Scribd
Upload
523 views

Interfacing LCD To Arduino

This document discusses interfacing a 16x2 LCD module to an Arduino Uno. It describes the JHD162A LCD module, which has 16 pins and can operate in 4-bit or 8-bit mode. It provides the pin connections and functions. The circuit diagram shows how to connect the LCD's RS, E, and data pins to the Arduino. The code initializes the LCD and prints text to the display. Additional code is provided to scroll text across the screen.

Uploaded by

Shahrim Mohd
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
523 views

Interfacing LCD To Arduino

This document discusses interfacing a 16x2 LCD module to an Arduino Uno. It describes the JHD162A LCD module, which has 16 pins and can operate in 4-bit or 8-bit mode. It provides the pin connections and functions. The circuit diagram shows how to connect the LCD's RS, E, and data pins to the Arduino. The code initializes the LCD and prints text to the display. Additional code is provided to scroll text across the screen.

Uploaded by

Shahrim Mohd
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Interfacing LCD to arduino

Interfacing LCD to Arduino uno.


LCD modules form a very important part in many arduino based embedded system designs. So
the knowledge on interfacing LCD to arduino is very essential in designing embedded systems.
This article is about interfacing a 162 LCD to Arduino. JHD162A is the LCD module used here.
JHD162A is a 162 LCD module based on the HD44780 driver from Hitachi. The JHD162A has
16 pins and can be operated in 4-bit mode or 8-bit mode. Here we are using the LCD module in
4-bit mode. First, I will show you how to display plain text messages on the LCD module using
arduino and then few useful projects using LCD and arduino. Before going in to the details of the
project, lets have a look at the JHD162A LCD module.

JHD162A LCD module 162.


The JHD162A has 16 pins and can be operated in 4-bit mode or 8-bit mode. Here we are using
the LCD module in 4-bit mode. Before going in to the details of the project, lets have a look at the
JHD162A LCD module.The schematic of a JHD162A LCD module is given below.

The name and functions of each pin of the JHD162A LCD module is given below.
Pin1(Vss):Ground pin of the LCD module.

Pin2(Vcc):+5V supply is given to this pin

Pin3(VEE):Contrast adjustment pin. This is done by connecting the ends of a 10K potentimeter
to +5V and ground and then connecting the slider pin to the VEE pin. The voltage at the VEE pin
defines the contrast. The normal setting is between 0.4 and 0.9V.

Pin4(RS):Register select pin.The JHD162A has two registers namely command register and data
register. Logic HIGH at RS pin selects data register and logic LOW at RS pin will select command
register. If we make the RS pin HIGH and put a data on the data lines (DB0 to DB7) it will be
recognized as a data. If we make the RS pin LOW and put a data on the data lines, then it will be
taken as a command.
Pin5(R/W): Read/Write modes. This pin is used for selecting between read and write modes.
Logic HIGH at this pin activates read mode and logic LOW at this pin activates write mode.
Pin6(E): This pin is meant for enabling the LCD module. A HIGH to LOW signal at this pin will
enable the module.
Pin7(DB0) to Pin14(DB7): These are data pins. The commands and data are put on these pins.

Pin15(LED+): Anode of the back light LED. When operated on 5V, a 560 ohm resistor should be
connected in series to this pin. In arduino based projects the back light LED can be powered from
the 3.3V source on the arduino board.

Pin16(LED-): Cathode of the back light LED.


For knowing more about LCD module JHD162A and it interfacing, read this article: Interfacing
162 LCD and 8051 microcontroller. The circuit diagram of interfacing LCD to arduino for
displaying a text message is shown below.

Circuit diagram.

RS pin of the LCD module is connected to digital pin 12 of the arduino. R/W pin of the LCD is
grounded. Enable pin of the LCD module is connected to digital pin 11 of the arduino. In this
project, the LCD module and arduino are interfaced in the 4-bit mode. That means only four of
the digital input lines( DB4 to DB7 of the LCD are used). This method is very simple, requires
less connections and you can almost utilize the full potential of the LCD module. Digital lines
DB4, DB5, DB6 and DB7 are interfaced to digital pins 5, 4, 3 and 2 of the Arduino. The 10K
potentiometer is used for adjusting the contrast of the display. 560 ohm resistor R1 limits the
current through the back light LED. The arduino can be powered through the external power jack
provided on the board. +5V required in some other parts of the circuit can be tapped from the 5V
source on the arduino board. The arduino can be also powered from the PC through the USB
port. The full program for interfacing LCD to arduino is shown below.

Program.
#include<LiquidCrystal.h>

LiquidCrystal lcd(12, 11, 5, 4, 3, 2); // sets the interfacing pins

void setup()
{
lcd.begin(16, 2); // initializes the 16x2 LCD
}

void loop()
{
lcd.setCursor(0,0);

//sets the cursor at row 0 column 0

lcd.print("16x2 LCD MODULE"); // prints 16x2 LCD MODULE


lcd.setCursor(2,1);

//sets the cursor at row 1 column 2

lcd.print("HELLO WORLD");

// prints HELLO WORLD

About the program.


Library function LiquidCrystal.h is used for displaying the desired characters on the LCD
module. It is readily available with the Arduino user interface and it can be accessed through the
Import library in the sketch tab in the main menu bar. The LiquidCrystal.h provides functions
for almost all applications like printing a string, setting the cursor, initializing the LCD, scrolling the
display etc.

Program for scrolling the display.


A simple program for scrolling a text on the LCD using arduino is shown here. This is done using
the scroll() function. For example the function lcd.scrollDisplayRight() will scroll the display to

right and the functionlcd.scrollDisplayLeft() will scroll the display to left. A for loop is used for
selecting the number of positions to scroll at a time. In the program shown below, it is chosen to
be 2 because the text to be displayed is comparatively long. For shorter texts more number of
positions must be scrolled at a time to get a smooth display.

#include <LiquidCrystal.h>
int i=0;

LiquidCrystal lcd(12, 11, 5, 4, 3, 2);

void setup()
{
lcd.begin(16, 2);

//initializes 16x2 LCD

lcd.print("16x2 LCD MODULE JHD162A & ARDUINO-UNO"); //text to display


}

void loop()
{
for(i=0;i<2;i++)
{lcd.scrollDisplayLeft();} //scrolls display left by two positions
delay(800);
}

//sets the speed at which display moves

You might also like