Electric cylinders DNCE, with spindle drive

Electric cylinders DNCE, with spindle drive

Key features
At a glance
General

Properties

The electric cylinder DNCE is a mech

anical linear axis with piston rod. The
drive component consists of an elec
trically driven spindle, which converts
the rotary motion of the motor into the

-H-

linear motion of the piston rod.

The mechanical interfaces are largely
compatible with the standard cylinder
DNC.

Range of applications

 Choice of spindle type:

With lead screw (LS)
With ball screw (BS)
 Electric cylinder with lead screw
spindle is self-retarding
 Compact dimensions
Optional:
 Protection class IP65
 High corrosion protection
 NSF-H1 lubricant for the food
industry

 Lead screw spindle

For applications with slow feed
speeds
 Ball screw spindle
For applications with high feed
speeds and high running
performance

Note

The electric cylinder is of limited

suitability for the food industry.

Further information www.festo.com/

sp User documentation.

Entire system consisting of electric cylinder, motor and motor mounting kit
Electric cylinder

-H-

1
2

1 Parallel kit
2 Axial kit
3 Slot for proximity sensor

Note

The lead screw spindle is self-retard

ing, which means that slow move
ments cannot be excluded in the
event of vibration.
The entire system with intelligent
motor unit MTR-DCI is self-locking.

4 Choice of spindle type:

With lead screw spindle (LS)
With ball screw spindle (BS)
18

Motor/motor unit
1 Motor unit MTR-DCI
2 Servo motor EMME-AS, EMMS-AS
3 Stepper motor EMMS-ST

1
Motor mounting kit
Axial kit

-H-

Note

A range of specially adapted

complete solutions is available for
the electric cylinder DNCE and the
motors/motor units.
18

Parallel kit
A range of complete kits is available
for both parallel and axial motor
mounting.

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Key features and type codes
26

Longer service life with bellows kit EADB

The protective bellows kit is a leakfree system. To prevent unwanted me

dia from being drawn in, the supply
and exhaust air must be ducted via a
pressure compensation hole in the
connection part 1.

The kit protects the piston rod, seal

and bearings against a wide variety of
media, for example:
 Dust
 Chippings
 Oil
 Grease
 Fuel

The electric cylinder to IP65 fulfils the

specifications to IEC 60 529.
Air is exchanged between the interior
of the cylinder and the environment
via a pressure compensation hole 1
in the cylinder barrel. This prevents
negative pressure or excess pressure
in the interior of the cylinder.

It also prevents unwanted media

being drawn in.

17

Use in dusty or wet environments thanks to protection to IP65 (feature P5)

1

Protection to IP65 can only be selec

ted in combination with DNCE--BS
(ball screw spindle).

Type codes
DNCE

32

100

BS

10P

Q-P5

Type
DNCE

Electric cylinder

Size
Stroke [mm]
Drive function
LS
BS

Lead screw spindle

Ball screw spindle

Spindle pitch [mm]

Variant
Q
K8
K3
P5
R3
FG

Non-rotating piston rod

Extended piston rod
Female piston rod thread
Protection class IP65
High corrosion protection
Lubrication approved for use in food
applications

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

Electric cylinders DNCE, with spindle drive

Peripherals overview

2
6

9
5
aA
8

aD
aJ

aC
aB

bF
bG

aF

4
cJ

aE
bH
aG

bA

bD

aH
bB

aI
9

bJ
bE

1
2
3
bI

bC

Mounting attachments and accessories

Brief description

Page/Internet

For mounting the cylinder

31

Cannot be used on the bearing cap in combination with bellows kit EADB

32

Cannot be used on the bearing cap in combination with bellows kit EADB

33

2
3

Foot mounting
HNC/CRHNC
Flange mounting
FNC/CRFNG
Trunnion flange
ZNCF/CRZNG

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Peripherals overview
Mounting attachments and accessories
Brief description

Page/Internet

For cylinders with trunnion mounting

34

With parallel motor mounting

35

With parallel motor mounting, with spherical bearing

38

With parallel motor mounting, weld-on, with spherical bearing

38

With parallel motor mounting, with spherical bearing

35

With parallel motor mounting, with spherical bearing

38

With parallel motor mounting

36

With parallel motor mounting, with spherical bearing

37

With parallel motor mounting

37

With parallel motor mounting

38

With parallel motor mounting, with spherical bearing

38

For mounting anywhere along the cylinder profile barrel. Cannot be mounted in the vicinity of the
motor with parallel motor mounting
With axial motor mounting
Cannot be used in combination with the axial kit EAMM-A--S1 (protection class IP65)
With spherical bearing

38

To compensate for radial deviations

39

Permits a swivelling movement of the cylinder in one plane

39

For compensating radial and angular deviations

39

For rod eye SGS

39

For swivel mounting of cylinders

39

For protecting electric cylinders against rotation at high torque loads

Cannot be used in combination with bellows kit EADB
For position sensing. Can be integrated in the sensor slot, thus avoiding projecting parts

39

For protecting against the ingress of dirt

40

For parallel motor mounting

18

For axial motor mounting

18

For mounting the electric cylinder via the profile

Cannot be mounted in the vicinity of the motor in combination with the parallel kit EAMM-U
Compensates the play between the piston rod of the electric cylinder DNCE and the yoke plate of the
guide unit FENG
Protects the cylinder (piston rod, seal and bearings) against a wide range of media and thus
prevents premature wear
The kit can only be used in combination with an extended piston rod (K8)

30

5
6
7
8
9
aJ
aA
aB
aC
aD
aE
aF
aG
aH
aI
bJ
bA
bB
bC
bD
bE
bF
bG
bH
bI
cJ

Trunnion support
LNZG/CRLNZG
Swivel flange
SNC
Clevis foot
LSNG
Clevis foot
LSNSG
Swivel flange
SNCS
Clevis foot
LBG
Swivel flange
SNCL
Swivel flange
SNCB/SNCB--R3
Swivel flange
SNCB/SNCB--R3
Clevis foot
LNG/CRLNG
Clevis foot
LSN
Trunnion mounting kit
DAMT
Foot mounting
HNCE
Rod eye
SGS/CRSGS
Coupling piece
KSZ
Rod clevis
SG/CRSG
Self-aligning rod coupler
FK/CRFK
Right-angle clevis foot
LQG
Rod clevis
SGA
Guide unit
FENG
Proximity sensor
SME/SMT-8
Slot cover
ABP-5-S
Parallel kit
EAMM-U
Axial kit
EAMM-A
Profile mounting
EAHF
Compensating element
EADC
Bellows kit
EADB

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

29
39

40

40
26

Electric cylinders DNCE, with spindle drive

Technical data

-N-

Function

-T-W-

Size
32 63
Stroke length
1 800 mm
www.festo.com

With axial kit

General technical data
Size

32

Design

Mounting position

Spindle pitch
Spindle diameter
Max. stat. axial force
Max. feed force Fx1)
Continuous feed force1)
Max. driving torque2)
Max. radial force3)
Max. speed
Max. rotational speed
Max. acceleration
Reversing backlash4)
Repetition accuracy

2)
3)
4)

63

M10x1.25
M6
1 400
Non-rotating piston rod
Plain-bearing guide
0
0.30

M12x1.25
M8
1 600

M16x1.5
M10
1 800

0.25

0.20

0.0001

E + 0.5

v2

0.0002

E + 0.5

v2

0.0004

E + 0.5

v2

100
Via proximity sensor
Via female thread
Via accessories
Any

In the case of the variant with lead screw spindle (LS), the duty cycle depends on the speed

Mechanical data
Size
Spindle design

1)

40

With lead screw spindle (LS)

With ball screw spindle (BS)

Piston rod thread

Male thread
Female thread
Working stroke
[mm]
Variant
Protection against rotation/guide
Stroke reserve
[mm]
Max. torsion angle
[]
of the piston rod
Impact energy (E)
[J]
in the end positions
Duty cycle1)
[%]
Position sensing
Type of mounting

1)

With parallel kit

[mm/
rev.]
[mm]
[N]
[N]
[N]
[Nm]
[N]
[m/s]
[rpm]
[m/s2]
[mm]
[mm]

