12.thermal Properties of Matter

www.sakshieducation.
com
THERMAL PROPERTIES OF MATTER
Important Points:
1. Heat is a form of energy which has capacity to do the work.

Unit:
SI - Joule
C. G. S - Calorie
1 cal = 4.2 J
2.
Temperature is degree of hotness or coldness in a body which determines direction of

flow of heat.
3.
4.
F 32 C 0 K 273
=
=
180
100
100
Co-Efficient of linear Expansion:

The ratio of increase in length of a metal rod per rise in temperature to its original length is
called linear co-efficient of expansion ( ).
5.
(l 2 l 1 )
l1 (t2 t1 )
/ 0C.
Co-Efficient of Areal Expansion:

The ratio of increase in area of metal plate per rise in temperature to its original area is called
co-efficient of Areal expansion ( ).
6.
(a 2 a 1 )
a1 (t2 t1 )
/ 0C.
Co-Efficient Volume Expansion:

The ratio of increase in volume of metal cube per rise in temperature to its original volume is
called co-efficient of volume expansion ( ).
www.sakshieducation.com
=
7.
( V2 V1 ) / 0C.
V1 ( t 2 t1 )
Relation Between . and

: : = 1: 2 : 3
8.
Variation of Density of with Temperature:

As temperature increases, density decreases.
d0 = dt (1 + t)
d0 and dt are densities at 00C and t0C respectively.
Co-efficient of volume expansion
9.
Platinum is used to seal with glass due to same co-efficient of linear expansion.
10.
If two rods of different materials have the same difference between their lengths (X) at all
temperatures.
l11 = l2 2
l1 =
11.
X 2
X 1
, l2 =
1 ~ 2
1 ~ 2
Invar steel (steel + nickel) has very low . So it is used in making pendulum clocks,
balancing wheels and measuring tapes.
12. Linear and a real expansion have no significance for a liquid since shape of liquid depends on
shape of vessel.
13. Anomalous Expansion of Water:
When water at 0C is heated, its volume decreases up to 4C and from 4C its
volume increases with the increase of temperature. This peculiar behavior of water is
called anomalous expansion of water.
14. Water has maximum density and minimum volume at 4C (or) 277 K
15. Anomalous expansion of water can be demonstrated with Hopes apparatus (or) Dilatometer.
16. Volume Co-Efficient of a Gas ( ):
The ratio of increase in volume of a gas per degree rise of the temperature to the volume at
00C at constant pressure is called Volume Coefficient
=
vt v0
v v
Or = 2 1
v0t
v1t2 v2t1
17. Pressure Co-Efficient of a Gas ( ) :

The ratio of increase in pressure of a gas per degree rise of temperature to its pressure at 00C
at constant volume is called Pressure Co-Efficient.
=
pt p0
p p
Or = 2 1 .
p0t
p1t2 p2t1
18. Relation Between and

For all gases = =
1
= 0.00367 / 0 C
273.15
19. Boyles Law:

At constant temperature, the pressure of a given mass of a gas is inversely proportional to its
volume.
P
1
or PV = k (T = constant)
V
At high temperature and low pressure gases obey Boyles law.

20. Charless -I Law:
At constant pressure, the volume of a given mass of gas is proportional to absolute
temperature.
V
V V
= constant 1 = 2
T
T1 T2
21. Charless -II Law:
At constant volume, the pressure of a given mass of a gas is directly proportional to its
absolute temperature.
P1 P2
P
= constant ( or )
=
T
T1 T 2
22. Real Gas:

The gas which obeys gas laws at high temperature and low pressure is called a Real Gas.
23. Ideal gas Equations:
PV
=R
T
Where P is the pressure, V is the volume of 1gram mole of a gas, T is the absolute temperature
and R is the universal gas constant.
R = 8.31 Joule /gm/K = 2 cal/gm/mole/K
24.
From gas equation
PV
PV
1 1
= 2 2
T1
T2
25. Boltzmanns Constant:

K = 1.38 x 10-23 J/K and K = K =
R
N
Where N = 6.02 x 1023 molecules per mole. N is the Avogadros number.

