9000 Series

Cisco ASR 9000 Series
Aggregation Services Router

Hardware Installation Guide
January 2015
Cisco Systems, Inc.

www.cisco.com
Cisco has more than 200 offices worldwide.
Addresses, phone numbers, and fax numbers
are listed on the Cisco website at
www.cisco.com/go/offices.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not
installed in accordance with Ciscos installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Ciscos written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital
devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television
communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its
peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
Turn the television or radio antenna until the interference stops.
Move the equipment to one side or the other of the television or radio.
Move the equipment farther away from the television or radio.
Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits
controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCBs public
domain version of the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the
document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.
Cisco ASR 9000 Series Aggregation Services Router Hardware Installation Guide
2015 Cisco Systems, Inc. All rights reserved.
CONTENTS
Preface
Audience
Document Conventions
Related Documentation
Changes to This Document
Obtaining Additional Information and Support
CHAPTER
Preparing for Installation
1-1
Safety Guidelines 1-1

General Safety Guidelines 1-1
Compliance and Safety Information 1-2
Laser Safety 1-2
Energy Hazard 1-2
Preventing Electrostatic Discharge Damage
Lifting Guidelines 1-7
1-2
Site Requirement Guidelines 1-8

Site Layout and Equipment Dimensions 1-8
Site Wiring Guidelines 1-15
Chassis Air Flow Guidelines 1-15
Rack-Mounting and Air Flow Clearance Guidelines 1-20
Telco 2-Post Rack 1-21
Open 4-Post Rack 1-24
4-Post Enclosed Rack with Perforated Sides 1-26
Air Flow Guidelines for Enclosed Rack Installation 1-26
Cisco ASR 9010 Router Clearance Requirements 1-26
Cisco ASR 9006 Clearance Requirements 1-28
Temperature and Humidity Guidelines 1-36
Power Connection Guidelines 1-36
AC-Powered Routers 1-37
AC Power Cord Illustrations (Version 1 Power) 1-38
iii
Contents
AC Power Cord Illustrations (Version 2 and Version 3 Power) 1-43

DC-Powered Router 1-46
NEBS Supplemental Unit Bonding and Grounding Guidelines 1-52
RSP and RP Port Connection Guidelines 1-55
Console Port and Auxiliary Port Connection Guidelines
Console Port Signals 1-56
Auxiliary Port Signals 1-56
Management LAN Ports Connection Guidelines 1-57
Management LAN Port LED Indicators 1-57
Management LAN RJ-45 Cabling 1-58
Alarm Connection Guidelines 1-59
Sync Port Connection Guidelines 1-60
SFP/SFP+ Port 1-61
GPS Interface 1-61
Inter Chassis Synchronization Port 1-61
CMP Port 1-62
RSP Compact Flash Slot 1-62
USB Port 1-62
CHAPTER
Unpacking and Installing the Chassis
2-1
Pre-Installation Considerations and Requirements

Installation Overview 2-2
Required Tools and Equipment
1-55
2-1
2-3
Unpacking the Router 2-3

Unpacking the Cisco ASR 9010 Router 2-3
Positioning the Router 2-17
Positioning the Cisco ASR 9010 Router, Cisco ASR 9006 Router, and Cisco 9904 Router
Positioning the and Cisco ASR 9922 Router and Cisco ASR 9912 Router 2-17
2-17
Removing Components Before Installing the Chassis 2-18

Removing Power Modules 2-18
Removing Fan Trays 2-18
Removing a Fan Tray from the Cisco ASR 9010 Router, Cisco ASR 9922 Router, and Cisco ASR
9912 Router 2-18
Removing a Fan Tray from the Cisco ASR 9006 Router 2-21
Removing a Fan Tray from the Cisco ASR 9904 Router 2-22
iv
Contents
Removing Cards from the Chassis 2-23

Removing RSP Cards and Line Cards from the Cisco ASR 9010 Router, Cisco ASR 9006 Router,
and Cisco ASR 9904 Router 2-23
Removing RP Cards, Fabric Cards, and Line Cards from the Cisco ASR 9922 Router and Cisco ASR
9912 Router 2-31
Rack-Mounting the Router Chassis 2-42
Verifying Rack Dimensions 2-42
Installing the Chassis in a 2-Post Rack 2-43
Installing the Chassis in a 4-post Open Rack 2-49
Preparing the 19 Inch 45-RU Rack 2-49
Supplemental Bonding and Grounding Connections
2-56
Installing Chassis Accessories 2-61

Base Accessories 2-61
Optional Accessories 2-61
Installing Base Chassis Accessories on the Cisco ASR 9010 Router 2-61
Installing Optional Chassis Accessories on the Cisco ASR 9010 Router 2-64
Installing Optional Air Baffles on the Cisco ASR 9006 Router 2-75
Installing Optional Air Baffles on the Cisco ASR 9904 Router 2-82
CHAPTER
Installing Cards and Modules in the Chassis

Installing Power Modules 3-1
Installing AC Power Modules 3-2
Prerequisites 3-2
Steps 3-2
Installing DC Power Modules 3-4
Steps 3-4
Installing Fan Trays 3-4
Prerequisites 3-4
Steps 3-4
Installing Cards in the Chassis 3-6
Installing RSP Cards in the Chassis
3-1
3-2
3-4
3-4
3-7
Contents
RSP Cable Management Ties 3-9

Installing RP Cards in the Chassis 3-10
Installing Fabric Cards in the Chassis 3-11
Installing Line Cards in the Chassis 3-11
Connecting Line Card Network Interface Cables
3-17
Connecting Cables to the RSP or RP 3-22

Connecting to the Console Port 3-24
Connecting to the Auxiliary Port 3-24
Connecting to the Ethernet Management Ports
Connecting the Alarm Cable
3-24
3-25
Connecting Power to the Router 3-26

Connecting Power to an AC-Powered Router 3-26
Connecting Power to a DC-Powered Router 3-28
Powering On the Router
CHAPTER
3-32
Troubleshooting the Installation
4-1
Troubleshooting Overview 4-1

Troubleshooting Using a Subsystem Approach
Normal Router Startup Sequence 4-3
Identifying Startup Issues 4-4
4-2
Troubleshooting the Power Subsystem 4-7

Troubleshooting the AC Input Power Subsystem 4-7
Troubleshooting the DC Input Power Subsystem 4-12
Troubleshooting a DC Power Module 4-13
Additional Power Subsystem Troubleshooting Information 4-14
Obtaining Temperature and Environmental Information 4-14
Troubleshooting the Power Distribution System 4-18
Troubleshooting the Route Processor Subsystem 4-19
Route Processor Overview 4-19
RSP and RP Front Panel Indicators 4-25
LED Display Definitions 4-25
Compact Flash and Status LEDs 4-27
Ethernet Ports and Status LEDs 4-27
Auxiliary and Console Ports 4-28
Alphanumeric Message Displays 4-28
Flash Memory 4-29
Troubleshooting RSP and RP Cards 4-29
Fabric Card Front Panel Indicator 4-31
Troubleshooting Line Cards and Modular Port Adapters
vi
4-31
Contents
Monitoring Critical, Major, and Minor Alarm Status
4-32
Troubleshooting the Cooling Subsystem 4-32

Chassis Cooling Requirements 4-32
Fan Tray Operation 4-33
Power Module Fans 4-34
Overtemperature Conditions 4-34
Isolating Cooling Subsystem Problems 4-35
CHAPTER
Replacing Cisco ASR 9000 Series Router Components
5-1
Prerequisites and Preparation 5-1

Field Replaceable Units 5-2
Online Insertion and Removal 5-2
OIR Monitoring 5-3
Powering Off the Router 5-4
Replacing the Chassis Air Filter
5-4
Removing and Replacing the Fan Trays 5-11

Prerequisites 5-11
Required Tools and Equipment 5-11
Steps 5-11
Removing and Replacing Power System Components 5-12
Changing Between Version 1, Version 2, Version 3, AC, and DC Power Modules
Removing a Version 1 AC or DC Power Module 5-14
Removing a Version 2 or Version 3 AC or DC Power Module 5-15
Installing a Version 1 AC or DC Power Module 5-16
Installing a Version 2 or Version 3 AC or DC Power Module 5-16
Disconnecting AC Power 5-17
Reconnecting AC Power 5-17
Disconnecting DC Power 5-19
Reconnecting DC Power 5-20
Removing an AC or DC Power Tray from a Cisco ASR 9000 Series Router 5-21
Installing an AC or DC Power Tray into a Cisco ASR 9000 Series Router 5-23
Removing and Replacing Cards from the Chassis
Removing Cards from the Chassis 5-26
Replacing Cards in the Chassis 5-26
Removing a Chassis from the Equipment Rack
5-25
5-27
Installing a Replacement Chassis in the Equipment Rack

Packing a Chassis for Shipment
5-13
5-28
5-28
vii
Contents
APPENDIX
Technical Specifications
A-1
Cisco ASR 9000 Series Routers Physical Descriptions
A-2
Cisco ASR 9000 Series Routers Environmental Specifications=
A-3
Cisco ASR 9000 Series Routers AC Electrical Specifications
A-4
Cisco ASR 9000 Series Routers DC Electrical Specifications
A-6
AC Input and DC Input Voltage Range

AC Input Voltage Range A-7
DC Input Voltage Range A-7
A-7
Power System DC Output Levels A-8

DC Output Levels for Version 1 Power System
RSP/RP Port Specifications.
A-8
A-8
A-9
A-9
RSP Cards, RP Cards, and Fabric Card Power Consumption Specifications

Fan Tray Power Consumption Specifications
A-12
A-13
APPENDIX
Site Log
B-1
viii
A-10
Preface
This guide describes how to install a Cisco ASR 9000 Series Aggregation Services Router and its
components.
Audience, page 1
Document Conventions, page 1
Related Documentation, page 2
Changes to This Document, page 2
Obtaining Additional Information and Support, page 3
Audience
This guide is written for hardware installers and system administrators of Cisco routers.
This publication assumes that the user has a substantial background in installing and configuring router
and switch-based hardware. The reader should also be familiar with electronic circuitry and wiring
practices, and have experience as an electronic or electromechanical technician.
Document Conventions
Note
Means take note. Notes contain helpful suggestions or references to materials not contained in this
manual.
Timesaver
Means that the described action saves time. You can save time by performing the action described in the
paragraph.
Caution
Means be careful. You are capable of doing something that might result in equipment damage or loss of
data.
Warning
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. To see translations of the warnings that appear in
this publication, see the Regulatory Compliance and Safety Information document that accompanied
this device. Statement 1071
Related Documentation
For more information on the Cisco ASR 9000 Series Aggregation Services Router, refer to additional
documents found at:
http://www.cisco.com/c/en/us/support/routers/asr-9000-series-aggregation-services-routers/products-in
stallation-guides-list.html

Table 1 lists the technical changes made to this document since it was first created.
Table 1
Date
Change Summary
January 2015
Added new route processor cards RSP-440 Lite and RSP-880, FC2
fabric card, Cisco ASR 9222 support for the version 2 air filter,
support for the version 3 power system, and supported optics for
Cisco IOS XR software release 5.3.0.
October 2014
Information added for Cisco ASR 9922 version 2 fan tray.
June 2014
Information added about installing optional air baffles on the Cisco

ASR 9006 Aggregation Services Router.
September 2013 Information added about the Cisco ASR 9904 Aggregation
Services Router.
August 2013
Information added about the Cisco ASR 9912 Aggregation

Services Router.
May 2013
Information added about the Cisco ASR 9000v satellite shelf

adding support for the Cisco CRS Line Card Chassis in either the
8-slot or 16-slot variation.
February 2013
Updates and corrections made to various portions of the document.
December 2012
Information added about the Cisco ASR 9000v satellite shelf

adding support for the Cisco ASR 9922 Aggregation Services
Router and the Cisco ASR 9001 Aggregation Services Router.
Also, information added about the Cisco ASR 901 Series
Aggregation Services Router as a satellite shelf and the Cisco ASR
903 Series Aggregation Services Router as a satellite shelf.
Table 1
Date
Changes to This Document (continued)
Change Summary
September 2012 Information added about the new 1-port 40GE Modular Port
Adapter (MPA), 36-port 10GE line card, 1-port 100GE line card,
Cisco ASR 9922 Aggregation Services Router, RP card, FC card,
and Cisco ASR 9000v satellite shelf (adding support for the
A9K-36X10GE-TR [36-port 10GE line card, Packet Transport
Optimized] and A9K-36X10GE-SE [36-port 10GE line card,
Service Edge Optimized]).
May 2012
Information added about the new Cisco ASR 9000v (a satellite

system with the Cisco ASR 9000).
The Cisco ASR 9000v satellite shelf provides 44 1GE SFP ports
and 4 10GE SFP+ ports.
December 2011
Information added about the new RSP-440 Route Processor card,

the new 24-port 10GE fixed line card, the 2-port 100GE fixed line
card, and the modular line card supporting the 20-port 1GE MPA,
the 4-port 10GE MPA, and the 2-port 10GE MPA.
Information added about the new version 2 power system. The
Cisco ASR 9006 Router and Cisco ASR 9010 Router now support
version 1 and version 2 power systems.
May 2010
Added power consumption specifications for the new 16-port

10GE SFP+ line card. Updates and corrections made to various
portions of the document.
December 2009
Updates and corrections made to various portions of the document.
March 2009
Initial release of this document.
Obtaining Additional Information and Support

For information on obtaining documentation, submitting a service request to obtain support, and
gathering additional information, see the monthly Whats New in Cisco Product Documentation, which
also lists all new and revised Cisco technical documentation:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the Whats New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed,
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service, and Cisco currently supports RSS Version 2.0.
CH A P T E R

This chapter provides preinstallation information, such as recommendations and requirements you should be
perform before installing your Cisco ASR 9000 Series Router.
The shipping package for the router is engineered to reduce the chances of product damage associated
with routine material handling experienced during shipment:
Always transport or store the router in its shipping package in the upright position.
Keep the router in the shipping container until you have determined the installation site.
Inspect all items for shipping damage. If an item appears damaged, contact a Cisco customer service
representative immediately.
Safety Guidelines, page 1-1
Site Requirement Guidelines, page 1-8
RSP and RP Port Connection Guidelines, page 1-55
Safety Guidelines
Before you perform any procedure in this guide, you must review the safety guidelines in this section to
avoid injuring yourself or damaging the equipment.
Note that this section contains guidelines and do not include every potentially hazardous situation. When
you install a router, always use common sense and caution.
General Safety Guidelines
Never attempt to lift an object that might be too heavy for you to lift by yourself.
Always disconnect the power source and unplug all power cables before lifting, moving, or working
on the router.
Keep the work area clear and dust free during and after the installation.
Keep tools and router components away from walkways and equipment rack aisles.
Do not wear loose clothing, jewelry (including rings and chains), or other items that could get caught
in the router.
Fasten your tie or scarf and sleeves.
1-1
Chapter 1
Safety Guidelines
Operate Cisco equipment safely by using it in accordance with its electrical ratings and product
usage instructions.
Do not work alone if potentially hazardous conditions exist.
Always unplug the power cables when performing maintenance or working on the router, unless the
replacement part is hot swappable and designed for online insertion and removal (OIR).
Ensure that the installation of the router is in compliance with national and local electrical codes: in
the United States, National Fire Protection Association (NFPA) 70, United States National
Electrical Code; in Canada, Canadian Electrical Code, part I, CSA C22.1; in other countries,
International Electrotechnical Commission (IEC) 364, part 1 through part 7.
Compliance and Safety Information

The Cisco ASR 9000 Series Routers are designed to meet the regulatory compliance and safety approval
requirements. For detailed safety information, see:
Regulatory Compliance and Safety Information for the Cisco ASR 9000 Series Routers
Laser Safety
Single-mode Cisco ASR 9000 Series line cards are equipped with lasers. The lasers emit invisible
radiation. Do not stare into open line card ports. Observe the following warning to prevent eye injury:
Warning
Because invisible laser radiation may be emitted from the aperture of the port when no cable is
connected, avoid exposure to laser radiation and do not stare into open apertures. Statement 70
Energy Hazard
The Cisco ASR 9000 Series Routers can be configured for a DC power source. Do not touch terminals
while they are live. Observe the following warning to prevent injury.
Warning
Hazardous voltage or energy may be present on power terminals. Always replace cover when
terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in
place. Statement 1086
Preventing Electrostatic Discharge Damage

Many router components can be damaged by static electricity. Not exercising the proper electrostatic
discharge (ESD) precautions can result in intermittent or complete component failures. To minimize the
potential for ESD damage, always use an ESD-preventive antistatic wrist strap (or ankle strap) and
ensure that it makes good skin contact.
Note
Check the resistance value of the ESD-preventive strap periodically. The measurement should be
between 1 and 10 megohms.
1-2

Safety Guidelines
Before you perform any of the procedures in this guide, attach an ESD-preventive strap to your wrist and
connect the leash to the chassis as shown in the figures below.
Figure 1-1
ESD Label Information on Router Chassis
Figure 1-2
Connecting an ESD-Preventive Wrist Strap to the Cisco ASR 9010 Router Chassis
333558
ACO
ACO
LAMP
TEST
LAMP
TEST
FAIL
SYNC
CRIT
HDD
MAJ
CF
MIN
ACO
FAIL
CRIT
IMPORTANT
- CARDS
ARE PROPE
SYNC
HDD
MAJ
CF
MIN
ACO
RLY INSTALL
ED WHEN SCREW
S ARE TIGHTE
NED TO10 IN/LB
243184
Chapter 1
Location of chassis socket for ESD strap on the Cisco ASR 9010 Router chassis.
1-3
Chapter 1
Safety Guidelines
Figure 1-3
243408
1-4

Safety Guidelines
Figure 1-4
351293
Chapter 1
1-5
Chapter 1
Safety Guidelines
Figure 1-5
302358
1-6
Chapter 1

Safety Guidelines
Figure 1-6
303659
Lifting Guidelines
Fully configured Cisco ASR 9000 Series Routers can weigh as much as 1038 pounds (470.28 kg), and
an empty chassis weighs up to 300 pounds (136 kg). These systems are not intended to be moved
frequently. Before you install the router, ensure that your site is properly prepared to prevent moving the
router later to accommodate power sources and network connections.
Use the following lifting guidelines to avoid injury to yourself or damage to the equipment:
Warning
Do not lift equipment alone; have another person help you to lift heavy equipment.
Ensure that your footing is solid; balance the weight of the object between your feet.
Lift the equipment slowly; never move suddenly or twist your body as you lift.
Keep your back straight and lift with your legs, not your back. When bending down to lift
equipment, bend at the knees (not at the waist), to reduce the strain on your lower back muscles.
To prevent injury and equipment damage, never attempt to lift or tilt the router chassis using the
handles on the fan tray or on line cards. These handles do not support the weight of the chassis.
1-7
Chapter 1
Site Requirement Guidelines

The following sections contain the site requirement guidelines that you should be familiar with before
installing the router:
Site Wiring Guidelines, page 1-15
Chassis Air Flow Guidelines, page 1-15
Rack-Mounting and Air Flow Clearance Guidelines, page 1-20
Temperature and Humidity Guidelines, page 1-36
Power Connection Guidelines, page 1-36
NEBS Supplemental Unit Bonding and Grounding Guidelines, page 1-52
Site Layout and Equipment Dimensions

