33 Lights PDF

A350
TECHNICAL TRAINING MANUAL

MAINTENANCE COURSE - T1+T2 - RR Trent XWB
Lights
This document must be used for training purposes only
Under no circumstances should this document be used as a reference
It will not be updated.
All rights reserved

No part of this manual may be reproduced in any form,
by photostat, microfilm, retrieval system, or any other means,
without the prior written permission of AIRBUS S.A.S.
AIRBUS Environmental Recommendation

Please consider your environmental responsability before printing this document.
A350 TECHNICAL TRAINING MANUAL
LIGHTS
V1813401 - V01T0M0
Cockpit Lighting System Description (2) . . . . . . . . . . . . . . . . . . . . . . 2

Cabin Lighting System Description (2/3) . . . . . . . . . . . . . . . . . . . . . 30
Emergency Lighting System Description (2/3) . . . . . . . . . . . . . . . . . 54
Cargo and Service Compartment Lighting (2) . . . . . . . . . . . . . . . . . . 72
Exterior Lighting System Description (2/3) . . . . . . . . . . . . . . . . . . . . 86
Lighting System Maintenance (2/3) . . . . . . . . . . . . . . . . . . . . . . . . . 106
Lighting System Control and Indicating (2/3) . . . . . . . . . . . . . . . . . 116

33 - Lights
TABLE OF CONTENTS
Oct 21, 2013

Page 1
COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

Cockpit General Illumination
V1813401 - V01T0M0 - VM33D1COCKT2301
The LEDs are used for all the cockpit general illumination.

33 - Lights
Oct 11, 2013

Page 2
V1813401 - V01T0M0 - VM33D1COCKT2301
COCKPIT GENERAL ILLUMINATION

33 - Lights
Oct 11, 2013

Page 3

Ambient Lighting
General ambient lighting
V1813401 - V01T0M0 - VM33D1COCKT2301
The general ambient lighting can illuminate all the cockpit and gives
the flight crew members the correct lighting to move in the cockpit.
It includes CAPT and F/O dome lights, which are identical.
The dome lights are controlled by the DOME LT rotary knob or
through a switch installed near the cockpit door.
The DOME LT rotary knob (installed on the CKPT LT section of the
center pedestal) lets the flight crew members adjust the brightness
level of the dome lights. This rotary knob has two positions: OFF and
STORM.
A switch installed near the cockpit door is used to switch on or off
the dome lights. When the dome lights are switched on via this switch,
they are set to the low brightness level (5% of the full brightness).

33 - Lights
Oct 11, 2013

Page 4
V1813401 - V01T0M0 - VM33D1COCKT2301
AMBIENT LIGHTING - GENERAL AMBIENT LIGHTING

33 - Lights
Oct 11, 2013

Page 5

Ambient Lighting (continued)
Storm function
V1813401 - V01T0M0 - VM33D1COCKT2301
The DOME LT rotary knob has a STORM position. This position is

used in storm conditions to keep a high level of luminosity in the
cockpit.
When the storm function is selected, the lights that follow are set at
full brightness:
- Dome lights
- Main instrument-panel lights
- Center pedestal light
- Outer VU lights.

33 - Lights
Oct 11, 2013

Page 6
V1813401 - V01T0M0 - VM33D1COCKT2301
AMBIENT LIGHTING - STORM FUNCTION

33 - Lights
Oct 11, 2013

Page 7

Ambient Lighting (continued)
Pilot individual working-area lighting
V1813401 - V01T0M0 - VM33D1COCKT2301
The CAPT and F/O individual working-area lighting includes:

- The console lights (CAPT and F/O). They can be used to illuminate
the cockpit sides during maintenance or in storm conditions (in
addition to the storm function).
- The left and right rudder-pedals lights. They are used to illuminate
the cockpit floor.
The CAPT and F/O CONSOLE LT rotary knobs let the flight crew
to adjust the intensity of the lights, from the OFF to the Bright (BRT)
position.
The left and right rudder-pedals lights come on when the PEDALS
LT control switch is set to the ON position.

33 - Lights
Oct 11, 2013

Page 8
V1813401 - V01T0M0 - VM33D1COCKT2301
AMBIENT LIGHTING - PILOT INDIVIDUAL WORKING-AREA LIGHTING

33 - Lights
Oct 11, 2013

Page 9

Instrument Panel Lighting
Main instrument-panel lighting
V1813401 - V01T0M0 - VM33D1COCKT2301
The main instrument-panel lighting includes four LED lighting

modules.
The two center lighting modules illuminates:
- The exchange area (area above throttle) on the pedestal.
The left lighting module illuminates:
- The panel between CAPT inner and upper Display Units (DUs)
- The panel on the left side of lower DU.
The right lighting module illuminates:
- The panel between F/O inner and upper DUs
- The panel on the right side of lower DU.
On the pedestal, the FLOOD LT rotary knob lets the flight crew
members adjust the intensity of the lights from the OFF to the BRT
position.
In addition, when the DOME LT rotary knob is set to the STORM
position, the main instrument panel lights are set to full brightness.

33 - Lights
Oct 11, 2013

Page 10
V1813401 - V01T0M0 - VM33D1COCKT2301
INSTRUMENT PANEL LIGHTING - MAIN INSTRUMENT-PANEL LIGHTING

33 - Lights
Oct 11, 2013

Page 11

Instrument Panel Lighting (continued)
Pedestal light
V1813401 - V01T0M0 - VM33D1COCKT2301
The pedestal light gives the flight crew members a satisfactory view
of the related area.
This light is installed on the overhead panel.
members adjust the intensity of the pedestal light from the OFF to the
BRT position.
position, the pedestal light is set to full brightness.

33 - Lights
Oct 11, 2013

Page 12
V1813401 - V01T0M0 - VM33D1COCKT2301
INSTRUMENT PANEL LIGHTING - PEDESTAL LIGHT

33 - Lights
Oct 11, 2013

Page 13

Instrument Panel Lighting (continued)
Outer VU lights
V1813401 - V01T0M0 - VM33D1COCKT2301
The outer VU light gives the flight crew members a satisfactory view
of the annunciator lights and controls on the CAPT and F/O outer
panels.
These lights are installed below the glareshield.
members adjust the intensity of the outer VU lights from the OFF to
the BRT position.
position, these lights are set to full brightness.

33 - Lights
Oct 11, 2013

Page 14
V1813401 - V01T0M0 - VM33D1COCKT2301
INSTRUMENT PANEL LIGHTING - OUTER VU LIGHTS

33 - Lights
Oct 11, 2013

Page 15

Instrument and Panel Integrated Lighting
The instrument and panel integrated lighting lets the crew read the
indications on the panels and instruments during night flights or flights
in stormy weather conditions. The pilots can adjust the lighting level of
all lighted panels and Liquid Crystal Display (LCD) backlighting in the
cockpit through the rotary knobs.
To do this function, the system uses:
- LEDs
- Rotary knobs
- A dimming control unit.
Dimming Control Unit

The dimming control unit receives orders from the rotary knobs to
control the integrated lighting level of the control panels and
equipment.
The dimming control unit is installed in the avionics compartment
under the cockpit floor.
LEDs
V1813401 - V01T0M0 - VM33D1COCKT2301
The LEDs are used for the integrated lighting of the cockpit panels
that follow:
- Integrated Control Panels (ICPs)
- VU control panels
- Flight Control Unit (FCU)
- Lighted equipment (e.g.: Radio and Audio Management Panels
(RMPs), Integrated Standby Instrument System (ISIS), etc.).
The lighted plates let the crew read the indications on the panels.
Rotary knobs
The pilots can adjust the lighting level of all the lighted panels and
LCD backlighting in the cockpit from three controls:
- An INTEG LT rotary knob installed on the center pedestal, which
is used to adjust the intensity of the integrated lighting for the VMs,
VUs and lighted equipments.
- A right glareshield rotary knob (installed below the FCU), which is
used to adjust the intensity of the FCU lighted identification-plates
and the P/BSW legends on the glareshield.
- A left glareshield rotary knob (installed below the FCU), which is
used to adjust the intensity of the FCU display.
33 - Lights
Oct 11, 2013

Page 16
V1813401 - V01T0M0 - VM33D1COCKT2301
INSTRUMENT AND PANEL INTEGRATED LIGHTING - LEDS ... DIMMING CONTROL UNIT
33 - Lights
Oct 11, 2013

Page 17

Annunciator Light Test and Dimming System
V1813401 - V01T0M0 - VM33D1COCKT2301
The annunciator light test and dimming system controls the brightness
level and does the test of all the annunciator lights installed in the cockpit.
The pilots can change the lighting level (dim or bright) of all the
annunciator P/BSWs of the cockpit in the VMs, VUs and lighted
equipment through the ANN LT control switch on the overhead panel.
The TEST position of the ANN LT control switch is used to do a visual
check of all the annunciator lighting for correct operation. The applied
illumination level is bright.
The annunciator light test and dimming system does not comport any
equipment. It relies only on wiring and some relays to interconnect the
ANN LT control and the various equipment or VU
annunciators/pushbuttons.
The DIM/BRIGHT/TEST toggle switch is directly wired:
- Via dedicated relays, to cockpit lighted equipment, VU
annunciators/pushbuttons and ICP without Controller Area Network
(CAN) for the command of BRT/DIM level and test function,
- Via CAN buses to ICP equipped with CAN.

