R07 Set No. 2
R07 Set No. 2
R07 Set No. 2
R07
Set No. 2
[8+8]
[8+8]
3. Explain the components of solid rockets and for which applications the rockets are
used.
[16]
4. Describe various types of injectors in liquid rockets, what are salient injector flow
characteristics?
[16]
5. Suppose you are planning to launch a pay load on a long journey to a planet, what
type of light weight propulsion system would you suggest for the payload for its
course correction? Explain the propulsion system.
[16]
6. Describe the bleed burn cycle for employing thrurst augmentation.
[16]
7. A ramjet engine operates at M = 1.5 at an altitude of 6.5 km. The diameter of the
inlet diffuser at entry is 0.5 m and the stagnation temperature at the nozzle entry
is 1600 K. The calorific value of the fuel used is 40 MJkg1 . The properties of the
-1
combustion gases are same as those of air, i.e. = 1.4, R = 287 J kg1 K . The
velocity of air at the diffuser exit is negligible. Assuming, Assuming the efficiency of diffuser
combutionchamber and nozzle as 0.9, 0.98 and 0.96 respectively.
the following:
[16]
1
R07
Set No. 2
8. Write short notes on the following aspects related to turbine blade failure:
(a) Gerbers Curves
(b) Creep curves.
[8+8]
?????
R07
Set No. 4
[8+8]
3. (a) Explain the salient features of a solid rocket motor with the help of a suitable
diagram.
(b) Explain the following with respect to the solid propellant rocket motor:
i. Relationship between the burning rate and chamber pressure.
ii. Relationship between the burning rate and temperature.
[8+4+4]
R07
Set No. 4
[4+4+4+4]
8. What is the importance of thrust vector contral in figher aircraft. Discuss the methods
emplyoed.
[16]
?????
R07
Set No. 1
3. Define and derive the relationship for gross thrust coefficient of a ramjet engine.
Explain the behavioural characteristics of gross thrust coefficient with the related
parameters with the help of plots for a fixed geometry ramjet engine.
[16]
4. Mention the various advanced propulsion systems and describe the principle of
electric propulsion.
[16]
5. (a) Differentiate between total impulse and specific impulse.
(b) Describe the over expanded and under expanded nozzle.
[8+8]
6. A multi-stage gas turbine is to be designed with impulse stages, and is to be operated with an inlet pressure and temperature of 6 bar and 900 K respectively and
an outlet pressure of 1 bar. The isentropic efficiency of the turbine is 85%. All
the stages are required to have a nozzle outlet angle of 150 . Also, they have equal
outlet & inlet blade angles and equal inlet & outlet nozzle angles. Mean blade speed
is equal to 250ms1 . Assuming Cp = 1.15 kJkg1 s1 and = 1.333, estimate the
number of stages required.
[16]
7. Explain the engine cycle for turbo pump feed liquid propellants.
[16]
8. Explain the function of two nozzles employed for supersonic aircraft concorde.[16]
?????
R07
Set No. 3
3. (a) Define Effective jet Mach number for a ramjet engine and derive the relationship for it.
(b) Write a detailed note on variable geometry ramjet engine.
[8+8]
4. In a single-stage impulse turbine the nozzle discharges the fluid on to the blades
at an angle of 250 to the plane of rotation and the fluid leaves the blades with an
absolute velocity of 300ms1 at an angle of 1200 to the direction of motion of the
blades. If the blades have an equal inlet and outlet angles and there is no axial
thrust, estimate the blade angle, power produced per kgs1 of the fluid.
[16]
5. What is the advantage of using cryogenic propellants in liquid rockets? Mention
the typical cryogenic propellants and their applications. What are the precautions
taken while handling them?
[16]
[16]
7. Discuss in detail about the quasi-steady and periodic fluctuating type of stresses
acting on a conventional turbine blade, which could lead to crack initiation and
eventual failure of the blade.
[16]
8. Write notes on the following with respect to the solid propellant rocket motor:
(a) Rocket motor case
(b) Igniters.
[8+8]
?????