1. The system sweeps through the code every 20ms to acquire sensor values and check for accuracy, allowing for high precision monitoring and instant error detection and correction.
2. The system handles different operating modes based on whether the P3 sensor value and theoretical value match or indicate an error, with LED indicators blinking in error modes.
3. The system acquires data from sensors, converts it to a usable format, detects and isolates faults, corrects errors using interpolation, and has an interrupt service routine that sweeps through instructions every 20ms to monitor for issues.
1. The system sweeps through the code every 20ms to acquire sensor values and check for accuracy, allowing for high precision monitoring and instant error detection and correction.
2. The system handles different operating modes based on whether the P3 sensor value and theoretical value match or indicate an error, with LED indicators blinking in error modes.
3. The system acquires data from sensors, converts it to a usable format, detects and isolates faults, corrects errors using interpolation, and has an interrupt service routine that sweeps through instructions every 20ms to monitor for issues.
1. The system sweeps through the code every 20ms to acquire sensor values and check for accuracy, allowing for high precision monitoring and instant error detection and correction.
2. The system handles different operating modes based on whether the P3 sensor value and theoretical value match or indicate an error, with LED indicators blinking in error modes.
3. The system acquires data from sensors, converts it to a usable format, detects and isolates faults, corrects errors using interpolation, and has an interrupt service routine that sweeps through instructions every 20ms to monitor for issues.
1. The system sweeps through the code every 20ms to acquire sensor values and check for accuracy, allowing for high precision monitoring and instant error detection and correction.
2. The system handles different operating modes based on whether the P3 sensor value and theoretical value match or indicate an error, with LED indicators blinking in error modes.
3. The system acquires data from sensors, converts it to a usable format, detects and isolates faults, corrects errors using interpolation, and has an interrupt service routine that sweeps through instructions every 20ms to monitor for issues.
1. System sweeps through the code every 20ms.Thus various sensor values are acquisitted and checked for accuracy every 20ms thereby satisfying the demand for high precision and instant error detection and correction.
2. Following table gives an description of how different modes are handled by the system. Modes
P3 sensor
Output
LED 1
LED2
No error
P3 theoretical No error
P3 sensor
No output
No output
No error
Error
P3 sensor
No output
Blink
Error
No error
Blink
No output
Error
Error
P3 Theoretical Next lane
Blink
Blink
When both P3 sensor value and P3 theoretical value are in error, control is shifted to the next lane. 3. (About power on self-test).
(See if this is required)
Brief explanation of our project:
As already said, our model is an observer based design with a predictive unit developed on an empirical model.
Our system performances consists of
acquisition of data (Data being turbine pressure, NLR(speed),inlet pressure(taken as
constant at atmospheric pressure)
Conversion of data (Conversion to voltage in the range of 0-3.3v etc)
Fault detection
Isolation
Error correction using interpolation
Interrupt service routine
1. Acquisition of data:
For our project we need the values of turbine pressure and airplane speed measured in NLR. We input that data to DECU which is LPC2148 ARM microcontroller. We also need the value of inlet pressure. However, we conveniently assume it as constant as atmospheric pressure value. We need these values at every sample period(i.e. every 20ms)
2. Conversion of data:
To input turbine pressure and NLR to our DECU we need to represent them in the form of voltage in the range of 0 to 3.3V.
3. Fault Detection:
When there is an error in the input parameters i.e. Turbine pressure or NLR .our model immediately detects the fault
4. Fault Isolation:
Fault isolation is the practice of designing systems such that when there is fault, the negative consequences are limited in scope. Limiting the scope of problems reduces the potential for damage and makes systems easier to maintain.
We acquire P3 and NLR values every 20 ms and when there is a fault it is detected immediately. These make Fault isolation possible
5. Fault correction:
Based on the the datasheet which gives the relation between P3/P1 ratio and NLR, Weve developed an interpolated expression for P3 which acts as predictive model. So whenever a fault is detected, P3 can thus be indirectly measured.
6. Interrupt service routine:
Our controller is lpc2148 ARM, We have developed an interrupt service routine which sweeps through the instruction set every 20ms checking for P3,inspecting possible errors etc. It also performs power on self-check, ADC self-check etc.