33 - Lights
Oct 11, 2013

Page 18
V1813401 - V01T0M0 - VM33D1COCKT2301
ANNUNCIATOR LIGHT TEST AND DIMMING SYSTEM

33 - Lights
Oct 11, 2013

Page 19

Utility Lights
V1813401 - V01T0M0 - VM33D1COCKT2301
Pilot utility lights

The pilot utility lights are:
- The sliding table lights
- The map lights
- The reading lights.
Sliding table lights
The CAPT sliding-table lights are installed below the glareshield in
front of the CAPT.
The F/O sliding-table lights are installed below the glareshield in front
of the F/O.
The sliding table lights illuminate the keyboard and documents on the
sliding table.
Two potentiometers (one for CAPT and one for F/O) adjust the
intensity of the light.
Map lights
The map lights are installed in the linings of the lateral windows.
The two MAP LT rotary knobs (one for CAPT and one for F/O) let
the flight crew members adjust the intensity of the lights, from the
OFF to the BRT position.
The map lights are Line Replaceable Units (LRUs). They are
interchangeable with Third and Fourth Occupant reading lights.
Reading lights
The CAPT and F/O reading lights are installed in the top left and right
corners of the windshields.
A potentiometer (top control ring) included in each light controls the
intensity of the light.
A diaphragm (bottom control ring) included in each light adjusts the
beam dimension.
Note that the beam direction of the reading lights is adjustable to
illuminate the lateral console, side stick area, seat positions, sliding
table and a part of the pedestal.
33 - Lights
Oct 11, 2013

Page 20
V1813401 - V01T0M0 - VM33D1COCKT2301
UTILITY LIGHTS - PILOT UTILITY LIGHTS

33 - Lights
Oct 11, 2013

Page 21

Utility Lights (continued)
Eye reference light
V1813401 - V01T0M0 - VM33D1COCKT2301
The eye reference light is installed on the central strut between the
two windshields.
On the INT LT section of the overhead panel, the STBY COMPASS
and EYE REF control switch controls the eye reference lighting to
help the flight crew members adjust the position of their seat.

33 - Lights
Oct 11, 2013

Page 22
V1813401 - V01T0M0 - VM33D1COCKT2301
UTILITY LIGHTS - EYE REFERENCE LIGHT

33 - Lights
Oct 11, 2013

Page 23

Occupant utility lights
V1813401 - V01T0M0 - VM33D1COCKT2301
One reading light and one console light for the Third Occupant
The console light for the Third Occupant is installed in the ceiling,
between the overhead panel and the dome light.
The reading light for the Third Occupant is installed in the ceiling,
behind the dome light.
Two rotary knobs in the Third Occupant area are used to adjust the
intensity of the lights from the OFF to the BRT position.
One reading light for the Fourth Occupant
The reading light for the Fourth Occupant is installed in the lining of
the left lateral part, behind the CAPT seat.
A rotary knob in the Fourth Occupant area is used to adjust the
intensity of the light from the OFF to the BRT position.

33 - Lights
Oct 11, 2013

Page 24
V1813401 - V01T0M0 - VM33D1COCKT2301
UTILITY LIGHTS - OCCUPANT UTILITY LIGHTS

33 - Lights
Oct 11, 2013

Page 25

Coat stowage lights
V1813401 - V01T0M0 - VM33D1COCKT2301
The coat stowage lights are installed in the linings of the coat stowage
(one at the top and one at the bottom).
The COAT STWG LT control switch lets the flight crew members
control the two lights of the coat stowage.

33 - Lights
Oct 11, 2013

Page 26
V1813401 - V01T0M0 - VM33D1COCKT2301
UTILITY LIGHTS - COAT STOWAGE LIGHTS

33 - Lights
Oct 11, 2013

Page 27

Service power outlets
V1813401 - V01T0M0 - VM33D1COCKT2301
Two service power outlets (115VAC and 28VDC) are installed near
the Fourth Occupant console. These outlets can be used for servicing
tasks (to clean the cockpit by vacuum for example).

33 - Lights
Oct 11, 2013

Page 28
V1813401 - V01T0M0 - VM33D1COCKT2301
UTILITY LIGHTS - SERVICE POWER OUTLETS

33 - Lights
Oct 11, 2013

Page 29
CABIN LIGHTING SYSTEM DESCRIPTION (2/3)

Cabin Lighting
The cabin lighting units includes:
- The ceiling light
- The sidewall light
- The ceiling recess light
- The handrail light (optional).
Note 1: all the cabin lighting elements use LED technology.
Note 2: these cabin lights supply lighting through reflection on the
surfaces.
The optional handrail lights are installed on the grip rails of the center
and lateral OHSCs. They illuminate the grip rails of the OHSCs and
the seat row numbering.
Note that the FAP is the primary control for the application lights
through the FAP/Lights page.
V1813401 - V01T0M0 - VM33D2CABIN3001
General lighting
The general illumination inside the cabin is done by the lighting units
that follow:
- The ceiling light
- The sidewall light.
The ceiling lights are installed behind a cover of the lateral Overhead
Stowage Compartments (OHSCs).
The sidewall lights illuminate the side of the cabin in an area which
does not receive illumination from the ceiling light.
The FAP is the primary control for the general lighting through the
FAP/Lights page.
Application lights
The application lights include the lighting units that follow:
- The ceiling recess light
- The handrail light.
The application lights are used to highlight and accentuate the different
areas of the cabin and to underline the interior design.
The ceiling recess lights are installed above the center OHSCs to
illuminate the recess of the ceiling.

33 - Lights
Oct 11, 2013

Page 30
V1813401 - V01T0M0 - VM33D2CABIN3001
CABIN LIGHTING - GENERAL LIGHTING & APPLICATION LIGHTS

33 - Lights
Oct 11, 2013

Page 31

Entrance Areas
V1813401 - V01T0M0 - VM33D2CABIN3001
The spotlights illuminate the entrance areas and the cross aisle. The
primary control of the spotlights is done through FAPs (and optionally
the Additional Attendant Panels (AAP)).
Note that most of the spotlights contain a separate emergency light.
An optional dome light can be installed at door 2 area.
Note that the dome light is part of the application lights.
The direct ceiling lights illuminate the entrance areas at door 1 and 4.

33 - Lights
Oct 11, 2013

Page 32
V1813401 - V01T0M0 - VM33D2CABIN3001
ENTRANCE AREAS
33 - Lights
Oct 11, 2013

Page 33

Passengers and Attendant Lights
V1813401 - V01T0M0 - VM33D2CABIN3001
The passenger LED reading lights on the Passenger Service Unit (PSU)
can be set to the on or off position individually from:
- The related P/BSW on the PSU
- The P/BSW on Passenger Control Unit (PCU), installed on the passenger
seat, through the IFE system.
In addition, the R/L On and R/L Off control keys on the FAP/Lights page
set all the passenger LED reading lights to the on or off position (on
ground only).
The attendant work lights are installed in the attendant seat areas and in
special working areas. The related P/BSW sets its attendant work light
to the on or off position.

33 - Lights
Oct 11, 2013

Page 34
V1813401 - V01T0M0 - VM33D2CABIN3001
PASSENGERS AND ATTENDANT LIGHTS

33 - Lights
Oct 11, 2013

Page 35
V1813401 - V01T0M0 - VM33D2CABIN3001
Standalone Signs
There are different standalone lighted signs:
- The No Smoking (NS) signs
- The Fasten Seat Belts (FSB) signs
- The Return to Seat (RTS) signs
- The lavatory occupied signs
- The no Portable Electronic Devices (PEDs) signs (optional).
There is a vacant and an occupied indicator in the cockpit, for the lavatory
of the left door 1 area.
The NS, FSB and RTS standalone signs (with LED lights) can be set:
- Manually in the cockpit with the related toggle switch (on the SIGNS
panel)
- Automatically in relation to the A/C configuration.
The standalone lighted signs are located where the passengers can easily
see them. They give important instructions to the passengers.
- The NS sign is used to tell the passengers not to smoke.
- The FSB sign is used to tell the passengers to fasten their seat belt.
- The RTS sign is used to tell the passengers to return to their seat.
- The lavatory occupied signs are used to show whether the lavatories
are occupied or not. The lavatory door switches control the lavatory
occupied signs which are self dimmable.
- The no PEDs sign (optional) is used to tell the passengers to stop their
personal electronic devices.

33 - Lights
Oct 11, 2013

Page 36
V1813401 - V01T0M0 - VM33D2CABIN3001
STANDALONE SIGNS
33 - Lights
Oct 11, 2013

Page 37

Lavatory Lighting
V1813401 - V01T0M0 - VM33D2CABIN3001
The lavatory lighting illuminates the lavatory compartment through:

- The ceiling LED lights
- The mirror LED lights
- The washtable LED lights.
The lavatory lighting can be controlled from:
- The FAPs and optionally the AAPs
- The door lock mechanism which has three lock positions to set the
related light in the lavatory.

33 - Lights
Oct 11, 2013

Page 38
V1813401 - V01T0M0 - VM33D2CABIN3001
LAVATORY LIGHTING
33 - Lights
Oct 11, 2013

Page 39
V1813401 - V01T0M0 - VM33D2CABIN3001
Architecture and Interfaces

The CIDS directors control and monitor the cabin lighting system through
the Decoder/Encoder Units (DEUs) type A and B.
The cabin crew has access to the lighting functions through the FAPs.
There are also optional AAPs to set lights from specific areas.
To control the lights, the DEUs receive data from:
- The position of the NO SMOKING and SEAT BELTS switches installed
on the SIGNS panel of the Integrated Control Panel (ICP), in the cockpit
- The A/C systems that send messages to the CIDS (A/C on ground,
engines in operation, etc.).
The lighting elements that follow are connected to DEUs A:
- The cabin general lighting
- The cabin application lights
- The spotlights
- The lavatory lights
- The passenger reading lights
- The attendant work lights
- The standalone signs
- The passenger signs (ATA 44).
The vacant or occupied indicator (installed in the cockpit, for the lavatory
from the area of left door 1) and the standalone signs are connected to
the DEU B.

