The LM133/LM333 are adjustable 3-terminal negative voltage regulators capable of supplying over 3 amps of output current over an output voltage range of -1.2V to -32V. They require only 2 external resistors to set the output voltage and 1 output capacitor. Key features include excellent load and line regulation, low thermal transients, internal current limiting and thermal shutdown protection. They are easy to apply and well-suited for applications including local on-card regulation, programmable outputs, and precision current regulation.
The LM133/LM333 are adjustable 3-terminal negative voltage regulators capable of supplying over 3 amps of output current over an output voltage range of -1.2V to -32V. They require only 2 external resistors to set the output voltage and 1 output capacitor. Key features include excellent load and line regulation, low thermal transients, internal current limiting and thermal shutdown protection. They are easy to apply and well-suited for applications including local on-card regulation, programmable outputs, and precision current regulation.
The LM133/LM333 are adjustable 3-terminal negative voltage regulators capable of supplying over 3 amps of output current over an output voltage range of -1.2V to -32V. They require only 2 external resistors to set the output voltage and 1 output capacitor. Key features include excellent load and line regulation, low thermal transients, internal current limiting and thermal shutdown protection. They are easy to apply and well-suited for applications including local on-card regulation, programmable outputs, and precision current regulation.
The LM133/LM333 are adjustable 3-terminal negative voltage regulators capable of supplying over 3 amps of output current over an output voltage range of -1.2V to -32V. They require only 2 external resistors to set the output voltage and 1 output capacitor. Key features include excellent load and line regulation, low thermal transients, internal current limiting and thermal shutdown protection. They are easy to apply and well-suited for applications including local on-card regulation, programmable outputs, and precision current regulation.
The LM133/LM333 are adjustable 3-terminal negative voltage regulators capable of supplying in excess of b3.0A over an output voltage range of b1.2V to b32V. These regulators are exceptionally easy to apply, requiring only 2 external resistors to set the output voltage and 1 output capacitor for frequency compensation. The circuit design has been optimized for excellent regulation and low thermal transients. Further, the LM133 series features internal current limiting, thermal shutdown and safe-area compensation, making them substantially immune to failure from overloads. The LM133/LM333 serve a wide variety of applications including local on-card regulation, programmable-output voltage regulation or precision current regulation. The LM133/ LM333 are ideal complements to the LM150/LM350 adjustable positive regulators.
Connection Diagrams
Y Y Y Y Y Y Y Y Y Y
Output voltage adjustable from b1.2V to b32V
3.0A output current guaranteed, b55 C to a 150 C Line regulation typically 0.01%/V Load regulation typically 0.2% Excellent rejection of thermal transients 50 ppm/ C temperature coefficient Temperature-independent current limit Internal thermal overload protection P a Product Enhancement tested Standard 3-lead transistor package Output is short circuit protected
Typical Applications
TO-3 Metal Can Package
Adjustable Negative Voltage Regulator
TL/H/90651
Bottom View Steel TO-3 Metal Can Package (K STEEL) Order Number LM133K STEEL or LM333K STEEL See NS Package Number K02A
TL/H/9065 3
b VOUT e b 1.25V C1 e
TO-220 Plastic Package
1a
R2 120X
J # a
b IADJ c R2
1 mF solid tantalum or 10 mF aluminum electrolytic required for stability.
*C2 e 1 mF solid tantalum is required only if regulator is more than 4 from power supply filter capacitor. Output capacitors in the range of 1 mF to 1000 mF of aluminum or tantalum electrolytic are commonly used to provide lower output impedance and improved transient response.
