Scribd
Upload
163 views

Process Dynamics and Control: Chapter 8 Lectures

This chapter discusses feedback controllers used in process control systems. It begins by describing on-off controllers, which are simple but cause excessive wear due to continuous cycling. Proportional, integral, and derivative (PID) controllers are then introduced. Proportional control reduces error but causes offset, while integral control eliminates offset over time. Derivative control anticipates changes. PID controllers combine all three for the best performance. The chapter covers the transfer functions and characteristics of P, PI, and PID controllers. It also discusses tuning controller parameters and the advantages of automatic vs. manual control modes.

Uploaded by

Muhaiminul Islam
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
163 views

Process Dynamics and Control: Chapter 8 Lectures

This chapter discusses feedback controllers used in process control systems. It begins by describing on-off controllers, which are simple but cause excessive wear due to continuous cycling. Proportional, integral, and derivative (PID) controllers are then introduced. Proportional control reduces error but causes offset, while integral control eliminates offset over time. Derivative control anticipates changes. PID controllers combine all three for the best performance. The chapter covers the transfer functions and characteristics of P, PI, and PID controllers. It also discusses tuning controller parameters and the advantages of automatic vs. manual control modes.

Uploaded by

Muhaiminul Islam
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 33

Chapter 8

Feedback Controllers

Figure 8.1 Schematic diagram for a stirred-tank blending


system.

Chapter 8

On-Off Controllers

Simple
Cheap
Used In residential heating and domestic refrigerators
Limited use in process control due to continuous
cycling of controlled variable excessive wear
on control valve.

On-Off Controllers (continued)

Chapter 8

Synonyms:
two-position or bang-bang controllers.

Controller output has two possible values.


3

Chapter 8

Practical case (dead band)

Basic Control Modes


Next we consider the three basic control modes starting with the
simplest mode, proportional control.

Chapter 8

Proportional Control
In feedback control, the objective is to reduce the error signal to
zero where
e ( t ) = ysp ( t ) ym ( t )
and

e (t )

(8-1)

= error signal

ysp ( t ) = set point


ym ( t ) = measured value of the controlled variable
(or equivalent signal from the sensor/transmitter)
5

Although Eq. 8-1 indicates that the set point can be time-varying,
in many process control problems it is kept constant for long
periods of time.

Chapter 8

For proportional control, the controller output is proportional to


the error signal,

p ( t ) = p + Kce ( t )

(8-2)

where:
p ( t ) = controller output
p = bias (steady-state) value
K c = controller gain (usually dimensionless)

Chapter 8

The key concepts behind proportional control are the following:

Chapter 8

1. The controller gain can be adjusted to make the controller


output changes as sensitive as desired to deviations between
set point and controlled variable;
2. the sign of Kc can be chosed to make the controller output
increase (or decrease) as the error signal increases.
For proportional controllers, bias p can be adjusted, a procedure
referred to as manual reset.
Some controllers have a proportional band setting instead of a
controller gain. The proportional band PB (in %) is defined as
100%
PB =
Kc

(8-3)

In order to derive the transfer function for an ideal proportional


controller (without saturation limits), define a deviation variable
p ( t ) as
p ( t ) =
p (t ) p
(8-4)

Chapter 8

Then Eq. 8-2 can be written as


p ( t ) = K c e ( t )

(8-5)

The transfer function for proportional-only control:


P ( s )
E (s)

= Kc

(8-6)

An inherent disadvantage of proportional-only control is that a


steady-state error occurs after a set-point change or a sustained
disturbance.
9

Integral Control

Chapter 8

For integral control action, the controller output depends on the


integral of the error signal over time,
1
p (t ) = p +
I

0 e ( t *)dt *
t

(8-7)

where I , an adjustable parameter referred to as the integral time


or reset time, has units of time.
Integral control action is widely used because it provides an
important practical advantage, the elimination of offset.
Consequently, integral control action is normally used in
conjunction with proportional control as the proportional-integral
(PI) controller:

1
p ( t ) = p + Kc e ( t ) +
I

0 e ( t *) dt *
t

(8-8)
10

Proportional-Integral (PI) Control


t

p ( t ) = p + K c e ( t ) + e ( t ) dt
I 0

Chapter 8

Response to unit step change in e:

Figure 8.6. Response of proportional-integral controller to


unit step change in e(t).