To help maintain trouble-free operation, adhere to the following precautions and guidelines when
planning your rack installation:
Install the system in a restrictive access location with means for a permanent ground.
Ensure the site of the rack includes provisions for source AC or DC power, grounding, and network
interface cables.
Allow sufficient space to work around the rack during the installation. You need:
At least 3 ft (91.44 cm) adjacent to the rack to move, align, and insert the chassis.
At least 2 ft (60.96 cm) in front of the power tray to insert power modules.
Maintain at least 24 inches (61 cm) of clearance in front of and behind the chassis for maintenance
after installation.
To mount the router between two posts or rails, the usable aperture (the width between the inner
edges of the two mounting flanges) must be at least:
17.50 inches (44.45 cm) for the Cisco ASR 9010 Router.
To mount the router in a 4-post rack, the usable aperture (the width between the inner edges of the
two mounting flanges) must be at least 17.75 inches (45.09 cm) for the Cisco ASR 9922 Router or
Cisco ASR 9912 Router.
Height of the Cisco ASR 9010 Router is 37.00 inches (93.98 cm). Most racks accommodate two
ASR 9010 routers.
Height of the Cisco ASR 9006 Router is 17.50 inches (44.45 cm). Most racks accommodate four
ASR 9006 routers,
Height of the Cisco ASR 9904 Router is 10.38 inches (26.7 cm). Most racks accommodate four or
more ASR 9904 routers.
Height of the Cisco ASR 9922 Router is 77.00 inches (195.58 cm). Most racks accommodate one
ASR 9912 router.
Height of the Cisco ASR 9912 Router is 52.50 inches (133.35 cm). Most racks accommodate one
ASR 9912 router.
1-8
Chapter 1

When fully populated with cards, the router can weigh up to 1038 pounds (470.28 kg). To maintain
equipment rack stability and to ensure your safety, the rack is provided with stabilizing devices.
Make sure you install the stabilizers before installing the router.
If you use a telco-style rack, the weight of the chassis is cantilevered off of the two rack posts. Make
sure that:
Weight of the router does not make the frame unstable.
Frame is bolted to the floor and is secured to the building structure using either wall brackets or
overhead brackets.
When mounting the router in a telco-style rack or 4-post rack, be sure to use all of the screws
provided to secure the chassis to the rack posts.
Install the cable-management brackets included with the router to keep cables organized. Be sure to:
Use appropriate strain-relief methods to protect cables and equipment connections.
Make sure that cables from other equipment installed in the rack do not restrict access to the
card cages.
To avoid noise interference in network interface cables, do not route them directly across or along
power cables.
Figure 1-7 shows the top-down view chassis dimensions of the Cisco ASR 9010 Router.
1-9
Chapter 1
Figure 1-7
Cisco ASR 9010 Router Chassis Footprint and DimensionsTop-Down View
Rear of chassis
17.38 in
(44.15 cm)
23.21 in
(58.95 cm)
28.93 in
(73.48 cm)
18.92 in
(48.06 cm)
Front of chassis
1-10
243432
5.04 in
(12.80 cm)

Figure 1-8
Rear of chassis
17.38 in
(44.15 cm)
28.93 in
(73.48 cm)
Rack
mounting
surface
5.73 in
(14.55 cm)
243430
Chapter 1
Front of chassis
1-11
Chapter 1
Figure 1-9
Rear of chassis
2.45 in
(6.22 cm)
17.57 in
(44.64 cm)
25.02 in
(63.54 cm)
6.00 in
(15.24 cm)
6.00 in
(15.24 cm)
Rack
mounting
surface
2.45 in
(6.22 cm)
18.97 in
(48.19 cm)
Front of chassis
1-12
351294
2.282 in
(5.79 cm)

Figure 1-10

Rear of chassis
30.11 in
(76.48 cm)
22 in
(55.88 cm)
5.05 in
(13.97 cm)
17.60 in
(44.70 cm)
Front of chassis
343945
Chapter 1
1-13
Chapter 1
Figure 1-11
Rear of chassis
18.97 in
(48.18 cm)
29.44 in
(74.78 cm)
17.60 in
(44.70 cm)
Front of chassis
1-14
303667
22 in
(55.88 cm)
Chapter 1

Site Wiring Guidelines

When planning the location of the router, consider distance limitations for signaling, electromagnetic
interference (EMI), and connector compatibility. If the wiring is run for any significant distance in an
electromagnetic field, interference can occur between the field and the signals on the wires. Poor wiring
can cause:
Radio interference emanating from the wires.
Strong EMI, especially when caused by lightning or radio transmitters. EMI can destroy the signal
drivers and receivers in the router, and can even create an electrical hazard by conducting power
surges through lines and into equipment.
Note
To predict and remedy strong EMI, you may need to consult with experts in radio frequency
interference (RFI).
Site wiring is unlikely to emit radio interference if you use twisted-pair cable with a good distribution
of grounding conductors. Use a high-quality twisted-pair cable with one ground conductor for each data
signal, when applicable.
Give special consideration to the effect of a lightning strike in your vicinity, especially if the wiring
exceeds the recommended distances, or if it passes between buildings. The electromagnetic pulse (EMP)
caused by lightning or other high-energy phenomena can easily induce enough energy into unshielded
conductors to destroy electronic devices. If you have experienced EMP problems in the past, you may
want to consult experts in electrical surge suppression and shielding.
Most data centers cannot resolve infrequent but potentially catastrophic problems without pulse meters
and other special equipment. In addition, these problems can take a great deal of time to identify and
resolve. We recommend that you take the necessary precautions to avoid these problems by providing a
properly grounded and shielded environment, with special attention to issues of electrical surge
suppression.
Chassis Air Flow Guidelines

Table 1-1 describes how cool air is circulated through the Cisco ASR 9000 Series Routers.
Table 1-1
Chassis Air Flow Guidelines
Router Type
Chassis Air Flow
Cisco ASR 9010
Air is circulated by two fan trays located underneath the Route Switch Processor
(RSP) and line cards as shown in Figure 1-12.
Cisco ASR 9006
Air is circulated by two fan trays located along the top left side above the RSP
and line cards as shown in Figure 1-13.
Cisco ASR 9904
Air is circulated side-to-side by a single fan tray located along the left side of
the chassis as shown in Figure 1-14.
If the router is installed in a 2-post 23-inch rack, air flow is circulated
front-to-back. Optionally, you can install air baffles on the chassis to help
isolate the exhaust air from the intake air. For more information, see Installing
Optional Air Baffles on the Cisco ASR 9904 Router, page 2-82.
1-15
Chapter 1
Table 1-1
Chassis Air Flow Guidelines (continued)
Router Type
Chassis Air Flow
Cisco ASR 9922
Air circulated by four fan trays as shown in Figure 1-15. Two fan trays are
located between the line cards in the top cage and the RP and Switch Fabric
Cards (FCs) in the middle cage. Another two fan trays are located between the
middle cage and the line cards in the bottom cage.
Cisco ASR 9912
Air is circulated by two fan trays located above the line cards as shown in
Figure 1-16.
The fan trays maintain acceptable operating temperatures for the internal components by drawing in cool
air through the air filter, and circulating the air through the card cage. Each power supply is also
equipped with fans that draw cooler air into the front of the power supply and force warmer air out of
the back of the chassis. For information about the types of fan trays used in the chassis, see Power
Module Fans, page 4-34.
Note
See Rack-Mounting and Air Flow Clearance Guidelines, page 1-20 for details on air-flow clearance
requirements for installation in an enclosed 4-post rack.
Figure 1-12
Air Flow Path through the Cisco ASR 9010 RouterSide View
Air exhaust
Rear air
exhaust plenum
RSPs and line cards
Fan trays
Room air
Power modules
1-16
242696
Power modules
Front air
intake

Figure 1-13
Air Flow Path through the Cisco ASR 9006 RouterFront View
Air exhaust
Fan trays
RSPs and line cards
Power modules
Figure 1-14
243379
Room air
Air Flow Path through the Cisco ASR 9904 RouterFront View
RSPs and line cards
Room air
Air exhaust
351295
Chapter 1
Power modules
1-17
Chapter 1
Figure 1-15
Power modules
Air exhaust
Rear Air
exhaust plenum
Line cards
Fan trays
RPs and FCs
RPs and FCs
Fan trays
Rear Air
exhaust plenum
Air exhaust
1-18
343957
Line cards

Figure 1-16
Air exhaust
Fan trays
Rear Air
exhaust plenum
Line cards
RPs and FCs
Power trays
303670
Chapter 1
When selecting a site to install the router, observe the following guidelines:
Dust-free areaThe site should be as dust-free as possible. Dusty environments can clog the air
filter or power supply intake vents, reducing the cooling air flow through the router. Clogged filters
and vents can cause an overtemperature condition in the router.
Unrestricted air-flowAllow sufficient air-flow by maintaining a minimum of 6 in (15.24 cm) of

clearance at both the inlet and exhaust openings on the chassis and the power modules. If the air flow
is blocked or restricted, or if the inlet air is too warm, an overtemperature condition can occur within
the router. Under extreme conditions, the environmental monitoring system powers off the router to
protect the components.
1-19
Chapter 1
Rack-Mounting and Air Flow Clearance Guidelines

The Cisco ASR 9010 Router, Cisco ASR 9006 Router, and Cisco ASR 9904 Router c an be installed in
most 2-post, 4-post, or telco-style 19-inch equipment racks that comply with the Electronics Industries
Association (EIA) standard for equipment racks (EIA-310-D).
Note
The Cisco ASR 9922 Router and Cisco ASR 9912 Router can be mounted only in a 4-post rack. The rack
must have at least two posts with mounting flanges to mount the router chassis. The distance between
the center lines of the mounting holes on the two mounting posts must be 18.31 inches 0.06 inch
(46.50 cm 0.15 cm).
Figure 1-17 shows an examples of typical 2-post and 4-post telco-type equipment racks.
Telco-Type Equipment Racks
243453
Figure 1-17
Telco- b Free-standing, 4-post open rack with

style
two mounting posts in the front, two
rack
mounting posts in the back or along each
side.
1-20
c Free-standing enclosed rack with

perforated sides and two mounting posts
in the front.
Chapter 1

Telco 2-Post Rack

Item a in Figure 1-17 shows a telco-style rack. The telco-style rack is an open frame consisting of two
posts tied together by a cross-bar at the top and a floor stand at the bottom.
This type of rack is usually secured to the floor and sometimes to an overhead structure or wall for
additional stability. The router chassis can be installed in the telco-style rack only in a front-mounted
position.
In the front-mounted position, you secure the chassis rack-mounting brackets directly to the rack posts
(see Figure 1-18 for the Cisco ASR 9010 Router, Figure 1-19 for the Cisco ASR 9006 Router, and
Figure 1-20 for the Cisco ASR 9904 Router). Two rear mounting brackets are provided for mounting the
Cisco ASR 9010 Router in a 2-post rack.
The mounting brackets on the Cisco ASR 9006 Router chassis have a pair of holes at the top and bottom
of each bracket; the remaining openings in the brackets are slots. When mounting the router in a 2-post
rack, you must first use the holes to locate and position the brackets on the rack. Insert the screws through
the bracket holes into the rack before inserting screws through the bracket slots.
Figure 1-18
Cisco ASR 9010 Router Mounted in a 2-Post Rack
243186
Note
1-21
Chapter 1
243496
Figure 1-19
1-22

Figure 1-20
351296
Chapter 1
1-23
Chapter 1
Open 4-Post Rack

Item b in Figure 1-17 shows a free-standing, 4-post open rack with two mounting posts in the front and
two mounting posts in the back or along the side. The mounting posts in this type of rack are often
adjustable so that you can position the rack-mounted unit within the depth of the rack rather than
flush-mount it with the front of the rack.
Two rear mounting brackets are provided for mounting the Cisco ASR 9010 Router in a 4-post rack.
Two rear mounting brackets and two bottom guide rails are provided for mounting the
Cisco ASR 9922 Router (Figure 2-8) and Cisco ASR 9912 Router (Figure 2-12) in a 4-post rack.
Rear brackets or are necklaces are not provided for mounting the Cisco ASR 9904 Router in a 4-post
rack.
Cisco ASR 9912 Router Mounted in an Open 4-Post Rack
302352
Figure 1-21
1-24

Figure 1-22
Cisco ASR 9912 Router Mounted in an Open 4-Post Rack
303660
Chapter 1
1-25
Chapter 1
4-Post Enclosed Rack with Perforated Sides

Item c in Figure 1-17 shows a free-standing 4-post enclosed rack with perforated sides and two mounting
posts in the front.
Caution
Do not install the Cisco ASR 9000 Series Router in any type of fully enclosed rack that does not have
the required perforated sides or doors; the router requires an unobstructed flow of cooling air to maintain
acceptable operating temperatures for its internal components. Installing the router in any type of fully
enclosed rack without proper perforation could disrupt the air-flow, trap heat next to the chassis, and
cause an overtemperature condition inside the router.
Air Flow Guidelines for Enclosed Rack Installation

Follow these guidelines when installing the Cisco ASR 9000 Series Routers in a 4-post enclosed rack.
Cisco ASR 9010 Router Clearance Requirements

To install a Cisco ASR 9010 Router in a 4-post enclosed cabinet:
The front and rear doors of the cabinet must be removed or be perforated with a minimum open area
of 65 percent (70 percent for ETSI 800-mm racks).
Ensure that you have the following clearances around the chassis:
Rear: Minimum of 3.15 inches (8.00 cm) of clearance.
Sides: Minimum of 2.87 inches (7.28 cm) of clearance on each side of the chassis.
Figure 1-23 shows the side and rear chassis air-flow clearance requirements for mounting the
Cisco ASR 9010 Router in a 4-post enclosed rack.
1-26

Figure 1-23
2.87 in
(7.28 cm)
Cisco ASR 9010 Router Clearance Requirements for an Enclosed 4-Post Rack
Installation
Rear of chassis
3.15 in
(8.00 cm)
2.87 in
(7.28 cm)
ASR 9010
Rack
mounting
surface
5.04 in
(12.80 cm)
Front of chassis
245629
Chapter 1
1-27
Chapter 1
Cisco ASR 9006 Clearance Requirements

To install a Cisco ASR 9006 Router in a 4-post enclosed cabinet:
of 70 percent. In addition, the right side panel must be removed or perforated with a minimum of 65
percent open area (70 percent for ETSI 800-mm racks).
There must be a minimum unobstructed space of 6 inches (15.24 cm) between the routers right side
air inlet and the adjacent wall or cabinet side panel, and a minimum unobstructed space of 6 inches
(15.24 cm) between adjacent cabinets. In addition, there should be no exhaust from any source
blowing into the right side panel of the cabinet.
Rear chassis clearance: Minimum of 2.50 inches (6.40 cm) of clearance.
Sides chassis clearance: Minimum of 6 inches (15.24 cm) of clearance on the right side of the
chassis (as viewed from the front). There is no clearance requirement for the left side of the
chassis.
Figure 1-24 shows the side and rear chassis air-flow clearance requirements for mounting the Cisco ASR
9006 Router in a 4-post enclosed rack.
1-28

Figure 1-24
Cisco ASR 9006 Router Clearance Requirements for an Enclosed 4-Post Rack
Installation
Rear of chassis
2.50 in
(6.40 cm)
No minimum clearance
requirement for left
side of chassis.
6.00 in
(15.20 cm)
ASR 9006
Rack
mounting
surface
5.73 in
(14.55 cm)
Front of chassis
245630
Chapter 1
1-29
Chapter 1

To install the Cisco ASR 9904 Router in a 4-post enclosed cabinet:
Rear: Minimum of 2.45 inches (62.2 cm) of clearance.
Figure 1-25 shows the side and rear chassis air-flow clearance requirements for mounting the Cisco ASR
9904 Router in a 4-post enclosed rack.
1-30
Chapter 1

Figure 1-25
Cisco ASR 9904 Router Clearance Requirements in a 4-Post Rack Installation
Rear of chassis
2.45 in
(6.22 cm)
17.57 in
(44.64 cm)
25.02 in
(63.54 cm)
6.00 in
(15.24 cm)
6.00 in
(15.24 cm)
Rack
mounting
surface
2.45 in
(6.22 cm)
18.97 in
(48.19 cm)
351294
2.282 in
(5.79 cm)
Front of chassis
1-31
Chapter 1

of 70 percent (80 percent for ETSI 800-mm racks).
Rear: Minimum of 10 inches (25.4 cm) of clearance.
Sides: Minimum of 2.87 inches (7.28 cm) clearance on each side of the chassis.
Figure 1-26 shows the clearance requirements for mounting the Cisco ASR 9922 Router in a 4-post
enclosed rack.
1-32

Figure 1-26
10 in
(25.40 cm)
Rear of chassis
2.87 in
(7.28 cm)
2.87 in
(7.28 cm)
Rack
mounting
surface
4.50 in
(11.43 cm)
Front of chassis
302422
Chapter 1
1-33
Chapter 1

of 70 percent open area (80 percent for ETSI 800-mm racks).
Rear: Minimum of 10 inches (25.4 cm) of clearance.
Figure 1-27 shows the side and rear chassis air-flow clearance requirements for mounting the router in
a 4-post enclosed rack.
1-34

Figure 1-27
10 in
(25.40 cm)
Rear of chassis
2.87 in
(7.28 cm)
2.87 in
(7.28 cm)
Rack
mounting
surface
6.30 in
(16 cm)
Front of chassis
303661
Chapter 1
1-35
Chapter 1
Temperature and Humidity Guidelines

The operating and nonoperating environmental site requirements are listed in Table A-2. The router
normally operates within the ranges listed in the table; however, if a temperature measurement is
approaching a minimum or maximum parameter, it indicates a potential problem. Maintain normal
operation by anticipating and correcting environmental anomalies before they approach critical values
by properly planning and preparing your site before you install the router.
Power Connection Guidelines

You can configure the router with either an AC input or DC input power subsystem, so the site power
source requirements differ depending on the power subsystem in your router. Ensure all power
connection wiring conforms to the rules and regulations in the National Electrical Code (NEC) as well
as local codes.
Caution
Each Cisco ASR 9000 Series Router is powered by only one type of input: AC or DC. A hybrid (AC+DC)
power configuration is not supported.
Table 1-2
Cisco ASR 9000 Series Routers Supported Power Systems
Router
Supported Power Systems
Cisco ASR 9006
Version 1: Supports up to three power modules in the power tray.

Version 2: Supports up to four power modules in the power tray
Compatible only with Cisco IOS XR Software Release 4 and
later Cisco IOS XR software releases.
Cisco ASR 9010
Version 1: Supports up to three power modules in the power tray.

Version 2: Supports up to four power modules in the power tray
Version 3: Supports up to four DC power modules in the DC
power tray and up to three AC power modules in the AC power
tray. Compatible only with Cisco IOS XR Software Release
5.3.0 and later Cisco IOS XR software releases.
Cisco ASR 9904
Version 2: Supports up to four power modules in the power tray.

