BEMT Theory

Analysis of Propellers
Glauert Blade Element Theory

A relatively simple method of predicting the performance of a propeller (as well as fans or
windmills) is the use of Blade Element Theory. In this method the propeller is divided into a
number of independent sections along the length. At each section a force balance is applied
involving 2D section lift and drag with the thrust and torque produced by the section. At the
same time a balance of axial and angular momentum is applied. This produces a set of non-linear
equations that can be solved by iteration for each blade section. The resulting values of section
thrust and torque can be summed to predict the overall performance of the propeller.
The theory does not include secondary effects such as 3-D flow velocities induced on the
propeller by the shed tip vortex or radial components of flow induced by angular acceleration
due to the rotation of the propeller. In comparison with real propeller results this theory will
over-predict thrust and under-predict torque with a resulting increase in theoretical efficiency of
5% to 10% over measured performance. Some of the flow assumptions made also breakdown for
extreme conditions when the flow on the blade becomes stalled or there is a significant
proportion of the propeller blade in windmilling configuration while other parts are still thrust
producing.
The theory has been found very useful for comparative studies such as optimising blade pitch
setting for a given cruise speed or in determining the optimum blade solidity for a propeller.
Given the above limitations it is still the best tool available for getting good first order
predictions of thrust, torque and efficiency for propellers under a large range of operating
conditions.
Blade Element Subdivision
A propeller blade can be subdivided as shown into a discrete number of sections.
For each section the flow can be analysed independently if the assumption is made that for each there
are only axial and angular velocity components and that the induced flow input from other sections is
negligible. Thus at section AA (radius = r) shown above, the flow on the blade would consist of the
following components.
Since the propeller blade will be set at a given geometric pitch angle ( ) the local velocity vector
will create a flow angle of attack on the section. Lift and drag of the section can be calculated
using standard 2-D aerofoil properties. (Note: change of reference line from chord to zero lift
line). The lift and drag components normal to and parallel to the propeller disk can be calculated
so that the contribution to thrust and torque of the compete propeller from this single element can
be found.
The difference in angle between thrust and lift directions is defined as
2. Inflow Factors
A major complexity in applying this theory arises when trying to determine the magnitude of the
two flow components V0 and V2. V0 is roughly equal to the aircraft's forward velocity (Vinf) but
is increased by the propeller's own induced axial flow into a slipstream. V2 is roughly equal to
the blade section's angular speed ( r) but is reduced slightly due to the swirling nature of the
flow induced by the propeller. To calculate V0 and V2 accurately both axial and angular
momentum balances must be applied to predict the induced flow effects on a given blade
element. As shown in the following diagram the induced flow components can be defined as
factors increasing or decreasing the major flow components.
2. Inflow Factors
A major complexity in applying this theory arises when trying to determine the magnitude of the
two flow components V0 and V2. V0 is roughly equal to the aircraft's forward velocity (Vinf) but
is increased by the propeller's own induced axial flow into a slipstream. V2 is roughly equal to
the blade section's angular speed ( r) but is reduced slightly due to the swirling nature of the
flow induced by the propeller. To calculate V0 and V2 accurately both axial and angular
momentum balances must be applied to predict the induced flow effects on a given blade
element. As shown in the following diagram the induced flow components can be defined as
factors increasing or decreasing the major flow components.
Because these final forms of the momentum equation balance still contain the variables for
element thrust and torque, they cannot be used directly to solve for inflow factors.
However there now exists a nonlinear system of equations (1),(2),(3),(4),(5) and (6) containing
the four primary unknown variables T, Q, a, b. So an iterative solution to this system is
possible.
4. Iterative Solution procedure for Blade Element Theory.
The method of solution for the blade element flow will be to start with some initial guess of
inflow factors (a) and (b). Use these to find the flow angle on the blade (equations (3),(4)), then
use blade section properties to estimate the element thrust and torque (equations (1),(2)). With
these approximate values of thrust and torque equations (5) and (6) can be used to give improved
estimates of the inflow factors (a) and (b). This process can be repeated until values for (a) and
(b) have converged to within a specified tolerance.
It should be noted that convergence for this nonlinear system of equations is not guaranteed. It is
usually a simple matter of applying some convergence enhancing techniques (ie CrankNicholson under-relaxation) to get a result when linear aerofoil section properties are used.
When non-linear properties are used, ie including stall effects, then obtaining convergence will
be significantly more difficult.
For the final values of inflow factor (a) and (b) an accurate prediction of element thrust and
torque will be obtained from equations (1) and (2).
5. Propeller Thrust and Torque Coefficients and Efficiency.
The overall propeller thrust and torque will be obtained by summing the results of all the radial
blade element values.
6. Software Implementation of Blade Element Theory

Two programming versions of this propeller analysis technique are available. The first is a
demonstration program which can be used to calculate thrust and torque coefficients and
efficiency for a relatively simple propeller design using standard linearised aerofoil section data.
The blade is assumed to have a constant pitch (p) so that the variation of with radius is
calculated from the standard pitch equation.
p = 2 r tan( ).
Click here to download Program 1: Propel.exe
The second is a MATLAB script file for the implementation of this method. The source code in
this script is by default a simple propeller design with linear properties. However with the
inclusion of your own propeller geometry and section data a more accurate analysis of the
specific propeller design can be obtained.
Click here to download Program 2: Propel.m
Aerodyn

BEMT Theory

Uploaded by

Copyright:

Available Formats

BEMT Theory

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BEMT Theory

Uploaded by

Copyright:

Available Formats

Analysis of Propellers

Glauert Blade Element Theory

6. Software Implementation of Blade Element Theory

You might also like