STATE OF CALIFORNIABUSINESS, TRANSPORTATION AND HOUSING AGENCY

California Test 670

February 2011

DEPARTMENT OF TRANSPORTATION
DIVISION OF ENGINEERING SERVICES
Transportation Laboratory
5900 Folsom Boulevard
Sacramento, California 95819 - 4612

METHOD OF TESTS FOR MECHANICAL AND WELDED

REINFORCING STEEL SPLICES
A.

SCOPE

This method presents the testing procedures for determining mechanical properties of spliced
reinforcing steel.
B.

REFERENCES

ASTM A 370 - Mechanical Testing of Steel Products

ASTM A 706/A 706M - Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement
Caltrans Standard Specifications - Section 52, Reinforcement
Concrete Reinforcing Steel Institute - CRSI Manual of Standard Practice
C.

APPARATUS
1. A tensile test machine able to apply a tensile force greater than the ultimate tensile
strength of the sample. This machine must be accurate and calibrated in
accordance with ASTM A 370.
2. A slip-measuring device consisting of two calibrated dial indicators that measure
displacement across the splice to the nearest 0.001 inch. A typical test set-up is
shown in Figure 1a. The dial indicators may have an analog dial or be digital.
Alternatively, extensometers accurate to within 0.001 inch can be used.
3. A calibrated caliper accurate to 0.001 inch.

D.

DEFINITIONS

Coupler mechanical device that physically connects two reinforcing bars.

Lot quantity of spliced reinforcing steel, as defined in Caltrans Standard Specifications,
Section 52.
Necking localized reduction in cross-section that may occur in material under tensile stress.
For this California Test, a sample has necking if the reduction in cross-section is visible, or if
the sample has sufficient ductility as determined by the strain measurement in Section E.3.d.
Sample spliced reinforcing steel bar that has the physical properties required in Section E.1.
Sample No. unique tracking number assigned to the sample(s) or set of samples being tested.
Slip test procedure for determining inherent axial displacement within the mechanical
coupler.
Splice physical device or mechanism for joining reinforcing steel, as defined in Caltrans
Standard Specifications, Section 52. Mechanical non-lap splices and resistance welded splices
are the most common types encountered. Per the Standard Specifications, splices can be
service or ultimate splices.
Rupture - Physical separation/fracture of the bar and/or mechanical coupler, or pull out of the
bar from the coupler.

California Test 670

February 2011

E.

TEST PROCEDURES FOR PRODUCTION TESTING AND QUALITY ASSURANCE TESTING

1. Physical Properties and Preparation

Each sample submitted for testing shall conform to the following requirements:
a. Sample length: For rebar sizes #9 and smaller, sample length must be at least 5 feet.
For rebar sizes #10 and larger, sample length must be at least 6 feet.
b. Test specimen length: The lab may shorten, machine, or otherwise alter the submitted
samples length to meet the configuration of its testing equipment within the following
limits:
(1) Mechanical splices: The minimum length of the test specimen between the grips of
the tensile testing machine shall be equal to 8d + 16 inches + Lc, where Lc is the
coupler length, and d is the nominal bar diameter. The coupler shall be located at
the center of the test specimen.
(2) Welded splices: The minimum length of the test specimen between the grips of the
tensile testing machine shall be equal to 28 inches.
c. Coupler length: For ultimate splice mechanical couplers only, the length of the coupler
must be less than 10 times the nominal bar diameter.
d. Alignment: With the exception of spliced hoops, the alignment across the splice must
be straight to within 0.5 inch along any 3-foot of length of the sample.
2.

Slip Test

The slip test is required for all mechanical splices except mechanical lap splices or splices that
are used on hoops. There are two acceptable options for measuring slip.
a. Slip Test (Option I)
Option I requires the use of two dial indicators to measure displacement across the
splice. Testing is performed as follows:
(1) Mount the sample in the tensile test machine.
(2) Attach the slip-measuring device so that the dial indicators are 180 apart as shown
in Figure 1a. During this step, the vertical bars shall be securely attached with the
hex socket bolts shown in Figure 1b.
(3) Once the measuring device is securely attached, release any restraining bars to
allow free movement of the device. For the testing device shown in 1a, this is done
by removing the hex socket bolts from the bottom end of the vertical bars as shown
in Figures 2a and 2b.
(4) Pre-stress the sample to 3,000 psi and then zero out the dial indicators.
(5) Apply an axial stress of 30,000 psi. Maintain this stress until a steady reading is
obtained on both dial indicators.
(6) Reduce the stress to 3,000 psi and record the two dial indicator readings. Take an
average of the two readings. This is the total slip. Record the total slip on the Test
Form (Figure 3).
(7) Remove the slip-measuring device.