Cisco ASR 9922, Cisco ASR 9912 Version 2: Supports up to four power modules in the power tray.
Version 3: Supports up to four DC power modules in the DC
power tray and up to three AC power modules in the AC power
tray. Compatible only with Cisco IOS XR Software Release
5.3.0 and later Cisco IOS XR software releases.
Caution
Proper grounding is necessary to avoid damage from lightning and power surges. See NEBS
Supplemental Unit Bonding and Grounding Guidelines, page 1-52 for grounding requirements.
1-36
Chapter 1

AC-Powered Routers
AC power modules operate in the input range of 180 VAC to 264 VAC, 47 to 63 Hz (nominal input level
of 200 to 240 VAC). Refer to Table 1-3 and Table 1-4 for the minimum required AC service for version
1 and version 2 power modules.
Power redundancy requirements vary based on the system configuration (number and type of line cards,
etc.). AC-powered systems are 2N protected. A minimum of two power supplies are required for
redundant operation. Refer to the Cisco ASR 9000 Power Calculator at the following URL to determine
actual redundancy requirements for any given configuration: http://tools.cisco.com/cpc/launch.jsp.
Each of the AC power inputs requires a separate dedicated branch circuit. Note that the circuit breaker
and fuse lockout procedures should follow the rules and regulations in the National Electrical Code
(NEC) and any local codes. For a list of the nominal and acceptable value ranges for source AC power,
see Table A-5.
Table 1-3 lists the AC input power cord options, specifications, and Cisco product numbers for the AC
input version 1 power supply modules. Table 1-4 lists the AC input power cord options, specifications,
and Cisco product numbers for the AC input version 2 power supply modules.
Note
Before connecting AC input power cords to the power system, make sure that the power cords are not
energized.
Table 1-3
AC Input Power Cord Options for Version 1 Power System
Locale
Part Number
Length
Plug Rating
Power Cord
Reference
Illustration
Australia,
New Zealand
CAB-7513ACA=
14 ft (4.3 m)
15 A, 250 VAC
Figure 1-28
Australia,
New Zealand
CAB-AC-16A-AUS=
14 ft (4.3 m)
16A, 250 VAC
Figure 1-29
China
CAB-AC16A-CH=
14 ft (4.3 m)
16 A, 250 VAC
Figure 1-30
Continental Europe
CAB-7513ACE=
14 ft (4.3 m)
16 A, 250 VAC
Figure 1-31
CAB-2500W-EU=
16 A, 250 VAC
Figure 1-32
CAB-AC-2500W-EU=
16 A, 250 VAC
Figure 1-33
International
CAB-AC-2500W-INT=
14 ft (4.3 m)
16 A, 250 VAC
Figure 1-34
Israel
CAB-AC-2500W-ISRL=
14 ft (4.3 m)
16 A, 250 VAC
Figure 1-35
Italy
CAB-7513ACI=
14 ft (4.3 m)
16 A, 250 VAC
Figure 1-36
Japan, North
America
(nonlocking plug)
200240VAC
operation
CAB-AC-2500W-US1=
14 ft (4.3 m)
20 A, 250 VAC
Figure 1-37
Japan, North
America (locking
plug)
200240VAC
operation
CAB-AC-C6K-TWLK=
14 ft (4.3 m)
20 A, 250 VAC
Figure 1-38
1-37
Chapter 1
Table 1-3
AC Input Power Cord Options for Version 1 Power System
Locale
Part Number
Length
Plug Rating
Power Cord
Reference
Illustration
South Africa
CAB-7513ACSA=
14 ft (4.3 m)
16 A, 250 VAC
Figure 1-39
Switzerland
CAB-ACS-16=
14 ft (4.3 m)
16 A, 250 VAC
Figure 1-40
Table 1-4
AC Input Power Cord Options for Version 2 and Version 3 Power System
Locale
Part Number
Length
Plug Rating
Reference
Illustration
China
PWR-CAB-AC-CHN=
13.9 ft (4.3 m)
16 A, 250 V
Figure 1-41
Europe
PWR-CAB-AC-EU=
13.9 ft (4.3 m)
16 A, 250 V
Figure 1-42
Israel
PWR-CAB-AC-ISRL=
13.9 ft (4.3 m)
16 A, 250 V
Figure 1-43
USA
PWR-CAB-AC-USA=
13.9 ft (4.3 m)
20 A, 250 V
Figure 1-44
Australia
PWR-CAB-AC-AUS=
13.9 ft (4.3 m)
16 A, 250 V
Figure 1-45
Italy
PWR-CAB-AC-ITA=
13.9 ft (4.3 m)
16 A, 250 V
Figure 1-46
Brazil
PWR-CAB-AC-BRA=
13.9 ft (4.3 m)
16 A, 250 V
Figure 1-47
South Africa
PWR-CAB-AC-SA=
13.9 ft (4.3 m)
16 A, 250 V
Figure 1-48
UK
PWR-CAB-AC-UK=
13.9 ft (4.3 m)
16 A, 250 V
Figure 1-49
Switzerland
PWR-CAB-AC-SUI=
13.9 ft (4.3 m)
16 A, 250 V
Figure 1-50
Japan
PWR-CAB-AC-JPN=
13.9 ft (4.3 m)
20 A, 250 V
Figure 1-51
AC Power Cord Illustrations (Version 1 Power)

This section contains the AC power cord illustrations for version 1 power, as described in Table 1-3.
Note that an AC power cord may be used with several power supplies.
Figure 1-28 AC Power Cord CAB-7513ACA=
Plug: SAA AS 3112
Cordset rating: 15 A, 250 V

Length: 14 ft 0 in. (4.26 m)
113353
Connector: IEC 60320 C19
1-38

Figure 1-29 AC Power Cord CAB-AC-16A-AUS

Length: 14 ft 0 in. (4.26 m)
Plug: AU20S3
140586
Figure 1-30 AC Power Cord CAB-AC16A-CH=
Connector: IEC
60320-1 C19
126792
Plug: GB16C
Cordset rating: 16A, 250V

Length: 14 ft 0 in. (4.26 m)
Figure 1-31 AC Power Cord CAB-7513ACE=
Plug: CEE 7/7

Length: 14 ft 0 in. (4.26 m)
113354
Chapter 1
1-39
Chapter 1
Figure 1-32 AC Power Cord CAB-2500W-EU=
Plug: CEE 7/7

Length: 14 ft 0 in. (4.26 m)
113360
Figure 1-33 AC Power Cord CAB-AC-2500W-EU=
Plug: CEE 7/7

Length: 14 ft 0 in. (4.26 m)
113360
Figure 1-34 AC Power Cord CAB-AC-2500W-INT=

Length: 14 ft 0 in. (4.26 m)
Plug: IEC 309
113361
1-40

Figure 1-35 AC Power Cord CAB-AC-2500W-ISRL=
Plug: SI16S3

Length: 14 ft 0 in. (4.26 m)
130113
Figure 1-36 AC Power Cord CAB-7513ACI=
Plug: SAA AS 3112

Length: 14 ft 0 in. (4.26 m)
113353
Figure 1-37 AC Power Cord CAB-AC-2500W-US1=
Plug: NEMA 6-20

Length: 14 ft 0 in. (4.26 m)
113362
Chapter 1
1-41
Chapter 1
Figure 1-38 AC Power Cord CAB-AC-C6K-TWLK=
Plug: NEMA L6-20

Length: 14 ft 0 in. (4.26 m)
113363
Figure 1-39 AC Power Cord CAB-7513ACSA=
Plug: IEC 884

Length: 14 ft 0 in. (4.26 m)
113357
Figure 1-40 AC Power Cord CAB-ACS-16=

Length: 8 ft 2 in. (2.5 m)
113364
Plug: SEV 5934-2

Type 23
1-42
Chapter 1

AC Power Cord Illustrations (Version 2 and Version 3 Power)

This section contains the AC power cord illustrations for version 2 power, as described in Table 1-4.
Figure 1-41 AC Power Cord PWR-CAB-AC-CHN=
Cordset rating: 16A, 250V

Length: 13.94 ft. (4.25 m)
Plug: GB2099.1/GB1002
331430
Connector: IEC-320-C21
Figure 1-42 AC Power Cord PWR-CAB-AC-EU=
Plug: CEE 7/7

Length: 13.94 ft. (4.25 m)
331426
Figure 1-43 AC Power Cord PWR-CAB-AC-ISRL=
Plug: SI 32

Length: 13.94 ft. (4.25 m)
331429
1-43
Chapter 1
Figure 1-44 AC Power Cord PWR-CAB-AC-USA=
Plug: NEMA L6-20 P

Length: 13.94 ft. (4.25 m)
331422
Figure 1-45 AC Power Cord PWR-CAB-AC-AUS=
Plug: AU20S3

Length: 13.94 ft. (4.25 m)
331423
Figure 1-46 AC Power Cord PWR-CAB-AC-ITA=
Plug: CEI-23-50

Length: 13.94 ft. (4.25 m)
331425
1-44

Figure 1-47 AC Power Cord PWR-CAB-AC-BRA=

Length: 13.94 ft. (4.25 m)
Plug: NBR 14136
331431
Figure 1-48 AC Power Cord PWR-CAB-AC-SA=
Plug: SABS 164

Length: 13.94 ft. (4.25 m)
331428
Figure 1-49 AC Power Cord PWR-CAB-AC-UK=

Length: 13.94 ft. (4.25 m)
Plug: EN-60309-2
331431
Chapter 1
1-45
Chapter 1
Figure 1-50
AC Power Cord PWR-CAB-AC-SUI=
Plug: SEV 5934

Length: 13.94 ft. (4.25 m)
331427
Figure 1-51 AC Power Cord PWR-CAB-AC-JPN=
Plug: JIS C8303

Length: 13.94 ft. (4.25 m)
331424
DC-Powered Router
Connections to DC power modules are rated at 60 A maximum. The system accepts a nominal input voltage
of 48 VDC with an operational tolerance range of 40 VDC to 72 VDC. One dedicated, commensurately
rated DC power source is required for each power module connection.
Power redundancy requirements vary based on the system configuration (number and type of line cards,
etc.). DC-powered systems are N+1 protected. A minimum of two power supplies are required for
redundant operation. Refer to the Cisco ASR 9000 Power Calculator to determine actual redundancy
requirements for any given configuration. See: http://tools.cisco.com/cpc/launch.jsp.
Power connections to the power tray for each DC power module requires four cables: two source cables
and two return cables. In addition, each DC power tray requires one earth ground, so the minimum
number of cables for connecting a single DC power module in a power tray is five (two source, two
return, one ground).
Note
A separate ground connection is not required for the version 2 and version 3 power systems. For more
information see NEBS Supplemental Unit Bonding and Grounding Guidelines, page 1-52.
1-46
Chapter 1

For DC power cables, we recommend that you use 60-A-rated, high-strand-count copper wire cables.The
length of the cables depends on your router location from the source power. DC power cables are not
available from Cisco, but they are available from any commercial cable vendor.
You must terminate DC power cables using cable lugs at the power tray end. Ensure that the lugs are
dual-hole and that they fit over M6 terminal studs at 0.625-inch (15.88-mm) centers. For #4 AWG cable,
use Panduit part number LCD4-14AF-L or equivalent; for #6 AWG, use Panduit part number
LCD6-14AF-L or equivalent.
Warning
Hazardous voltage or energy may be present on power terminals. Always replace cover when
terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in
place. Statement 1086
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Note
Before connecting DC power cords to the power system, make sure that the input power cords are not
energized.
Note
Ensure that there is a readily accessible disconnect device incorporated in the buildings installation
wiring.
Note
Circuit breaker and fuse lockout procedures should follow the rules and regulations in the National
Electrical Code (NEC) and any local codes.
1-47
Chapter 1
Figure 1-52 shows the lug type required for DC input cable connections.
Figure 1-52
Typical DC Power Cable Lug
.25 in +/- .04 in

(6.35 mm +/- 1.016 mm)
0.63 in +/- .02 in
(16 mm +/- 0.508 mm)
0.22 in
(5.588 mm)
0.31 in
(7.874 mm)
0.48 in +/- .04 in

(12.192 mm +/- 1.016 mm)
0.27 in +/- .02 in
(6.858 mm +/- .508 mm)
Beveled wire entry
0.81 in +/- .04 in

(20.574 mm +/- 1.016 mm)
1.16 in
(29.464 mm)
1.25 in +/- .04 in

(31.75 mm +/- 1.016 mm)
243275
90 degrees +/- 5 degrees

0.08 in +/- .01 in
(2.032 mm +/- 0.254 mm)
1.66 in (42.164 mm )
Note
Figure 1-53 shows typical DC power source cable connections for a version 1 single DC power
module, in this case, a module installed in slot M2 of the power tray.
Figure 1-55 shows the plastic safety cover for the version 2 and version 3 DC power tray connection
terminals.
The DC power trays and power modules for the Cisco ASR 9000 Series Routers are identical, so the
examples shown in Figure 1-53, Figure 1-54, Figure 1-55 and Figure 1-55 apply to all of these routers.
1-48
Chapter 1

Warning
Typical Source DC Power Cabling Scheme for a Single DC Power ModuleVersion 1 Power System
243183
Figure 1-53
To avoid shock hazard, be sure to apply shrink wrap tubing around the wire entry area of the lug.
PWR A
48/60V PWR
RTN A+
48/60V RTN
Feed A, Slot M2
PWR B
48/60V PWR
RTN B+
48/60V RTN
Ground
Feed B, Slot M2
1-49
Chapter 1
Figure 1-54
M3
M2
M1
M3
M2
344255
M1
PWR A
48/60V PWR RTN A+
48/60V RTN
Feed A, Slot M3
PWR B
48/60V PWR RTN B+
48/60V RTN
Feed B, Slot M3
Typical Plastic Safety Cover over the Power Tray Connection TerminalsVersion 2 and Version 3 Power
System
344357
Figure 1-55
1-50
Chapter 1

PWR A
48/60V PWR RTN A+
48/60V RTN
Feed A, Slot M3
PWR B
48/60V PWR RTN B+
48/60V RTN
Feed B, Slot M3
Note
364234
Figure 1-56
A separate ground connection is not required for the version 2 or version 3 power systems. For more
information see the NEBS Supplemental Unit Bonding and Grounding Guidelines, page 1-52.
The color coding of source DC power cable leads depends on the color coding of the site DC power
source. Because there is no color code standard for source DC wiring, be sure that power source cables
are connected to the power modules using the proper positive (+) and negative () polarity:
Caution
In some cases, the source DC cable leads might have a positive (+) or a negative () label. This is a
relatively safe indication of the polarity, but you must verify the polarity by measuring the voltage
between the DC cable leads. Be sure that the positive (+) and negative () cable leads match the
positive (+) and negative () labels on the power module when making the measurement.
Green (or green and yellow) cable typically indicates that it is a ground cable.
DC power modules contain reverse voltage protection circuitry to prevent damage to the power module
if it detects a reverse polarity condition. No damage should occur from reverse polarity, but you should
correct a reverse polarity condition immediately.
For a list of the nominal and acceptable value ranges for source DC power, see Appendix A.
1-51
Chapter 1
NEBS Supplemental Unit Bonding and Grounding Guidelines

Although the router chassis requires a safety earth ground connection as part of the power cabling to
power modules, you must permanently connect the central office ground system or interior equipment
grounding system to one of the three supplemental bonding and grounding connections on the back or
side of the router chassis to meet Network Equipment Building System (NEBS) requirements as well as
safety compliance requirements. These grounding points are referred to as the NEBS bonding and
grounding points.
Note
NEBS Bonding and Grounding Points on the Cisco ASR 9006 Router Chassis
243182
Figure 1-57
These bonding and grounding connections satisfy the Telcordia NEBS requirements for supplemental
bonding and grounding connections. If you are not installing the router in a NEBS environment, you can
choose to bypass these guidelines and rely on the safety earth ground connections to the AC or DC power
modules.
NEBS grounding point on

right side of the chassis
2 NEBS grounding point on

rear of the chassis
1-52
NEBS grounding point on

left side of the chassis
Chapter 1

Figure 1-58
NEBS Bonding and Grounding Point on the Cisco ASR 9006 Router Chassis
243373
NEBS grounding point on right

side of chassis
NEBS grounding point on left

side of the chassis
NEBS Bonding and Grounding Point on the Cisco ASR 9904 Router Chassis
390155
Figure 1-59
2 NEBS grounding point on rear

of the chassis
NEBS grounding point on right side of chassis
2 NEBS grounding point on rear of the chassis
1-53
Chapter 1
NEBS Bonding and Grounding Point on the Cisco ASR 9912 Router
344078
Figure 1-60
1
1
NEBS grounding point near bottom, rear, right side of the chassis
NEBS Bonding and Grounding Point on the Cisco ASR 9922 Router
303660
Figure 1-61
NEBS grounding point near bottom, rear, right side of the chassis
To ensure a satisfactory supplemental ground connection to the router, use the following parts:
Note
One grounding lug, which has two M6 bolt holes with 0.625- to 0.75-inch (15.86- to 19.05-mm)
spacing between them, and a wire receptacle able to accept a 2-6 AWG or larger, multistrand copper
wire. This lug is similar to those used for the DC input power supply leads (Figure 1-52).
Two 10-32 round-head screws and two locking washers (nickel-plated brass is ideal).
One grounding wire. Although we recommend at least 2-6 AWG multistrand copper wire, the wire
diameter and length depend on your router location and site environment.
These parts are not available from Cisco, but they are available from commercial vendors.
1-54
Chapter 1

RSP and RP Port Connection Guidelines

This section contains detailed cabling and signal information for interface and port connections to the
Route System Processor (RSP) or Route Processor (RP) cards. It also provides information for Ethernet
routing and equipment.
Note
The generic term RSP card refers to the RSP-440, RSP-440 Lite, and RSP-880 cards, unless otherwise
specified.
Caution
Ports labeled Ethernet, SYNC, CONSOLE, and AUX are safety extra-low voltage (SELV) circuits. SELV
circuits should only be connected to other SELV circuits.
Console Port and Auxiliary Port Connection Guidelines

Each RSP/RP card has two EIA/TIA-232 (formerly RS232) serial RJ-45 connection ports:
Console portRJ-45 interface for connecting a data terminal device to the router, which you need
to perform the initial configuration of the router.
Auxiliary portRJ-45 interface for connecting a modem.
Note
The console and auxiliary ports are asynchronous serial ports. Ensure that devices connected to
these ports are capable of asynchronous transmission.
For the console and auxiliary port locations, see Route Processor Overview, page 4-19.
1-55
Chapter 1
Console Port Signals

The console port is an RJ-45 interface for connecting a terminal to the router. The console port does not
support modem control or hardware flow control and requires a straight-through RJ-45 cable.
Before connecting a terminal to the console port, check the terminal setting for the data transmission
rate, in bits per second (bps). The terminal transmission rate setting must match the default rate of the
console port, which is 9600 bps. Set the terminal to these operational values: 9600 bps, 8 data bits, no
parity, 2 stop bits (9600 8N2).
Table 1-5 lists the signals used on the console port.
Table 1-5
RSP/RP Console Port Signals
Console Port Pin
Signal
Input/Output
Description
DTR
Output
Data Terminal Ready
TxD
Output
Transmit data
GND
Signal ground
GND
Signal ground
RxD
Input
Receive data
DSR
Input
Data Set Ready
Auxiliary Port Signals

The Auxiliary (AUX) port is an RJ-45 interface for connecting a modem or other data communication
equipment (DCE) device (such as another router) to the RSP/RP. The AUX port supports hardware flow
control and modem control.
Table 1-6 lists the signals used on the auxiliary port.
Table 1-6
RSP/RP AUX Port Signals
AUX Port Pin
Signal
Input/Output
Description
RTS
Output
Request to send
DTR
Output
Data terminal ready
TxD
Output
Transmit data
GND
Signal ground
GND
Signal ground
RxD
Input
Receive data
DSR
Input
Data set ready
CTS
Input
Clear to send
1-56
Chapter 1

Management LAN Ports Connection Guidelines

Each RSP/RP card has two RJ-45 media-dependent interface (MDI) Ethernet management LAN ports:
MGT LAN 0 and MGT LAN 1. These ports are used for IEEE 802.3u 100BASE-TX (100 Mbps), or
1000BASE-T (1000 Mbps) Ethernet connections. For the management port locations, see Route
Processor Overview, page 4-19.
The transmission speed of the management LAN ports is not user-configurable. The transmission speed
is set through an autosensing scheme on the RSP/RP; the speed is determined by the network that the
Ethernet port is connected to. The combined total input rate of both MGT LAN 0 and MGT LAN 1 is
about 12 Mbps.
Management port characteristics are:
Maximum transmission unit (MTU) is fixed at 1514 and cannot be configured.
Flow control is disabled and cannot be configured.
Input unicast packets with an unknown destination address are filtered and dropped.
Autonegotiation of port speed (100/1000) and duplex (full/half) is supported. Autonegotiation

cannot be disabled.
Table 1-7 lists the signals used on the Management LAN ports.
Table 1-7
RSP/RP Management LAN Port Signals
MGT LAN Port Pin
100Base-TX Signal
1000Base-T Signal
Transmit+
BI_DA+
Transmit
BI_DA
Receive+
BI_DB+
Unused
BI_DC+
Unused
BI_DC
Receive
BI_DB
Unused
BI_DD+
Unused
BI_DD
Management LAN Port LED Indicators

The Management LAN connectors have integral LED indicators (Figure 1-62). When lit, these LEDs
indicate:
Green (LINK)Connection is alive.
Amber (ACT)Connection is active.
1-57
Chapter 1
RSP/RP Management LAN Port LED Indicators
243165
Figure 1-62
Management LAN RJ-45 Cabling