33 - Lights
Oct 11, 2013

Page 40
V1813401 - V01T0M0 - VM33D2CABIN3001
ARCHITECTURE AND INTERFACES

33 - Lights
Oct 11, 2013

Page 41
V1813401 - V01T0M0 - VM33D2CABIN3001
Cabin-Lighting Component Description

The general illumination contains:
- The cabin deck lighting, which includes:
- The cabin general lighting: ceiling lights, sidewall lights, direct ceiling
lights and spotlights.
- The application lights: ceiling recess lights, optional handrail lights and
dome light.
In normal operation, the illumination devices illuminate the cabin at
necessary intensity in all flight phases (during boarding, taxiing and also
for cleaning and maintenance operations).
The FAPs (and optionally the AAPs) control the cabin general
illumination through the CIDS directors and DEUs A.
The Secondary Power Distribution Boxes (SPDBs) supply the cabin
general lighting with 115VAC.
The illumination devices can supply a wide range of light intensity and
colors.
It is possible to change the cabin general lighting through different
scenarios. This can be done from the FAP/Lights page through the
selection of scenarios with the Select key.
The components of the cabin general lighting are the primary light sources
for the lighting scenarios.
Cabin general lighting

The cabin general lighting includes:
- The sidewall lights
- The ceiling lights
- The direct ceiling lights.
The sidewall lights and ceiling lights are made of light devices. Each
light device includes:
- An internal light adapter
- A light module.
33 - Lights
The direct ceiling lights are made of light modules that are connected
a remote light adapter.
Each light module is made of red, green, blue and white LED modules.
The light adapters include the internal power supply of the light device.
It converts 115VAC received from SPDB into 28VDC necessary to
supply the LED module. The light adapters digitally control the
brightness (from 0 to 100%) and color of the LED module through
the order sent by the CIDS through the DEUs A.
All the cabin general light devices can have different sizes in relation
to the cabin layout.
Application lights
The ceiling recess lights and the handrail lights are made of red, green,
blue and white LED modules. They are connected to the remote light
adapters.
The handrail lights on the center OHSCs and the ceiling recess lights
have their own remote light adapters.
The light adapter of the sidewall lights has an external connector
which is used to remotely supply and control the handrail lights
installed on the lateral OHSCs.
The remote light adapters supply power to the light device. It converts
115VAC received from SPDB into 28VDC necessary to supply the
LED module. They digitally control the brightness (from 0 to 100%)
and color of the LED module through the order sent by the CIDS
through DEUs A.
The application light devices can have different sizes in relation to
the cabin layout.
Spotlights
The spotlights are red, green, blue and white LED devices. They are
connected to a remote spotlight adapter. The spotlight adapter digitally
controls the brightness and color (from 0 to 100%) of the spotlights
through the order sent by the CIDS through DEUs A. They also include
Oct 11, 2013

Page 42
V1813401 - V01T0M0 - VM33D2CABIN3001
an internal power supply that converts 115VAC received from SPDB

into 28VDC necessary to supply the LED modules.
In normal operation, the spotlights illuminate special areas at necessary
intensity in all flight phases (during boarding, taxiing and also for
cleaning and maintenance operations).
The number and the position of these spotlights change with the
customer cabin layout.
The FAPs (and optionally the AAPs) control the spotlights through
the CIDS directors and DEUs A. The light intensity of the spotlights
is adjustable from 100% to 0%. The spotlights are part of the lighting
scenarios set for a related compartment (e.g. the entrance area).
Each spotlight adapter has connections with a maximum of six
spotlights. The spotlight adapter is in the location area adjacent to its
related spotlights.
The direct ceiling light and optional dome light contain red, green,
blue and white LED devices and operate with a sufficient number of
remote power supply modules. They are controlled by the CIDS and
supplied by the SPDB 115VAC.

33 - Lights
Oct 11, 2013

Page 43
V1813401 - V01T0M0 - VM33D2CABIN3001
CABIN-LIGHTING COMPONENT DESCRIPTION - CABIN GENERAL LIGHTING ... SPOTLIGHTS

33 - Lights
Oct 11, 2013

Page 44
V1813401 - V01T0M0 - VM33D2CABIN3001
This Page Intentionally Left Blank

33 - Lights
Oct 11, 2013

Page 45

Cabin-Lighting Component Description (continued)
V1813401 - V01T0M0 - VM33D2CABIN3001
Functional logic
A main on and off function is available from a key on the FAP/Lights
page and a key on the FAP hard-key panel. The General Lights/Main
On key is available only on ground (LGERS signal). It is used to set
all the lights of the cabin illumination (main cabin lights, spotlights,
application lights, lavatory lights and reading lights) to the on or off
position, specially for maintenance and servicing purposes.
The intensity of the lights from the cabin general lighting (ceiling
lights, sidewall lights, ceiling recess lights and spotlights) is
automatically dimmed (70%) in these conditions:
- Total loss of the CIDS data bus (buses between the directors and
DEUs A)
- Loss of the CIDS (loss of directors for example).
If a cabin decompression occurs, the general illumination gives full
brightness automatically.
If the engines operate and the cockpit door is unlocked, the intensity
of the spotlight in front of the cockpit door decreases automatically
(at 10%).
These above functional logics operate independently from all light
settings and light scenarios available in the cabin.

33 - Lights
Oct 11, 2013

Page 46
V1813401 - V01T0M0 - VM33D2CABIN3001
CABIN-LIGHTING COMPONENT DESCRIPTION - FUNCTIONAL LOGIC

33 - Lights
Oct 11, 2013

Page 47
V1813401 - V01T0M0 - VM33D2CABIN3001
Lavatory Lighting Architecture and Interface

The lavatory lighting includes:
- The ceiling lights (LEDs)
- The mirror lights (LEDs)
- The washtable lights (LEDs).
The lavatory lighting illuminates the lavatory compartment at a specified
intensity related to the lavatory door status (open, closed or locked).
The door lock-mechanism has three lock positions to set the related lights
in the lavatory to:
- 10% brightness when the lavatory door is open
- 50% brightness when the lavatory door is closed
- 100% brightness when the lavatory door is locked.
To control the lavatory lighting, there is one lavatory light adapter in
each lavatory.
The door lock-mechanism status is directly sent to a lavatory light adapter,
which controls the lavatory lighting to the necessary level.
These lavatory light adapters supply the lavatory lighting with electrical
power.
The CIDS director also receives the door lock-mechanism status from
the lavatory light adapter and through the DEU A. This director controls
the lavatory occupied signs by this data through the DEU B.
The FAP (and optionally the AAPs) can control the lavatory lighting
through the CIDS directors and DEUs A.
The General Lights/Main On key (available on ground) is used to set the
lavatory lighting to the on or off position. It is possible to set the light to
100% for cleaning and maintenance from the LAV MAINT key on the
FAP.
With an optional 100% brightness switch installed in the toilets, it is
possible to illuminate a single lavatory (e.g. for handicapped passengers).

33 - Lights
Oct 11, 2013

Page 48
V1813401 - V01T0M0 - VM33D2CABIN3001
LAVATORY LIGHTING ARCHITECTURE AND INTERFACE

33 - Lights
Oct 11, 2013

Page 49

Reading Lights Architecture and Interface
The reading lights include:
- The passenger reading lights
- The attendant work lights.
V1813401 - V01T0M0 - VM33D2CABIN3001
Passenger reading lights

The passenger LED reading-lights are installed in the PSUs.
The light intensity and the electrical supply of the reading light is
directly controlled by the Passenger Service Adapter (PSA). The PSA
is a component installed in the PSU. There is one PSA for each PSU.
These PSAs have also a direct connection to the DEUs A to control
the reading lights from the FAPs or AAPs (optional).
Each passenger can control its reading light from a P/BSW on the
PSU. From the individually PCU on the seat armrest (IFE system),
another P/BSW controls the passenger reading light individually
through the CIDS directors, DEUs A and PSAs.
The FAPs (and the optional AAPs) can also control the reading lights
through the CIDS directors and DEUs A. The R/L On and R/L Off
keys of the FAPs (and the optional AAPs) can set all the reading lights
to the ON or OFF position. This function is only available when the
A/C is on ground (LGERS signal).
If these functions are configured in the Cabin Assignment Module
(CAM):
- All the reading lights go off when the Main On key of the FAP/Lights
page is in the off position (on ground only).
- The FAPs (in all flight phases) can control each reading light
individually.
- All the reading lights are part of the dimming or a scenario function
of the cabin general lighting.

33 - Lights
Oct 11, 2013

Page 50
V1813401 - V01T0M0 - VM33D2CABIN3001
READING LIGHTS ARCHITECTURE AND INTERFACE - PASSENGER READING LIGHTS

33 - Lights
Oct 11, 2013

Page 51

Reading Lights Architecture and Interface (continued)
Attendant work lights
V1813401 - V01T0M0 - VM33D2CABIN3001
The attendant work lights can illuminate the attendant working areas
and the attendant seats during all flight phases.
The light P/BSW from the area of each attendant work light switches
on and off the related attendant work light.
The attendant work lights receive electrical power through:
- The PSA, when the PSU controls the light (above the attendant seat)
- The standalone PSA, when there is no PSU.
In each configuration, these adapters have a connection to DEUs A
to control the reading lights from FAPs or AAPs. The intensity and
the electrical supply of the reading lights are controlled by the PSA.
If CAM has a special configuration, all the attendant work lights can
be controlled through the LIGHTS MAIN ON/OFF key on the FAP,
only if the A/C is on ground (LGERS signal).