32
LS-1,5P

BS-3P

BS-10P

40
LS-2,5P

BS-5P

BS-12,7P

63
LS-4P

BS-10P

BS-20P

1.5

10

2.5

12.7

10

20

9
600
300
300
0.4
120
0.06
2,400
1
0.2
0.07

10
600
300
240
0.4
120
0.15
3,000
6
0.05
0.02

10
600
350
280
0.8
120
0.5
3,000
6
0.05
0.02

12.5
1,400
600
600
1.15
260
0.07
1,650
1
0.2
0.07

12
1,400
525
420
0.9
260
0.25
3,000
6
0.05
0.02

12.7
1,400
800
640
1.9
260
0.64
3,000
6
0.05
0.02

20
3,700
1,000
1,000
3
300
0.07
1,050
1
0.2
0.07

20
3,700
2,500
2,000
4.9
300
0.5
3,000
6
0.05
0.02

20
3,700
1,625
1,300
5.9
300
1.0
3,000
6
0.05
0.02

In the case of the variant with lead screw spindle (LS), the feed force depends on the speed 10
The feed force in the case of the variant with ball screw spindle (BS) 8
In the case of the variant with lead screw spindle (LS), the driving torque depends on the rotational speed 11
At the drive shaft
In new condition

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Technical data
Mechanical data
Size
Spindle design
No-load driving torque
With axial kit1)
DNCE-
DNCE--P5
With parallel kit1)
DNCE-
DNCE--P5
Continuous driving torque
1)

32
LS-1,5P

BS-3P

BS-10P

40
LS-2,5P

BS-5P

BS-12,7P

63
LS-4P

BS-10P

BS-20P

[Nm]
[Nm]

0.08

0.08
0.12

0.08
0.12

0.12

0.12
0.18

0.12
0.18

0.3

0.2
0.3

0.2
0.3

[Nm]
[Nm]
[Nm]

0.13

0.4

0.13
0.17
0.3

0.13
0.17
0.6

0.22
0.17
1.15

0.22
0.28
0.8

0.22
0.28
1.6

0.6

0.5
0.6
4.1

0.5
0.6
4.8

Measured at a speed of 200 rpm

Operating and environmental conditions

Ambient temperature1)
[C]
Storage temperature
[C]
Protection class to IEC 60529
DNCE-
DNCE--P5
Relative air humidity
[%]
Suitability for use in the food industry2)
Corrosion resistance class CRC3)
DNCE--R3
1)
2)
3)

0 50
25 +60
IP40
IP65
0 95
As per manufacturer's declaration
3

Note operating range of proximity sensors and motors

Additional information www.festo.com/sp User documentation.
Corrosion resistance class CRC 3 to Festo standard FN 940070
High corrosion stress. Outdoor exposure under moderate corrosive conditions. External visible parts with primarily functional requirements for the surface and which are in direct contact with a normal industrial
environment.

Weight [g]
Size
Spindle design

32
LS-1,5P

BS-3P

BS-10P

40
LS-2,5P

BS-5P

BS-12,7P

63
LS-4P

BS-10P

BS-20P

Basic weight with 0 mm stroke

Additional weight per 10 mm stroke
Moving load with 0 mm stroke
Moving load per 10 mm stroke

720
32.4
150
6.9

750
33
170
6.9

770
33.6
200
6.9

1,210
46.1
250
8.9

1,270
45.5
310
8.9

1,350
46.7
380
8.9

2,790
79.8
600
12.8

3,010
81.2
810
12.8

3,010
81.2
810
12.8

Mass moment of inertia

Size
Spindle design

32
LS-1,5P

BS-3P

BS-10P

40
LS-2,5P

BS-5P

BS-12,7P

63
LS-4P

BS-10P

BS-20P

0.0433
0.0361
0.0006

0.0439
0.0476
0,0023

0.0446
0.0595
0.0253

0.1316
0.1341
0.0016

0.1304
0.1163
0.0063

0.1337
0.1572
0.0409

0.7565
0.8176
0.0041

0.7626
0.9090
0.0253

0.7624
0.9103
0.1013

J0 with 0 mm stroke
jH per metre stroke
jL per kg working load

[kg cm2]
[kg cm2/m]
[kg cm2/kg]

The mass moment of inertia JA of the

electric cylinder is calculated as
follows:

2014/08 Subject to change

JA = J0 + jH x working stroke [m] + jL x mworking load [kg]

Internet: www.festo.com/catalogue/...

Electric cylinders DNCE, with spindle drive

Technical data
Calculation of the mean feed force Fxm for the electric cylinder DNCE with ball screw spindle (BS)
The peak feed force value must not ex
ceed the maximum feed force within a
movement cycle. In the case of vertical
operation, the peak value is generally

achieved during the acceleration

phase of the upwards stroke. If the
maximum feed force is exceeded, this
can increase wear and thus shorten

the service life of the ball screw

spindle. The maximum speed must
likewise not be exceeded.

F x v F xmax.
and
vx v vxmax.

Mean feed force (to DIN 69 051-4)

During operation, the continuous feed
force may be briefly exceeded up to
the maximum feed force. The

F xm +3

x1

q
 +
100

vx
vxm
vx1
v xm

Fx1

q1
3
) F x2
100

vx2
vxm

q2
3
) F x3
100

v x3
vxm

Fxmax
Fx3

q3
) AAA
100

Fx [N]

F xm +3

F xm v F xcont

continuous feed force must, however,

be adhered to when averaged over a
movement cycle.

Fxm

Fx2

q1

q2
q [100%]

q3

Mean feed speed (to DIN 69 051-4)

Fx
Fxm
Fxmax.
Fxcont
q

vx

q
+ vx1
100

q2
) vx3
100

q1
) vx2
100

Feed force
Mean feed force
Max. feed force
Continuous feed force
Time

vx
vxm
vxmax.

q3
) AAA
100

vx 2
vx [mm/s]

vxm +

Feed speed
Mean feed speed
Max. feed speed

vxmax
vx 3

vxm

vx 1

q1

q2
q [100%]

q3

Materials
Sectional view
1

Electric cylinder
1
2
3
4
5
6

Bearing cap
Cylinder barrel
Piston rod
Spindle
Spindle nut for LS
Spindle nut for BS
Drive cover

Painted die-cast aluminium

Smooth anodised wrought aluminium alloy
High-alloy stainless steel
Steel
Polyacetal
Steel
Painted die-cast aluminium

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Technical data
Maximum permissible loads on the piston rod
Definition of the stroke length l:
l = Stroke + value of the piston rod
extension K8

If there are two or more forces and

torques simultaneously acting on
the piston rod, the following
equations must be satisfied:
|Fy|
|My|
|Fz|
|Mz|
)
)
)
v1
Fymax. Fzmax. Mymax. Mz max.
|Fx| v Fxmax
|Mx| v Mxmax
Maximum permissible lateral forces Fymax and Fzmax on the piston rod as a function of stroke length l
Horizontal mounting position
Vertical mounting position

DNCE-32-LS/BS
DNCE-40-LS/BS
DNCE-63-LS/BS

-H-

Size
Note

PositioningDrives
sizing software
www.festo.com

2014/08 Subject to change

32

Maximum permissible forces and torques

Fxmax (static)
[N]
600
Mxmax
[Nm]
1
Mymax, Mzmax
[Nm]
8

40

63

1,400
1
20

3,700
1.5
27

Internet: www.festo.com/catalogue/...

Electric cylinders DNCE, with spindle drive

Technical data
Feed force F as a function of speed v
DNCE-32-1299-LS-

DNCE-32-300400-LS-

DNCE-40-1299-LS-

DNCE-40-300600-LS-

DNCE-63-1419-LS-

DNCE-63-420800-LS-

Recommended operating range

Permissible operating range
(duty cycle 50% recommended)

10

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Technical data
Driving torque M as a function of rotational speed n
DNCE-32-1299-LS-

DNCE-32-300400-LS-

DNCE-40-1299-LS-

DNCE-40-300600-LS-

DNCE-63-1419-LS-

DNCE-63-420800-LS-

Recommended operating range

Permissible operating range
(duty cycle 50% recommended)

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

11

Electric cylinders DNCE, with spindle drive

Technical data
Rotational speed n as a function of speed v
DNCE--LS-

DNCE-32-LS-1,5P
DNCE-40-LS-2,5P
DNCE-63-LS-4P

DNCE--BS-

DNCE-32-BS-3P
DNCE-40-BS-5P
DNCE-63-BS-10P

DNCE-32-BS-10P
DNCE-40-BS-12,7P
DNCE-63-BS-20P

Driving torque M as a function of feed force F

-H-

Note

The frictional torques at room

temperature are taken into
consideration in the graphs.

