0% found this document useful (0 votes)
327 views2 pages

Splice Connection Design by Aij

This document provides design parameters and procedures for splice connection design. It specifies Japanese Industrial Standards for bolt grades of S10T high strength bolts with yield strengths of 900 MPa and tensile strengths of 1000 MPa. It also specifies JIS steel grades for the bolted components with yield strengths of 235 MPa and tensile strengths of 400 MPa. The design code follows AIJ standards. Tables provide bolt capacities for single and double shear configurations for various bolt diameters. Strength check calculations are outlined to determine the required allowable member strengths based on 70% of maximum strength, and to check the bolt and plate capacities against these required strengths for the flange and web splices.

Uploaded by

dantevarias
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
327 views2 pages

Splice Connection Design by Aij

This document provides design parameters and procedures for splice connection design. It specifies Japanese Industrial Standards for bolt grades of S10T high strength bolts with yield strengths of 900 MPa and tensile strengths of 1000 MPa. It also specifies JIS steel grades for the bolted components with yield strengths of 235 MPa and tensile strengths of 400 MPa. The design code follows AIJ standards. Tables provide bolt capacities for single and double shear configurations for various bolt diameters. Strength check calculations are outlined to determine the required allowable member strengths based on 70% of maximum strength, and to check the bolt and plate capacities against these required strengths for the flange and web splices.

Uploaded by

dantevarias
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

SPLICECONNECTIONDESIGN

1.DesignParameters:
GradeofBolt
:JISB1186FT10TFritctionTyoeHighStrengthBolt
:Torsheartype(S10T)HightStrengthBolt
:Fy=900N/mm 2,Fu=1000N/mm 2

DesignCode :AIJ

Unit:kN
Single
Double
Tension
Diameter ShearCap ShearCap
Cap
(Vbs)
(Vbd)

GradeofSteel

M16
30.2
M20
47.1
M22
57
M24
67
:JISG3101SS400
:Fy=
235
:Fu=
400

TYPE2

60.3
94.2
114
136

62.3
97.4
118
140

N/mm2,
N/mm2,

TYPE1

2.StrengthCheck
2.2WebSplicePlateandWebBoltCapacity
2.1FlangePlateandBoltCapacity
2.1.1RequiredAllowableMemberStrength
(*)
Tcapf= (Fy/1.5*Af)*0.8
(*)70%ofmaximumstrengthisusedas
requiredallowablestrength.

2.2.1RequiredAllowableMemberStrength
(*)
Tcapw= (Fy/1.5*Aw)*0.8
(*)70%ofmaximumstrengthisusedas
requiredallowablestrength.
2.2.2WebBoltCapacity

2.1.2FlangeBoltCapacity
Tbw= Nw*Vbd
Tbf= 2*Nf*Vbd
2.2.3WebPlateYielding
2.1.3FlangePlateYielding
Tpf= Fy/1.5*Agf
Agf= B*t1+2*C*t2

Tpw= Fy/1.5*Agf
Agw= 2*D*t3

You might also like