Create The Through Curves Surface

Create the Through Curves surface
1. Open ffm4_mc_fender.
2. Select all three strings, and then on the Analyze Shape toolbar,
click Show End Points
Notice there are two curves in the strings on the left and on the
right, but only one curve in the middle string. Take note of where
the curves in the front of both the left and right strings end.
3. Press the Escape key to deselect the curves.
4. On the Surface toolbar, click Through Curves
5. In the Through Curve dialog box, from the Alignment list, ensure
that Parameter is selected.
6. Select the Preserve Shape
check box.
7. In the Sections group, highlight Select Curve or Point.
8. On the Selection bar, from the Curve Rule list, select Tangent
Curves.
9. Select the curve as shown.
10.
Click the middle mouse button to advance.
11.
Select the second curve as shown.
12.
Click the middle mouse button to advance.
13.
Select the final curve as shown.
The preview of the surface is displayed
14.
Click OK.
Edit the surface alignment

1. In the view background, right-click and choose Rendering
StyleShaded.
2. Rotate the part and notice the irregularity of the shape.
3. On the Utility toolbar, click Edit Object Display
4. In the Class Selection dialog box, select the surface and click OK.
5. In the Edit Object Display dialog box, expand the Wireframe
Display group, and in the U and V boxes, type 10.
6. Click OK.
7. In the view background, right-click and choose Rendering
StyleStatic Wireframe.
Notice how Parameter alignment and Preserve Shape affect the

isoparameter lines of the surface.
8. Double-click the surface as shown.
The Through Curves dialog box is displayed.

9. In the Settings group, clear the Preserve Shape
check box.
10.
In the Alignment group, from the Alignment list, choose
Arc Length.
11.
In the view background, right-click and choose Rendering
StyleShaded with Edges.
12.
Click OK.
13.
Hide all the curves and sketches.
Tip
On the Utility toolbar, click Show and Hide
In the Hide column, click the Negative signs for

Sketches and Curves.
click Close.
Trim the solid body to the surface

1. In the Part Navigator, right-click Extrude (8) and choose Show.
The Trim Body dialog box appears.

2. On the Feature toolbar, click Trim Body
The Trim Body dialog box is displayed.

3. Select the solid body as shown.
4. Click the middle mouse button to advance to the Tool selection.
5. Select the Tool body as shown.
6. If your part does not appear as shown, click Reverse Direction.
7. Click OK.
8. On the Utility toolbar, click Show and Hide
In the Show and Hide dialog box, select the minus Hide
symbol for Curves, Sketches, and Sheet Bodies.
Click Close.
Create a shell feature

1. On the Feature toolbar, click Shell
2. On the Selection toolbar, from the Face Rule list, select Tangent
Faces.
3. Select the face as shown.
If you get an Alerts message, you can dismiss it.
4. Select the bottom face of the part.

The preview is displayed.
5. In the Thickness group, in the Thickness box, type 5.

6. Click OK.
Other features would be added to complete the part.

7. Close the part.
You completed the activity.
Use parameter alignment

1. Open ffm4_thru_curves_2.
You will use the four sets of sketch curves to define the shape of
the surface.
3. At the top of the Through Curves dialog box, click Reset
4. Make sure the following settings are selected:

o
In the Continuity group, First Section and Last Section =

G0 (Position).
In the Alignment group, Alignment = Parameter.
In the Output Surface Options group, Patch Type =

Multiple.
Construction = Normal.
Normal to End Sections = cleared
In the Alignment group, Preserve Shape = cleared.
Lofting Degree = 3.
.
.
2 of 3
Create a surface using By Points alignment

Select the section curves
1. In the Sections group of the dialog box, make sure Select Curve
or Point is active.
2. Expand the List so you can follow the selection of sections.

3. From the Curve Rule list select Feature Curves.
4. Select the first section at the left end, and click the middle
mouse button or click Add New Set
to complete the selection
of the first section.
5. Select the second section at the left end and click the middle
mouse button.
6. Select the third and then the fourth setions at their left ends and
click the middle mouse button after each selection.
Your vectors should display like this.