33 - Lights
Oct 11, 2013

Page 52
V1813401 - V01T0M0 - VM33D2CABIN3001
READING LIGHTS ARCHITECTURE AND INTERFACE - ATTENDANT WORK LIGHTS

33 - Lights
Oct 11, 2013

Page 53
EMERGENCY LIGHTING SYSTEM DESCRIPTION (2/3)
V1813401 - V01T0M0 - VM33D3EMERL3001
General
In Emergency (EMER) conditions, the EMER lighting system gives
sufficient lighting to the cabin:
- To identify the emergency exit areas (doors and slides)
- To do a safe and quick evacuation of the A/C.
The emergency lighting system must be satisfactory in darkness and/or
if there is smoke in the cabin, even if no A/C power supply is available.
The Emergency Power-Supply Units (EPSUs) are the heart of the
emergency lighting system.
They have interfaces with the cockpit crew, cabin crew, CIDS and some
A/C systems for control purposes.
The EPSUs are directly connected to the emergency lights system to
supply it with 28VDC when necessary.
If there is a total loss of A/C electrical power, EPSUs supply the
emergency lights from their battery packs for a minimum of ten minutes.
The emergency lights include:
- The cabin-ceiling emergency lights
- The emergency spotlights
- The floor-path marking system
- The emergency-door sill lights
- The exit signs
- The Evacuation (EVAC) area lights.
Note: all the emergency lights use LED technology, but not the
photoluminescent floor-path marking-system, which does not use it.

33 - Lights
Oct 11, 2013

Page 54
V1813401 - V01T0M0 - VM33D3EMERL3001
GENERAL
33 - Lights
Oct 11, 2013

Page 55
V1813401 - V01T0M0 - VM33D3EMERL3001
Emergency-Lighting Control Description

The EMER lighting system can be controlled manually:
- Through the cockpit, by the EMER EXIT LT toggle switch
- Through the cabin, by the EMER key on the FAPs.
In the cockpit, on the SIGNS panel, the EMER EXIT LT toggle switch
has three positions:
- The ON position, which switches on manually the emergency lighting
system.
- The OFF position, which switches off the emergency lighting system.
This is the normal position on ground.
- The ARM position, which arms the emergency lighting system and
switches on automatically in relation to some A/C configurations.
When the ARM position is selected, the emergency lighting system is
started automatically in relation to the configuration of some A/C systems
like:
- The total or partial loss of 28VDC (Normal (NORM) or EMER) and
115VAC NORM.
- The LGERS, which sends a signal related to the landing gear status
(extended or retracted) through the CIDS directors (signal used for
automatic activation of exit signs).
- The NO SMOKING switch on cockpit SIGNS panel, which sends a
signal in relation to its position through the CIDS directors (signal used
for automatic activation of exit signs).
- The Cabin Pressure Control System (CPCS), which sends a signal
related to a cabin rapid decompression through the CIDS directors (signal
used for automatic activation of the exit signs).
The 28VDC NORM (from SPDBs) or 28VDC EMER (from Electrical
Power Distribution Centers (EPDCs)) always supplies the emergency
lighting system with 28VDC through the EPSUs. When the A/C power
supply is not available, each EPSU with its integrated battery pack can
supply 28VDC for a minimum of ten minutes to its connected
emergency-lighting components.
33 - Lights
Note that the EPSU battery pack is charged with 7.2VDC through an
internal converter from 28VDC network.
One more internal converter (7.2VDC to 28VDC) operates when the
EPSU battery pack supplies the emergency lighting network.
Oct 11, 2013

Page 56
V1813401 - V01T0M0 - VM33D3EMERL3001
EMERGENCY-LIGHTING CONTROL DESCRIPTION

33 - Lights
Oct 11, 2013

Page 57
V1813401 - V01T0M0 - VM33D3EMERL3001
Emergency Power-Supply Unit: Functional Logic

The emergency lighting system can be started in all flight phases and its
activation is managed by the EPSU internal logic.
Manual activation
- When the EMER EXIT LT switch is in the ON position, all the
emergency lights come on (this is not applicable to the emergency slide
lights). A manual activation of the system is also possible through the
EMER key on the FAPs.
- When the EMER EXIT LT switch is in the OFF position, all the
emergency lights go off and the OFF indicator light (below the EMER
EXIT LT switch) comes on.
Note that, in this configuration, it is possible to use the FAP/EMER key
to set the emergency lighting system to the on or off position manually.
Automatic activation
When the EMER EXIT LT switch is in the ARM position, the emergency
lighting system is in automatic operation mode.
The EPSUs automatically energize all the emergency lights in, as a
minimum, one of these conditions:
- Loss of 28VDC NORM (from SPDB)
- Loss of 28VDC EMER (from EPDC)
- Loss of 115VAC (from SPDB).
The exit signs also automatically come on when one of these conditions
occurs:
- The NO SMOKING switch is set to the ON position when the landing
gears are in the downlocked position.
- A rapid cabin decompression.

33 - Lights
Oct 11, 2013

Page 58
V1813401 - V01T0M0 - VM33D3EMERL3001
EMERGENCY POWER-SUPPLY UNIT: FUNCTIONAL LOGIC

33 - Lights
Oct 11, 2013

Page 59

Emergency Power-Supply Units
V1813401 - V01T0M0 - VM33D3EMERL3001
The EPSUs supply the emergency lights with the 28VDC (NORM or
EMER) network. The EPSUs includes a battery pack which electrically
supplies the emergency light components.
Note that the EPSUs include a charge module that can charge the EPSU
battery pack with 7.2VDC from the 28VDC aircraft network.
The EPSU battery pack can also supply the emergency lighting network
with 28VDC through an internal converter (7.2VDC to 28VDC).
One EPSU is installed above each passenger door. A total of eight EPSUs
are installed in the cabin.

33 - Lights
Oct 11, 2013

Page 60
V1813401 - V01T0M0 - VM33D3EMERL3001
EMERGENCY POWER-SUPPLY UNITS

33 - Lights
Oct 11, 2013

Page 61

Ceiling Emergency LED-Lights
V1813401 - V01T0M0 - VM33D3EMERL3001
The Ceiling Emergency LED-Light (CELLI) strips supply a minimum

of lighting to the main aisles in longitudinal direction when the emergency
lighting is switched on. In this condition, the EPSUs electrically supply
the CELLIs with 28VDC.
For redundancy, two EPSUs can supply each CELLI strip with 28VDC.
Thus, if there is a failure of one EPSU, the second EPSU supplies each
strip with 28VDC and half of the LEDs illuminates each strip.

33 - Lights
Oct 11, 2013

Page 62
V1813401 - V01T0M0 - VM33D3EMERL3001
CEILING EMERGENCY LED-LIGHTS

33 - Lights
Oct 11, 2013

Page 63

Emergency Spotlights
V1813401 - V01T0M0 - VM33D3EMERL3001
Most of the spotlights used for the general cabin lighting contain a
different emergency light function. The emergency lighting part has
different white LEDs. Then, the emergency spotlight has two different
circuits, one for the general lighting and one for the emergency lighting.
In baseline configuration, the emergency spotlights are installed in cross
aisles, entrances and special areas, where it is not possible to install
CELLIs.
The spotlights emergency-lighting part illuminates these areas
automatically when the emergency lighting system starts.
The EPSUs supply the spotlight emergency-lighting circuits with 28VDC.

33 - Lights
Oct 11, 2013

Page 64
V1813401 - V01T0M0 - VM33D3EMERL3001
EMERGENCY SPOTLIGHTS
33 - Lights
Oct 11, 2013

Page 65

Floor-Path Marking System
V1813401 - V01T0M0 - VM33D3EMERL3001
If there is an emergency cabin evacuation, the floor-path marking system

shows passengers the way to the exits, if it is not possible to see the
overhead lighting (if there is smoke in the cabin for example).
The floor-path marking system has:
- A photoluminescent floor-path marking-system or an electrical floor-path
marking-system. Each system shows the escape path at floor level.
- Exit identifiers that show the location of the exits near the floor level.
The electrical floor-path marking-system includes:
- The seat-mounted emergency lights to illuminate the main aisles (white
or red color)
- The Wall Mounted Emergency Lights (WMELs) and Edge Mounted
Emergency Lights (EMELs) to illuminate areas in front of galleys and
lavatories.
The electrical floor-path marking-system uses LED technology.
The EPSUs can supply the electrical floor-path marking system.
The non-electrical floor-path marking includes floor-path marking-system
strips that are photoluminescent.

33 - Lights
Oct 11, 2013

Page 66
V1813401 - V01T0M0 - VM33D3EMERL3001
FLOOR-PATH MARKING SYSTEM

33 - Lights
Oct 11, 2013

Page 67

Door Sill Lights and External Evacuation-Area Lights
V1813401 - V01T0M0 - VM33D3EMERL3001
The door sill lights are part of the EMELs. They are installed flush
mounted in the door frame near the floor to illuminate the sensitive section
of the door sill area.
The external EVAC-area lights illuminate the area where the deployed
emergency slide hits the ground. The EVAC area lights are installed in
the fuselage in each door.
The door sill lights and external EVAC-area lights use white LED and
are supplied with 28VDC output of the EPSUs.

33 - Lights
Oct 11, 2013

Page 68
V1813401 - V01T0M0 - VM33D3EMERL3001
DOOR SILL LIGHTS AND EXTERNAL EVACUATION-AREA LIGHTS

33 - Lights
Oct 11, 2013

Page 69

Exit Signs
V1813401 - V01T0M0 - VM33D3EMERL3001
There are two types of exit signs:

- The exit location signs on the ceiling to show the position of the exit
areas. They can be seen from each point of the main aisles.
- The exit marking signs above the exits to show the position of the doors.
The exit signs use LED technology.
The EPSUs supply the exit signs with 28VDC when the emergency
lighting system starts.