When connecting the RJ-45 port to a hub, repeater, or switch, use the straight-through cable pinout as
shown in Figure 1-63.
To comply with the intrabuilding lightning surge requirements of Telecordia GR-1089-CORE, Issue II,
Revision 01, February 1999, you must use a shielded cable when connecting to the management LAN
ports on the RSP/RP card. The shielded cable is terminated by shielded connectors on both ends, with
the cable shield material tied to both connectors.
Figure 1-63
Straight-Through Cable Pinout to a Hub, Repeater or Switch
MDI wiring
MDI-X wiring
1 TxD+
1 RxD+
2 TxD
2 RxD
3 RxD+
3 TxD+
6 RxD
6 TxD
H11007
Note
When connecting the RJ-45 port to a router, use the crossover cable pinout as shown in Figure 1-64.
Crossover Cable Pinout Between RSPs/RPs
PRP
PRP
1 TxD+
1 TxD+
2 TxD
2 TxD
3 RxD+
3 RxD+
6 RxD
6 RxD
75431
Figure 1-64
1-58
Chapter 1

Alarm Connection Guidelines

The RSP/RP card has an alarm connector on its front panel. This 9-pin D-subconnectors (ALARM OUT)
connects the router to an external site alarm maintenance system (Figure 1-65). When a critical, major,
or minor alarm is generated, it energizes the alarm relays on the RSP/RP card to activate the external site
alarm.
Figure 1-65
8
7
6
5
4
3
2
1
243085
Alarm Connector on the RSP/RP Card Front Panel
The alarm relay contacts on the RSP/RP card consist of standard common, normally open, and normally
closed relay contacts that are wired to the pins on the connectors.
Caution
Only safety extra-low voltage (SELV) circuits can be connected to the alarm connector. Maximum rating
for the alarm circuit is 100 mA, 50 V.
Note
To comply with the intrabuilding lightning surge requirements of Telecordia GR-1089-CORE, Issue II,
Revision 01, February 1999, you must use a shielded cable when connecting to the external alarm port
on the RSP/RP card. The shielded cable is terminated by shielded connectors on both ends, with the
cable shield material tied to both connectors.
1-59
Chapter 1
Table 1-8 lists the pin-to-signal correspondence between the cable connector pins and the alarm
connector relay contacts.
Table 1-8
Pin
Alarm Connector Pinout
Signal
Note
Critical alarm NC
NC (normally closed) connected to CM (common) when

there is no Critical alarm
Critical alarm CM
Common
Critical alarm NO
NO (normally open) connected to CM (common) during a

Critical alarm
Major alarm NC

there is no Major alarm
Major alarm CM
Common
Major alarm NO

Major alarm
Minor alarm NC

there is no Minor alarm
Minor alarm CM
Common
Minor alarm NO

Minor alarm
Sync Port Connection Guidelines

The SYNC 0 and SYNC 1 ports are timing synchronization ports. They can be configured as Building
Integrated Timing Supply (BITS) ports or J.211 ports (Figure 1-66).
Note
Both ports must be configured to be the same mode. It is not possible to use external BITS and J.211
sources at the same time.
When configured as BITS ports, they provide connections for an external synchronization source for
establishing precise frequency control at multiple network nodes, if required for your application. The
RSP/RP card contains a synchronous equipment timing source (SETS) that can receive a frequency
reference from an external BITS timing interface or from a clock signal recovered from any incoming
Gigabit Ethernet or 10-Gigabit Ethernet interface. The RSP/RP SETS circuit filters the received timing
signal and uses it to drive outgoing Ethernet interfaces.
The BITS input can be T1, E1 or 64K 4/. The BITS output can be T1, E1 or 6.312M 5/.
When configured as J.211 ports, they can be used as Universal Timing Interface (UTI) ports to
synchronize timing across multiple routers by connecting to an external timing source.
When lit, these LEDs indicate for BITS:
Green (LINK)Connection is alive.
Amber (FAULT)A fault has occurred.
1-60
Chapter 1

When lit, these LEDs indicate for UTI:
Green (NORMAL)UTI is operating in normal mode.
Amber (FAST)UTI is operating in fast mode.
Figure 1-66
SYNC Port Connector
243166
12345678
Table 1-9
Pin
BITS/J.211 Connector Pinout
Signal
Note
DTI_P/BITS_RX_P
Bi-direction for DTI, T1/E1/64K Input
DTI_P/BITS_RX_N
Bi-direction for DTI, T1/E1/64K Input
BITS_TX_P*
T1/E1/6.321M Output
BITS_TX_N*
T1/E1/6.321M Output
SFP/SFP+ Port
The RSP-440 and RSP-440 Lite support two 10-GE Small Form-Factor Pluggable Plus (SFP+)
virtualization cluster ports. The RSP-880 supports four 10-GE SFP+ ports that are used for external
server connectivity capability.
GPS Interface
The RSP-440, RSP-440 Lite, and RSP-880 have a Time of Day (ToD) port, 10-MHz connector, and
1-PPS connector that allow you to configure input or output clocking with a GPS device.
Inter Chassis Synchronization Port

The nV Sync 0 and nV Sync 1 ports on the RSP-440, RSP-440 Lite, and RSP-880 are the RJ-45
inter-chassis synchronization clock interfaces for synchronizing frequency and time.
1-61
Chapter 1
CMP Port
The Connectivity Management Processor (CMP) on the RSP-440, RSP-440 Lite, and RSP-880 card, is
a secondary, lightweight processor that provides a second network interface to the system. Each CMP
contains its own RAM, bootflash, and front panel management Ethernet port.
The CMP port provides the following functions:
RSP4 ROMMON console access through the CMP port. This eliminates the need to use external
terminal servers.
SSH/telnet into a designated CMP port.
RSP Compact Flash Slot

The Cisco ASR 9000 Series Router RSP cards support a single ATA/IDE type I/II compact flash external
slot accessible on the front panel. The compact flash slot has a door that can be closed whether a compact
flash device is present or not. The file systems supported on compact flash are DOS/FAT or QNX4. The
compact flash comes with a DOS format. The supported flash disk sizes and their Cisco part numbers
are listed in Table 4-5.
The RSP-440, RSP-440 Lite, and RSP-880 cards do not have an ATA/IDE type I/II compact flash external
slot.
USB Port
The RSP-440, RSP-440 Lite, RSP-880, and Cisco ASR 9922 Router RP cards have a single external
Universal Serial Bus (USB) port. A USB flash memory device can be inserted to load and transfer
software images and files. This memory device can be used to turboboot the system or as the installation
source for Package Information Envelopes (PIE) and Software Maintenance Upgrades (SMU). This
memory device can also be used for users' data files, core files, and configuration backups.
1-62
CH A P T E R

This chapter describes how to unpack and install the chassis into a rack.
Pre-Installation Considerations and Requirements, page 2-1
Installation Overview, page 2-2
Unpacking the Router, page 2-3
Removing Components Before Installing the Chassis, page 2-18
Rack-Mounting the Router Chassis, page 2-42
Supplemental Bonding and Grounding Connections, page 2-56
Installing Chassis Accessories, page 2-61
Pre-Installation Considerations and Requirements

Before you perform any procedures in this chapter, review the following sections:
Safety Guidelines, page 1-1
Site Requirement Guidelines, page 1-8
Observe the guidelines for preventing electrostatic discharge (ESD) damage described in the Preventing
Electrostatic Discharge Damage section on page 1-2.
See the Regulatory Compliance and Safety Information for the Cisco ASR 9000 Series Router document
for additional safety and compliance information,
Caution
This router is not designed to be installed as a shelf-mounted or a free-standing router. The router must
be installed in a rack that is secured to the building structure. You must install the router in either a
telco-style frame or a 4-post equipment rack.
2-1
Chapter 2
Installation Overview
Installation Overview
Figure 2-1 shows how the Cisco ASR 9010 Router is shipped and strapped to a shipping pallet.
Cisco ASR 9010 Router Packaged on a Shipping Pallet
243355
Figure 2-1
A fully equipped router with six power modules can weigh as much as 375 lbs (170.5 kg); an empty
chassis weighs 150 lbs (67.8 kg). The chassis is designed to be lifted by two persons after you remove
some of the components, such as line cards, power supplies, and the fan tray, to reduce the weight before
lifting the chassis. See Removing Components Before Installing the Chassis, page 2-18 for procedures
to remove these components.
2-2
Chapter 2

Unpacking the Router

Before you begin the rack-mount installation, you must read and understand the information in the
Rack-Mounting and Air Flow Clearance Guidelines, page 1-20, and have the following tools and
equipment:
ESD-preventive wrist strap
Number 1 and number 2 Phillips screwdrivers
1/4-inch (6.35-mm) and 3/16-inch (4.5-mm) flat-blade screwdrivers
Tape measure
Level (optional)
Minimum of 10 slotted binderhead screws (usually provided with the rack) to secure the chassis to
the mounting flanges (also called rails) in the rack. Five screws should be installed on each side of
the chassis.
11/16-inch (17.46-mm) wrench (for chassis hold-down bolts and pallet hold-down bracket bolts)
3/4-inch (19-mm) socket and ratchet wrench

The following instructions describe how to unpack the Cisco ASR 9000 Series Router from its shipping
container.
Unpacking the Cisco ASR 9010 Router, page 2-3
Unpacking the Cisco ASR 9010 Router

Follow these steps to unpack the Cisco ASR 9010 Router from its shipping container.
Step 1
Cut the straps that secure the cardboard shipping container to the pallet.
Step 2
Remove the cardboard shipping container.
Step 3
Remove the packaging material (see Figure 2-2).
Step 4
a.
Remove the foam packaging material from the top of the router.
b.
Remove all screws that secure the four hold-down brackets to the router chassis. The forward
hold-down brackets are secured to the router mounting brackets by two screws. The rear hold-down
brackets are secured to the chassis by four screws. Save these four screws used to hold the rear
bracket to the chassis to use later to attach the ground strap.
Remove two bolts per hold-down bracket that secure the brackets to the pallet.
2-3
Chapter 2
Figure 2-2
Unpacking the Cisco ASR 9010 Router from the Shipping Container and Pallet
MGT LAN 0
MGT LAN 0
ACT
ACT
MGT LAN 1
MGT LAN 1
LINK
LINK
CONSOLE
CONSOLE
BITS
BITS
0
J.211
J.211
BITS
BITS
1
J.211
J.211
ALARM OUT
ALARM OUT
ACO
ACO
LAMP
TEST
FAIL
LAMP
TEST
SYNC
FAIL
CRIT
SYNC
HDD
CRIT
CF
MIN
ACO
HDD
MAJ
CF
MIN
ACO
243356
MAJ
2
2
Foam packaging materialtop cap
Front hold-down bracket

secured by two screws to the
chassis mounting brackets,
and by two bolts to the
pallet (two places)
Rear hold-down bracket

secured by four screws to the
chassis, and by two bolts to
the pallet (two places)
Step 5
Remove components, such as line cards and the fan tray, to reduce the weight before lifting or moving
the chassis. See the Removing Components Before Installing the Chassis, page 2-18 for more
information.
Step 6
Save the packaging materials in case the router needs repackaging or shipping.
2-4
Chapter 2


Follow these steps to unpack the Cisco ASR 9006 Router from its shipping container (Figure 2-3).
Step 1
Step 2
Remove the cardboard shipping container.
Step 3
Remove the packaging material (Figure 2-3).

a.
b.
Remove all screws that secure the four hold-down brackets to the router chassis. The forward
hold-down brackets are secured to the router mounting brackets by two screws. The rear hold-down
brackets are secured to the chassis by four screws.
c.
Remove two bolts per hold-down bracket that secure the brackets to the pallet.
2-5
Chapter 2
Figure 2-3
4
7
243454
Top cardboard packaging

cap
Cardboard packaging
container
Chassis accessories
Three packaged power

modules
Cardboard accessory tray
Foam packaging materialtop cap
Cardboard packaging
dividers
Accessories and power

cables
Hold-down brackets
(four places)
2-6
Chapter 2

Step 4
Remove components, such as line cards, power supplies, and the fan tray, to reduce the weight before
lifting or moving the chassis. See Removing Components Before Installing the Chassis, page 2-18 for
more information.
Step 5

Follow these steps to unpack the Cisco ASR 9904 Router from its wooden shipping container.
Step 1
Step 2
Remove the corrugated top shipping container.
Step 3
Remove the accessories and corrugated packing accessory tray.
Step 4
Remove the packing material (Figure 2-4).

a.
b.
Remove the plastic covering from the router and remove it from the bottom foam.
2-7
Chapter 2
Figure 2-4
5
351310
Shipping pallet
Foam packaging material

(top cap)
Top corrugated packaging cap
Foam packaging material

(bottom cap)
Corrugated packaging
accessory tray
Corrugated packaging
(lower tray)
Cardboard shipping
container
Step 5
Remove components, such as line cards, power supplies, and the fan tray, to reduce the weight before
lifting or moving the chassis. See Removing Components Before Installing the Chassis, page 2-18 for
more information.
Step 6
2-8
Chapter 2


Step 1
Remove any strapping on the outside of the crate.
Step 2
Remove the crate cap door. Disengage the twist locks located along the bottom first. Then, disengage the
twist locks located along the sides, working your way up from the bottom to the top. Refer to the right
and middle figures in Figure 2-5.
Step 3
Remove the crate cap. Disengage the twist locks located around the bottom of the crate cap (Figure 2-5).
Note
Step 4
Unpacking the Cisco ASR 9922 Router from the Shipping Container
302353
Figure 2-5
Two people are required to evenly slide the crate cap back off of the plastic pallet base.
Step 5
Using a 5/16 wrench or ratchet, remove the four attachment bolts and cross-brace from the shipping
rack (Figure 2-6).
2-9
Chapter 2
Cross-brace and Attachment Bolts on the Shipping Rack
344358
Figure 2-6
2-10

Step 6
Use a Phillips screwdriver to unscrew the rear mounting flange from the system and rack.
Step 7
Use a Phillips screwdriver to unscrew the front mounting flange from the rack.
Step 8
Remove two bolts per hold-down bracket that secure the brackets to the pallet (Figure 2-7).
Figure 2-7
Hold-Down Brackets on the Cisco ASR 9922 Router Shipping Pallet
302355
Chapter 2
Note
Step 9
Do not unbolt the shipping rack from the pallet.
Save the rear brackets and screws from the shipping packaging for reuse in rack mounting of the chassis
(Figure 2-8).
Note
The two guide rails at the bottom of the rack come in the ASR-9922-ACC-KIT accessory kit.
2-11
Chapter 2
Rack Mount Installation Kit for the Cisco ASR 9922 Router
344377
Figure 2-8
Step 10
Remove components, such as line cards and fan trays, to reduce the weight before lifting or moving the
chassis. See Removing Components Before Installing the Chassis, page 2-18 for procedures showing
how to remove these components.
Step 11
Save the packaging materials in case the router needs to be repackaged for shipping.
2-12
Chapter 2


Step 1
Remove any strapping on the outside of the crate.
Step 2
Remove the crate cap door. Disengage the twist locks located along the bottom first. Then, disengage the
twist locks located along the sides, working your way up from the bottom to the top. Refer to the right
and middle figures in Figure 2-9.
Step 3
Remove the crate cap. Disengage the twist locks located around the bottom of the crate cap (Figure 2-9).
Note
Step 4
Unpacking the Cisco ASR 9912 Router from the Shipping Container
302353
Figure 2-9
Two people are required to evenly slide the crate cap back off of the plastic pallet base.
Step 5
Using a 5/16 wrench or ratchet, remove the four attachment bolts and cross-brace from the shipping
rack (Figure 2-10).
2-13
Chapter 2
Cross-brace and Attachment Bolts on the Shipping Rack
344358
Figure 2-10
2-14

Step 6
Use a Phillips screwdriver to unscrew the rear mounting flange from the system and rack.
Step 7
Use a Phillips screwdriver to unscrew the front mounting flange from the rack.
Step 8
Remove two bolts per hold-down bracket that secure the brackets to the pallet (Figure 2-11).
Figure 2-11
Hold-Down Brackets on the Cisco ASR 9912 Router Shipping Pallet
302355
Chapter 2
Note
Step 9
Do not unbolt the shipping rack from the pallet.
Save the rear brackets and screws from the shipping packaging for reuse in rack mounting of the chassis
(Figure 2-12).
Note
The two guide rails at the bottom of the rack come in the ASR-9912-ACC-KIT accessory kit.
2-15
Chapter 2
Rack Mount Installation Kit for the Cisco ASR 9912 Router
344377
Figure 2-12
Step 10
Remove components, such as line cards and fan trays, to reduce the weight before lifting or moving the
chassis. See Removing Components Before Installing the Chassis, page 2-18 for procedures showing
how to remove these components.
Step 11
Save the packaging materials in case the router needs to be repackaged for shipping.
2-16
Chapter 2

Positioning the Router

Positioning the Cisco ASR 9010 Router, Cisco ASR 9006 Router, and Cisco 9904 Router
Use a safety hand truck to move the Cisco ASR 9010 Router, Cisco ASR 9006 Router, or
Cisco ASR 9904 Router router to its final location for rack installation.
Positioning the and Cisco ASR 9922 Router and Cisco ASR 9912 Router
TheCisco ASR 9922 Router and Cisco ASR 9912 Router and each ship in a carton similar to the CRS-1
16-Slot shipping carton. Each chassis is installed in a shipping rack used only for shipping purposes.
Remove the chassis from the shipping rack before installing it into the rack.
To prepare the 19-inch 45-RU rack:
Step 1
Install the two guide rails onto the bottom of the rack.
The guide rails are included with the ASR-9922-ACC-KIT and ASR-9912-ACC-KIT accessory kits.
Each accessory kit ships with the chassis and includes the guide rails, grounding lug, associated
hardware, and a warranty card.
Step 2
Use screws to fasten these two guide rails onto the front and rear rails of the rack.
The two guide rails at the bottom of the rack (Figure 2-8) have six holes (three per rail) that
accommodate 12-24 or M6 screws. If you are using smaller 10-32 screws, you must use bushings to fit
the larger holes (Figure 2-13).
One 10-32 Screw with Bushings in Guide Rail Holes
303498
Figure 2-13
Note
Step 3
Delrin bushings with part number 17234-D-1 can be obtained from ASM at
www.accuratescrew.com.
Remove the shipping carton, plastic covering, rear brackets, attachment screws and bolts, shipping rack
bar, and any cosmetic accessories included with the chassis.
2-17
Chapter 2
Removing Components Before Installing the Chassis
Step 4
Use a scissors jack to remove the chassis from the shipping rack. Place a pallet jack next to the chassis
inside the shipping rack and push/pull the chassis onto the pallet jack for transport to the rack.
Caution
Tilt the chassis only when absolutely necessary. The chassis is large and heavy. If it were to fall, it could
cause harm to itself and its surroundings. Before attempting to tilt the chassis, reduce the weight of the
system by removing all of the components in the chassis. The chassis should then be tilted in a direction
so that the rear of the chassis is facing downward. The distance the chassis travels without its packaging
should be as short as possible.
Step 5
On the rear of the chassis is an integrated handle which is used to pull the chassis from the pallet jack
into the rack where the chassis is to be installed. Position the chassis so that the rear handle is facing the
front of the rack.
Step 6
From the rear of the rack, pull the chassis by the handle into the rack, making sure that the chassis sits
on top of the guide rails in the rack.
Step 7
Once the chassis is pulled into the rack and sits on top of the guide rails, use screws to fasten the chassis
to the rack.