11

Chapter 8

Integral action eliminates steady-state error


(i.e., offset) Why??? e 0 p is changing with
time until e = 0, where p reaches steady state.

ysp

12

The corresponding transfer function for the PI controller in


Eq. 8-8 is given by
P ( s )

Chapter 8

I s +1
1
= K c 1 +
= Kc

E (s)
s
s

(8-9)

Some commercial controllers are calibrated in terms of 1/ I


(repeats per minute) rather than I (minutes, or minutes per
repeat).
Reset Windup

An inherent disadvantage of integral control action is a


phenomenon known as reset windup or integral windup.
Recall that the integral mode causes the controller output to
change as long as e(t*) 0 in Eq. 8-8.
13

When a sustained error occurs, the integral term becomes


quite large and the controller output eventually saturates.

Chapter 8

Further buildup of the integral term while the controller is


saturated is referred to as reset windup or integral windup.

Derivative Control
The function of derivative control action is to anticipate the future
behavior of the error signal by considering its rate of change.
The anticipatory strategy used by the experienced operator can
be incorporated in automatic controllers by making the
controller output proportional to the rate of change of the error
signal or the controlled variable.

14

Thus, for ideal derivative action,


p (t ) = p + D

de ( t )
dt

(8-10)

Chapter 8

where D , the derivative time, has units of time.


For example, an ideal PD controller has the transfer function:
P ( s )
E (s)

= K c (1 + D s )

(8-11)

By providing anticipatory control action, the derivative mode


tends to stabilize the controlled process.
Unfortunately, the ideal proportional-derivative control
algorithm in Eq. 8-10 is physically unrealizable because it
cannot be implemented exactly.
15

For analog controllers, the transfer function in (8-11) can be


approximated by
P ( s )

Chapter 8

Ds
= K c 1 +

E (s)
s
+

1
D

(8-12)

where the constant typically has a value between 0.05 and


0.2, with 0.1 being a common choice.
In Eq. 8-12 the derivative term includes a derivative mode
filter (also called a derivative filter) that reduces the sensitivity
of the control calculations to high-frequency noise in the
measurement.

16

Proportional-Integral-Derivative (PID) Control


Now we consider the combination of the proportional, integral,
and derivative control modes as a PID controller.

Chapter 8

Many variations of PID control are used in practice.


Next, we consider the three most common forms.
Parallel Form of PID Control

The parallel form of the PID control algorithm (without a


derivative filter) is given by

1
p ( t ) = p + K c e ( t ) +
I

de ( t )
0 e ( t *) dt * + D dt
t

(8-13)

17

The corresponding transfer function is:


P ( s )

Chapter 8

1
= K c 1 +
+ Ds
E (s)
I s

(8-14)

Series Form of PID Control

Historically, it was convenient to construct early analog


controllers (both electronic and pneumatic) so that a PI element
and a PD element operated in series.
Commercial versions of the series-form controller have a
derivative filter that is applied to either the derivative term, as in
Eq. 8-12, or to the PD term, as in Eq. 8-15:
P ( s )

I s + 1 D s + 1
= Kc

E (s)
s
s
+

1
I D

(8-15)
18

Expanded Form of PID Control

In addition to the well-known series and parallel forms, the


expanded form of PID control in Eq. 8-16 is sometimes used:
t

de ( t )

dt

Chapter 8

p ( t ) = p + K c e ( t ) + K I e ( t *) dt * + K D

(8-16)

Features of PID Controllers


Elimination of Derivative and Proportional Kick
One disadvantage of the previous PID controllers is that a
sudden change in set point (and hence the error, e) will cause the
derivative term momentarily to become very large and thus
provide a derivative kick to the final control element.

19

This sudden change is undesirable and can be avoided by basing


the derivative action on the measurement, ym, rather than on the
error signal, e.

Chapter 8

We illustrate the elimination of derivative kick by considering


the parallel form of PID control in Eq. 8-13.
Replacing de/dt by dym/dt gives

1
p ( t ) = p + K c e ( t ) +
I

dym ( t )
0 e ( t *) dt * D dt
t

(8-17)

Reverse or Direct Action


The controller gain can be made either negative or positive.

20

For proportional control, when Kc > 0, the controller output p(t)


increases as its input signal ym(t) decreases, as can be seen by
combining Eqs. 8-2 and 8-1:

Chapter 8

p ( t ) p = K c ysp ( t ) ym ( t )

(8-22)

This controller is an example of a reverse-acting controller.


