Scribd
Upload
1K views10 pages

Tms374 Ecu Decoder Manual

This document provides instructions for using a frequency sweeper tool to decode ECUs from various vehicle manufacturers, including Renault, Peugeot, Citroen, Daewoo, Hyundai, and Kia. The tool generates a 5V square wave output sweeping from 10kHz to 50Hz to decode the ECU. It requires connecting the ground wire to the ECU, connecting the data wire to the EPROM reset pin, powering on the ECU and tool, and waiting for the sweeping process to complete, at which point the ECU will be decoded. Diagrams show the pin locations for the reset pins and immobilizer data lines on different ECU types.

Uploaded by

Aldo Fabian Cencic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views10 pages

Tms374 Ecu Decoder Manual

This document provides instructions for using a frequency sweeper tool to decode ECUs from various vehicle manufacturers, including Renault, Peugeot, Citroen, Daewoo, Hyundai, and Kia. The tool generates a 5V square wave output sweeping from 10kHz to 50Hz to decode the ECU. It requires connecting the ground wire to the ECU, connecting the data wire to the EPROM reset pin, powering on the ECU and tool, and waiting for the sweeping process to complete, at which point the ECU will be decoded. Diagrams show the pin locations for the reset pins and immobilizer data lines on different ECU types.

Uploaded by

Aldo Fabian Cencic
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

TMS374 ECU DECODER

Introduction

Connection diagram:
+ :12v DC
- : GND
S :signal wire

This Tool is a frequency sweeper with 5V square wave output (Duty cycle 50%,
effective frequency range from over 10kHz (max 50kHz) to 50Hz) .This tool can be
also considered as a MCU version of the software TMS-374 Decoder ECU. The only
difference between the two tools is that the MCU version works without a PC.
A small MCU is used to generate the pulses instead of the PC RS232 Tx line.

Manual
After powering the device on - the LED should blink twice. The sweeping process starts as
power is supplied to the device. LED ON - means there are pulses on the output. After
reaching the lowest frequency the LED goes off and the mcu stops the generation.

Connect the GND line to any suitable GND on the ECU via the small grabber
Connect the Data line to the Reset pin on the EPROM via the small grabber
Power the ECU and then the sweeper, the sweeper will flash twice on power up
Press the button and the device will start sweeping, once the LED turns off your done
Cut the immo data line on the ECU before re-fitting back to car.

TMS-374 Decoder ECU info


The sweeper should work with the following ECUs:
-----------------------------Renault SIEMENS Fenix 3 and 5
-----------------------------Renault Megane 1400cc 8v
Renault Megane 1600cc 8v
Renault Megane 2000cc 8v
Renault Megane 2000cc 16V
Renault Megane Scenic 1400cc 8v
Renault Megane Scenic 1600cc 8v
Renault Megane Scenic 2000cc 8v
Renault Sefrane 2000cc 16V
Renault Laguna 2000cc 8v
Renault Laguna 2000cc 16v
Renault Espace 2000cc 8v
-----------------------------Renault SAGEM SAFIR 1 and 2
-----------------------------Renault Clio 1200cc 8V
Renault Clio 1400cc 8V
Renault Clio 1600cc 8V
Renault Clio 2000cc 16V Williams
Renault Laguna 1800cc 8V
Renault Laguna 2000cc 8V
Renault Laguna 1800cc 16V
Renault Laguna 2000cc 16V
Renault Twingo 1200cc 8V

NOTE: If reset pin is connected to ground then it


must be lifted or the track cut before decoding.
This can be re-attached after decoding the ecu.
As a rule of thumb keep the power connected
to the ECU for a futher five minutes after the decoder
has completed the decoding process

Sagem SL96 Psa


----------------------------NOTE: If reset pin is connected to ground then it
Peugeot 306 1400cc 8V
must be lifted or the track cut before decoding.
Peugeot 306 1600cc 16V
This can be re-attached after decoding the ecu.
Peugeot 306 1800 16V
Peugeot Ranch 1400 8V
As a rule of thumb keep the power connected
Citroen Berlingo 1400cc 8V
to the ECU for a futher five minutes after the decoder
Citroen Xrara 1400cc 8V
has completed the decoding process
Citroen Xrara 1800cc 16V
-----------------------------DAEWOO SIEMENS
-----------------------------Daewoo Matiz 800cc
-----------------------------HYUNDAI SIEMENS
-----------------------------Hyundai Coupe 1600cc 16V
Hyundai Coupe 2000cc 16V
-----------------------------KIA SIEMENS
-----------------------------Kia Rio 1300 16V
Kia Rio 1500 16V
-----------------------------MAGNETI MARELLI
-----------------------------1AP20, 1AP40, 1AP41, 1AP43, 1AP80, 1AP81, 1AP83 1AP90,
Citroen Berlingo 1800cc 8V
Citroen Saxo 1400cc 8V
Citroen Saxo 1600cc 16V
Citroen Xara 1400cc 8V
Citroen Xara 1800cc 8V
Citroen Xara 2000cc 16V
Citroen ZX 1400cc 8V
Peugeot 106 1400cc 8V
Peugeot 106 1600cc 8V
Peugeot 106 1600cc 16V
Peugeot 206 1100cc 8V
Peugeot 206 1400cc 8V
Peugeot 306 1400cc 8V
Peugeot 306 1600cc 8V
Peugeot 306 1800cc 8V
Peugeot 405 1800cc 8V
Peugeot 406 1800cc 8V
Peugeot Partner 1800 8V

