Unit I Power Semi-Conductor Devices: Topic Sub Topics

KCE/DEPT.OF.
EEE/E-Material
Electronics
Subject Code/Name: EE6503/Power
UNIT I
POWER SEMI-CONDUCTOR DEVICES
INTRODUCTION
Power Electronics is a field which combines Power (electric power), Electronics and
Control systems. Power engineering deals with the static and rotating power equipment
for the generation, transmission and distribution of electric power. Electronics deals
with the study of solid state semiconductor power devices and circuits for Power
conversion to meet the desired control objectives (to control the output voltage and
output power). Power electronics may be defined as the subject of applications of solid
state power semiconductor devices (Thyristors) for the control and conversion of
electric power.
Topic
Sub
Topics
Study of Switching Devices

Brief History of Power Electronics, Power Electronic Applications, Power
Semiconductor Devices
1. STUDY OF SWITCHING DEVICES

1.1 Brief History of Power Electronics
The first Power Electronic Device developed was the Mercury Arc Rectifier during
the year 1900. Then the other Power devices like metal tank rectifier, grid controlled
vacuum tube rectifier, ignitron, phanotron, thyratron and magnetic amplifier, were
developed & used gradually for power control applications until 1950. The first SCR
(silicon controlled rectifier) or Thyristor was invented and developed by Bell Labs in
1956 which was the first PNPN triggering transistor. The second electronic revolution
began in the year 1958 with the development of the commercial grade Thyristor by the
General Electric Company (GE). Thus the new era of power electronics was born. After
that many different types of power semiconductor devices & power conversion
techniques have been introduced. The power electronics revolution is giving us the
ability to convert, shape and control large amounts of power.
1.2 Power Electronic Applications
a) Commercial Applications
Heating Systems Ventilating, Air Conditioners, Central Refrigeration, Lighting,
Computers and Office equipments, Uninterruptible Power Supplies (UPS), Elevators, and
Emergency Lamps.
b) Domestic Applications
Cooking Equipments, Lighting, Heating, Air Conditioners, Refrigerators &
Freezers, Personal Computers, Entertainment Equipments, UPS.
c) Industrial Applications
Pumps, compressors, blowers and fans. Machine tools, arc furnaces, induction
furnaces, lighting control circuits, industrial lasers, induction heating, welding
equipments.
d) Aerospace Applications
Space shuttle power supply systems, satellite power systems, aircraft power
systems.
e) Telecommunications
1
KCE/DEPT.OF.EEE/E-Material
Electronics
Battery chargers, power supplies (DC and UPS), mobile cell phone battery
chargers.
f) Transportation
Traction control of electric vehicles, battery chargers for electric vehicles, electric
locomotives, street cars, trolley buses, automobile electronics including engine
controls.
1.3 POWER SEMICONDUCTOR DEVICES

The power semiconductor devices are used as on/off switches in power control
circuit. These
devices are classified as follows
Part-A Question
1. What are the applications of Power Electronics?
2. What are the classification of power devices?
Topic
Power Semiconductor- Diodes
Sub Topics
Structure, Ton-Toff , V-I Characteristics of Diode
2. (a) POWER SEMICONDUCTOR- DIODES
Introduction
Power semiconductor diode is the power level counter part of the low power
signal diodes with which most of us have some degree of familiarity. These power
devices, however, are required to carry up to several KA of current under forward bias
condition and block up to several KV under reverse biased condition. These extreme
requirements call for important structural changes in a power diode which significantly
affect their operating characteristics. These structural modifications are generic in the
sense that the same basic modifications are applied to all other low power
semiconductor devices (all of which have one or more p-n junctions) to scale up their
power capabilities. It is, therefore, important to understand the nature and implication
of these modifications in relation to the simplest of the power devices, i.e., a power
semiconductor diode.
2
Electronics
2.(a).1 Construction and Characteristics of Power Diodes

As mention in the introduction Power Diodes of largest power rating are required
to conduct several kilo amps of current in the forward direction with very little power
loss while blocking several kilo volts in the reverse direction. Large blocking voltage
requires wide depletion layer in order to restrict the maximum electric field strength
below the impact ionization level. Space charge density in the depletion layer should
also be low in order to yield a wide depletion layer for a given maximum Electric fields
strength. These two requirements will be satisfied in a lightly doped p-n junction diode
of sufficient width to accommodate the required depletion layer. Such a construction,
however, will result in a device with high resistively in the forward direction.
Consequently, the power loss at the required rated current will be unacceptably high.
On the other hand if forward resistance (and hence power loss) is reduced by
increasing the doping level, reverse break down voltage will reduce. This apparent
contradiction in the requirements of a power diode is resolved by introducing a lightly
doped drift layer of required thickness between two heavily doped p and n layers as
shown in Fig (c),Fig (a) and Fig (b) shows the circuit symbol and the photograph of a
typical power diode respectively.
Diagram of a power; (a) circuit symbol (b) photograph (c) schematic cross
section.
To arrive at the structure shown in Fig (c) a lightly doped n- epitaxial layer of
specified width (depending on the required break down voltage) and donor atom
density (NdD) is grown on a heavily doped n+ substrate (NdK donor atoms.Cm -3) which
acts as the cathode. Finally the p-n junction is formed by defusing a heavily doped (N aA
acceptor atoms.Cm-3) p+ region into the epitaxial layer. This p type region acts as the
anode. Impurity atom densities in the heavily doped cathode (Ndk .Cm -3) and anode
(NaA.Cm -3) are approximately of the same order of magnitude (10 19 Cm -3) while that
of the epitaxial layer (also called the drift region) is lower by several orders of
magnitude (NdD ~ 10 14 Cm 3). In a low power diode this drift region is absent.
2.(a).2 Switching Characteristics of Power Diodes
Power Diodes take finite time to make transition from reverse bias to forward bias
condition (switch ON) and vice versa (switch OFF). Behavior of the diode current and
voltage during these switching periods are important due to the following reasons.
Severe over voltage / over current may be caused by a diode switching at
different points in the circuit using the diode.
Voltage and current exist simultaneously during switching operation of a diode.
Therefore, every switching of the diode is associated with some energy loss. At high
3
Electronics
switching frequency this may contribute significantly to the overall power loss in the
diode. Observed Turn ON behavior of a power Diode: Diodes are often used in circuits
with di/dt limiting inductors. The rate of rise of the forward current through the diode
during Turn ON has significant effect on the forward voltage drop characteristics. A
typical turn on transient is shown in Fig.
Forward current and voltage waveforms of a power diode during Turn On

Operation.
It is observed that the forward diode voltage during turn ON may transiently
reach a significantly higher value Vfr compared to the steady slate voltage drop at the
steady current IF. In some power converter circuits (e.g voltage source inverter) where
a freewheeling diode is used across an asymmetrical blocking power switch (i.e GTO)
this transient over voltage may be high enough to destroy the main power switch.VFr
(called forward recovery voltage) is given as a function of the forward di/dt in the
manufacturers data sheet. Typical values lie within the range of 10-30V. Forward
recovery time (tfr) is typically within 10 us.
Observed Turn OFF behavior of a Power Diode:
Fig.shows a typical turn off behavior of a power diode assuming controlled rate of
decrease of the forward current.
Reverse Recovery characteristics of a power diode

Salient features of this characteristic are:
The diode current does not stop at zero, instead it grows in the negative direction to
4
Electronics
Irr called peak reverse recovery current which can be comparable to IF. In many power
electronic circuits (e.g. choppers, inverters) this reverse current flows through the main
power switch in addition to the load current. Therefore, this reverse recovery current
has to be accounted for while selecting the main switch.
Voltage drop across the diode does not change appreciably from its steady state
value till the diode current reaches reverse recovery level. In many power electric
circuits (choppers, inverters) this may create an effective short circuit across the
supply, current being limited only by the stray wiring inductance. Also in high frequency
switching circuits (e.g, SMPS) if the time period t4 is comparable to switching cycle
qualitative modification to the circuit behavior is possible.
Towards the end of the reverse recovery period if the reverse current falls too sharply,
(low value of S), stray circuit inductance may cause dangerous over voltage (Vrr) across
the device. It may be required to protect the diode using an RC snubber.
During the period t5 large current and voltage exist simultaneously in the device.
At high switching frequency this may result in considerable increase in the total power
loss. Important parameters defining the turn off characteristics are, peak reverse
recovery current (Irr), reverse recovery time (trr), reverse recovery charge (Qrr) and the
snappiness factor S. Of these parameters, the snappiness factor S depends mainly on
the construction of the diode (e.g. drift region width, doping lever, carrier life time etc.).
Other parameters are interrelated and also depend on S. Manufacturers usually specify
these parameters as functions of diF/dt for different values of IF. Both Irr and Qrr
increases with IF and diF/dt while trr increases with IF and decreases with diF/dt.
2.(a). 3 Review of Basic p-n Diode Characteristics
A p-n junction diode is formed by placing p and n type semiconductor materials in
intimate contact on an atomic scale. This may be achieved by diffusing acceptor
impurities in to an n type silicon crystal or by the opposite sequence.
In an open circuit p-n junction diode, majority carriers from either side will defuse
across the junction to the opposite side where they are in minority. These diffusing
carriers will leave behind a region of ionized atoms at the immediate vicinity of the
metallurgical junction. This region of immobile ionized atoms is called the space charge
region. This process continues till the resultant electric field (created by the space
charge density) and the potential barrier at the junction builds up to sufficient level to
prevent any further migration of carriers. At this point the p-n junction is said to be in
thermal equilibrium condition. Variation of the space charge density, the electric field
and the potential along the device is shown in Fig (a).
Electronics
Space change density the electric field and the electric potential
inside a p-n junction under (a) thermal equilibrium condition, (b)
reverse biased condition, (c) forward biased condition.
When an external voltage is applied with p side move negative then the n side
the junction is said to be under reverse bias condition. This reverse bias adds to the
height of the potential barrier. The electric field strength at the junction and the width
of the space change region (also called the depletion region because of the absence
of free carriers) also increases. On the other hand, free minority carrier densities (n-p in
the p side and pn in the n side) will be zero at the edge of the depletion region on
either side (Fig(b)). This gradient in minority carrier density causes a small flux of
minority carriers to defuse towards the deletion layer where they are swept
immediately by the large electric field into the electrical neutral region of the opposite
side. This will constitute a small leakage current across the junction from the n side to
the p side. There will also be a contribution to the leakage current by the electron hole
pairs generated in the space change layer by the thermal ionization process. These two
components of current together is called the reverse saturation current Is of the
diode. Value of Is is independent of the reverse voltage magnitude (up to a certain
level) but extremely sensitive to temperature variation. When the applied reverse
voltage exceeds some threshold value (for a given diode) the reverse current increases
rapidly. The diode is said to have undergone reverse break down. Reverse break down
is caused by "impact ionization" as explained below. Electrons accelerated by the large
depletion layer electric field due to the applied reverse voltage may attain sufficient
knick energy to liberate another electron from the covalent bonds when it strikes a
silicon atom. The liberated electron in turn may repeat the process. This cascading
effect (avalanche) may produce a large number of free electrons very quickly resulting
in a large reverse current. The power dissipated in the device increases manifold and
may cause its destruction. Therefore, operation of a diode in the reverse breakdown
region must be avoided.
When the diode is forward biased (i.e., p side more positive than n side) the
potential barrier is lowered and a very large number of minority carriers are injected to
6
Electronics
both sides of the junction. The injected minority a carrier eventually recombines with
the majority carries as they defuse further into the electrically neutral drift region. The
excess free carrier density in both p and n side follows exponential decay
characteristics. The characteristic decay length is called the "minority carrier diffusion
length" Carrier density gradients on either side of the junction are supported by a
forward current IF (flowing from p side to n side) which can be expressed as
IF = IS(exp (qv/kT )-1
(1.1)
Where, Is = Reverse saturation current ( Amps)
v = Applied forward voltage across the device (volts)
q = Change of an electron
k = Boltzmans constant
T = Temperature in Kelvin
Volt-Ampere ( i-v ) characteristics of a p-n junction diode

From the foregoing discussion the i-v characteristics of a p-n junction diode can be
drawn as shown in Fig. While drawing this characteristic the ohmic drop in the bulk
of the semiconductor body has been neglected.
Topic
Power Semiconductor- Thyristors
Sub Topics
Structure, Ton-Toff , V-I Characteristics of Thyristors
2.(b).POWER SEMICONDUCTOR-THYRISTORS
Although the large semiconductor diode was a predecessor to thyristors, the
modern power electronics area truly began with advent of thyristors. One of the first
developments was the publication of the P-N-P-N transistor switch concept in 1956 by
J.L. Moll and others at Bell Laboratories, probably for use in Bells Signal application.
However, engineers at General Electric quickly recognized its significance to power
conversion and control and within nine months announced the first commercial Silicon
Controlled Rectifier in 1957. This had a continuous current carrying capacity of 25A and
a blocking voltage of 300V. Thyristors (also known as the Silicon Controlled Rectifiers or
SCRs) have come a long way from this modest beginning and now high power light
triggered thyristors with blocking voltage in excess of 6kv and continuous current
rating in excess of 4kA are available. They have reigned supreme for two entire
decades in the history of power electronics. Along the way a large number of other
7
Electronics
devices with broad similarity with the basic thyristor (invented originally as a phase
control type device) have been developed. They include, inverter grade fast thyristor,
Silicon Controlled Switch (SCS), light activated SCR (LASCR), Asymmetrical Thyristor
(ASCR) Reverse Conducting Thyristor (RCT), Diac, Triac and the Gate turn off thyristor
(GTO).
From the construction and operational point of view a thyristor is a four layer,
three terminal, minority carrier semi-controlled device. It can be turned on by a current
signal but can not be turned off without interrupting the main current. It can block
voltage in both directions but can conduct current only in one direction. During
conduction it offers very low forward voltage drop due to an internal latch-up
mechanism. Thyristors have longer switching times (measured in tens of s) compared
to a BJT. This, coupled with the fact that a thyristor can not be turned off using a control
input, has all but eliminated thyristors in high frequency switching applications
involving a DC input (i.e., choppers, inverters). However in power frequency ac
applications where the current naturally goes through zero, thyristor remain popular
due to its low conduction loss its reverse voltage blocking capability and very low
control power requirement. In fact, in very high power (in excess of 50 MW) AC DC
(phase controlled converters) or AC AC (cyclo-converters) converters, thyristors still
remain the device of choice.
2.(b).1.Constructional Features of a Thyristor
Fig. Shows the circuit symbol, schematic construction and the photograph of a typical
thyristor.
Constructional features of a thyristor

