A Paper presentation on

REAL TIME IMAGE PROCESSING

APPLIED TO TRAFFIC
QUEUE DETECTION ALGORITHM

Prepared by

A.UMAMAHESWARARAO
Email-id:umamahesh1201@yahoo.com
&

RAMA KRISHNA
Email-id: @yahoo.com

Of Third IT,

SRI MITTAPALLI COLLEGE OF ENGINEERING

TUMMALAPALEM

ABSTRACT_____________________
This paper primarily aims at the new technique of video image
processing used to solve problems associated with the real-time road traffic control
systems. There is a growing demand for road traffic data of all kinds. Increasing
congestion problems and problems associated with existing detectors spawned an
interest in such new vehicle detection technologies. But the systems have difficulties
with congestion, shadows and lighting transitions.
Problem concerning any practical image processing application to road
traffic is the fact that real world images are to be processed in real time. Various
algorithms, mainly based on back ground techniques, have been developed for this
purposes since back ground based algorithms are very sensitive to ambient lighting
conditions, they have not yielded the expected results. So a real-time image tracking
approach using edged detection techniques was developed for detecting vehicles
under these trouble-posing conditions.
This paper will give a general overview of the image processing
technique used in analysis of video images, problems associated with it, methods of
vehicle detection and tracking, pre-processing techniques and the paper also
presents the real-time image processing technique used to measure traffic queue
parameters.

TABLE OF CONTENTS
(1) Introduction

(2) Signal & Image Processing applied to traffic

2.1

Digital Signal

2.2

Need for processing

2.3

Parameters measurable...

2.4

Image analysis system structure.

(3) Stages of image analysis

0

Pipeline preprocessing...

(4) Real-time image processing-Queue detection algorithm

0

Methods of vehicle detection and tracking...

(5) Motion detection operation...

(6) Motion detection flowchart...

(7) Vehicle detection algorithm

0

Left-limit selection program

(8) Threshold selection program

8.1

Threshold selection...

8.2

Traffic Movements at Junctions.

10

8.3

Results and Discussions...

11

(9) Conclusion

12

References .

13

INTRODUCTION _____________________

Digital processing is done with a digital computer or some special purpose

digital hardware

The word Digital implies that the information in the computer is represented
and sent by variables that taken limited number of discrete values.

increasing demand for road traffic data of all sorts

Variation of parameters in real-world traffic

Aimed to measure queue parameters accurately

Algorithm has two operations: vehicle detection and motion detection

Operations applied to profiles consisting sub-profiles to detect queue

Motion detection is based on applying a differencing technique on the

profiles of the images along the road

The vehicle detection is based on applying edge detection on these profiles

Digital Signal
Digital systems functions more reliable, because only tow states are used
(zeros and ones BINARY SYSTEM). The word signal is a function of independent
variables. The signal it self carries some kind of information available for
observation.
By processing we mean operating in some fashion on signal to extract some
useful information. In many cases the processing will be none destructive
TRANEFER MODE of the given data signal.
Signal processing will be done in many ways.
1.

Analog signal processing

2.

Digital signal processing

3.

Light(Optical)wave signal processing

4.

Radio frequency signal transmission

DIGITAL SIGNAL PROCESSING

Image processing applied to traffic

Need for processing of traffic data: Traffic surveillance and control, traffic management, road safety and
development of transport policy.

Traffic parameters measurable: Traffic volumes, Speed, Headways, Inter-vehicle gaps, Vehicle classification,
Origin and destination of traffic, Junction turning.

Image analysis system structure

CCTV
camera

RAM
64k bytes

ADC

Backing store
2 M-byte

16-bit
MiniComputer

(data bus)
DAC

monitor

Printer

Stages of image analysis: Image sensors used :

Improved video cameras: automatic gain control, low SNR

ADC Conversion: - Analog video signal received from video camera is

converted to digital/binary form for processing

Pre-processing:
High SNR of the camera output reduces the quantity of processing enormous
data flow.

