Xerox Phaser 6110 - Service Manual

Publication Information for Xerox,
Phaser 6110
Service Documentation
Product : Xerox Phaser 6110 Service Documentation
Title: Xerox Phaser 6110 Service Documentation
Part number: 701P28450
January 29, 2007
Precautions
In order to prevent accidents and to prevent damage to the equipment please read the precautions listed
below carefully before servicing the printer and follow them closely.
Safety Warning
(1) Only to be serviced by appropriately qualified service engineers.
High voltages and lasers inside this product are dangerous. This printer should only be serviced by a suitably
trained and qualified service engineer.
(2) Use only Xerox replacement parts
There are no user serviceable parts inside the printer. Do not make any unauthorized changes or
additions to the printer, these could cause the printer to malfunction and create electric shock or fire haz-ards.
(3) Laser Safety Statement
The Printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J for
Class 1(1) laser products, and elsewhere, it is certified as a Class I laser product
con-forming to the requirements of IEC 825. Class I laser products are not considered to be hazardous. The
laser system and printer are designed so there is never any human access to laser radiation above a Class I
level during normal operation, user maintenance, or prescribed service condition.
Warning >> Never operate or service the printer with the protective cover removed from Laser/Scanner assembly. The
reflected beam, although invisible, can damage your eyes. When using this product, these basic safety
pre-cautions should always be followed to reduce risk of fire, electric shock, and injury to persons.
CAUTION - INVISIBLE LASER RADIATION

WHEN THIS COVER OPEN.
DO NOT OPEN THIS COVER.
VORSICHT - UNSICHTBARE LASERSTRAHLUNG,
WENN ABDECKUNG GEFFNET.
NICHT DEM STRAHL AUSSETZEN.
ATTENTION - RAYONNEMENT LASER INVISIBLE EN CAS
DOUVERTURE. EXPOSITION DANGEREUSE
AU FAISCEAU.
ATTENZIONE - RADIAZIONE LASER INVISIBILE IN CASO DI
APERTURA. EVITARE LESPOSIZIONE AL
FASCIO.
PRECAUCION - RADIACION LASER IVISIBLE CUANDO SE ABRE.
EVITAR EXPONERSE AL RAYO.
ADVARSEL. - USYNLIG LASERSTRLNING VED BNING, NR
SIKKERHEDSBRYDERE ER UDE AF FUNKTION.
UNDG UDSAETTELSE FOR STRLNING.
ADVARSEL. - USYNLIG LASERSTRLNING NR DEKSEL
PNES. STIRR IKKE INN I STRLEN.
UNNG EKSPONERING FOR STRLEN.
VARNING - OSYNLIG LASERSTRLNING NR DENNA DEL
R PPNAD OCH SPRREN R URKOPPLAD.
BETRAKTA EJ STRLEN. STRLEN R FARLIG.
VARO! - AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTIINA NKYMTTMLLE LASERSTEILYLLE L KATSO STEESEEN.
Caution for safety

Toxic material
This product contains toxic materials that could cause illness if ingested.
(1) Please keep toner cartridges away from children. The toner powder contained in the toner cartridge may be harmful
and if swallowed you should contact a doctor.
Electric Shock and Fire Safety Precautions

Failure to follow the following instructions could cause electric shock or potentially cause a fire.
(1) Use only the correct voltage, failure to do so could damage the printer and potentially cause a fire or electric
shock.
(2) Use only the power cable supplied with the printer. Use of an incorrectly specified cable could cause the cable
to overheat and potentially cause a fire.
(3) Do not overload the power socket, this could lead to overheating of the cables inside the wall and could lead to
a fire.
(4) Do not allow water or other liquids to spill into the printer, this can cause electric shock. Do not allow paper
clips, pins or other foreign objects to fall into the printer these could cause a short circuit leading to an electric
shock or fire hazard..
(5) Never touch the plugs on either end of the power cable with wet hands, this can cause electric shock. When
servicing the printer remove the power plug from the wall socket.
(6) Use caution when inserting or removing the power connector. The power connector must be inserted completely otherwise a poor contact could cause overheating possibly leading to a fire. When removing the power
connector grip it firmly and pull.
(7) Take care of the power cable. Do not allow it to become twisted, bent sharply round corners or other wise
damaged. Do not place objects on top of the power cable. If the power cable is damaged it could overheat and
cause a fire or exposed cables could cause an electric shock. Replace a damaged power cable immediately,
do not reuse or repair the damaged cable. Some chemicals can attack the coating on the power cable,
weakening the cover or exposing cables causing fire and shock risks.
(8) Ensure that the power sockets and plugs are not cracked or broken in any way. Any such defects should be
repaired immediately. Take care not to cut or damage the power cable or plugs when moving the machine.
(9) Use caution during thunder or lightening storms. Xerox recommend that this machine be disconnected from
the power source when such weather conditions are expected. Do not touch the machine or the power cord if it
is still connected to the wall socket in these weather conditions.
(10) Avoid damp or dusty areas, install the printer in a clean well ventilated location. Do not position the machine
near a humidifier. Damp and dust build up inside the machine can lead to overheating and cause a fire.
(11) Do not position the printer in direct sunlight. This will cause the temperature inside the printer to rise possibly
leading to the printer failing to work properly and in extreme conditions could lead to a fire.
(12) Do not insert any metal objects into the machine through the ventilator fan or other part of the casing, it could
make contact with a high voltage conductor inside the machine and cause an electric shock.
Handling Precautions
The following instructions are for your own personal safety, to avoid injury and so as not to damage the printer
(1) Ensure the printer is installed on a level surface, capable of supporting its weight. Failure to do so could cause
the printer to tip or fall.
(2) The printer contains many rollers, gears and fans. Take great care to ensure that you do not catch your fingers,
hair or clothing in any of these rotating devices.
(3) Do not place any small metal objects, containers of water, chemicals or other liquids close to the printer which if
spilled could get into the machine and cause damage or a shock or fire hazard.
(4) Do not install the machine in areas with high dust or moisture levels, beside on open window or close to a
humidifier or heater. Damage could be caused to the printer in such areas.
(5) Do not place candles, burning cigarettes, etc on the printer, These could cause a fire.
Assembly / Disassembly Precautions

Replace parts carefully, always use approved parts. Take care to note the exact location of parts and also
cable routing before dismantling any part of the machine. Ensure all parts and cables are replaced correctly.
Please carry out the following procedures before dismantling the printer or replacing any parts.
(1) Check the contents of the machine memory and make a note of any user settings. These will be erased if the
mainboard or network card is replaced.
(2) Ensure that power is disconnected before servicing or replacing any electrical parts.
(3) Disconnect printer interface cables and power cables.
(4) Only use approved spare parts. Ensure that part number, product name, any voltage, current or temperature
rating are correct.
(5) When removing or re-fitting any parts do not use excessive force, especially when fitting screws into plastic.
(6) Take care not to drop any small parts into the machine.
(7) Handling of the OPC Drum
- The OPC Drum can be irreparably damaged if it exposed to light.
Take care not to expose the OPC Drum either to direct sunlight or to fluorescent or incandescent room
lighting. Exposure for as little as 5 mins can damage the surfaces photoconductive properties and will result
in print quality degradation. Take extra care when servicing the printer. Remove the OPC Drum and store it in
a black bag or other lightproof container. Take care when working with the covers(especially the top cover)
open as light is admitted to the OPC area and can damage the OPC Drum.
- Take care not to scratch the green surface of OPC Drum Unit.
If the green surface of the Drum Cartridge is scratched or touched the print quality will be compromised.
1-3
Disregarding this warning may cause bodily injury

(1) Be careful with the high temperature part.
The fuser unit works at a high temperature. Use caution when working on the printer. Wait for the fuser to cool
down before disassembly.
(2) Do not put finger or hair into the rotating parts.
When operating a printer, do not put hand or hair into the rotating parts (Paper feeding entrance, motor, fan,
etc.). If do, you can get harm.
(3) When you move the printer.
This printer weighs 19.95kg including toner cartridge and cassette. Use safe lifting and handling techniques.
Use the lifting handles located on each side of the machine. Back injury could be caused if you do not lift carefully.
(4) Ensure the printer is installed safely.
The printer weighs 19.95Kg, ensure the printer is installed on a level surface, capable of supporting its weight.
Failure to do so could cause the printer to tip or fall possibly causing personal injury or damaging the printer.
(5) Do not install the printer on a sloping or unstable surface. After installation, double check that the printer is stable.
Section 1 Service Call Procedures
There is a smell, or smoke, or the printer is hot. NOTE: the top cover, above
the Fuser, is normally very warm to the touch when printer is ready.
No
Yes
Remove the Fuser (5.4.2) and check it for signs of overheating such as
discoloration, deformed frames, or a thermostat with high electrical
resistance. Remove the Covers (5.4.1). Check the PWBs and wiring for
signs of overheating. Check the drives for signs of damage (5.4.7).
Replace or repair any part as required.
Switch on the power. The LED panel indicates ready.
Yes No
Remove the Covers (5.4.1). Go to the Block Diagram, lower right corner,
and check input power, switch, SMPS, and Main PWB power distribution
voltages.
Refer to the Control Panel wiring diagram (Section 7, Level 2 Block
Schematic Diagram).
Refer to Control Panel LEDs (Section 10 Product Technical Overview).
Print a Demonstration Print (Section 6 General Procedures). The
Demonstration Print is output.
Yes No
Go to 7.3 Solving General Printing Problems (Section 3 User Declared
Errors)
The Demonstration Print image quality is good.
Yes No
Go to Image Quality Problems (Section 3 User Declared Errors)
There is still a problem with the printer.
No
Yes
Go to Section 3 User Declared Errors and attempt to find a solution.
Verify that Routine Maintenance is complete (Section 1, 5.2 Parts for
Maintenance and Repair).
Ensure Printer is ready for customer service (clean covers)
Place Demonstration Print in output tray.
Disassembly and Reassembly
Parts for Maintenance and Repair

Replacement interval for parts with a limited life
Some of the parts in this printer have a limited life, shorter than that of the whole machine. These parts
must be replaced periodically.
The table below shows the interval at which these parts should be replaced.
The table shows the life of each part, and is measured when using A4 paper. When servicing a machine
always check the status of these parts using the control panel and ensure that parts are replaced at the
appropriate times otherwise a general degradation in print quality will occur.
COMPONENT
REPLACEMENT CYCLE
REMARK
Toner Cartridge (Black)
intial (1,500 pages@5% coverage)

replacement (2,000 pages@5% coverage)
User replace
Toner Cartridge (Color: C/M/Y)
intial (700 pages@5% coverage)

User replace
Waste toner container
5K image or 1.25K pages

(Full color 5% image)
T2 Roller
100K pages
Imaging Unit
20K pages (Black)

12.5K pages (Color)
ITB Unit(Image Transfer Unit)
Black : (60K pages@5% coverage)

Color : (15K pages@5% coverage)
Pick-Up Roller
100,000 pages
- MP Pick-Up Roller,
- Cassette Tray1 Pick-Up Roller
Engineer
Fuser Unit
100,000 pages (B/W) Color(50,000 pages)
User replace
User replace
User replaceCo,
The life span of each of these parts is stored in memory. The amount of each 'life' used can be checked at
any time using the control panel.
When a part is replaced it is necessary to reset the 'life used' that is stored in memory.
* How to initialize a the value of part's life span:
From the control panel, select the following items in order:
Menu-Setup - Maintenance - Check other - (Select a desired part) - Reset
Service Manual
Section 2 Machine Declared Faults
Alignment and Adjustmens
Error Message
When the printer experiences an error, the control panel will indicate an error message with the indicator
lights. Find the light pattern below that matches the printer light pattern and follow the solutions to clear the error.
LED status legend
LED pattern
Possible Problem and Solution

The blinking toner cartridge is low. Order a new toner cartridge. You can temporarily improve print quality by redistributing the toner.
The lighting toner cartridge is empty.

Remove the old toner cartridge and install a new one.
The blinking toner cartridge is totally exhausted. Remove the old toner cartridge
and install a new one.
The blinking toner cartridge is wrong. Only install a Xerox toner
cartridge, designed for your printer.
A paper jam has occurred. To solve the problem.

The front cover is open. Close the front cover.
There is no paper in the tray. Load paper in the tray.
The waste toner container is open or full. Check the container.
Your system has some problems. If this problem occurs, contact your service
representative.
Service Manual
Troubleshooting
JAM 0
Service Manual
Troubleshooting
JAM 1
Multi-Feeding
No Fuser drive due to overheated gear(s)
Service Manual
Troubleshooting
Paper Empty
Cover Open
Defective motor operation
Service Manual
Section 3 User Declared Faults
Troubleshooting
Solving Print Quality Problems

Dirt inside of the printer or improper paper loading may reduce print quality. See the table below to troubleshoot
problems.
Problem
Light or faded print
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Toner specks
Solution
If a vertical white streak or faded area appears on the page:
The toner supply is low. You may be able to temporarily extend the toner cartridge life.
If this does not improve print quality, install a new toner cartridge.
The paper may not meet paper specifications (for example, the paper is too moist or too
rough).
A combination of faded or smeared defects may indicate that the printer needs cleaning.
The paper may not meet specifications (for example, the paper is too moist or too rough).
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Dropouts
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Vertical lines
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
If generally rounded, faded areas occur randomly on the page:

A single sheet of paper may be defective. Try reprinting the job.
The moisture content of the paper is uneven or the paper has moist spots on its surface. Try a different brand of paper.
The paper lot is bad. The manufacturing process can cause some areas to reject toner.
Try a different kind or brand of paper.
The toner cartridge may be defective. See "Vertical repetitive defects" on the next page.
If these steps do not correct the problems, contact a service representative.
If black vertical streaks appear on the page:

A imaging unit has probably been scratched.
Remove the imaging unit and install a new one.
If white vertical lines appear on the page:
Clean the inside of the printer. If you still have the same problems, replace the imaging
unit with a new one.
Service Manual
Troubleshooting
Problem
Color or Black
background
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Toner smear
Vertical repetitive
defects
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Background scatter
A
Misformed
characters
Service Manual
Solution
If the amount of background shading becomes unacceptable, the procedures below may
fix the problem.
Change to lighter weight paper.
heck the printer's environment; very dry (low humidity) or high humidity (higher than
80% RH) conditions can increase the amount of background shading.
Remove one of the old toner cartridges and install a new one.
Clean the inside of the printer.

Check the paper type and quality.
Remove the imaging unit and install a new one.
If marks repeatedly appear on the printed side of the page at even intervals:
Clean the inside of the printer. After cleaning the inside of the printer, if you still have the
same problems, install a new toner cartridge of the problem color.
Parts of the printer may have toner on them. If the defects occur on the back of the
page, the problem will likely correct itself after a few more pages.
The fusing assembly may be damaged. Contact a service representative.
Background scatter results from bits of toner distributed on the printed page.
The paper may be too damp. Try printing with a different batch of paper. Do not open
packages of paper until necessary so that the paper does not absorb too much moisture.
If background scatter occurs on an envelope, change the printing layout to avoid printing over areas that have overlapping seams on the reverse side. Printing on seams can
cause problems.
If background scatter covers the entire surface area of a printed page, adjust the print
resolution through your software application or via the printer properties window.
If characters are improperly formed and producing hollowed images, the paper stock
may be too slick. Try a different paper.
If characters are improperly formed and producing a wavy effect, the printer may need
service. Verify that it also occurs on a demo page.
Troubleshooting
Problem
Page skew
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Solution
Ensure that the paper is loaded properly.
Ensure that the paper or other material is loaded correctly and the guides are not too
tight or too loose against the paper stack.
Curl or wave

Check the paper type and quality. Both high temperature and high humidity can cause
paper curl.
Turn the stack of paper over in the tray. Also try rotating the paper 180 in the tray.
Wrinkles or creases

Turn the stack of paper over in the paper tray. Also try rotating the paper 180 in the
tray.
Back of printouts
aredirty
Check for leaking toner. Clean the inside of the printer.
Solid Color or
Black pages
The toner cartridge may not be installed properly.

