CS215 Lab #7

Semester 2, 2008

Part 1: Basic Subnetting

Objective

How to identify reasons to use a subnet mask

How to distinguish between a default subnet mask and a custom subnet mask

What given requirements determine the subnet mask, number of subnets, and hosts per subnet

What needs to be understood about useable subnets and useable numbers of hosts

How to use the ANDing process to determine if a destination IP address is local or remote

How to identify valid and invalid IP host addresses based on a network number and subnet mask

Background / Preparation
This lab exercise focuses on the basics of IP subnet masks and their use with TCP/IP networks. The
subnet mask can be used to split up an existing network into subnetworks, or subnets. Some of the
primary reasons for subnetting are the following:

Reduce the size of the broadcast domains, which creates smaller networks with less traffic

Allow LANs in different geographical locations to communicate through routers

Provide improved security by separating one LAN from another

Routers separate subnets, and determine when a packet can go from one subnet to another. Each
router a packet goes through is considered a hop. Subnet masks help workstations, servers, and
routers in an IP network determine if the destination host for the packet they want to send is on their
own network or another network. This lab reviews the default subnet mask and then focuses on custom
subnet masks. Custom subnet masks use more bits than the default subnet masks by borrowing these
bits from the host portion of the IP address. This creates a three-part address:

The original network address

The subnet address made up of the bits borrowed

The host address made up of the bits left after borrowing some for subnets

Step 1 Review the structure of IP addresses

If an organization has a Class A IP network address, the first octet, or 8 bits, is assigned and does not
change. The organization can use the remaining 24 bits to define up to 16,777,214 hosts on its
network. This is a lot of hosts. It is not possible to put all of these hosts on one physical network without
separating them with routers and subnets.
It is common for a workstation to be on one network or subnet and a server to be on another. When the
workstation needs to retrieve a file from the server it will need to use its subnet mask to determine the
network or subnet that the server is on. The purpose of a subnet mask is to help hosts and routers
determine the network location where a destination host can be found. Refer to the table below to
review the following information:

The IP address classes

The default subnet masks

The number of networks that can be created with each class of network address

The number of hosts that can be created with each class of network address

CS215 Lab #7

Address
Class

1st Octet
Decimal
Range

1st Octet
High Order
Bits

Network/Host ID
(N=Network,
H=Host)

Default
Subnet Mask

1 126*

N.H.H.H

128 191

10

192 223

D
E

Number
of
Networks

Hosts per
Network
(Usable
Addresses)

255.0.0.0

126
(27 2)

16,777,214
(224 2)

N.N.H.H

255.255.0.0

16,382
(214 2)

65,534
(216 2)

110

N.N.N.H

255.255.255.0

2,097,15
(221 2)

254
(28 2)

224 239

1110

Reserved for Multicasting

240 254

11110

Experimental; used for research

* Class A address 127 cannot be used and is reserved for loopback and diagnostic functions.

Step 2 Review the ANDing process

Hosts and routers use the ANDing process to determine if a destination host is on the same network or
not. The ANDing process is done each time a host wants to send a packet to another host on an IP
network. In order to connect to a server, the IP address of the server or the host name, such as,
http://www.cisco.com, must be known. If the host name is used a Domain Name Server (DNS) will
convert it to an IP address.
First, the source host will compare, or AND, its own IP address to its own subnet mask. The result of
the ANDing is to identify the network where the source host resides. It will then compare the destination
IP address to its own subnet mask. The result of the 2nd ANDing will be the network that the destination
host is on. If the source network address and the destination network address are the same, they can
communicate directly. If the results are different, they are on different networks or subnets. If this is the
case, the source host and the destination host will need to communicate through routers or might not
be able to communicate at all.
ANDing depends on the subnet mask. The subnet mask always uses all ones to represent the network,
or network + subnet, portion of the IP address. A default subnet mask for a Class C network is
255.255.255.0 or 11111111.111111111.111111111.00000000. This is compared to the source IP
address bit for bit. The first bit of the IP address is compared to the first bit of the subnet mask, the
second bit to the second, and so on. If the two bits are both ones, the ANDing result is a one. If the two
bits are a zero and a one, or two zeros, the ANDing result is a zero. Basically, this means that a
combination of 2 ones results in a one, anything else is a zero. The result of the ANDing process is the
identification of the network or subnet number that the source or destination address is on.

