Previews ACI 117 10 Pre

ACI 117-10
Specification for Tolerances for

Concrete Construction and Materials
(ACI 117-10) and Commentary
An ACI Standard
Reported by ACI Committee 117
First printing
June 2010
American Concrete Institute

Advancing concrete knowledge
Specification for Tolerances for Concrete Construction and Materials

and Commentary
Copyright by the American Concrete Institute, Farmington Hills, MI. All rights reserved. This material
may not be reproduced or copied, in whole or part, in any printed, mechanical, electronic, film, or other
distribution and storage media, without the written consent of ACI.
The technical committees responsible for ACI committee reports and standards strive to avoid ambiguities,
omissions, and errors in these documents. In spite of these efforts, the users of ACI documents occasionally
find information or requirements that may be subject to more than one interpretation or may be
incomplete or incorrect. Users who have suggestions for the improvement of ACI documents are
requested to contact ACI. Proper use of this document includes periodically checking for errata at
www.concrete.org/committees/errata.asp for the most up-to-date revisions.
ACI committee documents are intended for the use of individuals who are competent to evaluate the
significance and limitations of its content and recommendations and who will accept responsibility for the
application of the material it contains. Individuals who use this publication in any way assume all risk and
accept total responsibility for the application and use of this information.
All information in this publication is provided as is without warranty of any kind, either express or implied,
including but not limited to, the implied warranties of merchantability, fitness for a particular purpose or
non-infringement.
ACI and its members disclaim liability for damages of any kind, including any special, indirect, incidental,
or consequential damages, including without limitation, lost revenues or lost profits, which may result
from the use of this publication.
It is the responsibility of the user of this document to establish health and safety practices appropriate to
the specific circumstances involved with its use. ACI does not make any representations with regard to
health and safety issues and the use of this document. The user must determine the applicability of all
regulatory limitations before applying the document and must comply with all applicable laws and regulations,
including but not limited to, United States Occupational Safety and Health Administration (OSHA) health
and safety standards.
Order information: ACI documents are available in print, by download, on CD-ROM, through electronic
subscription, or reprint and may be obtained by contacting ACI.
Most ACI standards and committee reports are gathered together in the annually revised ACI Manual of
Concrete Practice (MCP).
American Concrete Institute
38800 Country Club Drive
Farmington Hills, MI 48331
U.S.A.
Phone:
248-848-3700
Fax:
248-848-3701
www.concrete.org
ISBN 978-0-87031-379-0
ACI 117-10
Specification for Tolerances for Concrete

Construction and Materials (ACI 117-10)
and Commentary
An ACI Standard
Reported by ACI Committee 117

Eldon G. Tipping
Chair
Scott Michael Anderson

Secretary
Scott M. Anderson
Allen Face
Donald M. Marks
David N. Peterson
Karl J. Bakke
Robert A. Halvorson
Ross S. Martin
William S. Phelan
David K. Ballast
Mark G. Josten
Steven W. McCrary
B. Duke Pointer
Bryan M. Birdwell
Richard L. Knox
Arthur W. McKinney
Peter J. Ruttura
Gregory P. Birley
Jeff L. LaRue
Colin T. Milberg
Michael J. Schneider
Thomas J. Downs
Michael W. Lee
William R. Nash
Bruce A. Suprenant
Ron Eldridge
Michael L. Leming
Bob L. Payne
Michael A. West
Specification synopsis: This specification provides standard tolerances for concrete construction and materials. This document is intended to be used
by specification writers and ACI committees writing standards as the reference document for establishing tolerances for concrete construction
and materials.
Commentary synopsis: This report is a commentary on the Specifications for Tolerances for Concrete Construction and Materials (ACI 117). It is intended
to be used with ACI 117 for clarity of interpretation and insight into the intent of the committee regarding the application of the tolerances set forth therein.
Keywords: architectural concrete; concrete; construction; drilled piers; formwork; foundation; mass concrete; pier; precast concrete; prestressed concrete;
reinforced concrete; reinforcement; specification; splice; tilt-up concrete; tolerances.
ACI 117 Specification and Commentary are presented in a sideby-side column format, with code text placed in the left column
and the corresponding commentary text aligned in the right
column. To distinguish the specification from the commentary, the
specification has been printed in Helvetica, which is the typeface
for this paragraph.
ACI Committee Reports, Guides, Manuals, and Commentaries

are intended for guidance in planning, designing, executing,
and inspecting construction. This document is intended for the
use of individuals who are competent to evaluate the
significance and limitations of its content and recommendations
and who will accept responsibility for the application of the
material it contains. The American Concrete Institute disclaims
any and all responsibility for the stated principles. The Institute
shall not be liable for any loss or damage arising therefrom.
Reference to this document shall not be made in contract
documents. If items found in this document are desired by the
Architect/Engineer to be a part of the contract documents, they
shall be restated in mandatory language for incorporation by
the Architect/Engineer.
The Commentary is printed in Times Roman, which is the typeface for