The Cisco ASR 9000 Series Routers are designed to be lifted for mounting into a rack. To reduce the
weight of the system, you must remove some of the components before attempting to mount it into the
rack.
Removing Power Modules, page 2-18
Removing Fan Trays, page 2-18
Removing Cards from the Chassis, page 2-23
Removing Power Modules

The power modules for the Cisco ASR 9000 Series Routers are shipped separately. If you need to
remove an AC or DC power module at a later time, see Removing and Replacing Power System
Components, page 5-12.
Removing Fan Trays

Note
If an accessory grill or fan tray cover is installed on the front of the router, you must remove it first.
Removing a Fan Tray from the Cisco ASR 9010 Router, Cisco ASR 9922 Router, and Cisco ASR 9912
Router
Follow these steps to remove a fan tray from the Cisco ASR 9010 Router (Figure 2-14), Cisco ASR 9922
Router (Figure 2-15), or Cisco ASR 9912 Router (Figure 2-16).
2-18

Note
If an accessory grill is installed on the front of the Cisco ASR 9010 Router, remove the grill by pulling
it towards you until it comes loose. See Installing Base Chassis Accessories on the
Cisco ASR 9010 Router, page 2-61 and Figure 2-56 for information.
Note
If a fan tray cover is installed on the front of the Cisco ASR 9922 Router, remove the fan tray cover by
pulling on the cover until it comes loose. See Installing Optional Chassis Accessories on the
Cisco ASR 9922 Router, page 2-91 for more information.
Note
On the Cisco ASR 9922 Router, the third and fourth fan trays (under the middle cage) are installed upside
down compared to the first and second fan trays (above the middle cage).
Step 1
Loosen the captive screw on each side of the fan tray.
Step 2
Using the handle on the front panel, pull the fan tray halfway out of the chassis.
Note
Step 3
Caution
Wait a few seconds for all the fans to stop rotating before lifting the fan tray from the chassis.
Slide out the fan tray completely from the chassis while supporting it with your other hand.
Use two hands when handling the fan tray. Each version 1 fan tray weighs about 16 pounds (7.27 kg).
Each version 2 fan tray weighs about 18 pounds (8.18 kg).
Figure 2-14
Removing or Installing the Fan Tray on the Cisco ASR 9010 Router Chassis
243179
Chapter 2
2-19
Chapter 2
Figure 2-16
303663
344040
Figure 2-15
2-20
Chapter 2

Removing a Fan Tray from the Cisco ASR 9006 Router

Follow these steps to remove a fan tray from the Cisco ASR 9006 Router (Figure 2-17).
Step 1
Loosen the captive screw that secures the fan tray door to the chassis and open the door.
Step 2
Loosen the captive installation screw on the front of the fan tray you want to remove.
Step 3
Note
Step 4
Caution
Use two hands when handling the fan tray. The fan tray weighs about 7.6 pounds (3.45 kg).
243374
Figure 2-17
2-21
Chapter 2
Removing a Fan Tray from the Cisco ASR 9904 Router

Follow these steps to remove a fan tray from the Cisco ASR 9904 Router (Figure 2-18).
Step 1
Loosen the three captive installation screws on the front of the fan tray.
Step 2
Step 3
Step 4
Caution
Use two hands when handling the fan tray. The fan tray weighs about 11.0 pounds (4.99 kg).
351299
Figure 2-18
2-22
Chapter 2

Removing Cards from the Chassis

To reduce additional weight from the chassis, you can remove all Route Switch Processor (RSP), Route
Processor (RP), Switch Fabric Card (FC), shared port adapter (SPA), SPA interface processor (SIP), and
line cards (LCs).
This section describes how to remove the RSP cards, RP cards, FCs, and LCs. For information about
removing SPA and SIP cards, see:
Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide
Caution
Handle all cards by the metal card carrier edges only; avoid touching the board or any connector pins.
After removing a card, carefully place it in an antistatic bag or similar environment to protect it from
ESD and dust in the optic ports (fiber-optic line cards).
Caution
Be careful to avoid damaging the electromagnetic interference (EMI) gasket that runs along the full
height of the card front panel edge. Damage to the EMI gasket can affect the ability of your system to
meet EMI requirements.
Caution
To avoid damaging card mechanical components, never carry a card by the captive installation screws or
ejector levers. Doing so can damage these components and cause card insertion problems.
Removing RSP Cards and Line Cards from the Cisco ASR 9010 Router, Cisco ASR 9006 Router, and
Cisco ASR 9904 Router
This section describes how to remove RSP and line cards from the Cisco ASR 9010 Router,
Cisco ASR 9006 Router, and Cisco ASR 9904 Router. Table 2-1 and Table 2-2 describe the router
components and slot numbering for each router.
2-23
Chapter 2
Table 2-1
Router Components and Slot Numbering for the Cisco ASR 9010 Router, Cisco ASR 9006 Router, and
Router Model Number

Router Components and Slot Numbering
10 slots.
Version 1 power system (Figure 2-19), Version 2 power system (Figure 2-20), or Version
3 power system (Figure 2-19 for AC and Figure 2-20 for DC).
Two RSP cards installed in the two center slots (labeled RSP0 and RSP1).
Four line cards installed in slots 0 through 3 to the left of the RSP card slots.
Four line cards installed in slots 4 though 7 to the right of the RSP card slots.
6 slots.
Version 1 power system (Figure 2-21) or Version 2 power system (Figure 2-22).
Two RSP cards installed in the two lowest slots (labeled RSP0 and RSP1) located above
the power modules.
Four line cards installed in slots 2 through 5 above the RSP card slots.
4 slots.
Version 2 power system (Figure 2-21).
One line card installed in the top slot (labeled LC1). Two RSP cards installed in the
middle two slots (labeled RSP1 and RSP0) located between the line cards (LC0 and
LC1).
One line card installed in the lowest slot (LC0) located above the power modules.
2-24

Figure 2-19
Cisco ASR 9010 Router Components and Slot Numbering with Version 1 Power
System or Version 3 AC Power System
RSP cards
Line cards 0-3
Line cards 4-7
Line card
Line card
Line card
RSP0
RSP1
Line card
Line card
Line card
Line card
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Slot 6
Slot 7
Slot 8
Slot 9
4 5 6 7
Line card
0 1 2 3
Slot 0
FT0
Fan trays
FT1
Front air intake
Power shelves
PS0
M0
M1
M2
PS1
M0
M1
M2
242689
Chapter 2
Power modules
2-25
Chapter 2
Figure 2-20
System or Version 3 DC Power System
RSP cards
e cards 0-3
Line cards 4-7
RSP0
RSP1
Line card
Line card
Slot 4
Slot 5
Slot 6
Slot 7
Line card
Line card
Slot 3
Line card
Line card
Slot 2
Slot 9
Line card
Slot 8
Line card
Slot 1
4 5 6 7
Slot 0
0 1 2 3
FT0
Fan trays
FT1
wer shelves
PS0
M0
M1
M2
M3
PS1
M0
M1
M2
M3
284401
Front air intake
Power modules
Figure 2-21
System
Fan trays
Line cards
RSP cards
Power shelf
FT1
Slot 5
Slot 4
Slot 3
Slot 2
Slot 1
Slot 0
M0
Line card 3
Line card 2
Line card 1
Line card 0
RSP1
RSP0
M1
M2
Power modules
2-26
243377
FT0

Figure 2-22
System
Fan trays
Slot 5
Slot 4
Slot 3
Slot 2
Slot 1
Slot 0
Line cards
RSP cards
Power shelf
M0
Line card 3
Line card 2
Line card 1
Line card 0
RSP1
RSP0
M1
M2
284273
FT0 FT1
M3
Power modules
Figure 2-23
System
Line card 1
RSP cards
Line card 0
Power shelf
M0
Slot 3
Line card 1
Slot 2
RSP1
Slot 1
RSP0
Slot 0
Line card 0
M1
M2
351300
Chapter 2
M3
Power modules
2-27
Chapter 2
Follow these steps to remove RSP and line cards from the chassis.
Step 1
Use Figure 2-24, Figure 2-25, or Figure 2-26 to identify each card and write down the card type and slot
number on a piece of paper. You will need this information when you reinstall the cards in the chassis to
be sure you reinstall each card in its original slot.
Step 2
To remove a card starting at the lowest numbered slot:

a.
Use a screwdriver to loosen the captive screws at the ends of the line card front panel.
b.
Pivot the ejector levers to unseat the card from the backplane connector.
c.
Slide the card out of the slot and place it directly into an antistatic bag or other ESD-preventive
container.
Figure 2-24
Removing a Line Card from the Cisco ASR 9010 Router Chassis
Loosen the captive screws.
Pivot the ejector levers to

unseat the card from the
backplane connector.
2-28
Slide the card out of the

chassis.
Chapter 2

Figure 2-25
243405

unseat the card from the

chassis.
2-29
Chapter 2
Figure 2-26
a
b
Step 3
Pivot the ejector levers to unseat

the card from the backplane
connector.
Repeat Step 2 for each RSP or line card.
2-30

chassis.
Chapter 2

Removing RP Cards, Fabric Cards, and Line Cards from the Cisco ASR 9922 Router and Cisco ASR
9912 Router
This section describes how to remove the Route Processor (RP) cards, Fabric Card (FC), and Line Cards
(LCs) from the Cisco ASR 9922 Router and Cisco ASR 9912 Router. Table 2-2 describes the
components and slot numbering for each router.
Table 2-2
Router Components and Slot Numbering for the Cisco ASR 9922 Router and Cisco ASR 9912 Router
Router Model Number

Router Components and Slot Numbering
22 slots.
Version 2 or version 3 power system. See Figure 2-27 for version 2 DC and Figure 2-28 for
version 3 DC. See Figure 2-29 for version 2 AC and Figure 2-30 for version 3 AC.
Up to seven FC cards installed between the two RSP cards in the middle cage of the chassis.
Ten line cards installed in slots 0 through 9 in the top card cage.
Ten line cards installed upside down in slots 10 through 19 in the bottom card cage.
12 slots.
Version 2 or version 3 power system, See Figure 2-31 for version 2 DC or version 3 power
systems (Figure 2-31 for DC and Figure 2-32 for AC).
Up to seven FC cards installed between the two RP cards above the power trays.
Ten line cards installed in slots 0 through 9 below the fan trays.
2-31
Chapter 2
Figure 2-27
Cisco ASR 9922 Router Components and Slot Numbering with Version 2 DC Power
System
PS3
M0
M1
M2
M3
Slot 8
Slot 7
Slot 6
FC5
FC6
RP1
Slot 16
Slot 17
Slot 18
Slot 19
LC14
LC15
LC16
LC17
LC18
LC19
FC4
Slot 15
LC13
FC2
Slot 14
LC12
FC1
Slot 13
FC0
Slot 12
LC10
LC11
RP0
Slot 10
Slot 11
FT2
FT3
Fan trays
302423
Line cards
Slot 5
FT0
FT1
Fan trays
FC3
Line cards
Slot 9
M3
LC8
M2
LC7
M1
LC6
M0
LC5
PS2
LC4
M3
Slot 4
M2
LC3
M1
LC2
M0
Slot 3
PS1
Slot 2
M3
LC1
M2
LC0
M1
Slot 1
M0
Slot 0
Power shelves/trays
PS0
LC9
Power modules
2-32

Figure 2-28
System
PS3
M0
M1
M2
M3
Slot 8
Slot 7
Slot 6
FC5
FC6
RP1
Slot 15
Slot 16
Slot 17
Slot 18
Slot 19
LC13
LC14
LC15
LC16
LC17
LC18
LC19
FC4
Slot 14
LC12
FC2
Slot 13
FC1
Slot 12
LC10
LC11
FC0
Slot 10
Slot 11
FT2
FT3
364249
Fan trays
Line cards
Slot 5
FT0
FT1
Fan trays
FC3
Line cards
LC8
M3
Slot 9
M2
LC7
M1
LC6
M0
LC5
PS2
LC4
M3
LC3
M2
Slot 4
M1
Slot 3
M0
LC2
PS1
LC1
M3
Slot 2
M2
Slot 1
M1
LC0
M0
Slot 0
Power shelves/trays
PS0
LC9
Power modules
RP0
Chapter 2
2-33
Chapter 2
Figure 2-29
Cisco ASR 9922 Router Components and Slot Numbering with Version 2 AC Power
System
Power modules
M2
M15
Slot 9
Slot 8
Slot 7
Slot 6
FC5
FC6
RP1
Slot 16
Slot 17
Slot 18
Slot 19
LC14
LC15
LC16
LC17
LC18
LC19
FC4
Slot 15
LC13
FC2
Slot 14
FC1
Slot 13
LC12
FC0
Slot 12
LC10
LC11
RP0
Slot 10
Slot 11
FT2
FT3
Fan trays
363713
Line cards
Slot 5
FT0
FT1
Fan trays
FC3
Line cards
LC9
M13 M1 M14
LC8
M0
M12
LC7
PS3
LC6
M2
M11
LC5
M9 M1 M10
LC4
M0
M8
LC3
PS2
Slot 4
M2
M7
Slot 3
M5 M1 M6
LC2
M0
M4
LC1
PS1
Slot 2
M2
M3
Slot 1
M1 M1 M2
LC0
M0
M0
Slot 0
Power shelves/trays
PS0
2-34

Figure 2-30
System
Power modules
M2
M15
Slot 9
Slot 8
Slot 7
Slot 6
FC5
FC6
RP1
Slot 15
Slot 16
Slot 17
Slot 18
Slot 19
LC13
LC14
LC15
LC16
LC17
LC18
LC19
FC4
Slot 14
LC12
FC2
Slot 13
FC1
Slot 12
LC10
LC11
FC0
Slot 10
Slot 11
FT2
FT3
364248
Fan trays
Line cards
Slot 5
FT0
FT1
Fan trays
FC3
Line cards
LC9
M13 M1 M14
LC8
M0
M12
LC7
PS3
LC6
M2
M11
LC5
M9 M1 M10
LC4
M0
M8
LC3
PS2
Slot 4
M2
M7
Slot 3
M5 M1 M6
LC2
M0
M4
LC1
PS1
Slot 2
M2
M3
Slot 1
M1 M1 M2
LC0
M0
M0
Slot 0
Power shelves/trays
PS0
RP0
Chapter 2
2-35
Chapter 2
System
M1
M2
M3
PS1
M0
M1
M2
M3
PS2
M0
M1
M2
M3
LC9
Slot 9
RP1
LC8
Slot 8
FC6
LC6
Slot 6
Slot 7
LC5
Slot 5
M0
Power modules
2-36
FC5
LC4
Slot 4
FC4
LC3
Slot 3
FC2
LC2
Slot 2
FC1
LC1
FC0
PS0
303672
Power shelves/trays
Slot 1
LC0
RP0
Slot 0
Line cards
LC7
FT0
FT1
Fan trays
(rear instertion)
FC3
Figure 2-31

System
LC9
Slot 9
RP1
LC8
Slot 8
LC6
Slot 6
Slot 7
LC5
Slot 5
FC6
FC5
LC4
Slot 4
FC4
LC3
Slot 3
FC2
LC2
Slot 2
FC1
LC1
FC0
LC0
PS0
M0
M0
M1 M1 M2
M2
M3
PS1
M0
M4
M5 M1 M6
M2
M7
PS2
M0
M8
M9 M1 M10
M2
M11
363712
Power shelves/trays
Slot 1
Slot 0
Line cards
LC7
FT0
FT1
Fan trays
(rear instertion)
FC3
Figure 2-32
RP0
Chapter 2
Power modules
Follow these steps to remove RP cards, FCs, and LCs from the Cisco ASR 9922 Router and
Cisco ASR 9912 Router chassis.
Step 1
Use Figure 2-27 or Figure 2-31 to identify each card and then write down the card type and slot number
on a piece of paper. You will need this information when you reinstall the cards in the chassis to be sure
you reinstall each card in its original slot.
Step 2
To remove a FC card (Figure 2-33 or Figure 2-34), starting at the lowest numbered slot:
a.
Remove the air filter covering the front of the middle cage.
b.
Use a screwdriver to loosen the captive screws at the ends of the FC front panel.
c.
Push in both ejector lever release buttons.
Note
d.
Once any ejector lever release button is pushed in, the FC must by physically removed and
reinserted (OIR) to restart the FC.
Pivot the ejector levers to unseat the FC from the backplane connector.
2-37
Chapter 2
e.
Slide the FC out of the slot and place it directly into an antistatic bag or other ESD-preventive
container.
Removing a Switch Fabric Card from the Cisco ASR 9922 Router Chassis
302424
Figure 2-33
Pivot the ejector levers outward to unseat the card

from the backplane connector.
Push in both ejector lever release buttons.
Slide the card out of the chassis.
2-38
Chapter 2

Figure 2-34
Removing a Switch Fabric Card from the Cisco ASR 9912 Router Chassis
a
b
c
d
b
a
c
Step 3
Pivot the ejector levers outward to unseat the card from the
Push in both ejector lever

release buttons.
Slide the card out of the chassis.
To remove a RP or line card (Figure 2-35 or Figure 2-36), starting at the lowest numbered slot:
a.
Use a screwdriver to loosen the captive screws at the ends of the line card front panel.
b.
c.
container.
2-39
Chapter 2
Figure 2-35
Removing a Line Card from the Cisco ASR 9922 Router Top Card Cage
344076
Pivot the ejector levers

outward to unseat the card
from the backplane
connector.
2-40

chassis.

Figure 2-36
Removing a Line Card from the Cisco ASR 9912 Router Top Card Cage
1
2
303664
Chapter 2
Step 4
Pivot the ejector levers

outward to unseat the card
from the backplane
connector.

chassis.
Repeat Step 2 or Step 3 for each FC, LC, and RP card.
2-41
Chapter 2
Rack-Mounting the Router Chassis

The router chassis is installed in a front-mounted position, as shown in Figure 1-18 for the Cisco ASR
9010 Router, Figure 1-19 for the Cisco ASR 9006 Router, Figure 1-20 for the Cisco ASR 9904 Router,
Figure 1-26 for the Cisco ASR 9922 Router, and Figure 1-27 for the Cisco ASR 9912 Router.
In a front-mounted position, the chassis rack-mounting flanges are secured directly to the rack posts.
Note
The Cisco ASR 9922 Router and Cisco ASR 9912 Router are designed to mount in only 4-post racks.
Verifying Rack Dimensions

Before you install the chassis, measure the space between the vertical mounting flanges (rails) on your
equipment rack to verify that the rack conforms to the measurements shown in Figure 2-37.
Step 1
Mark and measure the distance between two holes on the left and right mounting rails.
The distance should measure 18.31 inches 0.06 inches (46.5 cm 0.15 cm).
Note
Step 2
Measure for pairs of holes near the bottom, middle and top of the equipment rack to ensure that
the rack posts are parallel.
Measure the space between the inner edges of the left front and right front mounting flanges on the
equipment rack.
The space must be at least 17.7 inches (45 cm) to accommodate the chassis, which is approximately
17.50 inches (44.45 cm) wide and fits between the mounting posts on the rack.
Figure 2-37
Verifying Equipment Rack Dimensions
Mounting flanges
Hole centerline
to hole centerline
18.31 inches 0.06 inches
(46.5 cm 0.15 cm)
247170
Minimum usable
aperture 17.7 inches
(45.0 cm)
2-42
Chapter 2

Installing the Chassis in a 2-Post Rack

This section describes how to install the chassis in a 2-post telco-style rack. Two people can lift an empty
router chassis using the handles on the sides. To accommodate racks with different hole patterns in their
mounting flanges, the chassis rack-mounting flanges have three groups of eight oblong screw holes on
each side.
An empty chassis weighs approximately 150 pounds (68 kg). You need two people to slide the chassis
into the equipment rack safely.
Figure 2-38 shows the orientation of the Cisco ASR 9010 Router chassis to the rack posts (3 or 6
channel width) of an industry-standard 2-post rack and components used in the installation.
Figure 2-38
Installing the Cisco ASR 9010 Router Chassis in a Standard 2-Post Rack
3
4
243187
Caution
Five screws per side (minimum) to attach the router chassis to the rack
2-43
Chapter 2
To install the Cisco ASR 9010 Router chassis in a Seismic 2-post rack for optional earthquake
protection, two side brackets must be mounted to the chassis for attachment to the posts
(5 channel width) of the GR-63 Zone 4 Seismic 2-post rack.
Note
Figure 2-39 shows the orientation of the Cisco ASR 9010 Router chassis to the Seismic 2-post rack and
components used in the installation.
Figure 2-39
Installing the Cisco ASR 9010 Router Chassis in a Seismic 2-Post Rack
3
4
243187
Five screws per

side (minimum) to
attach the router
chassis to the rack
2 Four screws
(minimum) to attach
the rear mounting
bracket to the rack
2-44
Rear mounting
bracket
4 Five screws to
attach the rear
mounting bracket to
the router chassis

Figure 2-40 shows the orientation of the Cisco ASR 9006 Router chassis to the rack posts and
Figure 2-40
1
243466
Chapter 2
Four screws per side (minimum) to attach the router chassis to the rack.
2-45
Chapter 2
Figure 2-41 shows the orientation of the Cisco ASR 9904 Router chassis to the rack posts and
Figure 2-41
351306
Six screws per side (minimum) to attach the router chassis to the rack.
2-46

Follow these steps to install the chassis in the equipment rack.