Remove the toner cartridge and reinsert.
The toner cartridge may be defective and need replacing. Install a new toner cartridge.
The printer may require repair. Contact a service representative.
Service Manual
Troubleshooting
Problem
Loose toner
Character Voids
A
Horizontal stripes
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Curl
Service Manual
Solution
Clean the inside of the printer.
Install a new toner cartridge.
If the problem persists, the printer may require repair. Contact a service representative.
Character voids are white areas within characters that should be solid black:
You may be printing on the wrong surface of the paper. Remove the paper and turn it
over.
The paper may not meet paper specifications.
If horizontally aligned color or black streaks or smears appear:

A toner cartridge may be installed improperly.
Remove the toner cartridge and reinsert.
A toner cartridge may be defective. Install a new toner cartridge.
If the problem persists, the printer may require repair. Contact a service representative.
If the printed paper is curled or paper does not feed into the printer:
Turn the stack of paper over in the paper tray. Also try rotating the paper 180 in the
tray.
Troubleshooting
Major Problems Trouble shooting

Vertical Line and Band
Vertical White Line
Service Manual
Troubleshooting
Light Image
Dark Image or black
Service Manual
Troubleshooting
Background
Service Manual
Troubleshooting
Major Problems Trouble shooting

Vertical Line and Band
Vertical White Line
Service Manual
Troubleshooting
Light Image
Dark Image or black
Service Manual
Troubleshooting
Background
JAM 0
Service Manual
Periodic Defective Image

If an image defects appears at regular intervals on the printed-paper, it is due to a faulty or damaged roller.
Refer to the table below and check the condition of the appropriate roller.
No
Roller
Period
Phenomenon
OPC Drum
188.5 mm
White and Black Spots
Charge Roller
37.7mm
Black Spot and line and Periodic Band
Supply Roller
47.5mm
Periodic Band by little difference of density
Developing Roller
26.0mm
White Spot, Horizontal black band
1 st Transfer Roller
32.7mm
Ghost, Damaged Image by abnormal tranfer
2 nd Transfer Roller
57.5mm
Ghost, Damaged Image by abnormal tranfer
Heat Roller
86.6mm
Black Spots or Vertical Black Band
Pressure Roller
86.6mm
Background
Service Manual
Troubleshooting
Solving General Printing Problems

For problems with the operation of your printer, refer to the table for suggested solutions.
Service Manual
Troubleshooting
Service Manual
Troubleshooting
Service Manual
Troubleshooting
Service Manual
Troubleshooting
Common Windows Problems

Problem
"File in Use" message appears
during installation.
"Error Writing to LPTx" message
appears.
Possible Cause and Solution

Exit all software applications. Remove all software from the StartUp Group,
then restart Windows. Reinstall the printer driver.
Ensure that all cables are connected correctly and the printer is on.
If bi-directional communication is not turned on in the driver, it will also
cause this message.
"General Protection Fault",

"Exception OE", "Spool32", or
"Illegal Operation" messages
appear.
Close all other applications, reboot Windows and try printing again.
"Fail To Print", "A printer timeout

error occurred." messages appear.
These messages may appear during printing. Just keep waiting until the
printer finishes printing. If the message appears in standby mode or after
printing has been completed, check the connection and/or whether an error
has occurred.
NOTE: Refer to the Microsoft Windows 98/Me/NT 4.0/2000/2003/XP User's Guide that came with your PC for further
information on Windows error messages.
Common Macintosh Problems

Problem
The printer does not print a

document from Acrobat Reader.
You should change the Print Method option to Print as Image when you print
from Acrobat Reader.
The document has printed, but the

print job has not disappeared from
the spooler in Mac OS 10.3.2.
Update your Mac OS to OS 10.3.3 or higher.
Service Manual
Troubleshooting
Common Linux Problems

Problem
I can't change settings in the

configuration tool.
You need to have administrator privileges to be able to change global

settings.
I am using the KDE desktop but

the configuration tool and LLPR
won't start.
You may not have the GTK libraries installed. These usually come with most
Linux distributions, but you may have to install them manually. Refer to your
distribution's installation manual for more details about installing additional
packages.
I just installed this package but

can't find entries in the KDE/
Gnome menus.
Some versions of the KDE or GNOME desktop environments may require

that you restart your session for the changes to take effect.
I get a "Some options are not

selected" error message while
editing the printer settings.
Some printers have conflicting settings, meaning that some settings for two
options can't be selected at the same time. When you change a setting and
the Printer Package detects such a conflict, the conflicting option is changed
to a "No Choice" value. You have to choose an option that does not conflict
before being able to submit the changes.
I can't make a printer the system

default.
In some conditions, it may not be possible to change the default queue. This
happens with some variants of LPRng, especially on recent RedHat systems
that use the "printconf" database of queues.
When using printconf, the /etc./printcap file is automatically refreshed from
the database of printers managed by the system (usually through the "printtool" command), and the queues in /etc./printcap.local are appended to the
resulting file. The default queue in LPRng is defined as the first queue in
/etc./printcap, and therefore it is not possible for the Linux Printer Package to
change the default when some queues have otherwise been defined using
printtool.
LPD systems identify the default queue as the one named "lp". Thus, if there
is already a queue by this name, and if it doesn't have an alias, then you
won't be able to change the default. To work around this, you can either
delete the queue or rename it by manually editing the /etc./printcap file.
The N-up setting does not work

correctly for some of my
documents.
The N-up feature is achieved through post-processing of the PostScript data

that is sent to the printing system. However, such post-processing can
only be adequately achieved if the PostScript data conforms to the Adobe
Document Structing Conventions. Problems may arise when using N-up
and other features that rely on post-processing if the document being printed
isn't compliant.
I am using BSD lpr (Slackware,

Debian, older distributions) and
some options chosen in LLPR
don't seem to take effect.
Legacy BSD lpr systems have a hard limitation on the length of the option
string that can be passed to the printing system. As such, if you selected a
number of different options, you may have exceeded the length of the
options and some of your choices won't be passed to the programs
responsible for implementing them. Try to select fewer options that deviate
from the defaults, to save on memory usage.
Service Manual
Troubleshooting
Problem
I am trying to print a document in

Landscape mode, but it prints
rotated and cropped.
Most Unix applications that offer a Landscape orientation option in their printing options will generate correct PostScript code that should be printed as is.
In that case, you need to make sure that you leave the LLPR option set to its
default Portrait setting, to avoid unwanted rotations of the page that would
result in cropped output.
Some pages come out all white

(nothing is printed), and I am using
CUPS.
If the data being sent is in Encapsulated PostScript (EPS) format, some earlier versions of CUPS (1.1.10 and before) have a bug preventing them from
being processed correctly. When going through LLPR to print, the Printer
Package will work around this issue by converting the data to regular
PostScript.
However, if your application bypasses LLPR and feeds EPS data to CUPS,
the document may not print correctly.
I can't print to an SMB (Windows)

printer.
To be able to configure and use SMB-shared printers (such as printers

shared on a Windows printer), you need to have a correct installation of the
SAMBA package that enables that feature. The "smbclient" command should
be available and usable on your system.
My application seems to be frozen

while LLPR is running.
Most Unix applications will expect a command like the regular "lpr" command
to be non-interactive and thus return immediately. Since LLPR is waiting
for user input before passing the job on to the print spooler, very often the
application will wait for the process to return, and thus will appear to be
frozen (its windows won't refresh). This is normal and the application should
resume functioning correctly after the user exits LLPR.
How do I specify the IP address of

my SMB server?
It can be specified in the "Add Printer" dialogue of the configuration tool, if

you don't use the CUPS printing system. Unfortunately, CUPS currently
doesn't allow you to specify the IP address of SMB printers, so you will have
to be able to browse the resource with SAMBA in order to be able to print.
Some documents come out as

white pages when printing.
Some versions of CUPS, especially those shipped with Mandrake Linux

before the 8.1 release, have some known bugs when processing PostScript
output from some applications. Try upgrading to the latest version of CUPS
(at least 1.1.14). Some RPM packages for the most popular distributions are
provided as a convenience with this Linux Printing Package.
I have CUPS and some options

(such as N-up) seem to be always
enabled even though I don't
choose them in LLPR.
There may be some local options defined in your ~/ .lpoptions file, which are
manipulated by the lpoptions command. These options are always used
if not overridden by LLPR settings. To get rid of all options for a printer, run
the following command, replacing "printer" with the name of the queue:
lpoptions -x printer
I configured a printer to print to a

file, but I get "Permission denied"
errors.
Most printing systems will not run as the super-user but as a special user
(usually "lp"). Therefore, make sure that the file you have chosen to print to is
accessible to the user owning the spooler daemon.
Service Manual
Troubleshooting
Problem
On my PCL (or GDI) printer, I

sometimes get error messages
printing instead of my document.
Unfortunately, some Unix applications may generate non-compliant

PostScript output that may not be supported by Ghostscript, or even the
printer itself in PostScript mode. You can try to capture the output to a file and
view the results with Ghostscript (gv or ghostview will allow you to do so
interactively) and see if you get error messages.
However, since the application is probably at fault, contact your software vendor to inform them of the issue.
Some color images come out all

black.
This is a known bug in Ghostscript (until GNU Ghostscript version 7.05)

when the base color space of the document is indexed color space and it is
converted through CIE color space. Because Postscript uses CIE color
space for Color Matching System, you should upgrade Ghostscript on your
system to at least GNU Ghostscript version 7.06 or later. You can find recent
Ghostscript versions at www.ghostscript.com.
Service Manual
LED Diagnostics:
Remove the Covers (5.4.1). Go to the Block Diagram, lower right corner, and
check input power, switch, SMPS, and Main PWB power distribution voltages.
Refer to the Control Panel wiring diagram (Section 7, Level 2 Block Schematic
Diagram). Refer to Control Panel LEDs (Section 10 Product Technical Overview).
LED Operation:
Go to next page.
LED Function
There are six LEDs present. Status led indicate the error/online status of the printer in idle mode. In error
mode, the status LED glows by red color and in ready mode, it glows by green color. The other four LEDs
indicate the toner status. If the black toner needs to change, the toner-low (black) LED glows and if the
color (yellow, magenta, cyan) toners need to change, the toner-low (yellow, magenta, cyan) LED glows.
Functions
LED function is made up of
- Ready/Printing status display
- Error status display
- Toner low status display
Detail Description
LED control order
1) Control LED according to current printer state
: After the panel task is received each event, the LED operation is controlled by current printer status.
2) Write LED value to GOP (General Output Port)
Service Manual
LED behavior
Status LED
(Green/Red)
Black-only
LED
Toner-low
(CMYK)LEDs
Status
Green LED ON
N/A
N/A
Ready to receive the data.
Green LEDS
LOWLY BLINK
N/A
N/A
Receiving the data from the host.
Green LED
FAST BLINK
N/A
N/A
Printing the page.
Red LED BLINK
N/A
N/A
Paper source is set to MANUAL .

Need to push the button to start the
printing
Red LED ON
N/A
N/A
Out of paper
Red LED ON
N/A
N/A
Cover open
Red LED ON
N/A
N/A
Paper jam
Green/Red
N/A
CM
Service error ( LSU or Fuser error)
N/A
N/A
Toner-low(black) ON
Black toner needs to change
N/A
N/A
Toner-low(cyan) ON
Cyan toner needs to change
N/A
N/A
Toner-low(magenta) ON
Magenta toner needs to change
N/A
N/A
Toner-low(yellow) ON
Yellow toner needs to change
N/A
ON
N/A
Black only key is pressed
Service Error LED Operation

All LEDs blink the each time interval.
Service Error
Fuser Error
Scanner Error
(=LSU Error)
Service Manual
LED operation
Open Fuser Error
All LEDs (Toner low LEDs, Status (Red) LED) blink

a time interval of 1 second.
No Heat Error

a time interval of 4 seconds.
Over Heat Error
All LEDs (Toner low LEDs, Status (Green/Red) LED)

blink a time interval of 1 second.
P Motor Error
All LEDs (Toner low LEDs, Status (Green) LED)

H Sync Error
All LEDs (Toner low LEDs, Status(Green) LED)

blink a time interval of 4 seconds.
Assert Error LED Operation

The panel LED operation display the line number of assert error occurrence.
Line number
LED operation
start & end
All LEDs(Toner low LEDs, Status(Red) LED, turn ON for approximately 2 seconds and then All LEDs turn OFF for approximately 3 seconds.
After Status (Red) LED blinks one time, Toner low LEDs blink one time.
After Status (Red) LED blinks two times, Toner low LEDs blink one time.
After Status (Red) LED blinks three times, Toner low LEDs blink one time.
After Status (Red) LED blinks four times, Toner low LEDs blink one time.
After Status (Red) LED blinks five times, Toner low LEDs blink one time.
After Status (Red) LED blinks six times, Toner low LEDs blink one time.
After Status (Red) LED blinks seven times, Toner low LEDs blink one time.
After Status (Red) LED blinks eight times, Toner low LEDs blink one time.
After Status (Red) LED blinks nine times, Toner low LEDs blink one time.
Service Manual
Section 4 Repairs and Adjustments
Precautions
Precautions
In order to prevent accidents and to prevent damage to the equipment please read the precautions listed
below carefully before servicing the printer and follow them closely.
Safety Warning
(1) Only to be serviced by appropriately qualified service engineers.
High voltages and lasers inside this product are dangerous. This printer should only be serviced by a suitably
trained and qualified service engineer.
(2) Use only approved replacement parts
There are no user serviceable parts inside the printer. Do not make any unauthorized changes or
additions to the printer, these could cause the printer to malfunction and create electric shock or fire hazards.
(3) Laser Safety Statement
The Printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J for
Class 1(1) laser products, and elsewhere, it is certified as a Class I laser product
conforming to the requirements of IEC 825. Class I laser products are not considered to be hazardous. The
laser system and printer are designed so there is never any human access to laser radiation above a Class I
level during normal operation, user maintenance, or prescribed service condition.
Warning >> Never operate or service the printer with the protective cover removed from Laser/Scanner assembly. The
reflected beam, although invisible, can damage your eyes. When using this product, these basic safety
pre-cautions should always be followed to reduce risk of fire, electric shock, and injury to persons.
CAUTION - INVISIBLE LASER RADIATION