To cope with this, two methods are proposed:

1. Analyze data in real time - uneconomical
2. Stores all data and analyses off-line at low speed.
Pipeline Preprocessing does this job

Stages in Pipeline Preprocessing:

(1) Spatial Averaging contiguous pixels are averaged (convolution)
(2) Subtraction of background scene from incoming picture.
(3) Threshold Large differences are true 1, small differences are false 0
(4) Data Compression reduces resulting data.
(5) Block buffering collects data into blocks.
(6) Tape Interface blocks are loaded onto a digital cassette recorder

Preprocessed picture is submitted to processor as 2-D array of numbers

Two jobs to be done:

Green light on: - determine no. of vehicles moving along particular lanes and their
classification by shape and size.
Red light on: - determine the backup length along with the possibility to track its
dynamics and classify vehicles in backup

Methods of vehicle detection :

Background frame differencing: -grey-value intensity reference image

Inter-frame differencing: -incoming frame itself becomes the background for

the following frame

Segmentation and classification: -Sub division of an image into its

constituent parts depending on the context

Queue Detection Algorithm

Approach described here is a spatial-domain technique to detect queue

- implemented in real-time using low-cost system
For this purpose two different algorithms have been used,
Motion detection operation, Vehicle detection operation

Motion detection is first as in this case vehicle detection mostly gives

positive result, while in reality, there may not be any queue at all.
Applying this scheme further reduces computation time.

1.

Motion detection operation: -

a) Differencing two consecutive frames.

b) Histogram of the key region parts of the frames is analyzed by comparing
with the threshold value.
c) Key region should be at least 3-pixel-wide profile of the image along the
road.
d) A median filtering operation is firstly applied to the key region (profile) of
each frame and one-pixel-wide profile is extracted.
e) Difference of two profiles is compared to detect for motion.

Note: The size of the profile is an important parameter.

Motion Detection Algorithm

Block diagram

frame 1

frame 2

L+2

L+2

Median Filter
Line profile 0

Line profile 1

Dif = profile 1 profile 0

No(motion)

Yes(motion)

Dif<T
h1

1.

Motion detection operation: -

f) Differencing two consecutive frames.

g) Histogram of the key region parts of the frames is analyzed by comparing
with the threshold value.
h) Key region should be at least 3-pixel-wide profile of the image along the
road.
i) A median filtering operation is firstly applied to the key region (profile) of
each frame and one-pixel-wide profile is extracted.
j) Difference of two profiles is compared to detect for motion.
k) When there is motion, the differences of the profiles are larger than the case
when there is no motion. The motion can be detected by selecting a threshold
value.

Note: The size of the profile is an important parameter.

Vehicle detection algorithm: -

o Following the application of the motion detection operation, a vehicle

detection operation is applied on the profile of the unprocessed image.
o To implement the algorithm in real time, two strategies are often applied: key
region processing and simple algorithms.
o Most of the vehicle detection algorithms developed so far are based on a
background differencing technique, which is sensitive to variations of
ambient lighting.
o The method used here is based on applying edge detector operators to a
profile of the image Edges are less sensitive to the variation of ambient
lighting and are used in full frame applications (detection).
o Edge detectors consisting of separable medium filtering and morphological
operators, SMED (Separable Morphological Edge Detector) are applied to the
key regions of the image. (The SMED approach is applied (f) to each subprofile of the image and the histogram of each sub-profile is processed by
selecting Dynamic left-limit value and a threshold value to detect vehicles.
o SMED

has lower computational requirement while having comparable

performance to other morphological operators

o SMED can detect edges at different angles, while other morphological
operators are unable to detect all kinds of edges.

Left-limit selection program:

This program selects a grey value from the histogram of the window, where
there are approx. zero edge points above this grey value.

When the window contains an object, the left-limit of the histogram shifts
towards the maximum grey value, otherwise it shifts towards the origin.