Step 1
Using two people, lift the chassis into the rack using the side handles and grasping underneath the power
supply bays (Figure 2-42).
Figure 2-42
Correct Lifting Positions
243343
Chapter 2
Caution
Do not grasp the card cage or the air inlet grill when lifting the router chassis (Figure 2-43).
2-47
Chapter 2
Incorrect Lifting Handholds
243342
Figure 2-43
Step 2
Position the chassis until the rack-mounting flanges are flush against the mounting rails on the rack.
Step 3
Hold the chassis in position against the mounting rails while the second person finger-tightens a screw
to the rack rails on each side of the chassis.
Step 4
Finger-tighten the screws to the rack rails on each side of the chassis. Space the screws evenly between
the top and bottom of the chassis.
Step 5
(Optional) For optional earthquake protection for the Cisco ASR 9010 Router or
Cisco ASR 9006 Router, two side brackets must be mounted to the chassis for attachment to the posts
(5 channel width) of a GR-63 Zone 4 Seismic 2-post rack (Figure 2-39).
Step 6
a.
Attach the side brackets to the left and right side of the chassis by finger-tightening five screws
through each bracket into the chassis.
b.
Attach the side bracket front flanges to the rack posts by finger-tightening four screws through each
bracket flange into the mounting rails of the rack.
c.
Fully tighten the five screws on each side bracket to secure the brackets to the chassis.
d.
Fully tighten the four screws on each side bracket flange to secure the brackets to the rack rails.
Fully tighten all five screws on the chassis mounting flanges on each side to secure the chassis to the
rack rails.
2-48
Chapter 2

Installing the Chassis in a 4-post Open Rack

To mount the Cisco ASR 9010 Router, Cisco ASR 9922 Router or Cisco ASR 9912 Router chassis in a
4-post open rack, two side brackets must be attached to the chassis and the rear posts. See Figure 2-44
for the Cisco ASR 9010 Router and Figure 2-47 for the Cisco ASR 9922 Router and
To mount the Cisco ASR 9006 Router (Figure 2-45) or Cisco ASR 9904 Router (Figure 2-46) in a
4-post open rack, extra brackets are not required.
Preparing the 19 Inch 45-RU Rack

To prepare the 19 Inch 45-RU rack that will contain either the Cisco ASR 9922 Router chassis or
Cisco ASR 9912 Router chassis:
Step 1
Install the two guide rails into the bottom of the rack (Figure 2-47).
The two guide rails at the bottom of the rack are included in the ASR-9922-ACC-KIT and
ASR-9912-ACC-KIT accessory kits. Use screws to fasten these two guide rails into the front and rear
rails of the rack.
The two guide rails have six holes (three per rail) that accommodate 12-24 or M6 screws. If you want to
use smaller 10-32 screws, you must use them with bushings to fit the larger holes (Figure 2-13). The
bottom rail is keyed to the EIA mounting hole pattern. Install the rails at the first RU location. The rear
rack mount brackets are installed by aligning the bracket mounting holes to the holes on the rear cover
of the chassis.
Step 2
Use a scissors jack to remove the chassis from the shipping rack. Place a pallet jack next to the chassis
inside the shipping rack and push/pull the chassis onto the pallet jack for transport to the rack.
Step 3
On the rear of the Cisco ASR 9922 Router is an integrated handle that is used to pull the chassis from
the pallet jack into the rack where the chassis is to be installed.
Step 4
a.
Position the chassis so that the rear handle is facing the front of the rack.
b.
From the rear of the rack, pull the chassis by the handle into the rack, making sure that the chassis
sits on top of the guide rails in the rack.
On the Cisco ASR 9912 Router, the handles are on the sides of the chassis. Once the chassis is pulled
into the rack and sits on top of the guide rails, use screws to fasten the chassis to the rack.
2-49
Chapter 2
Figure 2-44
Installing the Cisco ASR 9010 Router Chassis in a 4-Post Rack
1
3
243256
Rear mounting bracket
2 Five screws (minimum) to attach

the rear mounting bracket to the
rear post of the rack
2-50
Five screws (minimum) to

attach the rear mounting
bracket to the router chassis

Figure 2-45
243431
Chapter 2
2-51
Chapter 2
351305
Figure 2-46
2-52

Figure 2-47
Rack Mount Installation Kit for the Cisco ASR 9922 Router and Cisco ASR 9912 Router
344377
Chapter 2
2-53
Chapter 2
302352
Figure 2-48
2-54

Figure 2-49
303660
Chapter 2
2-55
Chapter 2

Before you connect power to the router, or power on the router for the first time, we recommend that you
connect the central office ground system or Network Equipment Building System (NEBS) to the
threaded supplemental bonding and grounding receptacles on the router. For more information on
supplemental bonding and grounding cable requirements, see NEBS Supplemental Unit Bonding and
Grounding Guidelines, page 1-52.
Table 2-3 references the grounding receptacle locations for the Cisco ASR 9000 Series Routers.
Table 2-3
Grounding Receptacle Locations
Model Number
Grounding Receptacle Location
Bottom rear right side of the chassis (Figure 2-50).
Top rear right side of the chassis (Figure 2-51).
Bottom rear right side and rear left side of the chassis (Figure 2-52).
Top rear right side of the chassis (Figure 2-53).
Bottom rear right side of the chassis (Figure 2-54).
Follow these steps to attach a grounding cable lug to the router:

Step 1
Insert the grounding screws (10-32 round-head) through the locking washers (ideally nickel-plated
brass) and into the threaded grounding receptacle (has two M6 bolt holes with 0.625 to 0.75 spacing
between them). The wire receptacle is large enough to accept a #6 AWG or larger multi-strand copper
wire.
Step 2
Tighten the grounding screws securely to the receptacles.
Step 3
Prepare the other end of the grounding wire and connect it to the appropriate grounding point at your
site to ensure an adequate earth ground.
2-56

Figure 2-50
NEBS Bonding and Grounding for the Cisco ASR 9010 Router
Figure 2-51
243440
243204
Chapter 2
2-57
Chapter 2
351298
Figure 2-52
2-58

Figure 2-53
344039
Chapter 2
2-59
Chapter 2
303673
Figure 2-54
2-60
Chapter 2

Installing Chassis Accessories

The Cisco ASR 9000 Series Routers ship with a base set of chassis accessories. To install the base
accessories and optional accessories, see the appropriate installation procedure below for your router:
Base Accessories
Note
Installing Base Chassis Accessories on the Cisco ASR 9010 Router, page 2-61.
Installing Base Chassis Accessories on the Cisco ASR 9006 Router, page 2-69
Installing Base Chassis Accessories on the Cisco ASR 9912 Router, page 2-93.
The Cisco ASR 9904 Router does not include base chassis accessories.
Optional Accessories
Installing Optional Chassis Accessories on the Cisco ASR 9010 Router, page 2-64.
Installing Optional Chassis Accessories on the Cisco ASR 9006 Router, page 2-72
Installing Optional Air Baffles on the Cisco ASR 9006 Router, page 2-75
Installing Optional Air Baffles on the Cisco ASR 9904 Router, page 2-82.
Installing Optional Chassis Accessories on the Cisco ASR 9922 Router, page 2-91.
Installing Optional Chassis Accessories on the Cisco ASR 9912 Router, page 2-95
Installing Base Chassis Accessories on the Cisco ASR 9010 Router

The base chassis accessories for the Cisco ASR 9010 Router include:
Note
Two ball studs
Two plastic side strips
One accessory front grill
If you ordered the optional accessories set, see Installing Optional Chassis Accessories on the
Cisco ASR 9010 Router, page 2-64 to install both the base and optional accessories.
If you did not order the optional accessory set, follow these steps to install the supplied base chassis
accessories on the Cisco ASR 9010 Router:
Step 1
Install two ball studs (one per side) into the chassis front edge (Figure 2-55) near the top of the chassis
grill. Tighten the ball studs to a torque of 8 in-lb (0.90 N-m).
2-61
Chapter 2
Installing Ball Studs: Version 1 Power Cisco ASR 9010 Router (Base Accessories
Installation)
243457
Figure 2-55
Step 2
Attach two plastic strips (one per side) along the chassis front edge. The bottom tab of each strip attaches
to the hole about 2 inches above the ball stud locations (Figure 2-56).
Step 3
Attach the accessory grill to the chassis in front of the chassis grill. The top of the accessory grill attaches
to the ball studs.
Note
You must install the lower fan tray before attaching the accessory grill. The lower fan tray slot is located
behind the accessory grill. See Installing Fan Trays, page 3-4.
2-62

Figure 2-56
243457
Chapter 2
Two are ball studs inserted

in front chassis edge
threaded holes next to
chassis grill
Two side strips attach to front

chassis edge (one per side).
3 Accessory grill attaches

to front chassis edge by
attaching to ball studs.
2-63
Chapter 2
Installing Optional Chassis Accessories on the Cisco ASR 9010 Router

The optional chassis accessories for the Cisco ASR 9010 Router include:
Note
Six ball studs
Two L-shaped brackets
Two hinge brackets (left and right side)
Eight screws (plus one extra) for attaching the hinge brackets
Four screws for attaching the L-shaped brackets
Two doors (left and right side)
One mid-cover with door lock
Installation of the optional accessory pieces also includes the base accessory ball studs and front grill.
The base accessory side strips are not used when installing the optional chassis accessories.
If you ordered the optional accessories set, follow these steps to install both the base and optional
accessories (Figure 2-57):
Step 1
Attach the left L-shaped bracket (item 3 in Figure 2-57) to the left hinge bracket (item 2 in Figure 2-57)
with two screws. Tighten the screws to a torque of 5 in-lb (0.55 N-m).
Step 2
Repeat Step 1 for the right hinge bracket and right L-shaped bracket.
Step 3
Remove the two screws that secure the bottom edge of the cable management tray to the chassis.
Step 4
Install six ball studs (three per side) into the chassis front edge (item 7 in Figure 2-57 and Figure 2-58).
Tighten the ball studs to a torque of 8 in-lb (0.90 N-m).
2-64

Figure 2-57
Optional Chassis Accessories for the Cisco ASR 9010 Router
2
3
5
4
6
8
7
248659
Chapter 2
Door (one per side)
Screws for attaching the L-shaped bracket to

the hinge bracket (one screw is removed and
re-inserted to attach the L-shaped bracket to
the cable management tray and chassis)
Hinge bracket (one per side)
Mid-cover with door lock
L-shaped bracket (one per side)
Balls studs (three per side)
Four screws for attaching each hinge bracket

(eight screws total)
Front grill
2-65
Chapter 2
Locations for the Six Ball Studs on the Cisco ASR 9010 Router
303445
Figure 2-58
Step 5
Attach the left and right hinge brackets to the chassis using four screws for each bracket. Tighten the
screws to a torque of 11 in-lb (1.20 N-m). The L-shaped brackets should align with the holes in the cable
management tray from which you removed the screws.
Step 6
Secure the L-shaped brackets to the chassis and cable management tray by re-inserting and tightening
the cable management tray screws you removed (Figure 2-59).
2-66

Figure 2-59
Installing the Hinge Brackets and L-Shaped Brackets on the Cisco ASR 9010 Router
249244
Chapter 2
Install each hinge bracket, with an L-shaped

bracket attached, using four screws.
After the hinge brackets are installed, secure

each L-shaped bracket to the cable
management tray and chassis with the screw
that you previously removed from that
location.
Step 7
Install the mid-cover with door lock (item 6 in Figure 2-57) by engaging it to the upper four ball studs
and lining up the grooves in the top outside edges of the mid-cover with ridges at the bottom of the hinge
brackets.
Step 8
Attach two doors to the hinge brackets (one per side). For each door:
a.
Align the door hinge hole with the bracket hinge hole (Figure 2-60).
b.
Insert the captive pin in the door hinge through the hole in the bracket hinge.
2-67
Chapter 2
Note
You must install the lower fan tray before attaching the accessory grill. The lower fan tray slot is located
behind the accessory grill. See Installing Fan Trays, page 3-4.
Installing Optional Chassis Accessory Doors on the Cisco ASR 9010 Router
248660
Figure 2-60
Step 9
Install the front grill (item 8 in Figure 2-57) by aligning and engaging it to the bottom two ball studs and
pressing it in.
2-68
Chapter 2


The base chassis accessories for the Cisco ASR 9006 Router include:
Note
One plastic fan tray door accessory piece
Two metal mounting brackets (left and right)
Two chassis side brackets (left and right)
Two plastic chassis corner pieces (left and right)
Two screws for attaching the plastic fan tray door accessory piece
Six screws for attaching the metal mounting brackets
Six screws for attaching the side brackets
If you ordered the optional accessories set, see Installing Optional Chassis Accessories on the
Cisco ASR 9006 Router, page 2-72 to install both the base and optional accessories.
If you did not order the optional accessory set, follow these steps to install the supplied base chassis
accessories on the Cisco ASR 9006 Router.
Step 1
Attach the plastic accessory piece to the fan tray door using two supplied screws. Insert the screws
through the fan tray door from the inside of the door into the accessory piece (Figure 2-61).
Step 2
Attach the left metal mounting bracket to the front upper left corner of the chassis with three screws.
2-69
Chapter 2
Figure 2-61
Installing Plastic Fan Tray Door Accessory and Metal Mounting Brackets on the Cisco ASR 9006 Router
243540
Plastic fan tray door

accessory
Metal mounting bracket on

left upper corner of chassis
Step 3
Attach the right metal mounting bracket to the front upper right corner of the chassis with three screws.
Step 4
Attach the left and right side brackets to the chassis front edge on each side (Figure 2-62). Attach each
bracket to the chassis using three screws per bracket inserted from the inside of the chassis, through the
three chassis tabs into the plastic brackets. Tighten the screws to a torque of 7 in-lb (0.80 N-m).
2-70
3 Metal mounting bracket on

right upper corner of chassis

Figure 2-62
Installing Chassis Side Brackets on the Cisco ASR 9010 Router
1
243542
Chapter 2
Left chassis side bracket
Six screws for attaching the

chassis side brackets (three
per side)
3 Right chassis side bracket
Step 5
Attach the left plastic corner piece to the mounting bracket at the front upper left corner of the chassis
(Figure 2-63).
Step 6
Attach the right plastic corner piece to the mounting bracket at the front upper right corner of the chassis.
2-71
Chapter 2
Installing Plastic Chassis Corners on the Cisco ASR 9006 Router (Base Accessories
Installation)
243541
Figure 2-63
Plastic chassis corner piece attaches to

metal bracket at upper left corner of
chassis

metal bracket at upper right corner of
chassis
After the chassis has been installed in the rack and all chassis accessories have been attached, you can
install the fan trays, power supply modules, and RSP and line cards. See Chapter 3, Installing Cards
and Modules in the Chassis, for detailed installation instructions.

Four ball stud assembly pieces (one set of two pieces per side)
One door with attached hinges
Four screws for assembling and attaching the ball stud assemblies
Four small hex nuts for attaching the door hinges
2-72

Installation of the optional accessory pieces also includes all base accessory pieces. If you ordered the
optional accessories set, follow these steps to install both the base and optional accessories:
Step 1
Perform Step 1 through Step 4 of the Installing Base Chassis Accessories on the Cisco ASR 9006 Router,
page 2-69.
Step 2
Assemble and attach the two ball stud assemblies (Figure 2-64) to each chassis side bracket. For each
assembly:
a.
Align the two halves of the assembly to each other and to the screw holes in the chassis side bracket.
b.
Insert and tighten two screws to secure the assembly to the side bracket.
Figure 2-64
Installing Ball Stud Assemblies on the Cisco ASR 9006 Router (Shown with Version 1
Power System)
5
4
6
8
7
248659
Chapter 2
Step 3
Caution
Attach the door to the upper chassis panel (Figure 2-65) using two hex nuts per side to secure the door
hinges to the panel. Tighten the hex nuts to a torque of 4 in-lb (0.45 N-m).
Do not overtighten the hex nuts. They can be broken through overtightening.
2-73
Chapter 2
Caution
When opening the door, be sure to grasp the center of the door to pull it open. Do not open the door by
pulling on a corner or side of the door frame.
Installing the Optional Accessory Door on the Cisco ASR 9006 Router
248670
Figure 2-65
Step 4
Attach the left plastic corner piece to the mounting bracket at the front upper left corner of the chassis
(Figure 2-66).
Step 5
Attach the right plastic corner piece to the mounting bracket at the front upper right corner of the chassis.
2-74
Chapter 2

Figure 2-66
Installing Plastic Chassis Corners on the Cisco ASR 9006 Router (Optional
Accessories Installation)
249226
1
2

metal bracket at upper left corner of
chassis

metal bracket at upper right corner of
chassis
install the fan trays, power supply modules, and RSP and line cards. See Chapter 3, Installing Cards
and Modules in the Chassis for detailed installation instructions.
Installing Optional Air Baffles on the Cisco ASR 9006 Router

The Cisco ASR 9006 Router has an optional air baffle accessory kit (800-43858-01) for mounting the
router chassis in a 2-post or 4-post 19-inch rack. The accessory kit includes:
One plenum with two pre-installed front rack-mounting brackets for attaching plenum to front
side of rack-post
One support bracket
One plastic glide strip
Two rear rack-mounting brackets for attaching plenum to rear side of rack-post
Twelve 12-24 x 0.5 in. pan-head screws (six for attaching support bracket to chassis and six for
securing chassis to rack-mounted plenum)

Twelve 8-32 x 0.5 in. pan-head screws for attaching rear rack-mounting brackets on plenum
Air baffles allow for front-to-back air flow through the chassis and help isolate exhaust air from the
intake air.
2-75
Chapter 2
If you ordered the optional air baffle accessory kit, follow these steps to install it:
Step 1
Attach the support bracket (part number: 800-43857-01) to the left side of the Cisco ASR 9006 Router
using six 12-24 x 0.5 in. pan-head screws (part number: 48-0523-01). See Figure 2-67.
Figure 2-67
Attaching the Support Bracket to the Left Side of the Cisco ASR 9006 Router Chassis
2-76

Step 2
Remove the paper liner from the plastic guide strip and install on the right side of the chassis card cage,
as shown in Figure 2-68.
Figure 2-68
Attaching Plastic Glide Strip to Chassis
363473
Chapter 2
2-77
Chapter 2
Step 3
Figure 2-69
Install the plenum in the rack. Insert and tighten four customer-supplied screws to secure the plenum to
the front of the rack-post (two on each side). These screws can vary in size and type depending on the
rack that you use. Torque the screws to the weight specified for your particular rack. See Figure 2-69 and
Figure 2-70.
Plenum with Pre-Installed Front Mounting Brackets
1
Step 4
Step 5
Front rack-mounting bracket, pre-installed
Attach the rear rack-mounting brackets (part number: 700-47414-01) to the left and right sides of the
plenum base, using twelve 8-32 x 0.5 in. pan-head screws ((part number: 48-0828-01), six per bracket.
If you are installing the chassis in a two-post rack, the rear rack-mounting brackets secure the
plenum to the rear of the rack-posts (Figure 2-70).
If you are installing the chassis in a four-post rack, rotate the rear rack-mounting brackets by 180
degrees and attach to both sides of the plenum. The rear rack-mounting brackets secure the plenum
to the rear rack-posts.
Insert and tighten four customer-supplied screws to secure the plenum to the rear of the rack-post (two
on each side). These screws can vary in size and type depending on the rack that you use. Torque the
screws to the weight specified for your particular rack (Figure 2-70).
2-78
Chapter 2