TMS-374
1AP\SAGEM\SIEMENS

Procedure
Simply power the ECU and device using a suitable 12V power supply.
Connect the GND cable to a good ground source on the ECU and then the data line to
the Reset Pin on the flash 27c512 or 28F512 as shown in the diagram.
Start the device and wait for it to finish its cycle (the led will turn off). At this point
the ECU has been decoded and put into a new state. The Immo line will need to be
disconnected before the ECU is re-fitted back to the car.

SAGEM SAFIR 1
Microprocessore

Eprom
4

1 32 31 30

29

28

27

8
9
10
11

EP

M
O
R

26
25
24
23

12

22

13

21
14 15 16 17 18 19 20

ECU's with 27C512 PLCC RESET pin is 23


ECU's with 28F512 PLCC RESET pin is 22

CENTRALINE SAGEM SAFIR RENAULT 35 PIN


PIN 18 --- 12v+
PIN 4\34 --- GND
PIN 30 Immo data line (cut)

CENTRALINE SAGEM SAFIR 1 RENAULT 55 PIN


PIN 1 --- 12v+
PIN 2\3\18 --- GND
PIN 37 Immo line (cut)

SAGEM SAFIR 2
Microprocessore

Eprom
4

1 32 31 30

29

28

27

8
9
10
11

EP

M
O
R

26
25
24
23

12

22

13

21
14 15 16 17 18 19 20

ECU's with 27C512 PLCC RESET pin is 23


ECU's with 28F512 PLCC RESET pin is 22

CENTRALINE SAGEM SAFIR 2 RENAULT 55 PIN


PIN 1 --- 12v+
PIN 2\3\18 --- GND
PIN 37 Immo data line (cut)

SIEMENS DAEWOO
Microprocessore

Eprom
4

1 32 31 30

29

28

27

8
9
10
11

EP

M
O
R

26
25
24
23

12

22

13

21
14 15 16 17 18 19 20

ECU's with 27C512 PLCC RESET pin is 23


ECU's with 28F512 PLCC RESET pin is 22

CENTRALINE SIEMENS DAEWOO (MATIZ) 55 PIN


PIN 32\24 --- 12V+
PIN 2\3 --- GND
PIN 11 Immo data line (cut)

SIEMENS RENAULT
Microprocessore

Eprom
4

1 32 31 30

29

28

27

8
9
10
11

EP

M
O
R

26
25
24
23

12

22

13

21
14 15 16 17 18 19 20

ECU's with 27C512 PLCC RESET pin is 23


ECU's with 28F512 PLCC RESET pin is 22

CENTRALINE SIEMENS RENAULT 55 PIN


PIN 32\24\1 --- 12V+
PIN 2\3 --- GND
PIN 37 Immo data line on 1600 cc (cut)
PIN 35 Immo data line on 1800cc\2000 cc (cut)

MAGNETI MARELLI 1AP


Microprocessore

Eprom
4

1 32 31 30

29

28

27

8
9

EP

10
11

M
O
R

26
25
24
23

12

22

13

21
14 15 16 17 18 19 20

ECU's with 28F512 PLCC RESET pin is 22

CENTRALINE 1AP 55 PIN


PIN 35\13 --- 12v+
PIN 54\36 --- GND
PIN 27\48 Immo data line (cut)

SIEMENS HYUNDAI
Microprocessore

Eprom
4

1 32 31 30

29

28

27

8
9
10
11

EP

M
O
R

26
25
24
23

12

22

13

21
14 15 16 17 18 19 20

ECU's with 27C512 PLCC RESET pin is 23


ECU's with 28F512 PLCC RESET pin is 22

CENTRALINE SIEMENS HUNDAY 55 PIN

SAGEM SL96 PSA

ECU's with EPROM's 29F512 PLCC pin 22 is RESET

CENTRALINE SAGEM SL96 PSA


Pin 1 --- 12v+
Pin 2\3\18 --- GND
Pin 27\48 Immo data line (cut)

You might also like