/Bridge Switch,
Ch.1 and Ch. 2 Attenuator Knobs (11 detents: 0, -2, -4, -6, -8, -10, -12, -14, -18, -24, off)
FRONT PANEL/INDICATORS (per channel)
PROTECT:
Red LED
CLIP:
Red LED
SIGNAL:
Yellow LED
POWER:
Green LED
REAR PANEL/CONNECTORS (each channel)
Input:
Euro-style detachable header
Output:
Covered barrier strips
COOLING
AMPLIFIER PROTECTION
Output Averaging short circuit protection, open circuit, ultrasonic, RF, thermal muting
Stable into reactive or mismatched loads
LOAD PROTECTION
Turn-on/turn-off muting, DC-fault load grounding relay with internal fault fuses
POWER REQUIREMENTS:
POWER CONSUMPTION
Normal operation: 1/8 power @ 4 per channel
Worst case continuous program: 1/3 power @ 2 per channel
Maximum: full power @ 2 per channel
Multiply current by 0.5 for 220-240 VAC operation
Channel Load AC Current, Full Power AC Current, 1/3 Power AC Current, 1/8 Power AC Current, Idle
8 + 8
14.7 A
8.4 A
4.5 A
0.8 A
4 + 4
23 A
12.4 A
6.1 A
0.8 A
2 + 2
33 A
16.5 A
8.0 A
0.8 A
25V, 70V, 100V
21 A
10.9 A
5.7 A
0.8 A
DIMENSIONS
Faceplate Width
Chassis Depth
Faceplate Height
WEIGHT
1675 MacArthur Boulevard Costa Mesa, California 92626-1468 USA Phone: 714/754-6175 Fax: 714/754-6174