Figure 2-70
Installing the Plenum in a Two-Post 19-Inch Rack
Screw attaching rear-rack mounting bracket to 3

plenum (six per bracket)
Rear rack-mounting bracket
Screws attaching rear-rack mounting bracket

to rack (two per bracket)
Step 6
Turn the chassis sideways and slide it into the rack (Figure 2-71).
Step 7
Insert and tighten four customer-supplied rack-mounting screws to secure the support bracket on the
chassis to the front of the rack-post (two on each side). These screws can vary in size and type depending
on the rack that you use. Torque the screws to the weight specified for your particular rack (Figure 2-71).
2-79
Chapter 2
Step 8
Insert six 12-24 x 0.5 in.pan-head screws (part number: 48-0523-01) screws to secure the chassis to the
rack-mounted plenum (Figure 2-71).
Figure 2-71
1
Step 9
Securing the ASR 9006 Router in a Two-Post 19-Inch Rack
Screws attaching chassis to rack
Screws attaching chassis to plenum
Install the optional chassis accessories, if desired. See Installing Optional Chassis Accessories on the
Cisco ASR 9006 Router, page 2-72.
Figure 2-72 shows the air baffle accessory kit and Cisco ASR 9006 Router with its optional accessories
fully installed in a two-post 19-inch rack.
2-80
Chapter 2

Figure 2-72
Cisco ASR 9006 Router Fully Installed with Air Baffle Accessory Kit and Optional
Chassis Accessories
2-81
Chapter 2
Installing Optional Air Baffles on the Cisco ASR 9904 Router

The Cisco ASR 9904 Router has an optional air baffle accessory kit (ASR-9904-BAFFLE=) for
mounting the router chassis in a 2-post 23-inch rack. The accessory kit includes:
Two adapter plates
Two air baffles (left and right)
Two air deflectors
Twenty-eight 12-24 screws for attaching the air baffles and air deflectors to the adapter plate
Eight 8-32 screws for securing the side baffles to the air deflectors
Air baffles allow for front-to-back air flow through the chassis and help isolate exhaust air from the
intake air. For air baffle dimensions, see Figure 2-80 and Figure 2-81.
If you ordered the air baffle accessory kit, follow these steps to install it:
Step 1
Attach the adapter plates (Figure 2-73) to the left and right rack rails using customer-supplied rack
screws (we recommend a minimum of ten per side). These screws can vary in size and type depending
on the rack that you use. Torque the screws to the weight specified for your particular rack.
Attaching the Adapter Plates to the Left and Right Rack Rails on the
Cisco ASR 9904 Router Chassis
390152
Figure 2-73
2-82

Loosely attach the left and right side air baffles to the adapter plate (Figure 2-74) with 12-24 screws
(four per side). Do not tighten these screws. To ensure the correct orientation, Left Front and Right
Front are stamped on each side of the baffle.
Step 2
Figure 2-74
Installing the Air Baffles on the Cisco ASR 9904 Router Chassis
2
1
3
390150
Chapter 2
Right side air baffle
Left side air baffle
12-24 screws for attaching the baffles (four per side)
2-83
Chapter 2
Step 3
Install the top and bottom air deflectors (Figure 2-75) with the bottom side stamp facing down (note
that the top and bottom air deflectors both have the same part number: 800-41357-01).
Step 4
Tighten the screws to a torque of 41 in-lb.

Figure 2-75
Attaching the Air Deflectors on the Cisco ASR 9904 Router Chassis Top View
390147
Top air deflector
12-24 screws for attaching the air deflectors (two screws per side)
Bottom air deflector
Bottom side stamp
2-84

Step 5
Secure the side air baffles to the air deflectors using the supplied 8-32 screws (Figure 2-76). Do not
tighten the screws.
Figure 2-76
Securing the Cisco ASR 9904 Router Chassis Side Baffles to the Air Deflectors
(Rear View)
390151
Chapter 2
2-85
Chapter 2
Step 6
Use six 12-24 screws to fasten each side of the chassis to the 23-inch rack. Torque each of the six screws
to 41 in-lbs. (Figure 2-77).
Mounting the Cisco ASR 9904 Router Chassis in a 23-Inch Rack
390148
Figure 2-77
2-86

Step 7
Tighten the remaining loose screws to complete the installation. Torque the 8-32 screws to 18 in-lb and
the 12-24 screws to 41 in-lb.
Figure 2-78 shows the router chassis with the air baffle installed in a 2-post 23-inch rack.
Figure 2-78
Cisco ASR 9904 Router Chassis with Air Baffle in 2-Post 23-Inch Rack
390149
Chapter 2
An electrical conducting path must exist between the product chassis and the metal surface of the
enclosure or rack in which it is mounted, or to a grounding conductor. The chassis has two grounding
points on each side of the baffle, however only one ground is required. The other will be grounded
through the top and bottom air deflectors. Figure 2-79 shows the baffle ground location on the chassis.
You can ground the baffle by either attaching a grounding lug to the chassis (NEBS Supplemental Unit
Bonding and Grounding Guidelines, page 1-52), or by using thread-forming mounting screws to
establish a metal-to-metal contact. If you are using screws, remove any paint or other non-conductive
coatings on the surfaces between the mounting hardware and the enclosure or rack. Clean all surfaces
and apply an antioxidant applied before the installation.
2-87
Chapter 2
Figure 2-79
Cisco ASR 9904 Router Baffle Ground
390247
Baffle ground location
2-88

Figure 2-80
Cisco ASR 9904 Router Air Baffle DimensionsTop View
24.59 in
(62.5 cm)
21.19 in
(53.8 cm)
17.57 in
(44.6 cm)
1.26 in
(3.2 cm)
25.00 in 20.16 in
(63.5 cm) (51.2 cm)
20.54 in
(52.2 cm)
9.96 in
(25.3 cm)
2X
23" ADAPTER PLATE
700-44117-01
2.57 in
(6.5 cm)
390299
Chapter 2
2.32 in
(5.9cm)
2-89
Chapter 2
Figure 2-81
Cisco ASR 9904 Router Air Baffle DimensionsFront View
23.00 in
(58.4 cm)
22.31 in
(56.7 cm)
17.46 in
(44.3 cm)
0.86 in
(2.2 cm)
2-90
390300
1.75 in
(4.4 cm)
Chapter 2


Fan tray covers
Top and bottom card cage front doors
Rear exhaust air deflector
If you ordered the optional accessories set, follow these steps to install the accessories:
Note
Remove the two screws that secure the bottom edge of the cable management tray to the chassis.
Four ball studs are preinstalled on the Cisco ASR 9922 Router chassis.
Figure 2-82
Optional Fan Tray Covers for the Cisco ASR 9922 Router
302403
Step 1
2-91
Chapter 2
Figure 2-83
Optional Card Cage Doors for the Cisco ASR 9922 Router
302407
Card cage door
Hinge bracket
Step 2
Attach the left and right hinge brackets to the chassis using three screws (M4 thread) for each bracket.
Tighten the screws to a torque of 11 in-lb (1.20 N-m). The L-shaped brackets should align with the holes
in the cable management tray from which you removed the screws.
Step 3
Secure the L-shaped brackets to the chassis and cable management tray by re-inserting and tightening
the cable management tray screws you removed.
Step 4
Align the exhaust air deflector at the rear of the chassis behind the top fan tray outlets (Figure 2-84), and
use a screwdriver to tighten the two screws, one on each side of the deflector. The deflectors
measurements are width 17.48 x height 4.72 x depth 5.21 and deflects the outgoing exhaust air.
2-92
Chapter 2

Optional Rear Exhaust Air Deflector on the Cisco ASR 9922 Router
303591
Figure 2-84
install the fan trays, power supply modules, RP cards, FCs and LCs. See Chapter 3, Installing Cards
and Modules in the Chassis, for detailed installation instructions.

The base chassis accessories for the Cisco ASR 9912 Router include (Figure 2-85):
One honeycomb cosmetic cover
One vented bezel to cover the front of the power system
Step 1
Attach the honeycomb cosmetic cover to the front of the chassis above the cable management bracket by
aligning the cover above the screw tabs on the chassis.
Step 2
Attach the vented bezel cover by snapping it into place in front of the power system.
Note
You will need to remove the vented bezel cover in order to install the power system. After the
power system is installed, you can re-install the vented bezel cover.
2-93
Chapter 2
Installing Base Accessories on the Cisco ASR 9912 Router
303692
Figure 2-85
install the fan trays, RP cards, FCs and LCs. See Chapter 3, Installing Cards and Modules in the
Chassis, for detailed installation instructions.
2-94
Chapter 2


Front door for the line card cage
Two hinge brackets (left and right side)
Six screws for attaching the hinge brackets to the chassis
Rear exhaust air deflector
If you ordered the optional accessories set, follow these steps to install the accessories:
Step 1
Attach the left (if not pre-installed) and right hinge brackets to the chassis using three screws (M4 thread)
for each bracket (Figure 2-86). Tighten the screws to a torque of 11 in-lb (1.20 N-m).
Figure 2-86
Optional Card Cage Door on the Front of the Cisco ASR 9912 Router
303693
Card cage door
Hinge bracket
2-95
Chapter 2
Step 2
Align the exhaust air deflector at the top rear of the chassis above the fan trays (Figure 2-87), and use a
screwdriver to tighten the two screws, one on each side of the deflector.
Optional Rear Exhaust Air Deflector on the Cisco ASR 9912 Router
303671
Figure 2-87
install the fan trays, RP cards, FCs, and LCs. See Chapter 3, Installing Cards and Modules in the
Chassis, for detailed installation instructions.
2-96
CH A P T E R

This chapter contains the procedures for installing cards and modules into the chassis after the chassis
has been installed into a rack. This chapter also describes how to connect cables to RSP, RP, alarm, and
line cards.
Note
The procedures in this chapter for all Cisco ASR 9000 Series Routers are identical unless otherwise
noted.
Installing Power Modules, page 3-1
Installing Fan Trays, page 3-4
Installing Cards in the Chassis, page 3-6
Connecting Line Card Network Interface Cables, page 3-17
Connecting Cables to the RSP or RP, page 3-22
Connecting the Alarm Cable, page 3-25
Connecting Power to the Router, page 3-26
Powering On the Router, page 3-32
Installing Power Modules

The following procedures describe how to reinstall the power modules back into the chassis. Be sure to
follow the correct procedure for the type of power modules that you have.
Caution
Never force a power module into the power tray if you feel any resistance! The power modules are keyed
to prevent AC modules from being plugged into a DC power tray or a DC module into an AC power tray.
Forcing a module into the incorrect tray can cause damage to the module and the tray.
3-1
Chapter 3
Installing AC Power Modules

Prerequisites
There are no prerequisites for this task.

You need the following tool to perform this task:
7/16 hex socket and torque wrench, torque 50 in-lb.
Steps
Follow these steps to reinstall the AC power modules back into the chassis (see Figure 3-1 for the
version 1 power module, Figure 3-2 for the version 2 and version 3 power modules, and Figure 3-3 for
installing a version 2 power module in the Cisco ASR 9904 Router.
Note
Step 1
Caution
The Slide the power module into the power tray until it mates with its backplane connector.
Secure the module:
a.
Version 1 power module: Pivot the power module door fully to the left until it locks to securely seat
the power module to its backplane connector.
b.
Version 2 and version 3 power modules: Move the handle up and tighten the screw using the 7/16
hex socket and torque wrench with the torque set to 50 in-lb.
To prevent damage to the power tray backplane connector, do not use excessive force when inserting the
power module into the power tray.
Step 2
Repeat Note and Step 1 for the other AC power modules.
Step 3
Go to Installing Fan Trays, page 3-4 to install the fan tray.

Installing a Version 1 Power- Module
243181
Figure 3-1
3-2

Installing a Version 2 or Version 3 Power Module in the Cisco ASR 9010, 9912, 9922
Routers
Figure 3-3
Installing a Version 2 Power Module in the Cisco ASR 9904 Router
331400
Figure 3-2
351307
Chapter 3
3-3
Chapter 3
Installing Fan Trays
Installing DC Power Modules

7/16 hex socket and torque wrench, torque 50 in-lb.
Steps
Follow these steps to reinstall the DC power modules back into the chassis (see Figure 3-1 for the
version 1 power module or Figure 3-2 for the version 2 or version 3 power module.
Step 1
Slide the power module into the power tray until it mates with its backplane connector.
Step 2
Secure the module.
Caution
Step 3
a.
Version 1 power module: Pivot the power module door fully to the left until it locks to securely seat
the power module to its backplane connector.
b.
Version 2 power and version 3 module: Move the handle up and tighten the screw using the 7/16 hex
socket and torque wrench with the torque set to 50 in-lb.
Repeat Step 1 and Step 1 for the other DC power modules.

Prerequisites
Install the power modules before installing the fan trays.

6-inch long number 2 Phillips screwdriver, torque 10 inch-lb.
Steps
Note
If you are installing a fan tray for the Cisco ASR 9010 Router, install the lower fan tray before attaching
the accessory grill. The lower fan tray slot is located behind the accessory grill. See the Installing Chassis
Accessories, page 2-61
3-4
Chapter 3

Before installing the fan tray, first determine its location. Refer to the figure that applies to your router.
See Removing Fan Trays, page 2-18.
Follow these steps to install fan trays in the chassis.
Step 1
Lift the fan tray (with two hands) and slide it halfway into the module bay.
Step 2
Slowly push the fan tray into the chassis until it mates with the backplane connector at the back of the
chassis bay.
Caution
To prevent damage to the connectors, do not use excessive force when inserting the fan tray into the
chassis.
Step 3
Tighten the captive screw(s) on the fan tray using the 6-inch long number 2 Phillips screwdriver to a
torque of 10 in-lb to secure it to the chassis.
Step 4
Repeat Step 1 through Step 3 for the second fan tray.
Note
On the Cisco ASR 9922 Router, the third and fourth fan trays (under the middle cage) are
installed upside down compared to the first and second fan trays (above the middle cage).
3-5
Chapter 3
Installing Cards in the Chassis

This section describes how to reinstall the RSP cards, RP cards, FCs, and LCs back into the chassis.
See the Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation
Guide for information about installing shared port adapter (SPA) and SPA interface processor (SIP)
cards.
Caution
Be sure to verify that you are inserting a card into its correct slot. RSP/RP cards must only be inserted
in the two slots reserved for RSP/RP cards (RSP0, RSP1, RP0, RP1). FCs must only be inserted in the
FC slots of the Cisco ASR 9922 Router and Cisco ASR 9912 Router. All other slots are for LCs.
Caution
Unoccupied card slots must have a blank filler card installed for electromagnetic compatibility (EMC)
and to ensure proper air flow through the chassis.
Caution
Be careful to avoid damaging the electromagnetic interference (EMI) gasket that runs along the full
height of the card front panel edges. Damage to the EMI gasket can affect the ability of your system to
meet EMC requirements.
Caution
Caution
To avoid damaging card mechanical components, never carry an RSP card, RP card, FC, or LC by the
captive installation screws or ejector levers. Doing so can damage these components and cause card
insertion problems.
Caution
Be sure to always tighten the captive installation screws on the RSP card, RP card, FC, or LC. Failure to
tighten the screws can cause boot failure or prevent proper router operation.
3-6
Chapter 3

Installing RSP Cards in the Chassis

Follow these steps to reinstall RSP cards into the chassis (See Figure 2-20 and Figure 2-21 for slot
numbering):
Step 1
Starting at slot RSP0, slide the card into the slot.
Step 2
Pivot the ejector levers to seat the card to the backplane connector.
Caution
Do not apply excessive force to the RSP card to seat it. When seated, the RSP card ejector levers are
angled slightly outward from the card faceplate (item 1 in Figure 3-4). When the captive installation
screws are fully tightened, the ejector levers are parallel to the card faceplate (item 2 in Figure 3-4).
Some flexing in the backplane is normal. When you push the ejector levers fully vertical, the card is
seated in the backplane connectors. However, when you release the levers, backplane flexing pushes the
levers out, so the levers may be slightly loose. Tightening the captive installation screws prevents any
additional movement from flexing of the backplane.
Step 3
Tighten the captive screws at the top and bottom of the front panel to a torque of 10 +/1 in-lb.
Step 4
Repeat Step 1 through Step 3 to install the second RSP card into slot RSP1.
Note
Even when the RSP card is fully seated with installation screws fully tightened, there may be a slight
gap between the card and the chassis (item 3 in Figure 3-4).
3-7
Chapter 3
RSP Card Ejector Lever Positions During Installation
243400
Figure 3-4
Note: Vertical red lines in Figure 3-4 indicate a line fully parallel to the RSP card front panel.
1
Slightly loose position of

ejector levers when the RSP
card is fully seated in the
backplane, but the captive
installation screws are not
fully tightened
Fully parallel position of

ejector levers when the RSP
card is fully seated in the
backplane and captive
installation screws are fully
tightened
3-8
Slight gap that may be

present when the RSP card is
fully seated in the backplane
and captive installation
screws are fully tightened
Chapter 3

RSP Cable Management Ties

The Cisco ASR 9010 Router has cable management ties on the front of the cable management tray
assembly. Cables to the RSP cards can be routed as shown in Figure 3-5 to separate them from line card
cabling.
Figure 3-5
RSP Cable Management Ties
194803
Hinged cover (shown in the

raised position)
RSP cable bundle routed

through the tray
RSP cable management tie
3-9
Chapter 3
Installing RP Cards in the Chassis

Follow these steps to reinstall RP cards into the Cisco ASR 9922 Router (see Figure 2-27 for slot
numbering) and Cisco ASR 9912 Router (see Figure 2-31 for slot numbering).
Step 1
Starting at slot RP0, slide the card into the slot.
Step 2
Caution
Do not apply excessive force to the RP card to seat it. When seated, the RP card ejector levers are angled
slightly outward from the card faceplate (item 1 in Figure 3-4). When the captive installation screws are
fully tightened, the ejector levers are parallel to the card faceplate (item 2 in Figure 3-4). Some flexing
in the backplane is normal. When you push the ejector levers fully vertical, the card is seated in the
backplane connectors. However, when you release the levers, backplane flexing pushes the levers out,
so the levers may be slightly loose. Tightening the captive installation screws prevents any additional
movement from flexing of the backplane.
Step 3
Step 4
Repeat Step 1 through Step 3 to install the second RP card into slot RP1.
Note
Even when the RP card is fully seated with installation screws fully tightened, there may be a slight gap
between the card and the chassis (item 3 in Figure 3-4).
3-10
Chapter 3

Installing Fabric Cards in the Chassis

Follow these steps to reinstall fabric cards (FCs) into the Cisco ASR 9922 Router (see Figure 2-27 for
slot numbering) and Cisco ASR 9912 Router (see Figure 2-31 for slot numbering).
Step 1
Starting at slot FC0, slide the card into the slot.
Step 2
Caution
Do not apply excessive force to the FC to seat it. When seated, the FC ejector levers are angled slightly
outward from the card faceplate (item 1 in Figure 3-4). When the captive installation screws are fully
tightened, the ejector levers are parallel to the card faceplate (item 2 in Figure 3-4). Some flexing in the
backplane is normal. When you push the ejector levers fully vertical, the card is seated in the backplane
connectors. However, when you release the levers, backplane flexing pushes the levers out, so the levers
may be slightly loose. Tightening the captive installation screws prevents any additional movement from
flexing of the backplane.
Step 3
Step 4
Repeat Step 1 through Step 3 to install the remaining FCs into slots FC1 to FC6.
Note
Even when the FC is fully seated with installation screws fully tightened, there may be a slight gap
between the card and the chassis (item 3 in Figure 3-4).
Installing Line Cards in the Chassis

Before you begin reinstalling cards in the card cage, identify slot assignments by referring to the written
list you prepared when you removed the cards (see Figure 2-20, Figure 2-22, and Figure 2-27, and
Figure 2-31 for slot numbering).
Caution
Be careful to avoid damaging the EMI gasket that runs along the full height of the card front panel edges.
Damage to the EMI gasket can affect the ability of your system to meet EMI requirements.
Follow these steps to reinstall line cards in the chassis card cage:
Step 1
Starting at the lowest numbered line card slot, slide the card into the slot (see Figure 3-6, Figure 3-7,
Figure 3-9, or Figure 3-10) until it mates with the backplane connector.
Step 2
Pivot the ejector levers to seat the card into the backplane connector.
Step 3
3-11
Chapter 3
Figure 3-6
Installing a Line Card into the Cisco ASR 9010 Router Chassis
MGT LAN 0
MGT LAN 0
MGT LAN 1
ACT
ACT
MGT LAN 1
LINK
LINK
CONSOLE
CONSOLE
BITS
BITS
0
J.211
J.211
BITS
BITS
1
J.211
J.211
ALARM OUT
ALARM OUT
ACO
ACO
LAMP
TEST
LAMP
TEST
FAIL
SYNC
CRIT
HDD
MAJ
CF
FAIL
CRIT
MIN
ARE PROPE
RLY INSTAL
LED WHEN
SCREWS ARE
TIGHTENED
HDD
CF
MIN
ACO
ACO
TO10 IN/LB
243194
IMPORTANT
- CARDS
SYNC
MAJ
Slide the card into the

chassis.

seat the card into the
3-12
Tighten the captive screws.