33 - Lights
Oct 11, 2013

Page 70
V1813401 - V01T0M0 - VM33D3EMERL3001
EXIT SIGNS
33 - Lights
Oct 11, 2013

Page 71
CARGO AND SERVICE COMPARTMENT LIGHTING (2)

Avionics Compartment
V1813401 - V01T0M0 - VM33D4CASVC2301
The avionics compartment illumination is done by LED dome lights.

The LED dome lights are supplied with 115VAC.
Three toggle switches control the LED dome lights:
- One toggle switch is in the cockpit
- Two toggle switches are in the avionics compartment.
Three power outlets are in the avionics compartment:
- One 115VAC power outlet
- Two 28VDC power outlets.

33 - Lights
Oct 11, 2013

Page 72
V1813401 - V01T0M0 - VM33D4CASVC2301
AVIONICS COMPARTMENT
33 - Lights
Oct 11, 2013

Page 73

- In the aft cargo compartment
- In the bulk cargo compartment.
Note: these lights will stay on if they were set to the on position before,
when A/C was on ground.
There is a cargo-compartment light toggle-switch at each service panel
to control the related cargo-compartment lights.
Each service panel has a 115VAC power outlet.
Cargo Lighting Overview

The cargo-compartments lighting system contains:
- The service panels lights
- The loading area lights
- The cargo compartment lights.
All the cargo lights use LED technology.
Note that all the cargo lights are supplied with 28VDC.
Service panel lights

The service panel lights give sufficient illumination to each cargo-door
operation panel (1 FWD and 1 aft) and cargo-loading control panel
(1 FWD and 1 aft).
Each service panel light comes on automatically when the A/C is on
ground with the two engines stopped. The flight phase data is sent by
the FWS to the Secondary Power Distribution Boxes (SPDBs) which
supply the service panels lights with 28VDC.
V1813401 - V01T0M0 - VM33D4CASVC2301
Loading area lights

A loading area light is installed in the entry area of the FWD and aft
cargo-compartments, on the ceiling of each cargo door. These lights
supply sufficient lighting to cargo loading areas.
The SPDBs supply the loading area lights with 28VDC.
The loading area lights are controlled by a loading-area light
toggle-switch on each cargo-door operation panel.
If a cargo door is closed and latched, the Door and Escape Slide
Control System (DSCS) sends a discrete signal to the related SPDB
through the AFDX network. Then, the SPDB automatically sets the
related loading area lights to the off position.
Cargo compartment lights

There are cargo compartment lights in the ceilings of each cargo
compartment:
- In the FWD cargo compartment
33 - Lights
Oct 11, 2013

Page 74
V1813401 - V01T0M0 - VM33D4CASVC2301
CARGO LIGHTING OVERVIEW - SERVICE PANEL LIGHTS ... CARGO COMPARTMENT LIGHTS
33 - Lights
Oct 11, 2013

Page 75
V1813401 - V01T0M0 - VM33D4CASVC2301
CARGO LIGHTING OVERVIEW - SERVICE PANEL LIGHTS ... CARGO COMPARTMENT LIGHTS
33 - Lights
Oct 11, 2013

Page 76
V1813401 - V01T0M0 - VM33D4CASVC2301

33 - Lights
Oct 11, 2013

Page 77

Wheel-Well, Belly Fairing, Air Conditioning Duct and
Accessory Compartment Lighting
Lighting of the nose landing gear bays
Three LED bay lights illuminate the Nose Landing Gear (NLG) bay.
The NLG LED bay lights are supplied with 115VAC by the EPDC.
A toggle switch controls the bay lights.
There are two power outlets in NLG bay:
- One 28VDC power outlet
- One 115VAC power outlet.
Note that the LED lights and the power outlets are supplied in ground
service configuration.
The air conditioning duct and accessory compartment LED-lights can

be set to the on position with the toggle switch only when the A/C is
on ground with the two engines stopped.
The flight phase data is sent by the FWS to the SPDBs that control
the supply of 28VDC to the lights.
The 28VDC power outlet is supplied in ground service configuration.
V1813401 - V01T0M0 - VM33D4CASVC2301
Lighting of the main landing gear bay and belly fairing

Eight LED bay lights illuminate the Main Landing Gear (MLG) bay
and belly fairing. The bay lights are supplied with 115VAC through
the SPDBs. Two toggle switches control the MLG bay and
belly-fairing lights.
Note that the LED lights and the 115VAC power outlets are supplied
in ground service configuration.
These LED lights can be set to the on position with the toggle switch
only when the A/C is on ground with the two engines stopped. The
flight phase data is sent by the FWS to the SPDBs that control the
supply of 115VAC to the lights.
The 28VDC and 115VAC outlets are supplied in ground service
configuration.
Air conditioning duct and accessory compartment lighting

The air conditioning duct and accessory compartment lighting has
two LED lights and one 28VDC power outlet. A toggle switch controls
the lights.
Note that the LED lights and the power outlet are supplied in ground
33 - Lights
Oct 11, 2013

Page 78
V1813401 - V01T0M0 - VM33D4CASVC2301
WHEEL-WELL, BELLY FAIRING, AIR CONDITIONING DUCT AND ACCESSORY COMPARTMENT LIGHTING - LIGHTING OF THE
NOSE LANDING GEAR BAYS ... AIR CONDITIONING DUCT AND ACCESSORY COMPARTMENT LIGHTING
33 - Lights
Oct 11, 2013

Page 79

Service Area Lighting
Waste-tank area lights
V1813401 - V01T0M0 - VM33D4CASVC2301
The waste tank area has two service area LED lights that are controlled
by a toggle switch. This toggle switch is installed near the maintenance
door of the aft wall of the bulk cargo compartment.
The system includes one 28VDC power outlet.
The waste-tank area LED lights can be set to the on position with the
toggle switch only when the A/C is on ground with the two engines
stopped. The flight phase data is sent by the FWS to the SPDBs that
control the supply of 28VDC to the lights.
Note that the LED lights and the 28VDC power outlet are supplied
in ground service configuration.

33 - Lights
Oct 11, 2013

Page 80
V1813401 - V01T0M0 - VM33D4CASVC2301
SERVICE AREA LIGHTING - WASTE-TANK AREA LIGHTS

33 - Lights
Oct 11, 2013

Page 81

Service Area Lighting (continued)
Trimmable horizontal-stabilizer actuator bay lights and
power outlets
V1813401 - V01T0M0 - VM33D4CASVC2301
The Trimmable Horizontal Stabilizer (THS) bay has four LED lights
controlled by a toggle switch.
There are two 28VDC power outlets in the THS bay.
The LED lights of the THS actuator bay can be set to the on position
with the toggle switch only when the A/C is on ground with the two
engines stopped. The flight phase data is sent by the FWS to the
SPDBs that control the supply of 28VDC to the lights.
Note that the LED lights and the power outlet are supplied in ground

33 - Lights
Oct 11, 2013

Page 82
V1813401 - V01T0M0 - VM33D4CASVC2301
SERVICE AREA LIGHTING - TRIMMABLE HORIZONTAL-STABILIZER ACTUATOR BAY LIGHTS AND POWER OUTLETS
33 - Lights
Oct 11, 2013

Page 83

Service Area Lighting (continued)
APU bay lights and power outlets
V1813401 - V01T0M0 - VM33D4CASVC2301
The APU bay has one halogen light. Two toggle switches control this
halogen light.
The APU bay LED-light can be set to the on position only when the
A/C is on ground with the two engines stopped. The flight phase data
is sent by the FWS to the SPDB that controls the supply of 28VDC
to the light through the toggle switches.
A 28VDC power outlet is available.
The LED lights and the 28VDC power outlet are supplied in ground

33 - Lights
Oct 11, 2013

Page 84
V1813401 - V01T0M0 - VM33D4CASVC2301
SERVICE AREA LIGHTING - APU BAY LIGHTS AND POWER OUTLETS

33 - Lights
Oct 11, 2013

Page 85
EXTERIOR LIGHTING SYSTEM DESCRIPTION (2/3)

General Architecture and Operation
The exterior lighting system can be controlled:
- Manually from the EXT LT panel of the Integrated Control Panel (ICP)
- Automatically depending on A/C configurations.
All the control signals (on/off/auto) are transmitted through the AFDX
network to the two CPIOMs. An Exterior Lights Controller (ELCO) is
installed in the CPIOMs. The ELCO software uses the data sent by the
EXT LT control switches and the data which come from the different
A/C systems to compute the lights control orders.
Then, the ELCO sends the control signals, through the AFDX network,
to the Electrical Power Distributions Centers (EPDCs) and Secondary
Power Distribution Boxes (SPDBs) to set the exterior lights to the on or
off position.
When there is a communication failure in the external lighting system

(ICP EXT LT or/and CRDCs or/and AFDX network failure), the
EPDCs, by default, cause to come on the lights that follow:
- Navigation lights
- Landing lights
- Anti-collision lights
- Wing/engine scan lights.
In this configuration, the EPDCs set the remaining lights (i.e.: the taxi
lights, takeoff lights, taxi camera lights, logo lights) to the off position.
V1813401 - V01T0M0 - VM33D5EXTL03001
ELCO software
The ELCO software is used to control and monitor the exterior lighting
system. The ELCO software is hosted in two different CPIOMs. The
two applications operate independently in each CPIOM.
The ELCO software has interfaces through the AFDX network with
the systems that follow:
- The ICP EXT LT control panel (through the CRDCs), to receive the
toggle switch status.
- The Slat and Flap Control Computers (SFCCs), to receive the flap
position for automatic control of the LOGO lights.
- The LGERS, to receive the landing gear status which is used for the
automatic control of some external lights (strobe lights for example).
- The Concentrators and Multiplexers for Video (CMVs), to receive
the selection status of the taxi aid cameras.
- The EPDCs, to control the lights through the Solid State Power
Controllers (SSPCs).
- The SPDBs (through EPDCs), to control the lights through the
SSPCs.
33 - Lights
Oct 11, 2013

