Daewoo 14Q1

Service Manual
38 / 48 / 51 Cm Mono Colour Television
CHASSIS : CP-370
MODEL : 14Q1/20Q1/21Q1
14Q2/20Q2/21Q2
14Q3/20Q3/21Q4
14T1/20T1/21T1
14T2/20T2/21T2
14T3/20T3
@@
,,
DAEWOO ELECTRONICS CO., LTD.
Downloaded from www.Manualslib.com manuals search engine
CONTENTS
Specifications ................................................................................................................ 1
Safety Instruction ......................................................................................................... 2
Circuit block Diagram ................................................................................................. 3
Alignment Instructions ............................................................................................... 4
IC Description ................................................................................................................ 7
Circuit Description ....................................................................................................... 31
PCB Layouts
PRINTED CIRCUIT BOARDS .................................................................................... 38
SCHEMATIC DIAGRAM ............................................................................................. 39
Trouble Shooting Charis ............................................................................................. 40

Important IC Voltage Charts .............................................................................................. 47
Electrical Part List............................................................................................................... 49
Q Model T Model Difference Part List ............................................................................... 64
Inch difference Part List ..................................................................................................... 65
Mechanical Exploded View and Part List ......................................................................... 66
Specifications
Q : 1SPEAKER MODEL, T : 2SPEAKER MODEL
VM : WITHOUT TXT. MODEL, TM : WITH TXT. MODEL
TV Standard
PAL/SECAM-B/G, D/K, I, H, NTSC-3.58/4.43
Mains Voltage
100~250V AC, 50/60Hz
Power Consumption
14Q = 69W, 14T = 74W

20Q = 79W, 20T = 84W
21Q = 79W, 21T = 84W
Sound output
. 1 Speaker : 3W( at 80% MOD. 10% THD)

. 2 Speaker : 4W + 4W( at 80% MOD. 10% THD)
Speaker
. 1 Speaker : 3W, 16 ohm

. 2 Speaker : 7.5W, 8 ohm(2EA)
Antenna
75 ohm unbalanced
Impedance
300 ohm balanced with supplied balun
Tuning system
Voltage Synthesize Tuning System
Memory channel
VM : 100 channels, TM : 70 channels
Reception
VHF - L : CH2 - CH4
channel Unit
VHF - H : CH5 - CH12

Cable Band : CHS1 - CHS3, CHS1 - CHS20
Hyper Band : CHS21 - CHS40(option)
UHF : CH21 - CH69
Remote control
VM : R-28B04, TM : R-28B03
Screen size
14 : 34cm (A34JLL 90 02)

20 : 48cm (A48JLL 90 02)
21 : 51cm (A51JLL 90 02)
Weight
14 : 9.5Kg(set)
20 : 16.5Kg(set)
21 : 20.5Kg(set)
Indication
On-Screen Display
- MENU
Picture(Bright, Color, Contrast, Sharpness, TINT)
TIMER(CLOCK, WAKE-UP-TIME, ACTIVATE, WAKE-UP-PROG)
LANGUAGE
PRESET
EDIT
SLEEP TIMER
AV
SOUND MUTE
VOLUME CONTROL
1
Safety Instruction
WARNING: Before servicing this chassis, read the X-RAY RADIATION precaution, safety
precaution and product safety notice below.
X-RAY RADIATION PRECAUTION

1. Excessive high voltage can produce potentially
hazardous X-RAY RADIATION.To avoid such
hazards, the high voltage must not exceed the
specified limit. The nominal value of the high
voltage of this receiver is 22-23kv(14), 2526kv(20, 21) at max beam current. The high
voltage must not, under any circumstances,
exceed 27.5kv (14", 20), 29.0kv(21).
Each time a receiver requires servicing, the high
voltage should be checked. It is recommended

the reading of the high voltage recorded as a part
of the service records. it is important to use an
accurate and reliable high voltage meter.
2. The only source of X-RAY Radiation in this TV
receiver is the picture tube. For continuous
RADIATION protection, the replacement tube
must be exactly the same type tube as specified
in the parts list.
SAFETY PRECAUTION
1. Potentials of high voltage are present when this
receiver is operating. Operation of the receiver
outside the cabinet or with the back cover
removed involves a shock hazard from the
receiver.
1) Servicing should not be attempted by anyone
who is not thoroughly familiar with the
precautions necessary when working on highvoltage equipment.
2) Always discharge the picture tube to avoid the
shock hazard before removing the anode cap.
3) Discharge the high potential of the picture tube
before handling the tube. The picture tube is
highly evacuated and if broken, glass
fragments will be violently expelled.
2. If any Fuse in this TV receiver is blown, replace it

with the FUSE specified in the Replacement
Parts List.
3. When replacing a high wattage resistor(oxide
metal film resistor) in circuit board, keep the
resistor 10mm away from circuit board.
4. Keep wires away from high voltage or high
temperature components.
5. This receiver must operate under AC260 volts,
50Hz/60Hz. (AC 100~250 volts, 50/60Hz)NEVER
connect to DC supply or any other power or
frequency.
PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in this chassis
have special safety-related characteristics.
These characteristics are often passed unnoticed
by a visual inspection and the X-RAY RADIATION
protection afforded by them cannot necessarily be
obtained by using replacement components rated
for higher voltage, wattage, etc. Replacement parts
which have these special safety characteristics are
identified in this manual and its supplements,
electrical components having such features are
identified by designated symbol on the parts list.

Before replacing any of these components, read the
parts list in this manual carefully. The use of
substitute replacement parts which do not have the
same safety characteristics as specified in the parts
list may created X-RAY Radiation.
2
Alignment Instructions
1. AFT
1.1 Standard B/G,D/K,I
1) Set a Signal Generator with
- RF FREQUENCY = 38.9 MHz,
- RF OUTPUT LEVEL = 80 5 dBuV
- System = PAL / SECAM - B/G, D/K, I
NTSC - 3.58/4.43
2) Connect the Signal Generator RF Output to P101 (Tuner IF Output).
There must be no signal input to the tuner.
3) Press the AFT KEY and wait until the TV screen display AFT OK.
2. AGC
1) Set a Pattern Generator with RF LEVEL 63 2 dBuV .
2) Connect a OSCILLOSCOPE PROBE to P102 (TUNER AGC INPUT).
3) Adjust AGC UP/DOWN KEY the voltage drop 3.5V dc point its maximum voltage.(TDA8374A N1 VERSION)
Adjust AGC UP/DOWN KEY the voltage drop 1.5V dc over blow its maximum voltage(TDA8374A N3 VERSION)
Alternative Method
1) Set a Pattern Generator with
- RF LEVEL 80 5 dBuV
- PAL CROSSHATCH
( without SOUND CARRIER )
2) Connect a OSCILLOSCOPE
( Bandwidth
100MHz ) PROBE
to P101 (TUNER IF OUTPUT).
3) Use AGC UP/DOWN KEY to obtain
an envelop amplitude 200 + 20 mVp-p.
3. SCREEN
1) Apply a COLOR BAR pattern signal.
2) Set the CONTRAST, BRIGHTNESS
to MAX, COLOR to MIN.
3) Set the R,G,B LEVEL to CENTER (31/63)
with R,G,B UP/DOWN KEY.
4) Connect a OSCILLOSCOPE PROBE
to P904 ( CRT CATHOD R, G, B ).
5) Adjust the SCREEN VOLUME on FBT
such that the highest black level voltage
160 5Vdc (20, 21), 130 5Vdc (14).
Black level
160 5Vdc ( 20, 21 )
130 5Vdc ( 14 )
GND
4. WHITE BALANCE
1) Set the TV to NOR I mode.
2) Set the R,G,B LEVEL to CENTER with R,G,B UP/DOWN KEY .
3) Adjust the R,G,B UP/DOWN KEY of the other color which did not appear
on the screen to obtain WHITE.
5. FOCUS
1) Apply a RETMA PATTERN signal.
2) Adjust the FOCUS VOLUME on FBT to obtain optimal resolution.
4
6. GEOMETRY
6.1 VERTICAL CENTER
2) Pressing the V-SIZE UP/DOWN KEY, the
lower half of the screen is blanked.
3) Adjust the border line of blanked picture
coincident with the mechanical center marks
of the CRT using the V-CENTER UP/DOWN KEY.
6.2 VERTICAL SIZE

The VERTICAL CENTER adjustment
has to be done in advance.
3) Adjust the upper part of the picture
with the V-SIZE UP/DOWN keys.
6.3 VERTICAL SLOPE

The VERTICAL SIZE adjustment
has to be done in advance.
2) Adjust the lower part of the picture
with the V-SLOPE UP/DOWN keys.
6.4 VERTICAL S-CORRECTION

1) Apply a CROSSHATCH PATTERN signal.
2) Adjust the S-COR UP/DOWN KEY to obtain
the same distance between horizontal lines.
6.5 HORIZONTAL CENTER

2) Adjust picture centering with H-CENTER
LEFT/RIGHT keys.
5
If EEPROM(1703) has been changed ;

- Option data has to be changed and
- all alignment function has to be readjusted.
The initial state of adjustment are as follows;
- V-Center, V-Slope V-Size, H-Center, R, G, B, AFT = Center (30/64 - 33/64)
- S-Correction = 00/64
- AGC = 15~60/64
Service Remocon
6
IC Description
DW370ASM* (Micro-controller for Non-Teletext Model)
=TMS370C08A05 ( TI Type No.)
(1) General Description
The TMS370C08A05 devices are members of the cMCU370 family single-chip microcontrollers.
The cMCU370 family provides cost effective real-time system control through use of the PRISM methodology.
The PRISM methodology modular fabrication process integrates analog, digital, linear and power technologies on a
single chip, thereby maximizing the total integration strategy.
The TMS370C08A05 devices are designed with the high-performance 8-bit TMS370C8 CPU.
Features of the C8 CPU and system module as implemented on this device include three CPU registers (stack
pointer, status register, and the program counter), two external interrupts, reset, memory mapped control registers.
(2) Feature
Internal Memory Configurations
- 16K-Byte ROM Program Memory
- 512-Byte RAM
Operating Features
- Supply Voltage (VCC) 5 V 10%
- Input Clock Frequency 2, 20MHz
- Industrial Temperature Range
Device Integrity Features
- Address Out-of-Range Reset
- Stack Overflow Reset
- Parallel Signature Analysis (CRC)
Two 16-Bit General Purpose Timer(T8A)
Each Includes:
- 16-Bit Resettable Counters with individual 8-Bit Prescaler
- 2 PWM Channels or
- 2 Input Captures or
- 1 Input Capture and 1 PWM Channel
One 14-Bit PWM Module
- 14-Bit Resettable Counters
- 14-Bit PWM Output Port
One 8-Bit PWM Module
- 8-Bit Resettable Counters
- 8-Bit PWM Output Port with 12V Open Drain
OSD Module
- Blanking/ Contrast reduction out
- Transparent Background
- Transparent Foreground
- Full Screen Background Color
- Controlled Color, Blink, Size, Smoothing, Fringe of Each lines of Character
- Two size of different Font 12x10 and 12x18 by Hard Masking
- OSD Window Display with 40x25 lines
8-Bit A/D Converter With 3 Inputs
- Single or Dual Channel Operation
- Single or Continuous Conversion Modes
Flexible Interrupt Handling
- Global and Individual Interrupt Masking
- 2 S/W Programmable Interrupt Levels
- 2 External Interrupt (1 Non-Maskable)
- Programmable Rising or Falling Edge Detect
7
09 CMOS Compatible I/O Pins

- All Peripheral Function Pins Software Configurable for Digital I/O
- 6 Bidirectionals, 3 Input Pins
Plastic 42 YSDP Pins Package
(3) Block Diagram
8
DW5255M*(Micro-controller & West/East Teletext Decoder)

DW5255RM*(Micro-controller & Cyrillic Teletext Decoder)
=SDA5255-A*** (SIEMENS Type No.)
The TDA5255 contains a slicer for VPS and TTX, an accelerating acquisition hardware module, a display
generator for LEVEL 1 TTX data and a 8 bit u-controller running at 333 nsec cycle time.
The controller with dedicated hardware guarantees flexibility, does most of the internal processing of TTX
acquisition , transfers data to/from the external memory interface and receives/transmits data via I2C and
UART user interfaces.
The Slicer combined with dedicated hardware stores TTX data in a VBI 1Kbyte buffer.
The u-controller firmware does the total acquisition task (hamming- and parity -checks,
page search and evaluation of header control bits) once per field.
(2) Feature
Acquisition:
- feature selection via special function register
- simultaneous reception of TTX and VPS
- fixed framing code for VPS and TTX
- programmable framing code window for TTX
- Acquisition during VBI
- direct access to VBI RAM buffer
- Acquisition of packets x/26, x/27, 8/30 (firmware)
- assistance of all relevant checks (firmware)
- 1-bit framing-code error tolerance (switchable)
Display:
- features selectable via special function register
- 50/60 Hz display
- level 1 serial attribute display pages
- blanking and contrast reduction output
- 8 direct addressable display pages
- 12 x 10 character matrix
- 96 character ROM (standard G0 character set)
- 143 national option characters for 11 languages
- 288 characters for X/26 display
- 64 block mosaic graphic characters
- 32 free addressable characters for OSD in expanded character ROM + 32 inside OSD box
- double height (TOP/BOTTOM)
- conceal/reveal
- transparent foreground/background -inside/outside of a box
- cursor (colour changes from foreground to background colour)
- flash (flash rate 1s)
- programmable horizontal und vertical sync delay
- hardware assisted fast display page erase
- full screen background colour in outer screen
Synchronization:
display synchronization to sandcastle or Horizontal Sync (HS) and Vertical Sync (VS) with startstop-oscillator or
display synchronization to sandcastle or Horizontal Sync and Vertical Sync with external clock
independent clock systems for acquisition, display and controller
9
Controller:
- 8 bit configuration
- 18 MHz internal clock
- 0.33 us instruction cycle
- eight 16-bit data pointer registers (DPTR)
- two 16-bit timers
- watchdog timer
- serial interface (UART)
- 256 bytes on-chip RAM
- 1 Kbyte on-chip extended RAM (access via MOVX)
- 8 Kbyte on-chip ACQ-buffer-RAM (access via MOVX)
- 6 channel 8-bit pulse width modulation unit
- 2 channel 14-bit pulse width modulation unit
- 4 multiplexed ADC inputs with 8-bit resolution
- one 8-bit I/O port with open drain output and optional I2C emulation
- two 8-bit multifunctional I/O ports
- one 4-bit port working as digital or analog inputs
- one 2-bit I/O port with optional address latch enable function
P-SDIP 52 package
5 V supply voltage
(3) Block Diagram
10
(4) Pin Description

* A : DW5255M*/DW5255RM*, *B : DW370ASM*
Pin
Name
A*
B*
A*
B*
P3.1
T1IC1/CR
Symbol
SYS
Description
A*
B*
NTSC OUT for switching SAW filter

K6259
- PAL/SECAM : L
- NTSC : H
P0.7/Open Drain
A0
BUSSTOP
I2C BUS STOP IN for Computer

controlled alignment in Factory
( Active Low )
P0.6/Open Drain
A1
SDA
Serial data IN/OUT for I2C
P0.5/Open Drain
A2
SCL
Serial clock IN/OUT for I2C
P0.4/Open Drain
A3
OPTION
#5 #6 Teletext
P0.3/Open Drain
A4
OPTION
H H West Teletext
H : STAND-BY
L H East Teletext
L : POWER ON
H L Turkish Teletext
P0.2/Open Drain
A5
OPTION
Not Used
P0.1/Open Drain
PWM1-0/ Open Drain
OPTION
Not Used
P0.0/Open Drain
PWM1-1/ Open Drain
LED
LED drive OUT