26. Absolute Zero:
It is the temperature at which the volume of a gas becomes zero at constant pressure (or)
pressure becomes zero at constant volume.
27. Specific Heat:
The quantity of heat required to rise the temperature of unit mass of a substance through 10 C is
called Specific Heat c
c=
Units:
1 dQ
.
m dt
S.I.: J kg K
C. G. S:
Cal
gm
Dimensional formula: L2T 2 K 1

28. Latent Heat:
The amount of heat required by unit mass of a substance to change its state at constant
temperature is called Latent Heat (L)
Q=mL
Units
: S.I.: J/kg
C. G. S
: cal/ gm
Dimensional formula L2T 2

29. Latent heat of fusion of Ice:
The quantity of heat required to change the state of 1gram of ice into water at is called
Latent Heat of Fusion of Ice.
Lice = 80cal / gm
Lice = 0.336 106 J / kg
30. Latent heat of Steam:

The quantity of heat required to change the state of 1gram of water into steam at 1000 C is
called Latent Heat of Steam.
Lsteam = 540cal / gm
Lsteam = 2.268 106 J / kg
31. Co-Efficient of Thermal Conductivity:
a) At steady state the quantity of heat Q flowing through a metal rod of l length and crosssection A in a time t when its ends are at temperature 1 and 2 (1 > 2 ) is given by
Q=
KA ( 1 2 )
t
l
Where K is coefficient of thermal conductivity

b) K depends on the nature of the metal.
c)
It is defined as the rate of flow of heat per unit area and per unit temperature
gradient in steady state.
d)
Junction Temperature:
In steady state,
( K11 + K 2 2 )
( K1 + K 2 )
32. Thermal Resistance:

Thermal resistance R of a conductor of length, cross-section A and conductivity K is given by
R=
l
KA
33. Radiation:
The process of transfer of heat that takes place without the help of the intervening medium is
called Radiation.
Ex. Heat received by the earth from the sun.
34. Black Body:
A body completely absorbing the radiation of all wavelengths falling on it is called a black
body.
35. Emissive Power:
a) The amount of energy emitted per second per unit surface area of a body at a given
temperature for a given wavelength range is called emissive power.
b) At a given temperature if the radiations emitted have a wave length difference, then the
emissive power is equal to e d .
c) Unit -Wm-2
D.F. - MT-3
36. Emissivity (e):
a) The ratio of radiant energy emitted by a surface to radiant energy emitted by a black
body under same conditions is called Emissivity.
b) For a perfect black body emissivity e = 1.
37. Absorptive Power (a ) :
a) At a given temperature, for a given wavelength range, the ratio of energy absorbed to the
energy incident on the body is absorptive power.
a =
Amount of radiant energy absorbed

Amount of radiant energy incident
b) For a perfect black body, the absorptive power, a = 1 .

38. Prevost theory of heat Exchange:
a) Every object emits and absorbs radiant energy at all temperatures except at absolute zero.
b) The rate of emission increases with the increase in the temperature of the body.
c) If the body emits more radiant energy. Than absorbed, its temperature decreases.
d) If the body absorbs more radiant energy than it emits, its temperature increases.
39. Kirchhoffs Laws:
a) At a given temperature, for a given wave length range, the ratio of emissive power to
absorptive power of a substance is constant.
b) This constant is equal to the emissive power of a perfect black body at the given
temperature and wavelength.
i.e.
e
=const = E ,
a
Where E is the emissive power of perfect black body. e And a are emissive and
absorptive powers of a given substance respectively.
c) Good absorbers are good emitters.
40. Stefans Law:
The amount of heat radiated by a black body per second per unit area is directly proportional
to the fourth power of its absolute temperature.
E T4 E = T4.
Where
= Stefans constant
= 5.67 108Wm 2 K 4
41. Stefan - Boltzmanns Law:
a) If a black body at absolute temperature T is surrounded by an enclosure at absolute
temperature To , then the rate of loss of heat energy by radiation per unit area is given by.
E = (T 4 T0 4 )
b) For any hot body, E = Ae(T 4 T0 4 )