(a) Circuit Symbol (b) Schematic Construction (c) Photograph
As shown in Fig.(b) the primary crystal is of lightly doped n- type on either side of which
two p type layers with doping levels higher by two orders of magnitude are grown. As in
the case of power diodes and transistors depletion layer spreads mainly into the lightly
doped n- region. The thickness of this layer is therefore determined by the required
blocking voltage of the device. However, due to conductivity modulation by carriers
from the heavily doped p regions on both side during ON condition the ON state
voltage drop is less. The outer n+ layers are formed with doping levels higher then
both the p type layers. The top p layer acts as the Anode terminal while the bottom
n+ layers acts as the Cathode. The Gate terminal connections are made to the
bottom p layer.
As it will be shown later, that for better switching performance it is required to
maximize the peripheral contact area of the gate and the cathode regions. Therefore,
the cathode regions are finely distributed between gate contacts of the p type layer. An
Involute structure for both the gate and the cathode regions is a preferred design
structure.
Basic operating principle of a thyristor
8
Electronics
The underlying operating principle of a thyristor is best understood in terms of the

two transistor analogy as explained below.
Two transistor analogy of a thyristor construction.

(a) Schematic Construction, (b) Schematic division in component transistor
(c) Equivalent circuit in terms of two transistors.
Let us consider the behavior of this p n p n device with forward voltage applied,
i.e anode positive with respect to the cathode and the gate terminal open. With this
voltage polarity J1 & J3 are forward biased while J2 reverse biased.
Under this condition.
ic1=1IA+Ico1
(1.2)
ic2=2Ik+Ico2
(1.3)
Where 1 & 2 are current gains of Q1 & Q2 respectively while Ico1 & Ico2 are reverse
saturation currents of the CB junctions of Q1 & Q2 respectively.
Now from Fig 1.6 (c).
ic1 +ic2 =IA
(1.4)
& IA=Ik ( IG=0)
(1.5)
Combining Eq 1.2 & 1.5
(1.6)
Where Ico Ico1 +Ico2 is the total reverse leakage current of J2
Now as long as VAK is small Ico is very low and both 1 & 2 are much lower than
unity. Therefore, total anode current IA is only slightly greater than Ico. However, as VAK
is increased up to the avalanche break down voltage of J2, Ico starts increasing rapidly
due to avalanche multiplication process. As Ico increases both 1 & 2 increase and 1
+ 2 approaches unity. Under this condition large anode current starts flowing,
restricted only by the external load resistance. However, voltage drop in the external
resistance causes a collapse of voltage across the thyristor. The CB junctions of both Q1
& Q2 become forward biased and the total voltage drop across the device settles down
to approximately equivalent to a diode drop. The thyristor is said to be in ON state.
9
Electronics
Just after turn ON if Ia is larger than a specified current called the Latching
Current IL, 1 and 2 remain high enough to keep the thyristor in ON state. The only
way the thyristor can be turned OFF is by bringing IA below a specified current called
the holding current (IH) where upon 1 & 2 starts reducing. The thyristor can regain
forward blocking capacity once excess stored charge at J2 is removed by application of
a reverse voltage across A & K (ie, K positive with respect A).
It is possible to turn ON a thyristor by application of a positive gate current
(flowing from gate to cathode) without increasing the forward voltage across the device
up to the forward break-over level. With a positive gate current equation 1.5 can be
written as
IK=IA+IG
(1.7)
Combining with Eqns. 1.2 to 1.4
(1.8)
Obviously with sufficiently large IG the thyristor can be turned on for any value of
Ico (and hence VAK). This is called gate assisted turn on of a Thyristor. This is the usual
method by which a thyristor is turned ON.
When a reverse voltage is applied across thyristor (i.e, cathode positive with
respect to anode.) junctions J1 and J3 are reverse biased while J2 is forward biased. Of
these, the junction J3 has a very low reverse break down voltage since both the n+ and
p regions on either side of this junction are heavily doped. Therefore, the applied
reverse voltage is almost entirely supported by junction J1. The maximum value of the
reverse voltage is restricted by
a) The maximum field strength at junction J1 (avalanche break down)
b) Punch through of the lightly doped n- layer.
Since the p layers on either side of the n- region have almost equal doping levels
the avalanche break down voltage of J1 & J2 are almost same. Therefore, the forward
and the reverse break down voltage of a thyristor are almost equal. Up to the break
down voltage of J1 the reverse current of the thyristor remains practically constant and
increases sharply after this voltage. Thus, the reverse characteristics of a thyristor are
similar to that of a single diode.
If a positive gate current is applied during reverse bias condition, the junction J 3
becomes forward biased. In fact, the transistors Q1 & Q2 now work in the reverse
direction with the roles of their respective emitters and collectors interchanged.
However, the reverse 1 & 2 being significantly smaller than their forward counterparts
latching of the thyristor does not occur. However, reverse leakage current of the
thyristor increases considerably increasing the OFF state power loss of the device.
If a forward voltage is suddenly applied across a reverse biased thyristor, there
will be considerable redistribution of charges across all three junctions. The resulting
current can become large enough to satisfy the condition 1 + 2 = 1 and consequently
turn on the thyristor. This is called dv/dt turn on of a thyristor and should be avoided.
2.(b).2.Switching Characteristics of a Thyristor
During Turn on and Turn off process a thyristor is subjected to different voltages
across it and different currents through it. The time variations of the voltage across a
10
Electronics
thyristor and the current through it during Turn on and Turn off constitute the switching
characteristics of a thyristor.
Turn on Switching Characteristics
A forward biased thyristor is turned on by applying a positive gate voltage
between the gate and cathode as shown in Fig.
Turn on characteristics of a thyristor.

Fig. shows the waveforms of the gate current (ig), anode current (iA) and anode
cathode voltage (VAK) in an expanded time scale during Turn on. The reference circuit
and the associated waveforms are shown in the inset. The total switching period being
much smaller compared to the cycle time, iA and VAK before and after switching will
appear flat.
As shown in Fig. there is a transition time tON from forward off state to forward
on state. This transition time is called the thyristor turn of time and can be divided into
three separate intervals namely, (i) delay time (td) (ii) rise time (tr) and (iii) spread time
(tp). These times are shown in Fig. for a resistive load.
Delay time (td): After switching on the gate current the thyristor will start to conduct
over the portion of the cathode which is closest to the gate. This conducting area starts
spreading at a finite speed until the entire cathode region becomes conductive. Time
taken by this process constitute the turn on delay time of a thyristor. It is measured
from the instant of application of the gate current to the instant when the anode
current rises to 10% of its final value (or VAK falls to 90% of its initial value). Typical
value of td is a few micro seconds.
Rise time (tr): For a resistive load, rise time is the time taken by the anode current
to rise from 10% of its final value to 90% of its final value. At the same time the voltage
VAK falls from 90% of its initial value to 10% of its initial value. However, current rise
and voltage fall characteristics are strongly influenced by the type of the load. For
inductive load the voltage falls faster than the current. While for a capacitive load VAK
falls rapidly in the beginning. However, as the current increases, rate of change of
anode voltage substantially decreases.
If the anode current rises too fast it tends to remain confined in a small area. This can
give rise to local hot spots and damage the device. Therefore, it is necessary to limit
the rate of rise of the ON state current (dia/dt) by using an inductor in series with the
device. Usual values of maximum allowable dia/dt is in the range of 20-200 A/s.
11
Electronics
Spread time (tp): It is the time taken by the anode current to rise from 90% of its
final value to 100%. During this time conduction spreads over the entire cross section
of the cathode of the thyristor. The spreading interval depends on the area of the
cathode and on the gate structure of the thyristor.
Turn off Switching Characteristics
Once the thyristor is on, and its anode current is above the latching current level
the gate loses control. It can be turned off only by reducing the anode current below
holding current. The turn off time tq of a thyristor is defined as the time between the
instant anodes current becomes zero and the instant the thyristor regains forward
blocking capability. If forward voltage is applied across the device during this period the
thyristor turns on again. During turn off time, excess minority carriers from all the four
layers of the thyristor must be removed. Accordingly tq is divided in to two intervals,
the reverse recovery time (trr) and the gate recovery time (tqr). Fig. Shows the variation
of anode current and anode cathode voltage with time during turn off operation on an
expanded scale.
Turn off characteristics of a thyristor

The anode current becomes zero at time t1 and starts growing in the negative
direction with the same diA/dt till time t2. This negative current removes excess carriers
from junctions J1 & J3. At time t2 excess carriers densities at these junctions are not
sufficient to maintain the reverse current and the anode current starts decreasing. The
value of the anode current at time t2 is called the reverse recovery current (Irr). The
reverse anode current reduces to the level of reverse saturation current by t3. Total
charge removed from the junctions between t1 & t3 is called the reverse recovery
charge (Qrr). Fast decaying reverse current during the interval t2 t3 coupled with the
di/dt limiting inductor may cause a large reverse voltage spike (Vrr) to appear across
the device. This voltage must be limited below the VRRM rating of the device. Up to time
t2 the voltage across the device (VAK) does not change substantially from its on state
value. However, after the reverse recovery time, the thyristor regains reverse blocking
capacity and VAK starts following supply voltage vi. At the end of the reverse recovery
period (trr) trapped charges still exist at the junction J2 which prevents the device from
blocking forward voltage just after trr. These trapped charges are removed only by the
process of recombination. The time taken for this recombination process to complete
(between t3 & t4) is called the gate recovery time (tgr). The time interval tq = trr + tgr is
called device turn off time of the thyristor.
No forward voltage should appear across the device before the time tq to avoid
its inadvertent turn on. A circuit designer must provide a time interval tc (tc > tq) during
which a reverse voltage is applied across the device. tc is called the circuit turn off
12
Electronics
time.
The reverse recovery charge Qrr is a function of the peak forward current before
turn off and its rate of decrease diA/dt. Manufacturers usually provide plots of Qrr as a
function of diA/dt for different values of peak forward current. They also provide the
value of the reverse recovery current Irr for a given IA and diA/dt. Alternatively Irr can be
evaluated from the given Qrr characteristics following similar relationships as in the
case of a diode.
As in the case of a diode the relative magnitudes of the time intervals t1 t2 and t2 t3
depends on the construction of the thyristor. In normal recovery converter grade
thyristor they are almost equal for a specified forward current and reverse recovery
current. However, in a fast recovery inverter grade thyristor the interval t2 t3 is
negligible compared to the interval t1 t2. This helps reduce the total turn off time tq of
the thyristor (and hence allow them to operate at higher switching frequency).
However, large voltage spike due to this snappy recovery will appear across the
device after the device turns off. Typical turn off times of converter and inverter grade
thyristors is in the range of 50-100 s and 5-50 s respectively. As has been
mentioned in the introduction thyristor is the device of choice at the very highest
power levels. At these power levels (several hundreds of megawatts) reliability of the
thyristor power converter is of prime importance. Therefore, suitable protection
arrangement must be made against possible overvoltage, over current and unintended
turn on for each thyristor. At the highest power level (HVDC transmission system)
thyristor converters operate from network voltage levels in excess of several hundreds
of kilo volts and conduct several tens of kilo amps of current. They usually employ a
large number of thyristors connected in series parallel combination. For maximum
utilization of the device capacity it is important that each device in this series parallel
combination share the blocking voltage and on state current equally. Special equalizing
circuits are used for this purpose.
2.(b).3.Static output i-v characteristics of a thyristor
Static output characteristics of a Thyristor