-2-

California Test 670

February 2011

b. Slip Test (Option II)

Option II requires the use of punch marks to measure displacement across the splice.
Testing is performed as follows:
(1) Place one set of punch marks across the splice. The distance between the punch
marks should be approximately equal to the coupler length plus four bar diameters.
Using a permanent marker, label this side of the bar as A. Place a second set of
punch marks 180 apart from the first set and label that side of the bar as B.
(2) Pre-stress the sample to 3,000 psi.
(3) Measure the distance between the punch marks to the nearest 0.001 inch and
record these initial gage lengths on the Test Report Form (Figure 3).
(4) Apply an axial stress of 30,000 psi. Maintain this stress for 60 seconds.
(5) Reduce the stress to 3,000 psi and measure the final gage length between each set
of punch marks. For each set, calculate the slip as follows:
Slip (A, B) = (final gage length initial gage length)
(6) Average the results. This is the total slip. Record the total slip on the Test Report
Form (Figure 3).
3. Tensile Test
Tensile testing is required for all mechanical and welded splices and must be performed in
accordance with ASTM A 370 Sections 13 and A9, as follows:
a. Apply an axial tensile load to the sample sufficient to cause rupture.
b. Document the ultimate load obtained and describe or photographically document the
location of the rupture (bar, affected zone, or coupler) on the Test Report Form (Figure
3).
c. Calculate the ultimate tensile strength by dividing the ultimate load by the samples
nominal cross-sectional area. ASTM A 706, Table 1, provides the nominal crosssectional areas for ASTM A 706 reinforcing steel. Record the ultimate tensile strength
on the Test Report Form (Figure 3).
d. For ultimate splices check for necking. This can be done either visually (Option I) or by
determination of the strain value (Option II).
(1) Necking (Option I)
Examine the ruptured area. If there is a visible decrease in the samples cross-sectional
area at the point of rupture, then there is visible necking. Record the results on the
Test Report Form (Figure 3).
(2) Necking (Option II)
Alternatively, assess necking by determining the samples strain value following the
procedure described below:
a. Welded Splices:
1. For straight samples, place punch marks along the sides of the samples
to create a total of two 8-inch gage lengths, one on each side of the weld.

-3-

California Test 670

February 2011

Leave a gap of at least two bar diameters between the weld splice and the
8-inch gage marks (see figure below), and proceed to step 5.

2d

2d

2. For hoops, first determine the outside diameter of the hoop from
submittal documents. Record this information on the Test Report Form
(Figure 3). Next calculate the bar center to bar center hoop diameter (D)
as follows:
D = Dod bar nominal diameter
where:
Dod = hoop outside diameter
3. Place punch marks along the sides of the samples (not along the concave
or convex sides of the bar) to create a total of two 8-inch gage lengths,
one on each side of the weld. Label these gage lengths as A and B. Leave
a gap of at least two bar diameters between the weld splice and the
8-inch gage marks. See figure below:

2d

2d
8

4. Straighten the ends of the hoop samples to fit the sample into the testing
grips. This straightening should be outside of the gage marks, in
accordance with the Concrete Reinforcing Steel Institutes Manual of
Standard Practice MSP-1-90.
5. Mark each one of the 8-inch nominal gage lengths sequentially as A and B.
6. Measure and record the initial (Lo) of the two 8-inch gage lengths A and B
to the nearest 0.001 inch.
7. Tensile test the sample following the procedure in Section E.3.
8. Measure and record, to the nearest 0.001 inch, the final gage length (Lf)
not encompassing the location of the rupture.
9. For straight samples go to step 10 to calculate the percent strain. For
hoop samples, calculate the corrected final gage length as follows:
Corrected final gage length (Ln) = measured gage length
correction factor

Lf

Lf
D ArcSin
D

-4-

correction factor

California Test 670

February 2011

where:
Lf = measured final gage length in inches
D = diameter of the hoop (rebar center to rebar center in inches)
ArcSin should be expressed in radians.
10. Calculate the percent strain as follows:
For straight samples:
% strain = [(Lf Lo)/Lo]

100

100

For hoop samples:

% strain = [(Ln Lo)/Lo]

11. Record the calculated strain on the Test Report Form (Figure 3).
b. Mechanical Splices:
(1) Place punch marks as shown in the figure below:

Grip
2d
8
2d
d = bar diameter

Lc
2d
8
2d
Grip

(2) Mark each one of the 8-inch nominal gage lengths sequentially as A and
B.
(3) Individually, measure and record the initial (Lo) 8 inch gage lengths A
and B, to the nearest 0.001 inch.
(4) Tensile test each sample following the procedure in Section E.3.
(5) Measure and record the final gage length (Lf) not encompassing the
location of rupture, to the nearest 0.001 inch.
(6) Calculate the percent strain as follows:
% strain = [(Lf Lo)/Lo]

100

(7) Record the measured strain on the Test Report Form (Figure 3).
-5-

California Test 670

February 2011

F.