Where e is the emissive power and A is the area of cross-section of the hot body
42. Newtons Law of Cooling:
The rate of cooling of a hot body is directly proportional to the excess mean of temperature
of the body above the surroundings, when the difference in temperature of the body and
that of surroundings is small.
d 1 + 2
0
dt 2
1 , 2 are the initial and final temperatures of the body respectively. 0 is temperature of
surroundings .
Very Short Answer Questions
1.
Distinguish between heat and temperature?
A.
Heat
Temperature
1) Heat is a form of energy.
1) It is the degree of hotness or coldness

contained in a body.
2) Heat is the source.
2) Temperature is the effect
3) Unit of heat energy is Joule
3) Unit of temperature is centigrade.
2.
What are the lower and upper fixed points of Celsius and Fahrenheit scale?
A.
Celsius Scale:
Lower fixed point: 00C
Upper fixed point: 1000C
Fahrenheit scale:
3.
Lower fixed point:
320F
Upper fixed point:
2120F
Do the values of coefficients of expansion differ, when the temperatures are measured on
Centigrade scale or on Fahrenheit scale?
A.
4.
Yes.
C F 32
=
5
9
Can a substance contract on heating? Give an example?
A. Yes, Lead, cast iron, pure water when heated from, rubber etc. contract on heating.
5.
Why gap are left between rails on a railway track?
A.
A gap should be left between two successive rails to allow for linear expansion of the rails in
summer.
6.
Why do liquids have no linear and areal Expansions?
A.
Liquids do not have a specific size or shape. The shape of a liquid depends on the shape of
the container. Hence the liquids do not have linear and areal expansions.
7.
What is latent of heat of fusion?
A.
Latent of heat of Fusion:

At constant temperature, the quantity of heat required to change unit mass of substance from
solid state to liquid state is called latent heat of fusion.
8.
What is latent heat of Vaporization?
A.
Latent heat of Vaporization:

The amount of heat required to change unit mass of liquid into vapor at constant temperature
is called latent heat of vaporization.
9.
What is specific gas constant? Is it same for all Gases?
A.
i) For 1 gm of a gas
PV
=r.
T
For m grams of the gas
PV
= mr r is the specific gas
T
constant. ii) The specific gas constant is different for different gases.
10. What are the units and dimensions of specific gas constant?
A.
Units:
J Kg-1 K-1
Dimensions: M0 L2T-2K-1
11.
A.
Why utensils are coated black? Why the bottoms of the utensils are made of Copper?
i) Black surface is a good absorber and good emitter. Hence utensils are coated black.
ii) Copper is a good conductor of heat .Hence copper is used at the bottom of cooking utensils.
12. State weins displacement Law.
A.
The wavelength m corresponding to maximum energy emitted by a black body is inversely

proportional to its absolute temperature.
T=constant.
m
The value of constant is 2.9x10-3 mK.This is called weins displacement law.

13. Ventilators provided in rooms just below the roof. Why?
A.
Ventilators are placed below the roof in rooms to allow hot air to escape.
14. Does a body radiate heat at 0 K? Does it radiate heat at 00C?

A.
i) A body does not radiate heat at 0 K.

ii) A body can radiate heat at 00C.
15. State the different modes of transmission of heat. Which of these modes require medium?
A.
Heat is transferred or propagated by three distinct processes namely conduction, convection

and radiation.
Conduction and convection require medium.
16. Define coefficient of thermal conductivity and temperature gradient?

A.
Thermal Conductivity:
It is the quantity of heat flowing normally per unit time through unit area of the substance per
unit temperature gradient.
K=
Qd
A(2 1 )t

If A = 1m2, 2 1 =10 c/m and t = 1s, then K = Q
d
Temperature Gradient:
Temperature difference per unit length is called temperature gradient.
Temperature gradient =
2 1 0
c/m
d
17. What is thermal resistance of a conductor? On factors does it depend?
A.
Thermal resistance (R):

The thermal resistance of a body is a measure of its opposition to the flow of heat through it.
It is defined as the ratio of temperature difference to the heat current.
R=
l
KA
Thermal resistance of a body depends on length and area of cross-section of the conductor.
18.
State the units and dimensions of Coefficient of Convection?
A.
Units
Wm2 K 1
Dimensions :
MT 3 K 1
19.
Define emissive power and emissivity.
A.
Emissive power ( e ):
i) The amount of energy emitted per second per unit surface area of a body at a given
Temperature for a given wavelength range ( and +d ) is called emissive power.
ii) At a given temperature if the radiations emitted have a wavelength difference d , then the
Emissive power is equal to e d .
iii) S.I unit of emissive power is Wm-2 and its dimensional formula is MT-3.
Emissivity (e): The ratio of radiant energy emitted by a surface to radiant energy emitted by
a black body under same conditions is called emissivity.
i)
For a perfect black body emissivity e=1.
20. What is Green House Effect? Explain Global Warming?