The circuit symbol in the left hand side inset defines the polarity conventions of
the variables used in this figure. With ig = 0, VAK has to increase up to forward break
over voltage VBRF before significant anode current starts flowing. However, at VBRF
forward break over takes place and the voltage across the thyristor drops to VH (holding
voltage). Beyond this point voltage across the thyristor (VAK) remains almost constant at
VH (1-1.5v) while the anode current is determined by the external load.
13
Electronics
The magnitude of gate current has a very strong effect on the value of the break
over voltage as shown in the figure. The right hand side figure in the inset shows a
typical plot of the forward break over voltage (VBRF) as a function of the gate current (Ig)
After Turn ON the thyristor is no more affected by the gate current. Hence, any
current pulse (of required magnitude) which is longer than the minimum needed for
Turn ON is sufficient to effect control. The minimum gate pulse width is decided by
the external circuit and should be long enough to allow the anode current to rise above
the latching current (IL) level. The left hand side of Fig 1.7 shows the reverse i-v
characteristics of the thyristor. Once the thyristor is ON the only way to turn it OFF is by
bringing the thyristor current below holding current (IH). The gate terminal has no
control over the turn OFF process. In ac circuits with resistive load this happens
automatically during negative zero crossing of the supply voltage. This is called
natural commutation or line commutation. However, in dc circuits some
arrangement has to be made to ensure this condition. This process is called forced
commutation.
During reverse blocking if ig = 0 then only reverse saturation current (Is) flows
until the reverse voltage reaches reverse break down voltage (VBRR). At this point
current starts rising sharply. Large reverse voltage and current generates excessive
heat and destroys the device. If ig > 0 during reverses bias condition the reverse
saturation current rises as explained in the previous section. This can be avoided by
removing the gate current while the thyristor is reverse biased.
Part-A Question
1. What is the difference between power diode and signal diode?
2. What is the turn-off time for converter grade SCRs and inverter grade
SCRs?
3. Define circuit turn off time.
4. Define latching current.
5. Define holding current.
Part-B Question
1. Explain the operation of SCR using two transistor analogy.
2. Briefly discuss the V-I characteristics of SCR.
3. Draw and explain the switching characteristics of SCR.
4. Explain the basic structure and V-I characteristics of power diodes with
neat diagram.
Topic
Power Semiconductor- Triac
Sub Topics
Structure, Ton-Toff , V-I Characteristics of Triac
3. POWER SEMICONDUCTOR- Triac

The Triac is a member of the thyristor family. But unlike a thyristor which
conducts only in one direction (from anode to cathode) a triac can conduct in both
directions. Thus a triac is similar to two back to back (anti parallel) connected thyristosr
but with only three terminals. As in the case of a thyristor, the conduction of a triac is
initiated by injecting a current pulse into the gate terminal. The gate looses control
over conduction once the triac is turned on. The triac turns off only when the current
through the main terminals become zero. Therefore, a triac can be categorized as a
minority carrier, a bidirectional semi-controlled device. They are extensively used in
14
Electronics
residential lamp dimmers, heater control and for speed control of small single phase
series and induction motors.
3.1 Construction and operating principle
Fig. (a) and (b) show the circuit symbol and schematic cross section of a triac
respective. As the Triac can conduct in both the directions the terms anode and
cathode are not used for Triacs. The three terminals are marked as MT1 (Main Terminal
1), MT2 (Main Terminal 2) and the gate by G. As shown in Fig.(b) the gate terminal is
near MT1 and is connected to both N3 and P2 regions by metallic contact. Similarly MT1
is connected to N2 and P2 regions while MT2 is connected to N4 and P1 regions.
Circuit symbol and schematic construction of a Triac

(a) Circuit symbol (b) Schematic construction.
Since a Triac is a bidirectional device and can have its terminals at various
combinations of positive and negative voltages, there are four possible electrode
potential combinations as given below
1. MT positive with respect to MT , G positive with respect to MT
2
1
1
2. MT positive with respect to MT , G negative with respect to MT
2
1
1
3. MT negative with respect to MT , G negative with respect to MT
2
1
1
4. MT negative with respect to MT , G positive with respect to MT
2
1
1
The triggering sensitivity is highest with the combinations 1 and 3 and are generally
used. However, for bidirectional control and uniforms gate trigger mode sometimes
trigger modes 2 and 3 are used. Trigger mode 4 is usually averred. Fig (a) and (b)
explain the conduction mechanism of a triac in trigger modes 1 & 3 respectively.
Conduction mechanism of a triac in trigger modes 1 and 3

(a)
Mode 1(b) Mode 3 .
In trigger mode-1 the gate current flows mainly through the P2 N2 junction like an
ordinary thyristor. When the gate current has injected sufficient charge into P2 layer the
triac starts conducting through the P1 N1 P2 N2 layers like an ordinary thyristor. In the
15
Electronics
trigger mode-3 the gate current Ig forward biases the P2 P3 junction and a large number
of electrons are introduced in the P2 region by N3. Finally the structure P2 N1 P1 N4 turns
on completely.
3.2 Steady State Output Characteristics and Ratings of a Triac
Steady state V I characteristics of a Triac

From a functional point of view a triac is similar to two thyristors connected in anti
parallel. Therefore, it is expected that the V-I characteristics of Triac in the 1st and 3rd
quadrant of the V-I plane will be similar to the forward characteristics of a thyristors. As
shown in Fig., with no signal to the gate the triac will block both half cycle of the
applied ac voltage provided its peak value is lower than the break over voltage (VBO) of
the device. However, the turning on of the triac can be controlled by applying the gate
trigger pulse at the desired instance. Mode-1 triggering is used in the first quadrant
where as Mode-3 triggering is used in the third quadrant. As such, most of the thyristor
characteristics apply to the triac (ie, latching and holding current). However, in a triac
the two conducting paths (from MT1 to MT2 or from MT1 to MT1) interact with each other
in the structure of the triac. Therefore, the voltage, current and frequency ratings of
triacs are considerably lower than thyristors. At present triacs with voltage and current
ratings of 1200V and 300A (rms) are available. Triacs also have a larger on state
voltage drop compared to a thyristor. Manufacturers usually specify characteristics
curves relating rms device current and maximum allowable case temperature as shown
in Fig . Curves relating the device dissipation and RMS on state current are also
provided for different conduction angles.
RMS ON state current Vs maximum case temperature.
16
Electronics
Part-A Question
1. Distinguish between SCR and TRIAC.
2. What are the applications of TRAIC?
Part-B Question
1. Explain the construction and V-I characteristics of TRIAC with neat diagram.
Topic
Power Semiconductor- GTO
Sub Topics
Structure, Ton-Toff , V-I Characteristics of GTO
4.(a) POWER SEMICONDUCTOR- Gate Turn Off Thyristor (GTO)

4.(a).1Constructional Features of a GTO
Fig shows the circuit symbol and two different schematic cross section of a GTO.
Circuit symbol and schematic cross section of a GTO (a) Circuit Symbol,
(b) Anode shorted GTO structure, (c) Buffer layer GTO structure.
Like a thyristor, a GTO is also a four layer three junction p-n-p-n device. In order
to obtain high emitter efficiency at the cathode end, the n+ cathode layer is highly
doped. Consequently, the break down voltage of the function J3 is low (typically 2040V). The p type gate region has conflicting doping requirement. To maintain good
emitter efficiency the doping level of this layer should be low, on the other hand, from
the point of view of good turn off properties, resistively of this layer should be as low as
possible requiring the doping level of this region to be high. Therefore, the doping level
of this layer is highly graded. Additionally, in order to optimize current turn off
capability, the gate cathode junction must be highly interdigitated. A 3000 Amp GTO
may be composed of up to 3000 individual cathode segments which are a accessed via
a common contact. The most popular design features multiple segments arranged in
concentric rings around the device center.
The maximum forward blocking voltage of the device is determined by the
doping level and the thickness of the n type base region next. In order to block several
kv of forward voltage the doping level of this layer is kept relatively low while its
thickness is made considerably higher (a few hundred microns). Beyond the maximum
allowable forward voltage either the electric field at the main junction (J2) exceeds a
critical value (avalanche break down) or the n base fully depletes, allowing its electric
field to touch the anode emitter (punch through).
17
Electronics
The junction between the n base and p+ anode (J1) is called the anode junction.
For good turn on properties the efficiency of this anode junction should be as high as
possible requiring a heavily doped p+ anode region. However, turn off capability of
such a GTO will be poor with very low maximum turn off current and high losses. There
are two basic approaches to solve this problem.
In the first method, heavily doped n+ layers are introduced into the p+ anode
layer. They make contact with the same anode metallic contact. Therefore, electrons
traveling through the base can directly reach the anode metal contact without causing
hole injection from the p+ anode. This is the classic anode shorted GTO structure as
shown in Fig (b). Due to presence of these anode shorts the reverse voltage blocking
capacity of GTO reduces to the reverse break down voltage of junction J 3 (20-40 volts
maximum). In addition a large number of anode shorts reduces the efficiency of the
anode junction and degrades the turn on performance of the device. Therefore, the
densities of the anode shorts are to be chosen by a careful compromise between the
turn on and turn off performance.
In the other method, a moderately doped n type buffer layer is juxtaposed
between the n- type base and the anode. As in the case of a power diode and BJT this
relatively high density buffer layer changes the shape of the electric field pattern in the
n- base region from triangular to trapezoidal and in the process, helps to reduce its
width drastically. However, this buffer layer in a conventional anode shorted GTO
structure would have increased the efficiency of the anode shorts. Therefore, in the
new structure the anode shorts are altogether dispensed with and a thin p+ type layer
is introduce as the anode. The design of this layer is such that electrons have a high
probability of crossing this layer without stimulating hole injection. This is called the
Transparent emitter structure and is shown in Fig (c).
4. (a).2.Switching Characteristics of a GTO
Switching characteristics of a GTO.

Fig. shows the switching characteristics of a GTO and refers to the resistive dc
load switching circuit shown on the right hand side. When the GTO is off the anode
current is zero and VAK = Vd. To turn on the GTO, a positive gate current pulse is injected
through the gate terminal. A substantial gate current ensures that all GTO cathode
segments are turned on simultaneously and within a short time. There is a delay
between the application of the gate pulse and the fall of anode voltage, called the turn
on delay time td. After this time the anode voltage starts falling while the anode current
18
Electronics
starts rising towards its steady value IL. Within a further time interval tr they reach 10%
of their initial value and 90% of their final value respectively. tr is called the current rise
time (voltage fall time). Both td and maximum permissible on state diA/dt are very
much gate current dependent. High value of IgM and dig/dt at turn on reduces these
times and increases maximum permissible on state diA/dt . It should be noted that large
value of ig (IgM) and dig/dt are required during td and tr only. After this time period both
vg and ig settles down to their steady value. A minimum ON time period t ON (min) is
required for homogeneous anode current conduction in the GTO. This time is also
necessary for the GTO to be able to turn off its rated anode current.
To turn off a GTO the gate terminal is negatively biased with respect to the
cathode. With the application of the negative bias the gate current starts growing in the
negative direction. However, the anode voltage, current or the gate voltage does not
change appreciably from there on state levels for a further time period called the
storage time (ts). The storage time increases with the turn off anode current and
decrease with digQ/dt. During storage time the load current at the cathode end is
gradually diverted to the gate terminal. At the end of the storage time gate current
reaches its negative maximum value IgQ. At this point both the junctions J2 & J3 of the
GTO starts blocking voltage. Consequently, both the gate cathode and the anode
cathode voltage starts rising towards their final value while the anode current starts
decreasing towards zero. At the end of current fall time tf the anode current reaches
10% of its initial value after which both the anode current and the gate current
continues to flow in the form of a current tail for a further duration of ttail. A GTO is
normally used with a R-C turn off snubber. Therefore, VAK does not start to rise
appreciably till tf. At this point VAK starts rising rapidly and exceeds the dc voltage Vd
(VdM) (due to resonance of snubber capacitor with didt limiting inductor) before setting
down at its steady value Vd . A GTO should not be retriggered within a minimum off
period off (min) to avoid the risk of failure due to localized turn ON. GTOs have typically
low turn off gain in the range of 4-5.
4. (a).3.Steady state and dynamic characteristics of a GTO
Steady state characteristics of a GTO

(a) Output characteristics ;(b) Gate characteristics.
This characteristic in the first quadrant is very similar to that of a thyristor as
shown in Fig.(a). However, the latching current of a GTO is considerably higher than a
thyristor of similar rating. The forward leakage current is also considerably higher. In
fact, if the gate current is not sufficient to turn on a GTO it operates as a high voltage
low gain transistor with considerable anode current. It should be noted that a GTO can
19
Electronics
block rated forward voltage only when the gate is negatively biased with respect to the
cathode during forward blocking state. At least, a low value resistance must be
connected across the gate cathode terminal. Increasing the value of this resistance
reduces the forward blocking voltage of the GTO. Asymmetric GTOs have small (20-30
V) reverse break down voltage. This may lead the device to operate in reverse
avalanche under certain conditions. This condition is not dangerous for the GTO
provided the avalanche time and current are small. The gate voltage during this period
must remain negative.
Fig.(b) shows the gate characteristics of a GTO. The zone between the min and
max curves reflects parameter variation between individual GTOs. These
characteristics are valid for DC and low frequency AC gate currents. They do not give
correct voltage when the GTO is turned on with high dia/dt and dIG/dt. VG in this case is
much higher.
Topic
Sub Topics
Power Semiconductor- Power Bipolar Junction Transistor (BJT)

Structure, Ton-Toff , V-I Characteristics of BJT
4.(b) POWER SEMICONDUCTOR- Power Bipolar Junction Transistor (BJT)

