BLDC MotorBackground

D C Brush Motors
The history of the DC motor can be traced back to

the 1830s, when Michael Faraday did extensive
work with disc type machines (Fig. 1.21).
Fig. 1.21 Sim ple disc motor
Conductive Disc
P r a c ti c a l C o n si d e r a tio n s
The problem now is that of using this force to
produce the continuous torque required in a
practical motor.
To achieve maximum performance from the motor,
the maximum number of conductors must be
placed in the magnetic field, to obtain the greatest
possible force. In practice, this produces a cylinder
of wire, with the windings running parallel to the axis
of the cylinder. A shaft is placed down this axis to
act as a pivot, and this arrangement is called the
motor armature (Fig. 1.23).
Fig. 1.23 D C motor arm ature

S
Magnet
Brush
Resultant
Field Due to
Armature
Current
Shaft
This design was quickly improved, and by the end

of the 19th century the design principles of DC
motors had become well established.
About that time; however, AC power supply
systems came into general use and the popularity
of the DC motor declined in favor of the less
expensive AC induction motor. More recently, the
particular characteristics of DC motors, notably high
starting torque and controllability, have led to their
application in a wide range of systems requiring
accurate control of speed and position. This
process has been helped by the development of
sophisticated modern drive and computer control
systems.
P ri n c i p l e s
It is well known that when a current-carrying
conductor is placed in a magnetic field, it
experiences a force (Fig. 1.22).
Fig. 1.22 F orc e on a c onductor in a

m a gnetic field
Magnetic Field (B)
Armature
Direction
of Current
Into Page
Stator Field
As the armature rotates, so does the resultant

magnetic field. The armature will come to rest with
its resultant field aligned with that of the stator field,
unless some provision is made to constantly
change the direction of the current in the individual
armature coils.
C o m m u t a tio n
The force that rotates the motor armature is the
result of the interaction between two magnetic
fields (the stator field and the armature field). To
produce a constant torque from the motor, these
two fields must remain constant in magnitude and
in relative orientation.
Fig. 1.24 Ele ctric al arrang e m ent of the arm ature

2
Conductor
Carrying
Current (I)
(Into Page)
Force (F)
Force on Conductor F = I x B
The force acting on the conductor is given by:

F=IxB
where B = magnetic flux density and I = current
If this single conductor is replaced by a large
number of conductors (i.e., a length of wire is
wound into a coil), the force per unit length is
increased by the number of turns in the coil. This is
the basis of a DC motor.
E n gi n e e ri n g R e f e r e n c e
Motor Technologies
Current
In
Out
6
4
5
This is achieved by constructing the armature as a

series of small sections connected in sequence to
the segments of a commutator (Fig 1.24). Electrical
connection is made to the commutator by means of
two brushes. It can be seen that if the armature
rotates through 1/6 of a revolution clockwise, the
current in coils 3 and 6 will have changed direction.
As successive commutator segments pass the
brushes, the current in the coils connected to those
segments changes direction. This commutation or
switching effect results in a current flow in the
A13
Motor Technologies
armature that occupies a fixed position in space,
independent of the armature rotation, and allows
the armature to be regarded as a wound core with
an axis of magnetization fixed in space. This gives
rise to the production of a constant torque output
from the motor shaft.
The axis of magnetization is determined by the
position of the brushes. If the motor is to have similar
characteristics in both directions of rotation, the
brush axis must be positioned to produce an axis of
magnetization that is at 90 to the stator field.
D C Motor Typ e s
Brushless. The major limiting factor in the

performance of iron-cored motors is internal
heating. This heat escapes through the shaft and
bearings to the outer casing, or through the airgap
between the armature and field magnets and from
there to the casing. Both of these routes are
thermally inefficient, so cooling of the motor
armature is very poor.
Fig. 1.28 Brushless motor

Backiron
Return
Path
Several different types of DC motor are currently

in use.
Iron cored. (Fig. 1.25). This is the most common

type of motor used in DC servo systems. It is made
up of two main parts; a housing containing the field
magnets and a rotor made up of coils of wire
wound in slots in an iron core and connected to a
commutator. Brushes, in contact with the
commutator, carry current to the coils.
Fig. 1.25 Iron-c ore d motor
Magnets
Stator
Lam Teeth
Stator Magnets
Windings
In the brushless motor, the construction of the iron

cored motor is turned inside out, so that the rotor
becomes a permanent magnet and the stator
becomes a wound iron core.
Rotor Winding
Commutator
Brushes
Moving coil. There are two principle forms of this

type of motor. 1. The printed motor (Fig. 1.26),
using a disc armature. 2. The shell type armature
(Fig. 1.27).
Since these types of motors have no moving iron in
their magnetic field, they do not suffer from iron
losses. Consequently, higher rotational speeds can
be obtained with low power inputs.
Fig. 1.26 Disc-arm ature printe d motor