The frictional torques with the

DNCE--LS (lead screw spindle)
increase at lower temperatures.

PositioningDrives
sizing software
www.festo.com

DNCE--LS-

DNCE-32-LS-1,5P
DNCE-40-LS-2,5P
DNCE-63-LS-4P
DNCE--BS-

DNCE-32-BS-3P
DNCE-40-BS-5P
DNCE-63-BS-10P

12

DNCE-32-BS-10P
DNCE-40-BS-12,7P
DNCE-63-BS-20P

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Technical data
Piston rod displacement f as a function of stroke length l
Definition of the stroke length l:
l = Stroke + value of the piston rod
extension K8

DNCE-32-

DNCE-40-

Lateral force F = 0 N
Lateral force F = 10 N
Lateral force F = 20 N
Lateral force F = 45 N

Lateral force F = 0 N
Lateral force F = 20 N
Lateral force F = 30 N
Lateral force F = 40 N
Lateral force F = 115 N

DNCE-63-

Lateral force = 0 N
Lateral force = 20 N
Lateral force = 30 N
Lateral force = 40 N
Lateral force = 95 N

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

13

Electric cylinders DNCE, with spindle drive

Technical data
Mean feed force F as a function of running performance L (to DIN 69 051-4)
DNCE-32--BS-

DNCE-32-BS-3P
DNCE-32-BS-10P

DNCE-40--BS-

DNCE-40-BS-5P
DNCE-40-BS-12,7P

DNCE-63--BS-

DNCE-63-BS-10P
DNCE-63-BS-20P

-H-

Note

 The specifications for running

performance are based on
experimentally determined and
theoretically calculated data. The

14

running performance attainable in

practice can deviate considerably
from the specified curves under
different parameters.

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Technical data
Download CAD data www.festo.com

Dimensions
Basic version

= plus stroke length

Size

AM

d11

B1

B2

BG

D1

h9

D2

h6

D3

f7

D4

G1

H1

H2

KK

32
40
63

22
24
32

30
35
45

19
20
31

32
42
62

16
16
17

16
20
28

6
8
12

32
40
60

M3
M4
M5

45.5
54
75.5

24
28.5
34

26
30
36

19
20
31

32
42
62

M10x1.25
M12x1.25
M16x1.5

Size

L1

L2

L3

L4

L5

MM

MP

RT

TG

VA

18
21.5
28.5

122
146.5
177

15.9
18.4
23.5

8
14
17

3.5
3.5
4.5

12
16
20

M3
M3
M4

M6
M6
M8

32.5
38
56.5

7
7
9

[mm]

[mm]
32
40
63

VD

WH

ZJ

26
30
37

148
176.5
214

10
13
17

17
19
24

6
6
8

+1/0.7

Variants
K8 Extended piston rod

10
10.5
15

K3 Female piston rod thread

P5 Protection class IP65

Size
[mm]

A2
max.

AF

EE

KF

L6

T5

D5

WH

32
40
63

200
200
200

12
12
16

Gx
G
G

M6
M8
M10

37.6
45.6
57.6

2.6
3.3
4.7

6.4
8.4
10.5

26
30
37

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

15

Electric cylinders DNCE, with spindle drive

Technical data
Ordering data DNCE-32
Stroke
Part No.
[mm]

Type

Stroke
[mm]

Ball screw spindle with spindle pitch 3 mm

100
543 115 DNCE-32-100-BS-3P-Q
200
543 116 DNCE-32-200-BS-3P-Q
300
543 117 DNCE-32-300-BS-3P-Q
400
543 118 DNCE-32-400-BS-3P-Q

Part No.

Type

Lead screw spindle with spindle pitch 1.5 mm

100
543 111 DNCE-32-100-LS-1,5P-Q
200
543 112 DNCE-32-200-LS-1,5P-Q
300
543 113 DNCE-32-300-LS-1,5P-Q
400
543 114 DNCE-32-400-LS-1,5P-Q

Ball screw spindle with spindle pitch 10 mm

100
543 119 DNCE-32-100-BS-10P-Q
200
543 120 DNCE-32-200-BS-10P-Q
300
543 121 DNCE-32-300-BS-10P-Q
400
543 122 DNCE-32-400-BS-10P-Q
Ordering data DNCE-40
Stroke
Part No.
[mm]

Type

Stroke
[mm]

Ball screw spindle with spindle pitch 5 mm

100
543 127 DNCE-40-100-BS-5P-Q
200
543 128 DNCE-40-200-BS-5P-Q
300
555 466 DNCE-40-300-BS-5P-Q
400
543 129 DNCE-40-400-BS-5P-Q
600
543 130 DNCE-40-600-BS-5P-Q

Part No.

Type

Lead screw spindle with spindle pitch 2.5 mm

100
543 123 DNCE-40-100-LS-2,5P-Q
200
543 124 DNCE-40-200-LS-2,5P-Q
300
555 465 DNCE-40-300-LS-2,5P-Q
400
543 125 DNCE-40-400-LS-2,5P-Q
600
543 126 DNCE-40-600-LS-2,5P-Q

Ball screw spindle with spindle pitch 12.7 mm

100
543 131 DNCE-40-100-BS-12,7P-Q
200
543 132 DNCE-40-200-BS-12,7P-Q
300
555 467 DNCE-40-300-BS-12,7P-Q
400
543 133 DNCE-40-400-BS-12,7P-Q
600
543 134 DNCE-40-600-BS-12,7P-Q
Ordering data DNCE-63
Stroke
Part No.
[mm]

Type

Stroke
[mm]

Ball screw spindle with spindle pitch 10 mm

100
555 470 DNCE-63-100-BS-10P-Q
200
543 139 DNCE-63-200-BS-10P-Q
300
555 471 DNCE-63-300-BS-10P-Q
400
543 140 DNCE-63-400-BS-10P-Q
600
543 141 DNCE-63-600-BS-10P-Q
800
543 142 DNCE-63-800-BS-10P-Q

Part No.

Type

Lead screw spindle with spindle pitch 4 mm

100
555 468 DNCE-63-100-LS-4P-Q
200
543 135 DNCE-63-200-LS-4P-Q
300
555 469 DNCE-63-300-LS-4P-Q
400
543 136 DNCE-63-400-LS-4P-Q
600
543 137 DNCE-63-600-LS-4P-Q
800
543 138 DNCE-63-800-LS-4P-Q

Ball screw spindle with spindle pitch 20 mm

100
555 472 DNCE-63-100-BS-20P-Q
200
543 143 DNCE-63-200-BS-20P-Q
300
555 473 DNCE-63-300-BS-20P-Q
400
543 144 DNCE-63-400-BS-20P-Q
600
543 145 DNCE-63-600-BS-20P-Q
800
543 146 DNCE-63-800-BS-20P-Q

-H-

Note

Order variable strokes via the

modular product system 17

16

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Ordering data Modular products
Ordering table
Size

32

40

63

0
M Module No.

555488

555489

555490

Function
Size
Stroke

Electric cylinder
32
40
[mm] 100
200
300
400

600

1 400
1 600
Drive type
Lead screw spindle
Ball screw spindle
Spindle pitch
[mm] 1.5

2.5
3

5
10

12.7

Protection against rotation

Non-rotating piston rod
0
O Extended piston rod
1 200
Female thread
M6
M8
Protection class to IEC 60529
IP65
Corrosion protection
High corrosion protection
Lubrication
Lubrication approved for use in food applications
1

1.5P, 2.5P, 4P

3P, 5P, 10P, 12.7P, 20P, K8, K3, P5

R3

Only with P5

FG

Only with R3 and P5

Condi
tions

63

800
1 800

Code

Enter
code

DNCE
-
-

DNCE

2
2
3
2
3
3
3
3

10

20

3
3
3
34
35

M10

-LS
-BS
-P

-Q

-Q
-K8
-K3
-P5
-R3
-FG

Additional stroke lengths on request

Only with drive type LS
Only with ball screw spindle BS

Transfer order code

DNCE

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

17

Electric cylinders DNCE, with spindle drive

Accessories
Technical data Internet: eamm-a

Permissible axis/motor combinations with axial kit

Motor/motor unit
Axial kit

Type
DNCE-32
With servo motor
EMME-AS-40-
EMMS-AS-40-
EMMS-AS-55-
EMME-AS-60-
EMME-AS-60-
With stepper motor
EMMS-ST-42-
EMMS-ST-57-
With motor unit
MTR-DCI-32S-2)
DNCE-40
With servo motor
EMMS-AS-55-
EMME-AS-60-
EMMS-AS-70-
With servo motor and gear unit
EMME-AS-40-
EMGA-40-P-G-EAS-40
EMMS-AS-40-
EMGA-40-P-G-SAS-40
With stepper motor
EMMS-ST-57-
EMMS-ST-87-
With stepper motor and gear unit
EMMS-ST-42-
EMGA-40-P-G-SST-42
With motor unit
MTR-DCI-42S--G72)
MTR-DCI-42S--G142)
1)
2)

18

Part No.

