Vibrating String-Hyper Physics

Vibrating String
HyperPhysics
http://hyperphysics.phy-astr.gsu.edu/hbase/waves/string.html
Vibrating String
The fundamental vibrational mode of a stretched string is such that the wavelength is twice the
length of the string.
Applying the basic wave relationship gives an expression for the fundamental frequency:
Calculation
Since the wave velocity is given by
, the frequency expression
can be put in the form:
The string will also vibrate at all harmonics of the fundamental. Each of these harmonics will form
a standing wave on the string.
Page 1 of 10
This shows a resonant standing wave on a string. It is driven by a vibrator at 120 Hz.
For strings of finite stiffness, the harmonic frequencies will depart progressively from the
mathematical harmonics. To get the necessary mass for the strings of an electric bass as shown
above, wire is wound around a solid core wire. This allows the addition of mass without producing
excessive stiffness.
Example measurements on a steel string
String frequencies String instruments Illustration with a slinky Mathematical form
Measurements with a steel string

The fundamental frequency of a stetched string is given by
Calculat
ion
Page 2 of 10
A brief data set with a steel string is plotted to check the consistency of the
data with the above equation. Hanging masses provide the tension in the string,
which was adjusted to a vibrating length of 50 cm.
Hanging
Mass
Tensio
n
Frequency
3 kg
29.4 N
98 Hz
4 kg
39.2 N
112 Hz
5 kg
49 N
122.5 Hz
6 kg
58.8 N
131 Hz
This is obviously not an ideal string since the best straight line fit of the
data of frequency vs square root of tension would not pass through zero
frequency at zero tension. If that fact is ignored for the moment and the
average slope of the line through zero is taken, the slope is 17.6 Hz/N 1/2. Using
the frequency relationship above, this corresponds to a mass per unit length m/L
= 57 grams/meter.
String Instruments
Double Bass
Violin
Cello
Electric
Viola
Guitar
Page 3 of 10
Guitar
String
properties
String
excitation
String instrument resonances
The Violin
The violin, the most commonly used
member of the modern string family, is
the highest-sounding instrument of
that group.
The strings are tuned a fifth apart at
G3(196 Hz), D4, A4, E5(659.3 Hz).
Strings characteristically produce a
fundamental resonance plus all the
string harmonics. The sound of the
instrument is enhanced by body
resonances including the air resonance
of the f-holes.
Violin
details
Wave Velocity in String

The velocity of a traveling wave in a stretched string is determined by the tension and the mass per
unit length of the string.
The wave velocity is given by
Show
When the wave relationship is applied to a stretched string, it is seen that resonant standing wave
modes are produced. The lowest frequency mode for a stretched string is called the fundamental, and
its frequency is given by
Page 4 of 10
From
velocity = sqrt ( tension / mass per unit length )
the velocity =
m/s
when the tension =

for a string of length
N=
lb
cm and mass/length =
For such a string, the fundamental frequency would be
gm/m.
Hz.
Any of the highlighted quantities can be calculated by clicking on them. If numerical values are not
entered for any quantity, it will default to a string of 100 cm length tuned to 440 Hz. Default values
will be entered for any quantity which has a zero value. Any quantities may be changed, but you
must then click on the quantity you wish to calculate to reconcile the changes.
Derivation of wave speed
Harmonics
Page 5 of 10
An ideal vibrating string will vibrate with its

fundamental frequency and all harmonics of that
frequency. The position of nodes and antinodes is
just the opposite of those for an open air column.
The fundamental frequency can be calculated from
where
and the harmonics are integer multiples.
Illustration with a slinky
Vibrating String Frequencies