- Stand-by mode : H
- Operating mode : L
( IR reception : pulse )
10
10
VSS
VSS
ground
11
11
VCC
VCC
Power Supply
12
12
XTAL1
OSCIN
OSCIN
Input to inverting osc. Amplifier
13
13
XTAL2
OSCOUT
OSCOUT
Output of inverting osc. Amplifier
14
14
P4.0/ALE
PWM1-2/Open Drain
15
15
RESET
RESET/Open Drain
RST
RESET IN (ACTIVE LOW)
16
16
P1.7/14BIT PWM
PWM2-0
VT
TUNING VOLTAGE OUT
17
17
P1.6/14BIT PWM
PWM2-1
SW
H : I/M
L : B/D
18
18
P1.5/8BIT PWM
PWM1-3/Open Drain
F/SW
Not Used
19
19
P1.4/8BIT PWM
PWM1-4/Open Drain
20
20
P1.3/8BIT PWM
PWM1-5/Open Drain
MUTE
AUDIO MUTE OUT
21
21
P1.2/8BIT PWM
TEST
GND
(Must be tied 0V for DW370M*)
Not Used
#6
H : I/M, L : B/D
Not Used
Not Used
22
P1.1/8BIT PWM
Not Used
23
P1.0/8BIT PWM
24
VSSA
VSSA
Analog GND for Slicer
25
FIL3
FIL3
PLL Loop Filter I/O for Phase Shifting
26
FIL2
FIL2
PLL Loop Filter I/O for TTX Slicing
27
FIL1
FIL1
PLL Loop Filter I/O for VPS Slicing
28
VCCA
VCCA
Analog Supply for Slicer
29
IREF
IREF
Reference Current for Slicer PLLs
Not Used
11
Pin
A*
Name
B*
A*
30
CVBS
31
P2.3/8 bit ADC
B*
Symbol
CVBS
Description
A*
B*
CVBS IN
Not Used
32
22
P2.2/8 bit ADC
B0/AN0/ADC
AGC
33
23
P2.1/8 bit ADC
B1/AN1/ADC
KS
Local KEY SCAN IN
34
24
P2.0/8 bit ADC
B2/AN2/ADC
S/SW
Not Used
35
25
VSS
VSS-OSD
VSS
Ground
36
26
P3.3/INT1
INT1
IR
REMOTE IR IN
37
27
VDD
VCC-OSD
VDD
Power Supply
38
28
LCIN
OSCIN-OSD
LCIN
CLOCK IN for OSD
39
29
LCOUT
OSCOUT-OSD
LCOUT
CLOCK OUT for OSD
40
30
P3.7/TXT I/O
T2EVT/PWM2
BL
BAND VHF-L OUT ( Active High )
41
31
P3.6/RXD
T2IC2/PWM1
BH
BAND VHF-H OUT ( Active High )
42
32
P3.5/T1
T2IC1/CR
BU
BAND UHF OUT ( Active High )
43
33
P3.4/T0
T1EVT/PWM2
POWER
POWER CONTROL OUT
44
34
P3.2/INT0
INT2
45
35
HS/SC
HSYNC
HSYNC
HOR. SYNC. IN
(Active High)
46
36
P4.7/VS
VSYNC
VSYNC
VERT. SYNC. IN
(Active High)
47
37
RED OUT
48
38
GREEN OUT
49
39
BLUE OUT
50
40
BLANK
BL
BLANK OUT
51
41
COR
COR
Not Used
(CONTRAST REDUCTION OUT)
52
42
P3.0
EVEN/ODD
EVEN/ODD OUT for non-interlacing

in TTX mode
T1C2/PWM1
Not Used
12
IF AGC INPUT for Auto Tuning System
24LC08B (EEPROM)
(1) Features
Single supply with operation down to 2.5V
Low power CMOS technology
- 1mA active current typical
- 10 A standby current typical at 5.5V
- 5 A standby current typical at 3.0V
Organized as two or four blocks of 256 bytes
(2x256x8) and (4x256x8)
Two wire serial interface bus, I2CTM compatible
Schmitt trigger, filtered inputs for noise suppression
Output slope control to eliminate ground bounce
100KHz(2.5V) and 400KHz(5V) compatibility
Self-timed write cycle(including auto-erase)
Page-write buffer for up to 16 bytes

2ms typical write cycle time for page-write
Hardware write protect for entire memory
Can be operated as a serial ROM
Factory programming(QTP) available
ESD protection > 4,000V
1,000,000 ERASE/WRITE cycles(typical)
Data retention > 40 years
8-pin DIP, 8-lead or 14-lead SOIC packages
Available for extended temperature ranges
- Commercial : 0 C to +70 C
-Industrial : -40 C to +85 C

The Microchip Technology Inc. 24LC08B is a 8K-bit Electrically Erasable PROM.
The device is organized as four blocks of 256x9bit memory with a two wire serial interface. Low voltage
design permits operation down to 2.5 volts with standby and active currents of only 5 A and 1mA respectively.
The 24LC08B also has a page-write capability for up to 16 bytes of data.
The 24L08B is available in the standard 8-pin DIP surface mount 80IC packages.
(3) Block Diagram
WP
I/O
CONTROL
LOGIC
MEMORY
CONTROL
LOGIC
HV GENERATOR
XDEC
EEPROM ARRAY
(4X256X8)
PAGE LATCHES
SDA
SCL
YDEC
VCC
VSS
SENSE AMP
R/W CONTROL
(4) Pin Description

PIN
SYMBOL
DESCRIPTION
1-3
A0, A1, A2
Device Address lnputs
Vss
Ground
SDA
Serial Data/Address
SCL
Serial Clock
WP
Vcc
+5V Power supply
13
TDA8374A (Single chip TV Processor for Negative modulation IF )

TDA8374 (Single chip TV Processor for Negative & positive modulation IF)
The TDA8374(A) is I2C-bus controlled single chip TV processors which are intended to be applied in PAL/NTSC
television receiver.
The IC is mounted in a S-DIL 56 envelope.
(2) Feature
IF
- Vision IF amplifier with high sensitivity and good figures for differential phase and gain
- PLL demodulator with high linearity offering the possibility for (single standard) intercarrier stereo audio application .
- Alignment PLL via I2C
- [TDA8374] Multistandard IF with negative and positive modulation, switchable via I2C
AUDIO
- Alignment free multi standard PLL audio demodulator (4.5 to 6.5 MHz.)
- Mono volume control
Video
- Integrated luminance delay line
- Integrated chroma trap and bandpass filters (auto calibrated)
- Asymmetrical peaking circuit in the luminance channel
- Black stretching of non standard CVBS or luminance signals
Colour
- SECAM interface for application with SECAM add-on TDA8395.
RGB
- RGB control (brightness, contrast, saturation)
- Black current stabilization and white point adjustment
Input / Output
- Flexible video source select with CVBS input for the internal signal and two external video inputs(one switchable for
CVBS or Y/C).
- The output signal of the video source select is externally available ( also as CVBS when Y/C input is used).
- External audio input.
- Linear RGB input with fast blanking.
Synchronization and Deflection
- Horizontal synchronization with two control loops and alignment free horizontal oscillator.
- Slow start and slow stop of the horizontal drive output to enable low stress start-up and switch-off from the line
circuit at nominal line supply voltage.
- Vertical count-down circuit for stable behavior with provisions for non-standard signals.
- Vertical geometry control.
- Vertical drive optimized for DC coupled vertical output stages.
Control
- Full I2C bus control, as well for customer controls as for factory alignment.
- All automatic controls have an option for forced mode.
Power consumption
- Low power consumption (900 mW at 8.0 Volts).
Packaging
- SDIL-56 (Shrinked Dual In Line, 56 pins).
14
(3) Block Diagram
15
(4) Pin Description

No
1
Name
SOUND IF INPUT
EXT AUDIO INPUT
3
4
VCO REF FILTER
PLL LOOP FILTER
IF VIDEO OUTPUT
7
8
9
BUS INPUT : SCL

BUS INPUT : SDA
BANDGAP
DECOUPLING
10
CHROMA INPUT
11
12
37
Y/CVBS INPUT
MAIN
POSITIVE SUPPLY
Description
The sound equivalent input impedance is 8k5 ohm // 5pF which has to be
taken into account for proper termination of the ceramic filters.
The DC impedance is very high.
The minimum input signal for catching is l mV rms.
An external sound signal (500mVrms) for example from SCART can be
applied to this pin via a coupling capacitor.
The input impedance is 25kohm.
The IF VCO tuned circuit is applied to these pin.
Its resonance frequency must be two times the IF-frequency and in between a
range of 64-120MHz.
This range is suitable for the IF standards as 33.4, 38.9, 45.75 and 58.75MHz.
The VCO frequency can be adjusted by I2C bus so a fixed coil can be used.
The PLL loopfilter is a first order filter with R=390 ohm and C = 100nF in
series to ground.
The loopfilter bandwidth is 60kHz and is optimal for both fast catching and
sufficient video suppression for optimal sound performance.
Sound performance can theoretically be improved by adding a small
capacitor (approx.0- 4.7nF) between pin 5 and ground.
This however must be evaluated further because the normal video signal
response should not be effected.
Although the video output impedance is low it is recommended to avoid
high frequency current in the output due to for instance sound trap filters.
This can be achieved by means of an emitter follower at the video output with
a 1 resistor in series with the base.
Serial clock line
Serial data line
The bandgap circuit provides a very stable and temperature independent
reference voltage.
This reference voltage (6.7V) ensures optimal performance of the TDA8374
and is used in almost all functional circuit blocks.
The supplied C S-VHS input burst amplitude should be nominally 300mVpp
(assumed is a colour bar signal with 75% saturation and with chroma/burst
ratio of 2.2/1 ). The C S-VHS input is internally clamped to 4V via 50 .
The external AC coupling capacitor with 50 forms a high pass filter.
A recommended coupling capacitor is 1 nF; the high pass filter cut off
frequency is then approximately 3KHz.
The Y S-VHS signal of 1Vpp ( inclusive sync amplitude) is AC coupled to pin11.
The TDA8374 has a main supply pin 12 and a horizontal supply pin 37. Both
pins have to be supplied simultaneously.
Notice that the IC has not been designed to use this pin 37 as start pin.
(pin 37 supplies the horizontal oscillator, PHI-1 and PHl-2)
(pin 12 supplies the rest of the circuits in the IC)
The nominal supply voltage is 8V. With min/max values of 7.2-8.8V.
Also in stand-by condition the IC must be supplied with 8V.
16
No
Name
13
17
INT CVBS INPUT

EXT CVBS INPUT
14
15
GROUND
AUDIO OUTPUT
16
DECOUPLING
FILTER TUNING
18
BLACK CURRENT
INPUT
BLUE OUTPUT
GREEN OUTPUT
RED OUTPUT
19
20
21
22
V-GUARD INPUT/
BEAM CURRENT
LIMITER
23
24
25
26
RED INPUT
GREEN INPUT
BLUE INPUT
RGB INSERTION
SWITCH INPUT
27
LUMINANCE INPUT
Description
A voltage detection circuit is connected to both pins.
- pin12 if V12 <6.8V than a power on reset, POR, is generated. The Hout
output is disabled immediate.
- pin37 if V37 <5.8V than the horizontal output is disabled immediate.
It is recommended that the CVBS1 int and CVBS2 ext input amplitudes are
1 Vpp (inclusive sync amplitude).
This, because the noise detector switches the 1 loop to slow mode
(i.e. auto 1mode when FOA, FOB = 0,0) when noise level exceeds
100mVrms (i.e. at S/N of 20dB).
All internal circuits are connected to this ground pin 14.
The output signal is volume controlled and is active for both internal and
external audio signals. The nominal gain is +9dB and -71dB, which gives
a total control range of 80dB.
The output signal range therefor is 0.14- 1400mVrms
The bandwidth is >100kHz, the DC level is 3.3V and the output impedance
is 250 .
Voltage variations at pin 16, which can be due to external leakage current or
crosstalk from interference sources, should be less than 50mV to ensure that
tuning of filters/delay cells remains correct.
For correct operation of the loop CURRENT information is supplied to the
black current input pin.
The RGB outputs are supplied to the video output stages from pins 21, 20
and 19 respectively.
For nominal signals (i.e. CVBS/S-VHS, -(R-Y)/- (R-Y), TXT inputs) and for
nominal control settings, then the RGB output Signal amplitudes is
typically 2VBLACK_WHITE.
Vertical Guard
With this function, the correct working of the vertical deflection can be
monitored. If the vertical deflection fails, the RGB outputs are blanked to
prevent damage to the picture tube.
Beam current limitinq
The beam current limiting function is realised by reducing the contrast (and
finally the brightness) when the beam current reaches s too high level. The
circuit falls apart in two functions:
- Average beam current limiting (ABL): reacting on the average content of
the picture
- Peak white limiting (PWL): reacting on high local peaks in the RGB signal.
The Rin, Gin, Bin input signals (nominal signal amplitude of 700mV) are
AC coupled to pin 23, 24 and 25 respectively.
Clamping action occurs during burstkey period.
The table below a survey is given of the three modes which can be selected
with a voltage on RGB insertion switch input pin ;
Vpin26
I2C function Selected RGB signal
0.9V-3V IE1=0
RGB(internal)
IE1=1
Rin,Gin,Bin
(fast insertion on pin23,24,25)
> 4V
IE1=X
OSD can be inserted at the RGBout pins
An nominal input signal amplitude of 1 Vblack-white MUST be DC coupled
17
No
Name
28
29
30
LUMINANCE
OUTPUT
B-Y OUTPUT
R-Y OUTPUT
31
32
B-Y INPUT
R-Y INPUT
33
SECAM REF
OUTPUT
X-TAL 3.58
X-TAL 4.43
34
35
36
38
39
40
LOOP FILTER
BURST PHASE
DETECTOR
CVBS OUTPUT
BLACK PEAK
HOLD CAPACITOR
HOR OUTPUT
41
SANDCASTLE
OUTPUT/
FLYBACK INPUT
42
PHI-2 FILTER /
FLASH PROTECT
Description
to the luminance input pin 27.
The pin is internally AC coupled to the luminance clamp via a capacitor of
50pF; clamping action occurs during burstkey period.
The luminance output signal is approximately l V black-white with typical
output impedance of 25O ohm.
The maximum output impedance of pins 29 and 30 is 500 when PAL/NTSC
signals are identified. When SECAM is identified by the SECAM add-on and
no PAL/NTSC is already identified by the ASM, then the ASM sets the
-(B-Y)/-(R-Y) output switch open (via DEMSW).
This enables the -(B-Y)/-(R-Y) outputs of the TDA8395 to be directly connected
to pins 29 and 3O respectively.
The -(B-Y),-(R-Y) output signals (supplied from baseband delay line) are AC
coupled, via a coupling capacitor of 10nF or greater, to the -(B-Y)/-(R-Y) inputs;
both inputs are clamped during burstkey period.
The SECAM reference output is directly connected to pin l of the TDA8395 for
SECAM decoding ; it also can be used as a reference for comb filter applications.
To ensure correct operation of both:
- colour processing internal circuits,
- sync calibration internal circuits,
it is only allowed to have 3.6MHz Xtals on pin34: both 4.4MHz,3.6MHz Xtals
are allowed on pin 35.
If pin 35 is not used: then it is left open in application (also XA,XB=O,1 ).
One of the important aspects of the PLL is the 1oop filter connected to pin 36;
it influences the dynamic performance of the loop.
The output amplitude is 1Vpp (transfer gain ratio between CVBS1int or
CVBS2ext or CVBS3ext/Ys-vhs and CVBSout is 1).
The maximum output impedance is 250 ohm.
For the correct working of the black stretcher an external time constant should
be added at the black peak hold capacitor input.
This open collector output is meant to drive the horizontal output stage.
The output is active low, i.e. the line transistor should conduct during the low
period of the output.
Pin 41 is a combined input/output pin.
The pin provides a three level sandcastle pulse.
Both burstkey pulse and vertical blanking pulse are always available, the line
blanking pulse is only present when the external flyback pulse is fed to this pin.
The line flyback pulse, fed to this pin is used for two functions:
- input signal for the PHI-2 1oop and
- RGB line blanking. (without flyback pulse blanking occurs only during the
burstkey pulse)
To ensure correct working of the delay line and SECAM add-on, the output
should not be loaded with more than:
- Sandcastle input delay line TDA 4665
- Sandcastle input SECAM add-on TDA 8395
The loopfilter is a first order filter.
This pin requires a capacitor (C) only.
18
No
Name
43
PHI-1 FILTER
44
45
46
47
GROUND
EAST-WEST DRIVE
VERT DRIVE +
VERT DRIVE -
48
49
IF INPUT
50
EHT/OVERVOLTAGE
PROTECT INPUT
VERT
SAWTOOTH
CAPACITOR
51
52
53
54
REFERENCE
CURRENT INPUT
AGC
DECOUPLING
CAPACITOR
TUNER AGC
OUTPUT
55
AUDIO
DEEMPHASSIS
56
DECOUPLING
SOUND
DEMODULATOR
Description
A flash protection becomes active when this pin is forced >6V. The horizontal
drive is switched-off immediately.
Once the voltage is <6V the horizontal drive is switched-on again via the slow
start procedure.
The loopfilter connected to pin 43 is suitable for various signal conditions as
strong/weak and VCR signal.
This is achieved by switching of the loopfilter time constant by changing the
PHI-1 output current.
Via I2C bus FOA/B, different time constants can be chosen, including an
automatic mode which gives optimal performance under varying conditions.
To this pin are connected the IC-substrate and horizontal output.
not used
The vertical drive has a current output. The output is balanced which ensures
a good common mode behavior with temperature and makes the output signal
less sensitive for disturbances.
The PLL frequency range is 32-60MHz with corresponding VCO frequency
64-120MHz.
The IF input impedances is 2 in parallel with 3pF and matches the required
load for commonly used SAW filters.
A DC coupling is allowed, so no series capacitors between SAW filter and IF
input are necessary.
not used
This pin requires a capacitor to ground of l00nF +, - 5%.
The optimal sawtooth amplitude is 3.5V and is determined by the external
capacitor and charge current.
The sawtooth bottom-level is 2V.
This pin requires a resistor to ground.
The optimal reference current is 100 . which is determined by this resistor.
The AGC capacitor value is 2.2 and has been defined for an optimal
compromise between AGC speed and tilt for all AGC modes
(negative/positive modulation).
This output is used to control (reduce) the tuner gain for strong RF signals.
The tuner AGC is an open collector output which is acting as a variable
current source to ground.
Only a capacitor has to be connected to this pin that defines the deemphasis
time constant.
The signal is internally connected through to the Audio switch.
The deemphasis output is fixed, thus not controlled by the volume, and can be
used for SCART.
This pin requires a capacitor of 10 connected to ground.
The pin acts as a low pass filter needed for the DC feedback loop.
19
TDA4665(Base Band Delay Line)

