1/4

STRUCTURE
PRODUCTSERIES

Silicon Monolithic Integrated Circuit

2-ch Switching Regulator Controller

TYPE

BD9848FV

High Input-voltage ( Vcc=35V)

MOSFET-driver circuit built-indual circuit for step-down output
Built-in circuits for error amplifier reference voltage (1.0 V1%)
5 consecutive over current pulse detection circuit built in.
Soft-start timing adjustable
Master/Slave function
Absolute maximum ratingsTa=25

FEATURES

Item

Symbol

Limits

Unit

Power Supply Voltage

Vcc

36

Power dissipation

Pd

8121

mW

Output pin voltage

VOUT

Vcc-7VVcc

C5V pin voltage

VC5V

Vcc-7VVcc

Operating temperature

Topr

-40+105

Storage temperature

Tstg

-55+150

Tjmax

150

Maximum Junction temperature

*1 Should be deleted by 6.5mW/ at Ta=25 or more. When mounted on a glass epoxy PCB of 70.0mm70.0 mm1.6 mm

Recommended operating range (Ta=25)

Item
Symbol

Min.

Typ.

Vcc

3.6

VOUT

C5V

Power Supply Voltage

Output pin voltage

Max.

Unit

6.0

35

Vcc

Error amplifier input voltage

INV

VREF-0.9

Timing capacitor

CCT

47

3000

pF

100
1500
fosc
0
VCC
VSTB
STB input voltage
0
VREF+0.3
DT
DT input voltage
Vcc-0.2
Vcc+0.2
VOCP
OCP+/- input voltage
CTexternal oscillation waveform
1.9
2.3<VREF
VctH
input voltage range
1.4
1.6<VREF
VctL
Electrical characteristics (Unless otherwise specified, Ta=25VCC=6V)
Oscillation frequency

Item

Symbol

Limits

Unit

kHz
V
V
V
V
V

Conditions

Min.

Typ.

Max.

VREF

2.475

2.500

2.525

Line reg.

10

mV

Vcc=3.6V35V

Load regulation

Load reg.

10

mV

IO=0.1mA2mA

Output max. current

IOMAX

13

mA

VREF=(typ.)0.95

VREF output block

VREF output voltage
Line regulation

REV. C

IO=0.1mA

2/4

Electrical characteristics (Unless otherwise specified, Ta=25VCC=6V)

Item

Symbol

Min.

limits
Typ.

Max.

Unit

Conditions

Triangular wave oscillator block

Oscillation frequency

fOSC

95

106

117

kHz

Frequency variation

fDV

SS pin source current

ISSSO

1.4

2.6

SS=0.5V

SS pin sink current

ISSSI

12

mA

SS=0.5V

Dead time adjustable circuit block

IDT
DT pin input bias current
IDTSI
DT pin sink current

0.1

DT=1.75V

3.3

mA

DT=1.75V, (OCP+)-(OCP-)=0.5V

CCP=1800pF
Vcc=3.6V35V

Soft-start block

UVLO block

Threshold voltage

VUTH

3.0

3.2

3.4

Hysterisis

VUHYS

0.15

0.25

Vcc when rise time

Error Amp block

Non-Inverting

input

reference

Reference voltage variation

INV input bias current

VINV

0.99

1.01

dVinv

mV

INV=FB
Vcc=3.6V35V

IIB

INV=1V

AV

70

85

dB

Output FB voltage (Hi)

VFBH

2.30

VREF

Output FB voltage (Low)

VFBL

0.6

1.3

Output sink current

IFBSI

0.5

1.5

mA

FB=1.25V , INV=1.5V

Output source current

IFBSO

50

105

FB=1.25V , INV=0V

Vt0

1.4

1.5

1.6

On duty 0%

Vt100

1.9

2.1

On duty 100%

Output ON resistance H

RONH

10

RONH=( VCC -OUT)/ Iout, Iout=0.1A

Output ON resistance L

RONL

3.3

10

RONL=(OUT-C5V)/ Iout, Iout=0.1A

C5V clamp voltage

VCLMP

4.5

5.5

VCLMP= VCC-C5V , VCC 7V

0.04

0.05

0.06

Voltage between (OCP+)-(OCP-)

Open loop gain

PWM comparator
Input threshold voltage
fosc=100kHz
Output block

Over current protection circuit (OCP) block

OCP threshold voltage

VOCPTH

IOCP-

0.1

10

OCP+= VCC, OCP-= VCC-0.05V

Delay time for OCP

tdocpth

200

400

nS

OCP-= VCCVCC-0.2V

Min. hold time for OCP

tdocpre

0.8

1.6

mS

OCP-= VCC-0.2VVCC

Threshold voltage for each CH stop

VDTthL

1.1

1.25

1.4

Stand-by mode setting voltage range

VSTBL

0.5

Slave mode setting voltage range

VSTBM

2.4

2.5

2.6

Active(Master) mode setting voltage range

VSTBH

VCC

ISTB

70

100

OCP-input bias current

Stand-by switch block

STB current

DT Pin H/L

STB=6V

Total device

Stand-by current

ICCS

STB=0V

Average current consumption

ICCA

1.5

mA

INV=0V, FB=H, DT=1.75V

Not designed for radiation resistance.

REV. C

3/4

Outline figure

PIN No./ name / function

Pin
No
.

Pin name

type

Lot NO.