4.(b).1Constructional Features of a Power BJT
Power transistors face the same conflicting design requirements (i.e. large off
state blocking voltage and large on state current density) as that of a power diode.
Therefore, it is only natural to extend some of the constructional features of power
diodes to power BJT. Following Section summarizes some of the constructional features
of a Power BJT. Since Power Transistors are predominantly of the n-p-n type, in this
section and subsequently only this type of transistor will be discussed.
A power BJT has vertically oriented alternating layers of n type and p type
semiconductor materials as shown in Fig 1.17(a). The vertical structure is preferred
for power transistors because it maximizes the cross sectional area through which
the on state current flows. Thus, on state resistance and power lass is minimized.
In order to maintain a large current gain (and hence reduce base drive current)
the emitter doping density is made several orders of magnitude higher than the base
region. The thickness of the base region is also made as small as possible.
In order to block large voltage during OFF state a lightly doped collector drift
region is introduced between the moderately doped base region and the heavily
doped collector region. The function of this drift region is similar to that in a Power
Diode. However, the doping density donation of the base region being moderate
the depletion region does penetrate considerably into the base. Therefore, the width
of the base region in a power transistor cannot be made as small as that in a signal
level transistor. This comparatively larger base width has adverse effect on the
current gain () of a Power transistor which typically varies within 5-20. As will be
discusses later the collector drift region has significant effect on the output
characteristics of a Power BJT.
Practical Power transistors have their emitters and bases interleaved as narrow
fingers. This is necessary to prevent current crowding and consequent second
break down. In addition multiple emitter structure also reduces parasitic ohmic
20
Electronics
resistance in the base current path. These constructional features of a Power BJT are
shown schematically in
Fig.(a). Fig.(b) shows the photograph of some community available Power transistors
in different packages.
Constructional Features of a Power Bipolar Junction Transistor

(a) Schematic of Construction,
(b) Photograph of commercial packages.
4.(b).2 Switching characteristics of a Power Transistor
Turn On characteristics of a Power Transistor
From the description of the basic operating principle of a power transistor presented
in the previous sections it is clear that minority carriers must be moved across different
regions of a power transistor in order to make it switch between cut off and saturation
regions of operation. The time delay in the switching operation of a power transistor is
due to the time taken by the minority carriers to reach appropriate density levels in
different regions. The exact level of minority carrier densities (and depletion region
widths) required for proper switching is determined by the collector current and biasing
collector voltage during switching, both of which are determined by external circuits.
The rate at which these densities are attained is determined by the base current
waveform. Therefore, the switching characteristics of a power transistor are always
specified in relation to the external load circuit and the base current waveform as
shown in Fig. Which shows a clamped inductive switching circuit with a flat base drive.
21
Electronics
Turn ON characteristics of a power transistor; (a) Switching circuit, (b)

Switching wave forms
The switching wave forms shown in Fig.(b) are the expanded and to some extent
idealized version of the actual waveforms that will be observed in a clamped
inductive switching circuit as shown in Fig. (a). Some simplifying assumptions have
been made to draw these waveforms. These are
The load inductor has been assumed to be large enough so that the load current
does
not change during Turn ON period.
Reverse recovery characteristics of D has been ignored.
All parasitic elements have been ignored.
Before t = 0, the transistor (Q) was in the OFF state. In order to utilize the
increased break down voltage (VCBO) the base-emitter junction of a Power Transistor is
usually reverse biased during OFF state. Under this condition only negligible leakage
current flows through the transistor. Power loss due to this leakage current is negligible
compared to other components of power loss in a transistor. Therefore, it is not shown
in Fig (b). The entire load current flows through the diode and VCE is clamped to VCC
(approximately). To turn the transistor ON at t = 0, the base biasing voltage VBB
changes to a suitable positive value. This starts the process of charge redistribution at
the base-emitter junction. The process is akin to charging of a capacitor. Indeed, the
reverse biased base emitter junction is often represented by a voltage dependent
capacitor, the value of which is given by the manufacturer as a function of the baseemitter reverse bias voltage. The rising base current that flows during this period can
be thought of as this capacitor charging current. Finally at t = td the BE junction is
forward biased. The junction voltage and the base current settles down to their steady
state values. During this period, called the Turn ON delay time no appreciable
collector current flows. The values of iO and VCE remains essentially at their OFF state
levels.
At the end of the delay time (td ON) the minority carrier density at the base region
quickly approaches its steady state distribution and the collector current starts rising
while the diode current (id) starts falling. At t = tdON + tri the collector current becomes
22
Electronics
equal to the load current (and id becomes zero) IL. At this point D starts blocking reverse
voltage and VCE becomes unclamped. tri is called the current rise time of the transistor.
At the end of the current rise time the diode D regains reverse blocking capacity.
The collector voltage VCE which has so far been clamped to VCC because of the
conducting diode D starts falling towards its saturation voltage VCE (sat). The initial
fall of VCE is rapid. During this period the switching trajectory traverses through the
active region of the output characteristics of the transistor. At the end of this rapid fall
(tfv1) the transistor enters quasi saturation region. The fall of VCE in the quasi
saturation region is considerably slower. At the end of this slow fall (tfv2) the transistor
enters hard saturation region and the collector voltage settles down to the saturation
voltage level VCE (sat) corresponding to the load current IL. Turn ON process ends here.
The total turn on time is thus, TSW (ON) = td (ON) + tri + tfv1 +tfv2.
Power loss occurs at all time during the operation of a power transistor. However,
the collector leakage current is usually negligibly small and power loss due it can be
safely neglected in comparison to the power loss during ON condition. Power loss
occurs during Turning ON a Power transistor due to simultaneous existence of non-zero
VCE and ic during tri, tfv1, and tfv2. The energy lost during these periods is called the Turn
ON loss and given by the area under the Pl curve in Fig (b). The average Turn ON loss is
obtained by dividing this area by (tri + tfv1 + tfv2). For safe Turn ON this average power
loss must be less than the limit set on the maximum power dissipation in the FBSOA
corresponding to a pulse width greater than tri + tfv1 + tfv2. Similar restriction with
respect to second break down should also be observed.
Turn ON time can be reduced by increasing the base current. However large base
current increases the quantity of excess carrier in the base and collector drift region
which has to be removed during Turn Off. As will be seen later this increases the Turn
OFF time. The Turn ON delay time can however be reduced by boosting the base
current at the beginning of the Turn ON process. This can be achieved by connecting a
small capacitance across RB. This increases the rate of rise of VBE & iB. Therefore, Turn
ON delay time decreases. However, in steady state iB settle downs to a value
determined by RB & VBB and no adverse effect on the Turn OFF time is observed.
In figure (b) the reverse recovery current of D has been neglected. If this current is
not negligible then for safe Turn ON operation the sum of the load current and the diode
reverse recovery current must be less than the ICM rating of the transistor. Thermal and
second break down limits must also be observed.
It should be noted that there is some power loss at the BE junction as well. This
power loss depends on the current gain of the transistor during hard saturation. Since
current gain reduces during saturation (typically between 5 to 10) this power loss may
become significant. Manufacturers usually provide the values of td (ON), tri, tfv as
functions of ic for a given base current and case temperature.
Turn Off Characteristics of a Power Transistor
During Turn OFF a power transistor makes transition from saturation to cut off
region of operation. Just as in the case of Turn ON, substantial redistribution of minority
charge carriers is involved in the Turn OFF process. Idealized waveforms of several
important variables in the clamped inductive switching circuit of Fig. (a) during the Turn
OFF process of Q are shown in Fig (a)
23
Electronics
Turn off characteristics of a BJT.

(a) Switching wave forms
(b) Switching
trajectory
The Turn OFF process starts with the base drive voltage going negative to a value
-VBB. The base-emitter voltage however does not change from its forward bias value of
VBE(sat) immediately, due to the excess, minority carriers stored in the base region. A
negative base current starts removing this excess carrier at a rate determined by the
negative base drive voltage and the base drive resistance. After a time ts called the
storage time of the transistor, the remaining stored charge in the base becomes
insufficient to support the transistor in the hard saturation region. At this point the
transistor enters quasi saturation region and the collector voltage starts rising with a
small slope. After a further time interval trv1 the transistor completes traversing
through the quasi saturation region and enters the active region. The stored charge in
the base region at this point is insufficient to support the full negative base current. VBE
starts falling forward VBB and the negative base current starts reducing. In the active
region, VCE increases rapidly towards VCC and at the end of the time interval trv2
exceeds it to turn on D. VCE remains clamped at VCC, thereafter by the conducting diode
D. At the end of trv2 the stored base charge can no longer support the full load current
through the collector and the collector current starts falling. At the end of the current
fall time tfi the collector current becomes zero and the load current freewheels through
the diode D. Turn OFF process of the transistor ends at this point. The total Turn OFF
time is given by Ts (OFF) = ts + trv1 + trv2 + tfi
As in the case of Turn ON considerable power loss takes place during Turn OFF due to
simultaneous existence of ic and VCE in the intervals trv1, trv2 and tfi. The last trace of Fig
(a) shows the instantaneous power loss profile during these intervals. The total energy
last per turn off operation is given by the area under this curve. For safe turn off the
average power dissipation during trv1 + trv2 + tfi should be less than the power
dissipation limit set by the FBSOA corresponding to a pulse width greater than trv1 + trv2
+ tfi. Turn OFF time intervals of a power transistor are strongly influenced by the
operating conditions and the base drive design. Manufacturers usually specify these
values as functions of collector current for given positive and negative base current and
24
Electronics
case temperatures. Variations of these time intervals as function of the ratio of positive
to negative base currents for different collector currents are also specified.
In this section and the precious one inductive load switching has been considered.
However, if the load is resistive. The freewheeling diode D will not be used. In that case
the collector voltage (VCE) and collector current (ic) will fall and rise respectively
together during Turn ON and rise and fall respectively together during Turn OFF. Other
characteristics of the switching process will remain same. The switching Power loss in
this case will also be substantially lower.
4.(b).3 i-v characteristics of a Power Transistor

A typical output (iC Vs VCE) characteristics of an n-p-n type power transistor is shown
in Fig . A power transistor exhibits Cut off, Active and Saturation regions of
operation in its output characteristics similar to a signal level transistor. In fact output
characteristics of a Power Transistor in the Cut off and Active regions are
qualitatively identical to a signal level transistor. Certain quantitative restrictions apply,
however, which are discussed next.
Output ( ic VCE ) characteristics of an n p n type Power Transistor

In the cut off region (iB 0) the collector current is almost zero. The maximum
voltage between collector and emitter under this condition is termed Maximum
forward blocking voltage with base terminal open (iB = 0) and is denoted by VCEO. For
all practical purpose this is the maximum voltage that can be applied in the forward
direction (C positive with respect to E) across a power transistor since a power
transistor is expected to see any significant forward voltage only with iB = 0. This
blocking voltage can however be increased to a value VCBO by keeping the emitter
terminal open. In this case iB< 0. Actually VCBO is the breakdown voltage of the collector
base junction. However, since the open base configuration is more common the value
of VCEO is used by the manufacturers as the maximum voltage rating of power
transistor. Power transistors have poor reverse voltage withstanding capability due to
low break down voltage of the base-emitter junction. Therefore, reverse voltage (C
negative with respect to E) should not appear across a power transistor.
25
Electronics
In the active region the ratio of collector current to base current (DC current Gain
()) remains fairly constant up to certain value of the collector current after which it
falls off rapidly. Manufacturers usually provide a graph showing the variation of as a
function of the collector current for different junction temperatures and collector
emitter voltages. This graph is useful for designing the base drive of a Power transistor.
Typically, the value of the dc current gain of a Power transistor is much smaller
compared to their signal level counterpart.
The maximum collector-emitter voltage that a power transistor can withstand in
active region is determined by the Base collector avalanche break down voltage. This
voltage, denoted by VSUS in Fig, is usually smaller than VCEO. The voltages VSUS can be
attained only for relatively lower values of collector current. At higher collector current
the limit on the total power dissipation defines the boundary of the allowable active
region as shown in Fig .
At still higher levels of collector currents the allowable active region is further
restricted by a potential failure mode called the Second break down. It appears on
the output characteristics of the BJT as a precipitous drop in the collector-emitter
voltage at large collector currents. The collector voltage drop is often accompanied by
significant rise in the collector current and a substantial increase in the power
dissipation. Most importantly this dissipation is not uniformly spread over the entire
volume of the device but is concentrated in highly localized regions. This localized
heating is a combined effect of the intrinsic non uniformity of the collector current
density distribution across the cross section of the device and the negative
temperature coefficient of resistively of minority carrier devices which leads to the
formation of current filamements (localized areas of very high current density) by a
positive feed-back mechanism. Once current filaments are formed localized thermal
runaway quickly takes the junction temperature beyond the safe limit and the device
is destroyed.
It is in the saturation region that the output characteristics of a Power transistor
differ significantly from its signal level counterpart. In fact the saturation region of a
Power transistor can be further subdivided into a quasi saturation region and a hard
saturation region. Appearance of the quasi saturation region in the output
characteristics of a power transistor is a direct consequence of introducing the drift
region into the structure of a power transistor. In the quasi saturation region the basecollector junction is forward biased but the lightly doped drift region is not completely
shorted out by excess minority carrier injection from the base. The resistivity of this
region depends to some extent on the base current. Therefore, in the quasi saturation
region, the base current still retains some control over the collector current although
the value of decreases significantly. Also, since the resistivity of the drift region is still
significant the total voltage drop across the device in this mode of operation is higher
for a given collector current compared to what it will be in the hard saturation region.
In the hard saturation region base current looses control over the collector current
which is determined entirely by the collector load and the biasing voltage VCC. This
behavior is similar to what happens in a signal transistor except that the drift region of
a power transistor continues to offer a small resistance even when it is completely
shorted out (by excess carrier injection from the base). Therefore, for larger collector
currents the collector-emitter voltage drop is almost proportional to the collector
current. Manufacturers usually provide the plots of the variation of VCE (sat) vs. iC for
different values of base current and junction temperature. Curves showing the variation
26
Electronics
of VCE (sat) with iB for different values of iC and junction temperature are also provided
by certain manufacturers.
Applicable operating limits on a power transistors are compactly represented in two
diagrams called the Forward Bias Safe Operating Area (FBSOA) and the Reverse Bias
Safe Operating Area. (RBSOA) applicable to iB > 0 and iB 0 conditions respectively.
Typical safe operating areas of power transistors are shown in Fig .
Safe operating areas of a Power Transistor. (a) FBSOA; (b) RBSOA.