(1) Features
Two comb filters, using the switched-capacitor technique,for one line delay time (64s)
Adjustment free application
No crosstalk between SECAM colour carriers
Handles negative or positive colour-difference input signals
Clamping of AC-coupled input signals((R-Y)and(B-Y))
VCO without external components
3MHz internal clock signal derived from a 6MHz VCO, line-locked by the sandcastle pulse (64s line)
Sample-and -hold circuits and low-pass filters to suppress the 3 MHz clock signal
Addition of delayed and non-delayed output signals
Output buffer amplifiers
Comb filtering functions for NTSC colour-difference signals to suppress cross-colour
The TDA4661 is an integrated baseband delay line circuit with one line delay. It is suitable for decoders
with colour-difference signal outputs(R-Y)and(B-Y).
(3)Block Diagram
(4) Pin Description

SYMBOL PIN
SYMBOL PIN
DESCRIPTION
DESCRIPTION
Vp2
+5V supply voltage for digital part
Vp1
+5V supply voltage for analog part
n.c.
not connected
GND1
10
ground for analog part (0V)
GND2
ground for digital part (0V)
V0 (R-Y)
11
(R-Y) output signal
i.c.
internally connected
V0 (B-Y)
12
(B-Y) output signal
SAND
sandcastle pulse input
n.c.
13
not connected
n.c.
not connected
V1 (B-Y)
14
(B-Y) input signal
i.c.
n.c.
15
not connected
i.c.
V1 (R-Y)
16
(R-Y) input signal
20
TDA8395 (Secam Decoder)

(1) Features
Fully integrated filters
Alignment free
For use with baseband delay
(2) Description
The TDA8395 is a self-calibrating,fully integrated SECAM decoder. The IC should preferably be used
in conjunction with the PAL/NTSC decoder TDA8362 and with the switch capacitor baseband delay
circuit TDA4665. The IC incorporates HF and LF filters, a demodulator and an identification circuit
(Iuminance is not processed in this IC).
A highly stable reference frequency is required for calibration and a two-level sandcastle pulse for
blanking and burst gating.
(3) Block Diagram
PLLref
CLOCHEref
GND
TEST
Vp
100 nF
220 nF
BANDGAP
TUNING
TUNING
TDA8395
CVBS
16
ACC
CLOCHE
FILTER
PLL
INTERFACE
CONTROL
IDENTIFICATION
DEEMPHASIS
9
OUTPUT
STAGE
(R-Y)
10
(B-Y)
1
fref/IDENT
(4) Pin Description

SYMBOL
PIN
fp1/IDENT
1
TEST
2
Vp
3
n.c.
4
n.c.
5
GND
6
CLOCHEref
7
PLL ref
8
-(R-Y)
9
-(B-Y)
10
n.c.
11
n.c.
12
n.c.
13
n.c.
14
SAND
15
CVBS
16
15
SAND
DESCRIPTION
reference frequency input/identification input
test output
positive supply voltage
not connected
not connected
ground
Cloche reference filter
PLL reference
-(R-Y) output
-(B-Y) output
not connected
not connected
not connected
not connected
sandcastle pulse input
video (chrominance) input
21
TDA6106Q ( Video Output Amplifier )

The TDA6106Q is a monolithic video output amplifier (5MHz bandwidth) in a SIL 9 MPpackage, using high-voltage
DMOS technology, and is intended to drive the cathode of CRT directly .
To obtain maximum performance, the amplifier should be used with black-current control.
(2) Feature
Black - current measurement output for automatic black current stabilization (ABS)
Single supply voltage of 200V
Internal protection against positive appearing CRT flash-over discharge
Protection against ESD
Internal 2.5V reference circuit
Controllable switch-off behavior
(3) Block Diagram
(4) Pin Description

PIN
SYMBOL
DESCRIPTION
N.C
N.C
V in
inverting input
GND
ground, substrate
I om
Black-current measurement output
V dd
supply voltage high
N.C
V oc
cathode output
V of
feedback/transient output
22
I802 PC817
The specification applies to the structures and characteristics of Model No. PC817
(2) Block Diagram
(3) Absolute maximum ratings
Input
Output
Parameter
Symbol
Forward current
IF
*1) Peak forward current
IFM
Reverse voltage
VR
Power dissipation
70
mW
Collector-emitter voltage
VCEO
35
Emitter-collector voltage
VECO
Collector current
IC
50
mA
Collector power dissipation
Rating
50
Unit
mA
Pc
150
mW
Total Power dissipation
Ptot
200
mW
Operating temperature
Topr
-30~+100
Storage temperature
Tstg
-55~+125
*2) Isolation voltage
Viso
*3) Soldering temperature
Tsol
260
*1) Pulse width 100 s, duty ratio: 0.001

*2) AC for 1 minute, 40~60% RH
*3) For 10 seconds.
23
kVrms
C
TDA8356 (DC-coupled vertical deflection circuit)

The TDA8356 is power circuit for use in 90 and 110 color deflection systems for field frequencies of 50 to 120 Hz.
The circuit provides a DC driven vertical deflection output circuit, operating as a high efficient class G system.
(2) Feature
High efficient fully DC-coupled vertical output bridge circuit
Vertical fly-back switch
Guard circuit
Protection against : - short circuit of the output pins (7 and 4)
- short circuit of the output pins to Vp
Temperature (thermal) protection
High EMC immunity because of common mode inputs
(3) Block Diagram
(4) Pin Description

PIN
SYMBOL
DESCRIPTION
I drive (pos)
input power stage (positive); include Ii(sb) signal bias
I drive (neg)
input power stage (negative); include Ii(sb) signal bias
Vp
operating supply voltage
V o(b)
output voltage B
GND
ground
V fb
input fly-back supply voltage
V o(a)
output voltage A
V o(guard)
guard output voltage
V I(fb)
input feedback voltage
24
TDA7056 (BTL AUDIO OUTPUT AMPLIFIER) : 1 SPEAKER MODEL

(1) Features
No external components
No switch-on/off clicks
Good overall stability
Low power consumption
Short circuit proof
ESD protected on all pins
The TDA7056 is a mono output amplifier contained in a 9 pin medium power package.
The device is designed for batteryfed portable mono recorders, radios and television.
(3)Block Diagram
(4)Pin Description
PIN
DESCRIPTION
n.c.
Vp
input (+)
signal ground
n.c.
output (+)
power ground
output (-)
n.c.
25
STR-S5707 (Hybrid IC for a Switching Regulator)

The STR-S5707 is a Hybrid IC with a built in power transistor and a separate excitation control IC,
designed for converter type switching mode power supply applications.
The IC is capable of quasi-resonant mode and requires small number of external component.
(2) Feature
Small SIP isolated package : Resin sealed type (transfer mold)
Lower power dissipation at a lighter load
Many protection function : - Pulse-by-pulse over current protection
- Over-voltage protection with a latch
- Thermal protection with a latch
These protection functions are incorporated and can be latched with an external signal.
(3) Block Diagram
(4) Pin Description

PIN
NAME
SYMBOL
DESCRIPTION
Collector
Collector of power Tr
Ground
GND
ground (Emitter of power Tr)
Base
Base of power Tr
Sink
SINK
Base current (IS) input
Over-current
protection
OCP
over-current sensing signal input
Inhibit
Latch
INH
input for synchronizing OFF time

and latch circuit operation
Sensing
SENS
constant voltage control signal input
Drive
DRIVE
Base drive current (ID) output
Vin
VIN
supply voltage for control circuit

26
Electrical Characteristics of Control Part (Ta=25 )

Description
Terminal
Symbol
MIN
TYP
MAX
On-state Voltage
9-2
VIN(ON)
7.6
8.4
Off-state Voltage
9-2
VIN(OFF)
4.6
4.9
5.2
Operating Circuit Current
9-2
IIN(ON)
15
28
mA
9-2
IIN(OFF)
200
Stand-by Circuit Current
Rating
Unit
On Time
TON
33
41
Off Time
TOFF
45
55
OCP terminal Threshold Voltage
6-2
VOCP
-1.12
-1
INH terminal Threshold Voltage 1
8-2
VINH-1
0.65
0.75
0.85
8-2
VINH-2
1.4
2..0
8-2
VLatch
3.2
5.1
5.8
OVP Operating Voltage
9-2
VIN(OVP)
9.2
10.7
Latch Circuit Sustaining Current
9-2
IH
500
9-2
VIN(La.OFF)
2.5
3.1
Tj(TSD)
125
150
Latch Circuit Cancellation Voltage

MIC Thermal Shutdown
Starting Temp
Fixed Reference Voltage
7-2
Temperature Coefficient of
Reference Voltage
7-2
VS
-0.88
32.0
+2.5
mV/
Electrical Characteristics of Power Transistor Part(Trl) (Ta=25 )

Description
Terminal
Symbol
Rating
Collector Saturation Voltage
1-2
VCE(sat)
0.4
Collector Cutoff Current
1-2
ICEX
100
Base-Emitter saturation voltage
3-2
VBE(sat)
1.5
MIN
DC Current Gain
hFE
Thermal Resistance
Switching Time
j-F
MAX
61
1.3
1-2
ts
15
1-2
tf
0.5
27
29
TYP
Unit
/W
TDA8138 (5.1V+12V regulator with Disable and Reset)

The TDA8138 is a monolithic dual positive voltage regulator designed to provide fixed precision output voltages of
5.1V and 12V at currents up to 1A.
A internal reset cuicuit generates a reset pulse when the output 1 decrease below the regulated voltage value.
Output 2 can be disabled by TTL input.
Shot circuit and themal protections are included.
(2) Feature
output currents up to 1A
ixed precision Output 1 voltage 5.1V 2%
fixed precision Output 2 voltage 12V 2%
output 1 with Reset facility
output 2 with Disable by TTL input
short circuit protection at both outputs
thermal protection
low drop output voltage
(3) Block Diagram
(4) Pin Description

PIN
SYMBOL
DESCRIPTION
V in 1
input 1
V in 2
input 2
Ce
Delay capacitor
V dis
disable
GND
ground
RST
reset
28
n.c
V out 2
output 2 (12V)
V out 1
output 1 (5.1V)
TDA 1519B(AUDIO OUTPUT AMPLIFIER); 2 SPEAKER MODEL

(1) Features
Requires very few external components for
Bridge Tied Load(BTL)
Stereo ot BTL application
High output power
Low offset voltage at output (important for BTL)
Fixed gain
Good ripple rejection
Mute/stand-by switch
Load dump protection
AC and DC short-circuit-safe to ground and Vp

Thermally protected
Reverse polarity safe
Capability to handle high energy on
outputs(Vp=OV)
No switch-on/switch-off plop
Protected against electrostatic discharge
Identical inputs(inverting and non-inverting)
Compatible with TDA 1519A(except output power)

The TDA 1519B is an integrated class-B dual output amplifier in a 9-lead single in-line(SIL) plastic
medium power package. The device is primarily developed for car radio applications.
(4) Pin Description
(3) Block Diagram
PIN
1
2
3
4
5
6
7
8
9
Mute Switch
1
Cm
60k
VA
133
Power Stage
18.1k
Vp
8
Stand-by
Switch
Stand-by
Reference
Voltage
VA
15k
+
+
-
1
3
15k
Mute
Switch
Mute
Reference
Voltage
TDA1519B
18.1k
Power Stage
183
6
VA
Cm
60k
Mute Switch
Input
Reference
Voltage
Signal
Ground
Vp
Power
Ground
(Substrate)
29
SYMBOL
NINV
GND1
RR
OUT1
GND2
OUT2
Vp
M/ss
INV
DESCRIPTION
non-inverting input
ground(signal)
supply voltage ripple rejection
output 1
ground(substrate)
output 2
positive supply voltage
mute/stand-by switch
inverting input
PCA84C 122A(IC REMOCON)

(1) Features
ROM, RAM and I/O is device dependent
Two test inputs T0, T1
3 Single-level vectored interrupt sources
8 bit programmable timer/counter with 5-bit pre-scaler
Single supply voltage from 2.0V to 5.5V
On-board oscillator 1MHz to 5MHz
Operating temperature range -20 to +50 C
The PCA84C122A is a stand-alone micro controller designed for use in remote control unit for a wide
range of applications.
(3) Pin Description
PIN
3
2
23
22
10
11
14
15
19
18
17
16
1
24
12
13
4
5
6
SIGNAL
P00
P01
P02
P03
P04
P05
P06
P07
P10
P11
P12
P13
P14
P15
P16
P17
TP/INT
T1
RESET
8
9
21
7
20
XTAL 1
XTAL 2
OUT
VDD
Vss
DESCRIPTION
Standard I/O Port lines, generally used for keypad scanning
Standard I/O Port lines, generally used for keypad scanning
Test T0 and external interrupt input