If you pluck your guitar string, you don't have to tell it what pitch to produce - it knows! That is, its
pitch is its resonant frequency, which is determined by the length, mass, and tension of the string.
The pitch varies in different ways with these different parameters, as illustrated by the examples
below:
If you have a string with
starting pitch:
and change* to
100 Hz
the pitch will be
double the length
50 Hz
four times the tension
200 Hz
four times the mass
50 Hz
*with the other parameters reset to their

original values.
Calculation
Page 6 of 10
Some Violin Details

The violin, the most commonly used member of the modern string family, is the
highest-sounding instrument of that group. Its four strings are stretched over a
high arched bridge that permits the playing of one or two strings at a time, as
well as the nearly simultaneous sounding of three or four as chords. The overall
length of the violin averages about 60 cm (23.5 in), whereas the sounding length
of the strings, from bridge to the nut at the end of the fingerboard, is about
32 cm (12.75 in). The instrument is held on the left side of the body, while the
right hand holds the bow. The wider end of the instrument is placed between the
player's left shoulder and chin, while the left hand encircles its neck, the
fingers stopping the strings to produce the various pitches. Sound is produced
by drawing the bow across the strings to make them vibrate, or by plucking the
strings (PIZZICATO).
The range of the violin extends from G, the lowest open string, upward nearly
four octaves. The strings are tuned a fifth apart at G3(196 Hz), D4, A4,
E5(659.3 Hz).
Many consider that violin making reached its pinnacle in the work of Antonio
Stradivari and Guiseppe Guarneri in the 18th century. Although the basic
construction of the violin has been long established, the subtle variations
which make an outstanding violin are the stuff of legend.
Page 7 of 10
The sound
bowed. If
with more
the sound
quality can be changed considerably by the place where the string is

bowed close to the bridge (sul ponticello) then the sound is brighter
harmonic content. If bowed further from the bridge (sul tasto) then
is darker, more mellow with less harmonic content.
Violin
illustration
Violin Construction
The modern violin consists of about seventy
parts. Parts include the belly, the back, the
ribs, inside blocks, inside lining, bass bar,
purfling, finger board, neck, scroll, nut, lower
nut, tailpiece, loop, end button, pegs, strings,
bridge, and the sound post. The body of the
violin is a hollow box which measures about 35.5
cm in length. The back, the neck, the ribs and
the bridge are usually made of maple. The belly,
linings, and the soundpost are usually made of
spruce. Scrupulous care is taken in selecting and
shaping the belly and back. They must be adjusted
to certain frequencies before assembly in order
for the main wood resonance of the instrument to
be of the apppropriate strength and pitch.
Page 8 of 10
Violin Bridge
The action of the violin bridge is essential to the tone of the instrument. It's
shape and function have been developed over centuries. Underneath the treble
side of the bridge (where the E string rests) is the sound post which extends
from the front to the back plate of the instrument. Since this side of the
bridge rests on this post, it is essentially fixed and acts as a pivot for the
rocking motion of the remainder of the bridge. It does however, couple the sound
energy from the top plate to the back plate of the instrument.
Underneath the bass side of the bridge (where the G string rests), a long, thin
wooden strip called the bass bar is attached, almost parallel to the strings.
This bass foot of the bridge is more free to move, and its motion is the point
Page 9 of 10
of transfer of energy from the strings to the top plate of the instrument.
extended bass bar helps it to transfer the energy to a larger area of the
plate. As can be seen from the diagram, the amplitude of motion is larger
the bass strings. This is desirable for balance of loudness, since
sensitivity of the ear drops off a bit toward the lower frequencies of
instrument.
Page 10 of 10
The
top
for
the
the

Vibrating String-Hyper Physics

Uploaded by

Copyright:

Available Formats

Vibrating String-Hyper Physics

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Vibrating String-Hyper Physics

Uploaded by

Copyright:

Available Formats

Vibrating String

Since the wave velocity is given by

, the frequency expression

can be put in the form:

Measurements with a steel string

String instrument resonances

Wave Velocity in String

velocity = sqrt ( tension / mass per unit length )

when the tension =

For such a string, the fundamental frequency would be

An ideal vibrating string will vibrate with its

and the harmonics are integer multiples.

Illustration with a slinky

Vibrating String Frequencies

double the length

four times the tension

four times the mass

*with the other parameters reset to their

Some Violin Details

quality can be changed considerably by the place where the string is

You might also like