TL/H/90652
Front View 3-Lead TO-220 Plastic Package (T) Order Number LM333T See NS Package Number T03B
(Note 1) b 65 C to a 150 C Storage Temperature Lead Temperature (Soldering, 10 sec.) TO-3 Package 300 C TO-220 Package 260 C ESD Susceptibility TBD
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Power Dissipation Internally Limited Input-Output Voltage Differential 35V Operating Junction Temperature Range TMIN to TMAX b 55 C to a 150 C LM133 b 40 C to a 125 C LM333
Electrical Characteristics LM133 Specifications with standard typeface are for TJ e 25 C, and those with boldface type apply over the full operating temperature range. (Note 3) Parameter Reference Voltage
Conditions
Typical
IL e 10 mA 3V s lVIN b VOUTl s 35V 10 mA s IL s 3A, P s PMAX
Line Regulation
3V s lVIN b VOUTl s 35V
IOUT e 50 mA (Note 4)
Load Regulation
10 mA s IOUT s 3A, P s PMAX
(Notes 4, 5)
Min (Note 2)
Max (Note 2)
Units
b 1.250
b 1.238
b 1.262
b 1.250
b 1.225
b 1.275
0.01 0.02
0.02 0.05
% /V
0.2 0.4
0.5 1.0
0.002
0.01
% /W
Thermal Regulation
10 ms Pulse
Temperature Stability
TMIN s TJ s TMAX
0.4
Long Term Stability
TJ e 125 C, 1000 Hours
0.15
Adjust Pin Current
Adjust Pin Current Change
10 mA s IL s 3A 3.0V s lVIN b VOUTl s 35V
Minimum Load Current
lVIN b VOUTl s 35V
lVIN b VOUTl s 10V 3V s lVIN b VOUTl s 10V lVIN b VOUTl e 20V lVIN b VOUTl e 30V
Current Limit (Note 5)
Output Noise (% of VOUT)
10 Hz to 10 kHz
Ripple Rejection
Thermal Resistance Junction-to-Case
65 70
90 100
mA
mA
2.5
5.0
1.2
2.5
3.9
3.0
2.4
1.25
0.4
0.3
mA
0.003
% (rms)
VOUT e 10V, f e 120 Hz
CADJ e 0 mF CADJ e 10 mF
60 77
dB
TO-3 Package (K STEEL)
1.2
Thermal Shutdown Temperature
163
150
1.8
C/W
190
Electrical Characteristics LM333 Specifications with standard typeface are for TJ e 25 C, and those with boldface type apply over the full operating temperature range. (Note 3) Parameter Reference Voltage
Conditions
Typical
IL e 10 mA 3V s lVIN b VOUTl s 35V 10 mA s IL s 3A, P s PMAX
Min (Note 2)
Max (Note 2)
b 1.250
b 1.225
b 1.275
b 1.250
b 1.213
b 1.287
0.01 0.02
0.04 0.07
% /V
0.2 0.4
1.0 1.5
0.002
0.02
% /W
Line Regulation
3V s lVIN b VOUTl s 35V
IOUT e 50 mA (Note 4)
Load Regulation
10 mA s IL s 3A, P s PMAX (Notes 4 and 5)
Thermal Regulation
10 ms Pulse
Temperature Stability
TMIN s TJ s TMAX
0.5
Long Term Stability
TJ e 125 C, 1000 Hours
0.2
Adjust Pin Current
% %
65 70
95 100
mA
mA
Adjust Pin Current
Change
10 mA s IL s 3A 3.0V s lVIN b VOUTl s 35V
2.5
Minimum Load Current
lVIN b VOUTl s 35V
lVIN b VOUTl s 10V 3V s lVIN b VOUTl s 10V lVIN b VOUTl e 20V lVIN b VOUTl e 30V
2.5
10
1.5
5.0
Current Limit (Note 5)
Output Noise (% of VOUT)
10 Hz to 10 kHz
Ripple Rejection
Thermal Resistance Junction to Case
3.9
mA
3.0
2.4
1.0
0.4
0.20
0.003
% (rms)
VOUT e 10V, f e 120 Hz
CADJ e 0 mF CADJ e 10 mF
60 77
dB
TO-3 Package (K STEEL)
1.2
1.8
TO-220 Package (T)
Thermal Shutdown Temperature Thermal Resistance Junction to Ambient (No Heatsink)
Units
163 K Package
35
T Package
50
C/W C
C/W
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device outside of its stated operating conditions. Note 2: All limits are guaranteed at either room temperature (standard type face) or at temperature extremes (bold typeface) by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods. Note 3: Unless otherwise specified: l VIN b VOUT l e 5V, IOUT e 0.5A, PDISS s 30W. Note 4: Load and line regulation are measured at constant junction temperature, using low duty cycle pulse testing (output voltage changes due to heating effects are covered by the Thermal Regulation specification). For the TO-3 package, load regulation is measured on the output pin, (/8 below the base of the package. Note 5: The output current of the LM333 is guaranteed to be t 3A in the range 3V s l VIN b VOUT l s 10V. For the range 10V s l VIN b VOUT l s 15V, the guaranteed minimum output current is equal to: 30/ (VIN b VOUT). Refer to graphs for guaranteed output currents at other voltages.