Step 3 Two Class C networks using the default subnet mask

This example shows how a Class C default subnet mask can be used to determine which network a
host is on. A default subnet mask does not break an address into subnets. If the default subnet mask is
used, the network is not being subnetted. Host X, the source on network 200.1.1.0 has an IP address of
200.1.1.5. It wants to send a packet to Host Z, the destination on network 200.1.2.0 and has an IP
address of 200.1.2.8. All hosts on each network are connected to hubs or switches and then to a router.
Remember that with a Class C network address, the first 3 octets, or 24 bits, are assigned as the
network address. So, these are two different Class C networks. This leaves one octet, or 8 bits for
hosts, so each Class C network could have up to 254 hosts:

28 = 256 2 = 254

Source net:

200.1.1.0

Destination net:

200.1.2.0

Subnet mask:

255.255.255.0

Subnet mask:

255.255.255.0

CS215 Lab #7

Host
X

Hub

Router

Host
Z

Hub

Host IP 200.1.2.8

Host IP 200.1.1.5
Router interface
IP 200.1.1.1

Router interface
IP 200.1.2.1

The ANDing process helps the packet get from Host 200.1.1.5 on network 200.1.1.0 to Host 200.1.2.8
on network 200.1.2.0 by using the following steps:
1. Host X compares its own IP address to its own subnet mask using the ANDing process.
Host X IP address 200.1.1.5

11001000.00000001.00000001.00000101

Subnet Mask 255.255.255.0

11111111.11111111.11111111.00000000

ANDing Result (200.1.1.0)

11001000.00000001.00000001.00000000

Note: The result of the ANDing process is the network address of Host X, which is 200.1.1.0.
2. Next, Host X compares the IP address of the Host Z destination to its own subnet mask using the
ANDing process.
Host Z IP address 200.1.2.8

11001000.00000001.00000010.00001000

Subnet Mask 255.255.255.0

11111111.11111111.11111111.00000000

ANDing Result (200.1.2.0)

11001000.00000001.00000010.00000000

Note: The result of the ANDing process is the network address of Host Z, which is 200.1.2.0.
Host X compares the ANDing results from Step 1 and the ANDing results from Step 2, and notes they
are different. Host X now knows that Host Z is not in its local-area network (LAN). Therefore, it must
send the packet to its default gateway, which is the IP address of the router interface of 200.1.1.1 on
network 200.1.1.0. The router then repeats the ANDing process to determine which router interface to
send the packet out to.

Step 4 One Class C network with subnets using a custom subnet mask
This example uses a single Class C network address (200.1.1.0) and shows how a Class C custom
subnet mask can be used to determine which subnetwork (or subnet) a host is on and to route packets
from one subnetwork to another. Remember that with a Class C network address, the first 3 octets, or
24 bits are assigned as the network address. This leaves one octet, or 8 bits, for hosts. So, each Class
C network could have up to 254 hosts:

28 = 256 2 = 254

Perhaps less than 254 hosts, workstations and servers combined, are desired on one network. This
could be for security reasons or to reduce traffic. It can be done by creating two subnetworks and
separating them with a router. This will create smaller independent broadcast domains and can improve
network performance and increase security. This is possible because these subnetworks will be
separated by one or more router. Assume at least two subnetworks will be needed and that there will
be at least 50 hosts per subnetwork. Because there is only one Class C network address, only 8 bits in
the fourth octet are available for a total of 254 possible hosts. Therefore, a custom subnet mask must
be created. The custom subnet mask will be used to borrow bits from the host portion of the address.
The following steps help accomplish this:
1. The first step to subnetting is to determine how many subnets are needed. In this case, its two
subnetworks. To see how many bits should be borrowed from the host portion of the network
address, add the bit values from right to left until the total is equal to or greater than the number of
subnets needed. Because two subnets are needed, add the one bit and the two bit, which equals
three. This is greater than the number of subnets needed. To remedy this, borrow at least two bits
from the host address starting from the left side of the octet that contains the host address.

CS215 Lab #7

Network address: 200.1.1.0

4th octet Host address bits:

Host address bit values

(from right)

128

64

32

16

Add bits starting from the right side, the 1 and the 2, until the sum is greater than the number of subnets
needed.
Note: An alternate way to calculate the number bits to be borrowed for subnets is to take
the number of bits borrowed to the power of 2. The result must be greater than the number
of subnets needed. As an example if 2 bits are borrowed the calculation is two to the
second power, which equals four. Since the number of subnets needed is two this should
be adequate.
2. After we know how many bits to borrow, we take them from the left side of the of the host address,
the 4th octet. Every bit borrowed from the host address bit leaves fewer bits for the hosts. Even
though the number of subnets is increased, the number of hosts per subnet is decreased. Because
two bits need to be borrowed from the left side, that new value must be shown in the subnet mask.
The existing default subnet mask was 255.255.255.0 and the new custom subnet mask is
255.255.255.192. The 192 results from adding the first two bits from the left, 128 + 64 = 192. These
bits now become 1s and are part of the overall subnet mask. This leaves 6 bits for host IP
addresses or 26 = 64 hosts per subnet.
4th Octet borrowed bits for subnet:

Subnet bit values: (from left side)

128

64

32

16

With this information, the following table can be built. The first two bits are the subnet binary value. The
last 6 bits are the host bits. By borrowing 2 bits from the 8 bits of the host address 4 subnets, 2^2, with
64 hosts each, can be created. The 4 networks created are as follows:

The 200.1.1.0 network

The 200.1.1.64 network

The 200.1.1.128 network

The 200.1.1.192 network

The 200.1.1.0 network is considered unusable, unlesss the networking device supports the IOS
command ip subnet-zero, which allows using the first subnet.
Subnet Bits
Borrowed
Binary
Value

Subnet Bits
Decimal
Value

Host Bits
Possible Binary
Values (Range)
(6 Bits)

Subnet/Host
Decimal
Range

0 Subnet

00

000000111111

063

No

1st Subnet

01

64

000000111111

64127

Yes

2nd Subnet

10

128

000000111111

128191

Yes

3rd Subnet

11

192

000000111111

192254

No

Subnet
No.

Useable?

Notice that the first subnet always starts at 0 and, in this case, increases by 64, which is the number of
hosts on each subnet. One way to determine the number of hosts on each subnet or the start of each
subnet is to take the remaining host bits to the power of 2. Because we borrowed two of the 8 bits for
subnets and have 6 bits left, the number of hosts per subnet is 26 or 64. Another way to figure the
number of hosts per subnet or the increment from one subnet to the next is to subtract the subnet mask
value in decimal, 192 in the fourth octet, from 256, which is the maximum number of possible
combinations of 8 bits. This equals 64. This means start at 0 for the first network and add 64 for each

CS215 Lab #7

additional subnetwork. For example, if the second subnet is used, the 200.1.1.64 network cannot be
used for a host ID since the network ID of the 64 subnet has all zeros in the host portion.
Another common way to represent a subnet mask, is the use of the slash/number (/#) where the #
following the slash is the number of bits used in the mask (network and subnet combined). As an
example, a Class C network address such as 200.1.1.0 with a standard subnet mask (255.255.255.0)
would be written as 200.1.1.0 /24, indicating that 24 bits are used for the mask. The same network,
when subnetted by using two host bits for subnets, would be written as 200.1.1.0 /26. This indicates
that 24 bits are used for the network and 2 bits for the subnet. This would represent a custom subnet
mask of 255.255.255.192 in dotted decimal format.
A Class A network of 10.0.0.0 with a standard mask (255.0.0.0) would be written as 10.0.0.0 /8. If 8 bits
(the next octet) were being used for subnets it would be written as 10.0.0.0 /16. This would represent a
custom subnet mask of 255.255.0.0 in dotted decimal format. The slash number after the network
number is an abbreviated method of indicating the subnet mask being used.

Step 5 Use the following information and the previous examples to answer the following
subnet-related questions
A company has applied for and received a Class C network address of 197.15.22.0. The physical
network is to be divided into 4 subnets, which will be interconnected by routers. At least 25 hosts will be
needed per subnet. A Class C custom subnet mask needs to be used and a router is needed between
the subnets to route packets from one subnet to another. Determine the number of bits that need to be
borrowed from the host portion of the network address and the number of bits that will be left for host
addresses.
Note: There will be 8 possible subnets, of which 6 can be used.
Fill in the following table and answer the following questions:

Subnet No.

Subnet Bits
Borrowed
Binary Value

Subnet Bits
Decimal and
Subnet No.

Host Bits
Possible
Binary
Values
(Range) (5
Bits)

Subnet/Host
Decimal
Range

Use?

0 Subnet

1st Subnet

2nd Subnet

3rd Subnet

4th Subnet

5th Subnet

6th Subnet

7th Subnet

CS215 Lab #7

NOTES:

__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
Use the table just developed to help answer the following questions:
1. Which octet(s) represent the network portion of a Class C IP address? _________________
2. Which octet(s) represent the host portion of a Class C IP address? ____________________
3. What is the binary equivalent of the Class C network address in the scenario? 197.15.22.0
Decimal network address:

___________ ___________ ___________ ___________

Binary network address:

___________ ___________ ___________ ___________

4. How many high-order bits were borrowed from the host bits in the fourth octet? ___________
5. What subnet mask must be used? Show the subnet mask in decimal and binary.
Decimal subnet mask:

___________ ___________ ___________ ___________

Binary subnet mask:

___________ ___________ ___________ ___________

6. What is the maximum number of subnets that can be created with this subnet mask? ________
7. What is the maximum number of useable subnets that can be created with this mask? _______
8. How many bits were left in the fourth octet for host IDs? _____________________________
9. How many hosts per subnet can be defined with this subnet mask? _____________________
10. What is the maximum number of hosts that can be defined for all subnets with this scenario?
Assume the lowest and highest subnet numbers and the lowest and highest host ID on each subnet
cannot be used. _____________________________________________________
11. Is 197.15.22.63 a valid host IP address with this scenario? ___________________________
12. Why or why not? __________________________________________________________
13. Is 197.15.22.160 a valid host IP address with this scenario? ___________________________
14. Why or why not? __________________________________________________________
15. Host A has an IP address of 197.15.22.126. Host B has an IP address of 197.15.22.129. Are these
hosts on the same subnet? _______ Why?

__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________

CS215 Lab #7

Part 2: Subnetting a Class A Network

Objective
Analyze a Class A network address with the number of network bits specified in order to determine the
following:
Subnet mask
Number of subnets
Hosts per subnet
Information about specific subnets

Background / Preparation
This is a written exercise and is to be performed without the aid of an electronic calculator.

Step 1 Given a Class A network address of 10.0.0.0 / 24 answer the following questions
How many bits were borrowed from the host portion of this address? ___________
What is the subnet mask for this network?
1. Dotted decimal ___________________________________________________________
2. Binary

_______________ _______________ _______________ _______________

How many usable subnetworks are there? _________________________________________

How many usable hosts are there per subnet? ______________________________________
What is the host range for usable subnet sixteen? ____________________________________
What is the network address for usable subnet sixteen? ________________________________
What is the broadcast address for usable subnet sixteen? _______________________________
What is the broadcast address for the last usable subnet? _______________________________
What is the broadcast address for the major network? _________________________________

CS215 Lab #7

Part 3: Subnetting a Class B Network

Objective
The objective of this lab is to provide a subnetting scheme using a Class B network

Background / Preparation
This is a written lab and is to be performed without the aid of an electronic calculator.
ABC Manufacturing has acquired a Class B address, 172.16.0.0. The company needs to create a
subnetting scheme to provide the following:

36 subnets with at least 100 hosts

24 subnets with at least 255 hosts

10 subnets with at least 50 hosts

It is not necessary to supply an address for the WAN connection since it is supplied by the Internet
service provider.

Step 1 Given this Class B network address and these requirements answer the following
questions
How many subnets are needed for this network? ______________________________________
What is the minimum number of bits that can be borrowed? ______________________________
What is the subnet mask for this network? __________________________________________
1. Dotted decimal ___________________________________________________________
2. Binary ________________ ________________ ________________ ________________
3. Slash format _____________________________________________________________
How many usable subnetworks are there? __________________________________________
How many usable hosts are there per subnet? _______________________________________

Step 2 Complete the following chart listing the first three subnets and the last 4 subnets
Subnetwork #

Subnetwork ID

Host Range

Broadcast ID

What is the host range for subnet two? ____________________________________________

What is the broadcast address for the 126th subnet? ________________________________
What is the broadcast address for the major network? ________________________________

CS215 Lab #7

Part 3: Subnetting a Class C Network

Objective
The objective of this lab is to provide a subnetting scheme using a Class C network.

Background / Preparation
This is a written exercise and is to be performed without the aid of an electronic calculator.
The Classical Academy has acquired a Class C address, 192.168.1.0. The academy needs to create
subnets to provide low level security and broadcast control on the LAN. It is not necessary to supply an
address for the WAN connection. It is supplied by the Internet service provider.
The LAN consists of the following, each of which will require its own subnet:

Classroom #1 28 nodes

Classroom #2 22 nodes

Computer lab 30 nodes

Instructors 12 nodes

Administration 8 nodes

Step 1 Given this Class C network address and these requirements answer the following
questions
How many subnets are needed for this network? _____________________________________
What is the subnet mask for this network?
1. Dotted decimal ________________________________________________________
2. Binary ________________ ________________ ________________ _______________
3. Slash format _____________________________________________________________
How many usable hosts are there per subnet? ______________________________________

Step 2 Complete the following chart

Subnetwork #

Subnetwork ID

Host Range

Broadcast ID

What is the host range for subnet six? ____________________________________________

What is the broadcast address for the 3rd subnet? ____________________________________
What is the broadcast address for the major network? ________________________________

CS215 Lab #7