Scribd Logo
Upload

Welcome to Scribd!

  • 156 views

    Bs 8666 of 2005 Bas Shape Codes

    Uploaded by

    opulithe
    The document discusses dimensional requirements and tolerances for shaped steel reinforcement bars. It specifies that minimum radius and end projection dimensions from Table 2 apply to all shapes. Dimensional tolerances are given and out-of-tolerance shapes should be drawn and coded as 99. Bends should have a minimum straight length of 4 bar diameters between them. Figures 4-6 illustrate dimensioning of acute angles, cranked bars, and bars with multiple bends.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd

    Bs 8666 of 2005 Bas Shape Codes

    Uploaded by

    opulithe
    156 views5 pages
    The document discusses dimensional requirements and tolerances for shaped steel reinforcement bars. It specifies that minimum radius and end projection dimensions from Table 2 apply to all shapes. Dimensional tolerances are given and out-of-tolerance shapes should be drawn and coded as 99. Bends should have a minimum straight length of 4 bar diameters between them. Figures 4-6 illustrate dimensioning of acute angles, cranked bars, and bars with multiple bends.

    Original Description:

    Bs 8666 of 2005 Bas Shape Codes

    Copyright

    © © All Rights Reserved

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document discusses dimensional requirements and tolerances for shaped steel reinforcement bars. It specifies that minimum radius and end projection dimensions from Table 2 apply to all shapes. Dimensional tolerances are given and out-of-tolerance shapes should be drawn and coded as 99. Bends should have a minimum straight length of 4 bar diameters between them. Figures 4-6 illustrate dimensioning of acute angles, cranked bars, and bars with multiple bends.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    156 views5 pages

    Bs 8666 of 2005 Bas Shape Codes

    Uploaded by

    opulithe
    The document discusses dimensional requirements and tolerances for shaped steel reinforcement bars. It specifies that minimum radius and end projection dimensions from Table 2 apply to all shapes. Dimensional tolerances are given and out-of-tolerance shapes should be drawn and coded as 99. Bends should have a minimum straight length of 4 bar diameters between them. Figures 4-6 illustrate dimensioning of acute angles, cranked bars, and bars with multiple bends.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 5

    The values for minimum radius and end projection, r and P respectively, as specified in Table 2, shall apply to all

    shape codes (see 7.6).


    The dimensions in parentheses are the free dimensions. If a shape given in this table is required but a different
    dimension is to allow for the possible deviations, the shape shall be drawn out and given the shape code 99 and the
    free dimension shall be indicated in parentheses.The length of straight between two bends shall be at least 4d, see
    Figure 6. Figure 4, Figure 5 and Figure 6 should be used in the interpretation of ending dimensions.
    Note 1
    The length equations for shape codes 14, 15, 25, 26, 27, 28, 29, 34, 35, 36 and 46 are approximate and where the bend
    angle is greater than 45, the length should be calculated more accurately allowing for the difference between the
    specified overall dimensions and the true length measured along the central axis of the bar. When the bending angles
    approach 90, it is preferable to specify shape code 99 with a fully dimensioned sketch.
    Note 2
    Five bends or more might be impractical within permitted tolerances.
    Note 3
    For shapes with straight and curved lengths (e.g. shape codes 12 13, 22, 33 and 47) the largest practical mandrel size
    for the production
    of a continuous curve is 400 mm. See also Clause 10.
    Note 4
    Stock lengths are available in a limited numer of lengths (e.g. 6m, 12m). Dimension A for shape code 01 should be
    regarded as indicative and used for the purpose of calculating total length. Actual delivery lengths should be by
    agreement with supplier.

    Table 4

    50mm: 15.413kg/m
    16mm: 1.579kg/m

    BAR MASS per linear metre (kg/m) :40mm: 9.864kg/m


    32mm: 6.313kg/m
    25mm: 3.854kg/m
    12mm: 0.888kg/m
    10mm: 0.616kg/m
    8mm: 0.395kg/m

    Excerpts From Section 8 Drawing Forms for Scheduling and Dimensioning

    20mm: 2.466kg/m
    6mm: 0.222kg/m

    Figure 4 Dimensioning of an acute angle


    8.6 If the angle between two portions of the shape
    meeting at a bend is not a right angle, it shall be defined
    by co-ordinates and not by degress of arcs or radians.
    8.7 When dimensioning an acute angle the tangential
    lines shown in Figure 4 shall be used.

    Figure 5 Dimensioning of cranked bars


    8.8 Apart from shape code 98, bars bent in two planes
    shall be sketched isometrically or shown in two
    elevations, using first angle projection. The words bent
    in two planes or isometric sketch shall appear on the
    schedule adjacent to the sketch.
    8.9 The overall offset dimension of a crank shall be
    not less than twice the size of the bar.
    The angled length (see Figure 5) shall be not less
    than:
    a) 10d for bars not exceeding a nominal size of 16mm
    b) 13d for nominal sizes greater than 16mm
    Figure 6 Example of bar with more than one bend
    8.10 For all shapes with two or more bends in the
    same or opposite directions (whether in the same plane
    or not), the overall dimension given on the schedule
    shall always include a minimum straight of 4d between
    the curved portion of the bends, as shown in Figure 6.
    The value of x in Figure 6 shall be not less than the
    following:
    a) 10d for bars not exceeding a nominal size of 16mm
    b) 13d for nominal sizes greater than 16mm
    NOTE: The minimum values of x are expressed in
    terms of the nominal size of the reinforcement. In
    practice, rolling and bending tolerances, and the fact
    that the circumscribing diameter of deformed
    reinforcement may be up to 10% greater than the
    nominal size, should be considered.

    You might also like