Test T1
Active HIGH reset, normally tied to Vss because internal
Power-on reset can serve the same function
Crystal or ceramic resonator
Pulse train output pin, capable of sinking 27mA
Power supply
Ground
30
Circuit Description
Vision IF amplifier, AFC, video demodulator
The IF signal from the tuner is fed through a SAW filter to the differential IF input (pin 48 and 49).
The first IF stage consists of 3 AC-coupled amplifiers with a total gain control range of over 66 dB.
The reference carrier for the video demodulator is obtained by a PLL carrier regenerator
(eliminating notch filter compromises, as in reference tuned circuits for passive carrier regeneration).
Only an oscillator coil is needed( pin 3 and 4) that can be aligned via l2C-bus to the double IF frequency.
The AFC information is derived from the VCO control voltage of the IF-PLL
and can be read via I2C-bus.
Bit AFB toggles when the picture carrier is exactly at the desired IF frequency (= half the aligned IF-PLL frequency).
AFA is active in a window around this point.
For fast search-tuning applications this window can be increased by a factor 3 (AFW bit).
Tuner A.G.C.
The automatic gain control (A.G.C.) circuit operates on top sync level at negative modulated signals
or on peak white level at positive modulation, selected by MOD bit.
The tuner A.G.C. is controlled via pin 54.
The tuner A.G.C. take over point (T.O.P.) can be set over a wide range: 0.8 mVrms .. 80 mVrms
IF input signal amplitude.
The tuner AGC output may have to operate above Vcc of TDA8374.
Therefore pin 54 is an open collector output, that can operate from 0.3 up to Vcc+ 1 Volt
(at > 2 mA sink current)
PLL sound demodulator

The IF-video output at pin 6 (2Vpp) is fed through a sound bandpass filter and connected to the intercarrier sound IF
input pin 1.
An alignment free PLL tunes itself to the sound carrier and demodulates it.
The non volume-controlled front-end audio signal can be obtained from the deemphasis pin 55 (amplitude 300 mVeff).
Source select switch

TDA8374 input switch can select one of the following sources ;
pin 13 front-end : CVBS l int
pin17
: CVBS 2 ext
pin 11.pinlO : Y s-vhs, C s-vhs
Selected signal is available at the CVBS output pin 38, in case of Y/C input Y+C are added.
It drive teletext and the TDA8395 SECAM add-on.
For S-VHS applications, the Y,C input can be selected, independent of the CVBS source switch.
TDA8374 Y,C inputs are selected, while the source switch outputs CVBS l int or CVBS 2 ext on CVBS out.
Horizontal synchronization and protection

The synchronization separator adapts its slicing level in the middle between top-sync and black level of the CVBS signal.
The separated synchronization pulses are fed to the first phase detector and to the coincidence detector.
The -1 loop gain is determined by the components at pin 43 (C+RC).
The coincidence detector detects whether the horizontal line oscillator is synchronized to the incoming video.
The line oscillator is a VCO-type, running at twice the line frequency.
It is calibrated with the X-tal oscillator frequency of the colour decoder and has a maximum deviation of 2% of the
nominal frequency, so no alignment is-needed.
Calibration is done at start up( the TDA8374 must first know what colour X-tals are connected, bits XA and XB) and
after synchronization loss ( -1 coincidence detector Sync Locked bit SL).
The second phase detector -2 locks the phase of the horizontal driver pulses at output pin 40 to the horizontal
flyback pulse at input pin 41 .
31
This compensates for the storage time of the horizontal deflection transistor.
The - 2 loop filter (C) is externally connected to pin 42.
The horizontal phase can be given a static off set via I2C-but (HSH horizontal shift)
A dynamic correction is possible by current feedback into the - 2 loop filter capacitor.
To protect the horizontal deflection transistor, the ho rizontal drive is switched off immediately when a power
failure ( Power-On Reset bit POR ) is detected.
The power failure may have corrupted the contents of the internal data registers, so the TDA8374 should be
started up again.
The TDA8374 has a separate supply input (pin 37) that only used as a clean supply voltage for thehorizontal
oscillator circuits.
Vertical synchronization
The vertical sawtooth generator drives the vertical output.
It uses an external capacitor at pin 51 and a current reference resistor at pin 52.
The TDA8374 vertical drive has differential current outputs for DC-coupled vertical output stage, like the TDA8356 .
At TDA8356 input pins l and 2 this current is converted into a drive voltage via a resistor.
Geometry processing
With the TDA8374 is possible to implement automatic geometry alignment, because all parameters are adjusted
via the I2C bus.
The deflection processor of the TDA8374 offers the fo11owing five controls;
- Horizontal shift
- Vertical slope.
- Vertical amplitude
- Vertical S-correction
- vertical shift
Colour decoder
The colour decoder contains an alignment-free X-tal oscillator, a dual killer circuit and colour difference demodulators.
Together with the TDA8395 SECAM add-on a multi standard PAL/SECAM/NTSC decoder can be built with
automatic recognition.
Which standard can be decoded depends on the external Xtals used.
Two Xtal pins (34and 36) are present so normally no external switching is required.
The I.C. must be told which X-tals are connected (bits XA and XB).
This is important, because the X-tal frequency of the colour decoder is also used to calibrate many internal circuit.
The burst phase detector locks the Xtal oscillator with the chroma burst signal.
The phase detector operates during the burst key period only, to prevent disturbance of the PLL by the chroma signal.
Two gain modes provide:
- Good catching range when the PLL is not Locked.
- Low ripple voltage and good noise immunity once the PLL has locked
The killer circuit switches-off the R-Y and B-Y demodulators at very low input signal conditions (chroma burst amplitude).
A hysteresis prevents on/off switching at low, noisy signals.
Color standard
pin34
pin35
XA
XB
PAL4.43/SECAM + NTSC-4.43
none
4.43
PAL4.43/SECAM + NTSC-M
3.58
4.43
32
Integrated video filters

The TDA8374 has alignment-free internal luminance delay, chroma bandpass and chroma trap.
They are implemented as gyrator circuits tuned by tracking to the frequency of the chroma Xtal oscillator.
The chroma trap in the Y signal path is by-passed when Y/C input is selected (S-VHS ).
For SECAM an extra luminance delay is build-in, for correct delay of the luminance signal.
RGB output and black current stabilization

The colour difference signals (R-Y, B-Y) are matrixed with the luminance signal (Y) to obtain the RGBout output
signals (pins 21,20,29).
In the TDA8374 the matrix type automatically adapts to the decoded standard (NTSC,PAL) .
Linear amplifiers are used to interface external RGBrn signals (pins 24,25,26) from the SCART connector.
These signals overrule the internal RGB signals when the data insertion pin 26 (FBI) is switched to a level between
1.0V and 3.0V.
The contrast and brightness control and the peak white limiter operate on both internal and external RGB signals
R,G and B each have their own, independent gain control to compensate for the difference in phosphor efficiencies
of the picture tube: so called white point adjustment.
The nominal amplitude is about 2V black to white, at nominal input signals and control settings.
TDA8374 has a black current stabilization loop, that automatically adjust the black level to the cut-off voltage of the
picture tubes three gun cathodes.
Since no current is flowing when the voltage the cathode is equal to the cut-off voltage of the tube, the loop stabilizes
at a very small gun current.
This black current of the three guns is measured internally and compared with a reference current, to adjust the
black level of RGBout.
The black level 1oop is active during 4 lines at the end of the vertical blanking.
In the first line the leakage current is measured (max. acceptable 1l00 A).
In the next three lines the black levels of the three guns are adjusted.
The nominal value of the black current is 10 A.
The ratio of the black currents for the 3 guns tracks automatically with the white point adjustment, so the
back-ground colour is the same as the adjusted white point.
At switch-on of the TV receiver the black current stabilization circuit is not yet active and RGBout are blanked.
Before the first measurement pulses appear, O.5 sec delay ensures that the vertical deflection is active, so the pulses
will not be visible on the screen.
During the measuring lines RGBout will supply 4V pulses to the video output stages.
The TDA8374 waits until the black current feedback input (pin 18) exceeds 200 A, which indicates that the picture tube
is warm-up.
Then the black current stabilization circuit is active.
After a waiting time of about 1.0 sec, the blanking of RGBout is released.
Tuning
The AFC information of the TDA8374 is not available as an analogue voltage.
Automatic following (=frequency tracking, AFC) can be done via the I2C-bus by software.
The TDA8374 AFC window is typically 80 kHz wide.
This value is made higher than the 62.5 kHz tuning step, to prevent an automatic following loop from continuously
adapting the tuning frequency..
With this AFC window ( 40 kHz) the maximum tuning error is less than 62.5 kHz.
For high speed search-tuning-algorithms, the AFC window can be widened to 240 kHz via bit AFW.
33
TDA8395 SECAM decoder

The TDA8395 is an alignment-free SECAM colour decoder, including a Cloche filter, demodulator and line
identification circuit.
The Cloche filter is a gyrator-capacitor type.
Its frequency is calibrated in the vertical retrace period.
The calibration reference( pin 1 ) is obtained from the TDA8374 color X-tal oscillator (pin 33).
Pin 7 is a decoupling for the Cloche reference.
The voltage change at this pin due to leakage currents should be lower than 10 mV, during field scan, resulting in a
capacitor of minimal 100 nF.
Pin 8 is the reference capacitor for the PLL.
The voltage variation during field scan at this pin should be lower than 2 mV , resulting in a capacitor of 220 nF.
The sandcastle input (pin 15) is connected to TDA8374 pin 41 and is used for generation of the blanking periods and
provides clock information for the identification circuit.
The CVBS source select output (TDA8374 pin 38) supplies SECAM chroma to pin 16 of the TDA8395.
This is demodulated by a PLL demodulator, that uses the reference frequency at pin l and a bandgap reference to
obtain the desired demodulation characteristic.
If the digital line identification in theTDA8395 detects SECAM, pin 1 will sink a current of 150 (A out of TDA8374
SECAMref pin 33.
When the TDA8374 has not detected PAL or NTSC, it will respond by increasing the voltage at pin 33 from 1.5V to 5V.
Now the TDA8374 color difference outputs pin 30 and 29 are made high-ohmic and the TDA8395 output pin 9 and 10
are switched on.
These outputs will be disconnected and high-ohmic when no SECAM is detected for two frame periods, the decoder
will be initialized before trying again.
Base band delay line TDA4665

TDA4665 is an integrated double baseband delay line of 64 S.
It couples to the TDA8374 and TDA8395 without any switches or alignments.
The TDA4665 consist of two main blocks:
- Two delay lines of 64 sec in switched capacitor technique
- Internal clock generation of 3 MHz, line locked to the sandcastle pulse
The TDA4665 operates according to the mode demanded by the colour transmission standard:
- For PAL it operates as geometric adder to satisfy the PAL demodulation requirements
- In NTSC mode it reduces cross-colour interference (comb-filtering)
- For SECAM it repeats the colour difference signal on consecutive horizontal scan lines.
A sandcastle pulse is connected to pin 5.
The top pulse voltage (should not exceed 5 V) can be directly coupled to the 5 V sandcastle output of the TDA8374.
The R-Y and B-Y colour difference signals (from TDA8374 pins 30 and 29) are AC-coupled and clamped by the
input stages at pins 16 and 14.
An internal 6 MHz Current controlled oscillator is line locked via a PLL to the sandcastle pulse at pin 5.
This clock drives the delay lines to obtain the required 64 sec.
Sample and hold low pass filters supress the clock signal.
The original and the delayed signals are added, buffered and fed to the output pins 11 and 12.
These are AC-coupled to the R-Y and B-Y colour difference input pin 32 and 31 of TDA8374.
The TDA4665 needs a 5 V supply voltage on pin l for the digital part and on pin 9 for the analog part.
34
TDA8356 vertical deflection.

The TDA8356 is a vertical deflection circuit.
It can be used in 90 deflection systems with frame frequencies from 50 up to 120 Hz
With its bridge configuration the deflection output can be DC coupled with few external components.
Only a supply voltage for the scan and a second supply for the flyback are needed.
The TDA8356 can drive max.2A.
The vertical drive currents of TDA8374 pins 47 and 46 are connected to input pins l and 2 of the TDA8356.
The currents are converted into a voltage by a resistor between pins 1 and 2.
Pin2 is on a fixed DC level (internal bias voltage) and on pin l the drive voltage can be measured (typical 1.8 Vpp).
The drive voltage is amplified by A and fed to two amplifiers B and C, one is inverting and the other is a non
inverting amplifier.
The outputs (pins 4 and 7) are connected to the series connection of the vertical deflection coil and feedback resistor .
The voltage across feed back resistor is fed via pin 9 to correction amplifier D, to obtain a deflection current which is
proportional to the drive voltage.
The supply voltage for the TDA8356 is 16V at pin 3.
The flyback generator has a separate supply voltage of 45V on pin 6.
The guard pulse is useful to synchronize OSD.
Horizontal deflection
The circuit contains horizontal drive, line output transformer.
The horizontal driver pulses from the TDA8374 are amplified in the horizontal drive circuit, to get sufficient base-drive
current for the high voltage switching transistor Q401.
During the horizontal scan period( =52 s) Q401 will conduct, and a sawtooth current flows from +110/123V through the
primary winding of the FBT to ground.
After this time Q401 is switched off and the energy stored in the FBT during the scan period will be transformed to the
flyback capacitor C410.
This energy transfer will take place in a cosine shape because the primary of the FBT and C410 from a resonant circuit.
The time the energy is transferred from FBT to C410 and back to the FBT, is called the flyback time and will take place
in about 12 s.
The flyback peak voltage is about 8 times the scan voltage.
In series with the horizontal deflection coil there is a (damped) linearity corrector coi1.
During the scan there is some loss in the resistance of the deflection coi1.
In the first part of a line the linearity corrector stores some energy in a permanent magnet until it is saturated.
This improves the linearity of the horizontal scan speed.
The required S correction for the picture tube can be adjusted with the value of C411.
The beam current limiting information (BeamCurr) is derived from the foot of the H.V winding of the FBT.
This is connected via resistor to +8V.
As the beam current increase, the voltage on line BeamCurr decreases.
BeamCurr is damped by a integration filter before it is fed back to TDA8374 pin 22.
The TDA8374 will decrease the contrast (and eventually the brightness) to limit the average beam current.
35
Video amplifiers
Three TDA6106Q integrated video amplifiers drive cathode of the picture tube directly.
They are protected against CRT flashover discharges and ESD (electro static discharge).
The three video amplifiers, have a beam current output I black, used by the TDA8374 black current loop to control
the black level on the cathodes.
The outputs can be connected together because the black current 1oop sequentially controls the black level for each
cathode.
The amplification of the TDA6106Q is set by the resistors between pin 3 and 9 and between pin 3 (negative-input) and
the TDA8374 output.
There are no alignment any more on the CPT panel, because of the automatic black current stabilization and because
the white point adjustment can be done in the TDA8374 via I2C bus.
Power Supply STR-S5707