The horizontal upper limit of the FBSOA is determined by the maximum allowable
collector current (ICM) that should not be exceeded even as a pulse. Exceeding this
current limit may cause bonding wire or metallization of the wafer to vaporize or
otherwise fail. Since a power transistor does not have any appreciable reverse voltage
blocking capacity they are usually not used in ac circuits. However, if the collector
current, for some reason is not dc or a pulse, the rms value of the collector current
waveform should not exceed this limit.
The next applicable limit in the FBSOA (green lines) corresponds to the restriction on
the maximum allowable power dissipation and maximum junction temperature. Since
FBSOA is shown on a log-log scale constant Power dissipation (Pd = VCE iC) limits appear
as straight lines. This limit is different for dc and pulsed operation due to the thermal
time constant of the device. The DC limit is applicable to the average power loss if
the transistor remains continuously in the conduction state (active, quasi saturation or
saturation). On the other hand the pulsed power dissipation limits are applicable to
conduction duration up to the value marked on them (the figures on the right of Fig
(a)). Pulsed power dissipation limits are specified for a low value (1%-2%) of duty cycle
and are useful for shaping the switching trajectory of the transistor as will be seen later.
The third limit of the FBSOA (red line) arises due to the second break down failure
mode of a Power transistor. It shows the limiting combinations of collector voltage and
current so that second break down does not occur. On the log log scale of the FBSOA
this limit also appears as a straight limit. Like the maximum power dissipation limit, the
second break down limit is also different for DC and Pulsed operation of different
pulse durations. The interpretation of the pulse duration (marked on the right side of
Fig (a)) corresponding to a particular limit is also same.
The final limit of the FBSOA corresponds to the forward biased avalanche break
down voltage (VSUS) of the transistor and appear as a vertical line in the FBSOA at VCE =
VSuS
The FBSOA of a Power transistor is given at a specified case temperature. Both the
maximum power dissipation limit and the second break down limits are to be rated as
27
Electronics
per the rating characteristics provided by the manufacturers when the case
temperature exceeds the specified value.
In contrast to the FBSOA, the RBSOA (Fig (b)) is plotted on a linear scale and has a
more rectangular shape. RBSOA is a switching SOA since a transistor cannot conduct
current for any appreciable duration under reverse biased condition. It essentially
shows the limiting permissible combinations of VCE & iC with base emitter junction
reverse biased. The upper horizontal limit corresponds to the maximum allowable
collector current (ICM) and is same as that in the FBSOA. The right hand side vertical
limit corresponds the avalanche break down voltage of the transistor with reverse bias.
If the base terminal is open (i,e, iB = 0) then this voltage is VCEO. If a negative voltage is
applied across the BE junction the right hand side limit of the RBSOA increases
somewhat to the value VCBO at low value of the collector current.
In addition to the applicable limits on the output characteristics as represented in
the FBSOA and the RBSOA, limiting specification with respect to the base emitter
junction is also provided by the manufacturer. Typical specifications that are provided
are
VEBO : This is maximum allowable reverse bias voltage across the B-E junction
IB
: Maximum allowable average base current at a given case temperature.
IBM : Maximum allowable peak base current at a given case temperature and of
specified
pulse duration.
The input characteristics (iB Vs VBE) at a given case temperature is also provided.
Part-A Question
1. What are the advantages of GTO over SCR?
2. Compare Power MOSFET and BJT.
3. What are the drawbacks of GTO?
Part-B Question
1.Briefly discuss the V-I characteristics of BJT.
2.Draw and explain the switching characteristics of GTO.
Topic
Sub Topics
Power Semiconductor- Insulated Gate Bipolar Transistor (IGBT)

Structure, Ton-Toff , V-I Characteristics of IGBT
5. POWER SEMICONDUCTOR- Insulated Gate Bipolar Transistor (IGBT)

5.1.Constructional Features of an IGBT
Vertical cross section of a n channel IGBT cell is shown in Fig . Although p channel IGBTs
are possible n channel devices are more common and will be the one discussed in this
lesson.
28
Electronics
Vertical cross section of an IGBT cell.

The major difference with the corresponding MOSFET cell structure lies in the
addition of a p+ injecting layer. This layer forms a pn junction with the drain layer and
injects minority carriers into it. The n type drain layer itself may have two different
doping levels. The lightly doped n- region is called the drain drift region. Doping level
and width of this layer sets the forward blocking voltage (determined by the reverse
break down voltage of J2) of the device. However, it does not affect the on state voltage
drop of the device due to conductivity modulation as discussed in connection with the
power diode. This construction of the device is called Punch Trough (PT) design. The
Non-Punch Through (NPT) construction does not have this added n+ buffer layer. The
PT construction does offer lower on state voltage drop compared to the NPT
construction particularly for lower voltage rated devices. However, it does so at the
cost of lower reverse break down voltage for the device, since the reverse break down
voltage of the junction J1 is small. The rest of the construction of the device is very
similar to that of a vertical MOSFET including the insulated gate structure and the
shorted body (p type) emitter (n+ type) structure. The doping level and physical
geometry of the p type body region however, is considerably different from that of a
MOSFET in order to defeat the latch up action of a parasitic thyristor embedded in the
IGBT structure. A large number of basic cells as shown in Fig. are grown on a single
silicon wafer and connected in parallel to form a complete IGBT device.
Operating principle of an IGBT
Operating principle of an IGBT can be explained in terms of the schematic cell
structure and equivalent circuit of Fig (a) and (c). From the input side the IGBT behaves
essentially as a MOSFET. Therefore, when the gate emitter voltage is less than the
threshold voltage no inversion layer is formed in the p type body region and the device
is in the off state. The forward voltage applied between the collector and the emitter
drops almost entirely across the junction J2. Very small leakage current flows through
the device under this condition. In terms of the equivalent current of Fig 1.29(c), when
the gate emitter voltage is lower than the threshold voltage the driving MOSFET of the
Darlington configuration remains off and hence the output p-n-p transistor also remains
off.
Parastic thyristor in an IGBT cell.

(a) Schematic structure (b) Exact equivalent circuit (c) Approximate
equivalent circuit
29
Electronics
When the gate emitter voltage exceeds the threshold, an inversion layer forms in
the p type body region under the gate. This inversion layer (channel) shorts the emitter
and the drain drift layer and electron current flows from the emitter through this
channel to the drain drift region. This in turn causes substantial hole injection from the
p+ type collector to the drain drift region. A portion of these holes recombine with the
electrons arriving at the drain drift region through the channel. The rest of the holes
cross the drift region to reach the p type body where they are collected by the source
metallization.
From the above discussion it is clear that the n type drain drift region acts as the base
of the output p-n-p transistor. The doping level and the thickness of this layer
determine the current gain of the p-n-p transistor. This is intentionally kept low so
that most of the device current flows through the MOSFET and not the output p-n-p
transistor collector. This helps to reduce the voltage drop across the body spreading
resistance shown in Fig (b) and eliminate the possibility of static latch up of the IGBT.
The total on state voltage drop across a conducting IGBT has three components. The
voltage drop across J1 follows the usual exponential law of a pn junction. The next
component of the voltage drop is due to the drain drift region resistance. This
component in an IGBT is considerably lower compared to a MOSFET due to strong
conductivity modulation by the injected minority carriers from the collector. This is the
main reason for reduced voltage drop across an IGBT compared to an equivalent
MOSFET. The last component of the voltage drop across an IGBT is due to the channel
resistance and its magnitude is equal to that of a comparable MOSFET.
5.2 Switching characteristics of IGBT
Switching characteristics of the IGBT will be analyzed with respect to the clamped
inductive switching circuit shown in Fig .(a). The equivalent circuit of the IGBT shown in
Fig .(b) will be used to explain the switching waveforms.
(a)
Fig. Inductive switching circuit using an IGBT

Switching circuit (b) Equivalent circuit of the IGBT
The switching waveforms of an IGBT are, in many respects, similar to that of a

Power MOSFET. This is expected, since the input stage of an IGBT is a MOSFET as shown
in Fig (b). Also in a modern IGBT a major portion of the total device current flows
through the MOSFET. Therefore, the switching voltage and current waveforms exhibit a
strong similarity with those of a MOSFET. However, the output p-n-p transistor does
have a significant effect on the switching characteristics of the device, particularly
during turn off. Another important difference is in the gate drive requirement. To avoid
30
Electronics
dynamic latch up, (to be discussed later) the gate emitter voltage of an IGBT is
maintained at a negative value when the device is off.
Fig. Switching waveform of an IGBT

The switching waveforms of an IGBT are shown in Fig 1.32. Similarity of these
waveforms with those of a MOSFET is obvious. To turn on the IGBT the gate drive
voltage changes from Vgg to +Vgg. The gate emitter voltage VgE follows Vgg with a time
constant 1. Since the drain source voltage of the drive MOSFET is large the gate drain
capacitor assumes the lower value CGD1. The collector current ic does not start
increasing till VgE reaches the threshold voltage VgE (th). Thereafter, ic increases
following the transfer characteristics of the device till VgE reaches a value VgE IL
corresponding to ic = iL. This period is called the current rise time tri. The freewheeling
diode current falls from IL to zero during this period. After ic reaches IL, VgE becomes
clamped at VgE IL similar to a MOSFET. VCE also starts falling during this period. First VCE
falls rapidly (tfv1) and afterwards the fall of VCE slows down considerably. Two factors
contribute to the slowing down of voltage fall. First the gate-drain capacitance Cgd will
increase in the MOSFET portion of the IGBT at low drain-source voltages. Second, the
pnp transistor portion of the IGBT traverses the active region to its on state more slowly
than the MOSFET portion of the IGBT. Once the pnp transistor is fully on after tfv2, the on
state voltage of the device settles down to VCE (sat). The turn ON process ends here.
The turn off process of an IGBT follows the inverse sequence of turn ON with one
major difference. Once VgE goes below VgE (th) the drive MOSFET of the IGBT equivalent
circuit turns off. During this period (tfi1) the device current falls rapidly. However, when
the drive MOSFET turns off, some amount of current continues of flow through the
output p-n-p transistor due to stored charge in its base. Since there is no reverse
voltage applied to the IGBT terminals that could generate a negative drain current,
there is no possibility for removing the stored charge by carrier sweep-out. The only
way these excess carriers can be removed is by recombination within the IGBT. During
this recombination period (tfi2) the remaining current in the IGBT decays relatively
slowly forming a current fail. A long tfi2 is undesirable, because the power dissipation in
this interval will be large due to full collector-emitter voltage. tfi2 can be reduced by
decreasing the excess carrier life time in the p-n-p transistor base. However, in the
process, on state losses will increase. Therefore, judicious design tradeoffs are made in
a practical IGBT to give minimum total loss.
5.3 Steady state characteristics of an IGBT
31
Electronics
The i-v characteristics of an n channel IGBT is shown in Fig (a). They appear
qualitatively similar to those of a logic level BJT except that the controlling parameter is
not a base current but the gate-emitter voltage.
Static characteristics of an IGBT

(a) Output characteristics; (b) Transfer characteristics
When the gate emitter voltage is below the threshold voltage only a very small
leakage current flow though the device whiles the collector emitter voltage almost
equals the supply voltage (point C in Fig .(a)). The device, under this condition is said to
be operating in the cut off region. The maximum forward voltage the device can
withstand in this mode (marked VCES in Fig (a)) is determined by the avalanche break
down voltage of the body drain p-n junction. Unlike a BJT, however, this break down
voltage is independent of the collector current as shown in Fig .(a). IGBTs of Non-punch
through design can block a maximum reverse voltage (VRM) equal to VCES in the cut
off mode. However, for Punch through IGBTs VRM is negligible (only a few tens of volts)
due the presence of the heavily doped n+ drain buffer layer.
As the gate emitter voltage increases beyond the threshold voltage the IGBT
enters into the active region of operation. In this mode, the collector current ic is
determined by the transfer characteristics of the device as shown in Fig (b). This
characteristic is qualitatively similar to that of a power MOSFET and is reasonably linear
over most of the collector current range. The ratio of ic to (VgE VgE (th)) is called the
forward transconductance (gfs) of the device and is an important parameter in the gate
drive circuit design. The collector emitter voltage, on the other hand, is determined by
the external load line ABC as shown in Fig (a). As the gate emitter voltage is increased
further ic also increases and for a given load resistance (RL) VCE decreases. At one point
VCE becomes less than VgE VgE(th). Under this condition the driving MOSFET part of the
IGBT (Fig (c)) enters into the ohmic region and drives the output p-n-p transistor to
saturation. Under this condition the device is said to be in the saturation mode. In the
saturation mode the voltage drop across the IGBT remains almost constant reducing
only slightly with increasing VgE.
In power electronic applications an IGBT is operated either in the cut off or in the
saturation region of the output characteristics. Since VCE decreases with increasing VgE,
it is desirable to use the maximum permissible value of VgE in the ON state of the
device. VgE (Max) is limited by the maximum collector current that should be permitted
to flow in the IGBT as dictated by the latch-up condition discussed earlier. Limiting VgE
also helps to limit the fault current through the device. If a short circuit fault occurs in
the load resistance RL (shown in the inset of Fig. (a)) the fault load line is given by CF.
Limiting VgE to VgE6 restricts the fault current corresponding to the operating point F.
Most IGBTs are designed to with stand this fault current for a few microseconds within
which the device must be turned off to prevent destruction of the device.
32
Electronics
It is interesting to note that an IGBT does not exhibit a BJT-like second break
down failure. Since, in an IGBT most of the collector current flows through the drive
MOSFET with positive temperature coefficient the effective temperature coefficient of
VCE in an IGBT are slightly positive. This helps to prevent second break down failure of
the device and also facilitates paralleling of IGBTs.
Part-A Question
List the advantages of the IGBT.
Part-B Question
1.Explain the turn-on and turn-of characteristics of IGBT with neat waveforms.
2.Discuss in detail the static and switching characteristics of IGBT.
Topic
Power Semiconductor- Metal Oxide Semiconductor Field Effect Transistor