A.
The surface of the earth and atmosphere gets heated up due to absorption of radiation from
sun by green house gases, namely Carbon dioxide, Methane, Nitrous oxide, etc. This is known
as green house effect.
Hence the earth becomes warmer and the average temperature of the earth increases. This is
known as global warming. This global warming may cause problem for human life, plants
and animals. Because of global warming, ice caps are melting faster, sea level is rising and
weather pattern is changing.
21. Define absorptive power of a body. What is the absorptive power of a perfect black body?
A.
Absorptive Power ( a ):
i) At a given temperature, for a given wavelength range, the ratio of energy absorbed to the
energy incident on the body is absorptive power.
ii)
For a perfect black body, the absorptive power, a =1.
22. State Newtons Law of Cooling?

A.
Newton's Law of Cooling:

The rate of fall of temperature of a body is proportional to the excess mean temperature of
the body over the surroundings.
If a body cools from a temperature 1 to the temperature 2 in the surroundings at a 0
temperature, then
d 1 + 2
0
dt 2
23.
A.
State the conditions under which Newton's law of cooling is applicable?

Conditions: Newtons law of cooling is applicable when
(i) Heat lost by the body is mainly by convection.
(ii) The hot body is cooled in uniformly stream lined flow of air or forced convection.
(iii) The temperature of every part of the body is same.
24.
The roof buildings are often painted white during summer. Why?
A.
The roof buildings are often painted white during summer, because white is a poor absorber.
Short Answer Questions
1.
Explain Celsius and Fahrenheit scales of temperature. Obtain the relation between
Celsius and Fahrenheit scales of temperature.
A.
Celsius scale of temperature:

In the centigrade scale, the lower fixed point (ice point) is 00C and the upper fixed point
(steam point) is 1000C. The difference between two fixed point values is 1000C. The interval
between these two points is divided into 100 equal parts and each corresponds to 10C on the
scale.
Fahrenheit scales of Temperature:
In the Fahrenheit scale, the lower fixed point is 320F and upper fixed point is taken as 2120F .
The difference between two fixed point values is 1800F. The interval between these two points
is divided into 180 equal parts then each part corresponds to 10F on the scale.
Relation between Celsius and Fahrenheit scales:
The temperature difference between the ice and stream points should be the same on Celsius
and Fahrenheit scales.
In the centigrade scale, the lower fixed point (ice point) is 00C and the upper fixed point
(steam point) is 1000C.
In the Fahrenheit scale, the lower fixed point is 320F and upper fixed point is taken as 2120F .
The difference between two fixed point values is 1800F.
Let the temperature of a body on Celsius and Fahrenheit scales be C and F respectively.
Then,
2.
C -0 F 32
=
100
180
C F 32
=
5
9
Two identical rectangular strips one of copper and the other of steel are riveted together
to form a bimetallic strip. What will happen on heating?
A.
Bimetallic Strip:
A bimetallic strip consists of strips made of two different metals of different coefficients of
expansion, riveted together. When heated, it bends such that the strip with more expansion
(copper) lies on the convex side.
Uses:
A bimetallic strip is used
(i) For continuous recording temperature
(ii) As a thermostat to control the temperature of a body
(iii) As a fire alarm.
3.
Pendulum clocks generally go fast in winter and slow in summer. Why?
A.
T = 2
l
or T
g
Time period of a pendulum clock is directly proportional to square root of the length of the
Pendulum.
i) In winter the length of the pendulum decreases and its time period decreases. So clock goes
fast.
ii) In summer the length of the Pendulum increases and its time period increases. So the clock
goes slow.
4.
A.
In what way is the anomalous behavior of water advantageous to aquatic animals?