(1) VIN terminal, start-up circuit
A start-up circuit is to start and stop a operation of a control IC by detecting a voltage appearing at a VIN terminal
(pin-9).
At start up of a power supply, when a voltage at the VIN terminal reaches to 8V (typical) by charging up C807 by
the function of a start-up resistor, R803, a control circuit starts operating by the function of the start-up circuit.
After the control circuit starts its operation, power source is obtained by smoothing voltage appearing at winding of
pin6-7 of T801.
(2) Oscillator, F/B terminal voltage (Pin 7)
A oscillator generates pulse signals which turns a power transistor on and off by making use of charge and discharge
of C1 and C2 incorporated in the Hybrid IC.
Constant voltage control of a switch-mode power supply is performed by changing both ON-time and OFF-time except
when the load is light (ex. remote control stand-by mode of TVs).
The ON-time is controlled by changing a current charged by C1, which is as the result of that the detection winding of
pin5-7 of T801, which detects a change of voltage in a secondary side, connected to the sensing terminal (Pin 7) has the
current in accordance with an output signal from an output voltage detection circuit (an error amplifier) built in.
As an AC input voltage to the power supply gets the higher and a load current the smaller, the current flowing to the
SENS terminal gets the larger, and the ON-time gets the shorter.
(3) Function of INH terminal (Pin 6), control of OFF-time
Signal to the INH terminal is used as inputs to COMP.1 and COMP.2 inside of the control IC.
A threshold voltage of COMP.1, VTH1 is set at 0.75V (Ta=25) and an input signal to a drive circuit becomes almost
0V (the power transistor is in OFF mode) when a voltage at the INH terminal reaches the VTH1.
A threshold voltage of COMP.2, VTH2, is set at 1.5V (Ta=25).
When the INH terminal voltage reaches VTH2, an output from COMP.2 reverses (the power transistor is in on mode).
Quasi-resonant operation
By inputting the voltage of winding of pin6-7 of T801 which is synchronized with the energy discharge time of a
secondary winding, pin14(or 15)-16 of T801, to the INH terminal through D805 and R809, quasi-resonant operation
can be achieved.
When the power transistor turns off and a voltage higher than VTH2 is applied to the INH terminal, C3 immediately
discharges and then starts charging again.
Even after the discharge of energy of a secondary winding is completed, VINH does not immediately increases.
When it gets lower than VTH1, the transistor turns on.
36
Stand-By Mode
While being in remote control stand-by mode, the output voltage is kept on providing to the secondary side and
the power transistor operates at A class mode.
By connecting INH terminal (Pin 6) to the GND, the OFF-time of the power transistor is fixed at set time
( T OFF = 50usec at Ta = 25 ) of the built-in oscillator, and only ON-time changes depending on input and output
conditions of the power supply.
Therefore, it enables to hold an oscillation frequency in light mode below 20KHz (typical).
(4) Drive circuit
The STR-S5707 applies the proportional drive system in order to minimize turn-on and saturation loss, and storage time.
(5) OCP (over-current protection) function
Over-current protection is performed pulse by pulse by directly detecting collector current of the power transistor.
Detecting voltage is set to -1V below a reference point of GND (ground).
(6) Latch circuit
It is a circuit which sustains an output from the oscillator low and stops operation of the power supply when over-voltage
protection (OVP) circuit and thermal shutdown (TSD) circuit are in operation.
As the sustaining current of the latch circuit is 500 A maximum when VIN terminal voltage is 4V, the power supply
circuit sustains the off state as long as current of 500 A minimum flows to VIN terminal from a start-up resistor.
In order to prevent a malfunction to be caused by a noise and so on, delay time is provided by C1 incorporated in the
IC and, therefore, the latch circuit operates when the OVP or TSD circuit is in operation, or an external signal input is
provided for about 10 sec or longer.
In addition, even after the latch circuit start operating, the constant voltage regulator (Reg) circuit is in operation and the
circuit current is at high level.
As a result, VIN terminal voltage rapidly decreases.
When VIN terminal voltage becomes lower than the shutdown voltage, VIN(OFF) (4.9V typical), it starts increasing as the
circuit current is below 500 A.
When it reaches the ON-state voltage, VIN (ON) (8V typical), VIN terminal voltage starts decreasing because the circuit
current increases again.
When the latch circuit is on, VIN terminal voltage increases and decreases within the range from 4.9V typical to
8V typical and is prevented from abnormally rising.
Cancellation of the latch is done by decreasing VIN terminal voltage below 3.3V.
The power supply can be restarted after disconnecting an AC input to the power supply once.
(7) Thermal shutdown circuit
It is a circuit to trigger the latch circuit when the frame temperature of the IC exceeds 150 (typical).
Although the temperature is actually sensed at the control chip, it works against overheating of the power transistor
as the power transistor and the control IC are mounted on the same lead frame.
(8) Over-voltage protection circuit
It is a circuit to trigger the latch circuit when VIN terminal voltage exceeds 11V (typical).
Although it basically functions as protection of VIN terminal against over-voltage, since VIN terminal is usually supplied
from the drive winding of the transformer and the voltage is proportional to the output voltage, it also functions against
the over-voltage of secondary output which causes when the control circuit opens or in some other events.
37
Trouble Shooting Charts

1. NO RASTER
CHECK MAIN B+(+123V/+110V) LINE
ABNORMAL
NORMAL
CHECK VOLTAGE AT
(+) OF C807(220F 400V)
310Vdc AT AC 220V
CHECK HEATER VOLTAGE,

VIDEO B+(200V) LINE,
16.5V & 48V LINE
NORMAL
ABNORMAL
ABNORMAL
CHECK / REPLACE F801
FUSE(T4A 250V)
CHECK / REPLACE
D801~D804(1S1888X4)
R803(10W 3.3OHM)
CHECK / REPLACE
I801(STR-S5707)
& PERIPHERAL
COMPONENT
NORMAL
CHECK HORIZONTAL
DRIVE PULSE AT PIN 40
OF I501(TDA8374A)
[REFER TO WAVE
FORM ]
ABNORMAL
CHECK /REPLACE
I804(PC817)
D812(BYW 95C)
R814(2W 56K)
NORMAL
CHECK HORIZONTAL
Vcc(+8V DC) AT
PIN 37 OF I501
CHECK / REPLACE
R410(1/4W 3.9)
1401 (2SD1207)
T401 (TD-10A2)
Q402 (2SD2499)
ABNORMAL
CHECK POWER SWITCHING

VOLTAGE AT PIN 43 OF I701
*POWER ON; HIGH
*STAND-BY ; LOW
CHECK SDA(PIN 8)
& SCL(PIN7)
WAVEFORM OF I501
CHECK / REPLACE
I802(TDA8138)
I803(KA7808)
OK
ABNORMAL
NORMAL
ABNORMAL
CHECK VOLTAGE(+5V DC)

AT PIN 11 & PIN 37 OF I701
NORMAL ABNORMAL
CHECK / REPLACE
I501(TDA8374A)
CHECK / REPLACE
D813 (BYV95C)
D814 (BYV95C)
R824
(2W 43)
Q802 (KTC 3198Y)
Q803 (KTC 3198Y)
T801 (TSM-4245A)
CHECK SDA(PIN 3)
& SCL(PIN4)
WAVEFORM OF I701
OK
NORMAL
CHECK / REPLACE
X701(20MHz, 18MHz)
CHECK / REPLACE I701
40
CHECK / REPLACE
T402 F.B.T
& CRT
2. NO PICTURE(RASTER OK)
CHECK VIDEO SIGNAL

AT PIN 13 OF I501(TDA8374A)
[REFER TO WAVEFORM ]
ABNORMAL
NORMAL
CHANGE INPUT MODE

RF AV RF
CHECK WAVEFORM AT
PIN 29, PIN 30 OF I501
CHECK / REPLACE
I701
& PERIPHERAL
COMPONENT
ABNORMAL
ABNORMAL
NORMAL
CHECK WAVEFORM
AT PIN 31, PIN 32
OF I501
CHECK PICTURE CONDITION

NORMAL NORMAL
FAVOURITE
CHECK /
REPLACE
Q702, Q703
ABNORMAL
CHECK TUNING VOLTAGE

AT VT OF TUNER
CHECK /
REPLACE
R759,R720
I703
OK
CHECK WAVEFORM
AT PIN 19, 20, 21
OF I501
CHECK / REPLACE
I501
ABNORMAL
CHECK / REPLACE
I502(TDA4665)
I503(TDA8395)
ABNORMAL
CHECK 33V LINE
ABNORMAL
NORMAL
NORMAL
CHECK VIDEO SIGNAL
AT CATHOD OF CRT
[REFER TO WAVEFORM
]
CHECK BAND SELECT

VOLTAGE AT BL,BH,BU
& B+ VOLTAGE
OF TUNER
ABNORMAL
CHECK / REPLACE
AT PIN 40, 41, 42
OF I701
ABNORMAL
NORMAL
CHECK / REPLACE
I901, I902, I903
OK
(CRT BOARD)
CHECK / REPLACE TUNER
CHECK / REPLACE
OK Q705,Q706,Q707
Q708,Q709,Q710
CHECK / REPLACE
I501
41
NORMAL
ABNORMAL
CHECK SIGNAL
AT PIN 18
OF I501
ABNORMAL
CHECK / REPLACE
CRT
CHECK VOLTAGE
VIDEO B+,
HEATER
OK
CHECK
HORIZONTAL
CIRCUIT PARTS
NORMAL
NORMAL
CHECK / REPLACE
Q101, Q102, SF101
NORMAL
ABNORMAL
ABNORMAL
3. NO VERTICAL SCANING(ONE HORIZONTAL LINE ON SCREEN)
CHECK / REPLACE
P401 & DY ]
CHECK VERTICAL Vcc

+16.5V AT PIN3
& +48V AT PIN6
OF I301(TDA 8356)
NORMAL
ABNORMAL
CHECK SIGNAL
AT PIN1 & PIN2
OF I301 [REFER TO
]
WAVEFORM
CHECK / REPLACE
D401(BYV95C)
D409(BYV95C)
R303(1W 15K)
ABNORMAL
NORMAL
CHECK / REPLACE
CRT
CHECK OUTPUT
WAVEFORM AT PIN46,
PIN47 OF I501
CHECK SIGNAL
AT PIN7 OF I301
NORMAL
NORMAL
ABNORMAL
CHECK / REPLACE
R304, R305
C304, R307
CHECK / REPLACE
I301
OK
42
ABNORMAL
CHECK / REPLACE
I501
4. NO COLOR
CHECK VIDEO SIGNAL
AT PIN13 OF I501(TDA8374A)
ABNORMAL
NORMAL
CHECK SYSTEM MODE
AUTO PAL SECAM
N3 N4 N5
CHECK SIGNAL
AT PIN29, PIN30
OF I501
ABNORMAL
NORMAL
CHECK / REPLACE
X501(4.43MHz X-TAL)
X502(3.58MHz x-tal)
CHECK SIGNAL
AT PIN31, PIN32
OF I501
ABNORMAL
NORMAL
CHECK SIGNAL
AT PIN19, 20, 21
OF I501
CHECK / REPLACE
I502 & I503
ABNORMAL
NORMAL
CHECK VIDEO SIGNAL
AT CATHOD OF CRT
[REFER TO
]
WAVEFORM
CHECK / REPLACE
I501
ABNORMAL
NORMAL
CHECK / REPLACE
CRT
CHECK / REPLACE
I901, I902, I903
(CRT BOARD)
OK
43
REFER TO
NO PICTURE CHART
5. NO SOUND(PICTURE OK)
CHECK AUDIO SIGNAL
AT PIN15 OF I501
ABNORMAL
CHECK MUTE VOLTAGE
AT PIN20 OF I701
*MUTE : HIGH
ABNORMAL
NORMAL
CHECK SIF SIGNAL
AT PIN1 OF I501
CHECK /REPLACE
R619, C602, Q604
D605, Q606, I701
ABNORMAL
NORMAL
CHECK SIGNAL WAVEFORM

AT PIN6 OF I501
NORMAL
NORMAL
CHECK AUDIO SIGNAL

AT PIN3(TDA7056)
[AT PIN 1&9(TDA1519B)]
ABNORMAL
CHECK / REPLACE
D813, C821
CHECK / REPLACE
Q501, R602, R603
Q605 & PERI. COMP
NORMAL
OK
CHECK VOLTAGE Vcc(+15Vdc)

AT PIN2(TDA7056)
[AT PIN7(TDA1519B)]
NG
CHECK POWER
PART CIRCUITS
CHECK AUDIO OUTPUT SIGNAL

AT PIN6 & 8(TDA7056)
[AT PIN4 & 6(TDA1519B)
ABNORMAL
NORMAL
CHECK / REPLACE
SP01(TDA7056)
[SP01 & SP02(TDA1519B)]
CHECK / REPLACE
I601(TDA7056)
[I601(TDA1519B]
OK
44
ABNORMAL
CHECK / REPLACE
TUNER, SAW FILTER
Q101, Q102 & PERI. COMP
6. NO EXTERNAL A/V(RF OK)

CHECK EXTERNA AUDIO
& VIDEO SIGNAL
AT PIN2 & 17 OF I501
RESPECTIVELY
ABNORMAL
NORMAL
OK
CHECK RCA JACK
CHECK WAVEFORM
AT PIN7 & 8 OF I501
ABNORMAL
OK
OK
7. NO ON-SCREEN DISPLAY(PICTURE OK)

CHECK HORI. & VER. SYNC
AT PIN46 & 45
OF I701 RESPECTIVELY
NORMAL
ABNORMAL
CHECK / REPLACE
Q301, Q302(VER. SYNC)
D401, R414(HORI. SYNC)
OK
ABNORMAL
NORMAL
CHECK WAVEFORM
AT PIN23, 24, 25, 26
OF I501
ABNORMAL
CHECK / REPLACE
PERI. COMP
CHECK OSD R/G/B SIGNAL

& BLANKING SIGNAL
AT PIN 47, 48, 49 & 50 OF I701
CHECK OSD IN/PUT WAVEFORM

AT PIN 38, 39 OF I701
NORMAL
OK
CHECK / REPLACE
I501
CHECK / REPLACE
I701 & PERI. COMP
OK
45
8. REMOTE CONTROL UNIT TROUBLE(LOCAL CONTROL OK)
CHECK PULSE AT COLLECTOR

OF Q1(TRANSMITTER BOARD)
ABNORMAL
CHECK / REPLACE
Q1 / LED1
(TRANSMITTER BOARD)
CHECK PULSE
AT PIN36 OF I701
NG
CHECK IC1
(DHR-001S)
OK
NG
CHECK / REPLACE
X1, C1
ABNORMAL
OK
CHECK / REPLACE
I704(TFMU5380)
NORMAL
CHECK / REPLACE
I701 & PERI. COMP
OK
46
IC DC Voltage Charts
Input signal
- Video : color BAR(PM5518)-PAL
-Audio : 1khz sine wave
Users control condition
- Contrast, Brightness, Color, Volume(Normal condition)
Line Voltage
- AC 220V, 50HZ
All the Voltage in each point are measured with multimeter
I701(-com)
PIN NO
10
11
12
13
14
15
V(DC)
4.7
4.5
4.5
4.7
0
(option)
4.4
2.0
2.2
4.7
PIN NO
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
V(DC)
4.0
4.4
0
MUTE 4.2
0
0
0
(TEXT option)
PIN NO
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
V(DC)
4.6
4.7
4.6
4.6
3.7
3.7
4.4
4.4
2.9
PIN NO
46
47
48
49
50
51
52
V(DC)
0.2
47
I501(TDA8374A)
PIN NO
10
11
12
13
14
V(DC)
3.8
3.6
3.6
2.8
3.0
4.6
4.6
6.64
3.4
8.0
100mv
PIN NO
15
16
17
18
19
20
21
22
23
24
25
26
27
28
V(DC)
3.76
3.7
3.5
5.3
2.5
3.8
2.7
3.1
3.4
3.4
3.4
2.5
2.5
PIN NO
29
30
31
32
33
34
35
36
37
38
39
40
41
42
V(DC)
1.7
1.7
4.0
4.0
1.6
2.6
2.6
4.6
8.0
3.4
6.0
3.0
4.8
PIN NO
43
44
45
46
47
48
49
50
51
52
53
54
55
56
V(DC)
4.0
8.0
2.3
2.3
4.2
4.2
3.9
4.0
3.7
3.4
3.2
4.7
I301(TDA8356)
PIN NO
V(DC)
2.3
2.3
16.8
8.0
44
8.1
8.1
I502(TDA4665)
PIN NO
10
11
12
13
14
15
16
V(DC)
5.0
1.0
5.0
2.9
2.9
1.4
0.7
114
I503(TDA8395)
PIN NO
10
11
12
13
14
15
16
V(DC)
1.6
1.2
7.9
3.3
4.2
1.7
1.7
0.7
2.8
I802(TDA8138)
PIN NO
V(DC)
13.0
14.0
3.0
4.82
5.05
11.98 5.05
48
Electrical Parts List

