Scribd Logo
Upload

Welcome to Scribd!

  • 190 views

    BHEL Specification Sheet TDC.0.304 Rev01

    Uploaded by

    Naresh Goud
    This document outlines the technical delivery conditions for cold drawn coiled sheets according to ASTM B575 UNS N10276. It specifies requirements for chemical composition, dimensions, mechanical properties, identification marking, packaging, inspection, and intended end use. Sheets must be cold drawn with a minimum 20% thickness reduction. Dimensional tolerances for thickness, width, flatness, waves and camber are defined. Coils must be identified with tags and stickers listing heat number, size, weight, length, and manufacturer. Each coil will be wrapped, packed in a wooden box, and certified with test results to ensure conformance to the specification. The intended end use is for manufacturing flexible seals for gates and dampers.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    BHEL Specification Sheet TDC.0.304 Rev01

    Uploaded by

    Naresh Goud
    190 views2 pages
    This document outlines the technical delivery conditions for cold drawn coiled sheets according to ASTM B575 UNS N10276. It specifies requirements for chemical composition, dimensions, mechanical properties, identification marking, packaging, inspection, and intended end use. Sheets must be cold drawn with a minimum 20% thickness reduction. Dimensional tolerances for thickness, width, flatness, waves and camber are defined. Coils must be identified with tags and stickers listing heat number, size, weight, length, and manufacturer. Each coil will be wrapped, packed in a wooden box, and certified with test results to ensure conformance to the specification. The intended end use is for manufacturing flexible seals for gates and dampers.

    Original Description:

    BHEL's specification sheet Hastelloy C 276

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document outlines the technical delivery conditions for cold drawn coiled sheets according to ASTM B575 UNS N10276. It specifies requirements for chemical composition, dimensions, mechanical properties, identification marking, packaging, inspection, and intended end use. Sheets must be cold drawn with a minimum 20% thickness reduction. Dimensional tolerances for thickness, width, flatness, waves and camber are defined. Coils must be identified with tags and stickers listing heat number, size, weight, length, and manufacturer. Each coil will be wrapped, packed in a wooden box, and certified with test results to ensure conformance to the specification. The intended end use is for manufacturing flexible seals for gates and dampers.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    190 views2 pages

    BHEL Specification Sheet TDC.0.304 Rev01

    Uploaded by

    Naresh Goud
    This document outlines the technical delivery conditions for cold drawn coiled sheets according to ASTM B575 UNS N10276. It specifies requirements for chemical composition, dimensions, mechanical properties, identification marking, packaging, inspection, and intended end use. Sheets must be cold drawn with a minimum 20% thickness reduction. Dimensional tolerances for thickness, width, flatness, waves and camber are defined. Coils must be identified with tags and stickers listing heat number, size, weight, length, and manufacturer. Each coil will be wrapped, packed in a wooden box, and certified with test results to ensure conformance to the specification. The intended end use is for manufacturing flexible seals for gates and dampers.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Technical Delivery Condition (TDC)

    For
    Cold Drawn coiled sheets to specification
    ASTM B575 UNS N 10276

    Ranipet

    Doc Ref:

    TDC: O : 304

    Rev.No.

    01

    Date:

    08 06 2010

    Page No

    Page 1 of 2

    1.0 Scope
    1.1

    This TDC specifies the additional requirements for the delivery of cold drawn sheets
    conforming to ASTM B 575 UNS N10276 to the latest edition.

    1.2

    The size and Quantity shall be as specified in the Enquiry / purchase order.

    2.0 Chemical composition and process


    2.1

    The material shall be made by any one of the process allowed in the specification
    and chemical composition shall comply with the specification requirements.

    2.2

    Final sheet thickness shall be made by cold drawing with minimum reduction of
    thickness of about 20% for getting required stiffness.

    3.0 Dimensional tolerances


    3.1

    The supply of sheets is in coil form, the following tolerance shall apply.
    a) Thickness

    As per Enquiry / PO

    b) Thickness tolerance

    As per ASTM B 906 Table I

    c) Width

    Plus 0.5mm , minus 0 mm

    d) Flatness

    1mm /Meter (Max) ,when uncoiled and stretched

    e) No. of waves

    3 per meter (max)

    f) Camber

    Maximum 3mm for

    g) Coil ID

    200mm (minimum) to 250 mm (maximum)

    h) Coil OD

    400mm maximum

    i)

    50 KGs, +/- 5 KGs

    Coil weight

    2 meter length

    4.0

    Heat treatment

    4.1

    The sheets will be supplied in cold drawn condition without any heat treatment

    5.0

    Mechanical Test

    5.1

    Testing shall be done for each melt as per ASTM E8 and


    given below

    acceptance norms are

    a) Ultimate tensile strength

    182000Psi/1255 Mpa (Max)

    b) Hardness on finished sheet

    330 to 380VHN

    6.0

    Freedom from defects

    6.1

    All sheets shall be free from harmful defective like cracks, lamination, Scarabs, Etc
    The surface shall be free from scales , rust, pitting, wrinkles

    6.2

    Repair on finished coil is prohibited.

    7.0

    Finish

    7.1

    The edges of coils shall be slit without fish tails and kinks. The coils should
    contain any weld seam

    Record of
    revision

    not

    Rev 00/ DTD 01 04 94

    Original Issue

    Rev 01 /08 06 2010

    TDC requirements are reviewed fully in consultation with


    Engineering ,MPL , purchase, QA and QC (proc.). correction in
    Clause 3.1, 5.1, 8.1 and in other clauses
    minor editorial
    correction done .

    Technical Delivery Condition (TDC)


    For
    Cold Drawn coiled sheets to specification
    ASTM B575 UNS N 10276

    Ranipet

    Doc Ref:

    TDC: O : 304

    Rev.No.

    01

    Date:

    08 06 2010

    Page No

    Page 2 of 2

    8.0

    Marking

    8.1

    Each coil shall be identified by Tag and also permanent stickers at ID and OD of the
    coil .The details shall be as given below
    a) Coil number
    b) Specification
    c) Size (Thickness x Width )
    d) Heat number
    e) Weight of coil in KGs
    f) Length of coil in Meter
    g) PO Number
    h) Manufacturers identification.

    9.0

    Packing and Dispatch

    9.1

    It is the responsibility
    transit

    9.2

    Each coil shall be rigidly wrapped with gum tape so as to cover the entire coil and
    packed in polythene cover.

    9.3

    Coils shall be packed in a wooden box as per ASTM A700 Fig. No 78 .

    10.0

    Inspection and certification

    10.1

    All tests shall be complied as per the specification for each heat and the same shall
    be submitted along with supply.

    10.2

    The test certificates shall be furnish the following details legibly in English language
    only
    a) BHEL Purchase order number
    b) Test certificate number

    of the supplier

    to ensure that no damage

    occurs during

    c) Specification and Grade with applicable year of code


    d) PO Quantity and size
    e)
    f)
    g)
    h)
    i)

    Melt number
    Chemistry (Melt wise)
    Mechanical test results UTS and Hardness
    Coil number and weight
    Process of manufacturing with amount of cold reduction

    12.0

    End use

    12.1

    The coils are intended for manufacturing flexible seals for Gates and Dampers for
    the purpose of isolation of Hot/Cold Air / flue gas.

    Prepared by

    Reviewed by
    Engineering (GD)
    Purchase
    MPL
    QC/proc.
    QA

    Issued by

    QUALITY ASSURANCE

    Signature

    Approved by

    (DGM/QA)

    You might also like