Motion
The current-carrying coils are now located in the

housing, providing a short, efficient thermal path to
the outside air. Cooling can further be improved by
finning the outer casing and blowing air over it if
necessary (to effectively cool an iron-cored motor, it
is necessary to blow air through it.) The ease of
cooling the brushless motor allows it to produce a
much higher power in relation to its size.
The other major advantage of brushless motors is
their lack of a conventional commutator and brush
gear. These items are a source of wear and
potential trouble and may require frequent
maintenance. By not having these components, the
brushless motor is inherently more reliable and can
be used in adverse environmental conditions.
To achieve high torque and low inertia, brushless
motors do require rare earth magnets that are
much more expensive than conventional ceramic
magnets. The electronics necessary to drive a
brushless motor are also more complex than for a
brush motor. A more thorough explanation of
brushless motors is provided on page A17.
Permanent magnet
(8 pole)
Fig. 1.27 Shell-arm ature motor

Magnet pole
Air gap
Core
Motion
Armature
(Hollow cup, shaped
conductor array)
Dia gra ms c ourtesy of Ele ctro- Craft Ltd.
A14
Flux path
Loss e s in D C Motors
DC motors are designed to convert electrical power
into mechanical power and as a consequence of
this, during periods of deceleration or if externally
driven, will generate electrical power. However, all
the input power is not converted into mechanical
power due to the electrical resistance of the
armature and other rotational losses. These losses
give rise to heat generation within the motor.
Motor losses can be divided into two areas: Those

that depend on the load and those that depend on
speed (Fig. 1.29).
Fig. 1.29 Losses in a D C motor

Motor losses
Load
Short circuit currents. As the brushes slide over

the commutator, the brush is in contact with two
commutator segments for a brief period. During this
period, the brush will short out the coil connected
to those segments (Fig. 1.30). This condition
generates a torque that opposes the main driving
torque and increases with motor speed.
Fig. 1.30 G eneration of short-circuit currents
Speed
Commutator
Brush
Winding
losses
Friction
losses
Brush
losses
Short-cut
circuit losses
Iron
losses
Winding losses. These are caused by the electrical

resistance of the motor windings and are equal to
I2R (where I = armature current and R = armature
resistance).
As the torque output of the motor increases, I
increases, which gives rise to additional losses.
Consideration of winding losses is very important
since heating of the armature winding causes an
increase in R, which results in further losses and
heating. This process can destroy the motor if the
maximum current is not limited. Furthermore, at
higher temperatures, the field magnets begin to
lose their strength. Hence, for a required torque
output the current requirement becomes greater.
Brush contact losses. These are fairly complex to
analyze since they depend upon several factors that
will vary with motor operation. In general, brush
contact resistance may represent a high proportion
of the terminal resistance of the motor. The result of
this resistance will be increased heating due to I2R
losses in the brushes and contact area.
Iron losses. Iron losses are the major factor in
determining the maximum speed that may be
attained by an iron-cored motor. These fall into two
categories:
Eddy current losses are common in all
conductive cored components experiencing a
changing magnetic field. Eddy currents are
induced into the motor armature as it undergoes
changes in magnetization. These currents are
speed-dependent and have a significant heating
effect at high speeds. In practice, eddy currents
are reduced by producing the armature core as a
series of thin, insulated sections or laminations,
stacked to produce the required core length.
Hysteresis losses are caused by the resistance
of the core material to constant changes of
magnetic orientation, giving rise to additional heat
generation, which increases with speed.
Friction losses. These are associated with the
mechanical characteristics of the motor and arise
from brush friction, bearing friction, and air
resistance. These variables will generate heat and
will require additional armature current to offset this
condition.
E n gi n e e ri n g R e f e r e n c e
Motor Technologies
Winding
All these losses will contribute heat to the motor

and it is this heating that will ultimately limit the
motor application.
O t h e r Li m iti n g C o n si d e r a tio n s
Torque ripple. The requirement for constant torque
output from a DC motor is that the magnetic fields
due to the stator and the armature are constant in
magnitude and relative orientation, but this ideal is
not achieved in practice. As the armature rotates,
the relative orientation of the fields will change
slightly and this will result in small changes in torque
output called torque ripple (Fig. 1.31).
Fig. 1.31 Torque rip ple c om ponents