LOC.
PART-CODE
PART-NAME
PART TYPE
ZZ100
48B3228B04
TRANSMITTER REMOCON
R-28B04
ZZ110
PTACPWA499
ACCESSORY AS
DTC-14Q1VM
M821
4858211400
POLY BAG
P.E FILM T0.03X600X550
30
47P7500001
BATTERY
AAM 1.5V
10000
48586A1617
MANUAL INSTRUCTION
ALL
ZZ120
PTBCSHA499
COVER BACK AS
DTC-14Q1VM
M211
4852147200
COVER BACK
HIPS BK
M541
4855415800
SPEC PLATE
150ART P/E FILM (C/TV)
M781
4857817611
CLOTH BLACK
FELT T0.7 L=200
ZZ130
PTPKCPA499
PACKING AS
DTC-14Q1VM
10
6520010100
STAPLE PIN
18M/M J D O
20
6520010200
STAPLE PIN
#3417
M801
485803871D
BOX CARTON
SW-2
M811
4858179200
PAD
EPS 14Q1
M821
4858210702
BAG P.E
L.D.P.E T0.03X1150X1000
M822
4858211400
POLY BAG
P.E FILM T0.03X600X550
40
2TF01612CL
TAPE FILAMENT
12MMX55ME CLEAR
ZZ131
58G0000084
COIL DEGAUSSING
DC-1450
ZZ132
48519A4610
CRT GROUND AS
1401H-1015-1P
ZZ140
PTCACAA499
CABINET AS
DTC-14Q1VM
M191
4851924401
BUTTON CTRL AS
4933001+5530400
M201A
4856013300
SCREW CRT FIXING AS
30X80 BK
M201B
4856214900
WASHER RUBBER
TMR-CA
M201C
4856013301
SCREW CRT FIXING AS
30X140 YL
M211A
7122401412
SCREW TAPPING
T2S TRS 4X14 MFZN BK
M211C
7128301212
SCREW TAPPING
T2S WAS 3X12 MFZN BK
M211D
7122401412
SCREW TAPPING
T2S TRS 4X14 MFZN BK
M481
4854848200
BUTTON POWER
ABS BK
M481A
4856716000
SPRING
SWPA PIE0.5
M561
4855613600
MARK BRAND
COPPER T0.4
SP01A
7128301011
SCREW TAPPING
T2S WAS 3X10 MFZN
V901
PTRTPWA001
CRT AS
PAL 14 ITC CRT AS
V01
58D1000046
COIL DY
ODY-M1401
V02
48A96R004-
RUBBER WEDGE
HMR 28 SR (|0X54)
V03
4850PM001-
MAGNET CP
NY-225 (MINI NECK)
V04
2TG00025
TAPE GLASS
W25
V05
2224050033
BOND SILICON
RTV 252
V901
48A96414P1
CRT BARE
A34JLL90X
48A96414P2
CRT BARE
A34JLL91X
48A96414P3
CRT BARE
A34JLL92X
ZZ200
PTFMSJA499
MASK FRONT AS
DTC-14Q1VM
M201
4852060500
MASK FRONT
HIPS BK
M351
4853533201
HOLDER BRKT
HIPS BK
49
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
ZZ220
PTSPPWA499
SPEAKER AS
DTC-14Q1VM
PA601
4850703S03
CONN AS
YH025-03+YST025+ULW=200
SP01
4858306810
SPEAKER
3W 16 OHM F2035C03-3
ZZ290
PTMPMSA499
PCB MAIN MANUAL AS
DTC-14Q1VM
10
2193102005
SOLDER BAR
SN:PB=63:47 S63S-1320
20
2193011101
SOLDER WIRE
RS 60-1.2 1.6A
30
2291050615
FLUX SOLDER
DF-2012U
40
2291050301
FLUX SOLVENT
IM-1000
50
2291140501
WAX COVER
C410
CMYH3C692J
C MYLAR
C411
CMYE2D334J
C MYLAR
200V PU 0.33MF J
C416
CCYR3A102K
C CERA
HIKR 1KV 1000PF K 125C
C801
CL1UC3104M
C LINE ACROSS
WORLD AC250V 0.1UF M R.47
C806
CEYA2G221G
C ELECTRO
400V LSS 220MF (30X40)
C814
CCYR3D102K
C CERA
2KV R 1000PF K 125C
C832
CH1BFE472M
C CERA AC
AC400V 4700PF M U/C/V
C911
CCYB3D472K
C CERA
2KV B 4700PF K
D103
D1S2186-
DIODE
1S2186
D601
D1S2186-
DIODE
1S2186
D706
DKLR114L
LED
KLR114L
D812
DBYW95C-
DIODE
BYW95C (TAPPING)
F801
5FSGB4022L
FUSE GLASS TUBE
SEMKO TL 4A 250V MF51
I301
1TDA8356
IC VERTICAL
TDA8356
I301A
4857024617
HEAT SINK
AL EX
I301B
7174301011
SCREW TAPPTITE
TT2 RND 3X10 MFZN
I501
1TDA8374A-
IC VCD
TDA8374A
I502
1TDA4665V4
IC DELAY
TDA4665/V4
I503
1TDA8395
IC
TDA8395
I601
1TDA7056
IC
TDA7056
I601A
4857025400
HEAT SINK
A1050P-H24 T2.0
I601B
7174300811
SCREW TAPPTITE
TT2 RND 3X8 MFZN
I701
1DW370ASM1
IC MICOM
DW370ASM1
I702
124LC08B
IC MEMORY
24LC08B
I703
1UPC574J
IC
UPC574J
I704
1TFMW5380-
IC PREAMP
TFMW5380
I801
1STRS5707-
IC POWER
STR-S5707
I801A
4857026107
HEAT SINK
AL EX
I801B
7174301011
SCREW TAPPTITE
TT2 RND 3X10 MFZN
I802
1TDA8138
IC REGULATOR
TDA8138
I802A
4857025401
HEAT SINK
A1050P-H24 T2
I802B
7174300811
SCREW TAPPTITE
TT2 RND 3X8 MFZN
I803
1KA7808-
IC REGULATOR
KA7808
I804
1LTV817C
IC PHOTO COUPLER
LTV-817C
1.6KV BUP 6900PF J
50
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
I901
1TDA6106Q-
IC AMP
TDA6106Q
I902
1TDA6106Q-
IC AMP
TDA6106Q
I903
1TDA6106Q-
IC AMP
TDA6106Q
JA01
WP-1BK1715
WIRE LEAD 1007
AWG22 1/0.65 BK 5-170-5
JA02
WP-1BK1715
WIRE LEAD 1007
AWG22 1/0.65 BK 5-170-5
JV03
4859104250
JACK PIN BOARD
YSC-0406(YW+YW+RD+RD)
L102
58C9780027
COIL CHOKE
TRF-1201B (0.97 UH)
L405
58H0000016
COIL H-LINEARITY
L-102 (102UH)
L603
58C9430599
COIL CHOKE
AZ-9004Y(94MH)
L801
5PLF20A1
FILTER LINE
LF-20A1
L803
58C9430599
COIL CHOKE
AZ-9004Y(94MH)
M352
97P2316600
HOLDER AC CORD
NYLON66 UL/CSA
M353
4853530901
HOLDER LED
HIPS BK
M681
4856812001
TIE CABLE
NYLON66 DA100
M791
4857913302
RUBBER CUSHION
FR RUBBER SPONGE
PA501
4850706S02
CONN AS
YH025-06+YST025+ULW=400
PA502
4850704S04
CONN AS
YH025-04+YST025+ULW=400
PWC1
4859902910
CORD POWER AS
KKP419C+BL102NG+TUBE=2100
A000
4859901111
CORD POWER
KKP-419C KLCE-2F (2.1ME)
P401
4859240020
CONN WAFER
YFW500-05
P801
4859242220
CONN WAFER
YFW800-02
P802
4859242220
CONN WAFER
YFW800-02
P904
4859275220
CONN WAFER
YF254-05R (ANGLE)
P905
4859262120
CONN WAFER
YFW800-01
Q402
T2SD2499
TR
2SD2499
Q402A
4857027200
HEAT SINK
AL T1.0
Q402B
7174301011
SCREW TAPPTITE
TT2 RND 3X10 MFZN
R801
DEC140M290
POSISTOR
ECPCC140M290
R803
RX10B339JN
R CEMENT
10W 3.3 OHM J BENCH 4P
SCT1
4859303030
SOCKET CRT
ISMM03S
SF101
5PK6259K
FILTER SAW
K6259K
SW01
5S50101008
SW TACT
KPT-1105V 1C-1P
SW02
5S50101008
SW TACT
KPT-1105V 1C-1P
SW03
5S50101008
SW TACT
KPT-1105V 1C-1P
SW04
5S50101008
SW TACT
KPT-1105V 1C-1P
SW05
5S50101008
SW TACT
KPT-1105V 1C-1P
SW801
5S40101143
SW PUSH
PS3-22SP (P.C.B)
TU01
4859709230
TUNER VARACTOR
VTSS7SZ3
TU01A
4859101820
JACK ANT
JACK-D1
T401
50D10A2-
TRANS DRIVE
TD-10A2
T402
50H0000177
FBT
HST1142.5057
T801
50M4242A5-
TRANS SMPS
TSM-4242A5
X701
5XE20R000E
CRYSTAL QUARTZ
HC-49/U 20.000MHZ 30PPM

51
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
Z503
5PTPS60MB-
FILTER CERA
TPS 6.0MB(EFC-S6ROME3)
Z504
5PTPS65MB-
FILTER CERA
TPS 6.5MB(EFC-S6R5ME3)
ZZ200
PTMPJ0A499
PCB MAIN (RHU) AS
DTC-14Q1VM
C308
CEXF1E471C
C ELECTRO
25V RUS 470MF (10X16) TP
C412
CEXF2C339V
C ELECTRO
160V RSS 3.3MF (8X16) TP
C417
CEXF2E330V
C ELECTRO
250V RSS 33MF (13X25) TP
C427
CCXB3D471K
C CERA
2KV B 470PF K (TAPPING)
C428
CEXF2C470V
C ELECTRO
160V RSS 47MF (13X25) TP
C615
CEXF1V331C
C ELECTRO
35V RUS 330MF (10X20) TP
C809
CEXF1E331V
C ELECTRO
25V RSS 330MF (10X12.5)TP
C818
CEXF2C101V
C ELECTRO
160V RSS 100MF (16X25) TP
C819
CEXF2C101V
C ELECTRO
160V RSS 100MF (16X25) TP
C821
CEXF1V102V
C ELECTRO
35V RSS 1000MF (13X25) TP
C823
CEXF1E222C
C ELECTRO
25V RUS 2200MF (16X25) TP
ZZ200
PTMPJBA499
PCB MAIN M-10 AS
DTC-14Q1VM
L104
58E0000S37
COIL AFT
TRF-A001
P101
485923162S
CONN WAFER
YW025-03 (STICK)
P102
485923162S
CONN WAFER
YW025-03 (STICK)
P501
485923192S
CONN WAFER
YW025-06 (STICK)
P502
485923172S
CONN WAFER
YW025-04 (STICK)
P601
485923162S
CONN WAFER
YW025-03 (STICK)
R303
RS01Z153J-
R M-OXIDE FILM
1W 15K OHM J (TAPPING)
R307
RS02Z271J-
R M-OXIDE FILM
2W 270 OHM J (TAPPING)
R408
RS02Z561J-
R M-OXIDE FILM
R409
RS01Z103J-
R M-OXIDE FILM
R415
RF01Z129J-
R FUSIBLE
1W 1.2 OHM J (TAPPING)
R720
RS02Z562JS
R M-OXIDE FILM
2W 5.6K OHM J SMALL
R759
RS02Z562JS
R M-OXIDE FILM
2W 5.6K OHM J SMALL
R805
RS02Z363J-
R M-OXIDE FILM
R811
RS01Z240J-
R M-OXIDE FILM
R812
RF02Z338J-
R FUSIBLE
2W 0.33 OHM J (TAPPING)
R814
RS02Z563J-
R M-OXIDE FILM
R824
RS02Z430JS
R M-OXIDE FILM
2W 43 OHM J SMALL
R825
RS02Z330J-
R M-OXIDE FILM
ZZ200
PTMPJRA499
PCB MAIN RADIAL AS
DTC-14Q1VM
CA04
CEXF1H479V
C ELECTRO
50V RSS 4.7MF (5X11) TP
CA05
CEXF1H100V
C ELECTRO
50V RSS 10MF (5X11) TP
C103
CEXF1E470V
C ELECTRO
C104
CEXF1H479V
C ELECTRO
50V RSS 4.7MF (5X11) TP
C105
CEXF1H479V
C ELECTRO
50V RSS 4.7MF (5X11) TP
C107
CEXF1H479V
C ELECTRO
50V RSS 4.7MF (5X11) TP
C109
CEXF1H100V
C ELECTRO
C111
CMXM2A104J
C MYLAR
100V 0.1MF J (TP)

52
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
C115
CEXF1H229V
C ELECTRO
50V RSS 2.2MF (5X11) TP
C116
CMXM2A223J
C MYLAR
100V 0.022MF J TP
C117
CMXM2A473J
C MYLAR
100V 0.047MF J (TP)
C119
CMXM2A473J
C MYLAR
100V 0.047MF J (TP)
C301
CMXB1H104J
C MYLAR
50V EU 0.1MF J (TP)
C304
CMXB1H104J
C MYLAR
50V EU 0.1MF J (TP)
C305
CMXM2A103J
C MYLAR
100V 0.01MF J (TP)
C306
CBXF1H104Z
C CERA SEMI
50V F 0.1MF Z (TAPPING)
C311
CMXM2A104J
C MYLAR
100V 0.1MF J (TP)
C402
CEXF1H109V
C ELECTRO
C406
CCXB2H222K
C CERA
500V B 2200PF K (TAPPING)
C413
CEXF1H100V
C ELECTRO
C414
CCXB2H471K
C CERA
C415
CMXM2A104J
C MYLAR
100V 0.1MF J (TP)
C418
CMXM2A223J
C MYLAR
100V 0.022MF J TP
C419
CEXF1E101V
C ELECTRO
25V RSS 100MF (6.3X11) TP
C420
CXSL2H470J
C CERA
500V SL 47PF J (TAPPING)
C423
CCXB2H102K
C CERA
C502
CEXF1H229V
C ELECTRO
50V RSS 2.2MF (5X11) TP
C503
CMXM2A223J
C MYLAR
100V 0.022MF J TP
C504
CMXM2A223J
C MYLAR
100V 0.022MF J TP
C505
CEXF1E101V
C ELECTRO
25V RSS 100MF (6.3X11) TP
C506
CMXM2A473J
C MYLAR
100V 0.047MF J (TP)
C508
CMXM2A473J
C MYLAR
100V 0.047MF J (TP)
C509
CEXF1H478V
C ELECTRO
50V RSS 0.47MF (5X11) TP
C510
CMXM2A473J
C MYLAR
100V 0.047MF J (TP)
C512
CEXF1H109V
C ELECTRO
C525
CEXF1E470V
C ELECTRO
C526
CMXM2A104J
C MYLAR
100V 0.1MF J (TP)
C527
CMXL1J224J
C MYLAR
63V MEU 0.22MF J (TP)
C529
CEXF1E470V
C ELECTRO
C530
CEXF1H109V
C ELECTRO
C531
CMXM2A104J
C MYLAR
100V 0.1MF J (TP)
C532
CMXM2A104J
C MYLAR
100V 0.1MF J (TP)
C533
CMXM2A104J
C MYLAR
100V 0.1MF J (TP)
C534
CEXF1E101V
C ELECTRO
25V RSS 100MF (6.3X11) TP
C602
CEXF1E330V
C ELECTRO
C607
CEXD1E100F
C ELECTRO
25V RND 10MF (5X11) TP
C610
CEXF1H229V
C ELECTRO
50V RSS 2.2MF (5X11) TP
C611
CEXF1H100V
C ELECTRO
C614
CMXM2A223J
C MYLAR
100V 0.022MF J TP
C617
CEXF1E221V
C ELECTRO
25V RSS 220MF (8X11.5) TP
C622
CEXF1H100V
C ELECTRO