this paragraph. Commentary section numbers are preceded by the letter
R to distinguish them from specification section numbers. The
commentary is not a part of ACI Specification 117-10.
ACI 117-10 supersedes ACI 117-06 and was adopted March 1, 2010 and published
June 2010.
Copyright 2010, American Concrete Institute.
All rights reserved including rights of reproduction and use in any form or by any
means, including the making of copies by any photo process, or by electronic or
mechanical device, printed, written, or oral, or recording for sound or visual reproduction
or for use in any knowledge or retrieval system or device, unless permission in writing
is obtained from the copyright proprietors.
117-1
117-2
ACI STANDARD/COMMENTARY
CONTENTS
Introduction, p. 117-3
Section 1General requirements, p. 117-5
1.1Scope
1.2Requirements
1.3Definitions
1.4Referenced standards
Section 2Materials, p. 117-13
2.1Reinforcing steel fabrication and assembly
2.2Reinforcement location
2.3Placement of embedded items, excluding dowels in
slabs-on-ground
2.4Concrete batching
2.5Concrete properties
Section 3Foundations, p. 117-25
3.1Deviation from plumb
3.2Deviation from location
3.3Deviation from elevation
3.4Deviation from plane
3.5Deviation from cross-sectional dimensions of
foundations
Section 4Cast-in-place concrete for buildings,
p. 117-31
4.3Not used
4.5Deviation from cross-sectional dimensions
4.6Deviation from formed opening width or height
4.7Deviation from relative elevations or widths for stairs
4.8Deviation from slope or plane
4.9Sawcut depth in slab-on-ground
8.2Horizontal deviation
8.3Vertical deviation
8.4Cross-sectional dimension
Section 9Canal lining, p. 117-57
9.3Cross-sectional dimensions
Section 10Monolithic water-conveying tunnels,
siphons, conduits, and spillways, p. 117-59
Section 11Cast-in-place bridges, p. 117-61
11.4Length, width, or depth of specified elements
11.6Deck reinforcement cover
11.7Bearing pads
Section 12Exterior pavements and sidewalks,
p. 117-63
12.2Vertical deviation of surface
Section 13Chimneys and cooling towers,
p. 117-65
13.2Outside shell diameter
13.3Wall thickness
Section 5Cast-in-place concrete at interface with

precast concrete (except tilt-up concrete), p. 117-45
5.1Deviation from elevationcast-in-place concrete
5.2Deviation from locationcast-in-place concrete
5.3Deviation from dimensioncast-in-place concrete
5.4Deviation from plane at bearing surfacecast-inplace concrete measured over length or width of
bearing surface
Section 14Cast-in-place nonreinforced pipe,

p.117-67
14.1Wall thickness
14.2Pipe diameter
14.3Offsets
14.4Surface indentations
14.5Grade and alignment
14.6Concrete slump
Section 6Masonry, p. 117-51

This section has been removed.
Section 15Tilt-up concrete, p. 117-69

15.1Panel forming
15.5Deviation from slope or plane
15.6Deviation from relative widths
Section 7Cast-in-place, vertically slipformed

building elements, p. 117-53
7.1Deviation from plumb for buildings and cores
7.4Openings through elements
7.5Embedded plates
7.6Deviation from plumb for slipformed and jumpformed silos
Section 8Mass concrete, p.117-55
Notes to Specifier, p. 117-73

General notes
Foreword to checklists, p. 117-75
Mandatory Requirements Checklist, p. 117-75
Optional Requirements Checklist, p. 117-76
TOLERANCES FOR CONCRETE CONSTRUCTION
117-3
INTRODUCTION
SPECIFICATION
COMMENTARY
This commentary pertains to Specifications for Tolerances
for Concrete Construction and Materials (ACI 117-10).
The purpose of the commentary is to provide an illustrative
and narrative complement to the specification; it is not a
part of the specification.
No structure is exactly level, plumb, straight, and true.
Tolerances are a means to establish permissible variation in
dimension and location, giving both the designer and the
contractor limits within which the work is to be performed.
They are the means by which the designer conveys to the
contractor the performance expectations upon which the
design is based or that the project requires. Such specified
tolerances should reflect design assumptions and project
needs, being neither overly restrictive nor lenient.
Necessity rather than desirability should be the basis of
selecting tolerances.
As the title Specifications for Tolerances for Concrete
Construction and Materials (ACI 117) implies, the tolerances given are standard or usual tolerances that apply to
various types and uses of concrete construction. They are
based on normal needs and common construction techniques and practices. Specified tolerances at variance with
the standard values can cause both increases and decreases
in the cost of construction.
Economic feasibilityThe specified degree of accuracy has
a direct impact on the cost of production and the construction
method. In general, the higher degree of construction
accuracy required, the higher the construction cost, and the
lower the degree of construction accuracy, the higher the
cost of required repairs.
Relationship of all componentsThe required degree of
accuracy of individual parts can be influenced by adjacent
units and materials, joint and connection details, and the
possibility of the accumulation of tolerances in critical
dimensions.
Construction techniquesThe feasibility of a tolerance
depends on available craftsmanship, technology, materials,
and project management.
CompatibilityDesigners are cautioned to use finish and
architectural details that are compatible with the type and
anticipated method of construction. The finish and architectural details used should be compatible with achievable
concrete tolerances.

Previews ACI 117 10 Pre

Uploaded by

Copyright:

Available Formats

Previews ACI 117 10 Pre

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Previews ACI 117 10 Pre

Uploaded by

Copyright:

Available Formats

ACI 117-10

Specification for Tolerances for

Reported by ACI Committee 117

American Concrete Institute

Specification for Tolerances for Concrete Construction and Materials

Specification for Tolerances for Concrete

Reported by ACI Committee 117

Scott Michael Anderson

ACI Committee Reports, Guides, Manuals, and Commentaries

The Commentary is printed in Times Roman, which is the typeface for

Section 5Cast-in-place concrete at interface with

Section 14Cast-in-place nonreinforced pipe,

Section 6Masonry, p. 117-51

Section 15Tilt-up concrete, p. 117-69

Section 7Cast-in-place, vertically slipformed

Notes to Specifier, p. 117-73

TOLERANCES FOR CONCRETE CONSTRUCTION

You might also like