In cold countries, at nights as temperature decreases, the upper layers of the lake contract and
sink to the bottom. This process goes on until the temperature of water becomes 40C. When
the top layer cools further it does not sink to the bottom. With further cooling the top layers
gradually form ice at the top. This results in water at the bottom at 40C, so that aquatic life
can live in a pond.
5.
Explain conduction, convection and radiation with Examples?
A.
Conduction:
The process of transfer of heat that takes place without the movement of the particles of the
medium is called conduction.
Ex. Heating up of a metal rod
Convection:
The process of transfer of heat with the bodily movement of the particles of the medium is
called convection.
Ex. Heating up of a liquid
Radiation:
The process of transfer of heat that takes place without the help of the intervening medium is
called radiation.
Ex. Heat received by the earth from the sun.
Long Answer Questions
1.
State Boyles law and Charles law. Hence derive ideal gas equation. Which of the two
laws is better for the purpose of thermometry and why?
A.
Boyles Law:
At constant temperature, the pressure (P) of a given mass of a gas is inversely proportional to
its volume (V).
1
V
Or
PV = constant
Charles Law at Constant Pressure:

At constant Pressure, the volume (V) of given mass of gas is directly proportional to its
absolute temperature (T).
V T
Or
V / T = constant
Charles Law at Constant Volume:

At constant volume, the pressure (P) of a given mass of a gas is directly proportional to its
absolute temperature (T).
P T Or
P
= Constant
T
Ideal Gas Equation:

Consider a gas of volume; pressure and temperature are V1, P1 and T1 respectively. Let these
values are changed to V2, P2 and T2 in two different stages PV
.
1 1 = PV
2
i) Keeping the temperature T1 constant, the pressure of the gas is changed from P1
to P2. Then let its volume changes from V1 to V.
From Boyles law,
V =
PV
1 1
P2
.......................... (1)
ii) Now Keeping pressure P2 constant, the temperature of the gas is changed from T1 to
T2.Then let its volume changes from V1 to V2.
From Charles law
V V2
= ,
T1 T2
V =
V2T1
............................. (2)
T2
From equations (1) and (2)

Or
PV
VT
PV PV
PV
1 1
= 2 1 1 1= 2 2
=r
P2
T2
T1
T2
T
The constant r is called specific gas constant which is different for different gases. For one
mole of gas,
PV = RT
this is called ideal gas equation.
Here R is called universal gas constant. R = 8.314 J mole-1 k-1

For n moles of gas,
PV = nRT
Gas Thermometers:
Charles law is better for the purpose of measurement of temperature because in Boyles law
temperature is constant.
2.
Explain thermal conductivity and coefficient of thermal conductivity.

A copper bar of thermal conductivity 401W/(mK) has one end at 1040 C and the other at
240 C. The length of the bar is 0.10m and the cross sectional area is 1.0 106 m2 . What is
the rate of heat conduction along the bar?
A.
Thermal Conductivity:
Definition:
The ability of a solid to conduct heat is called thermal conductivity.
Explanation:
When one end of a metal rod is heated, the amplitude of vibration of the atoms at that end
increases. These atoms collide with the adjacent atoms by sharing their energy with them.
Thus heat energy flows from higher temperature end to lower temperature end of the rod.
Coefficient of Thermal Conductivity (K):
The amount of heat (Q) flowing through a rod is directly proportional to
i. The area of cross section (A) of the rod
ii. Temperature difference ( 2 1 ) between the ends of the rod
iii. The time (t) of flow the heat through the rod and
iv. is inversely proportional to the length ( l ) of the rod.
Where K is called the co-efficient of thermal conductivity of the rod
Definition of K:
K =
Q /t
A( 1 2 )/ l
If A = 1 and
( 1 2 )
Q
=1 , then K =
l
t
It is defined as the quantity of heat flowing normally per second through unit area of crosssection of the rod per unit temperature gradient.
Problem:
K = 401 w/mk ; L = 0.1 m ; A = 1 10-6 m2 ; 2 1 = 104 - 24 = 80C
Q
Rate of heat conduction (P) = =
t R
Where R = thermal resistance of Cu =