SSOP-B20 (Unit : mm)

Block Diagram

CT

External Capacitor pin for timing change

DT2

Dead time setting (CH2)

SS2

Soft-start time setting (CH2)

INV2

Error Amp inverting input (CH2)

FB2

Error Amp output (CH2)

GND

GROUND

OCP2

OCP2

C5V

10

OUT2

CH2 Output

11

OUT1

CH1 Output

BD9848

1 pin Mark

Pin function

Over current error amp inverting input (CH2)

Over current error amp input (CH2)

Vcc

13

OCP1

Power supply input

14

OCP1

15

STB

Over current error amp input (CH1)

Over current error amp inverting input (CH1)

16

FB1

Error Amp output (CH1)

17

INV1

Error Amp inverting input (CH1)

18

SS1

Soft-start time setting (CH1)

19

DT1

Dead time setting (CH1)

20

VREF

STB

Refer p.4 Operation note(9)

OCP1+ OCP1-

VCC
VREF

VCC

STB

OCP1
VREF

5pulse

OCP

C5V

REG
(VCC-5V)

50mV10mV

C5V

C5V

DT1
DT1OFF

FB1

1V10mV

SS1OFF

DT1Low

1.25V

VREF
2A

SS1

DT
+

VCC

+
+ PWM
-

+
+ ERR
-

LS

DRV

OUT1

C5V

INV1

PROTECTION LOGIC

DT1Low

OSC

SS1OFF

200A
+
200A

OCP1
1.5V

TSD

DT1OFF

Hold time
(1.6msec)

2.0V

TSD

UVLO
TSD
VCC

Hold time
(0.2msec)

VREF

2V
1.5V

OCP2

DT2OFF
Hold time
(1.6msec)

CT

C5V

3.2V
2.2V

UVLO

SS2OFF

DT2Low

VCC

VREF
2A

SS2
SS2OFF

+ PWM
+

LS

DT2

VCC

DT2OFF

DT
+

OCP2
DT2Low

5pulse

OUT2

DRV

1V10mV

FB2

UVLO

3V

INV2

+ ERR
+

50mV10mV

C5V

OCP

+
C5V

1.25V

Operation Notes
OCP2+ OCP2-

REV. C

Reference voltage2.5Voutput

VCC

REG
(2.5V)

Stand-by mode control

VREF

Output L voltageVcc-5V

12

VCC

GND

4/4

1) Absolute maximum ratings

Use of the IC in excess of absolute maximum ratings such as the applied voltage or operating temperature range may result in IC
deterioration or damage. Assumptions should not be made regarding the state of the IC (short mode or open mode) when such damage
is suffered. A physical safety measure such as a fuse should be implemented when use of the IC in a special mode where the absolute
maximum ratings may be exceeded is anticipated.
2) GND potential
Ensure a minimum GND pin potential in all operating conditions. In addition, ensure that no pins other than the GND pin carry a voltage
lower than or equal to the GND pin, including during actual transient phenomena.
3) Thermal design
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions.
4) Inter-pin shorts and mounting errors
Use caution when orienting and positioning the IC for mounting on printed circuit boards. Improper mounting may result in damage to the
IC. Shorts between output pins or between output pins and the power supply and GND pin caused by the presence of a foreign object
may result in damage to the IC.
5) Operation in a strong electromagnetic field
Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction.
6) Thermal shutdown circuit (TSD circuit)
This IC incorporates a built-in thermal shutdown circuit (TSD circuit). The TSD circuit is designed only to shut the IC off to prevent
runaway thermal operation. Do not continue to use the IC after operating this circuit or use the IC in an environment where the operation
of the thermal shutdown circuit is assumed.
7) Testing on application boards
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress. Always
discharge capacitors after each process or step. Ground the IC during assembly steps as an antistatic measure, and use similar caution
when transporting or storing the IC. Always turn the IC's power supply off before connecting it to or removing it from a jig or fixture during
the inspection process.
8) Common impedance
Power supply and ground wiring should reflect consideration of the need to lower common impedance and minimize ripple as much as
possible (by making wiring as short and thick as possible or rejecting ripple by incorporating inductance and capacitance).
9) Over Current Protection
The OCP circuit is designed to be very sensitive circuit for protection of an application device. Therefore, it may detect ringing noises
besides the true current signal. This depends on an application circuit and a layout pattern. In this case, the OCP current value is lower
than the designed value. For the measure of this, please use CR filter on OCP input referring the circuit of the technical note.
10) General
Please refer the technical note on designing.
11) IC pin input
This monolithic IC contains P+ isolation and PCB layers between adjacent elements in order to keep them isolated.
P/N junctions are formed at the intersection of these P layers with the N layers of other elements to create a variety of parasitic
elements.
For example, when a resistor and transistor are connected to pins as shown in Fig. 10,
The P/N junction functions as a parasitic diode when GND > (Pin A) for the resistor or GND > (Pin B) for the transistor
(NPN).
Similarly, when GND > (Pin B) for the transistor (NPN), the parasitic diode described above combines with the N layer of
other adjacent elements to operate as a parasitic NPN transistor.
The formation of parasitic elements as a result of the relationships of the potentials of different pins is an inevitable result of the IC's
architecture. The operation of parasitic elements can cause interference with circuit operation as well as IC malfunction and damage.
For these reasons, it is necessary to use caution so that the IC is not used in a way that will trigger the operation of parasitic elements,
such as by the application of voltages lower than the GND (PCB) voltage to input and output pins.

Resistance

Transistor (NPN)

(PinA)

P substrate

Parasitic diode

(PinA)

(PinB)

Parasitic diode

(PinB)

P substrate

Parasitic elements
Other adiacent components

REV. C

Parasitic diode

Notice

Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact us.

ROHM Customer Support System

http://www.rohm.com/contact/

www.rohm.com
2009 ROHM Co., Ltd. All rights reserved.

R0039A