53
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
C702
CEXF1E470V
C ELECTRO
C706
CEXF1H100V
C ELECTRO
C707
CEXF1E101V
C ELECTRO
25V RSS 100MF (6.3X11) TP
C710
CMXM2A104J
C MYLAR
100V 0.1MF J (TP)
C711
CMXM2A104J
C MYLAR
100V 0.1MF J (TP)
C712
CEXF1H470V
C ELECTRO
50V RSS 47MF (6.3X11) TP
C713
CCXF1H103Z
C CERA
50V F 0.01MF Z (TAPPING)
C721
CEXF1E470V
C ELECTRO
C725
CEXF1E470V
C ELECTRO
C802
CCXF3A472Z
C CERA
1KV F 4700PF Z (T)
C803
CCXF3A472Z
C CERA
1KV F 4700PF Z (T)
C804
CCXF3A472Z
C CERA
1KV F 4700PF Z (T)
C805
CCXF3A472Z
C CERA
1KV F 4700PF Z (T)
C808
CEXF2A479V
C ELECTRO
100V RSS 4.7MF (5X11) TP
C810
CEXF1E221V
C ELECTRO
25V RSS 220MF (8X11.5) TP
C812
CCXB3A102K
C CERA
C817
CCXB3A102K
C CERA
C820
CCXB2H471K
C CERA
C822
CCXB2H471K
C CERA
C824
CEXF1E101V
C ELECTRO
25V RSS 100MF (6.3X11) TP
C826
CEXF1E470V
C ELECTRO
C830
CEXF1E101V
C ELECTRO
25V RSS 100MF (6.3X11) TP
C904
CMXL2E104K
C MYLAR
250V MEU 0.1MF K
C905
CMXL2E104K
C MYLAR
250V MEU 0.1MF K
C906
CMXL2E104K
C MYLAR
250V MEU 0.1MF K
C907
CCXB1H561K
C CERA
C908
CCXB1H561K
C CERA
C909
CCXB1H561K
C CERA
F801A
4857415001
CLIP FUSE
PFC5000-0702
F801B
4857415001
CLIP FUSE
PFC5000-0702
QA02
TKTC3198Y-
TR
KTC3198Y
Q101
TKTC3197
TR
KTC3197 (TP)
Q102
TKTC3198Y-
TR
KTC3198Y
Q301
TKTC3198Y-
TR
KTC3198Y
Q302
TKTC3198Y-
TR
KTC3198Y
Q303
TKTC3198Y-
TR
KTC3198Y
Q401
T2SD1207T-
TR
2SD1207-T (TAPPING)
Q501
TKTC3198Y-
TR
KTC3198Y
Q502
TKTC3198Y-
TR
KTC3198Y
Q503
TKTC3198Y-
TR
KTC3198Y
Q504
TKTA1266Y-
TR
KTA1266Y (TP)
Q505
TKTC3198Y-
TR
KTC3198Y
Q506
TKTC3198Y-
TR
KTC3198Y
54
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
Q507
TKTA1266Y-
TR
KTA1266Y (TP)
Q601
TKTC3198Y-
TR
KTC3198Y
Q602
TKTC3198Y-
TR
KTC3198Y
Q603
TKTC3198Y-
TR
KTC3198Y
Q604
TKTC3198Y-
TR
KTC3198Y
Q605
TKTC3198Y-
TR
KTC3198Y
Q606
TKTA1266Y-
TR
KTA1266Y (TP)
Q702
TKTC3202Y-
TR
KTC3202Y (TP)
Q703
TKTC3198Y-
TR
KTC3198Y
Q705
TKTC3198Y-
TR
KTC3198Y
Q706
TKTC3198Y-
TR
KTC3198Y
Q707
TKTC3198Y-
TR
KTC3198Y
Q708
TKTA1266Y-
TR
KTA1266Y (TP)
Q709
TKTA1266Y-
TR
KTA1266Y (TP)
Q710
TKTA1266Y-
TR
KTA1266Y (TP)
Q711
TKTC3198Y-
TR
KTC3198Y
Q713
TKTC3198Y-
TR
KTC3198Y
Q715
TKTC3198Y-
TR
KTC3198Y
Q802
TKTC3198Y-
TR
KTC3198Y
Q803
TKTC3198Y-
TR
KTC3198Y
X501
5XEX4R436C
CRYSTAL QUARTZ
HC-49U 4.433619M 20PP TA
X502
5XEX3R579C
CRYSTAL QUARTZ
HC-49U 3.579545M (TP)
Z501
5PXPS45MB-
FILTER CERA
TPS-4.5MB TRAP (TAPPING)
Z502
5PXPS5R5MB
FILTER CERA
TPS5.5MB-TF21 (TP)
Z601
5PXFSH5R5M
FILTER CERA
SFSH5.5MCB-TF21 (TP)
Z602
5PXFSH6R5M
FILTER CERA
Z603
5PXFSH4R5M
FILTER CERA
Z604
5PXFSH6R0M
FILTER CERA
ZZ200
PTMPJAA499
PCB MAIN AXIAL AS
DTC-14Q1VM
A001
4859811892
PCB MAIN
330X246 S1B
CA02
CCZB1H561K
C CERA
50V B 560PF K (AXIAL)
CA03
CBZF1H104Z
C CERA SEMI
50V F 0.1MF Z (AXIAL)
C101
CCZB1H102K
C CERA
C102
CCZF1E103Z
C CERA
C106
CCZF1E103Z
C CERA
C108
CCZF1E103Z
C CERA
C110
CCZF1E103Z
C CERA
C112
CCZF1E103Z
C CERA
C113
CCZF1E103Z
C CERA
C114
CCZB1H331K
C CERA
C118
CZCH1H100J
C CERA
50V CH 10PF J (AXIAL)
C120
CCZB1H102K
C CERA
C121
CCZF1E103Z
C CERA

55
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
C122
CBZF1H104Z
C CERA SEMI
C302
CCZB1H181K
C CERA
C303
CCZB1H181K
C CERA
C401
CBZR1C472M
C CERA
16V Y5R 4700PF M (AXIAL)
C403
CBZR1C222M
C CERA
C404
CBZR1C222M
C CERA
C405
CCZF1E103Z
C CERA
C501
CBZF1H104Z
C CERA SEMI
C511
CCZB1H181K
C CERA
C513
CBZF1H104Z
C CERA SEMI
C515
CZCH1H180J
C CERA
C516
CBZF1H104Z
C CERA SEMI
C517
CBZR1C472M
C CERA
C518
CZCH1H180J
C CERA
C519
CBZF1H104Z
C CERA SEMI
C520
CBZF1H104Z
C CERA SEMI
C521
CCZB1H102K
C CERA
C522
CCZB1H102K
C CERA
C523
CCZF1E223Z
C CERA
C524
CBZF1H104Z
C CERA SEMI
C528
CCZF1E103Z
C CERA
C601
CCZB1H102K
C CERA
C605
CZSL1H560J
C CERA
50V SL 56PF J (AXIAL)
C606
CZSL1H680J
C CERA
C613
CCZF1E103Z
C CERA
C616
CBZR1C392M
C CERA
C703
CZCH1H150J
C CERA
C704
CZCH1H150J
C CERA
C705
CCZF1E103Z
C CERA
C709
CCZB1H102K
C CERA
C720
CCZF1E103Z
C CERA
C722
CZSL1H390J
C CERA
C723
CZSL1H390J
C CERA
C724
CCZF1E103Z
C CERA
C726
CCZB1H331K
C CERA
C727
CCZB1H561K
C CERA
C825
CCZF1E103Z
C CERA
C827
CCZF1E103Z
C CERA
C829
CCZF1E103Z
C CERA
C831
CBZF1H104Z
C CERA SEMI
DA01
DUZ6R2BM
DIODE ZENER
UZ-6.2BM 6.2V
DA02
DUZ9R1BM
DIODE ZENER
UZ-9.1BM 9.1V
DA03
DUZ6R2BM
DIODE ZENER
UZ-6.2BM 6.2V
56
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
DA04
DUZ9R1BM
DIODE ZENER
UZ-9.1BM 9.1V
DA06
DUZ9R1BM
DIODE ZENER
UZ-9.1BM 9.1V
DA09
DUZ9R1BM
DIODE ZENER
UZ-9.1BM 9.1V
DO401
DUZ5R1BM
DIODE ZENER
UZ-5.1BM
D102
D1N4148-
DIODE
1N4148 (TAPPING)
D301
DUZ5R1BM
DIODE ZENER
UZ-5.1BM
D401
DBYV95C-
DIODE
BYV95C (TAPPING)
D402
DBYV95C-
DIODE
BYV95C (TAPPING)
D403
DBYV95C-
DIODE
BYV95C (TAPPING)
D404
D1N4148-
DIODE
1N4148 (TAPPING)
D405
D1N4148-
DIODE
1N4148 (TAPPING)
D406
D1N4148-
DIODE
1N4148 (TAPPING)
D409
DBYV95C-
DIODE
BYV95C (TAPPING)
D501
DUZ5R1BM
DIODE ZENER
UZ-5.1BM
D502
D1N4148-
DIODE
1N4148 (TAPPING)
D503
D1N4148-
DIODE
1N4148 (TAPPING)
D504
D1N4148-
DIODE
1N4148 (TAPPING)
D505
D1N4148-
DIODE
1N4148 (TAPPING)
D506
D1N4148-
DIODE
1N4148 (TAPPING)
D507
D1N4148-
DIODE
1N4148 (TAPPING)
D508
D1N4148-
DIODE
1N4148 (TAPPING)
D510
D1N4148-
DIODE
1N4148 (TAPPING)
D602
D1N4148-
DIODE
1N4148 (TAPPING)
D603
D1N4148-
DIODE
1N4148 (TAPPING)
D604
D1N4148-
DIODE
1N4148 (TAPPING)
D605
D1N4148-
DIODE
1N4148 (TAPPING)
D701
D1N4148-
DIODE
1N4148 (TAPPING)
D702
D1N4148-
DIODE
1N4148 (TAPPING)
D703
D1N4148-
DIODE
1N4148 (TAPPING)
D704
D1N4148-
DIODE
1N4148 (TAPPING)
D705
DUZ6R2BM
DIODE ZENER
UZ-6.2BM 6.2V
D708
DUZ6R2BM
DIODE ZENER
UZ-6.2BM 6.2V
D709
DUZ6R2BM
DIODE ZENER
UZ-6.2BM 6.2V
D710
DUZ6R2BM
DIODE ZENER
UZ-6.2BM 6.2V
D711
DUZ6R2BM
DIODE ZENER
UZ-6.2BM 6.2V
D801
D1S1888-
DIODE
1S1888 (TAPPING)
D802
D1S1888-
DIODE
1S1888 (TAPPING)
D803
D1S1888-
DIODE
1S1888 (TAPPING)
D804
D1S1888-
DIODE
1S1888 (TAPPING)
D807
DBYV95C-
DIODE
BYV95C (TAPPING)
D808
DBYV95C-
DIODE
BYV95C (TAPPING)
D809
DBYV95C-
DIODE
BYV95C (TAPPING)
D811
DBYV95C-
DIODE
BYV95C (TAPPING)
57
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
D813
DBYV95C-
DIODE
BYV95C (TAPPING)
D814
DBYV95C-
DIODE
BYV95C (TAPPING)
L101
5CPZ100K04
COIL PEAKING
10UH 10.5MM K (LAL04TB)
L103
5CPZ220K02
COIL PEAKING
22UH K (AXIAL 3.5MM)
L401
5CPZ109M02
COIL PEAKING
1UH M (AXIAL 3.5MM)
L501
5CPZ150K02
COIL PEAKING
L502
5CPZ829K02
COIL PEAKING
8.2UH K (AXIAL 3.5MM)
L503
5CPZ100K02
COIL PEAKING
L604
5CPZ829K02
COIL PEAKING
L701
5CPZ689K02
COIL PEAKING
L802
5MC0000100
COIL BEAD
MD-5 (HC-3550)
RA01
RD-AZ750J-
R CARBON FILM
1/6 75 OHM J
RA02
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
RA03
RD-AZ511J-
R CARBON FILM
1/6 510 OHM J
RA04
RD-AZ302J-
R CARBON FILM
1/6 3K OHM J
RA09
RD-AZ470J-
R CARBON FILM
1/6 47 OHM J
RA11
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
RA15
RD-AZ221J-
R CARBON FILM
1/6 220 OHM J
RO401
RD-AZ124J-
R CARBON FILM
1/6 120K OHM J
R101
RD-AZ470J-
R CARBON FILM
1/6 47 OHM J
R102
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R103
RD-AZ122J-
R CARBON FILM
1/6 1.2K OHM J
R104
RD-AZ122J-
R CARBON FILM
1/6 1.2K OHM J
R105
RD-AZ270J-
R CARBON FILM
1/6 27 OHM J
R106
RD-AZ123J-
R CARBON FILM
1/6 12K OHM J
R107
RD-AZ333J-
R CARBON FILM
1/6 33K OHM J
R108
RD-AZ122J-
R CARBON FILM
1/6 1.2K OHM J
R109
RD-AZ183J-
R CARBON FILM
1/6 18K OHM J
R110
RD-AZ182J-
R CARBON FILM
1/6 1.8K OHM J
R111
RD-AZ104J-
R CARBON FILM
1/6 100K OHM J
R112
RD-AZ104J-
R CARBON FILM
1/6 100K OHM J
R113
RD-AZ221J-
R CARBON FILM
1/6 220 OHM J
R114
RD-AZ563J-
R CARBON FILM
1/6 56K OHM J
R115
RD-AZ562J-
R CARBON FILM
1/6 5.6K OHM J
R116
RD-AZ562J-
R CARBON FILM
1/6 5.6K OHM J
R118
RD-4Z825J-
R CARBON FILM
1/4 8.2M OHM J
R119
RD-4Z825J-
R CARBON FILM
1/4 8.2M OHM J
R301
RN-AZ3902F
R METAL FILM
1/6 39K OHM F
R302
RN-AZ1801F
R METAL FILM
1/6 1.8K OHM F
R304
RD-4Z189J-
R CARBON FILM
1/4 1.8 OHM J
R305
RD-4Z189J-
R CARBON FILM
1/4 1.8 OHM J
R308
RD-AZ302J-
R CARBON FILM
1/6 3K OHM J
R309
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J