P=
3.
L
K cu A
0.1
= 249.3
401x106
80
=
= 0.32 W
R 249.3
State and explain Newton's Law of cooling. State the conditions under which Newton's
Law of cooling is applicable.
A body cools down from 60C to 50C in 5 minutes and to 40C in another 8 minutes.
Find the temperature of the surroundings.
A.
Newton's Law of Cooling:

The rate of fall of temperature of a body is proportional to the difference between the mean
temperature of the body and the temperature of the surroundings
Explanation:
Let a body cools from a temperature 2 to 0 the temperature .Let be the temperature of
the surroundings. Then the rate of fall of temperature of the body
d
is given by
dt
d 1 + 2
0
dt 2
Or
d
+ 2
=K 1
0
dt
2
Where K is a positive constant that depends on area and the nature of the surface of the
body
The amount of heat lot is given by Q = ms
Or
dQ
d
= ms
dt
dt
d
1 d
d
1
=
(or ) = A (T 4 T04 )
dt ms dt
dt ms
Conditions:
Newtons law of cooling is applicable when (i) the heat lost by conduction is negligible and
heat lost by the body is mainly by convection (ii) the hot body is cooled in uniformly stream
lined flow of air or forced convection (iii) the temperature of every part of the body is same.
Problem:
From Newtons law of cooling,
( 60 50 ) 60 + 50
5
Dividing,
and
50 40 50 + 40

8
2
= 28.34C
Problems
1.
What is the temperature for which the readings on Kelvin and Fahrenheit scales are
same?
A:
K 273.15 F 32
=
100
180
Here K = F
F 273.15 F 32
=
100
180
F = 574.60 C
2.
Find the increase in temperature of aluminum rod if its length is to be increased by

1 %.( for aluminum= 25 106 / 0 C ).
A:
l2 l1
l l
( t2 t1 ) = 2 1
l1 ( t2 t1 )
l1
Percentage increase in length = 25 106 1 100
1 = 25 106 ( t2 t1 ) 100
( t2 t1 ) =
3.
1
1
= 400o C.
6
25 10
100
The mass of a litre of a gas is 1.562g at 0o C under a pressure of 76cm of Mercury.

The temperature is increased to 250o C and the pressure to 78cm of mercury. What is
the mass of one litre of the gas under new conditions?
A:
P1 = 76cm of mercury;
P2 = 76cm of mercury; T1 = 273K ;
T2 = 273 + 250 = 523K ; 1 = 1.562 g / litre
P1
P
= 2
1T1 2T2
2 =
4.
P2T1 1 78 273 1.562

=
= 0.8366 g
PT
76 523
1 2
The volume of a mass of gas at 37C and a pressure of 75cm of mercury is 620 c.c. Find
the volume at N.T.P
A:
At NTP, P1 = 76cm ; T1 = 273K

PV
PV
1 1
= 2 2
T1
T2
Or
5.
75 620 76 V
=
V = 538.8 C.C
310
273
How much steam at 1000 C is to be passed into water of mass 100g at 200 C to raise its
temperature by 50 C ? (Latent heat of steam is 540 cal/g and specific heat of water is
1cal / g 0C )
A:
t2 = 1000 C , m1 = 100 g , t1 = 200 C , t3 = t1 + 5 = 20 + 5 = 250 C
L = 540 cal/gm, S = 1cal / g 0C

Heat gained by cold body = heat lost by hot body
If m is the mass of vapour to be added m1s(t3 t1 ) = m( L + s t2 t3 )
100 1 (25 20) = m(540 + 1 (100 25))
500 = m (615)
m=
6.
500
= 0.813 gm
615
2kg of air is heated at constant volume. The temperature of air is increased from 293K to
313K. If the specific heat of air at constant volume is 0.718kJ/kg K, find the amount of
heat absorbed in kJ and kcal. (J = 4.2 kJ/kcal)
A:
m = 2kg, T1 = 273K , T2 = 313K