Type

1976465
2207372
543147
1322178
550979
1322180
1956054
2234020
1956054
2234020

EAMM-A-D32-40P
EAMM-A-D32-40P-S11)
EAMM-A-D32-40A
EAMM-A-D32-40A-S11)
EAMM-A-D32-55A
EAMM-A-D32-55A-S11)
EAMM-A-D32-60P
EAMM-A-D32-60P-S11)
EAMM-A-D32-60P
EAMM-A-D32-60P-S11)

543148
1322179
550980
1322181

EAMM-A-D32-42A
EAMM-A-D32-42A-S11)
EAMM-A-D32-57A
EAMM-A-D32-57A-S11)

543149

EAMM-A-D32-32B

543153
1322182
1977000
2151519
550981
1322185

EAMM-A-D40-55A
EAMM-A-D40-55A-S11)
EAMM-A-D40-60P
EAMM-A-D40-60P-S11)
EAMM-A-D40-70A
EAMM-A-D40-70A-S11)

560282

EAMM-A-D40-40G

560282

EAMM-A-D40-40G

543154
1322183
550982
1322186

EAMM-A-D40-57A
EAMM-A-D40-57A-S11)
EAMM-A-D40-87A
EAMM-A-D40-87A-S11)

560282

EAMM-A-D40-40G

543155
543156

EAMM-A-D40-42B
EAMM-A-D40-42C

With protection class IP65

Only in conjunction with DNCE--LS

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Accessories
Technical data Internet: eamm-a

Permissible axis/motor combinations with axial kit

Motor/motor unit
Axial kit

Type
DNCE-63
With servo motor
EMMS-AS-70-
EMME-AS-80-
EMME-AS-100-
EMMS-AS-100-
With servo motor and gear unit
EMMS-AS-55-
EMGA-60-P-G-SAS-55
EMMS-AS-70-
EMGA-60-P-G-SAS-70
With stepper motor
EMMS-ST-87-
With servo motor and gear unit
EMMS-ST-57-
EMGA-60-P-G-SST-57
With motor unit
MTR-DCI-52S--G72)
MTR-DCI-52S--G142)
1)
2)

Part No.

Type

543161
1322187
1977073
2218564
550983
1322190
550983
1322190

EAMM-A-D60-70A
EAMM-A-D60-70A-S11)
EAMM-A-D60-80P
EAMM-A-D60-80P-S11)
EAMM-A-D60-100A
EAMM-A-D60-100A-S11)
EAMM-A-D60-100A
EAMM-A-D60-100A-S11)

560283

EAMM-A-D60-60G

560283

EAMM-A-D60-60G

543162
1322188

EAMM-A-D60-87A
EAMM-A-D60-87A-S11)

560283

EAMM-A-D60-60G

543163
543164

EAMM-A-D60-52B
EAMM-A-D60-52C

With protection class IP65

Only in conjunction with DNCE--LS

-H-

Note

Depending on the combination of

motor/motor unit and electric cylin
der, it may not be possible to reach
the maximum feed force of the
cylinder.

2014/08 Subject to change

The following tool is available for

sizing:
PositioningDrives
sizing software
www.festo.com

Internet: www.festo.com/catalogue/...

19

Electric cylinders DNCE, with spindle drive

Accessories
Component parts of the axial kit
Axial kit
Consisting of:
Motor flange

Coupling

Coupling housing

Seal set

Part No.
Type

Part No.
Type

Part No.
Type

Part No.
Type

Part No.
Type

543420
EAMC-16-20-6-6
543420
EAMC-16-20-6-6

552156
EAMK-A-D32-32B
552155
EAMK-A-D32-28B

DNCE-32
543149
EAMM-A-D32-32B
543147
EAMM-A-D32-40A
1322178
EAMM-A-D32-40A-S1
1976465
EAMM-A-D32-40P
2207372
EAMM-A-D32-40P-S1
543148
EAMM-A-D32-42A
1322179
EAMM-A-D32-42A-S1
550979
EAMM-A-D32-55A
1322180
EAMM-A-D32-55A-S1
550980
EAMM-A-D32-57A
1322181
EAMM-A-D32-57A-S1
1956054
EAMM-A-D32-60P
2234020
EAMM-A-D32-60P-S1

20

552163
EAMF-A-28B-40A

1976704
EAMF-A-28B-40P

552164
EAMF-A-28B-42A

529942
EAMF-A-44A/B-55A

530081
EAMF-A-44A/B-57A

1956846
EAMF-A-44C-60P

1232854
EAMC-16-20-6-8

543419
EAMC-16-20-5-6

551003
EAMC-30-32-6-9

551002
EAMC-30-32-6-6.35

1233256
EAMC-30-32-6-14

552155
EAMK-A-D32-28B

552155
EAMK-A-D32-28B

551006
EAMK-A-D32-44A/C

551006
EAMK-A-D32-44A/C

551006
EAMK-A-D32-44A/C

1561526
EADS-F-D32-40A

2207219
EADS-F-D32-40P

1561527
EADS-F-D32-42A

1561528
EADS-F-D32-55A

1561529
EADS-F-D32-57A

2234012
EADS-F-D32-60P

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Accessories
Component parts of the axial kit
Axial kit
Consisting of:
Motor flange

Coupling

Coupling housing

Seal set

Part No.
Type

Part No.
Type

Part No.
Type

Part No.
Type

Part No.
Type

543422
EAMC-30-32-8-8
543422
EAMC-30-32-8-8
543423
EAMC-30-32-8-9

552158
EAMK-A-D40-42B
552159
EAMK-A-D40-42C
552157
EAMK-A-D40-44A/C

DNCE-40
543155
EAMM-A-D40-42B
543156
EAMM-A-D40-42C
543153
EAMM-A-D40-55A
1322182
EAMM-A-D40-55A-S1
543154
EAMM-A-D40-57A
1322183
EAMM-A-D40-57A-S1
1977000
EAMM-A-D40-60P
2151519
EAMM-A-D40-60P-S1
550981
EAMM-A-D40-70A
1322185
EAMM-A-D40-70A-S1
550982
EAMM-A-D40-87A
1322186
EAMM-A-D40-87A-S1
560282
EAMM-A-D40-40G

2014/08 Subject to change

529942
EAMF-A-44A/B-55A

530081
EAMF-A-44A/B-57A

1956846
EAMF-A-44C-60P

529943
EAMF-A-44A/B-70A

530082
EAMF-A-44A/B-87A

550986
EAMF-44A/B-40G

543421
EAMC-30-32-6.35-8

562682
EAMC-30-32-8-14

551004
EAMC-30-32-8-11

551004
EAMC-30-32-8-11

558029
EAMC-30-32-8-10

552157
EAMK-A-D40-44A/C

552157
EAMK-A-D40-44A/C

552157
EAMK-A-D40-44A/C

552157
EAMK-A-D40-44A/C

552157
EAMK-A-D40-44A/C

Internet: www.festo.com/catalogue/...