(MOSFET)
Sub Topics Structure, Ton-Toff , V-I Characteristics of MOSFET
6. POWER SEMICONDUCTOR- MOSFET
6.1 Constructional Features of a Power MOSFET
As mentioned in the introduction section, Power MOSFET is a device that evolved
from MOS integrated circuit technology. The first attempts to develop high voltage
MOSFETs were by redesigning lateral MOSFET to increase their voltage blocking
capacity. The resulting technology was called lateral double defused MOS (DMOS).
However it was soon realized that much larger breakdown voltage and current ratings
could be achieved by resorting to a vertically oriented structure. Since then, vertical
DMOS (VDMOS) structure has been adapted by virtually all manufacturers of Power
MOSFET. A power MOSFET using VDMOS technology has vertically oriented three layer
structure of alternating p type and n type semiconductors as shown in Fig (a) which is
the schematic representation of a single MOSFET cell structure. A large number of such
cells are connected in parallel (as shown in Fig (b)) to form a complete device.
Schematic construction of a power MOSFET

(a)
Construction of a single cell. (b) Arrangement of cells in a device.
The two n+ end layers labeled Source and Drain are heavily doped to
approximately the same level. The p type middle layer is termed the body (or
substrate) and has moderate doping level (2 to 3 orders of magnitude lower than n+
regions on both sides). The n- drain drift region has the lowest doping density.
Thickness of this region determines the breakdown voltage of the device. The gate
terminal is placed over the n- and p type regions of the cell structure and is insulated
33
Electronics
from the semiconductor body be a thin layer of silicon dioxide (also called the gate
oxide). The source and the drain region of all cells on a wafer are connected to the
same metallic contacts to form the Source and the Drain terminals of the complete
device. Similarly all gate terminals are also connected together. The source is
constructed of many (thousands) small polygon shaped areas that are surrounded by
the gate regions. The geometric shape of the source regions, to some extent,
influences the ON state resistance of the MOSFET.
Parasitic BJT in a MOSFET cell.

One interesting feature of the MOSFET cell is that the alternating n+ n- p n+ structure
embeds a parasitic BJT (with its base and emitter shorted by the source metallization)
into each MOSFET cell as shown in Fig. The nonzero resistance between the base and
the emitter of the parasitic npn BJT arises due to the body spreading resistance of the p
type substrate. In the design of the MOSFET cells special care is taken so that this
resistance is minimized and switching operation of the parasitic BJT is suppressed. With
an effective short circuit between the body and the source the BJT always remain in cut
off and its collector-base junction is represented as an anti parallel diode (called the
body diode) in the circuit symbol of a Power MOSFET.
Operating principle of a MOSFET
At first glance it would appear that there is no path for any current to flow
between the source and the drain terminals since at least one of the p n junctions
(source body and body-Drain) will be reverse biased for either polarity of the applied
voltage between the source and the drain. There is no possibility of current injection
from the gate terminal either since the gate oxide is a very good insulator. However,
application of a positive voltage at the gate terminal with respect to the source will
convert the silicon surface beneath the gate oxide into an n type layer or channel,
thus connecting the Source to the Drain as explained next. The gate region of a
MOSFET which is composed of the gate metallization, the gate (silicon) oxide layer and
the p-body silicon forms a high quality capacitor. When a small voltage is application to
this capacitor structure with gate terminal positive with respect to the source (note that
body and source are shorted) a depletion region forms at the interface between the Si O2
and the silicon as shown in Fig (a).
34
Electronics
Gate control of MOSFET conduction. (a) Depletion layer formation; (b) Free
electron accumulation; (c) Formation of inversion layer.
The positive charge induced on the gate metallization repels the majority hole
carriers from the interface region between the gate oxide and the p type body. This
exposes the negatively charged acceptors and a depletion region is created. Further
increase in VGS causes the depletion layer to grow in thickness. At the same time the
electric field at the oxide-silicon interface gets larger and begins to attract free
electrons as shown in Fig (b). The immediate source of electron is electron-hole
generation by thermal ionization. The holes are repelled into the semiconductor bulk
ahead of the depletion region. The extra holes are neutralized by electrons from the
source.
As VGS increases further the density of free electrons at the interface becomes
equal to the free hole density in the bulk of the body region beyond the depletion layer.
The layer of free electrons at the interface is called the inversion layer and is shown in
Fig (c). The inversion layer has all the properties of an n type semiconductor and is a
conductive path or channel between the drain and the source which permits flow of
current between the drain and the source. Since current conduction in this device takes
place through an n- type channel created by the electric field due to gate source
voltage it is called Enhancement type n-channel MOSFET.
The value of VGS at which the inversion layer is considered to have formed is
called the GateSource threshold voltage VGS (th). As VGS is increased beyond VGS(th)
the inversion layer gets somewhat thicker and more conductive, since the density of
free electrons increases further with increase in VGS. The inversion layer screens the
depletion layer adjacent to it from increasing VGS. The depletion layer thickness now
remains constant.
6.2 Switching characteristics of a MOSFET
The switching behavior of a MOSFET will be described in relation to the clamped
inductive circuit shown in Fig (a). For simplicity the load current is assumed to remain
constant over the small switching interval. Also the diode DF is assumed to be ideal with
no reverse recovery current. The gate is assumed to be driven by an ideal voltage
source giving a step voltage between zero and Vgg in series with an external gate
resistance Rg.
35
Electronics
(a) Clamped inductive switching circuit using a MOSFET

(b) Switching waveforms of a clamped inductive switching circuit
using MOSFET
To turn the MOSFET on, the gate drive voltage changes from zero to Vgg. The
gate source voltage which was initially zero starts rising towards Vgg with a time
constant 1 = Rg (CGS + CGD1) as shown in Fig Note that during this period the drain
voltage VDS is clamped to the supply voltage VD through the freewheeling diode DF.
Therefore, CGS and CGD can be assumed to be connected in parallel effectively. A part of
the total gate current ig charges CGS while the other part discharges CGD. Till VGS
reaches VGS (th) no drain current flows. This time period is called turn on delay time
(td(ON)). Note that td(ON) can be controlled by controlling Rg. Beyond td(ON) iD
increases linearly with vGS and in a further time tri (current rise time) reaches Io. The
corresponding value of vGS and ig are marked as VGS Io and ig Io respectively in Fig .
At this point the complete load current has been transferred to the MOSFET from the
freewheeling diode DF. iD does not increase byond this point. Since in the active region
iD and VGS are linearly related, VGS also becomes clamped at the value vGSIo. The gate
current ig now discharges CGD and the drain voltage starts falling.
(1.12)
The fall of VDS occurs in two distinct intervals. When the MOSFET is in the active region
(VDS > (VGS VGS (th)) CGD = CGD1.Since CGD1 << CGD2, VDS falls rapidly. This fast fall time of
VDS is marked tfv1 in Fig (b). However, once in the ohmic region, CGD = CGD2 >>CGD1.
Therefore, rate of fall of VDS slows down considerably (tfv2). Once VDS reaches its on state
value (rDS(ON) Io) VDS becomes unclamped and increases towards Vgg with a time
constant 2 = Rg (CGS + CGD2). Note that all switching periods can be reduced by
increasing Vgg or / and decreasing Rg. The total turn on time is tON = td(ON) + tri + tfv1 +
tfv2.
36
Electronics
To turn the MOSFET OFF, Vgg is reduced to zero triggering the exact reverse process of
turn on to take place. The corresponding waveforms and switching intervals are show in
Fig (b). The total turn off time toff = td(off) + trv1 + trv2 + tfi.
Steady state output i-v characteristics of a MOSFET
The MOSFET, like the BJT is a three terminal device where the voltage on the gate
terminal controls the flow of current between the output terminals, Source and Drain.
The source terminal is common between the input and the output of a MOSFET. The
output characteristics of a MOSFET are then a plot of drain current (iD) as a function of
the Drain Source voltage (VDS) with gate source voltage (VGS) as a parameter. Fig (a)
shows such a characteristics.
Output i-v characteristics of a Power MOSFET (a) i-v characteristics; (b)

Components of ON-state resistance; (c) Electron drift velocity vs Electric
field; (d) Transfer
With gate-source voltage (VGS) below the threshold voltage (VGS (th)) the MOSFET
operates in the cut-off mode. No drain current flows in this mode and the applied drain
source voltage (VDS) is supported by the body-collector p-n junction. Therefore, the
maximum applied voltage should be below the avalanche break down voltage of this
junction (VDSS) to avoid destruction of the device.
When VGS is increased beyond VGS (th) drain current starts flowing. For small
values of VDS
(VDS < (VGS VGS (th)) iD is almost proportional to VDS. Consequently this mode of
operation is called ohmic mode of operation. In power electronic applications a
MOSFET is operated either in the cut off or in the ohmic mode. The slope of the VDS iD
characteristics in this mode is called the ON state resistance of the MOSFET (rDS (ON)).
Several physical resistances as shown in Fig (b) contribute to rDS (ON). Note that rDS
(ON) reduces with increase in VGS. This is mainly due to reduction of the channel
resistance at higher value of VGS. Hence, it is desirable in power electronic applications,
to use as large a gate-source voltage as possible subject to the dielectric break down
limit of the gate-oxide layer.
37
Electronics
At still higher value of VDS (VDS > (VGS VGS (th)) the iD VDS characteristics
deviates from the linear relationship of the ohmic region and for a given VGS, iD tends to
saturate with increase in VDS. The exact mechanism behind this is rather complex. It will
suffice to state that, at higher drain current the voltage drop across the channel
resistance tends to decrease the channel width at the drain drift layer end. In addition,
at large value of the electric field, produced by the large Drain Source voltage, the
drift velocity of free electrons in the channel tends to saturate as shown in Fig (c). As a
result the drain current becomes independent of VDS and determined solely by the gate
source voltage VGS. This is the active mode of operation of a MOSFET. Simple, first
order theory predicts that in the active region the drain current is given approximately
by
(1.9)
Where K is a constant determined by the device geometry.
At the boundary between the ohmic and the active region
(1.10)
Therefore,
(1.11)
Equation (1.11) is shown by a dotted line in Fig (a). The relationship of Equation (1.9)
applies reasonably well to logic level MOSFETs. However, for power MOSFETs the
transfer characteristics
(iD Vs VGS) is more linear as shown in Fig (d).At this point the similarity of the output
characteristics of a MOSFET with that of a BJT should be apparent. Both of them have
three distinct modes of operation, namely, (i)cut off, (ii) active and (iii) ohmic
(saturation for BJT) modes. However, there are some important differences as well.
Unlike BJT a power MOSFET does not undergo second break down.
The primary break down voltage of a MOSFET remains same in the cut off and in the
active modes. This should be contrasted with three different breakdown voltages
(VSUS, VCEO & VCBO) of a BJT.
The ON state resistance of a MOSFET in the ohmic region has positive temperature
coefficient which allows paralleling of MOSFET without any special arrangement for
current sharing. On the other hand, VCE (sat) of a BJT has negative temperature
coefficient making parallel connection of BJTs more complicated.
As in the case of a BJT the operating limits of a MOSFET are compactly
represented in a Safe Operating Area (SOA) diagram as shown in Fig 1.26. As in the
case of the FBSOA of a BJT the SOA of a MOSFET is plotted on a log-log graph. On the
top, the SOA is restricted by the absolute maximum permissible value of the drain
current (IDM) which should not be exceeded even under pulsed operating condition. To
the left, operating restriction arise due to the non zero value of rDS(ON) corresponding
to VGS = VGS(Max). To the right, the first operating restriction is due to the limit on the
maximum permissible junction temperature rise which depends on the power
dissipation inside the MOSFET. This limit is different for DC (continuous) and pulsed
operation of different pulse widths. As in the case of a BJT the pulsed safe operating
areas are useful for shaping the switching trajectory of a MOSFET. A MOSFET does not
38
Electronics
undergo second break down and no corresponding operating limit appears on the
SOA. The final operation limit to the extreme right of the SOA arises due to the
maximum permissible drain source voltage (VDSS) which is decided by the avalanche
break down voltage of the drain -body p-n junction. This is an instantaneous limit.
There is no distinction between the forward biased and the reverse biased SOAs for the
MOSFET. They are identical.
Safe operating area of a MOSFET.