1 - Use parameter alignment
2 - Select the section curves
3 - Change to By Points alignment
Change to By Points alignment

1. In the Alignment group, from the Alignment list, select By
Points.
The alignment points for each section are calculated and they are
connected with lines.
The alignment is now better than with parameter alignment, but

you want to change the location of the points on sections 1 and 2
to provide a better transition shape for the upper angled face,
and how it washes out.
2. In the Alignment group, make sure Specify Point is active, drag

the four alignment points for the sections indicated above so it
looks something like the following, and then click OK.
Separate faces are formed between the sharp corners in this

part.
3. In the graphics window, double-click the surface you just
created.
In the Setting group, the Lofting Degree value is 3.
4. In the Lofting Degree box, type 1 and click OK.
5. Rotate the view so you are looking at the part as shown below.
Notice that the shape of the surface between section curves is

now linear (degree 1), and that there are new faces and edges at
the sections.
This would be more clear if the sketches were hidden.
6. Double-click the surface again and change the Lofting Degree to
2.
The shape of the surface is now better, and there are no
separate faces at the section curves.
7. Close all parts.

You completed the activity.
Create a solid body using Spline Points alignment

Open the part and start the feature
1. Open ffm2_thru_curves_4 and start the Modeling application if it
is not already active.
3. At the top of the Through Curves dialog box header, click Reset
.
When you use the Spline Points construction method, the section
curves must be single B-curves each with the same number of
defining points. In this part, the section curves meet these
conditions.
4. In the Alignment group, select the Preserve Shape
check box.
5. On the Selection bar, from the Curve Rule list, select Single
Curve.
6. In the Sections group of the dialog box, make sure Select Curve
or Point is active, select each of the sections (at the locations
indicated by the arrowheads) as shown in the graphic below
Note: Make sure to click the middle mouse button or click Add
New Set
after each selection.
Tip You can expand the list in the dialog box to better follow your
selection process.
7. Make sure the direction vectors point in the same direction,
otherwise your part will be twisted.
Specify the alignment

1. In the Output Surface Options group, from the Construction list,
select Spline Points.
2. In the Alignment group, clear the Preserve Shape
Notice that the edge (face division) disappeared.
check box.
3. Click OK to create the body.
If you were to create this feature using the Normal Construction,

you would have a higher number of faces and patches, making
the faces more complex. Using spline points simplifies the faces
while maintaining zero tolerance at the spline points.
4. Close all parts.

Create The Through Curves Surface

Uploaded by

Copyright:

Available Formats

Create The Through Curves Surface

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Create The Through Curves Surface

Uploaded by

Copyright:

Available Formats

Create the Through Curves surface

7. In the Sections group, highlight Select Curve or Point.

Click the middle mouse button to advance.

Select the second curve as shown.

Click the middle mouse button to advance.

Select the final curve as shown.

The preview of the surface is displayed

Edit the surface alignment

3. On the Utility toolbar, click Edit Object Display

Notice how Parameter alignment and Preserve Shape affect the

The Through Curves dialog box is displayed.

Hide all the curves and sketches.

On the Utility toolbar, click Show and Hide

In the Hide column, click the Negative signs for

Trim the solid body to the surface

The Trim Body dialog box appears.

The Trim Body dialog box is displayed.

4. Click the middle mouse button to advance to the Tool selection.

5. Select the Tool body as shown.

6. If your part does not appear as shown, click Reverse Direction.

Create a shell feature

If you get an Alerts message, you can dismiss it.

4. Select the bottom face of the part.

5. In the Thickness group, in the Thickness box, type 5.

Other features would be added to complete the part.

Use parameter alignment

3. At the top of the Through Curves dialog box, click Reset

4. Make sure the following settings are selected:

In the Continuity group, First Section and Last Section =

In the Alignment group, Alignment = Parameter.

In the Output Surface Options group, Patch Type =

Normal to End Sections = cleared

In the Alignment group, Preserve Shape = cleared.

Create a surface using By Points alignment

2. Expand the List so you can follow the selection of sections.

Change to By Points alignment

The alignment is now better than with parameter alignment, but

2. In the Alignment group, make sure Specify Point is active, drag

Separate faces are formed between the sharp corners in this

Notice that the shape of the surface between section curves is

7. Close all parts.

Create a solid body using Spline Points alignment

2. On the Surface toolbar, click Through Curves

Specify the alignment

3. Click OK to create the body.

If you were to create this feature using the Normal Construction,

You might also like