1561530
EADS-F-D40-55A

1561531
EADS-F-D40-57A

2151545
EADS-F-D40-60P

1561532
EADS-F-D40-70A

1561533
EADS-F-D40-87A

21

Electric cylinders DNCE, with spindle drive

Accessories
Component parts of the axial kit
Axial kit
Consisting of:
Motor flange

Coupling

Coupling housing

Seal set

Part No.
Type

Part No.
Type

Part No.
Type

Part No.
Type

Part No.
Type

533709
EAMC-42-50-12-12
533709
EAMC-42-50-12-12
543424
EAMC-42-50-11-12

552161
EAMK-A-D60-52B
552162
EAMK-A-D60-52C
552160
EAMK-A-D60-64B

DNCE-63
543163
EAMM-A-D60-52B
543164
EAMM-A-D60-52C
543161
EAMM-A-D60-70A
1322187
EAMM-A-D60-70A-S1
1977073
EAMM-A-D60-80P
2218564
EAMM-A-D60-80P-S1
543162
EAMM-A-D60-87A
1322188
EAMM-A-D60-87A-S1
550983
EAMM-A-D60-100A
1322190
EAMM-A-D60-100A-S1
560283
EAMM-A-D60-60G

22

529945
EAMF-A-64A/B-70A

1977113
EAMF-A-64A/C-80P

533140
EAMF-A-64A/B-87A

529947
EAMF-A-64A/C/D-100A

550987
EAMF-A-64A/B-60G/H

551005
EAMC-42-50-12-19

543424
EAMC-42-50-11-12

551005
EAMC-42-50-12-19

543424
EAMC-42-50-11-12

Internet: www.festo.com/catalogue/...

551007
EAMK-A-D60-64C

552160
EAMK-A-D60-64B

551007
EAMK-A-D60-64C

552160
EAMK-A-D60-64B

8022145
EADS-F-D60-70A

2218523
EADS-F-D60-80P

1561536
EADS-F-D60-87A

2253507
EADS-F-D60-100A

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Accessories
Technical data Internet: eamm-u

Permissible axis/motor combinations with parallel kit

Motor/motor unit
Parallel kit
 Space-saving gravity die-cast housing

Type

Part No.

Type

DNCE-32
With servo motor
EMMS-AS-40-
With motor unit
MTR-DCI-32S-

543150

EAMM-U-D32-40A

543152

EAMM-U-D32-32B

543157

EAMM-U-D40-55A

543159
543160

EAMM-U-D40-42B
EAMM-U-D40-42C

543165

EAMM-U-D60-70A

543167
543168

EAMM-U-D60-52B
EAMM-U-D60-52C

DNCE-40
With servo motor
EMMS-AS-55-
With motor unit
MTR-DCI-42S---G7
MTR-DCI-42S--G14
DNCE-63
With servo motor
EMMS-AS-70-
With motor unit
MTR-DCI-52S--G7
MTR-DCI-52S--G14

-H-

Note

Depending on the combination of

motor/motor unit and electric cylin
der, it may not be possible to reach
the maximum feed force of the
cylinder.
The respective no-load driving torque
of the kit must be taken into consid
eration when using parallel kits.

2014/08 Subject to change

The following tool is available for

sizing:
PositioningDrives
sizing software
www.festo.com

Internet: www.festo.com/catalogue/...

23

Electric cylinders DNCE, with spindle drive

Accessories
Technical data Internet: eamm-u

Permissible axis/motor combinations with parallel kit

Motor/motor unit
Parallel kit




Type
DNCE-32
With servo motor
EMME-AS-40-
EMMS-AS-40-
EMMS-AS-55-
With stepper motor
EMMS-ST-42-
EMMS-ST-57-
With motor unit
MTR-DCI-32S-
MTR-DCI-42S-
With gear unit2)
EMGA-40-P-
EMGC-40-P-
DNCE-40
With servo motor
EMMS-AS-55-
EMMS-AS-70-
With stepper motor
EMMS-ST-57-
EMMS-ST-87-
With motor unit
MTR-DCI-42S-
MTR-DCI-52S-
With gear unit2)
EMGA-40-P-
EMGC-40-P-
EMGA-60-P--SAS/SST
EMGA-60-P--EAS
EMGC-60-P-
1)
2)

24

Part No.

Type

2153283
2154009
1201591
1202302
1210126
1210450

EAMM-U-50-D32-40P-78
EAMM-U-50-D32-40P-78-S1 1)
EAMM-U-50-D32-40A-78
EAMM-U-50-D32-40A-78-S1 1)
EAMM-U-60-D32-55A-91
EAMM-U-60-D32-55A-91-S1 1)

1201607
1202312
1210419
1210453

EAMM-U-50-D32-42A-78
EAMM-U-50-D32-42A-78-S1 1)
EAMM-U-60-D32-57A-91
EAMM-U-60-D32-57A-91-S1 1)

1570862
1577393
1577380

EAMM-U-50-D32-32B-78
EAMM-U-60-D32-42B/C-91
EAMM-U-60-D32-42B/C-91-S1 1)

1577358
1577346

EAMM-U-60-D32-40G-91
EAMM-U-60-D32-40G-91-S1 1)

1210438
1210458
1212826
1212854

EAMM-U-60-D40-55A-91
EAMM-U-60-D40-55A-91-S1 1)
EAMM-U-86-D40-70A-102
EAMM-U-86-D40-70A-102-S1 1)

1210442
1210462
1215802
1215814

EAMM-U-60-D40-57A-91
EAMM-U-60-D40-57A-91-S1 1)
EAMM-U-86-D40-87A-102
EAMM-U-86-D40-87A-102-S1 1)

1570950
1430735
1537046
1537011

EAMM-U-60-D40-42B/C-91
EAMM-U-60-D40-42B/C-91-S1 1)
EAMM-U-86-D40-52B/C-102
EAMM-U-86-D40-52B/C-102-S1 1)

1577165
1435968
1586445
1586429
1586496
1586372

EAMM-U-60-D40-40G-91
EAMM-U-60-D40-40G-91-S1 1)
EAMM-U-86-D40-60G-102
EAMM-U-86-D40-60G-102-S1 1)
EAMM-U-86-D40-60H-102
EAMM-U-86-D40-60H-102-S1 1)

Increased housing rigidity

Flexible motor connection possible
Optionally with protection class IP65
Use in combination with third-party motors on request

With protection class IP65

The output torque at the gear unit output must be less than the transferable torque of the kit.

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Accessories
Technical data Internet: eamm-u

Permissible axis/motor combinations with parallel kit

Motor/motor unit
Parallel kit




Type
DNCE-63
With servo motor
EMMS-AS-70-
EMME-AS-80-
EMME-AS-100-
EMMS-AS-100-
With stepper motor
EMMS-ST-87-
With motor unit
MTR-DCI-52S-
MTR-DCI-62S-
With gear unit2)
EMGA-60-P--SAS/SST
EMGA-60-P--EAS
EMGC-60-P-
EMGA-60-P--SAS/SST
EMGA-60-P--EAS
EMGC-60-P-
EMGA-80-P-

1)
2)

Increased housing rigidity

Flexible motor connection possible
Optionally with protection class IP65
Use in combination with third-party motors on request

Part No.

Type

1212477
1212835
2155875
2156527
1202436
1203112
1202436
1203112

EAMM-U-86-D60-70A-102
EAMM-U-86-D60-70A-102-S1 1)
EAMM-U-86-D60-80P-102
EAMM-U-86-D60-80P-102-S1 1)
EAMM-U-110-D60-100A-120
EAMM-U-110-D60-100A-120-S1 1)
EAMM-U-110-D60-100A-120
EAMM-U-110-D60-100A-120-S1 1)

1215784
1215810

EAMM-U-86-D60-87A-102
EAMM-U-86-D60-87A-102-S1 1)

1537000
1431381
1536988
1431443

EAMM-U-86-D60-52B/C-102
EAMM-U-86-D60-52B/C-102-S1 1)
EAMM-U-110-D60-62B-120
EAMM-U-110-D60-62B-120-S1 1)

1586347
1437163
1586276
1530837
1543240
1436183
1542264
1530621
1532949
1530875

EAMM-U-86-D60-60G-102
EAMM-U-86-D60-60G-102-S1 1)
EAMM-U-86-D60-60H-102
EAMM-U-86-D60-60H-102-S1 1)
EAMM-U-110-D60-60G-120
EAMM-U-110-D60-60G-120-S1 1)
EAMM-U-110-D60-60H-120
EAMM-U-110-D60-60H-120-S1 1)
EAMM-U-110-D60-80G-120
EAMM-U-110-D60-80G-120-S1 1)

With protection class IP65

The output torque at the gear unit output must be less than the transferable torque of the kit.