WHEN THIS COVER OPEN.
DO NOT OPEN THIS COVER.
VORSICHT - UNSICHTBARE LASERSTRAHLUNG,
WENN ABDECKUNG GE FFNET.
NICHT DEM STRAHL AUSSETZEN.
ATTENTION - RAYONNEMENT LASER INVISIBLE EN CAS
D OUVERTURE. EXPOSITION DANGEREUSE
AU FAISCEAU.
ATTENZIONE - RADIAZIONE LASER INVISIBILE IN CASO DI
APERTURA. EVITARE L ESPOSIZIONE AL
FASCIO.
PRECAUCION - RADIACION LASER IVISIBLE CUANDO SE ABRE.
EVITAR EXPONERSE AL RAYO.
ADVARSEL. - USYNLIG LASERSTR LNING VED BNING, N R
SIKKERHEDSBRYDERE ER UDE AF FUNKTION.
UNDG UDSAETTELSE FOR STR LNING.
ADVARSEL. - USYNLIG LASERSTR LNING N R DEKSEL
PNES. STIRR IKKE INN I STR LEN.
UNNG EKSPONERING FOR STR LEN.
VARNING - OSYNLIG LASERSTR LNING N R DENNA DEL
R PPNAD OCH SP RREN R URKOPPLAD.
BETRAKTA EJ STR LEN. STR LEN R FARLIG.
VARO! - AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTIINA N KYM TT M LLE LASERS TEILYLLE L KATSO S TEESEEN.
Service Manual
Precautions
Caution for safety

Toxic material
This product contains toxic materials that could cause illness if ingested.
(1) Please keep toner cartridges away from children. The toner powder contained in the toner cartridge may be harmful
and if swallowed you should contact a doctor.
Electric Shock and Fire Safety Precautions

Failure to follow the following instructions could cause electric shock or potentially cause a fire.
(1) Use only the correct voltage, failure to do so could damage the printer and potentially cause a fire or electric
shock.
(2) Use only the power cable supplied with the printer. Use of an incorrectly specified cable could cause the cable
to overheat and potentially cause a fire.
(3) Do not overload the power socket, this could lead to overheating of the cables inside the wall and could lead to
a fire.
(4) Do not allow water or other liquids to spill into the printer, this can cause electric shock. Do not allow paper
clips, pins or other foreign objects to fall into the printer these could cause a short circuit leading to an electric
shock or fire hazard..
(5) Never touch the plugs on either end of the power cable with wet hands, this can cause electric shock. When
servicing the printer remove the power plug from the wall socket.
(6) Use caution when inserting or removing the power connector. The power connector must be inserted completely otherwise a poor contact could cause overheating possibly leading to a fire. When removing the power
connector grip it firmly and pull.
(7) Take care of the power cable. Do not allow it to become twisted, bent sharply round corners or otherwise
damaged. Do not place objects on top of the power cable. If the power cable is damaged it could overheat and
cause a fire or exposed cables could cause an electric shock. Replace a damaged power cable immediately,
do not reuse or repair the damaged cable. Some chemicals can attack the coating on the power cable,
weakening the cover or exposing cables causing fire and shock risks.
(8) Ensure that the power sockets and plugs are not cracked or broken in any way. Any such defects should be
repaired immediately. Take care not to cut or damage the power cable or plugs when moving the machine.
(9) Use caution during thunder or lightening storms. Xerox recommend that this machine be disconnected from
the power source when such weather conditions are expected. Do not touch the machine or the power cord if it
is still connected to the wall socket in these weather conditions.
(10) Avoid damp or dusty areas, install the printer in a clean well ventilated location. Do not position the machine
near a humidifier. Damp and dust build up inside the machine can lead to overheating and cause a fire.
(11) Do not position the printer in direct sunlight. This will cause the temperature inside the printer to rise possibly
leading to the printer failing to work properly and in extreme conditions could lead to a fire.
(12) Do not insert any metal objects into the machine through the ventilator fan or other part of the casing, it could
make contact with a high voltage conductor inside the machine and cause an electric shock.
Service Manual
Precautions
Handling Precautions
The following instructions are for your own personal safety, to avoid injury and so as not to damage the printer
(1) Ensure the printer is installed on a level surface, capable of supporting its weight. Failure to do so could cause
the printer to tip or fall.
(2) The printer contains many rollers, gears and fans. Take great care to ensure that you do not catch your fingers,
hair or clothing in any of these rotating devices.
(3) Do not place any small metal objects, containers of water, chemicals or other liquids close to the printer which if
spilled could get into the machine and cause damage or a shock or fire hazard.
(4) Do not install the machine in areas with high dust or moisture levels, beside on open window or close to a
humidifier or heater. Damage could be caused to the printer in such areas.
(5) Do not place candles, burning cigarettes, etc. on the printer, these could cause a fire.
Assembly / Disassembly Precautions

Replace parts carefully, always use approved parts. Take care to note the exact location of parts and also
cable routing before dismantling any part of the machine. Ensure all parts and cables are replaced correctly.
Please carry out the following procedures before dismantling the printer or replacing any parts.
(1) Check the contents of the machine memory and make a note of any user settings. These will be erased if the
mainboard is replaced.
(2) Ensure that power is disconnected before servicing or replacing any electrical parts.
(3) Disconnect printer interface cables and power cables.
(4) Only use approved spare parts. Ensure that part number, product name, any voltage, current or temperature
rating are correct.
(5) When removing or re-fitting any parts do not use excessive force, especially when fitting screws into plastic.
(6) Take care not to drop any small parts into the machine.
(7) Handling of the OPC Drum
- The OPC Drum can be irreparably damaged if it exposed to light.
Take care not to expose the OPC Drum either to direct sunlight or to fluorescent or incandescent room
lighting. Exposure for as little as 5 mins can damage the surfaces photoconductive properties and will result
in print quality degradation. Take extra care when servicing the printer. Remove the OPC Drum and store it in
a black bag or other lightproof container. Take care when working with the covers(especially the top cover)
open as light is admitted to the OPC area and can damage the OPC Drum.
- Take care not to scratch the green surface of OPC Drum Unit.
If the green surface of the Drum Cartridge is scratched or touched the print quality will be compromised.
Service Manual
Precautions
Disregarding this warning may cause bodily injury

(1) Be careful with the high temperature part.
The fuser unit works at a high temperature. Use caution when working on the printer. Wait for the fuser to cool
down before disassembly.
(2) Do not put finger or hair into the rotating parts.
When operating a printer, do not put hand or hair into the rotating parts (Paper feeding entrance, motor, fan,
etc.). If do, you can get harm.
(3) When you move the printer.
This printer weighs 13.6kg including Consumables. Use safe lifting and handling techniques. Back injury could
be caused if you do not lift carefully.
(4) Ensure the printer is installed safely.
The printer weighs 13.6Kg, ensure the printer is installed on a level surface, capable of supporting its weight.
Failure to do so could cause the printer to tip or fall possibly causing personal injury or damaging the printer.
(5) Do not install the printer on a sloping or unstable surface. After installation, double check that the printer is stable.
Service Manual
Precautions when replacing parts

Precautions when assembling and disassembling
* Use only approved apporved spare parts. Ensure that part number, product name, any voltage, current or
temperature rating are correct. Failure to do so could result in damage to the machine, circuit overload,
fire or electric shock.
* Do not make any unauthorized changes or additions to the printer, these could cause the printer to malfunction and create electric shock or fire hazards.
* Take care when dismantling the unit to note where each screw goes. There are 19 different screws. Use of
the wrong screw could lead to system failure, short circuit or electric shock.
* Do not disassemble the LSU unit. Once it is disassembled dust is admitted to the mirror chamber and will
seriously degrade print quality. There are no serviceable parts inside.
* Regularly check the condition of the power cord, plug and socket. Bad contacts could lead to overheating
and fire. Damaged cables could lead to electric shock or unit malfunction.
Preautions when handling PBA

Static electricity can damage a PBA, always used approved anti-static precautions when
handling or storing a PBA.
>> Precautions when moving and storing PBA
1. Please keep PBA in a conductive case, anti-static bag.
2. Do not store a PBA where it is exposed to direct sunlight.
>> Precautions when replacing PBA

1. Disconnect power connectors first, before disconnecting other cables
2. Do not touch any soldered connections, connector terminals or other electronic parts when handling
insulated parts.
>> Precautions when checking PBA

1. Before touching a PBA, please touch other grounded areas of the chassis to discharge any static electrical charge on the body.
2. Take care not to touch the PBA with your bare hands or metal objects as you could create a short circuit or get an electric shock. Take extra care when handling PBAs with moving parts fitted such as sensors, motors or lamps as they may get hot.
3. Take care when fitting, or removing, screws. Look out for hidden screws. Always ensure that the correct
screw is used and always ensure that when toothed washers are removed they are refitted in their original positions.
Releasing Plastic Latches

Many of the parts are held in place with plastic latches. The latches break easily; release them carefully.
To remove such parts, press the hook end of the latch away from the part to
which it is latched.
Service Manual
Parts for Maintenance and Repair

Replacement interval for parts with a limited life
Some of the parts in this printer have a limited life, shorter than that of the whole machine. These parts
must be replaced periodically.
The table below shows the interval at which these parts should be replaced.
The table shows the life of each part, and is measured when using A4 paper. When servicing a machine
always check the status of these parts using the control panel and ensure that parts are replaced at the
appropriate times otherwise a general degradation in print quality will occur.
COMPONENT
REPLACEMENT CYCLE
REMARK
Toner Cartridge (Black)
intial (1,500 pages@5% coverage)

User replace
Toner Cartridge (Color: C/M/Y)
intial (700 pages@5% coverage)

Waste toner container
5K image or 1.25K pages

(Full color 5% image)
T2 Roller
100K pages
Imaging Unit
20K pages (Black)

12.5K pages (Color)
ITB Unit(Image Transfer Unit)
Black : (60K pages@5% coverage)

Color : (15K pages@5% coverage)
Pick-Up Roller
100,000 pages
- MP Pick-Up Roller,
- Cassette Tray1 Pick-Up Roller
Engineer
Fuser Unit
100,000 pages (B/W) Color(50,000 pages)
User replace
User replace
User replace
User replace
The life span of each of these parts is stored in memory. The amount of each 'life' used can be checked at
any time using the control panel.
When a part is replaced it is necessary to reset the 'life used' that is stored in memory.
* How to initialize a the value of part's life span:
From the control panel, select the following items in order:
Menu-Setup - Maintenance - Check other - (Select a desired part) - Reset
Service Manual
Critical Service Information

Warnings, Cautions, and Notes
Warnings
Personal injury or death may occur if
service personnel come into contact with
AC operating voltages.
Disconnect the power cord when removing
or replacing parts.
When diagnosing electrical problems
use care to avoid contact with AC voltages.
Cautions
Damage to the printer can occur if service
procedures aren't followed or careless service
methods are practiced. To avoid damage to the
printer review the intended action or procedure
before actually woorking on the printer.
Notes
Notes are used to communicate helpful tips
or relate conditions that may affect the
service action.
Service Manual
Information Related to Disassembly and Assembly

Special service parts
Never disassemble or adjust the items listed on this page except the Fuser.
1) Disassembly of the Laser Scan Unit

There are no serviceable parts inside the
LSU. Alignment of the mirrors is critical.
Opening the LSU will allow dust into the
laser and significantly reduce print quality.
It is very dangerous to operate or service
a machine with the LSU open or system
interlocks disabled. Exposure to laser
radiation can cause blindness.
2) Disassembly of the ITB unit

Do not disassemble the ITB. The alignment of the home sensor is critical and is
set up in the factory on a special jig.
Incorrect re-assembly will cause print
quality degradation.
3) Care of the Toner cartridge

Toner cartridges contain an extremely fine
powder. Please keep toner cartridges
away from children. The toner powder
contained in the toner cartridge may be
harmful and if swallowed you should contact a doctor. Take care not to spill toner spillages should be cleaned with a toner
vacuum cleaner and washed in cold
water (hot water sets the toner). Do not
touch the developer roller surface as contamination will reduce print quality. Take
care not to damage the roller's surface
when installing or removing a toner cartridge.
4) Disassembly of DEVE drive ass'y

and the main drive ass'y
The alignment of the drive mechanism is
critical and it has been set up in factory
using a jig and a driving gear. It is adjusted for the best gearing alignment. If the
motor is disassembled alignment would
not be maintained and this could cause
operational noise and image problems:
image alignment and toner distribution
may be affected.
5) Disassembly of terminal parts

Do not adjust the variable resistors on the
PBA. They have been already adjusted in
the factory.
6) Disassembly of the fuser unit

- The fuser melts toner onto the paper at
a high temperature: therefore, you need
to take special care not to get burned by
a hot fuser. When removing the fuser
from a set that has recently been operating you need to take extra care.
- Do not touch an AC line (Copper contact) on a main frame even after removing the fuser.
Service Manual
Precautions
ESD Precautions
Certain semiconductor devices can be easily damaged by static electricity. Such components are commonly called
Electrostatically Sensitive (ES) Devices, or ESDs. Examples of typical ESDs are: integrated circuits, some field
effect transistors, and semiconductor chip components.
The techniques outlined below should be followed to help reduce the incidence of component damage caused by
static electricity.
Caution >>Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
1. Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain off any
electrostatic charge on your body by touching a known earth ground. Alternatively, employ a commercially available wrist strap device, which should be removed for your personal safety reasons prior to applying power to the
unit under test.
2. After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface, such as
aluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity of the assembly.
3. Use only a grounded tip soldering iron to solder or desolder ESDs.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can
generate electrical charges sufficient to damage ESDs.
5. Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges sufficient to damage ESDs.
6. Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most
replacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a comparable conductive material.
7. Immediately before removing the protective shorting material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.
8. Maintain continuous electrical contact between the ESD and the assembly into which it will be installed, until completely plugged or soldered into the circuit.
9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushing
together of clothing fabric and lifting ones foot from a carpeted floor, can generate static electricity sufficient to
damage an ESD.
Super Capacitor or Lithium Battery Precautions

1. Exercise caution when replacing a super capacitor or Lithium battery. There could be a danger of explosion and
subsequent operator injury and/or equipment damage if incorrectly installed.
2. Be sure to replace the battery with the same or equivalent type recommended by the manufacturer.
3. Super capacitor or Lithium batteries contain toxic substances and should not be opened, crushed, or burned for
disposal.
4. Dispose of used batteries according to the manufactures instructions.
Service Manual
4 Disassembly Procedure
4.1 Covers
Top Cover
1. Open Front Cover and remove the
Imager Unit). CAUTION Protect the
Imager Unit from light.
2. Remove InterTransfer Belt Unit by

grasping bottom of ITB and pulling out
slightly until it releases, lower it slightly,
and continue pulling out to remove ITB.
NOTE: Observe removal path for,
especially rear of ITB for reinstallation.
CAUTION: Do not touch the ITB Belt.
Protect it from light.
3. Remove Screws (2) and remove Top