Due to the presence of the anti parallel body diode, a MOSFET cannot block any
reverse voltage. The body diode, however, can carry an RMS current equal to I DM. It also
has a substantial surge current carrying capacity. When reverse biased it can block a
voltage equal to VDSS.
For safe operation of a MOSFET, the maximum limit on the gate source voltage
(VGS (Max)) must be observed. Exceeding this voltage limit will cause dielectric break
down of the thin gate oxide layer and permanent failure of the device. It should be
noted that even static charge inadvertently put on the gate oxide by careless handling
may destroy it. The device user should ground him before handling any MOSFET to
avoid any static charge related problem.
Part-A Question
1.Compare Power MOSFET and BJT.
2.Why MOSFETs are not preferred for low frequency applications?
Part-B Question
1. Compare and contrast the performance characteristics of SCR and MOSFET.
2. Explain the switching characteristics of power MOSFET.
3. Briefly explain about the power MOSFET protection circuits.
Topic
Sub Topics
Switching losses
conduction losses, blocking losses
7. Switching losses
A converter consists of a few controlled and a few uncontrolled devices (diodes).
While the first device is driven to turn-on or off, the uncontrolled device operates
mainly as a slave to the former. Power loss in the converter is the aggregate of these
losses. Occasionally the diode and the controlled device are housed in the same
module. The losses corresponding to each contribute to the temperature rise of the
integrated module.
The losses can be segregated as follows:
39
Electronics
Conduction Losses
Conduction losses are caused by the forward voltage drop when the power
semiconductor is on and can be described by (with reference to an IGBT)
Approximate forward voltage of IGBT and diode
Where I is the current carried by the device and Vce(sat)(I ) is the current dependant
c
c
forward voltage drop. This drop may be expressed as
This relation defines the forward drop of an IGBT in a similar manner to a diode. A part
of the drop is constant while another part is collector current dependent.
The given data should be used as follows: Using the numerical value is the simplest
way to determine conduction losses. The numerical value can be applied if the current
in the device is equal or close to the specified current - data sheet numerical values are
specified for typical application currents. The graph most accurately determines
conduction losses. The conditions in which the data are used should correspond to the
application. To estimate if a power semiconductor rating is appropriate, usually the
values valid for elevated temperature, close to the maximum junction temperature Tjmax
, should be used to calculate power losses because this is commonly the operating
point at nominal load.
Blocking Losses
Blocking losses are generated by a low leakage current through the device with a high
blocking voltage.
Where IL is the leakage current and Vb(I) is the current dependent blocking voltage.
Data sheets indicate leakage current at certain blocking voltage and temperature. The
dependence between leakage current and applied voltage typically is exponential; this
means that using a data sheet value given for a blocking voltage higher than applied
overestimates blocking losses. However in general, blocking losses are small and can
often, but not always, be neglected.
Part-A Question
40
Electronics
1. Define hard-driving or over-driving.

2. What are the different type of losses in switching devices?
3.What losses occur in a thyristor during working conditions?
Topic
Driver and snubber circuit
Sub Topics
Driver, snubber circuit
8.Driver and snubber circuit

8.1 Snubber Circuits
To protect a thyristor, from a large di/dt during turn-on and a large dv/dt during
turn-off, a snubber circuit is needed. A general snubber topology is shown in Fig. The
turn-on snubber is made by inductance L1 (often L1 is stray inductance only). This
protects the thyristor from a large di/dt during the turn-on process. The auxiliary circuit
made by R1 and D1 allows the discharging of L1 when the thyristor is turned off. The
turn-off snubber is made by resistor R2 and capacitance C2. This circuit protects a GTO
from large dv/dt during the turn-off process. The auxiliary circuit made by D2 and R2
allows the discharging of C2 when the thyristor is turned on. The circuit of capacitance
C2 and inductance L1 also limits the value of dv/dt across the thyristor during forwardblocking. In addition, L1 protects the thyristor from reverse over-currents. R1 and
diodes D1, D2 are usually omitted in ac circuits with converter-grade thyristors. A
similar second set of L, C and R may be used around this circuit in HVDC applications.
Turn-on (top elements) and turn-off (bottom elements) snubber circuits for
thyristors.
8.2 Driver Circuits
It is possible to turn on a thyristor by injecting a current pulse into its gate. This process
is known as gating, triggering or firing the thyristor. The most important restrictions are
on the maximum peak and duration of the gate pulse current. In order to allow a fast
turn-on and a correspondingly large anode di/dt during the turn-on process, a large
gate current pulse is supplied during the initial turn-on phase with a large diG/dt. The
gate current is kept on, at lower value, for some times after the thyristor turned on in
order to avoid unwanted turn-off of the device; this is known as the back-porch
current. A shaped gate current waveform of this type is shown in Fig.. Figure shows
typical gate iv characteristics for the maximum and minimum operating temperatures.
The dashed line represents the minimum gate current and corresponding gate voltage
needed to ensure that the thyristor will be triggered at various operating temperatures.
It is also known as the locus of minimum firing points. On the data sheet it is possible
find a line representing the maximum operating power of the thyristor gating internal
circuit. The straight line, between VGG and VGG/RG, represents the current voltage
41
Electronics
characteristic of the equivalent trigger circuit. If the equivalent trigger circuit line
intercepts the two gate iv characteristics for the maximum and minimum operating
temperatures between where they intercept the dashed lines (minimum gate current to
trigger and maximum gate power dissipation), then the trigger circuit is able to turn-on
the thyristor at any operating temperature without destroying or damaging the device.
Gate current waveform showing large initial current followed by a suitable

back-porch value.
In order to keep the power circuit and the control circuit electrically
unconnected, the gate signal generator and the gate of the thyristor are often
connected through a transformer. There is a transformer winding for each thyristor, and
in this way unwanted short circuits between devices are avoided. A general block
diagram of a thyristor gate-trigger circuit is shown in Fig. This application is for a
standard bridge configuration often used in power converters. Another problem can
arise if the load impedance is high, particularly if the load is inductive and the supply
voltage is low. In this situation, the latching current may not be reached during the
trigger pulse. A possible solution to this problem could be the use of a longer current
pulse. However, such a solution is not attractive because of the presence of the
isolation transformer.
Gate iv curve for a typical thyristor.

An alternative solution is the generation of a series of short pulses that last for
the same duration as a single long pulse. A single short pulse, a single long pulse and a
series of short pulses are shown in Fig. Reliable gating of the thyristor is essential in
many applications. There are many gate trigger circuits that use optical isolation
between the logic-level electronics and a drive stage (typically MOSFETs) configured in
a pushpull output. The dc power supply voltage for the drive stage is provided through
transformer isolation. Many device manufacturers supply drive circuits available on
printed circuit (PC) boards or diagrams of suggested circuits. IGCT gate drives consist of
an integrated module to which the thyristor is connected via a low-inductance
mounting; an example is given in Fig. Multiple MOSFETs and capacitors connected in
parallel may be used to source or sink the necessary currents to turn the device on or
42
Electronics
off. Logic in the module controls the gate drive from a fiber-optic trigger input, and
provides diagnostic feedback from a fiber-optic output. A simple power supply
connection is also required.
Block diagram of a transformer-isolated gate drive circuit.
Multiple gate pulses used as an alternative

Typical layout of an IGCT gate drive
to one long Current pulse.
Part-A Question
What is a snubber circuit?
43
Electronics
Topic
Sub Topics
Triggering and Commutation circuits for SCR

Triggering ,Commutation circuits- Natural Commutation, Forced Commutation
9. (a).Triggering circuits for SCR

With anode positive with respect to cathode, a thyristor can be turned on by any
one of the following techniques:
aForward voltage triggering (b)gate triggering (c) dv/dt triggering
(d) Temperature triggering (e) Light triggering.
These methods of turning-on a thyristor are now discussed one after the other.
a Forward Voltage Triggering:
When anode to cathode forward voltage is increased with gate circuit open, the
reverse biased junction J2 will break. This is known as avalanche breakdown and the
voltage at which avalanche occurs is called forward break over voltage VB0. At this
voltage, thyristor changes from off-state (high voltage with low leakage current) to onstate characterized by low voltage across thyristor with large forward current. As other
junctions Jl,J3 are already forward biased, breakdown of junction J2 allows free movement
of carriers across three junctions and as a result, large forward anode-current flows. As
stated before, this forward current is limited by the load impedance. In practice, the
transition from off-state to on-state obtained by exceeding VB0 is never employed as it
may destroy the device.
The magnitudes of forward and reverse break over voltages are nearly the same
and both are temperature dependent. In practice, it is found that VBR is slightly more
than VB0- Therefore, forward break over voltage is taken as the final voltage rating of
the device during the design of SCR applications. After the avalanche breakdown,
junction J2 looses its reverse blocking capability. Therefore, if the anode voltage is
reduced below VB0 SCR will continue conduction of the current. The SCR can now be
turned off only by reducing the anode current below a certain value called holding
current (defined later).
b Gate Triggering :
Turning on of thyristors by gate triggering is simple, reliable and efficient; it is therefore
the most usual method of firing the forward biased SCRs. A thyristor with forward break
over voltage (say 800 V) higher than the normal working voltage (say 400 V) is chosen.
This means that thyristor will remain in forward blocking state with normal working
voltage across anode and cathode and with gate open. However, when turn-on of a
thyristor is required, a positive gate voltage between gate and cathode is applied. With
gate current thus established, charges are injected into the inner p layer and voltage at
which forward breakover occurs is reduced. The forward voltage at which the device
switches to on-state depends upon the magnitude of gate current. Higher the gate
current, lower is the forward breakover voltage.
When positive gate current is applied, gate P layer is flooded with electrons from
the cathode. This is because cathode N layer is heavily doped as compared to gate P
layer. As the thyristor is forward biased, some of these electrons reach junction J2. As a
result, width of depletion layer around junction J2 is reduced. This causes the junction J2
to breakdown at an applied voltage lower than forward breakover voltage VB0. If
magnitude of gate current is increased, more electrons will reach junction J2, as a
44
Electronics
consequence thyristor will get turned on at a much lower forward applied voltage.
c dv/dt triggering:
In this method of triggering if the applied rate of change of voltage is large, then the
device will turn on even though the voltage appearing across the device is small. We
know that when SCR is applied with forward voltage across the anode and cathode,
junctions j1 and j3 will be in forward bias and junction j 2 will be in reverse bias. This
reverse biased junction j2 will have the characteristics of the capacitor due to the
charges exist across the junction. If the forward voltage is suddenly applied a charging
current will flow tending to turn on the SCR. This magnitude of the charging current
depends on the rate of change of applied voltage.
d Temperature Triggering :
During forward blocking, most of the applied voltage appears across reverse
biased junction J2. This voltage across junction J2 associated with leakage current may
raise the temperature of this junction. With increase in temperature, leakage current
through junction J2 further increases. This cumulative process may turn on the SCR at
some high temperature.
e Light Triggering.
For light-triggered SCRs, a recess (or niche) is made in the inner p-layer as shown in
Fig. (a). When this recess is irradiated, free charge carriers (holes and electrons) are
generated just like when gate signal is applied between gate and cathode. The pulse of
light of appropriate wavelength is guided by optical fibres for irradiation. If the intensity
of this light thrown on the recess exceeds a certain value, forward-biased SCR is turned
on. Such a thyristor is known as light-activated SCR (LASCR).
(a) Elementary LASCR

(b) Structural details of conventional
centre-gate thyristor
LASCR may be triggered with a light source or with a gate signal. Sometimes a
combination of both light source and gate signal is used to trigger an SCR. For this, the
gate is biased with voltage or current slightly less than that required to turn it on, now a
beam of light directed at the inner p-layer junction turns on the SCR. The light intensity
required to turn-on the SCR depends upon the voltage bias given to the gate. Higher
the voltage (or current) bias, lower the light intensity required. Light-triggered
thyristors have now been used in high-voltage direct current (HVDC) transmission
systems. In these several SCRs are connected in series-parallel combination and their
light-triggering has the advantage of electrical isolation between power and control
45
Electronics
circuits.
9. (b). Commutation circuits for SCR
A thyristor can be turned on by triggering gate terminal with low voltage short
duration pulse. But after turning on, it will conduct continuous until the thyristor is
reverse biased or the load current falls to zero. This continuous conduction of thyristors
causes problems in some applications. The process used for turning off a thyristor is
called as commutation. By the commutation process, the thyristor operating mode is
changed from forward conducting mode to forward blocking mode. So, the thyristor
commutation methods or thyristor commutation techniques are used to turn off.
The commutation techniques of thyristors are classified into two types:
(i)
Natural Commutation
(ii)
Forced Commutation
(i)
Natural Commutation
Generally, if we consider AC supply, the current will flow through the zero crossing
line while going from positive peak to negative peak. Thus, a reverse voltage will
appear across the device simultaneously, which will turn off the thyristor
immediately. This process is called as natural commutation as thyristor is turned off
naturally without using any external components or circuit or supply for
commutation purpose.
Natural commutation can be observed in AC voltage controllers, phase controlled

rectifiers
and cycloconverters.
(ii) Forced Commutation
The thyristor can be turned off by reverse biasing the SCR or by using active or passive
components. Thyristor current can be reduced to a value below the value of holding
current. Since, the thyristor is turned off forcibly it is termed as a forced commutation
process. The basic electronics and electrical components such as inductance and capacitance
are used as commutating elements for commutation purpose.Forced commutation can
be observed while using DC supply; hence it is also called as DC commutation. The
external circuit used for forced commutation process is called as commutation circuit
and the elements used in this circuit are called as commutating elements.
a)
b)
c)
d)
e)
Classification of Forced Commutation Methods