58
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
R310
RD-4Z392J-
R CARBON FILM
1/4 3.9K OHM J
R311
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R312
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R313
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R314
RD-4Z223J-
R CARBON FILM
1/4 22K OHM J
R401
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R402
RD-AZ153J-
R CARBON FILM
1/6 15K OHM J
R403
RD-AZ479J-
R CARBON FILM
1/6 4.7 OHM J
R404
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R405
RD-AZ152J-
R CARBON FILM
1/6 1.5K OHM J
R406
RD-AZ272J-
R CARBON FILM
1/6 2.7K OHM J
R407
RD-4Z823J-
R CARBON FILM
1/4 82K OHM J
R410
RD-4Z399J-
R CARBON FILM
1/4 3.9 OHM J
R411
85801065GY
WIRE COPPER
AWG22 1/0.65 TIN COATING
R412
85801065GY
WIRE COPPER
R413
85801065GY
WIRE COPPER
R414
RD-2Z273J-
R CARBON FILM
1/2 27K OHM J
R416
RD-AZ303J-
R CARBON FILM
1/6 30K OHM J
R417
RD-4Z102J-
R CARBON FILM
1/4 1K OHM J
R418
RD-AZ393J-
R CARBON FILM
1/6 39K OHM J
R421
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R501
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R502
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R503
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R504
RD-AZ181J-
R CARBON FILM
1/6 180 OHM J
R505
RD-AZ479J-
R CARBON FILM
1/6 4.7 OHM J
R507
RD-4Z109J-
R CARBON FILM
1/4 1 OHM J
R508
RD-AZ301J-
R CARBON FILM
1/6 300 OHM J
R510
RD-AZ222J-
R CARBON FILM
1/6 2.2K OHM J
R511
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R512
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R513
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R514
RD-AZ104J-
R CARBON FILM
1/6 100K OHM J
R518
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R519
RD-AZ470J-
R CARBON FILM
1/6 47 OHM J
R520
RD-AZ203J-
R CARBON FILM
1/6 20K OHM J
R521
RD-AZ104J-
R CARBON FILM
1/6 100K OHM J
R524
RD-AZ303J-
R CARBON FILM
1/6 30K OHM J
R525
RD-AZ121J-
R CARBON FILM
1/6 120 OHM J
R526
RD-4Z479J-
R CARBON FILM
1/4 4.7 OHM J
R527
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R528
RD-AZ182J-
R CARBON FILM
1/6 1.8K OHM J
R529
RD-AZ751J-
R CARBON FILM
1/6 750 OHM J

59
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
R530
RD-AZ203J-
R CARBON FILM
1/6 20K OHM J
R531
RD-AZ682J-
R CARBON FILM
1/6 6.8K OHM J
R532
RD-AZ361J-
R CARBON FILM
1/6 360 OHM J
R533
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R534
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R535
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R536
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R537
RD-AZ241J-
R CARBON FILM
1/6 240 OHM J
R538
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R539
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R540
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R541
RD-AZ331J-
R CARBON FILM
1/6 330 OHM J
R542
RD-AZ331J-
R CARBON FILM
1/6 330 OHM J
R543
RD-AZ331J-
R CARBON FILM
1/6 330 OHM J
R544
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R545
RD-AZ152J-
R CARBON FILM
1/6 1.5K OHM J
R601
RD-AZ471J-
R CARBON FILM
1/6 470 OHM J
R602
RD-AZ561J-
R CARBON FILM
1/6 560 OHM J
R603
RD-AZ562J-
R CARBON FILM
1/6 5.6K OHM J
R604
RD-AZ681J-
R CARBON FILM
1/6 680 OHM J
R605
RD-AZ270J-
R CARBON FILM
1/6 27 OHM J
R606
RD-AZ391J-
R CARBON FILM
1/6 390 OHM J
R607
RD-AZ221J-
R CARBON FILM
1/6 220 OHM J
R608
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R609
RD-AZ221J-
R CARBON FILM
1/6 220 OHM J
R610
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R611
RD-AZ562J-
R CARBON FILM
1/6 5.6K OHM J
R612
RD-AZ562J-
R CARBON FILM
1/6 5.6K OHM J
R613
RD-AZ562J-
R CARBON FILM
1/6 5.6K OHM J
R614
RD-AZ562J-
R CARBON FILM
1/6 5.6K OHM J
R615
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R616
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R617
RD-AZ152J-
R CARBON FILM
1/6 1.5K OHM J
R618
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R619
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R621
RD-AZ223J-
R CARBON FILM
1/6 22K OHM J
R622
RD-AZ182J-
R CARBON FILM
1/6 1.8K OHM J
R623
RD-AZ562J-
R CARBON FILM
1/6 5.6K OHM J
R624
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R626
RD-AZ753J-
R CARBON FILM
1/6 75K OHM J
R627
RD-AZ104J-
R CARBON FILM
1/6 100K OHM J
R701
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R702
RD-AZ272J-
R CARBON FILM
1/6 2.7K OHM J

60
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
R703
RD-AZ272J-
R CARBON FILM
1/6 2.7K OHM J
R705
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R708
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R709
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R710
RD-AZ100J-
R CARBON FILM
1/6 10 OHM J
R711
RD-AZ333J-
R CARBON FILM
1/6 33K OHM J
R715
RD-AZ912J-
R CARBON FILM
1/6 9.1K OHM J
R716
RD-AZ333J-
R CARBON FILM
1/6 33K OHM J
R717
RD-AZ333J-
R CARBON FILM
1/6 33K OHM J
R718
RD-AZ333J-
R CARBON FILM
1/6 33K OHM J
R719
RD-4Z333J-
R CARBON FILM
1/4 33K OHM J
R727
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R728
RD-4Z100J-
R CARBON FILM
1/4 10 OHM J
R729
RD-AZ333J-
R CARBON FILM
1/6 33K OHM J
R730
RD-AZ333J-
R CARBON FILM
1/6 33K OHM J
R731
RD-AZ333J-
R CARBON FILM
1/6 33K OHM J
R732
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R733
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R734
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R735
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R736
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R737
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R738
RD-AZ222J-
R CARBON FILM
1/6 2.2K OHM J
R739
RD-AZ222J-
R CARBON FILM
1/6 2.2K OHM J
R740
RD-AZ222J-
R CARBON FILM
1/6 2.2K OHM J
R741
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R742
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J
R743
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R744
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R745
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R746
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R747
RD-AZ152J-
R CARBON FILM
1/6 1.5K OHM J
R748
RD-AZ202J-
R CARBON FILM
1/6 2K OHM J
R750
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R752
RD-4Z101J-
R CARBON FILM
1/4 100 OHM J
R753
RD-AZ221J-
R CARBON FILM
1/6 220 OHM J
R754
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R755
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R756
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R757
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R758
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R760
RD-AZ362J-
R CARBON FILM
1/6 3.6K OHM J
R761
RD-AZ472J-
R CARBON FILM
1/6 4.7K OHM J

61
REMARK
LOC.
PART-CODE
PART-NAME
PART TYPE
R762
RD-AZ103J-
R CARBON FILM
1/6 10K OHM J
R763
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R764
RD-AZ101J-
R CARBON FILM
1/6 100 OHM J
R765
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R766
RD-AZ104J-
R CARBON FILM
1/6 100K OHM J
R767
RD-AZ471J-
R CARBON FILM
1/6 470 OHM J
R807
RD-4Z330J-
R CARBON FILM
1/4 33 OHM J
R808
RD-4Z182J-
R CARBON FILM
1/4 1.8K OHM J
R810
RD-4Z104J-
R CARBON FILM
1/4 100K OHM J
R813
RD-4Z102J-
R CARBON FILM
1/4 1K OHM J
R826
RD-AZ102J-
R CARBON FILM
1/6 1K OHM J
R829
RD-4Z472J-
R CARBON FILM
1/4 4.7K OHM J
R830
RD-4Z103J-
R CARBON FILM
1/4 10K OHM J
R831
RD-AZ153J-
R CARBON FILM
1/6 15K OHM J
R832
RD-AZ104J-
R CARBON FILM
1/6 100K OHM J
R833
RD-4Z101J-
R CARBON FILM
1/4 100 OHM J
R834
RD-4Z362J-
R CARBON FILM
1/4 3.6K OHM J
R835
RC-2Z565J-
R CARBON COMP
1/2 5.6M OHM J
R901
RD-AZ302J-
R CARBON FILM
1/6 3K OHM J
R902
RD-AZ302J-
R CARBON FILM
1/6 3K OHM J
R903
RD-AZ302J-
R CARBON FILM
1/6 3K OHM J
R904
RD-AZ202J-
R CARBON FILM
1/6 2K OHM J
R905
RD-AZ202J-
R CARBON FILM
1/6 2K OHM J
R906
RD-AZ202J-
R CARBON FILM
1/6 2K OHM J
R907
RD-4Z104J-
R CARBON FILM
1/4 100K OHM J
R908
RD-4Z104J-
R CARBON FILM
1/4 100K OHM J
R909
RD-4Z104J-
R CARBON FILM
1/4 100K OHM J
R910
RD-2Z152J-
R CARBON FILM
1/2 1.5K OHM J
R911
RD-2Z152J-
R CARBON FILM
1/2 1.5K OHM J
R912
RD-2Z152J-
R CARBON FILM
1/2 1.5K OHM J
REMARK
# FRONT A/V PART LIST (OPTION)

LOC.
PART-CODE
PART-NAME
PART-DESCRIPTION
J177
85801065GY-
WIRE COPPER
J121
85801065GY-
WIRE COPPER
J124
85801065GY-
WIRE COPPER
J125
85801065GY-
WIRE COPPER
J136
85801065GY-
WIRE COPPER
J137
85801065GY-
WIRE COPPER
DA10
DU1Z9R1BM-
DIODE ZENER
UZ-9.1BM
DA11
DU1Z9R1BM-
DIODE ZENER
UZ-9.1BM
62
REMARK
Not Used
LOC.
PART-CODE
PART-NAME
PART-DESCRIPTION
R625
RD-AZ221J-
R CARBON FILM
1/4 220 OHM J
R628
RD-AZ221J-
R CARBON FILM
1/4 220 OHM J
C621
CEXF1E470V
C ELECTRO
25V RSS 47MF
C623
CEXF1E470V
C ELECTRO
25V RSS 47MF
P603
4859231725
CONN WAFER
YW025-04 (STICK)
PA603
4850704S03
CONN ASSY
YH025-04+YST025+TURE=300
JV02
4859108350
JACK PIN BOARD
YSC-02P-4100-14A
HP01
4859102130
JACK EARPHONE
YSC-1537
63
REMARK
Q / T Difference Part List

NO
LOC
PART NAME
Q MODEL(1spk)
T MODEL(2spk)
I601
IC AMP
TDA 7056
TDA 1519B
I601A
HEAT SINK
4857025400(A1050P-H24 T2)
4857026402(AL EX BK)
PA601
CONN AS
YH025-03+YST025+ULW=200
YH025-03+YST025+ULW=300
PA602
CONN AS
YH025-03+YST025+ULW=600
SP01
SPEAKER
SP02
SPEAKER
95BF03LC
P602
CONN WAFER
YW025-03(STICK)
C613
C CERA
J175,J207,J209 WIRE COPPER
3W 16 F2035C03-3
7.5W 8 95BF03LC
25V 0.01F Z(AXIAL)

-
J210,J212,J214
10
J176,J205,J206
J208,J211,J213 WIRE COPPER
J215
11
R620
R CARBON
1/6W 56K
12
C620
C MYLAR
100V 0.1F J
13
C612
C MYLAR
100V 0.022F J
14
C619
C ELECTRO
50V RSS 47MF
15
R621
R CARBON
1/6W 22K
64
1/6W 18K
CP-370 Inch Difference Part List

NO
LOC
PART NAME
14 MODEL
20 MODEL
R407
R-CARBON
1/4W 82K
1/4W 68K
1/4W 68K
ABL
C410
C-MYLAR
1.6KV 6900PF
1.6KV 7500PF J
1.6KV 6000PF
H.V
C411
C-MYLAR
200V 0.33MF J
200V 0.36MF J
200V 0.3MF
H.V
R415
R-FUSIBLE
1W 1.2OHM
1W 2.2OHM
1W 1.2OHM
HEATER
R901
R-CARBON
1/6W 3K
1/6W 2K
1/6W 2K
R, G, B
R902
R-CARBON
1/6W 3K
1/6W 2K
1/6W 2K
R, G, B
R903
R-CARBON
1/6W 3K
1/6W 2K
1/6W 2K
R, G, B
R904
R-CARBON
1/6W 2K
1/6W 1.6K
1/6W 1.6K
R, G, B
R905
R-CARBON
1/6W 2K
1/6W 1.6K
1/6W 1.6K
R, G, B
10
R906
R-CARBON
1/6W 2K
1/6W 1.6K
1/6W 1.6K
R, G, B
11
R834
R-CARBON
1/4W 3.6K
1/4W 3.3K
1/4W 3.3K
12
L901
COIL/D
DC-1450
DC-2050
DC-2070
13
13100
CRT GND AS
1401H-1015-1P
2001H-1015-1P
2101H-1015-1P
14
V801
CRT BARE
A34JLL90X
A48JLL90X
A51JLL90X
15
CRT1
CRT AS
14Q1VM
20Q1VM
21Q1VM
16
J187
WIRE COPPER
17
J218
WIRE COPPER WIRE COPPER
WIRE COPPER
18
R302
R-CARBON
1/6W 1.8K
1/6W 2.0K
1/6W 2.4K
V-SIZE(1%R)
19
P401
WAFER
YFW-500-05
YFW500-05
YFW500-06
D.Y
65
21 MODEL
WIRE COPPER
-
REMARK
B+:110V
B+:123V

Daewoo 14Q1

Uploaded by

Copyright:

Available Formats

Daewoo 14Q1

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Daewoo 14Q1

Uploaded by

Copyright:

Available Formats

Service Manual

38 / 48 / 51 Cm Mono Colour Television

Downloaded from www.Manualslib.com manuals search engine

Trouble Shooting Charis ............................................................................................. 40

Downloaded from www.Manualslib.com manuals search engine

PAL/SECAM-B/G, D/K, I, H, NTSC-3.58/4.43

100~250V AC, 50/60Hz

14Q = 69W, 14T = 74W

. 1 Speaker : 3W( at 80% MOD. 10% THD)

. 1 Speaker : 3W, 16 ohm

300 ohm balanced with supplied balun

Voltage Synthesize Tuning System

VM : 100 channels, TM : 70 channels

VHF - L : CH2 - CH4

VHF - H : CH5 - CH12

14 : 34cm (A34JLL 90 02)

X-RAY RADIATION PRECAUTION

voltage should be checked. It is recommended

2. If any Fuse in this TV receiver is blown, replace it

PRODUCT SAFETY NOTICE

identified by designated symbol on the parts list.

6.2 VERTICAL SIZE

6.3 VERTICAL SLOPE

6.4 VERTICAL S-CORRECTION

6.5 HORIZONTAL CENTER

If EEPROM(1703) has been changed ;

09 CMOS Compatible I/O Pins

DW5255M*(Micro-controller & West/East Teletext Decoder)

(4) Pin Description

NTSC OUT for switching SAW filter

I2C BUS STOP IN for Computer

Serial data IN/OUT for I2C

Serial clock IN/OUT for I2C

PWM1-0/ Open Drain

PWM1-1/ Open Drain

LED drive OUT

Input to inverting osc. Amplifier

Output of inverting osc. Amplifier

RESET IN (ACTIVE LOW)

TUNING VOLTAGE OUT

AUDIO MUTE OUT

(Must be tied 0V for DW370M*)

Analog GND for Slicer

PLL Loop Filter I/O for Phase Shifting

PLL Loop Filter I/O for TTX Slicing

PLL Loop Filter I/O for VPS Slicing

Analog Supply for Slicer

Reference Current for Slicer PLLs

P2.3/8 bit ADC

P2.2/8 bit ADC

P2.1/8 bit ADC

Local KEY SCAN IN

P2.0/8 bit ADC

CLOCK IN for OSD

CLOCK OUT for OSD

BAND VHF-L OUT ( Active High )

BAND VHF-H OUT ( Active High )

BAND UHF OUT ( Active High )

POWER CONTROL OUT