Cover by lifting the front of the cover
slightly and pulling forward to release
hidden clips at under rear of cover.
Right Cover
1. Perform steps for Top Cover.
2. Remove Screw (1), open Rear Cover
and Front Cover, use screwdriver to
disengage top cover locks, and
disengage bottom cover locks after
pulling cover away from printer.
4.1 Covers
Left Cover
1. Perform steps for Top Cover.
2. Open Rear Cover and Front Cover, use
screwdriver to disengage top cover
locks, and disengage bottom cover
locks after pulling cover away from
printer.
4.2 Fuser
WARNING: Observe safe working
practices. Click Warnings/Cautions for
Safety button on Repairs and Adjustments
menu if unsure about procedures. Fuser
may be hot.
1. Open Rear Cover.
2. Remove Fuser by removing Screws (4)
sliding the drive coupling as shown
(yellow arrow), and pull out to remove
Fuser.
CAUTION
While replacing the Fuser ensure the electrical connectors engage correctly.
4.3 LSU
menu if unsure about procedures.
1. Remove Top Cover (including Imager
Unit and ITB, 4.1). CAUTION: Protect
Imager Unit and ITB from light.
2. Remove LSU Cover by grasping sides
of cover and lifting. CAUTION: Use
care when moving cover past
connector (red arrow).
3. Disconnect left electrical plug, remove

Screws (3) and lift LSU enough to
access and disconnect right side
electrical plug and remove LSU.
Replacement
CAUTION: Ensure ground wires (red
arrows) are secured.
4.4 HVPS
1. Remove Top Cover and Left Cover
(including Imager Unit and ITB, 4.1).
CAUTION: Protect Imager Unit and ITB
from light.
2. Disconnect electrical plugs (2) from top
of HVPS. Remove Screws (6), remove
HVPS (CAUTION: red arrows show
spring contact locations behind PS) and
then disconnect bottom electrical plug
from rear. CAUTION Observe ESD
practices.
Replacement
Note: the screws are numbered on HVPS
for sequential installation. Ensure ground
wire is secured (lower right corner).
4.5 Main PWB
menu if unsure about safe working
practices.
1. Remove Right Cover, 4.1.
2. Disconnect electrical plugs from Main
PWB. Remove Screws (5) and remove
PWB. CAUTION: Observe ESD
practices.
Disassembly Procedure
4.6 SMPS
1. Remove Top Cover and Right Cover
2. Disconnect electrical plugs from SMPS.
Remove Screws (4) and remove
SMPS. CAUTION Observe ESD
practices.
4.5 Drive Unit
1. Remove Top Cover and Right Cover
2. Remove Main PWB (5.4.5).
3. Disconnect electrical plugs from Drive
Unit. Remove Screws (8) and screw
from ground wire and remove Drive
Unit. CAUTION Observe ESD
practices.
Replacement
Note: the screws are numbered for
sequential installation. Ensure ground
wires and ground resistor are secured
(arrows).
4.8 Transfer Roll
1. Open Rear Cover.
2. Remove Transfer Roll by removing
Screws (2) and guide. Then rotate
green lock up to release Transfer Roll
and remove it.
Replacement
CAUTION: Ensure ground wire is secure
(red arrow).
4.9 Imager
1. Open Front Cover and remove Imager
Unit. CAUTION: Protect the Imager
from light.
4.10 ITB
1. Open Front Cover and remove Imager.
CAUTION: Protect the Imager from
light.
2. Remove InterTransfer Belt Unit by

grasping bottom of ITB and pulling out
slightly until it releases, lower it slightly,
and continue pulling out to remove ITB.
NOTE: Carefully observe removal path,
especially at rear of ITB, for
reinstallation. CAUTION: Do not touch
the ITB Belt. Protect it from light.
4.11 Printer Cleaning

A printer should be regularly cleaned, especially if it is used in a dusty environment. This will ensure that
print quality remains high and failure due to contamination of printing services is less likely to occur.
* Clean the printer with a soft, lint free, cloth dipped in water.
* Do not touch the transfer roller when cleaning the inside of the printer. Grease and oils from the
skin will contaminate the surface and reduce print quality.
Cleaning the Printer

During the printing process, particles of paper, toner, and dust
can accumulate inside the printer. Over time, this build-up can
cause print quality problems such as toner specks or smearing.
Your printer has a cleaning mode that can correct and prevent
these types of problems.
Cleaning the Outside of the Printer

Clean the printer cabinet with a soft lint-free cloth. You can
dampen the cloth slightly with water, but be careful not to let
any water drip onto the printer or inside of it.
CAUTION: Cleaning the printer cabinet with cleaners

containing large amounts of alcohol, solvents, or other strong
substances can discolour or crack the cabinet.
Cleaning the Inside of the Printer

1
Turn the printer off and unplug the power cord, then wait a
few minutes for the printer to cool.
Open the front cover.
5.5
Pull the imaging unit out of the printer using the handle on
its bottom.
Look inside the printer. Remove any dust, paper particles,

and spilled toner with a damp, soft lint-free cloth.
NOTE: After cleaning, let the printer to dry completely.
Extend the top handle on the imaging unit and then use it
to pull the imaging unit out of the printer completely.
Holding the handle on the imaging unit, push the unit in to

the printer.
Close the front cover firmly.
CAUTION:
Do not touch the green surface on the imaging unit with
your hands or any other material. Use the handle on it in
order to avoid touching this area.
Be careful not to scratch the surface of the imaging unit.
To prevent damage, do not expose the imaging unit to light
for more than a few minutes. Cover it with a piece of paper
to protect it if necessary.
CAUTION: If the front cover is not completely closed, the

printer will not operate.
5.6
Plug the power cord in and turn the printer on.
4.12 Feed Roll-Rubber Pick Up
4. Remove Feed Roll by rotating roll

opposite normal feed direction so
release tabs are accessible, pushing in
both release tabs, pulling top of roll
away form shaft, rotating it down and
disengaging lower mounting tabs.
5. Remove Rubber Pick Up from support.
3. Remove LSU by disconnecting left

electrical plug, removing Screws (3)
and lifting LSU enough to access and
disconnect right side electrical plug
(CAUTION: Hold small PWB while
disconnecting plug, red arrow).
Replacement
NOTE: After replacing rubber pick up
rotate feed roll opposite normal feed
direction so the opening in feed roll
faces down.
CAUTION: When replacing LSU ensure
ground wires (red arrows) are secured.
4.13 Tray Empty Actuator
4. Remove Tray Empty Actuator by

removing Screw and pulling Actuator
housing up. NOTE: a small locating tab
on the bottom, under arrow, will resist
upward movement while disengaging.
Replacement
CAUTION: When replacing LSU ensure
ground wires (red arrows) are secured.
3. Remove LSU by disconnecting left
electrical plug, removing Screws (3)
and lifting LSU enough to access and
disconnect right side electrical plug
(CAUTION: Hold small PWB while
disconnecting plug, red arrow).
Adjustments
There are no adjustments in the Phaser
6110.
Section 5 Parts Lists
Item
1
2
3
4
5
5
6
7
8
9
10
11
12
13
14
15
16
17
18
18
19
19
20
21
22
23
23
29
30
30
31
32
33
Printer Exploded View Parts List

Description
Electrical Assembly Frame
110v/220v
Left Cover
Cassette Surround Panel
Control Panel Label
Printer USB PWB
Printer Network PWB
Main Drive
Toner Dispenser/Photoreceptor
Unit
InterTransfer Belt Module (ITB)
Yellow Toner Cartridge
Magenta Toner Cartridge
Cyan Toner Cartridge
Black Toner Cartridge
Paper Cassette
Top Cover
Rear Cover
Front Cover
Right Cover
Main PWB Mounting Frame (USB)
Main PWB Mounting Frame
(Network)
Switching Mode Power Supply
(SMPS) 110v
(SMPS) 220v
High Voltage Power Supply
(HVPS)
Laser Scanning Unit (LSU)
Laser Scanning Unit Cover
Fuser 110v
Fuser 220v
HVPS Contacts
Power Cord 110v
Power Cord 220v
Guide Stacker
Part Number
001N00489
002N02631
002N02635
N/A
140N63219
140N63220
007N01563
064N00058
023N01169
NA
NA
NA
NA
050N00506
002N02629
002N02630
002N02633
002N02632
095N00277
096N00278
105N02119
105N02118
105N02136
122N00263
002N02634
126N00279
126N00269
116N00251
N/A
N/A
038N00503
Tray Empty Actuator

120N00503
Feed Roll-Rubber Pick Up
130N01409
N/A Not available at time of publication
InterTransfer Belt Parts List
Item
Description
2
All
except
Item 2
Transfer Roller
InterTransfer Belt
Module (ITB)
Part
Number
022N02299
023N01169
Fuser Parts List
1
2
3
3
4
5
Description
Heat Roller
Pressure
Roller
Heat Lamp
220v
Heat Lamp
110v
Thermostat
Thermistor
Part Number
022N02300
022N02301
122N00264
122N00271
130N01491
130N01492
Hardware (Screws)
Type/Style
Size/
Length (mm)
M3 x 10
Type/Style
M3 x 6
Size/
Length (mm)
M4 x 10
M4 x 6
M3 x 10
M2 x 6
M3 x 12
M3 x 10
M3 x 6
M3 x 6
M3 x 8
Section 6 General Procedures and Information
Diagnostics are executed in the individual troubleshooting procedures at point of need in

Sections 2 or 3, when applicable.
The diagnostics method for this printer is operational diagnostics. That is, during normal
operation, electrical measurements can be made on electrical components to check
operating signals, or mechanical operations can be observed to discover mechanical
operational capability.
Below is a table of conditions indicated by the LEDs.
Error Message
LED status legend
LED pattern



representative.
Service Manual
Sample Pattern
This product provides several printable test patterns for maintenance purposes. These patterns can be used to aid the
diagnosis of print quality problems.
Printing a Configuration Page

You can print a configuration page from the printers control panel. Use the configuration page to view the current
settings, to help troubleshoot problems.
To print a configuration page: In ready mode, press and hold the Stop button on the control panel for 5 seconds.
A configuration page prints out.
Service Manual
Sample Pattern
This product provides several printable test patterns for maintenance purposes. These patterns can be used to aid the
diagnosis of print quality problems.
Printing a Demo Page

Print a demo page to make sure that the printer is operating correctly.
To print a demo page: In ready mode, press and hold the Stop button for 2 seconds.
A demo page showing the printers features and capabilities is printed.
Service Manual
Firmware Upgrade
This procedure is used to upgrade Firnware. It requires a Firmware File and an Upgrade Tool in a folder on a PWS.
A USB cable is required to connect the machine to the PWS.
PROCEDURE
Upgrade Firmware
1. Connect PC and Printer with USB Cable.
2. Switch on the machine.
3. Navigate to the folder on PWS that contains the Firmware File and the dosusb.EXE Firmware Upgrade Tool.
4. Drag and drop the Firmware File over the dosusb.EXE file and the upgrade will execute.
5. Check the DOS command window activity on the PWS. When the DOS command window activity stops and
when the LEDs indicates Ready switch off the Phaser 6110.
6. Disconnect the USB cable and switch on the Phaser 6110 to complete the procedure.
Jam Removal
When a jam occurs while printing a jam message is displayed on the control panel.
* Jam0 In Tray 1:
Paper jam in the main cassette.
* Jam0 In MP Tray:
Paper jam in the MP tray
* Jam Inside Printer:
Jam 1, Paper is jammed inside the printer.
* Jam In Exit Area:
Jam2, Paper is jammed in the exit area when ejecting paper.
CAUTION: When removing jammed paper, always pull it firmly and evenly without any sudden jerks. If
at all possible, remove the paper as a single sheet. If the paper tears ensures ALL paper
fragments are removed. Any fragments left inside the machine will cause it to jam again.
Clearing Paper Jams

NOTE: When removing paper that is jammed in the printer, if possible always pull the paper in the direction
that it normally moves so as not to damage internal components. Always pull firmly and evenly; do
not jerk the paper. If the paper tears, ensure that all fragments of paper are removed; otherwise a
jam will occur again.
If a paper jam occurs, the Status LED on the control panel lights red. Find and remove the jammed paper.
To resume printing after clearing paper jams, you must open and close the front cover or rear cover.
1. To remove the jammed paper, open the rear
cover.
2. Carefully remove the paper by pulling in the

direction as shown below. Most of the jammed
paper can be removed in this step.
If you cannot find the jammed paper, or if there

is any resistance removing the paper, stop
pulling and go to the next step.
Service Manual
3. Close the rear cover and then open the top

cover.
4. Holding the inner cover open, carefully take the

jammed paper out of the printer. The inner
cover will then close automatically.
5. Close the top cover. Make sure that it is

securely latched.
6. Open and then close the rear cover or front

cover to resume printing.
Service Manual
Tips for Avoiding Paper Jams

By selecting the correct paper types, most paper jams can be avoided.
Follow the procedures Jam remove. Ensure that the adjustable guides are positioned correctly.
Do not overload the paper tray.
Do not remove the paper from the tray while printing.
Flex, fan, and straighten the paper before loading.
Do not use creased, damp, or highly curled paper.
Do not mix paper types in a tray.
Use only recommended print materials.
Ensure that the recommended print side of print materials is facing up in the paper tray.
Service Manual
Product Specifications
Product Overview
Service Manual
2-1
Specifications
Specifications are correct at the time of printing. Product specifications are subject to change without notice.
See below for product specifications.
General Specifications
2-2
Service Manual
Controller & S/W
Service Manual
2-3
Paper Handling
2-4
Service Manual
Consumables
Service Manual
2-5
Environment
Options
2-6
Service Manual
Reference Information
Select a location for the printer

Leave enough room to open the printer trays, covers, and allow for proper ventilation. (see diagram
below)
Provide the proper environment :
- A firm, level surface
- Away from the direct airflow of air conditioners, heaters, or ventilators
- Free of extreme fluctuations of temperature, sunlight, or humidity
- Clean, dry, and free of dust
Service Manual
Consumables
Service Manual
Hardware (Screws)
Type/Style
Size/
Length (mm)
M3 x 10
Type/Style
M3 x 6
Size/
Length (mm)
M4 x 10
M4 x 6
M3 x 10
M2 x 6
M3 x 12
M3 x 10
M3 x 6
M3 x 6
M3 x 8
This chapter contains the tools list, list of abbreviations used in this manual, and a guide to the
location space required when installing the printer. A definition of tests pages and Wireless
Network information definition is also included.
Tools for Troubleshooting

The following tools are recommended safe and easy troubleshooting as described in this service manual.
DVM(Digital Volt Meter)
Standard : Indicates more than 3 digits.
Driver
Standard : "-" type, "+" type (M3 long, M3 short, M2
long, M2 short).
Cleaning Equipments
Standard : An IPA(Isopropyl Alcohol)dry wipe tissue or a
gentle neutral detergent and lint-free cloth.
Vacuum Cleaner
Brush
Tweezers
Standard : For general home use, small type.
Cotton Swab
Standard : For general home use, for medical service.
Software (Driver) installation CD ROM

Install Driver CD
Network S/W CD
Service Manual
Acronyms and Abbreviations

The table below explains the abbreviations and acronyms used in this service manual. Where abbreviations
or acronyms are used in the text please refer to this table.
ADC
Analog-to-Digital-Conversion
EPP
Enhanced Parallel Port
AP
Access Point
F/W
Firmware
AC
Alternating Current
FCF/FCT
ASIC
Circuit
Application Specific Integrated
First Cassette Feeder/First

Cassette Tray
FISO
Front-In, Side-Out
ASSY
Assembly
FPOT
First Print out Time
BIOS
Basic Input Output System
GDI
Windows Graphic Device Interface
BLDC Motor
Brushless DC Motor
GIF
Graphic Interchange Format
CLBP
Color Laser Beam Printer
GND
Ground
CMOS
Complementary Metal Oxide