Page 86
V1813401 - V01T0M0 - VM33D5EXTL03001
GENERAL ARCHITECTURE AND OPERATION - ELCO SOFTWARE

33 - Lights
Oct 11, 2013

Page 87

Anti-Collision Lights
The anti-collision lighting system generates different flashing light signals
to the external part of the A/C to prevent collisions in flight.
The anti-collision lighting system includes:
- The strobe lights
- The beacon lights.
Two toggle switches independently control the anti-collision lighting
system. The anti-collision lights operate in a synchronized mode when
the STROBE toggle switch is set to the AUTO position and the BEACON
toggle switch is set to the ON position.
For redundancy purpose in the anti-collision lighting system, the EPDC
connections are as follows:
- EPDC 1 supplies the beacon lights
- EPDC 2 supplies the strobe lights.
V1813401 - V01T0M0 - VM33D5EXTL03001
Anti-collision strobe lights

The function of the strobe-lights is to prevent collision.
The anti-collision strobe-light system has:
- Two FWD strobe-light units
- One rear strobe-lights unit.
It includes a total of six white flash tube lights.
Each FWD strobe-light unit, which is installed in each wing tip
leading-edge of the A/C, has:
- Two single flash-tube lights
- A separate Power Supply Unit (PSU).
The rear tail cone strobe-light, which is installed on the tail cone of
the A/C, has:
- Two flash tube lights
- An isolated PSU.
Note that each PSU receives 115VAC from EPDC 2 and supplies an
applicable high voltage to each strobe light.
33 - Lights
The PSU of the lower beacon light monitors the synchronization

between the strobe and the beacon lights.
The three-way STROBE toggle switch on the EXT LT control panel
controls all the flashing strobe lights.
When the STROBE toggle switch is set to:
- ON: all the strobe lights start to flash.
- AUTO: all the strobe lights start to flash, if the A/C is airborne
(confirmed by a L/G not on ground signal from the LGERS).
Otherwise, the strobe lights stay off if the A/C is on ground.
- OFF: the strobe lights stay off.
Note: If the STROBE toggle switch is set to the OFF position with
A/C in-flight (confirmed by a L/G not on ground signal), the STROBE
LT OFF memo is shown on the ECAM.
Operation
The position of the STROBE toggle switch is first sent to the CPIOMs
which host the ELCO software. Then the ELCO software processes
the toggle-switch status data and control the strobe lights (on or off)
through EPDC 2. EPDC 2 supplies 115VAC power to the PSUs of
the strobe lights.
Oct 11, 2013

Page 88
V1813401 - V01T0M0 - VM33D5EXTL03001
ANTI-COLLISION LIGHTS - ANTI-COLLISION STROBE LIGHTS

33 - Lights
Oct 11, 2013

Page 89

Anti-Collision Lights (continued)
Anti-collision beacon lights
V1813401 - V01T0M0 - VM33D5EXTL03001
The function of the beacon lights is to prevent collision.

The beacon light system has three red flashing beacon lights:
- Two beacon lights are installed on the top of the fuselage
- One beacon light is installed on the bottom of the fuselage.
Note that the beacon lights use LED technology.
Each beacon light is supplied by a different PSU. Each PSU receives
115VAC from EPDC 1.
The BEACON toggle switch on the EXT LT control panel controls
the three beacon lights with ON and OFF positions.
Operation
The position of the BEACON toggle switch is first sent to the CPIOMs
which host the ELCO software. Then the ELCO software processes
the toggle-switch status data and controls the beacon lights (on or off)
through EPDC 1. EPDC 1 supplies the PSUs of the beacon lights with
115VAC.
Note that the PSU of the lower beacon light controls the
synchronization between the strobe and beacon lights through a
specific analog wire.

33 - Lights
Oct 11, 2013

Page 90
V1813401 - V01T0M0 - VM33D5EXTL03001
ANTI-COLLISION LIGHTS - ANTI-COLLISION BEACON LIGHTS

33 - Lights
Oct 11, 2013

Page 91
V1813401 - V01T0M0 - VM33D5EXTL03001
Navigation Lights
The NAV lights system gives an external and visual indication of the
A/C position and its flight direction.
The navigation lights contain:
- One navigation LED-light, which is installed at the leading edge of each
wing tip. The right LED-light is green. The left LED-light is red.
- One white navigation LED-light, which is installed on the tail cone
below the APU outlet.
Each wing-tip navigation-light has one integrated PSU and the rear
tail-cone light has a separated PSU.
For redundancy purpose, the wing-tip left (red color) and the right (green
color) navigation lights and the rear navigation light include two LED
arrays.
Each LED array is electrically supplied independently from one of the
EPDC:
- EPDC 1 for the NAV1 supply
- EPDC 2 for the NAV2 supply.
Note that the three PSUs of these lights include two different
power-supply connectors:
- The NAV1 connector receives 115VAC from EPDC 1
- The NAV2 connector receives 115VAC from EPDC 2.
Then, the PSU supplies the necessary VDC voltage to the selected LED
array from EPDC 1 or EPDC 2.
The NAV toggle switch on the EXT LT control panel controls the
navigation lights with the 1 (for NAV1), 2 (for NAV2) and OFF positions.
The NAV lights are on when the NAV toggle switch are set to the 1 or
2 position.
Note that the NAV1 system is the primary selection and the NAV2 system
is selected when the NAV1 is not available.
The NAV lights can also be energized from steering disconnect-panel
circuit on the Nose Landing Gear (NLG) through the tow truck
power-connector.
33 - Lights
Operation
The position of the NAV toggle switch is first sent to the CPIOMs which
host the ELCO software. Then the ELCO software processes the
toggle-switch status data and controls the navigation lights (NAV1 on,
or NAV2 on, or off) through EPDC 1 or EPDC 2.
Oct 11, 2013

Page 92
V1813401 - V01T0M0 - VM33D5EXTL03001
NAVIGATION LIGHTS
33 - Lights
Oct 11, 2013

Page 93
V1813401 - V01T0M0 - VM33D5EXTL03001
Logo Lights
The logo lights are used to illuminate the airline logo on the vertical
stabilizer.
One logo light unit (composed of one High Intensity Discharge (HID)
light) is installed on each side of the Trimmable Horizontal Stabilizer
(THS).
Each light is connected to a different PSU, which is supplied with
115VAC from the SPDBs.
Note that the SPDBs are directly controlled by the EPDCs.
The three-way LOGO toggle switch on the EXT LT control panel controls
the logo lights.
When the LOGO toggle switch is set to:
- ON: the logo lights come on.
- AUTO: the logo lights come on automatically when the slats are lowered
to 18 degrees minimum (lever in position 1 minimum i.e. slats not in) or
NLG is on ground. Then, the logo lights come on automatically during
taxiing, takeoff, climb, approach, landing and on ground phases.
- OFF: the logo lights stay off.
Operation
The position of the LOGO toggle switch is first sent to the CPIOMs
which host the ELCO software. The ELCO software processes the
toggle-switch status data in relation to other A/C data (slat position from
SFCC and L/G status from LGERS). Then, the ELCO software controls
the logo lights through EPDC 1 or EPDC 2 and SPDBs.

33 - Lights
Oct 11, 2013

Page 94
V1813401 - V01T0M0 - VM33D5EXTL03001
LOGO LIGHTS
33 - Lights
Oct 11, 2013

Page 95
V1813401 - V01T0M0 - VM33D5EXTL03001
Wing and Engine Scan Lights

The wing and engine scan lights are used by the flight crew members to
monitor formation of ice on the wing leading edge and on the engine
intake.
There are two wing and engine scan lights.
On the FWD fuselage, the system has:
- One left wing and engine scan light (bi-function)
- One right wing and engine scan light (bi-function).
These lights use the HID technology.
The two wing and engine scan lights are connected to a different PSU.
These PSUs are supplied with 115VAC from EPDC 1 or EPDC 2.
The WING toggle switch on the EXT LT control panel controls the wing
and engine scan lights with ON and OFF positions.
The wing and engine scan lights are on when the WING toggle switch
is set to the ON position and they are off if this switch is set to the OFF
position.
Operation
The position of the WING toggle switch is first sent (through the CRDCs
and AFDX network) to the CPIOMs which host the ELCO software. The
ELCO software processes the toggle-switch status data. Then, the ELCO
software controls the wing and engine scan lights (on or off) through
EPDC 1 or EPDC 2 that supplies 115VAC to the PSUs.

33 - Lights
Oct 11, 2013

Page 96
V1813401 - V01T0M0 - VM33D5EXTL03001
WING AND ENGINE SCAN LIGHTS

33 - Lights
Oct 11, 2013

Page 97
V1813401 - V01T0M0 - VM33D5EXTL03001
Runway Turnoff and Taxiing Lights

The runway turnoff and taxiing lights give sufficient illumination on
ground during the taxiing phase (in conjunction with the RH takeoff
lights). The runway turnoff and taxiing lights are also used with the
landing lights and takeoff lights during takeoff and landing phases.
The runway turnoff and taxiing lights are installed in a same assembly
that includes:
- Three optical modules (one for the taxi light and two for the runway
turnoff lights) with three HID lamps (one for each optical module)
- A common integrated PSU.
A three-way NOSE toggle switch on the EXT LT panel controls the
runway turnoff and taxiing lights.
When the NOSE toggle switch is set to:
- OFF: the runway turnoff and taxiing lights are off
- TAXI: the runway turnoff and taxiing lights are on
- T.O: the runway turnoff and taxiing lights and takeoff lights are on.
Note that the lights can be switched on only when the NLG is downlocked.
The runway turnoff and taxiing lights automatically go off as soon as the
A/C is in-flight with NLG uplocked, if the NOSE toggle switch is set to
the TAXI or T.O position.
Operation
The position of the NOSE toggle switch is first sent to the CPIOMs wich
host the ELCO software. The ELCO software processes the toggle-switch
status data in relation to other A/C data (NLG status from the LGERS).
Then, the ELCO software controls the runway turnoff and taxiing lights
(on or off) through EPDC 1 that supplies 115VAC to the common
integrated PSU.