When Kc < 0, the controller is said to be direct acting because
the controller output increases as the input increases.
Equations 8-2 through 8-16 describe how controllers perform
during the automatic mode of operation.
However, in certain situations the plant operator may decide to
override the automatic mode and adjust the controller output
manually.

21

Chapter 8

Figure 8.11 Reverse


and direct-acting
proportional
controllers. (a) reverse
acting (Kc > 0. (b)
direct acting (Kc < 0)

22

Chapter 8

Example: Flow Control Loop

Assume FT is direct-acting.
1. Air-to-open (fail close) valve ==> ?
2. Air-to-close (fail open) valve ==> ?

23

Automatic and Manual Control Modes

Chapter 8

Automatic Mode
Controller output, p(t), depends on e(t), controller
constants, and type of controller used.
( PI vs. PID etc.)
Manual Mode
Controller output, p(t), is adjusted manually.
Manual Mode is very useful when unusual
conditions exist:
plant start-up
plant shut-down
emergencies
Percentage of controllers "on manual ??
(30% in 2001, Honeywell survey)
24

PID Controller
Ideal controller

Chapter 8

Transfer function (ideal)


t

1
de
p( t ) = p + K c e( t ) + e( t )dt + D
dt
I 0

P(s)
1
= K c 1 +
+ Ds
E(s)
Is

Transfer function (actual)


Is + 1 Ds + 1
P(s)

= K c
E(s)
Is Ds + 1
= small number (0.05 to 0.20)

lead / lag units

25

Chapter 8

Controller Comparison
P

- Simplest controller to tune (Kc).


- Offset with sustained disturbance or setpoint
change.

PI

More complicated to tune (Kc, I) .


Better performance than P
No offset
Most popular FB controller

PID

Most complicated to tune (Kc, I, D) .


Better performance than PI
No offset
Derivative action may be affected by noise
26

Chapter 8

Typical Response of Feedback Control Systems


Consider response of a controlled system after a
sustained disturbance occurs (e.g., step change in
the disturbance variable)

Figure 8.12. Typical process responses with feedback control.


27

Chapter 8

Figure 8.13.
Proportional control:
effect of controller
gain.

Figure 8.15. PID


control: effect of
derivative time.

28

Chapter 8

Figure 8.14. PI control: (a) effect of reset time (b) effect of


controller gain.

29

Position and Velocity Algorithms for Digital PID


Control

Chapter 8

A straight forward way of deriving a digital version of the parallel


form of the PID controller (Eq. 8-13) is to replace the integral and
derivative terms by finite difference approximations,
k

0 e ( t *) dt e j t

(8-24)

de ek ek 1

t
dt

(8-25)

j =1

where:

t = the sampling period (the time between successive


measurements of the controlled variable)
ek = error at the kth sampling instant for k = 1, 2,

30

Chapter 8

There are two alternative forms of the digital PID control


equation, the position form and the velocity form. Substituting (824) and (8-25) into (8-13), gives the position form,

D
t k
pk = p + K c ek + e j +
( ek ek 1 )
t
1 j =1

(8-26)

Where pk is the controller output at the kth sampling instant. The


other symbols in Eq. 8-26 have the same meaning as in Eq. 8-13.
Equation 8-26 is referred to as the position form of the PID
control algorithm because the actual value of the controller output
is calculated.
31

Chapter 8

In the velocity form, the change in controller output is


calculated. The velocity form can be derived by writing the
position form of (8-26) for the (k-1) sampling instant:

D
t k
pk = p + K c ek + e j +
( ek ek 1 )
t
1 j =1

(8-26)

Note that the summation still begins at j = 1 because it is assumed


that the process is at the desired steady state for
j 0 and thus ej = 0 for j 0. Subtracting (8-27) from (8-26)
gives the velocity form of the digital PID algorithm:

D
t
pk = pk pk 1 = K c ( ek ek 1 ) + ek +
( ek 2ek 1 + ek 2 )
t
I

(8-28)
32

The velocity form has three advantages over the position form:

Chapter 8

1. It inherently contains anti-reset windup because the


summation of errors is not explicitly calculated.
2. This output is expressed in a form, pk, that can be utilized
directly by some final control elements, such as a control
valve driven by a pulsed stepping motor.
3. For the velocity algorithm, transferring the controller from
manual to automatic mode does not require any initialization
of the output ( p in Eq. 8-26). However, the control valve (or
other final control element) should be placed in the
appropriate position prior to the transfer.

33

You might also like