Torque
Torque Ripple
Steady Torque
O/P
Time
This will not usually cause problems at high speeds

since the inertia of the motor and the load will tend
to smooth out the effects, but problems may arise
at low speeds.
Motors can be designed to minimize the effects of
torque ripple by increasing the number of windings,
or the number of motor poles, or by skewing the
armature windings.
A15
Motor Technologies
Demagnetization. The permanent magnets of a
DC motor field will tend to become demagnetized
whenever a current flows in the motor armature.
This effect is known as armature reaction and will
have a negligible effect in normal use. Under high
load conditions, however, when motor current may
be high, the effect will cause a reduction in the
torque constant of the motor and a consequent
reduction in torque output.
Above a certain level of armature current, the field
magnets will become permanently demagnetized.
Therefore, it is important not to exceed the
maximum pulse current rating for the motor.
Mechanical resonances and backlash. It might
normally be assumed that a motor and its load,
including a tachometer or position encoder, are all
rigidly connected together. This may, however, not
be the case.
M o t o r E q u a tio n s
Unlike a step motor, the DC brush motor exhibits
simple relationships between current, voltage,
torque and speed. It is therefore worth examining
these relationships as an aid to the application of
brush motors.
The application of a constant voltage to the
terminals of a motor will result in its accelerating to
attain a steady final speed (n). Under these
conditions, the voltage (V) applied to the motor is
opposed by the back emf (nKE) and the resultant
voltage drives the motor current (I) through the
motor armature and brush resistance (Rs).
The equivalent circuit of a DC motor is shown in
Fig. 1.34.
Fig. 1.34 D C motor e quivalent circuit

L
It is important for a bi-directional drive or positioning

system that the mechanics are free from backlash,
otherwise, true positioning will present problems.
In high-performance systems, with high
accelerations, interconnecting shafts and couplings
may deflect under the applied torque, such that the
various parts of the system may have different
instantaneous velocities that may be in opposite
directions. Under certain conditions, a shaft may go
into torsional resonance (Fig. 1.32).
Fig. 1.32 Torsional oscillation

Shaft
Load
Motor
Tach
B ack e mf
As described previously, a permanent magnet DC
motor will operate as a generator. As the shaft is
rotated, a voltage will appear across the brush
terminals. This voltage is called the back
electromotive force (emf) and is generated even
when the motor is driven by an applied voltage. The
output voltage is essentially linear with motor speed
and has a slope that is defined as the motor voltage
constant, KE (Fig. 1.33). K E is typically quoted in
volts per 1000 rpm.
Fig. 1.33 B a ck-e mf chara cteristic
Output
volts
Shaft speed
A16
Rs
RL
Vg
Rs = motor resistance
L = winding inductance
Vg = back emf and
RL represents magnetic losses.
The value of RL is usually large and so can be
ignored, as can the inductance L, which is generally
small.
If we apply a voltage (V) to the motor and a current
(I) flows, then:
V = IRs + Vg
but
Vg = nKE
so
V = IRs + nK E
(1)
This is the electrical equation of the motor.
If KT is the torque constant of the motor (typically in
oz/in per Amp), then the torque generated by the
motor is given by:
T = IKT
(2)
The opposing torque due to friction (TF) and viscous
damping (KD) is given by:
TM = TF + nKD
If the motor is coupled to a load TL ,then at
constant speed:
T = TL + TF + nKD (3)
Equations (1), (2) and (3) allow us to calculate the
required current and drive voltage to meet given
torque and speed requirements. The values of KT,
KE, etc. are given in the motor manufacturers data.

BLDC MotorBackground

Uploaded by

Copyright:

Available Formats

BLDC MotorBackground

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BLDC MotorBackground

Uploaded by

Copyright:

Available Formats

D C Brush Motors

The history of the DC motor can be traced back to

Fig. 1.21 Sim ple disc motor

Fig. 1.23 D C motor arm ature

This design was quickly improved, and by the end

Fig. 1.22 F orc e on a c onductor in a

As the armature rotates, so does the resultant

Fig. 1.24 Ele ctric al arrang e m ent of the arm ature

The force acting on the conductor is given by:

This is achieved by constructing the armature as a

Brushless. The major limiting factor in the

Fig. 1.28 Brushless motor

Several different types of DC motor are currently

Iron cored. (Fig. 1.25). This is the most common

Fig. 1.25 Iron-c ore d motor

In the brushless motor, the construction of the iron

Moving coil. There are two principle forms of this

Fig. 1.26 Disc-arm ature printe d motor

The current-carrying coils are now located in the

Fig. 1.27 Shell-arm ature motor

Dia gra ms c ourtesy of Ele ctro- Craft Ltd.

Motor losses can be divided into two areas: Those

Fig. 1.29 Losses in a D C motor

Short circuit currents. As the brushes slide over

Fig. 1.30 G eneration of short-circuit currents

Winding losses. These are caused by the electrical

All these losses will contribute heat to the motor

Fig. 1.31 Torque rip ple c om ponents

This will not usually cause problems at high speeds

Fig. 1.34 D C motor e quivalent circuit

It is important for a bi-directional drive or positioning

Fig. 1.32 Torsional oscillation

Fig. 1.33 B a ck-e mf chara cteristic

You might also like