Scribd Logo
Upload

Welcome to Scribd!

  • 422 views

    Edge 540-3d

    Uploaded by

    Joao Junqueira
    .

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Edge 540-3d

    Uploaded by

    Joao Junqueira
    422 views1 page
    .

    Original Title

    edge_540-3d

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    .

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    422 views1 page

    Edge 540-3d

    Uploaded by

    Joao Junqueira
    .

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    1/64" ply doublers on both

    sides of fuselage (see side view)

    6mm Depron Fuse

    Notes on the fuse:


    If you are going for all out light weight, consider leaving
    out the fuse spar. The side plates are strong enough for
    anything in flight, but will not be quite as tough for rough
    landings/crashes. Make sure to use 15-30 minute epoxy or
    shoogoo for the main parts...5 min and foam CA are not
    strongenough, and will crack under the torque.

    3/8"x3/8" Hardwood motor block


    Groove block to fit carbon rod.
    If using GWS 350 Drive, mount
    block on Carbon rod so that the
    prop/drive shaft is in the same
    location as shown on plans.

    Molded Carbon Gear Legs

    3/16" zipties
    6mm Depron Fuse Rails

    4mm Carbon Spar


    HS-56HB

    HS-56HB

    LiPo Battery

    Aileron Servo
    (HS-56HB Shown)
    (1 Each Side)

    Elevator Servo
    (HS-56HB Shown)

    Rudder Servo
    (HS-56HB Shown)

    2100(3s2p)
    Carbon Tail wheel bracket
    1/64 ply gear mount plates
    Use Cotterpin to adjust
    tension on pull-pull system.
    Mount using Dubro EZ Conectors

    Hacker B20-15L shown


    Molded Carbon Fiber Gear

    Vacuum Formed
    Wheel Pants

    Cut Control horns from 1/32"


    ply or a plastic coffee can lid.

    Push/Pull

    Hacker B20-15L shown

    1/16" wire wheel axel/steering arm


    (Bend 90 deg. at the top to form
    a control arm. Use clamp on ball
    link to attach to rudder control horn)

    Pull Pull

    Motor/Battery Info
    All hinging for control surfaces can be packing
    tape or actual hinges. I prefer robart hinge
    points epoxied in place for the added longivity
    and control freeness.

    Motor Gearing Prop Battery Amp Draw Thrust


    GWS EPS350C DS (6.6:1) GWS 12x6 2s1p Lipo 9.5 17.1 oz.
    GWS EPS350C DS (6.6:1) GWS 11x4.7 3s1p Lipo 11.5 24.3 oz.
    Hacker B20-26S 4:1 Planetary APC 11x4.7 3s1p LiPo 11 amps 22.1 oz.
    Hacker B20-31S 4:1 Planetary APC 11x4.7 3s1p LiPo 7.7 amps 18.6 oz.
    Hacker B20-15L 4:1 Planetary APC 11x4.7 3s2p LiPo 19.5 amps 38.5 oz.
    Hacker B20-15L 4:1 Planetary APC 11x4.7 2s1p LiPo 10.8 amps 20.6 oz.
    Hacker B20-18L 4:1 Planetary APC 11x4.7 3s1p LiPo 11.7 amps 27.7 oz.
    Hacker B20-18L 4:1 Planetary APC 12x6 3s2p LiPo 19 amps 36.7 oz.
    Razor RZ300 GWS/5.3:1 GWS 11x4.7 2s1p LiPo 8.8 amps 15.7 oz.
    Razor RZ300 GWS/5.3:1 GWS 12x6 2s1p LiPo 9.9 amps 18.5 oz.
    Razor RZ300 GWS/6.6:1 GWS 11x4.7 3s1p LiPo 12 amps 26 oz.
    Razor RZ350 GWS/6.6:1 GWS 12x6 3s1p LiPo 12.4 amps 27 oz.
    Razor RZ350 GWS/6.6:1 GWS 11x4.7 3s1p LiPo 8.7 amps 21.2 oz.
    Razor MicroHeli v2 GWS/6.6:1 GWS 12x6 3s1p LiPo 8.9 amps 22.8 oz.
    PJS 3D 500 Direct APC 10x4.7 3s2p LiPo 16.4 amps 21.9 oz.
    PJS 3D 550 Direct APC 10x4.7 3s2p LiPo 13.8 amps 20.7 oz.
    HiMax HA2015-3600 GWS/5.3:1 GWS 12x6 3s1p LiPo 8.7 amps 20.5 oz.
    HiMax HA2015-3600 GWS/6.6:1 GWS 12x6 3s1p LiPo 6.5 amps 18.5 oz.
    HiMax HA2015-4100 GWS/6.6:1 GWS 12x6 3s1p LiPo 11.2 amps 26.4 oz.
    HiMax HA2015-4100 GWS/5.3:1 GWS 11x4.7 3s1p LiPo 11.6 amps 25.2 oz.
    HiMax HA2015-5400 GWS/6.6:1 GWS 12x6 2s1p LiPo 10.2 amps 17.8 oz.
    HiMax HA2025-3236 3.6:1 Planetary APC 11x4.7 3s2p LiPo 14 amps 29.3 oz.
    HiMax HA2025-3236 3.6:1 Planetary APC 12x6 3s2p LiPo 17 amps 32.2 oz.
    HiMax HA2025-4236 4.3:1 Planetary APC 11x4.7 3s2p Lipo 20.2 amps 38.1 oz.

    Mount Battery Pack


    with 1" Velcro strap.
    Also use adhesive
    Velcro on the side of
    fuselage and back of
    pack to secure in
    place.

    3
    2

    3
    8
    2

    1
    1

    Weight 10.5-15.5 oz.


    Thrust 24-39 oz.
    Radio 4-5 Chanel
    Area 301.4 in2
    Cut a "V" groove
    in foam for
    spars. Pull spar
    through groove
    to make round

    Loading 4.2-7.2 oz/ft2


    WWW.3DFOAMY.COM

    Specs:

    The Edge 540 3D

    3D Foamy

    Copyright 2004 3DFoamy.com.


    All rights reserved.
    Designed and Drawn by Levi Jordan
    Updated: 03/3/04.

    You might also like