The forced commutation can be classified into different methods as follows:
Class A: Self commutated by a resonating load
Class B: Self commutated by an LC circuit
Class C: Cor L-C switched by another load carrying SCR
Class D: C or L-C switched by an auxiliary SCR
Class E: An external pulse source for commutation
46
Electronics
(a) Class A: Self Commutated by a Resonating Load

Class A is one of frequently used thyristor commutation techniques. If thyristor is
triggered or turned on, then anode current will flow by charging capacitor C with dot as
positive. The second order under-damped circuit is formed by the inductor or AC resistor,
capacitor and resistor. If the current builds up through SCR and completes the half
cycle, then the inductor current will flow through the SCR in the reverse direction which
will turn off thyristor. After the thyristor commutation or turning off the thyristor, the
capacitor will start discharging from its peak value through the resistor is an
exponential manner. The thyristor will be in reverse bias condition until the capacitor
voltage returns to the supply voltage level.
(b) Class B: Self commutated by an LC circuit

The major difference between the class A and class B thyristor commutation
techniques is that the LC is connected in series with thyristor in class A, whereas in
parallel with thyristor in class B. Before triggering on the SCR, the capacitor is charged
up (dot indicates positive). If the SCR is triggered or given triggering pulse, then the
resulting current has two components. The constant load current flowing through the RL load is ensured by the large reactance connected in series with the load which is
clamped with freewheeling diode. If sinusoidal current flows through the resonant L-C
circuit, then the capacitor C is charged up with dot as negative at the end of the half
cycle.The total current flowing through the SCR becomes zero with the reverse current
flowing through the SCR opposing the load current for a small a small fraction of the
negative swing. If the resonant circuit current or reverse current
becomes just greater than the load current, then the SCR will be
turned OFF.
(c)
Class C: Cor L-C switched by another load carrying SCR
In the above thyristor commutation techniques we observed only

one SCR but in these class C commutation techniques of thyristor
there will be two SCRs. One SCR is considered as main thyristor and
the other as auxiliary thyristor. In this classification both may act as
main SCRs carrying load current and they can be designed with four SCRs with load
across the capacitor by using a current source for supplying an integral converter. If the
thyristor T2 is triggered, then the capacitor will be charged up. If the thyristor T1 is
triggered, then the capacitor will discharge and this discharge
current of C will oppose the flow of load current in T2 as the
capacitor is switched across T2 via T1.
(d)
Class D: C or L-C switched by an auxiliary SCR

The class C and class D thyristor commutation techniques can be
47
Electronics
differentiated with the load current in class D: only one of the SCRs will carry the load
current while the other acts as an auxiliary thyristor whereas in class C both SCRs will
carry load current. The auxiliary thyristor consists of resistor in its anode which is
having resistance of approximately ten times the load resistance. By triggering the Ta
(auxiliary thyristor) the capacitor is charged up to
supply voltage and then the Ta will turn OFF. The extra
voltage if any, due to substantial inductance in the
input lines will be discharged through the diodeinductor-load circuit. If the Tm (main thyristor) is
triggered, then the current will flow in two paths:
commutating current will flow through the C-Tm-L-D
path and load current will flow through the load. If the charge on the capacitor is
reversed and held at that level using the diode and if Ta is re-triggered, then the
voltage across the capacitor will appear across the Tm via Ta. Thus, the main thyristor
Tm will be turned off.
(e) Class E: An external pulse source for commutation
For the class E thyristor commutation techniques, a transformer which cannot
saturate (as it is having a sufficient iron and air gap)
and capable to carry the load current with small
voltage drop compared with the supply voltage. If the
thyristor T is triggered, then the current will flow
through the load and pulse transformer. An external
pulse generator is used to generate a positive pulse
which is supplied to the cathode of the thyristor
through pulse transformer. The capacitor C is charged
to around 1v and it is considered to have zero impedance for the turn off pulse
duration. The voltage across the thyristor is reversed by the pulse from the electrical
transformer which supplies the reverse recovery current, and for the
required turn off time it holds the negative voltage.
Part-A Question
1.List the various forced commutation techniques used to turn off SCR.
2.What is meant by current communication of SCR?
Part-B Question
Discuss the working of a complementary commutation circuit of SCR with a neat circuit
diagram and
waveforms
OBJECTIVE QUESTIONS
1. Silicon based rectifiers are preferred than germanium based rectifiers because
(a) Si is available easily compared to Ge (b) Only Si has a stable off state
(c) Ge is very temperature sensitive
48
Electronics
(d) Si only has the characteristics 1 + 2 < 1 at low collector currents and reaches
1 at high currents
Which of the above statements are true?
(a) A, B, D
(b) B, D
(c) B Only
(d) D Only
2. In a triac,
(a) The triggering pulse to main terminal 1 should be of the same polarity as the
anode potential
Between MT1 and MT2
(b)The triggering pulse should be of opposite polarity to that of anode potential
(c) When the triggering pulse is positive and anode is positive, it is operating in the
first quadrant
(d)When the triggering pulse is negative and anode is negative its sensitivity is
highest.
(a)A, D
(b) A, C
(c) C, D
(d) A, C, D
3. In a single phase full wave SCR circuit with R, L load
(a) Power is delivered to the source for firing angle of less than 90
(b) The scr changes from inverter to converter at = 90
(c) The negative dc voltage is maximum at = 180
(d) To turn off the scr, the maximum delay angle must be less than 180
(a)C, D
(b) C Only
(c) D Only
(d) A, B
4. While comparing triac and scr,
(a) Both are unidirectional devices
(b) Triac requires more current for turn on than scr at particular voltages
(c) A triac has less time for turn off than SCR
(d) Both are available with comparable voltage and current ratings
(b)A, C
(b) B, C
(c) A, B
(d) Only
5. Which of the following statements are true
(a) If the SCR, even with proper gate excitation and anode-cathode voltage does not
conduct for a
particular load resistance, then it would be necessary to decrease the load
resistance to turn ON
the SCR
(c) The SCR would be turned OFF by voltage reversal of the applied anode-cathode ac
supply of
frequencies up to 30kHz
(d)If the gate current of the SCR is increased, then the forward breakdown voltage will
decrease
(a) A, B, C
(b) B, C
(c) A , C
(d) A, B
6. Which of the following statements are true
When gate triggering is employed, a SCR can withstand higher values of di/dt, if the
(a) Gate current is increased
(b) Rate of rise of gate current is
increased
(c) Gate current is increased
(d) Rate of rise of gate current is
decreased
49
Electronics
(a) 3, 4
(b) 1, 4
(c) 2, 3
7. In a SCR based converter, the freewheeling diode is used to
(d) 1, 2
(a)Add to the conduction current of thyristors

conduction
(b) Oppose the SCR
(c) Conduct current during the OFF period of the SCR

providing a shunt path
(d) Protect the SCR by
8. Snubber circuit is used to limit the rate of

(a) Rise of current
the above
(b) Conduction period (c) Rise of voltage across SCR (d) None of
9. The provision of a freewheeling diode across an inductive load is

(a) To restore conduction angle on phase (b) To avoid negative reversal voltage drop
(c) To reduce the PRV
(d) None of the above
10. While working in series operation, equalizing circuits are added across each SCR to
provide uniform
(a) Current distribution (b) Firing of SCRs (c) Voltage distribution (d) None of the
above
11. When the SCR conducts, the forward voltage drop
(a) Is 0.7V (b) Is 1 to 1.5V (c) Increases slightly with load current (d) Remains
constant with load
current
(a) a only
(b) b, c
(c) d only
(d) a, c
12. The latching current of a SCR is 18mA. Its holding current will be
(a) 6mA
(d) 12mA
(b) 18mA
(c) 54mA
13. In thyristor, holding current is

(a) more than the latching current
(b) less than the latching current
(c) equal to latching current
(d) none of the above
14. When a thyristor turn on, the gate drive:
(a) can be turned down but thyristor remains in on position
(b) cannot be turned down as thyristor will be turned off
50
Electronics
(c) gate drive has no impact on starting and turning off the thyristor
15. A thyristor can be termed as:
(a) DC switch
(b) AC switch
(c) both AC and DC switch
(d)
none of the above
16. During forward blocking state, a thyristor is associated with:
(a) Large current and low voltage
(b) low current and large voltage
(c) Medium current and large voltage
(d) None of the above
17. Turn-off time of an SCR is measured from the instant:
(a) anode current becomes zero
(b) anode voltage becomes
zero
(c) anode voltage and anode current becomes zero (d) gate current becomes zero
18. A forward voltage can be applied to an SCR after its:
(a) anode current reduces to zero (b) gate recovery time (c) reverse recovery time
(d) anode voltage reduces to zero
19. In a thyristor, the magnitude of the anode current will:
(a)Increase if the gate current is increased (b) decrease if the gate current is
decreased
(c) Increase if gate current is decreased
(d) no change with the variation
of the gate current
20. In a thyristor, ratio of latching current to holding current is:
(a) 0.4
(b) 1.0
(c) 2.5
(d) 4.0
21. Once SCR starts conducting a forward current, its gate losses control over:
(a) anode circuit voltage only
(b) anode circuit current only
(c) anode circuit voltage and current
22. On state voltage drop across thyristor used in a 230 V supply system is of the order:
(a) 110-115V
(b) 250 V
(c) 1- 1.5 V
(d) none of the
above
23. The thyristor will turn on faster with
(a) Pulse signal applied to the gate terminal of the SCR
(b) Continuous signal applied to the gate terminal of the SCR
(c) Both are same
(d) Pulse signal but with minimum duration
(a) a only
(b) b only
(c) a, d
24. In an SCR,
(a) The holding current is less than latching current
(b) The holding current is greater than latching current
(c) The two currents are equal
(d) The latching current is about 3 times the holding current
(a) a only (b) d only (c) a, c, d (d) a, d (e) b only
25. When a positive voltage is applied to the gate of a reverse biased SCR
(a) It injects more electrons into junction J1
(b) It increases reverse leakage current into anode
(c) Heating of junction is unaffected
(d) Failure of junctions occurs due to thermal runaway
51
Electronics

(a) b only
(b) a, b ,d
(c) b, d
1 2 3 4 5 6 7 8 9 1
0
b d a b c a c c a c
1
1
b
1
2
a
1
3
b
1
4
a
52
(d) d only
1
5
a
1
6
b
1
7
a
1
8
b
1
9
d
2
0
c
2
1
c
2
2
c
2
3
c
2
4
d
2
5
c

Unit I Power Semi-Conductor Devices: Topic Sub Topics

Uploaded by

Copyright:

Available Formats

Unit I Power Semi-Conductor Devices: Topic Sub Topics

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Unit I Power Semi-Conductor Devices: Topic Sub Topics

Uploaded by

Copyright:

Available Formats

KCE/DEPT.OF.

Subject Code/Name: EE6503/Power

Study of Switching Devices

1. STUDY OF SWITCHING DEVICES

Subject Code/Name: EE6503/Power

1.3 POWER SEMICONDUCTOR DEVICES

Power Semiconductor- Diodes

Subject Code/Name: EE6503/Power

2.(a).1 Construction and Characteristics of Power Diodes

Subject Code/Name: EE6503/Power

Forward current and voltage waveforms of a power diode during Turn On

Reverse Recovery characteristics of a power diode

Subject Code/Name: EE6503/Power

Subject Code/Name: EE6503/Power

Subject Code/Name: EE6503/Power

Volt-Ampere ( i-v ) characteristics of a p-n junction diode

Power Semiconductor- Thyristors

Structure, Ton-Toff , V-I Characteristics of Thyristors

Subject Code/Name: EE6503/Power

Constructional features of a thyristor

Subject Code/Name: EE6503/Power

The underlying operating principle of a thyristor is best understood in terms of the

Two transistor analogy of a thyristor construction.

Subject Code/Name: EE6503/Power

Subject Code/Name: EE6503/Power

Turn on characteristics of a thyristor.

Subject Code/Name: EE6503/Power

Turn off characteristics of a thyristor

Subject Code/Name: EE6503/Power

Static output characteristics of a Thyristor

Subject Code/Name: EE6503/Power

Power Semiconductor- Triac

Structure, Ton-Toff , V-I Characteristics of Triac

3. POWER SEMICONDUCTOR- Triac

Subject Code/Name: EE6503/Power

Circuit symbol and schematic construction of a Triac

Conduction mechanism of a triac in trigger modes 1 and 3

Subject Code/Name: EE6503/Power

Steady state V I characteristics of a Triac

RMS ON state current Vs maximum case temperature.

Subject Code/Name: EE6503/Power

Power Semiconductor- GTO

Structure, Ton-Toff , V-I Characteristics of GTO

4.(a) POWER SEMICONDUCTOR- Gate Turn Off Thyristor (GTO)

Subject Code/Name: EE6503/Power

Switching characteristics of a GTO.

Subject Code/Name: EE6503/Power

Steady state characteristics of a GTO

Subject Code/Name: EE6503/Power

Power Semiconductor- Power Bipolar Junction Transistor (BJT)

4.(b) POWER SEMICONDUCTOR- Power Bipolar Junction Transistor (BJT)

Subject Code/Name: EE6503/Power

Constructional Features of a Power Bipolar Junction Transistor

Subject Code/Name: EE6503/Power

Turn ON characteristics of a power transistor; (a) Switching circuit, (b)

Subject Code/Name: EE6503/Power

Subject Code/Name: EE6503/Power

Turn off characteristics of a BJT.