SUPPLEMENTARY TESTS FOR PREQUALIFICATION APPROVAL

1. Cyclical Testing
a. Cyclically load the sample from 5% to 90% of the specified yield strength (y) of the
sample for 100 cycles. Use a haversine waveform at 0.5 cps for #10, #11, #14, and #18
bars, and a haversine waveform at 0.7 cps for smaller bars. Record whether or not the
sample fractures.
b. If sample does not fracture during the cyclical test, increase the axial tensile load until
the sample fractures.
c. If applicable, record the ultimate load, ultimate tensile strength, location of failure, and
any necking on the Test Report Form (Figure 3).
2. Fatigue Testing
a. Fatigue load the sample from + 25,000 psi to 25,000 psi for 10,000 cycles. Use a sine
waveform at 0.083 cps for #10, #11, #14, and #18 bars, and a sine waveform at
0.35 cps for smaller bars. Record whether or not the sample fractures.
b. If the sample does not fracture during the fatigue test, increase axial tensile load until
the sample fractures.
c. If applicable, record the ultimate load, ultimate tensile strength, location of failure, and
any necking on the Test Report Form (Figure 3).
G.

REPORT

The test report form shown in Figure 3 is the recommended form to report test results.
Modification of this form is allowed as long as all the information listed in this figure is
reported in the modified form.
H.

HAZARDS

The test samples are heavy and may contain sharp edges or burrs. Sample rupture may
involve brittle fractures and ejection of sample fragments. Use appropriate safety measures.
I.

SAFETY AND HEALTH

It is the responsibility of the user of this test method to establish appropriate safety and health
practices and determine the applicability of regulatory limitations prior to use. Prior to
handling, testing or disposing of any materials, testers must be knowledgeable about safe
laboratory practices, hazards and exposure, chemical procurement and storage, and personal
protective apparel and equipment.
Caltrans Laboratory Safety Manual is available at:
http://www.dot.ca.gov/hq/esc/ctms/pdf/lab_safety_manual.pdf
End of Text
California Test 670 has 11 pages

-6-

California Test 670

February 2011

Figure 1a. Measuring device with dial indicators used for measuring slip.

Figure 1b. Close up of hex socket bolts used to hold the vertical
bars during the set up of the measuring device.
-7-

California Test 670

February 2011

Figure 2a. Close up of the removal of the hex socket bolts before testing.

Figure 2b. Measuring device ready for testing with bottom hex socket bolts removed.

-8-

California Test 670

February 2011

Figure 3. Test Report Form

TEST REPORT OF MECHANICAL SPLICES/WELDED BARS (Page 1 of 2)
Date Sampled:

Date Received:

Material

TL-101 No.

Lot No.

Sample No.:

Contract No.

Bar Size:

Manufacturer:

Splice Type:

Service or Ultimate?

Date Tested:

Lab Technician:

Testing Machine

Sampler/Inspector:
Test Results
Reported To:
Sample No. 1

Sample No. 2

Acceptable sample length?

Coupler within 10 times the bar
diameter?
Sample properly aligned?
Slip Test Option I:
Caliper 1 reading:
Caliper 2 reading:
Total slip (inch)
Slip Test Option II:
Initial gage length, Side A:
Final gage length, Side A:
Calculated slip, Side A:
Initial gage length, Side B:
Final gage length, Side B:
Calculated slip, Side B:
Total Slip (Avg. Side A + B)
TENSILE TEST:
Bar nominal area (sq. in.)
Ultimate load (lbs)
Ultimate tensile strength (psi)
Necking Option I:
Visible Necking?
Location of rupture?
Necking Option II:
A. Straight Sample:
Side A:
Initial gage length (Side A)
Final gage length (Side A)
Strain (Side A)

-9-

Sample No. 3

Sample No. 4

California Test 670

February 2011

Figure 3. Test Report Form

TEST REPORT OF MECHANICAL SPLICES/WELDED BARS (Page 2 of 2)
Sample No. 1

Sample No. 2

Sample No. 3

Sample No. 4

n/a

n/a

n/a

n/a

n/a

Side B:
Initial gage length (Side B)
Final gage length (Side B)
Strain (Side B)
B. Hoops:
Outside hoop diameter
Bar nominal diameter
Hoop diameter (D) - (bar center to bar
center)
Side A:
Initial gage length (Lo), Side A:
Final gage length (Lf), Side A:
Correction factor
Corrected final gage length (Ln), Side A
Strain (Side A)
Side B:
Initial gage length (Lo), Side B:
Final gage length (Lf), Side B:
Correction factor
Corrected final gage length (Ln), Side B
Strain (Side B)
CYCLICAL TESTING:
Specimen fractured?
FATIGUE TESTING:
Specimen fractured?

n/a

[ ] Samples pass.
[ ] Samples fail, because

- 10 -

California Test 670

February 2011

Figure 4. Digital calipers used to measure initial gage length to the nearest 0.001.

- 11 -