Semiconductor
HBP
Host Based Printing
CMYK
Cyan, Magenta, Yellow, Black
HDD
Hard Disk Drive
CN
Connector
HTML
Hyper Text Transfer Protocol
CON
Connector
HV
High Voltage
CPU
Central Processing Unit
HVPS
High Voltage Power Supply
CTD Sensor
Color Toner Density Sensor
I/F
Interface
dB
Decibel
I/O
Input and Output
dBA
A-Weighted decibel
lb
Pound(s)
dBm
Decibel milliwatt
IC
Integrated Circuit
DC
Direct Current
ICC
International Color Consortium
DCU
Diagnostic Control Unit
IDE
Intelligent Drive Electronics or

Integrated Drive Electronics
DIMM
Dual In-line Memory Module
IEEE
DPI
Dot Per Inch
Institute of Electrical and

Electronics Engineers. Inc
DRAM
Dynamic Random Access Memory
IOT
Image Output Terminal (Color printer, Copier)
DVM
Digital Voltmeter
IPA
Isopropy Alcohol
ECP
Enhanced Capability Port
IPC
ECU
Engine Control Unit
Inter Process CommunicationEPP

Enhanced parallel Port
EEPROM
Electronically Erasable
Programmable Read Only Memory
IPM
Images Per Minute
ITB
Image Transfer Belt
EMI
Electro Magnetic Interference
LAN
local area network
EP
Electro photographic
LBP
Laser Beam Printer
Service Manual
PTB
Paper-Transfer Belt
LED
Light Emitting Diode
PWM
Pulse Width Moduration
LSU
Laser Scanning Unit
Qty
Quantity
MB
Megabyte
RAM
Random Access Memory
MHz
Megahertz
RCP
Remote Control Panel
MPBF
Mean Prints Between Failure
ROM
Read Only Memory
MPF/MPT
Multi Purpose Feeder/Multi

Purpose Tray
SCF/SCT
Second Cassette Feeder/Second

Cassette Tray
NIC
Network Interface Card
SMPS
NPC
Network Printer Card
SPGP
NVRAM
Nonvolatile Random Access

Memory
Samsung Printer Graphic

Processor
SPL
Samsung Printer Language
OPC
Organic Photo Conductor
SPL-C
Samsung Printer Language-Color
PBA
Printed Board Assembly
Spool
PCL
Printer Command Language ,

Printer Control Language
Simultaneous Peripheral Operation

Online
SRS
Software Requirment Specification
PCI
Peripheral Component
Interconnect by Intel 1992/6/22, is
a local bus standard developed by
Intel and introduced in April, 1993 :
A60, B60 Pins
SURF
Surface Rapid Fusing
SW
Switch
sync
Synchronous or Synchronization
T1
ITB
T2
Transfer Roller
PCL5Ce
Printer Command Language 5CeColor
PCL6
Printer Command Language 6
TRC
Toner Reproduction Curve
PDF
Portable Document Format
PnP
Universal Plug and Play
PDL
Page Description Language
U.I.
User Interface
Ping
Packet internet or Inter-Network

Groper
URL
Uniform Resource Locator
PPD
Postscript Printer Discription
USB
Universal Serial Bus
PPM
Page Per Minute
VCCI
PS
Post Script
Voluntary Control Council for

Interference Information
Technology Equipment
PS3
Post Script Level3
WECA
Alliance
Wireless Ethernet Compatibility
PTL
Pre-Transfer Lamp
Wi-Fi
Wireless Fidelity
Service Manual
Section 7 Wiring Data
2M B
nRD,n WR,nCS
2P
DATA[31:16]
USB_D
Conn
USB2.0
System Clock
12MHz
ADDR[13:2]
Dev
3P
32.768KHz
nRD,nWR,nCS
12MHz
USB_H
Module
2P
DATA[31:16]
USB2.0
PLL
ADDR[9:2]
Host
RJ- 45
SD[31:0]
DATA[ 31:24]
Sm art
DAA
ADDR[8:2]
nRD,nWR, nCS
TX_CLK,RX_CLK,
MAC_TXD[3:0]
N/W
STE100P
SDRA M Cont rol ler
SA[12:0],BA0,1
Local Cont rol ler
nSCS0,1
nRAS,nCAS,
nWE,DQM,CKE,
SDCLK0,1
MAC
ADC 8ch
UART
PWM 8ch
I2C
LSU
Cont roller
SDRAM
SDRAM
32MB
3P
4P
5P
EEPROM
32K bit
SR A M
64K B
SCL
SDA
SRAM_D[15:0]
GPIO
SRAM_A[15:0]
OP E G D I 12 P
7k e y,2 L E D
3P
9600bps
HPVC
Image Proce ssor
16 *2 L C D
AFE
AFE,CCD
Control
HT82V 26
22 P
LV DS
FIN1047
2P
DEV E JOINT
DE
I
T
B
C
L
T
2P
P
I
C
K
U
P
C
L
T
3P
R
E
G
I
C
L
T
T
2
C
L
T
3P
D
E
V
S
O
L
3P
2P
C
O
V
E
R
S
/
W
14 P
L
S
U
10 P
B
L
D
C
PCB Cont act
EXIT SENSOR
REGI
SENSOR
P_EMPTY
SENSOR
7P
CRUM
Dev e CR
De
CRUM
CR
CRUM
CR
CRUM
CR
CRUM
CR
MC34 C02
MP_EMPTY
CTD
2P
PICKUP
HOME
Charger 1ea
T1 1ea
T2 1ea
Bi as AC 1ea
DC 1ea
TEMP2
SE NSOR
Light - Receiver
WASTE
SENSOR
Light - Emit
WASTE
SENSOR
2P
RELAY
Dev Bi as Y
De
RELAY
Dev Bi as M
De
RELAY
Dev Bi as C
De
RELAY
Dev Bi as K
De
Zener
Di ode
SUPPLY Y,M,C,K
FUSER
SMPS
SM
2P
E- Coil
1P
Thermo stat
Standa
dard Type
pe 3
[ Not e]
in Use
+24V 4.
4.5A
5A, +5V
5V 3A
2P
INLET&SWITCH
Res erved
Connection Diagram
S
C
F
2P
Service Manual
F
A
N
M
A
I
N
8P
A
D
F
2P
C
C
D
24 P
B
A
T
24 P
16P
PTL
THERMISTOR
HVPS
HV
PS
STEP
Mo tor
2P
ITB HOME
SENSOR
TEMP1
SENSOR
DEVE HOME
SENSOR
MAC_RXD[3:0]
25MHz
OP E M F P
3P
ARM9- 300MHz
6MHz
RJ- 11
3P
CH
CHORUS
m
nRD,nWR,nCS
RJ- 11
RTC
5P
Connection Diagram
DRA WER CON.
ADDR[22:2]
110
ITB JOINT
NT
MAIN
MA
DATA[31:0]
Flash
DRA WER CON.
ADDR[22:2]
2M B
nRD,n WR,nCS
USB_D
Conn
USB2.0
System Clock
12MHz
ADDR[13:2]
Dev
3P
32.768KHz
nRD,nWR,nCS
12MHz
USB_H
Module
2P
DATA[31:16]
USB2.0
PLL
ADDR[9:2]
Host
RJ- 45
SD[31:0]
DATA[ 31:24]
Sm art
DAA
ADDR[8:2]
nRD,nWR, nCS
TX_CLK,RX_CLK,
MAC_TXD[3:0]
N/W
STE100P
SDRA M Cont rol ler
SA[12:0],BA0,1
Local Cont rol ler
nSCS0,1
nRAS,nCAS,
nWE,DQM,CKE,
SDCLK0,1
MAC
ADC 8ch
UART
PWM 8ch
I2C
LSU
Cont roller
SDRAM
SDRAM
32MB
3P
4P
5P
EEPROM
32K bit
SR A M
64K B
SCL
SDA
SRAM_D[15:0]
GPIO
SRAM_A[15:0]
OP E G D I 12 P
3P
7k e y,2 L E D
9600bps
HPVC
AFE
AFE,CCD
Control
Image Proce ssor
16 *2 L C D
HT82V 26
22 P
LV DS
FIN1047
2P
24 P
DEV E JOINT
DE
I
T
B
C
L
T
2P
P
I
C
K
U
P
C
L
T
3P
R
E
G
I
C
L
T
2P
C
O
V
E
R
S
/
W
14 P
L
S
U
10 P
B
L
D
C
16P
PCB Cont act
EXIT SENSOR
REGI
SENSOR
P_EMPTY
SENSOR
7P
CRUM
Dev e CR
De
CRUM
CR
CRUM
CR
CRUM
CR
CRUM
CR
MC34 C02
MP_EMPTY
CTD
2P
PICKUP
HOME
Charger 1ea
T1 1ea
T2 1ea
Bi as AC 1ea
DC 1ea
TEMP2
SE NSOR
Light - Receiver
WASTE
SENSOR
Light - Emit
WASTE
SENSOR
2P
RELAY
Dev Bi as Y
De
RELAY
Dev Bi as M
De
RELAY
Dev Bi as C
De
RELAY
Dev Bi as K
De
Zener
Di ode
SUPPLY Y,M,C,K
FUSER
SMPS
SM
2P
E- Coil
1P
Thermo stat
Standa
dard Type
pe 3
[ Not e]
in Use
+24V 4.
4.5A
5A, +5V
5V 3A
2P
INLET&SWITCH
Res erved
Connection Diagram
T
2
C
L
T
3P
D
E
V
S
O
L
3P
S
C
F
2P
Service Manual
F
A
N
M
A
I
N
8P
A
D
F
2P
C
C
D
24 P
B
A
T
THERMISTOR
HVPS
HV
PS
STEP
Mo tor
PTL
TEMP1
SENSOR
DEVE HOME
SENSOR
MAC_RXD[3:0]
25MHz
OP E M F P
3P
ARM9- 300MHz
6MHz
RJ- 11
3P
CH
CHORUS
m
nRD,nWR,nCS
RJ- 11
RTC
2P
ITB HOME
SENSOR
. Connection Diagram
2P
DATA[31:16]
5P
10
Flash
ITB JOINT
NT
MAIN
MA
DATA[31:0]
SMPS-110V
Schematic Diagram
R04
1K_2012
C72
1KV103K
D103
F02
250V5A
R01
C02
AD102
TH01
10D9
R11
C01
224
LF002
CV930160
R02
C03
AD102
C04
104
BD01
600V6A
R03
C11
200V680uF
200K_3216X3
AR01
600V
R12
R13
C18
AD102
R14
39KX3_3216
CON1 TNR01
14D221
D01
1KV1A-CHIP
AR04
600V
L01
LF01
DV508080S
200KX3_3216
F01
250V8A
R010
1W22(mini)
Q01
600V12A
AR03
1KV
T1
C05
104K_2012
CON3-3,5,7,9
C12
630V333K
24V 4.4A
ZD71
20V-CHIP
R15
Q11
600V4A
R17
100_2012
R77
R75
200_2012 3W120
C71
C75
C77
35V470uF
R16
AR02
1KV
35V1000uFX2
D105
200V20AX2
Q71
2222A-CHIP
ZD12
20V-CHIP
C78
50V104(mono)
R76
470_2012
L51
CON2-2
R52
C51
630V333k
R51
1W50m
CON3-4,6,8,10
CON2-1
GND
R53
91JX2_2012
C73
1KV103K
Q51
600V16A
R91
220_2012
PC51
TLP3061F
0
R54
1W50m
CON3-11,13,15
5V 3A
U11
IC_1207A-CHIP
R18
10_2012
Q12
500V21A
D104
60V20A
OUT
VI
R19
100_2012
R20
10K_2012
D11
1KV1A-CHIP
7
NC
VCC
DEMAG
R23
47_3216
R21
100_2012
R24
100K_2012
FB
2
R56
1W1.5KJ(mini)
CS
GND
R55
1/2W180(MINI)
F71
250V5A
D12
MMSD4148
5
R59
C52
100_2012 104K_2012
L71
5uH
PC11-1
817B
CON3-1
C14
PC11-2
817B
C74
16V1000uF
R92
1K_2012
R93
1KF_2012
C91
225_2012
C76
16V1000uF
U91
431-CHIP
R94
1KF_2012
C15
24VS
C13
1n_2012
Fuser Count
R58
4.7K_2012
35V47uF
R22
5W0.13
CON3-2
100n_2012
Q52
2222A-CHIP
R57
1K_2012
C16
20p_2012
CON3-12,14,16
GND
ZD11
20V-CHIP
TNR11
7D221
C17
AD102
HEATSINK
Service Manual
SMPS-220V
Schematic Diagram
R04
1K_2012
C72
1KV103K
D103
F02
250V5A
R01
C02
AD102
TH01
10D9
R11
C01
224
LF002
CV930160P
R02
C03
AD102
C04
104
BD01
600V6A
R03
C11
450V220uF
200K_3216X3
AR01
600V
R12
R13
C18
AD102
R14
91KX3_3216
CON1 TNR01
10D561
D01
1KV1A-CHIP
AR04
600V
L01
LF01
CV505110B
200KX3_3216
F01
250V8A
R010
1W22(mini)
Q01
600V12A
AR03
1KV
T1
C05
104K_2012
CON3-3,5,7,9
C12
630V333K
24V 4.4A
ZD71
20V-CHIP
R15
Q11
600V4A
R17
100_2012
R77
R75
200_2012 3W120
C71
C75
C77
35V470uF
R16
AR02
1KV
35V1000uFX2
D105
200V20AX2
Q71
2222A-CHIP
ZD12
20V-CHIP
C78
50V104(mono)
R76
470_2012
L51
CON2-2
R52
C51
630V333k
R51
1W50m
CON3-4,6,8,10
CON2-1
GND
R53
91JX2_2012
C73
1KV103K
Q51
600V16A
R91
220_2012
PC51
TLP3061F
0
CON3-11,13,15
5V 3A
U11
IC_1207A-CHIP
R18
10_2012
Q12
600V11A
D104
60V20A
OUT
VI
R19
100_2012
R20
10K_2012
D11
1KV1A-CHIP
7
NC
VCC
DEMAG
R23
47_3216
R21
100_2012
R24
100K_2012
FB
2
R56
1W1.5KJ(mini)
CS
GND
R55
1/2W180(MINI)
F71
250V5A
D12
MMSD4148
5
C52
104K_2012
R59
22_2012
R54
1W50m
L71
5uH
PC11-1
817B
CON3-1
C14
PC11-2
817B
C74
16V1000uF
R92
1K_2012
R93
1KF_2012
C91
225_2012
C76
16V1000uF
U91
431-CHIP
R94
1KF_2012
C15
24VS
C13
1n_2012
Fuser Count
R58
4.7K_2012
35V47uF
R22
5W0.25
CON3-2
100n_2012
Q52
2222A-CHIP
R57
1K_2012
C16
20p_2012
ZD11
20V-CHIP
TNR11
7D221
HEATSINK
C17
AD102
CON3-12,14,16
GND
Panel
Schematic Diagram
MAIN PANEL
Service Manual
HVPS (1/5)
Schematic Diagram
Service Manual
HVPS (2/5)
Service Manual
Schematic Diagram
HVPS (3/5)
Schematic Diagram
Service Manual
11-23
HVPS (4/5)
Service Manual
Schematic Diagram
HVPS (5/5)
Schematic Diagram
Service Manual
DEVE INF
Schematic Diagram
FROM MAIN BOARD
WASTE LEVEL
R7
15K
CN3-1
35303-0350
1
2
3
DGN D
DGN D
DEVE CRUM
WASTE EMPTY
DGN D
A0
A1
A2
DGN D
DEVE
DGN D
TONER_CRUM_CONTACT_Y
DGN D
TONER_CRUM_CONTACT_M
DGN D
TONER_CRUM_CONTACT_C
DGN D
DGN D
DGN D
DGN D
TONER_CRUM_CONTACT_K
DGN D
DGN D
Service Manual
ITB INF
Schematic Diagram
PTL
FROM_DRAW_CON
Service Manual
ITB_HO ME
Section 8 Top Problems
Vapour may be seen emanating from the Fuser area. This may occur with
paper with a higher moisture content or in environments with higher
humidity. SURF, or Surface Rapid Fusing technology is used to optimize
image quality while reducing toner consumption. The rapid temperature
change during fusing may release moisture in the form of a visible vapour.
Section 9 Installation and Kits
Setting Up Your Printer
NOTES:
If any items are missing or damaged, notify your dealer

immediately.
Components may differ from one country to another.
The Printer Driver CD contains the printer driver, the SetIP,
the Users Guide, and the Adobe Acrobat Reader program.
The appearance of the power cord may differ depending on
your countrys specifications. The power cord must be
plugged into a grounded power socket.
This chapter gives you step-by-step instructions for setting up

your printer.
This chapter includes:
Unpacking
Installing the Toner Cartridges
Loading Paper
CAUTION: Because your printer weighs 13.6 kg including the
toner cartridges and the tray, it may move when you use it; for
example, when opening/closing the tray or installing/removing
the toner cartridge. Be careful not to move the printer.
Connecting a Printer Cable