-H-

Note

The clamping component EADT is

required to adjust the toothed belt
pretension with EAMM-U-110.

2014/08 Subject to change

The motor and/or axis shaft can op

tionally be supported with a counter
bearing EAMG.
More information eamm-u

Internet: www.festo.com/catalogue/...

25

Electric cylinders DNCE, with spindle drive

Accessories
Bellows kit EADB

General technical data

Type EADB-V1-

32

Max. stroke range of cylinder1)

Type of mounting

[mm]

Mounting position
Resistance to media
Ambient temperature2)
Protection class to IEC 60529
Corrosion resistance class CRC3)
1)
2)
3)

[C]

40

63

10 400
10 500
Push on
Via threaded pin
Any
Dust, chippings, oil, grease, fuel ( Internet: Resistance to media)
10 +80
IP65
3

10 500

In combination with the bellows kit EADB

Note operating range of proximity sensors and cylinder
Corrosion resistance class 3 according to Festo standard 940 070
Components subject to high corrosion stress. External visible parts in direct contact with industrial atmospheres or media such as solvents and cleaning agents, with a predominantly functional requirement for the
surface.

Materials
Sectional view
1

Bellows
1
2
3
4

Weight [g]
Type EADB-V1Stroke [mm]

Connection
Adapter
Bellows
End piece
O-ring
Note on materials

Anodised wrought aluminium alloy

Polyamide
Nitrile rubber
Anodised wrought aluminium alloy
Nitrile rubber
Free of copper and PTFE
Conforms to RoHS

32

40

63

Product weight
10 100
101 200
201 300
301 400
401 500

77
108
122
153

116
153
172
209
227

196
263
309
376
397

Moving load
10 100
101 200
201 300
301 400
401 500

35
66
80
111

43
80
99
136
154

86
153
199
266
287

26

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Accessories
Travel speed v as a function of tubing length l
The bellows kit is a leak-free system.
To prevent unwanted media from be
ing drawn in, the supply and exhaust
air must be ducted via a pressure
compensation hole in the connection

part 1.
The pressure generated in the bellows
kit by the positioning motion is
primarily defined by the travel speed

and tubing length. The recommended

tubing length based on the travel
speed of the drive can be read from
the graph.

EADB-V1-32/tubing 8 mm
EADB-V1-40/tubing 16 mm
EADB-V1-63/tubing 16 mm

-H-

Note

The push-in fittings opposite must be

used for the pressure compensation
hole.

Silencers can be used as an

alternative. This reduces the travel
speed slightly.

Tubing length and push-in fitting for pressure compensation hole

Tubing O.D.
Push-in fitting
[mm]
[mm]
Part No. Type
32

40, 63

16

186109
578376
186350
578344
153261

Download CAD data www.festo.com

Dimensions

Stroke
[mm]

A21)

10 100
101 200
201 300
301 400
401 500

44
74
88
117

D1
max.

Stroke
[mm]

A21)

10 100
101 200
201 300
301 400
401 500

43
68
80
104
117

1)

QS-Gx-8-I
NPQH-DK-G18-Q8-P10
QS-G-12
NPQH-D-G14-Q12-P10
QSH-16-12

32
EE

D2

L1

L2

46

14

Gx

12.9

5.4

D1
max.

93

D2

17

WH+A2

A21)

70
100
114
143

48
77
88
117
135
63
EE

D1
max.

D2

57

17

L1

22.4

= plus stroke length

40
EE

L1

16.3

L2

WH+A2

78
107
118
147
165

L2

WH+A2

80
105
117
141
154

The dimension corresponds to the K8 value (extended piston rod) of the cylinder

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

27

Electric cylinders DNCE, with spindle drive

Accessories
Ordering data Bellows kit
An extended piston rod
(order code K8) 17 is absolutely
necessary when using a bellows kit.

Cylinder data

Stroke

The necessary dimensions for K8 as a

function of cylinder size and stroke as
well as the corresponding bellows kit
are indicated in the table below:

Bellows kit
Dimension Part No.
Type
for K8
[mm]

Cylinder data

Stroke
[mm]

[mm]

Bellows kit
Dimension Part No. Type
for K8
[mm]

40

10 100
101 200
201 300
301 400
401 500

48
77
88
117
135

[mm]

[mm]

32

10 100
101 200
201 300
301 400

44
74
88
117

570262
570263
570264
570265

EADB-V1-32-S10-100
EADB-V1-32-S101-200
EADB-V1-32-S201-300
EADB-V1-32-S301-400

63

10 100
101 200
201 300
301 400
401 500

43
68
80
104
117

570271
570272
570273
570274
570275

EADB-V1-63-S10-100
EADB-V1-63-S101-200
EADB-V1-63-S201-300
EADB-V1-63-S301-400
EADB-V1-63-S401-500

28

Order example:
Selected electric cylinder:
DNCE-32-250-BS-3P-Q-K8
The dimension for the corresponding K8 value (see table):
88 mm
Complete type code for electric cylinder:
DNCE-32-250-BS-3P-Q-88K8
The corresponding bellows kit:
EADB-V1-32-S201-300

Internet: www.festo.com/catalogue/...

570266
570267
570268
570269
570270

EADB-V1-40-S10-100
EADB-V1-40-S101-200
EADB-V1-40-S201-300
EADB-V1-40-S301-400
EADB-V1-40-S401-500

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Accessories
Material:
Galvanised steel

Foot mounting HNCE,

for axial motor mounting

Free of copper and PTFE

+ = plus stroke length

1 See dimensions for HNC
2 Electric cylinder DNCE
Dimensions and ordering data
For size
AB

[mm]
32
40
63

7
10
10

For size

CRC1)

[mm]
32
40
63
1)

Weight

3 Axial kit EAMM-A

4 Servo motor

AH

AO

AT

AU

SA

TR

US

XA

XS

32
36
50

10.5
12.5
15

4
4
5

17.5
19.5
23

163.5
194.5
232

58
72
92

71
90
110

165.5
196
237

46
54
64

Part No.

Type

547949
547950
547951

HNCE-32-AX
HNCE-40-AX
HNCE-63-AX

[g]
1
1
1

160
220
470

Corrosion resistance class 1 according to Festo standard 940 070

Components subject to low corrosion stress. Transport and storage protection. Parts that do not have primarily decorative surface requirements, e.g. in internal areas that are not visible or behind covers.

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

29

Electric cylinders DNCE, with spindle drive

Accessories
Materials:
Plate: Anodised aluminium
Clamping pieces: Galvanised steel

Profile mounting EAHF

Dimensions and ordering data

For size
AH

RoHS-compliant

B1

B2

B3

D1

H1

H2

L1

100
130
150

84
108
128

66.1
85.2
104.8

6.6
9
9

17.5
15.7
22.9

26.1
23.3
30.4

32
34
41

[mm]
32
40
63

32
36
50

For size

CRC1)

[mm]
32
40
63
1)

30

Weight

Part No.

Type

[g]
1
1
1

175
230
400

1098473 EAHF-V1-32-P
1098478 EAHF-V1-40-P
1098481 EAHF-V1-63-P

Corrosion resistance class 1 according to Festo standard 940 070

Components subject to low corrosion stress. Transport and storage protection. Parts that do not have primarily decorative surface requirements, e.g. in internal areas that are not visible or behind covers.

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Accessories
Material:
HNC: Galvanised steel
CRHNC: High-alloy steel

Foot mounting HNC/CRHNC,

for parallel motor mounting

Free of copper and PTFE

+ = plus stroke length

2 Electric cylinder DNCE
3 Parallel kit EAMM-U
Dimensions and ordering data
For size
AB

[mm]
32
40
63

7
10
10

For size

4 Motor unit MTR-DCI

AH

AO

AT

AU

SA

TR

US

XA

XS

32
36
50

6.5
9
12.5

4
4
5

24
28
32

210
249.5
299

32
36
50

45
54
75

212
251.5
304

46
54
64

Part No.