Guaranteed Performance Characteristics
LM133 Guaranteed Output Current
LM333 Guaranteed Output Current
TL/H/90654
TL/H/9065 5
Typical Applications (Continued)
b 5.2V Regulator with Electronic Shutdown
TL/H/9065 6
Negative Regulator with Protection Diodes
*When CL is larger than 20 mF, D1 protects the LM133 in case the input supply is shorted. **When C2 is larger than 10 mF and b VOUT is larger than b 25V, D2 protects the LM133 in case the output is shorted. ***In case VOUT is shorted to a positive supply, D3 protects the LM133 from overvoltage, and protects the load from reversed voltage.
TL/H/9065 7
Typical Applications (Continued)
High-Performance 9-Ampere Adjustable Regulator
*Wire R1 and R4 to the regulator that
provides the highest VOUT with a 3A load.
**Full output current requires 5V s l VIN VOUT l s 10V. At higher input-output voltages, load current will be less (see guaranteed curves)
TL/H/9065 8
Current Regulator
High Stability 10V Regulator
VREF IOUT e R1 *0.4X s R1 s 120X TL/H/90659 TL/H/9065 10
Typical Applications (Continued)
High-Current Adjustable Regulator
*Control regulator must have the largest VREF
**Full output current requires 5V s l VIN VOUT l s 10V. At higher input-output voltages, load current will be less (see guaranteed curves)
TL/H/9065 11
Adjustable Lab Voltage Regulator
Adjustable Current Regulator
TL/H/9065 13
IOUT e
# J 1.5V R1
*0.5X s R1 s 24X
TL/H/9065 12
*The 10 mF capacitors are optional to improve ripple rejection.
g 15% adjustable
Typical Applications (Continued)
per watt, within the first 10 ms after a step of power is applied. The LM133s specification is 0.01%/W, max.
THERMAL REGULATION When power is dissipated in an IC, a temperature gradient occurs across the IC chip affecting the individual IC circuit components. With an IC regulator, this gradient can be especially severe since the power dissipation is large. Thermal regulation is the effect of these temperature gradients on output voltage (in percentage output change) per watt of power change in a specified time. Thermal regulation error is independent of electrical regulation or temperature coefficient, and occurs within 5 ms to 50 ms after a change in power dissipation. Thermal regulation depends on IC layout as well as electrical design. The thermal regulation of a voltage regulator is defined as the percentage change of VOUT,
In Figure 1, a typical LM133s output drifts only 2 mV (or
0.02% of VOUT e b10V) when a 20W pulse is applied for 10 ms. This performance is thus well inside the specification limit of 0.01%/W c 20W e 0.2% max. When the 20W pulse is ended, the thermal regulation again shows a 2 mV step as the LM133 chip cools off. Note that the load regulation error of about 1 mV (0.01%) is additional to the thermal regulation error. In Figure 2 , when the 20W pulse is applied for 100 ms, the output drifts only slightly beyond the drift in the first 10 ms, and the thermal error stays well within 0.1% (10 mV).
TL/H/9065 15
TL/H/9065 14
FIGURE 2
FIGURE 1
Physical Dimensions inches (millimeters)
Steel TO-3 Metal Can Package (K STEEL)
Order Number LM133K STEEL or LM333K STEEL NS Package Number K02A 7
This data sheet contains preliminary limits and design specifications. Supplemental information will be published at a later date. National Semiconductor reserves the right to make changes in the produicts contained in this document in order to improve design or performance and to supply the best possible products. National also assumes no responsiblity for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representations that the circuits are free from patent infringement. Applications for any integrates circuits contained in this document are for illustration purposes only and National makes no representation or warranty that such applications will be suitable for the use specified without further testing or modification.
LIFE SUPPORT POLICY
NATIONALS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018
2. A critical component is any component of a life
support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80
National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960
National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