Turning the Printer On
Installing the Printer Software
Pull the tray out of the printer and remove the packing
tape from the tray.
Select a location for the printer:
Unpacking
1
Remove the printer and all of the accessories from the

packing carton. Make sure that the printer has been
packed with the following items:
Toner Cartridges
Leave enough room to open the tray and covers, and to

allow for proper ventilation.
Power Cord
Provide the proper environment:

- A firm, level surface
- Away from the direct airflow of air conditioners,
heaters, or ventilators
Printer software CD
- Free of temperature, sunlight, and humidity extremes

or fluctuations
Quick Install Guide
2.1
- Clean, dry, and free of dust
Holding the toner cartridges, shake thoroughly them from

side to side to distribute the toner.
Remove the cartridges cap.
CAUTION: You must place your printer on a level surface. If

you do not, print quality problems can occur.
NOTE: If toner gets on your clothing, wipe it off with a dry

cloth and wash it in cold water. Hot water sets toner into
fabric.
Installing the Toner Cartridges

1
Open the front cover.
On the imaging unit of the printer, labels identify which

colour cartridge goes into each cartridge slot.
Magenta
Cyan
Yellow
Black
Remove the toner cartridges from their bags.
2.2
Grasp the toner cartridges and align them with the slots
inside the printer. Insert them into their corresponding
slots until they click into place.
Loading Paper
The tray can hold a maximum of 150 sheets of 20 lb (75 g/m2)
plain paper. You can use various paper including plain paper.
To load paper:
Pull the tray out of the printer.
Open the paper cover.
Unlatch the tray locks in the middle of the tray by pressing

them firmly and pull the tray out to extend it.
Close the front cover. Make sure that the cover is securely
closed.
CAUTION: If the front cover is not completely closed, the

printer will not operate.
NOTE: When printing text at 5% coverage, you can expect a

toner cartridge life of about 2,000 pages for black and white
printing and 1,000 pages for colour printing.
2.3
Flex the paper sheets back and forth to separate the pages
and then fan them while holding one edge. Tap the edges
of the stack on a flat surface to even it up.
Load paper with the print side up.
Squeeze the paper length guide and slide in it until it

lightly touches the end of the paper stack.
Close the paper cover.
Slide the tray back into the printer.
Make sure not to overfill the tray and that all four corners
are flat in the tray and under the brackets, as shown
below. Overfilling the tray may cause a paper jam.
NOTE: If you want to change the size of the paper in the tray,
refer to Changing the Size of the Paper in the Tray on
page 2.5.
NOTE: After you load paper, you need to set up your printer
for the paper type, size, and source you loaded. For details,
see the Software Section.
2.4
Changing the Size of the Paper in the

Tray
To change the tray size to other size, you must adjust the paper
length guide properly.
Slide the paper length guide until it lightly touches the end
of the paper stack. Squeeze the paper width guide and
slide it to the edge of the paper stack without causing it to
bend.
Pull the tray out of the printer. Open the paper cover and
remove paper from the tray if necessary.
For paper smaller than Letter-sized, return the paper

guides to their original positions and adjust the paper
length guide and paper width guide.
Pressing and unlatching the guide lock in the top of the

tray, pull the tray out manually.
NOTES:
Do not push the width guide far enough to cause the

material to warp.
If you do not correctly adjust the width guide, it may cause a
paper jam.
Load paper into the tray.
2.5
Close the paper cover.
Slide the tray back into the printer.
Connecting a Printer Cable
For Network Printing (Phaser 6110N

only)
For Local Printing
You can attach your printer to a network using an Ethernet

cable (UTP cable with RJ.45 connector). The Phaser 6110N has
a built-in network interface card.
To print from your computer in a local environment, you need

to connect your printer to the computer with a Universal Serial
Bus (USB) cable.
If you are a Macintosh user, you can use only a USB cable.
Make sure that both the printer and the computer are
turned off.
Plug one end of the Ethernet cable into the Ethernet

network port on the rear of the printer.
NOTE: Connecting the printer to the USB port of the computer

requires a certified USB cable. You will need to buy a USB 2.0
compliant cable that is not longer than 3 m.
Make sure that both the printer and the computer are
turned off.
Plug the USB cable into the connector on the rear of the
printer.
To the network LAN

connection
Plug the other end of the cable into a network LAN

connection.
NOTE: After connecting the printer, you need to configure the

network parameters using the software supplied with the
printer.
Connect the other end of the cable to the USB port on your
computer.
NOTE: To print using the USB interface, you must run Windows
98/Me/2000/2003/XP or Macintosh with OS 10.3 ~10.4.
2.6
Turning the Printer On
Installing the Printer Software
Plug the power cord into the power receptacle on the rear
of the printer.
Plug the other end into a properly grounded AC outlet and

turn on the power.
You must install software using the supplied

printer driver CD after you have set up your
printer and connected it to your computer. For
details, see the Software Section.
The printer driver CD provides you with the following software:
Programs for Windows

You can install the following printer software using the printer
driver CD.
Printer driver for Windows. Use this driver to take full
advantage of your printers features. See the Software
Section for details about installing the Xerox printer driver.
Status Monitor. Appears when printing errors occur. See
the Software Section for details about installing the Status
Monitor program.
Printer Settings Utility. you can configure print settings.
CAUTION:
Macintosh Printer Driver
Some parts inside the printer may be hot when power is on,
or after printing. Be careful not to burn yourself when
working inside the printer.
Do not disassemble the printer when it is turned on or
plugged in. Doing so may give you an electric shock.
You can print from a Macintosh with your printer. Go to the

Software Section for information about installing the print
software and printing from a Macintosh.
Linux Driver
You can print from a Linux-based computer with your printer.
Go to the Software Section for information about installing
the Linux driver and printing from a Linux environment.
NOTE: Each LED blinks red in a repeated order. Wait for about
three minutes for the printer to get ready.

Print a demo page to make sure that the printer is operating
correctly.
To print a demo page:
In Ready mode, press and hold the
button for 2 seconds.
A demo page showing the printers features and capabilities is

printed.
2.7
Section 10 Product Technical Overview
At this time there are no options or kits available.

The printer is purchased in a configuration that matches
customer requirements.
Repack Procedure
menu if unsure about safe working
practices.
CAUTION: The purpose of Repack is to
prevent toner from migrating throughout
the machine during the return shipment to
a service center.
3. Remove the toner cartridges and install

the clear plastic shipping cover
(shipping cover is installed on all new
cartridges). Secure the Cartridges into
the output tray or top of the machine for
shipping.
1. Remove the Waste Toner Cartridge.
2. Remove the Waste Toner Retainer Cap

from the storage position and install the
cap on the return port. Secure the
Waste Toner Cartridge into the top of
the machine for shipping.
4. Close the Toner Ports by installing the

Shipping Plugs into the Toner Ports. If
the plugs are not available close the
ports with tape, or wadded tissue or
wadded paper.
5. On the Phaser 6110MFP lock the

Scanner in the shipping position by
moving the lock tab to the rear (top of
output tray).
6. Remove the Paper Tray and secure it

on the top of the machine for shipping.
7. Remove the Power Cord and secure it
on the top of the machine for shipping.
NOTE: The machine is now ready for
shipping.
System Overview
System Overview
This chapter describes the functions and operating principles of the main components.
System Structure
Main Parts of System
Service Manual
System Overview
Cassette
Feeding Method : Cassette Type
Feeding Standard : Center Loading
Feeding Capacity : Cassette 150 Sheets(75g/ , 20lb Paper Standard)
No Manual Feeder
Paper Detecting Sensor : Photo Sensor (Empty, Registration, Exit)
Paper Size Sensor : None
LSU(Laser Scan Unit)
Consisted of LD(Laser Diode) and Polygon Motor Control.
Error
Phenomenon
Polygon Motor Error
The Rotation of Polygon Motor can not reach stable
Hsync Error
Though the rotation of Polygon Motor reach stable, the signal of Hsync is not occurred
2nd Transfer Ass y

The life span: Print over 100,000 sheets (in 15~30
Fuser Ass y
Heat Lamp : New Part - Knuckle Type
2 Pressure Roller : One is similar to HummingBird, the Other is a new added part comparing with
other Fuser
Thermistor - Temperature-Measuring Device
Thermostat - Critical Temperature-Detecting Device
&
ITB(Intermediate Transfer Belt) & 1st Transfer Roller

The life span: Print over 60K, Black; 15K Color
The ITB unit includes 1st Transfer Roller
&
OPC(Organic Photo-Conductor) & Developer

The life span: Print over 44,000 Images (Both)
Imagine Unit consists of 4 kinds of Developer , OPC, and Deve. Main Frame
Toner Kits
The life span: Color -> 1000 images (5% Coverage Print-Out)
Black -> 2000 images (5% Coverage Print-Out)
Driver Ass y
It is a power delivery unit by gearing
By driving the motor, it supplies the power to the feeding unit, the fusing unit, and the distributing unit.
Service Manual
System Overview
EP Process
- Structure of EP Process
P1: Image
on OPC
Blade
ITB Unit
P2: Image
on Media
Media Path
OPC
Blade
~
Developer
Laser Scanning Unit
Eraser
Charger
Service Manual
System Overview
- System Outline
Paper path
Exit
Fuser
Toner
Cartridge
Dev-Y
OPC
Dev-M
Dev-C
ITB
Dev-K
LSU
Cassette
Charging
Conductive Roller charging
Roller resistivity : ~ 10^5 ohm-cm
Applied voltage : -1.1kV
Charge acceptance : -520V
OPC coating thickness : 21um
OPC diameter : 60mm
Non eraser system
1. Organic Photoconductor is charged to uniform voltage by conductive roll charging method
2. No ozone is produced because corona is not used
3. Charger roll is cleaned with cleaning roll
4. Toner remained on OPC after T1 process is cleaned by cleaning blade and retrieved into waste toner
box by auger and belt driving mechanism
Service Manual
System Overview
Exposing
One polygon motor ( 6 facet )
Single beam LD (1ea)
LD wavelength : 785nm
Polygon motor rpm : 23747.5
LSU energy : 0.25uJ/cm^2
OPC exposed potential : -50V
1. Exposing is implemented by laser striking on to OPC with uniform potential
2. Laser beam is modulated according to image to be printed that is from PC
3. Latent Image is formed on OPC, which is developed with toner
Developing
Non-magnetic, mono component
Non-contact development
Developing bias : DC + AC
AC peak to peak : 1.5 ~ 2.0kV
Mass on developing roller : 550 ~ 600ug/cm^2
Toner coulomb : 15 ~ 20uC/g
Roller diameter : 10mm
Roller resistivity : 10^5 ~ 10^6 ohm-cm
Process speed ratio : 1.2 (OPC=1.0)
Color order : Y -> M -> C -> K
1. Only latent image formed by exposing process is developed with toner
2. AC + DC Voltage is being used to develop toner into latent image on OPC because non-contact
developing method is adopted
3. Y, M, C, and K Images are sequentially developed onto OPC and transferred onto Intermediate
Transfer Belt (hereafter ITB) to form a color image on ITB
4. Toner Bottles are used to supply toner into developer compartment
5. Toner level is being sensed to control toner supply from toner bottle to developer
Transfer 1
Multi-pass transfer
Indirect transfer
Transfer voltage : 0.5 ~ 2.0kV (controllable)
Roller diameter : 14mm
Belt resistivity : 10^9 ~ 10^11 ohm-cm
Environment sensing by Y-transfer roller
Transfer unit life : 50K images
1. Developed Image on OPC is transferred onto ITB by T1 Process
2. T1 Voltage is positive which attract toner to ITB
3. 4 times of T1 process is required to make a color image on ITB, which means multi-pass process
4. ITB has a hole as a fiducial mark for timing. Engine control for color image is synchronous with it,
ITB Home Sensing Signal
Service Manual
System Overview
Transfer 2
Indirect transfer
Transfer voltage : 1 ~ 4.0kV (controllable)
Roller diameter : 18.6mm
Belt resistivity : 10^9 ~ 10^11 ohm-cm
Transfer unit life : 50 K images
1. Color image formed on ITB is transferred onto media by T2 process
2. T2 voltage is also positive to get color image moved onto media
3. Toner remained on ITB after T2 process is cleaning by ITB cleaning blade and collected and
4. Transported and retrieved into waste toner box by auger and belt driving system
5. T2 Roll is engaged when color image is being transferred onto media. Otherwise it is disengaged. Clutch is used
for driving T2 Roll engagement and disengagement
Fusing
3 Roll system
-> short warm-up time (45sec)
Post Pressure Roll
1. Color Image on media is melted down and fixed into media by fusing process
Service Manual
System Overview
Main PBA Description

Main Controller PBA
CN5
DEVE_
HOME
CN13
PANEL
CN15
SMPS
CN16
COVER
OPEN
CN4 CN10
DEV_
ITB_
SOL CLUTCH
CN19
HVPS
CN20
CN24
LSU
5V
SWITCH
CN19
DEVE&
ITB
CN2 CN7 CN28