Type

High corrosion protection

CRC1)
Weight
Part No.
[g]

Type

[mm]

Basic version
CRC1)
Weight
[g]

32
40
63

2
2
2

174369
174370
174372

HNC-32
HNC-40
HNC-63

4
4
4

CRHNC-32
CRHNC-40
CRHNC-63

1)

144
193
436

139
188
424

176937
176938
176940

Corrosion resistance class 2 according to Festo standard 940 070

Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or
lubricating agents.
Corrosion resistance class 4 according to Festo standard 940 070
Components subject to particularly high corrosion stress. Parts used with aggressive media, e.g. in the food or chemical industry. These applications should be supported with special tests with the media if required.

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

31

Electric cylinders DNCE, with spindle drive

Accessories
Material:
FNC: Galvanised steel
CRFNG: High-alloy steel

Flange mounting FNC/CRFNG

Free of copper and PTFE

RoHS-compliant

2 Electric cylinder DNCE

3 Parallel kit EAMM-U
Dimensions and ordering data
For size
E
[mm]
32
40
63

45
54
75

For size

4 Motor unit MTR-DCI

+ = plus stroke length

The flange mounting FNC/CRFNG can only be

mounted on the parallel kits on page 23

FB

H13

MF

TF

UF

ZF

7
9
9

10
10
12

32
36
50

64
72
100

80
90
120

16
20
25

198
233.5
284

Part No.

Type

High corrosion protection

CRC1)
Weight
Part No.
[g]

Type

[mm]

Basic version
CRC1)
Weight
[g]

32
40
63

1
1
1

174376
174377
174379

FNC-32
FNC-40
FNC-63

4
4
4

CRFNG-32
CRFNG-40
CRFNG-63

1)

32

221
291
679

225
300
680

161846
161847
161849

Corrosion resistance class 1 according to Festo standard 940 070

Components subject to low corrosion stress. Transport and storage protection. Parts that do not have primarily decorative surface requirements, e.g. in internal areas that are not visible or behind covers.
Corrosion resistance class 4 according to Festo standard 940 070
Components subject to particularly high corrosion stress. Parts used with aggressive media, e.g. in the food or chemical industry. These applications should be supported with special tests with the media if required.

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Accessories
Material:
ZNCF: Stainless steel casting
CRZNG: Electropolished stainless steel
casting

Trunnion flange ZNCF/CRZNG

2 Electric cylinder DNCE

3 Parallel kit EAMM-U
Dimensions and ordering data
For size
C2

71
87
116

For size

4 Motor unit MTR-DCI

+ = plus stroke length

C3

TD

e9

TK

TL

TM

US

XH

XL

86
105
136

12
16
20

16
20
24

12
16
20

50
63
90

45
54
75

18
20
25

196
233.5
284

[mm]
32
40
63

Free of copper and PTFE

RoHS-compliant

Part No.

Type

High corrosion protection

CRC1)
Weight
Part No.
[g]

Type

[mm]

Basic version
CRC1)
Weight
[g]

32
40
63

2
2
2

174411
174412
174414

ZNCF-32
ZNCF-40
ZNCF-63

4
4
4

CRZNG-32
CRZNG-40
CRZNG-63

1)

150
285
687

150
285
687

161852
161853
161855

Corrosion resistance class 2 according to Festo standard 940 070

Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or
lubricating agents.
Corrosion resistance class 4 according to Festo standard 940 070
Components subject to particularly high corrosion stress. Parts used with aggressive media, e.g. in the food or chemical industry. These applications should be supported with special tests with the media if required.

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

33

Electric cylinders DNCE, with spindle drive

Accessories
Trunnion support LNZG
Materials:
Trunnion support: Anodised
aluminium
Plain bearing: Plastic
Free of copper and PTFE
RoHS-compliant

Dimensions and ordering data

For size
CR
DA

[mm]
D11 H13
32
40
63

12
16
20

11
15
18

FK

0.1

FN

15
18
20

30
36
40

FS

H1

10.5
12
13

15
18
20

FS

H1

HB

H13

KE

6.6
9
11

6.8
9
11

NH

TH

UL

CRC1)

0.2
18
21
23

32
36
42

Weight

Part No.

Type

[g]
46
55
65

2
2
2

83
129
178

32959
32960
32961

LNZG-32
LNZG-40/50
LNZG-63/80

CRC1)

Weight

Part No.

Type

161874
161875
161876

CRLNZG-32
CRLNZG-40/50
CRLNZG-63/80

Trunnion support CRLNZG

Material:
High-alloy steel
Free of copper and PTFE
RoHS-compliant

Dimensions and ordering data

For size
CR
FK

[mm]
D11
0.1
32
40
63
1)

34

12
16
20

15
18
20

FN

30
36
40

10.5
12
13

15
18
20

HB

H13

NH

6.6
9
11

18
21
23

TH

UL

0.2
32
36
42

[g]
46
55
65

4
4
4

205
323
435

Corrosion resistance class 2 according to Festo standard 940 070

Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or
lubricating agents.
Corrosion resistance class 4 according to Festo standard 940 070
Components subject to particularly high corrosion stress. Parts used with aggressive media, e.g. in the food or chemical industry. These applications should be supported with special tests with the media if required.

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Accessories
Material:
Die-cast aluminium

Swivel flange SNC

Free of copper and PTFE

RoHS-compliant

1 The king pin is protected

against rotation with a spring
pin
Dimensions and ordering data
For size
CG

CP

EK

[mm]

H14

h14

32
40
63

14
16
21

34
40
51

FL

2 Electric cylinder DNCE

3 Parallel kit EAMM-U
4 Motor unit MTR-DCI

SR

XC

13
16
21

10
12
16

210
248.5
304

0.2
10
12
16

32
40
63
1)

10+0.013
12+0.015
16+0.015

EP

EX

+0.2
45+0.2/0.5
540.5
750.6

10.5
12
15

Type

2
2
2

90
120
320

174383
174384
174386

SNC-32
SNC-40
SNC-63

FL

Weight

Part No.

Type

174397
174398
174400

SNCS-32
SNCS-40
SNCS-63

4 Motor unit MTR-DCI

+ = plus stroke length

LT

MS

RA

13
16
21

15+0.5
17+0.5
230.5

14.5
17.5
23

0.2
14
16
21

Part No.

Free of copper and PTFE

RoHS-compliant

2 Electric cylinder DNCE

3 Parallel kit EAMM-U
Dimensions and ordering data
For size
CN

[mm]

Weight

= plus stroke length

[g]

22
25
32

Material:
Die-cast aluminium

Swivel flange SNCS

CRC1)

22
25
32

TG

XC

32.5
38
56.5

210
248.5
304

CRC1)

+1

[g]
2
2
2

86
122
281

Corrosion resistance class 2 according to Festo standard 940 070

Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or
lubricating agents.

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

35

Electric cylinders DNCE, with spindle drive

Accessories
Material:
Die-cast aluminium

Swivel flange SNCL

Free of copper and PTFE

RoHS-compliant

2 Electric cylinder DNCE

3 Parallel kit EAMM-U
Dimensions and ordering data
For size
CD

[mm]
H9

EW

FL

h12

0.2

32
40
63

26
28
40

22
25
32

1)

36

10
12
16

4 Motor unit MTR-DCI

+ = plus stroke length

MR

XC

CRC1)

Weight

Part No.

Type

174404
174405
174407

SNCL-32
SNCL-40
SNCL-63

[g]
13
16
21

10
12
16

210
248.5
304

2
2
2

75
100
250

Corrosion resistance class 2 according to Festo standard 940 070

Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or
lubricating agents.

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Accessories
Material:
SNCB: Die-cast aluminium
SNCB--R3: Die-cast aluminium with
protective coating, high corrosion
protection

Swivel flange
SNCB/SNCB--R3

2 Electric cylinder DNCE

3 Parallel kit EAMM-U
Dimensions and ordering data
For size
CB
[mm]

H14

EK

e8

32
40
63

26
28
40

10
12
16

For size

Free of copper and PTFE

RoHS-compliant

4 Motor unit MTR-DCI

+ = plus stroke length

FL
0.2
22
25
32

MR

13
16
21

10
12
16

UB
h14
45
52
70

Part No.

Type

[mm]

Basic version
CRC1)
Weight
[g]

Variant R3 High corrosion protection

CRC1)
Weight
Part No.
Type
[g]

32
40
63

2
2
2

174390
174391
174393

SNCB-32
SNCB-40
SNCB-63

3
3
3

1)

103
155
375

XC

100
151
371

176944
176945
176947

210
248.5
304

SNCB-32-R3
SNCB-40-R3
SNCB-63-R3

Corrosion resistance class 2 according to Festo standard 940 070

Components subject to moderate corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as coolants or
lubricating agents.
Corrosion resistance class 3 according to Festo standard 940 070
Components subject to high corrosion stress. Externally visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment or media such as solvents and
cleaning agents.