Cv = 0.719 KJ / Kg K , J = 4.2 KJ / Kcal
Q = mCv (T2 T1 ) = 2 0.718 (313 273) = 28.72kJ
=
7.
28.72
= 6.838 K cal
4.2
A clock, with a brass pendulum, keeps correct time at 200C, but loses 8.212 s per day,
when the temperature rises to 300C. Calculate the coefficient of linear expansion of
brass?
A:
Loss of time for one day =
1
1
( t2 t1 ) 86400 8.212 = 10 86400
2
2
= 19 106 / 0 C
8.
If the volume of nitrogen of mass 14kg is 0.4m3 at 300 C . Calculate the pressure?
A:
Mass of the gas = m = 14kg = 14 x 103 gm

Molecular weight of nitrogen (M) = 28
V = 0.4m3 , T = 30 + 273 = 303K
PV = nRT PV =
P=
9.
m
RT
M
mRT 14 103 8.317 303

=
= 31.5 105 N / m 2
MV
28 0.4
A body cools from 60C to 40C in 7 minutes and what will be its temperature
after next 7 minutes, if the temperature of its surroundings is 10C?
A.
From Newtons law of cooling,
( 60 40 ) 60 + 40 10 and 40 40 +
7
Dividing and solving,
= 28 C
10
10.
If the maximum intensity of radiation for a black body is found at 2.65 m,

what is the temperature of the radiating body?
(Wiens constant = 2.90 10-3 mK)
A.
max = 2.65 m = 2.6510-6 m.
But, max T = constant = 2.90 10-3 mK.

T=
2.90 103
max
2.90 103
=
= 1094 K
2.65 106

12.thermal Properties of Matter

Uploaded by

Copyright:

Available Formats

12.thermal Properties of Matter

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

12.thermal Properties of Matter

Uploaded by

Copyright:

Available Formats

www.sakshieducation.

THERMAL PROPERTIES OF MATTER

1. Heat is a form of energy which has capacity to do the work.

Temperature is degree of hotness or coldness in a body which determines direction of

Co-Efficient of linear Expansion:

Co-Efficient of Areal Expansion:

Co-Efficient Volume Expansion:

Relation Between . and

Variation of Density of with Temperature:

17. Pressure Co-Efficient of a Gas ( ) :

18. Relation Between and

19. Boyles Law:

At high temperature and low pressure gases obey Boyles law.

22. Real Gas:

From gas equation

25. Boltzmanns Constant:

Where N = 6.02 x 1023 molecules per mole. N is the Avogadros number.

Dimensional formula: L2T 2 K 1

Dimensional formula L2T 2

Lice = 0.336 106 J / kg

30. Latent heat of Steam:

Lsteam = 2.268 106 J / kg

Where K is coefficient of thermal conductivity

32. Thermal Resistance:

Amount of radiant energy absorbed

b) For a perfect black body, the absorptive power, a = 1 .

b) For any hot body, E = Ae(T 4 T0 4 )

Distinguish between heat and temperature?

1) Heat is a form of energy.

1) It is the degree of hotness or coldness

2) Heat is the source.

2) Temperature is the effect

3) Unit of heat energy is Joule

3) Unit of temperature is centigrade.

Lower fixed point:

Upper fixed point:

Can a substance contract on heating? Give an example?

Why gap are left between rails on a railway track?

Why do liquids have no linear and areal Expansions?

What is latent of heat of fusion?

Latent of heat of Fusion:

What is latent heat of Vaporization?

Latent heat of Vaporization:

What is specific gas constant? Is it same for all Gases?

For m grams of the gas

The wavelength m corresponding to maximum energy emitted by a black body is inversely

The value of constant is 2.9x10-3 mK.This is called weins displacement law.

14. Does a body radiate heat at 0 K? Does it radiate heat at 00C?

i) A body does not radiate heat at 0 K.

Heat is transferred or propagated by three distinct processes namely conduction, convection

16. Define coefficient of thermal conductivity and temperature gradient?

17. What is thermal resistance of a conductor? On factors does it depend?

Thermal resistance (R):

State the units and dimensions of Coefficient of Convection?

Define emissive power and emissivity.

For a perfect black body emissivity e=1.

20. What is Green House Effect? Explain Global Warming?

For a perfect black body, the absorptive power, a =1.