BLDC T2_
FUSER
CLUTCH
CN8
FUSER
CLUTCH
RJ45
USB
CN20
CN24 CN25
REG&
REGI PICKUP
EMPTY CLUTCH
Service Manual
System Overview
Main PBA
EEPROM
64Kbit
Flash
Memory
OSC5
12MHz
OSC2
12MHz
CHORUSm
Main Control
SoC
USB2.0
Device
SDRAM
OSC6
12MHz
Network
Physical Chip
OSC4
25MHz
Service Manual
RJ45
USB
Connector
System Overview
Main PBA Description
1) CHORUSm
CHORUSm involves in itself the functions to control ARM Processor Core and various H/W devices. CHORUSm,
therefore, controls Main PBA and all engine mechanism, processing the print job received from host and enabling the
engine to print image.
Function
Process
0.13um Technology
Package
496 PBGA
CPU Core
ARM 920T - 300MHz
Cache : I-Cache 16KB, D-Cache 16KB
System Bus
32-bit width, 100MHz
SDRAM Controller
32-bit width, 100MHz operation
5 Banks, Up to 128MB Address space per Bank
Programmable Timing to Control SDRAM A.C Characteristics
Support Self Refresh for Data Retention
ROM Controller
32-bit width, 4 Banks, Up to 16MB Address space per Bank
Burst Capability
Programmable Timing per Bank
Service Manual
System Overview
IO Controller
6 Channels, Up to 16MB Address space per Bank
Programmable Timing per Bank
DMA Controller
6 Channels General Purpose DMA
HPVC Controller
Hyper Printer Video Controller
High Performance DMA-based Interface to Printer Engine
Support Dual/Single Beam LSU, LVDS Video Output
Support A3, 1200dpi
UART Controller
5 Channels Indepenent Full Duplex UART
Interrupt Controller
Support 6 External Interrupts
Support 26 Internal Interrupts
Timer Controller
6 System Timers and Watch Dog Timer for S/W Trap
Scanner Controller
300/400/600/1200dpi CIS/CCD Interface
Color/Mono grey image, Binary image scan support
600dpi Color/Mono Copy support
Image Processing for High-End MFP,Digital Copier
MH/MR/MMR CODEC for Fax
Scan image : A4 1200dpi processing
Copy image : A4 600dpi processing
MAC Controller
10/100Mbps
Full IEEE 802.3 compatibility
PPI Controller
IEEE1284 compliant parallel port interface
DMA-Based or Interrupt-Based operation
GEU Controller
Graphic Engine Unit for Banding support of Printer Language
Scan Line Buffer, Polygon Filling
CODEC Controller
2 Channels JBIG Encoding and Decoding
I2C Controller
1 Channel, Operated at max frequency 400kHz
RTC Controller
Engine Controller
LSU Control and Interface Unit
2 Channels STEP Motor Control Unit
8 Channels PWM Control Unit
8 Channels ADC Control Unit
2 Channels DAC Control Unit
Service Manual
System Overview
CHORUSm (Internal Block Diagram)
Service Manual
System Overview
2) System Memory Block

Memory saves program and video data and print jobs received from host. Its volume is 64MB with network function
and 32MB without network function. It has no separate device for extension. SDRAM is used, driven at width of 32-bit
and 100MHz, and controlled by memory controller built in CHORUSm.
3) Flash Memory Block
Flash memory is the space used for saving program. Its volume is 4MB with network function and 2MB without network function. It has no separate device for extension. NOR type flash memory is used and accessed at 32-bit width
burst, being controlled by the ROM controller built in CHORUSm.
4) USB2.0 Device Block
This block supports USB2.0 high speed (480Mbps). ISP1582 of Philips company is used and connected to the IO
Bus of CHORUSm at 16-bit, controlled by IO controller built in CHORUSm. Through this I/O port it receives print job
from host.
5) Network Block
This block has 10/100Mbps wired network function and is controlled by MAC controller built in CHORUSm. It is connected to host through physical layer chip outside, and thus receives print job from host. STE100P is used for physical layer chip.
6) EEPROM Block
System EEPROM is controlled by the I2C controller built in CHORUSm, connected to the other non-volatile memory
on I2C bus. It works at the speed of 400KHz. This system EEPROM contains all drive information and production
information necessary for the operation of printer. Its size is 16k-bit.
7) OPE Control
The panel is driven in the form of PIO by GPIO controller built in CHORUSm. OPE consists of one key and four
monochrome LED, and one dual LED.
8) LSU Control
Laser Scanning Unit is controlled by LSU controller built in CHORUSm. It makes use of all functions such as Polygon
Mirror Motor Control necessary for driving LSU and Synchronized Signal Generation Control, and helps to scan laser
beam on the photosensitive drum to form latent image.
9) BLDC Control
It is controlled by BLDC controller built in CHORUSm. It controls the drive of printer mechanism and helps it to be driven at an equal speed.
10) Sensors Control
GPIO controller built in CHORUSm collects the status of all sensors. According to this status of sensors, it controls
printer mechanism to help normal printing. There are sensors such as Paper Empty Sensor, Registration Sensor and
Developer Home Sensor, etc.
Service Manual
System Overview
11) Clutches Control

GPIO Controller built in CHORUSm controls all clutches, which help printer to do print job normally. There are clutches such as Paper Pick-up Clutch, Registration Clutch, Developer Home Clutch, ITB Clutch, T2 Clutch, Fuser Clutch,
Developer Toner Supply Clutch, etc.
12) PWM Control
PWM Controller built in CHORUSm controls the parts that require PWM for normal printing, such as BLDC drive
speed and HVPS high voltage level, etc.
13) ADC Control
It is controlled by ADC Controller built in CHORUSm, and is used for perception of charged voltage and current, 1st
and 2nd transfer voltage and current, fusing temperature, used-up toner and toner amount, and interior temperature,
etc.
14) DAC Control
It is controlled by DAC Controller built in CHORUSm and used to set standard level of light amount of LSU Laser
Diode.
Service Manual
System Overview
SMPS(Switching Mode Power Supply) PBA

SMPS is consisted of SMPS part which supplies DC power for driving system and AC Heat Control part which supplies
power to Fuser. Standard TYPE III is used.
1) DC Output
Main Controller PBA, OP Panel, BLDC, Sensors, Clutches, Other PBAs
2) AC Output
Fuser Unit(Heat Lamp, Thermostat)
3) Output Voltage
CHANNEL
+5.0V
+24V
+24VF
V_out
+5.0V +/-5%
+24.0V +15%/-10%
+24.0V +15%/-10%
Load
MicroController,
CMOS, LOGIC
LSU
MOTOR, CLUTCH,
HVPS
CON3 To Main PBA
Service Manual
CON2 Fuser AC
CON1 AC Input
System Overview
HVPS(High Voltage Power Supply) PBA

HVPS PBA generates high voltage of charger, supply, T1 and T2 which is supplied to Developer, ensuring optimum condition for image formation. HVPS receives input of 24V and generates high voltage, supplying it to Toner, OPC,
Cartridge, ITB Unit and Transfer Roller.
Service Manual
System Overview
1) Charger Voltage : Charger

Function: voltage that charges OPC surface up to ?500V~ -800V.
Output voltage: -1.0KV ~ -2.0KV DC
3%
Error type: if the voltage fails to be output to Charger Roll, OPC surface will not be charged, and the toner on the
developer roller will be transferred to OPC Drum, printing black paper.
2) 1st Transfer High Voltage : T1(+)
Function: voltage necessary for transferring toner developed on OPC Drum surface onto ITB.
Output voltage: Max +2.0KV
3%(Duty variable, no load)
ERROR type: if T1(+) output fails, the toner on OPC drum will not be transferred to ITB normally and the image will
be blurred.
3) 2nd Transfer High Voltage : T2(+)
Function: voltage used to transfer the toner primarily transferred on ITB again onto paper.
Output voltage: Max +5.0KV
3%(Duty variable, no load)
ERROR type: if T2(+) output fails, the toner on ITB will not be transferred to paper normally and the image will be
blurred.
4) T2 Cleaning Voltage : Clean : T2(-)
Function: prevent reverse side of paper from being dirtied, by recovering the negatively charged toner remaining at
Transfer Roller and sending it onto ITB.
Output voltage: with no feedback control, output fixed voltage(-1300V +/- 15%)
ERROR type: reverse side of paper will be dirtied.
5) Supplying Voltage : Supply AC+DC(-)
Function: voltage that makes toner to develop on the area exposed by LSU by means of potential difference, output
will be the voltage of AC+DC overlapped form.
Output voltage: AC 600V ~ 2000V p-p +/-1.5%
DC -50V ~ -600V DC +/- 3%
ERROR type: 1. if supply is GND, density will be extremely low.
2. if supply is floating (for insecure terminal contact), density will be down so slightly that it is impossible
to make out with naked eyes.
6) Developing Voltage : Deve AC+DC(-)
Function: voltage that supplies toner to Developing Roller
Output voltage: AC 300V ~ 1700Vp-p 1.5% (supply voltage is connected to ZENER Diode 300V)
DC -50V ~ -600V DC +/- 3%
ERROR type: 1. if Deve is GND, density will be extremely down.
2. if Deve is floating (for insecure terminal contact), density will be extremely down.
Service Manual
System Overview
CRUM
In the case of Refill Toner Install
1) Perception of Refill Cartridge (when power is on or the cover is closed)
End of Life / life span data initialization -> judge to be Refill Cartridge
End of Life / life exhausted (simple refill) -> stop printing caused by life exhaustion
2) Operating
It is impossible to control appropriate development parameters, for there s no toner specification data.
It runs with the setting of default development parameter. (Image quality will be degraded, for the lack of appropriate
respond to the change of time and environment.)
3) Service Response
It is possible to response appropriately, for the information of cartridge life is saved at Back Up Area.
Process after CRU life expiration

1) Record the information of End of Life.
2) Copy the information of Operating Area into Back up Area.
3) Write-Protect Back up Area.
4) Clear some information of Operation Area.
-> Supplier/Model Name/MFC date/Serial Number (Manufacture Information)
-> Let cartridge refiller initialize manufacture information and life span information.
Service Manual
System Overview
CRUM Position
Cap
Agitator
Washer
Bottle
Cap- CRUM
Agitator
Seal
CRUM
Coupling
Service Manual
System Overview
General Description
This chapter is the product specification for the printer. The Phaser 6110 is a Color Laser Printer. The Phaser 6110
can be expanded to multi functional printer (MFP). Phaser 6110 is developed for two target users.
Those are small office users who sometimes need color printouts, and medium business users who mainly use B/W
printouts. The main product concept is the world smallest and lightest color laser printer. This model has 16ppm B/W
print-speed and 4ppm color print-speed, 2400 x 600 dpi class (optical 600 x 600 dpi) color laser printer.
Controller
-The video controller board is located on the right side of the printer.
-Basic Memory is 32 Mbytes SDRAM.
-Field F/W upgradeable FLASH ROM firmware for controller, 1024 byte EEPROM
-Printing Resolution :
Native 600 x 600 dpi standard
Resolution can be enhanced up to 2400 x 600 dpi class, 1200 x 600 dpi (default), 600 x 600 dpi
Processor
CHORUSm (300Mhz), Proprietary SOC
Printer Language Emulations

SPL-Color
Memory
The controller has 32 MB SDRAM and 4 MB flash ROM on Board.
Service Manual
System Overview
Interfaces
The system supports the following standard interfaces:
One USB port
- USB v.2.0 compliant
- Color-coded to meet WHQL requirements, connector must be Pantone 426C
One 10/100 BaseT network connector
- The printer supports an internal Network Interface that can be installed pre-configured on the video
controller board at the factory. This supports all of the major Network Operating Systems such as the Novell
NetWare, TCP/IP, etc. Details of the network specification will be provided separately.
Control Panel
No LCD, 1 key and 5LEDs.
Periodic Replacing Parts

Xerox shall specify parts requiring replacement and the frequency of replacement. The parts identified may be
deemed customer replaceable parts. Periodic replacement parts shall be recommended as follows
Toner Cartridge
1K(Color), 2K (Mono) pages
User replaceable
Imaging Kit
44K Images
User replaceable
Fusing Unit
71K page (28.6K Color/42.9K Mono)
Field replaceable
Transfer Roller
100K pages
Field replaceable
Waste Toner Container
5000 Images (3636 Color/1364 Mono)
User replaceable
Pick up
100K(Color/Mono) pages
Field replaceable
** Based on Printing Volume ratio of 40% Color and 60% B/W
Power Switch
The Switch is located at rear-side of printer and must be marked to indicate on and off.
Operator Panel
LCD: None
KEY: 1 key (Stop)
LED: 5 LEDs (C, M, Y, K Toner, Status)
Service Manual
System Overview
Sensor
Paper empty (Cassette)
CRUMS
The Phaser 6110 engine will be equipped with electronics that can read and write data into NVRAMs otherwise
known as CRUMs that reside within 1) C, M, Y, K Toner cartridges and 2) Imaging kit(Developer, OPC, ITB). The CRUM
has a company ID, and electronics logo.
The toner CRUM also identifies the type of toner cartridge (Standard or High Capacity). The CRUMs contain fixed data
such as the low warning point, specified life point, and hard stop point (on toner, not on IBT unit) and also store the current life count (pages count, pixels count, images count) and % of usage (gas gauge) data.
LOW / OUT Behavior for consumables

The consumable low and out behavior on Phaser 6110 engine is specified by SEC.
FP
message
Device for life end

detection
Law(90%)
Life(100%)
Hard stop
Reset to 0
Toner
CRUM
Yes
Yes
Yes(115%)
No
Imaging Kit
CRUM
Yes
Yes
No
No
Fuser
No
Yes
Yes
No
Yes
T2 Roller
No
Yes
Yes
No
Yes
Pick-up
No
No
No
No
No
Service Manual
S/W Structure and Descriptions
Architecture
The belt CRUM interface board is a transmission belt CRUM interface board of the photoelectric Dry Color Laser
Printer, mounted on the printer body, making it possible to physically combine the body and the belt CRUM board.
Printer Driver
Language Monitor
Status Monitor
Printer F/W
Network Card F/W
Language Monitor
Language Monitor is a part of the Printer Driver and the Windows Spool System. The main roll of the Language
Monitor is that sends a job start message to the Status Monitor. Therefore the Status Monitor
can start polling to get the printer status.
The second roll is that sends the job information such as User ID and Job ID to the Status Monitor and the Printer
F/W. Hence the Status Monitor can stop polling because the Printer F/W informs the Status Monitor that printing
job is complete.
Status Monitor
Status Monitor has no user interface. It shows only HTML help when any error occurs during printing jobs.
Service Manual
Network Interface
Printer Driver
Language
Monitor
Printer Data
User ID + Job ID
+
Printer Data
Printer Server
(Kernel / NPC)
Printer Name
Port Name
User ID
Job ID
Printer Server IP Addr
SNMP
Printer Server
(Kernel / NPC)
Job ID
Request Printer Status

Printer Status
Status Monitor
Request Job Status

Job Table
Status Monitor Data Flow
After polling is started, Status Monitor has to know when it stops the polling. For this reason, the Network
Printer Server should inform of completing job when the printing job is finished.
When Status Monitor requests a job status, the Printer Server returns the job table that contains user id, job
id, and job status (printing or complete or canceled).
Printer Driver <-> Status Monitor

The Printer Driver and the Status Monitor can set/get some data to the system registry to share the Status Monitor
information such as the polling interval.
When the user wants to set the option of the Status Monitor manually, he or she can set it using the Printer Driver
User Interface. So, if the user set option that the Status Monitor is disabled, the Status Monitor cans show HTML
Help to the user although the error has occurred while printing.
Set option value

enable/disable
or
polling interval
Set last error status
System
Registry
Status Monitor
Get option value
enable/disable
or
polling interval
Service Manual
Printer Driver
Get last error status
System F/W Flow