This process is repeated for a large no. of frames(100),and the minimum of

the left-limit of these frames is selected as the left-limit for the next frame

Threshold selection program:-

The no. of edge points greater than the left limit grey value of each window is
extracted for a large no. of frames (200) to get enough parameters below and
above a proper threshold value.
This nos. are used to create a histogram where its horizontal and vertical
axes correspond to the no. of edge points greater than left limit and the
frequency of repetition of these numbers for a period of operation of the
algorithm (200 frames).
This histogram is smoothed using a median filter and we expect to get two
peaks in the resulted diagram, one peak related to the frames passing a
vehicle and the other related to the frames without vehicles for that window.
However, as it can be seen in the figure given below, there are other number
of edge points (32-40) between peaks 20 & 60, which are related to those
vehicles in each profile. We use statistical approach based on selecting a point
on the horizontal axis, where the sum of the entropy of the points above and
below this point is maximum. This point is selected as the threshold value for
the next period.

Traffic movements at junctions (TMJ):

Measuring traffic movements of vehicles at junctions such as number of
vehicles turning in a different direction (left, right, and straight) is very
important for the analysis of cross-section traffic conditions and adjusting
traffic lights.
Previous research work for the TMJ parameter is based on a full-frame
approach, which requires more computing power and, thus, is not suitable
for real-time applications.

We use a method based on counting vehicles at

the key regions of the junctions by using the vehicle-detection method.

The first step to measure the TMJ parameters using the key region method is
to cover the boundary of the junction by a polygon in such a way that all the

entry and exit paths of the junction cross the polygon. However, the polygon
should not cover the pedestrian marked lines. This step is shown in the figure
given below.
The second step of the algorithm is to define a minimum numbers of key
regions inside the boundary of the polygon, covering the junction.
These key regions are used for detecting vehicles entering and exiting the
junction, based on first vehicle in first-vehicle-out logic.
Following the application of the vehicle detection on each profile, a status
vector is created for each window in each frame.
If a vehicle is detected in a window, a one is inserted on its corresponding
status vector; otherwise, a Zero is inserted.
Now by analyzing the status vector of each window, the TMJ parameters are
calculated for each path of the junction.

Polygon Covered
Junction

Pedestrian line mark

Results and Discussions:

The main queue parameters we were interested in identifying were the length
of the queue, the period of occurrence and the slope of the occurrence of the
queue behind the traffic lights.

To implement the algorithm in real-time, it was decided that the vehicle

detection operation should only be used in a sub-profile where we expect the
queue will be extended. The procedure

Level>Th

Level>Th

N
motion detection

Q
U
E
U
E

D
E
T
E
C
T
I
O
N

Level>Th

Level>Th

vehicle detection

E
D
G
E
D
E
T
E
C
T
I
O
N

Conclusions

Algorithm measuring basic queue parameters such as period of occurrence

between queues, the length and slope of occurrence has been discussed.
The algorithm uses a recent technique by applying simple but effective operations.
In order to reduce computation time motion detection operation is applied on all
sub-profiles while the vehicle detection operation is only used when it is necessary.
The vehicle detection operation is a less sensitive edge-based technique. The
threshold selection is done dynamically to reduce the effects of variations of lighting.
The measurement algorithm has been applied to traffic scenes with different
lighting conditions.

 Queue length measurement showed 95% accuracy at maximum. Error is due to

objects located far from camera and can be reduced to some extent by reducing the
size of the sub-profiles.

BIBLIOGRAPHY

Digital Image Processing by Rafael C.Gonzalez and Richard E.Woods.

Hoose. N: Computer Image Processing in Traffic Engineering.

Rourke, A., and Bell, M.G.H.: Queue detection and congestion monitoring
using mage processing, Traffic Engg. And Control.

Traffic Queue Length Measurement Using an Image Processing Sensor by

Masakatsu Higashikobo, Toshio Hinenoya and Kouhei Takeouchi.

A Real-time Computer Vision System for Vehicle Tracking and Traffic

Surveillance by Benjamin Coifman (corresponding author).

A Real-time Computer Vision System for Measuring Traffic Parameters by

David Beymer, Philip McLauchlan, Benn Coifman and Jitendra Malik.