33 - Lights
Oct 11, 2013

Page 98
V1813401 - V01T0M0 - VM33D5EXTL03001
RUNWAY TURNOFF AND TAXIING LIGHTS

33 - Lights
Oct 11, 2013

Page 99
V1813401 - V01T0M0 - VM33D5EXTL03001
Takeoff Lights
The takeoff lights illuminate the ground to clearly identify the runway
during takeoff and ground roll at night.
The A/C is installed with two takeoff light assemblies on the NLG leg.
Each takeoff light assembly includes:
- Three optical modules with three HID lamps (one for each optical
module)
The three-way NOSE toggle switch on the EXT LT control panel controls
the taxi and takeoff lights:
- OFF: the runway turnoff and taxiing lights and takeoff lights are off.
- TAXI: the runway turnoff and taxiing lights are on.
- T.O: the runway turnoff and taxiing lights and takeoff lights are on.
Note that the takeoff lights can operate only when the NLG is
downlocked. The takeoff lights automatically go off as soon as the A/C
is in flight with NLG uplocked, if the NOSE toggle switch is on TAXI
or T.O position.
Operation
The position of the takeoff lights toggle switch is first sent to the CPIOMs
hosting the ELCO software. The ELCO software processes the switch
position data in relation to other A/C data (NLG status from the LGERS).
Then, the ELCO software controls the takeoff lights (on or off) through
EPDC 2 that supplies 115VAC to the related PSUs.

33 - Lights
Oct 11, 2013

Page 100
V1813401 - V01T0M0 - VM33D5EXTL03001
TAKEOFF LIGHTS
33 - Lights
Oct 11, 2013

Page 101
V1813401 - V01T0M0 - VM33D5EXTL03001
Taxiing-Aid Camera Lights

The Taxiing Aid Camera (TAC) light system supplies sufficient light to
let the flight crew members see (on the cockpit displays) the position of
the NLG and Main Landing Gears (MLGs) in relation to the taxiway
during taxiing phases when the two TACs are set to the on position.
The taxiing-aid camera light system includes four lamps of HID type:
- Two FWD TAC lights at the bottom side of the nose fuselage (LH and
RH side)
- Two aft TAC lights at the bottom side of the wings (LH and RH wings)
- Four different PSUs (each light is connected to a different PSU).
The three-way NOSE toggle switch on the EXT LT control panel controls
the TAC lights through three positions: OFF, TAXI and T.O.
The TAC lights operate if:
- The NOSE toggle switch is in the T.O or TAXI position.
- The taxiing-aid camera light system is activated in the cockpit through
the TAXI P/BSW on the EFIS control panel or through the VIDEO
P/BSW on the ECAM control panel.
- The L/G is on ground.
Operation
The position of the NOSE toggle switch is first sent to the CPIOMs which
status data in relation to other A/C data (L/G status from the LGERS and
the TACS ON signal from the CMVs). Then, the ELCO software controls
the TAC lights (on or off) through EPDC 1 (for LH lights) and EPDC 2
(for RH lights) that supply 115VAC to the related PSUs.

33 - Lights
Oct 11, 2013

Page 102
V1813401 - V01T0M0 - VM33D5EXTL03001
TAXIING-AID CAMERA LIGHTS

33 - Lights
Oct 11, 2013

Page 103

Landing Lights
V1813401 - V01T0M0 - VM33D5EXTL03001
The landing lights give a forward lighting of the landing area when the
A/C is in approach at night and/or in bad weather conditions.
The landing lights system has two landing light assemblies installed in
each wing root on the inboard leading edge.
Each landing light assembly contains:
- Three optical heads with three HID lamps (one for each optical head)
The LDG toggle switch on the EXT LT control panel controls the landing
lights with ON and OFF positions.
Operation
The position of the LDG toggle switch is first sent to the CPIOMs which
status data. Then, the ELCO software controls the landing lights (on or
off) through EPDC 1 (for LH lights) and EPDC 2 (for RH lights) that
supply 115VAC to the related PSUs.

33 - Lights
Oct 11, 2013

Page 104
V1813401 - V01T0M0 - VM33D5EXTL03001
LANDING LIGHTS
33 - Lights
Oct 11, 2013

Page 105
LIGHTING SYSTEM MAINTENANCE (2/3)

Emergency Lighting Tests from OMS Interface
V1813401 - V01T0M0 - VM33M1MAINT3001
The interactive emergency-lighting tests are done from the CMS and
through the CIDS. These tests are launched from the OMS HMIs
(Human-Machine Interfaces) (i.e.: OMT, Portable Multipurpose Access
Terminal (PMAT) or CDS) trough the System/Report Test menu of ATA
33:
- The system test checks the condition of the electronic circuits and battery
pack voltage of all the Emergency Power Supply Units (EPSUs) with
their connected electrical loads.
- The battery capacity test monitors that the capacity of each EPSU battery
is sufficient to supply its loads for a minimum of 10 minutes. Around 75
minutes are necessary for the battery capacity check to be completed.
The CMS, which is hosted in the OIS, is connected to the EPSUs through
the SCIs, the CIDS directors and the Decoder/Encoder Units B (DEUs
B) to get the System/Report Test functions for the emergency lighting
system.

33 - Lights
Oct 11, 2013

Page 106
V1813401 - V01T0M0 - VM33M1MAINT3001
EMERGENCY LIGHTING TESTS FROM OMS INTERFACE

33 - Lights
Oct 11, 2013

Page 107
V1813401 - V01T0M0 - VM33M1MAINT3001
EPSU Individual Local Test

The EPSU individual test and the TEACH IN procedure can be launched
with an EPSU front-face pushbutton.
The EPSU individual test (pushbutton pushed < 5 sec).
An individual test of each EPSU with its battery pack and its connected
emergency lights can be done with a test pushbutton located on the front
face of each EPSU. The test results are shown directly on the EPSUs
thanks to the LEDs status.
There are some LEDs on the EPSUs to show the failure or the good
condition of:
- The EPSU UNIT
- The BATTERY pack
- The connected EXTERIOR emergency light (evacuation area lights)
- The connected INTERIOR lights and EXIT SIGNS.
The TEACH IN procedure (pushbutton pushed > 5 sec.)
A load programming procedure is automatically done when a new EPSU
battery or when a new EPSU is installed. Whis this procedure, called
TEACH IN procedure, you can measure and keep the load value of the
related EPSU in the EPSU memory. This load value corresponds to the
current value given by the EPSU during the procedure to supply all the
connected emergency lights and signs.
This load value is used as reference value during an OMS system test or
during an EPSU individual test to find the failure of a light or an overload
condition (because of a short circuit). The TEACH IN procedure can be
manually started (e.g. after a light replacement) through a pushbutton
located on the front face of the EPSU.
Note that it is necessary to make sure that all the emergency lights
connected to the related EPSU operate correctly before the launch of the
TEACH IN procedure.

33 - Lights
Oct 11, 2013

Page 108
V1813401 - V01T0M0 - VM33M1MAINT3001
EPSU INDIVIDUAL LOCAL TEST

33 - Lights
Oct 11, 2013

Page 109
V1813401 - V01T0M0 - VM33M1MAINT3001
Exterior Lighting Maintenance

The software of the Exterior Lights Controller (ELCO) is connected to
the FWS (for memo, warnings and dispatch advisory generation) and to
the ACMS (to support the Trouble Shooting Manual (TSM) and Aircraft
Maintenance Manual (AMM) activities on the A/C) to improve the
monitoring, the maintenance and the troubleshooting of the exterior
lighting system.
The ELCO software also has a BITE function (Electrical System BITE
Function (ESBF)) that can give the report of the failure of one Line
Replaceable Unit (LRU) to the CMS. In this case, the ESBF generates a
special failure message.
Moreover, there are some of the Power Supply Units (PSUs) of the
exterior lights installed with a LED that gives an indication about their
power supply status, to improve the failure diagnosis.
If there is an exterior light failure and the LED is on, the power supply
operates correctly and so the lamp must be defective. But, if there is an
exterior light failure and the LED is off, the failure must be related to the
PSU.
The PSUs of the following exterior lights are installed with this LED:
- Taxi camera lights
- Wing and engine scan lights
- Logo lights.