Input
Process
Photo Sensor ( intensity
of radiation )
Output
PWM
LED
LED PWM Output
Auto color
registration
sensor
ADC
density
Density pattern
printing
LED PWM decision
PWM
Comparator Threshold
voltage PWM decision
Comparator
ACR data
Color Registration measure
LPEC2
LSU
Auto Color Registration

pattern printing
ACR module
H Sync.
Video data
Color Registration adjustment

Page Sync. modify
LSU
Line Sync. modify

LSU
temperat
ure
sensor
Video Clock Freq.

modify
ADC
P Sync.
L Sync.
Video signal
generator
clock
PWM
LSU temperature control
SMPS Fan
Service Manual
Alarm Shortage
90 ~ 100 %
100 ~ 110 %
110 %~
Toner (C,M,Y,K)
Ready Yellow Toner Low
Replace Yellow Toner
Yellow Toner Empty
Transfer Belt
Replace Transfer Belt Soon
Replace Transfer Belt
Fuser
Replace Fuser Soon
Replace Fuser
Pickup Rollers
Replace MP Pick-Roller
(MP/Tray1/Tray2)
Error status
1. Missing/Invalid Consumables
Install Cyan (Magenta, Yellow, Black) Toner
Install Transfer Belt
Invalid Cyan (Magenta, Yellow, Black) Toner
Invalid Transfer Belt
2. Paper Empty/Mismatch
Paper Empty In MP(Tray1, Tray2)
Load A4 In MP(Tray1, Tray2)
3. Paper JAM
Jam 0 In MP(Tray1, Tray2)
Jam Inside Printer
Jam In Exit Area
4. Cover
Cover Open : Message toggles between
Cover Open and Install Transfer Belt
SCF Cove Open
5. Service Call : Unrecoverable Error
Engine LSU Error
Main Motor Error / Dev. Motor Error
Engine Fuser Over(Low) Heat Error
Rear Fan Error / Left Fan Error / SMPS Fan Error
6. Others
Memory Overflow Error
Ready IP Conflict
Service Manual
CRUM Overview
- Stands for Customer Replaceable Unit Monitor
- EEPROM is used for CRUM Memory.
- CRUM stores various information on consumables
(including consumables life).
CRUM stores the following information

Model Name
Supplier ID
Serial Number
Company ID
MFG Date
Capacity
Page Count
- Toner Cartridge and Transfer Belt
- Indicates how many pages are printed by using the consumable
Dot Count
- Toner Cartridge Only
- Indicates how many dots are printed by using the toner cartridge
FW Upgrade
Via USB or Network (SWS/SWAS)
You can upgrade F/W via USB or Network whenever the printer is Ready
Via Using F/W Download Mode :
Step 1) Power on while pressing the Online Key
Step 2) Press Online Key one more time if required.
Step 3) Download F/W via USB
Service Manual
Initailize Flow
Service Manual
Service Manual
Alignment and Adjustments
This chapter describes some of the main service procedures including:

Using the EDC mode; Clearing paper jam and test patterns.
Much of this chapter is also included in the user's guide.
Control Panel
Overview
- The Phaser 6110 does not have LCD panel which is used in other color model printers. On the contrary
to other models of color printers, they show the status of the printer only with their LEDs.
- The Phaser 6110 has 1 key and 5 LEDs. The User Interface module handles the processing of the
Key Press and Led control at different states of the machine.
Architecture
KEY (1 key): Stop key
LED (6 LEDs):
4 LED for CMYK toners : toner-low(cyan, magenta, yellow, black) LEDs
1 LED for status : ready (green) or error(red) status LED (two color LED)
Stop
Status
Data and Control Flow

User interface (panel) is made up of
- KEY input detection & process
- LED control
The initial process to use the panel checks registers values of key and LED.
If user input key value, the operation to be defined by key value is processed and the LED operation to be
defined by printer status is controlled.
Service Manual
Function
KEY Function
There is one key present. The Stop key.
If users input key value, the key input is transferred via GIP (General Input Port) and the operation to be
defined by key value is processed.
Functions
Stop key function is made up of
- Demo page/Configuration sheet printing function
- Job cancels function
- Start manual feeding function
- Firmware downloads mode function
Detail Description
KEY input detection & process order
1) User KEY input
2) KEY input detection
: If the key input is detected when the key input check per timer tick 10ms, The 10ms interrupt service
routine sends the key detection event to panel task.
3) KEY input process
Stop key input process
: After the panel task is received the Stop key detection event, it checks the engine error status two times
and process the operation to be defined by key value.
- Demo page/Configuration sheet function
This button will have multiple functions when the printer is in idle state.
Demo page printing
Press and hold this button for about 2 seconds until the control panel lights blink slowly to print a
demo page.
Configuration sheet printing
Press and hold this button for about 6 seconds until the control panel lights blink rapidly to print a configuration sheet.
- Job cancels function
When the printer is printing an active printing job, press and holds this button until the control panel
lights blink to cancel a job the printer is currently except the manual job.
- Start manual feeding function
When you select manual feed for paper source, press this button each time you feed a sheet of paper
manually.
The application of manual feeding function in Phaser 6110 will be determined
Service Manual
- Firmware downloads mode function

Turn on the printer at the same time that the button is pressed.
If all LEDs scroll, release the button and download the firmware ROM file via USB port
Black only key input process
: After the panel task is received the Black only key detection event, it changes printer mode to Black only
mode and notifies driver that the printer mode is changed to Black only mode. If printer mode is Black
only mode, driver makes printer image by only mono excepting color.
LED Function
There are five LEDs present. Status led indicate the error/online status of the printer in idle mode. In error
Functions
Detail Description
LED control order
Service Manual
LED behavior
Status LED
(Green/Red)
Black-only
LED
Toner-low
(CMYK)LEDs
Status
Green LED ON
N/A
N/A
Green LEDS
LOWLY BLINK
N/A
N/A
Green LED
FAST BLINK
N/A
N/A
Printing the page.
Red LED BLINK
N/A
N/A

printing
Red LED ON
N/A
N/A
Out of paper
Red LED ON
N/A
N/A
Cover open
Red LED ON
N/A
N/A
Paper jam
Green/Red BLINK
BLINK
CMYK BLINK
N/A
N/A
Toner-low(black) ON
N/A
N/A
Toner-low(cyan) ON
N/A
N/A
N/A
N/A
N/A
ON
N/A

Service Error
Fuser Error
Scanner Error
(=LSU Error)
Service Manual
LED operation
Open Fuser Error

No Heat Error

Over Heat Error

P Motor Error

H Sync Error


Line number
LED operation
start & end
All LEDs(Toner low LEDs, Status(Red) LED) turn ON for approximately 2 seconds and then All LEDs turn OFF for approximately 3 seconds.
Service Manual
LED Function
There are five LEDs present. Status led indicate the error/online status of the printer in idle mode. In error
Functions
Detail Description
LED control order
Service Manual
LED behavior
Status LED
(Green/Red)
Black-only
LED
Toner-low
(CMYK)LEDs
Status
Green LED ON
N/A
N/A
Green LEDS
LOWLY BLINK
N/A
N/A
Green LED
FAST BLINK
N/A
N/A
Printing the page.
Red LED BLINK
N/A
N/A

printing
Red LED ON
N/A
N/A
Out of paper
N/A
Cover open
Red LED ON
Red LED ON
N/A
N/A
Paper jam
Green/Red BLINK
BLINK
CMYK BLINK
N/A
N/A
Toner-low(black) ON
N/A
N/A
Toner-low(cyan) ON
N/A
N/A
N/A
N/A
N/A
ON
N/A

Service Error
Fuser Error
Scanner Error
(=LSU Error)
Service Manual
LED operation
Open Fuser Error

No Heat Error

Over Heat Error

P Motor Error

H Sync Error


Line number
LED operation
start & end
All LEDs(Toner low LEDs, Status(Red) LED) turn ON for approximately 2 seconds and then All LEDs turn OFF for approximately 3 seconds.
Service Manual
Error Message
LED status legend
LED pattern



representative.
Service Manual
Section 11 Component Locator
Understanding the Control Panel
Status
LED
Toner
LEDs
lights red
each LED
lights red
The each toner cartridge is

totally exhausted.
wrong.
lights red
each LED
blinks red
in a
repeated
order

totally exhausted.
wrong.
Description
NOTE: All printing errors will be appear in the Status Monitor

program window.
Stop(
) button
Function
LEDs
Status
LED
Toner
LEDs
Description
lights
green
All LEDs
off
The printer is ready to print.
slowly
blinks
green
All LEDs
off
The printer is receiving data from

the computer.
fast blinks
green
All LEDs
off
The printer is printing data.
lights red
All LEDs
off
The printer is experiencing an

error, such as jammed paper,
open cover, empty paper, open
waste toner container, or full
waste toner container.
The printer is experiencing a
service required error, such as
LSU error, fuser error, or ITB
error. Contact your sales or
service representative.
lights
green
each LED
blinks red
The each colour toner cartridge is

near the end of its life.
blinks red
each LED
lights red
The each colour toner cartridge is

empty.
Introduction
Description
Printing
demo page
In Ready mode, press and hold this button

for about 2 seconds until the
LED
blinks fast, and release.
Printing
configuration
sheets
In Ready mode, press and hold this button

for about 5 seconds until the
LED
blinks fast, and release.
Canceling
print job
Press this button during printing. The red

LED blinks while the print job is cleared
from both the printer and the computer,
and then the printer returns to Ready
mode. This may take some time depending
on the size of the print job.
Rear View
Printer Components
These are the main components of your printer. Note that all
illustrations on this Users Guide are from the Phaser 6110N
and that some parts may be different from your printer.
Rear Cover
(Open to clear
paper jams.)
Front View
Output Tray
(Face down)
Top Cover
(Open to clear
paper jams.)
Output
Support
Front Cover
(Open to access the

toner cartridges and
imaging unit.)
Power
Switch
Network
Port*
USB Port Power

Receptacle
* Only the Phaser 6110N comes with a network port.
Toner
Cartridges
Tray
(150-sheet
paper feeder)
Control Panel
(See 1.3.)
Handle
(Use to lift
the printer.)
NOTE: The surface of the output tray may become hot if you print
a large number of pages at once. Please make sure that you dont
touch the surface, and prevent children from approaching it.
Introduction
System Overview
System Overview
This chapter describes the functions and operating principles of the main components.
System Structure
Main Parts of System
Service Manual
Section 12 Reference Library
Precautions
1.3 ESD Precautions

Certain semiconductor devices can be easily damaged by static electricity. Such components are commonly called
Electrostatically Sensitive (ES) Devices, or ESDs. Examples of typical ESDs are: integrated circuits, some field
effect transistors, and semiconductor chip components.
The techniques outlined below should be followed to help reduce the incidence of component damage caused by
static electricity.
Caution >>Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
1. Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain off any
electrostatic charge on your body by touching a known earth ground. Alternatively, employ a commercially available wrist strap device, which should be removed for your personal safety reasons prior to applying power to the
unit under test.
2. After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface, such as
aluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity of the assembly.
3. Use only a grounded tip soldering iron to solder or desolder ESDs.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can
generate electrical charges sufficient to damage ESDs.
5. Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges sufficient to damage ESDs.
6. Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most
replacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a comparable conductive material.
7. Immediately before removing the protective shorting material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.
8. Maintain continuous electrical contact between the ESD and the assembly into which it will be installed, until completely plugged or soldered into the circuit.
9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushing
together of clothing fabric and lifting ones foot from a carpeted floor, can generate static electricity sufficient to
damage an ESD.
1.4 Super Capacitor or Lithium Battery Precautions

1. Exercise caution when replacing a super capacitor or Lithium battery. There could be a danger of explosion and
subsequent operator injury and/or equipment damage if incorrectly installed.
2. Be sure to replace the battery with the same or equivalent type recommended by the manufacturer.
3. Super capacitor or Lithium batteries contain toxic substances and should not be opened, crushed, or burned for
disposal.
4. Dispose of used batteries according to the manufactures instructions.
Service Manual
SERVICE BULLETIN
PRODUCT: Phaser 6110, Phaser 6110MFP (1)
T6140-10-19
SUBJECT:
Fuser Vapour
OPERATIONAL GROUPS: Canada, DMO-W, NARs, XE,

XING
PROBLEM
SURF, or Surface Rapid Fusing technology can produce a visible vapour
under certain conditions of ambient low humidity, cooler office
temperatures, or with paper with higher moisture content.
SOLUTION
Inform customer that the condition is not hazardous and is a characteristic
of a quick fuse operation in some circumstances.
Bulletin Contact: Ron Fabretti
Intelnet: 8-225-7826
Date: Oct 5, 2006
e-mail: [email protected]
Page 1 of 1

Xerox Phaser 6110 - Service Manual

Uploaded by

Document Informationclick to expand document informationService Manual Xerox Phaser 6110

Document Informationclick to expand document information

Copyright:

Available Formats

Xerox Phaser 6110 - Service Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Xerox Phaser 6110 - Service Manual

Uploaded by

Copyright:

Available Formats

Publication Information for Xerox,

CAUTION - INVISIBLE LASER RADIATION

Caution for safety

Electric Shock and Fire Safety Precautions

Assembly / Disassembly Precautions

Disregarding this warning may cause bodily injury

Section 1 Service Call Procedures

Disassembly and Reassembly

Parts for Maintenance and Repair

Toner Cartridge (Black)

intial (1,500 pages@5% coverage)

Toner Cartridge (Color: C/M/Y)

intial (700 pages@5% coverage)

Waste toner container

5K image or 1.25K pages

20K pages (Black)

ITB Unit(Image Transfer Unit)

Black : (60K pages@5% coverage)

100,000 pages (B/W) Color(50,000 pages)

Menu-Setup - Maintenance - Check other - (Select a desired part) - Reset

Section 2 Machine Declared Faults

Alignment and Adjustmens

Possible Problem and Solution

The lighting toner cartridge is empty.

A paper jam has occurred. To solve the problem.

No Fuser drive due to overheated gear(s)

Defective motor operation

Section 3 User Declared Faults

Solving Print Quality Problems

Light or faded print

If generally rounded, faded areas occur randomly on the page:

If black vertical streaks appear on the page:

Clean the inside of the printer.

Ensure that the paper is loaded properly.

Ensure that the paper is loaded properly.

Check for leaking toner. Clean the inside of the printer.

The toner cartridge may not be installed properly.

If horizontally aligned color or black streaks or smears appear:

Major Problems Trouble shooting

Vertical White Line

Dark Image or black

Major Problems Trouble shooting

Vertical White Line

Dark Image or black

Alignment and Adjustmens

Periodic Defective Image

White and Black Spots

Black Spot and line and Periodic Band

Periodic Band by little difference of density

White Spot, Horizontal black band

Ghost, Damaged Image by abnormal tranfer

Ghost, Damaged Image by abnormal tranfer

Black Spots or Vertical Black Band

Solving General Printing Problems

Common Windows Problems

Possible Cause and Solution

"General Protection Fault",

"Fail To Print", "A printer timeout