2014/08 Subject to change

Internet: www.festo.com/catalogue/...

37

Electric cylinders DNCE, with spindle drive

Accessories
Material:
Galvanised steel
Free of copper and PTFE

Trunnion mounting kit ZNCM

The mounting kit can be attached at

any position along the profile barrel of
a cylinder.
The trunnion mounting kit cannot be

1 Max. tightening torque

2 Electric cylinder DNCE
Dimensions and ordering data
For size
B1

30
32
41

For size

C3

TD

e9

TL

TM

UW

XG

71
87
116

86
105
136

12
16
20

12
16
20

50
63
90

65
75
105

65
74.5
91.5

XJ

XV

107
130.5
157.5

86
102.5
124.5

[mm]
32
40
63
1)

Max.
tightening torque
[Nm]

CRC1)

4+1
8+1
18+2

1
1
1

Weight

Part No.

Type

2213233
2214899
2214971

DAMT-V1-32-A
DAMT-V1-40-A
DAMT-V1-63-A

[g]
213
388
911

Corrosion resistance class 1 according to Festo standard 940 070

Components subject to low corrosion stress. Transport and storage protection. Parts that do not have primarily decorative surface requirements, e.g. in internal areas that are not visible or behind covers.

Ordering data Mounting attachments

Designation
For size
Part No.

Type

Clevis foot LNG

Designation

For size

Technical data Internet: clevis foot

Part No.
Type

32
40
63

5561
5562
5564

LSN-32
LSN-40
LSN-63

Clevis foot LSN

32
40
63

33890
33891
33893

LNG-32
LNG-40
LNG-63

32
40
63

31740
31741
31743

LSNG-32
LSNG-40
LSNG-63

Clevis foot LSNSG

32
40
63

31747
31748
31750

LSNSG-32
LSNSG-40
LSNSG-63

32
40
63

31761
31762
31764

LBG-32
LBG-40
LBG-63

Right-angle clevis foot LQG

32
40
63

31768
31769
31771

LQG-32
LQG-40
LQG-63

Clevis foot LSNG

Clevis foot LBG

38

+ = plus stroke length

+ = plus stroke length

C2

[mm]
32
40
63

3 Axial kit EAMM-A

mounted in the vicinity of the motor

when used in combination with the
parallel kit EAMM-U.

Internet: www.festo.com/catalogue/...

Subject to change 2014/08

Electric cylinders DNCE, with spindle drive

Accessories
Ordering data Mounting attachments, corrosion-resistant
Designation
For size

Technical data Internet: clevis foot

Part No.
Type

Clevis foot CRLNG

32
40
63

161840
161841
161843

Ordering data Piston rod attachments

Designation
For size
Part No.

Type

Designation

Rod eye SGS

For size

CRLNG-32
CRLNG-40
CRLNG-63

Technical data Internet: piston rod attachment

Part No.
Type

Rod clevis SGA

32
40
63

9261
9262
9263

SGS-M10x1,25
SGS-M12x1,25
SGS-M16x1,5

32
40
63

6144
6145
6146

SG-M10x1,25
SG-M12x1,25
SG-M16x1,5

36125
36126
36127

KSZ-M10x1,25
KSZ-M12x1,25
KSZ-M16x1,5

Rod clevis SG

Coupling piece KSZ

32
40
63

32
40
63
Self-aligning rod coupler FK
32
40
63

Ordering data Piston rod attachments, corrosion-resistant

Designation
For size
Part No.
Type

Designation

Rod eye CRSGS

Rod clevis CRSG

32
40
63

Self-aligning rod coupler CRFK

32
40
63

195582
195583
195584

CRSGS-M10x1,25
CRSGS-M12x1,25
CRSGS-M16x1,5

2305778
2305779
2490673

CRFK-M10x1,25
CRFK-M12x1,25
CRFK-M16x1,5

32
40
63

Ordering data Guide units for fixed strokes (recirculating ball bearing guide only)
Stroke
Part No. Type
Stroke
[mm]
[mm]
For size 32
10 100
10 200
10 320
10 400
10 500

34494
34496
34497
150290
34498

FENG-32-100-KF
FENG-32-200-KF
FENG-32-320-KF
FENG-32-400-KF
FENG-32-500-KF

For size 63
10 100
10 200
10 320
10 400
10 500

34514
34516
34518
34519
34520

FENG-63-100-KF
FENG-63-200-KF
FENG-63-320-KF
FENG-63-400-KF
FENG-63-500-KF

2014/08 Subject to change

For size

For size 40
10 100
10 200
10 320
10 400
10 500

32954
10767
10768

SGA-M10x1,25
SGA-M12x1,25
SGA-M16x1,5

6140
6141
6142

FK-M10x1,25
FK-M12x1,25
FK-M16x1,5

Technical data Internet: piston rod attachment

Part No.
Type
13569
13570
13571

CRSG-M10x1,25
CRSG-M12x1,25
CRSG-M16x1,5

Technical data Internet: feng

Part No.

Type

34500
34502
34504
150291
34505

FENG-40-100-KF
FENG-40-200-KF
FENG-40-320-KF
FENG-40-400-KF
FENG-40-500-KF

Internet: www.festo.com/catalogue/...

39

Electric cylinders DNCE, with spindle drive

Accessories
Ordering data Guide units for variable strokes
For size
Stroke
[mm]
[mm]
32
40
63

10 500
10 500
10 500

With recirculating ball bearing guide

Part No.
Type

Technical data Internet: feng

With plain-bearing guide
Part No.
Type

34487
34488
34490

34481
34482
34484

FENG-32-
FENG-40-
FENG-63-

Part No.

Type

570305
570306
570307

EADC-V1-32
EADC-V1-40
EADC-V1-50/63

FENG-32--KF
FENG-40--KF
FENG-63--KF

Ordering data Compensating elements in combination with guide unit FENG

Designation
For size
32
40
63

Permissible proximity sensors in combination with motor units MTR-DCI

Ordering data Proximity sensors for T-slot, magneto-resistive
Type of mounting
Switching
output

Electrical connection

Cable length
[m]

Part No.

Technical data Internet: smt

Type

Plug M8x1, 3-pin

0.3

574334

SMT-8M-A-PS-24V-E-0,3-M8D

N/O contact
Insertable in the slot from above, flush
with cylinder profile, short design

PNP

Permissible proximity sensors in combination with servo motors EMMS-AS, stepper motors EMMS-ST or guide units FENG

Electrical connection

Cable length
[m]

Part No.

Technical data Internet: smt

Type

Cable, 3-wire

2.5

574335

SMT-8M-A-PS-24V-E-2,5-OE

Electrical connection

Cable length
[m]

Part No.

Technical data Internet: sme

Type

Cable, 3-wire

2.5

543862

SME-8M-DS-24V-K-2,5-OE

5.0

543863

SME-8M-DS-24V-K-5,0-OE

2.5

150855

SME-8-K-LED-24

Connection

Cable length
[m]

Part No.

Technical data Internet: km8

Type

3-pin

0.5
1
2.5
5

175488
175489
165610
165611

KM8-M8-GSGD-0,5
KM8-M8-GSGD-1
KM8-M8-GSGD-2,5
KM8-M8-GSGD-5

Length

Part No.

Type

2x 0.5 m

151680

ABP-5-S

Ordering data Proximity sensors for T-slot, magneto-resistive

Type of mounting
Switching
output
N/O contact
Insertable in the slot from above, flush
with cylinder profile, short design

PNP

Ordering data Proximity sensors for T-slot, magnetic reed

Type of mounting
Switching
output
N/O contact
Insertable in the slot from above, flush
with the cylinder profile

Contacting

Insertable in the slot lengthwise, flush

with the cylinder profile

Contacting

Ordering data Connecting cable

Assembly

Cable, 3-wire

Straight socket
Union nut M8, both ends

Ordering data Slot cover for T-slot

Assembly
Insertable from above

40

Internet: www.festo.com/catalogue/...

Subject to change 2014/08