Scribd Logo
Upload

Welcome to Scribd!

  • 557 views

    MS 979 1 1985pre

    Uploaded by

    mrkhairee
    MS 979 Part 1 : 1985

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    MS 979 1 1985pre

    Uploaded by

    mrkhairee
    557 views7 pages
    MS 979 Part 1 : 1985

    Original Title

    MS_979_1_1985pre

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    MS 979 Part 1 : 1985

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    557 views7 pages

    MS 979 1 1985pre

    Uploaded by

    mrkhairee
    MS 979 Part 1 : 1985

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 7

    MS ISO/IEC TR 10037 : 1995

    MALAYSIAN

    STANDARD
    MS 979 : PART 1 : 1985
    ICS : 23.040.20, 83.140.01, 83.140.30

    SPECIFICATION FOR
    UNPLASTICIZED PVC
    UNDERGROUND SEWERAGE
    PIPE AND FITTINGS
    PART 1 : PIPES OF DIAMETER
    100 MILLIMETRE AND
    155 MILLIMETRE

    STANDARDS & INDUSTRIAL RESEARCH INSTITUTE OF MALAYSIA


    Copyright
    1

    SIRIM. No part of this publication may be photocopied or otherwise reproduced


    without the prior permission in writing of SIRIM

    MS 979: Part 1: 1985

    This Malaysian Standard, which had been approved by the Building and Civil Engineering Industry Standards
    Committee and endorsed by the Council of the Standards and Industrial Research Institute of Malaysia (SIRIM) was
    published under the authority of the SIRIM Council in August, 1 985.

    SIRIM wishes to draw attention to the fact that this Malaysian Standard does not purport to include allthe necessary
    provisions of a contract.

    The Malaysian Standards are subject to periodical review to keep abreast of progress in the industries concerned.
    Suggestions for improvements will be recorded and in due course brought to the notice of the Committees charged
    with the revision of the standards to which they refer.

    The following references relate to the work on this standard:


    Committee reference: SIRIM 404/2/5
    Draft for comment: D25 (ISC D)

    Amendments issued since publication


    Amd. No.

    Date of issue

    Text affected

    MS 979: Part 1: 1985

    CONTENTS
    Page
    Committee representation

    Foreword

    Scope

    Material

    Colour

    Freedom from defects

    Dimensions

    Length of pipe

    Marking

    Rubber sealing rings

    Testing

    10

    Sampling procedures

    11

    Requirements for pipe and fittings

    11

    12

    Combined temperature cycling and external loading requirement

    11

    13

    Requirements for elastomeric sealing ring joint assemblies

    12

    14

    Requirement for solvent welded joint assemblies

    12

    Socket dimensions

    i~

    Short radius bends

    14

    Long radius bends

    15

    Single junctions

    i6

    Illustration of minimum depth of spigot

    16

    6a

    Socket plug (Push fit with or without stop flange)

    16

    6b

    Socket plug (With screwed access cap)

    16

    6c

    Single socket (With or without register)

    17

    6d

    Double socket (With or without register)

    17

    7a

    Level invert reducer

    17

    7b

    Access fittings with inspection doors

    17

    7c

    Adaptor

    17

    Effective length of pipe

    18

    Figures

    MS 979: Part 1: 1985

    CONTENTS (CONTD~)

    9
    10

    Suitable type of impact t~stingmachine

    22

    Essential features of apparatus for diameter distortion test

    26

    Tables
    1

    Dimensions of pipe and fittings

    Type tests

    Quality control tests

    Minimum dimensions of sockets with sealing rings

    14

    Minimum dimensions of solvent cement sockets

    15

    Configuration and minimum radii of bends and junctions

    15

    Dimensions of inspection doors

    17

    Test for resistance to acid and alkali (Type test)

    19

    Tensile test (Type test)

    20

    Heat reversion test for pipes (Quality control test)

    21

    Test for impact resistance of pipe at 20C (Quality control test)

    22

    Stress relief test (Quality control test for injection mouldings)

    24

    Hydrostatic pressure test (Quality control test for factory made


    solvent welded assemblies)

    25

    Diameter distortion test (Type test for jointed assemblies)

    26

    Angular deflection test (Type test)

    27

    Elevated temperature cycling test on fittings (Type test)

    28

    Combined temperature cycling and external loading tests (Performance test)

    29

    Sampling quantities for fittings

    31

    Appendices

    MS 979: Part 1 :1985

    Committee representation
    The Building and Civil Engineering Industry Standards committee under whose supervision this Malaysian Standard was prepared, comprises
    representatives from the following Government Ministries, trade, commerce and manufacturer associations and scientific and professional bodies.
    Association of Consulting Engineers IMalaysial
    Institution of Engineers, Maiaysia
    Malaysian Institute of Architects
    Master Builders Association
    Ministry of Housing and Local Government (National Housing Departrnent(
    Ministry of Works and Utilities (Public works Department(
    University of Malaya

    The Technical Committee on Plastic Products (Constructionl which prepared this Malaysian Standard consists of the following representatives:
    Dr. Tee Tiam hog (Chairman(

    university of Malaya

    Encik Raymond Ng

    Federation of Plastics Manufacturers


    Dulon Industries (Ml Sdn. Bhd.

    Encik Richard Khong Hol Mun

    National Chambers of Commerce and Industry of Malaysia

    lr. Hasnur Rabiain Ismail

    Public Works Department

    Ir, Hj. Idaham Othman Merican

    Sekisu, lMalaysia( Sdn, Bhd.

    En. Richard Toh

    Hume Plastics (Ml Sdn. Bhd.

    EncikAndrew H.L. Chin

    Pakat Industries Bhd.

    Encik S.W Leong

    Paling Industries Sdn. Bhd,

    Tuari Hj. Zainuddin Hj. Ahmad

    City Hall

    Encik P. Kasi

    Malaysian Institute of Architects

    Encik Low Kim Chuan/


    Dr. R.C.H. Hsia

    Lian Huat Seng Plastic Industries Sdn Bhd.

    Cik Mariani Mohd, ISecrelary(

    Standards and Industrial Research Institute of Malaysia

    MS 979: Part 1: 1985

    FOREWORD

    This Malaysian Standard was prepared by the Technical Committee on Plastic Products (Construction) under the
    authority of the Building and Civil Engineering Industry Standards Committee.

    This standard is based on British Standard BS 4660: 1973. Unplasticized PVC underground drain pipe and fittings.
    Requirements are specified for unplasticized PVC pipe and fittings for underground sewer intended to convey
    normal domestic effluents including surface water.

    Standards referred to in this standard are as follows:


    MS 29

    Coarse and fine aggregates from natural sources

    MS 30

    Method for sampling and test of mineral aggregates. sand and fillers

    MS 567

    Sampling procedures and tables for inspection by attributes

    MS 672

    Materials for rubber joint rings for water supply and drainage pipelines.

    MS

    Unplasticized PVC soil, waste and ventilating pipe, fittings and accessories (Under preparation)

    BS 1 53

    Stee( girder bridges

    BS 812

    Methods for sampling and testing of mineral aggregates, sands and fillers

    BS 882.

    Aggregates from natural sources for concrete

    BS 903

    Methods of testing vulcanized rubber


    Part A26 Determination of hardness

    BS 2494

    Materials for elastomeric joint rings for pipework and pipelines

    BS 2782

    Method of testing plastics

    BS 5252

    Frame work for colour co-ordination for building purposes

    BS 5556 Specification for general requirements for dimensions and pressure ratings for pipe of thermoplastics
    materials (metric series)

    You might also like