33 - Lights
Oct 11, 2013

Page 110
V1813401 - V01T0M0 - VM33M1MAINT3001
EXTERIOR LIGHTING MAINTENANCE

33 - Lights
Oct 11, 2013

Page 111
V1813401 - V01T0M0 - VM33M1MAINT3001
ACMS Exterior Lighting Maintenance

The ACMS exterior-lights system pages can be used to support the
exterior lights AMM/TSM activities on the A/C.
These ACMS functions can give real-time system pages for all the exterior
lights:
1 NAVIGATION data from navigation lights
2 ANTI COLLISION data from beacon and strobe lights
3 NOSE data from takeoff and taxi and runway turnoff lights
4 LANDING data from landing lights
5 WING and ENGINE data from wing and engine lights
6 LOGO data from logo lights
7 TAXI CAMERA data from taxi camera lights.
For each light component, there are the following data:
- Functional Item Number (FIN)
- Elapsed time
- Remaining time (estimated)
- Life Reached time (estimated)
- Real time Consumption.
The Remaining time is a theoretical value that is given by the light
supplier. The maximum value of the Remaining time is equivalent to the
value of the Mean Time Between Failures (MTBF) of the light component.
This value is given in hours. When there is no more remaining time
(Remaining time counter is zero), a light replacement can be planned,
but it stays the decision of the pilot to report if the light performance is
satisfactory or not.
The Life Reached time is linked to the light luminosity performance. The
supplier gives a theoretical value in hours under which the performance
of the light is supposed to fall below the light luminosity performance
requirement.
When the threshold is reached, an amber YES is shown on the ACMS
area of the light. The light replacement can be planned.
33 - Lights
If the threshold of the Life Reached time is not reached, a green NO is

shown on the ACMS area of the light.
In addition, for the navigation, strobe and beacon lights, when the
threshold of the Life Reached time is reached, a special dispatch message
is triggered and the light must be replaced.
For the other exterior lights, the status of the Life Reached time (YES or
NO) is given, but no dispatch message is triggered.
Oct 11, 2013

Page 112
V1813401 - V01T0M0 - VM33M1MAINT3001
ACMS EXTERIOR LIGHTING MAINTENANCE

33 - Lights
Oct 11, 2013

Page 113

CMS Exterior Lighting Maintenance
V1813401 - V01T0M0 - VM33M1MAINT3001
The exterior light system has a special CMS menu.

This menu is accessible from the EPDS and EXT LT menu through the
System/Report Test menu of ATA 33. It gives access to the EXT LT test
functions and EXT LT specific functions.
After the removal/installation of a light component, the Operational time
menu gives the approval for the resetting to zero of the elapsed time
counter and for the reinitialization of the remaining time and the end of
life of the counters.
It is also possible to change the component Lifetime value and the
Threshold value in relation to the light supplier recommendations.

33 - Lights
Oct 11, 2013

Page 114
V1813401 - V01T0M0 - VM33M1MAINT3001
CMS EXTERIOR LIGHTING MAINTENANCE

33 - Lights
Oct 11, 2013

Page 115
LIGHTING SYSTEM CONTROL AND INDICATING (2/3)
V1813401 - V01T0M0 - VM33I1000003001
Cabin Lighting (2/3)

This Control / Indicating module provides a general presentation of the
Cabin Lighting control through the MP-FAP.
On the MP-FAP Hard Key panel:
MAIN ON/OFF P/B: for Maintenance purpose and on ground only, this
push-button allows to switch ON at 100 % all the Cabin lights (general
& Entries & Galley & lavatories Lightings) and all the Reading Lights
& Attendant Work Lights.
LAV MAINT P/B: for Cleaning and Maintenance purposes and on ground
only, this push-button allows to switch ON at 100 % all the Cabin lavatory
lightings.
On the MP-FAP touch screen:
CABIN STATUS page: this page provides an overall status of the Cabin.
This page allows direct access to the 5 system pages: LIGHTS,
TEMPERATURE, DOORS/SLIDES, WATER/WASTE, SMOKE
DETECTION.
LIGHTS page: this page mainly allows to control the general illumination
in the different areas of the cabin.
It is possible either to adjust manually the lighting (fine tuning control)
or to call a predefined scenario (Cruise, Dinner....) for the following areas:
- Zones (First Class, Business class, Economy class, Tourist class),
- Rooms (FWD Galley, AFT Galley, FCRC, CCRC...),
- Entries (Door 1, Door 2, Door 3, Door 4),
The "Aircraft-wide Adjustment" area (in the Lights page) gives access
to the following functions:
- General Lights function. This mode allows the selection of Night Mode,
MAIN ON/OFF function (available on ground only), and Reading
Lights general control (Available on ground only).
- Entire Scenario. This mode allows to call a predefined scenario, which
will apply to the whole cabin.
- Light Strips function to switch on independently the Windows light
strips, the Center light strips, or the Aisle light strips.
33 - Lights
LIGHTS PRESET page: this page allows to call and load a predefined
scenario, which may apply for the whole flight and within the whole
cabin.
CABIN LIGHT PROGRAMMING page allows to program and save
within the CIDS a lighting scenario. These lighting scenarios can also be
loaded via the CAM (Cabin Assignment Module) within the CIDS
memory.
These programmed scenarios, which apply for a whole flight and within
the whole cabin, can be called via the LIGHTS PRESET page.
The Reading Lights page (accessible via the SEAT SETTING page)
allows to Switch ON / OFF individually all passenger Reading Lights in
all flight phases (if programmed within the CAM).
Emergency Lighting (2)

This Control / Indicating module provides a general presentation of the
Emergency Lighting.
The Emergency Lighting system can be activated and controlled by the
flight crew from the "ON - ARM - OFF" EMER LT switch located in
the cockpit on the SIGNS panel.
When the switch is selected to the "ON" position, all emergency lights
in the aircraft will turn ON.
When the switch is selected to the "OFF" position, the emergency lighting
system is disabled. This condition is confirmed by an amber "OFF"
indication below the EMER LT switch.
With the switch in "ARM" position, the emergency lighting system will
be activated automatically. For example in case of loss of 115 VAC
NORMAL and/or 28 V DC Non-Essential, all Emergency lights are
switched on automatically.
The Emergency Lighting system can be activated and controlled by the
cabin crew from the EMER push-button on the MP-FAP.
By selecting ON this EMER P/B, all emergency lights in the aircraft will
turn ON.
Oct 11, 2013

Page 116
V1813401 - V01T0M0 - VM33I1000003001
CABIN LIGHTING (2/3) & EMERGENCY LIGHTING (2)

33 - Lights
Oct 11, 2013

Page 117
V1813401 - V01T0M0 - VM33I1000003001

33 - Lights
Oct 11, 2013

Page 118
V1813401 - V01T0M0 - VM33I1000003001

33 - Lights
Oct 11, 2013

Page 119
V1813401 - V01T0M0 - VM33I1000003001

33 - Lights
Oct 11, 2013

Page 120
V1813401 - V01T0M0 - VM33I1000003001

33 - Lights
Oct 11, 2013

Page 121
V1813401 - V01T0M0 - VM33I1000003001

33 - Lights
Oct 11, 2013

Page 122
V1813401 - V01T0M0 - VM33I1000003001

33 - Lights
Oct 11, 2013

Page 123
V1813401 - V01T0M0 - VM33I1000003001

33 - Lights
Oct 11, 2013

Page 124
V1813401 - V01T0M0 - VM33I1000003001

33 - Lights
Oct 11, 2013

Page 125
V1813401 - V01T0M0 - VM33I1000003001

33 - Lights
Oct 11, 2013

Page 126
V1813401 - V01T0M0 - VM33I1000003001

33 - Lights
Oct 11, 2013

Page 127
AIRBUS S.A.S.
31707 BLAGNAC cedex, FRANCE
STM
REFERENCE V1813401
OCTOBER 2013
PRINTED IN FRANCE
AIRBUS S.A.S. 2013
ALL RIGHTS RESERVED
AN EADS COMPANY

33 Lights PDF

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

33 Lights PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

33 Lights PDF

Uploaded by

Copyright:

Available Formats

A350

TECHNICAL TRAINING MANUAL

This document must be used for training purposes only

Under no circumstances should this document be used as a reference

It will not be updated.

All rights reserved

AIRBUS Environmental Recommendation

A350 TECHNICAL TRAINING MANUAL

Cockpit Lighting System Description (2) . . . . . . . . . . . . . . . . . . . . . . 2

MAINTENANCE COURSE - T1+T2 - RR Trent XWB

Oct 21, 2013

A350 TECHNICAL TRAINING MANUAL

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

V1813401 - V01T0M0 - VM33D1COCKT2301

MAINTENANCE COURSE - T1+T2 - RR Trent XWB

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

Oct 11, 2013

V1813401 - V01T0M0 - VM33D1COCKT2301

A350 TECHNICAL TRAINING MANUAL

COCKPIT GENERAL ILLUMINATION

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

Oct 11, 2013

A350 TECHNICAL TRAINING MANUAL

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

V1813401 - V01T0M0 - VM33D1COCKT2301

MAINTENANCE COURSE - T1+T2 - RR Trent XWB

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

Oct 11, 2013

V1813401 - V01T0M0 - VM33D1COCKT2301

A350 TECHNICAL TRAINING MANUAL

AMBIENT LIGHTING - GENERAL AMBIENT LIGHTING

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

Oct 11, 2013

A350 TECHNICAL TRAINING MANUAL

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

V1813401 - V01T0M0 - VM33D1COCKT2301

The DOME LT rotary knob has a STORM position. This position is

MAINTENANCE COURSE - T1+T2 - RR Trent XWB

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

Oct 11, 2013

V1813401 - V01T0M0 - VM33D1COCKT2301

A350 TECHNICAL TRAINING MANUAL

AMBIENT LIGHTING - STORM FUNCTION

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

Oct 11, 2013

A350 TECHNICAL TRAINING MANUAL

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

V1813401 - V01T0M0 - VM33D1COCKT2301

The CAPT and F/O individual working-area lighting includes:

MAINTENANCE COURSE - T1+T2 - RR Trent XWB

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

Oct 11, 2013

V1813401 - V01T0M0 - VM33D1COCKT2301

A350 TECHNICAL TRAINING MANUAL

AMBIENT LIGHTING - PILOT INDIVIDUAL WORKING-AREA LIGHTING

COCKPIT LIGHTING SYSTEM DESCRIPTION (2)

Oct 11, 2013

A350 TECHNICAL TRAINING MANUAL