Figure 3-7
3
2
248314
Chapter 3

chassis.

3-13
Chapter 3
Installing a Line Card in the Cisco ASR 9904 Router Chassis
351303
Figure 3-8
3
1

chassis.

3-14

Figure 3-9
344086
Chapter 3

chassis.

3-15
Chapter 3
Figure 3-10
3
2
Step 4

chassis.

In the Cisco ASR 9922 Router, up to ten line cards are installed in slots 0 through 9 in the top
card cage, and up to ten line cards are installed upside down in slots 10 through 19 in the bottom
card cage.
Go to the Connecting Line Card Network Interface Cables, page 3-17 to connect the network interface
cables.
3-16
Repeat Step 1 through Step 3 for each line card.
Note
Step 5
303694
Chapter 3


This section describes how to route the network interface cables through the router cable-management
system and attach the network interface cables to the line card ports.
This procedure uses an 40x1GE line card as an example to describe how to attach a network interface
cable to a line card port and route the cable through the cable-management system. Depending on which
line cards are installed in your system, your cable connection procedure might differ slightly from this
example. For cable connection information for your specific line card, refer to the installation and
configuration note for that line card.
Note
You can access the most current Cisco line card documentation online at: http://www.cisco.com
Follow these steps as an example to route the network interface cables through the cable-management
system and connect them to the line card:
Step 1
Note
Route an interface cable across the horizontal cable management tray (Figure 3-11), and down through
the cable tray opening to connect it to the line card.
Each line card has its own cable routing slot in the cable management tray. For example, Figure 3-11
shows cables being routed to line card 3 in slot 3 in a Cisco ASR 9010 Router.
Figure 3-11
Routing Interface Cables through the Cable Management Tray
243259
1
Step 2
Hinged cover (shown in the raised position)
2 Line card cable bundle routed through the tray
Attach a line card cable management bracket to the line card front panel (Figure 3-12). This bracket is
shipped with the line card.
3-17
Chapter 3
Step 3
Route the cable through the cable-management bracket and carefully press the cable into the channel so
it is held in place by the cable clips, as shown in Figure 3-13.
For an example of cable routing in the Cisco ASR 9006 Router, see Figure 3-14.
For an example of cable routing in the Cisco ASR 9904 Router, see Figure 3-15.
Step 4
Insert the cable connector into its assigned port.
Step 5
Repeat Step 1 through Step 4 for each additional cable connection to that line card.
Attaching a Line Card Cable Management Bracket
243255
Figure 3-12
Caution
Make sure the interface cables do not have any kinks or sharp bends, which can destroy or degrade the
ability of the optical fiber to propagate the signal-encoded beam of light accurately from one end of the
cable to the other. Always allow adequate strain relief in the interface cable.
3-18

Figure 3-13
Interface Cable Routing Using the Line Card Cable Management Bracket
243252
Chapter 3
3-19
Chapter 3
Figure 3-14
Interface Cable Routing Using the Line Card and Chassis Cable Management Bracket
on the Cisco ASR 9006 Router
1
3
5
7
9
11
13
15
17
19
6
8
7
21
10
23
12
25
14
11
27
16
13
29
18
15
31
17
19
33
20
35
22
28
25
14
27
16
29
18
30
13
10
23
12
ALAR
BITS
35
37
39
28
J.211
30
SYNC
0
32
34
SYNC
1
36
J.211
SYNC
38
T
SYNC
243406
FAIL
HDD
BITS
M OU
FAIL
J.211
CF
ALAR
BITS
ACO
ACT
33
26
MAJ
J.211
24
MIN
CONS
OLE
AUX
LINK
31
CF
BITS
22
ACO
20
M OU
MAJ
LAN
29
18
SYNC
1
ACO
MGT
27
16
SYNC
0
ACT
25
14
MIN
CONS
OLE
LAMP
TEST
ACT
21
AUX
LINK
38
ACO
36
19
LAMP
TEST
LINK
ACT
LAN
34
17
MGT
32
15
LINK
39
28
11
0
38
37
26
LAN
36
35
24
MGT
34
33
22
32
20
LAN
30
31
MGT
39
26
23
12
37
24
21
10
CRIT
HDD
CRIT
3-20

Figure 3-15
Interface Cable Routing Using the Line Card and Chassis Cable Management Bracket
on the Cisco ASR 9904 Router
351308
Chapter 3
3-21
Chapter 3
Connecting Cables to the RSP or RP

This section describes how to connect cables to the console, auxiliary, and Ethernet ports on the RSP/RP.
The console and auxiliary ports are both asynchronous serial ports; any devices connected to these ports
must be capable of asynchronous transmission. For example, most modems are asynchronous devices.
Figure 3-16 shows an example of an RSP with data terminal and modem connections called out.
Figure 3-16
RSP Console and Auxiliary Port Connections
3
4
5
243082
Console terminal
RJ-45 Ethernet cables
Modem
Console port
Auxiliary (AUX) port
Figure 3-17 shows an example of an RP with data terminal and modem connections called out.
3-22

Figure 3-17
RP Console and Auxiliary Port Connections
3
4
5
302419
Chapter 3
Console terminal
RJ-45 Ethernet cables
Modem
Console port
Auxiliary (AUX) port
Caution
The ports labeled Ethernet, Console, and Auxiliary (AUX) are safety extra-low voltage (SELV) circuits.
SELV circuits should only be connected to other SELV circuits.
Note
RSP/RP cables are not available from Cisco, but they are available from any commercial cable vendor.
Note
To comply with the intra-building lightning surge requirements of Telecordia GR-1089-CORE, Issue II,
Revision 01, February 1999, you must use a shielded cable when connecting to the console, auxiliary,
and Ethernet ports. The shielded cable is terminated by shielded connectors on both ends, with the cable
shield material tied to both connectors.
3-23
Chapter 3
Connecting to the Console Port

The system console port on the RSP/RP is an RJ-45 receptacle for connecting a data terminal to perform
the initial configuration of the router. The console port requires a straight-through RJ-45 cable.
See RSP and RP Port Connection Guidelines, page 1-55 for additional information about the console
port.
Follow this procedure to connect a data terminal to the RSP/RP console port:
Step 1
Set your terminal to these operational values: 9600 bps, 8 data bits, no parity, 2 stop bits (9600 8N2).
Step 2
Power off the data terminal.
Step 3
Attach the terminal end of the cable to the interface port on the data terminal.
Step 4
Attach the other end of the cable to the RSP/RP console port.
Step 5
Power on the data terminal.
Connecting to the Auxiliary Port

The auxiliary port on the RSP/RP is a RJ-45 receptacle for connecting a modem or other data
communication equipment (DCE) device (such as another router) to the RSP/RP. The asynchronous
auxiliary port supports hardware flow control and modem control.
See RSP and RP Port Connection Guidelines, page 1-55 for additional information about the auxiliary
port.
Follow this procedure to connect an asynchronous serial device to the RSP/RP auxiliary port:
Step 1
Power off the asynchronous serial device.
Step 2
Attach the device end of the cable to the interface port on the asynchronous serial device.
Step 3
Attach the other end of the cable to the RSP/RP auxiliary port.
Step 4
Power on the asynchronous serial device.
Connecting to the Ethernet Management Ports

To connect cables to the RSP/RP management ports, attach Category 5 UTP cables directly to the
MGT LAN 0 and MGT LAN 1 RJ-45 receptacles on the RSP/RP.
See Management LAN Ports Connection Guidelines, page 1-57 for additional information about the
Ethernet management LAN ports.
Note
RJ-45 cables are not available from Cisco Systems; they are available from outside commercial cable
vendors. Use cables that comply with EIA/TIA-568 standards.
3-24
Chapter 3

Caution
Ethernet management ports are primarily used as Telnet ports into the Cisco ASR 9000 Series Router,
and for booting or accessing Cisco software images over a network to which an Ethernet port is directly
connected. We strongly caution you to consider the security implications of enabling routing functions
on these ports.
Note
The Ethernet interfaces on the RSP/RP are endstation devices only, not repeaters.
Follow these steps to connect an Ethernet cable to the RSP/RP RJ-45 Ethernet receptacle:
Step 1
Plug the cable directly into the RJ-45 receptacle.
Step 2
Connect the network end of your RJ-45 cable to a switch, hub, repeater, or other external equipment.

The router alarm connector, located on the RSP/RP front panel, is a 9-pin D-subconnector, labeled
Alarm Out (Figure 3-18).
Alarm Out Cable Connector
J.211
SYNC 0
BITS
J.211
SYNC 1
BITS
ALARM OUT
243257
Figure 3-18
Alarm Out cable connector
3-25
Chapter 3
Connecting Power to the Router
The alarm subconnector can be used to connect the router to an external site alarm maintenance system.
Any critical, major, and minor alarms generated by the router also energize alarm relays on the alarm
card and activate the external site alarm. The alarm relay contacts on the RSP/RP card consist of standard
common, normally open, and normally closed relay contacts that are wired to the Alarm Out connector
pins.
Table 1-8 lists the pin-to-signal correspondence between the connector pins and the alarm relay contacts.
Because alarm contact cables are entirely dependent on installation site circumstances, alarm connector
cables are not available from Cisco. For information about alarm connector wiring requirements and the
pinouts for the alarm connector interface, see Alarm Connection Guidelines, page 1-59.
Caution
Only safety extra-low voltage (SELV) circuits can be connected to the Alarm Out connector. Maximum
rating for the alarm circuit is 100 mA, 50 V.
Note
To comply with the intra-building lightning surge requirements of GR-1089-CORE, Issue II,
Revision 01, February 1999, you must use a shielded cable when connecting to the external alarm port
on the RSP/RP card. The shielded cable is terminated by shielded connectors on both ends, with the
cable shield material tied to both connectors.

Use the one of the following procedures to connect power to your router.
Caution
Connecting Power to an AC-Powered Router, page 3-26
Connecting Power to a DC-Powered Router, page 3-28
A router must be operated with all its power modules installed at all times for electromagnetic
compatibility (EMC).
Connecting Power to an AC-Powered Router

Follow these steps to connect the AC power cords to the router.
Note
Step 1
Connect each AC power supply to a dedicated power source (branch circuit). Each AC input
power supply operates at a nominal input level of 200 to 240 VAC. For more information on AC
power input levels, see Power Connection Guidelines, page 1-36.
Check that the power switch is set to the STANDBY (0) position.
On version 1 power trays, this switch is at the rear of the power tray.
On version 2 and version 3 power trays, this switch is at the front of the power tray.
Step 2
Check that the circuit breaker assigned to the AC power source you are connecting is set to OFF.
Step 3
Connect the permanent ground connection (central office grounding system) to the NEBS grounding
location on the router chassis.
3-26
Chapter 3

Caution
To ensure that power remains off while you are performing this procedure, lock-out/tag-out the circuit
breaker switch in the off (0) position until you are ready to turn it on.
Step 4
Plug the AC power cord into the receptacle at the rear of the AC power tray (see Figure 3-19 for the
version 1 power tray and Figure 3-20 for the version 2 and version 3 power tray).
Step 5
Close the retainer bracket to secure the AC power cord plug to the version 1 power tray receptacle. For
the version 2 and version 3 power tray, tighten the screw that clamps the AC power cord plug in place.
Typical AC Power Connections to an AC Power TrayVersion 1 Power System
Figure 3-20
Typical AC Power Connections to an AC Power TrayVersion 2 and Version 3 Power System
284278
243302
Figure 3-19
Step 6
Plug the other end of the AC power cord into the AC source receptacle.
3-27
Chapter 3
Step 7
Proceed to the Powering On the Router section on page 3-32.
Connecting Power to a DC-Powered Router

This section contains the procedures to connect the DC source power cables to a DC-powered router.
The color coding of source DC power cable leads depends on the color coding of the site DC power
source. Because there is no color code standard for source DC wiring, you must be sure that power
source cables are connected to the power module with the proper positive (+) and negative () polarity:
In some cases, the source DC cable leads might have a positive (+) or a negative () label. This is a
relatively safe indication of the polarity, but you must verify the polarity by measuring the voltage
between the DC cable leads. Be sure that the positive (+) and negative () cable leads match the
positive (+) and negative () labels on the power module when making the measurement.
Green (or green and yellow) cable typically indicates that it is a ground cable.
Caution
DC power modules contain circuitry to trip the breaker on the power module if the power module detects
a reverse polarity condition. No damage should occur from reverse polarity, but you should correct a
reverse-polarity condition immediately.
Note
The length of the cables depends on the location of your router in relation to the source of DC power.
These cables and the cable lugs used to attach the cables to the router chassis are not available from Cisco
Systems. They are available from any commercial cable vendor. For more information on site power and
source DC cable requirements, see Power Connection Guidelines, page 1-36.
Caution
To ensure that power remains off while you are performing this procedure, lock-out/tag-out the DC
circuit breaker switch in the off (0) position until you are ready to turn it on.
Follow these steps to connect the DC source power cables to a DC power tray:
Step 1
Verify that the power tray switch is set to the STANDBY (0) position.
Step 2
Remove the clear plastic safety covers that fit over the DC power connection terminal studs.
Step 3
Connect the DC power cables in the following order (see Figure 3-19 for the version 1 power system,
Figure 3-20 for the version 2 power system, and Figure 3-23 for the version 3 power system.
Step 4
Caution
a.
Ground cables first.
b.
Positive cables next.
c.
Negative cable last.
Repeat Step 3 for the other power modules installed in the tray.
To prevent injury and damage to the equipment, always attach the ground and source DC power cable
lugs to power tray terminals in the following order: (1) ground to ground, (2) positive (+) to positive (+),
(3) negative () to negative ().
3-28
Chapter 3

Caution
Typical Power Connections to a Power Tray for a Single DC Power ModuleVersion 1 Power System
243183
Figure 3-21
Do not overtighten the nuts that secure the DC power cables to the power tray terminals. Using the 7/16
hex socket and torque wrench the nuts should be tightened to a torque of 45 to 50 in-lb.
PWR A
48/60V PWR
RTN A+
48/60V RTN
Feed A, Slot M2
PWR B
48/60V PWR
RTN B+
48/60V RTN
Ground
Feed B, Slot M2
3-29
Chapter 3
Figure 3-22
Typical Power Connections to a Power Tray for a Single DC Power ModuleVersion 2

Power System
M3
M2
M1
M3
M2
344255
M1
PWR A
48/60V PWR RTN A+
48/60V RTN
Feed A, Slot M3
PWR B
48/60V PWR RTN B+
48/60V RTN
Feed B, Slot M3
3-30

PWR A
48/60V PWR RTN A+
48/60V RTN
Feed A, Slot M3
Typical Power Connections to a Power Tray for a Single DC Power ModuleVersion 3

Power System
PWR B
48/60V PWR RTN B+
48/60V RTN
364234
Figure 3-23
Feed B, Slot M3
Figure 3-24
Location of DC Power SwitchVersion 2 and Version 3 Power System
331402
Chapter 3
Power switch
Step 5
Replace the clear plastic safety covers over the connection terminal studs. Figure 3-24 shows the plastic
safety cover being installed over the version 2 DC power tray connection terminals. The plastic covers
for the version 2 DC power tray are similar.
Step 6
Proceed to Powering On the Router, page 3-32.
3-31
Chapter 3

Follow these steps to turn on power to an AC-powered or DC-powered router:
Step 1
Power on the circuit breaker to your power sources.
Step 2
Verify that the Power Input LED on each power module in the tray is lit.
Note
On the DC power tray, the Power Input LED is lit solid green if both DC feeds are valid and
blinks green if only a single DC feed is valid.
Step 3
Set the power tray switch for Feed A Slots M03 to the ON (1) position. For the feeds, see Figure 3-19
for the version 1 power system and Figure 3-22 for the version 2 power system, and Figure 3-23 for the
version 3 power system. For the locations of the power switch, see Figure 3-22 for the version 1 power
system, and Figure 3-24 for the version 2 and version 3 power systems.
Step 4
Verify that the Power Output LED on each power module in the tray is lit.
Step 5
Repeat Step 3 and Step 4 for Slots M03 for Feed B.
3-32
CH A P T E R

This chapter contains general troubleshooting information to help isolate the cause of any difficulties
you might encounter during the installation and initial startup of the system.
Although an overtemperature condition is unlikely at initial startup, environmental monitoring functions
are included in this chapter because they also monitor internal voltages.
Troubleshooting Overview, page 4-1
Troubleshooting the Power Subsystem, page 4-7
Troubleshooting the Route Processor Subsystem, page 4-19
Troubleshooting the Cooling Subsystem, page 4-32
Troubleshooting Overview
This section describes the methods used in troubleshooting the router. The troubleshooting methods are
organized according to the major subsystems in the router.
If you are unable to solve a problem on your own, you can contact a Cisco customer service
representative for assistance. Cisco customer service and technical support can be reached at:
http://www.cisco.com/en/US/support/tsd_cisco_worldwide_contacts.html
When you call, please have the following information ready:
Date you received the router and the chassis serial number (located on a label on the back of the
chassis).
Installed line cards and Cisco software release number:

Use the show version command to determine which line cards are installed and the Cisco
software release number, if possible.
Brief description of the symptoms and steps you have taken to isolate and solve the issue.
Maintenance agreement or warranty information.
4-1
Chapter 4
Troubleshooting Using a Subsystem Approach

To solve a system problem, try to isolate the problem to a specific subsystem. Compare current router
behavior with expected router behavior. Because a startup issue is usually attributable to one component,
it is most efficient to examine each subsystem, rather than trying to troubleshoot each router component.
Table 4-1 describes the subsystems for the Cisco ASR 9000 Series Routers:
Table 4-1
Subsystem Descriptions for the Cisco ASR 9000 Series Routers
Type of Subsystem
Power subsystem
Description
Up to 8 AC input or DC input power supply modules can

be installed in the Cisco ASR 9010 Router chassis.
Up to 4 AC input or DC input power supply modules

installed in the Cisco ASR 9006 Router chassis.



Chassis backplane power distribution The system transfers 54 VDC power from the power modules
to the chassis backplane and distributes it to all the cards
through the backplane connectors.
Processor subsystem
Includes the active Route Switch Processor (RSP) card (and

optional, redundant RSP card, if installed).
Up to eight line cards in the Cisco ASR 9010 Router, four line
cards in the Cisco ASR 9006 Router, and two line cards in the
Note
Processor subsystem
The RSP and line cards are equipped with onboard

processors. The RSP downloads a copy of the Cisco
software image to each line card processor. The system
uses an alphanumeric display on the active RSP to
display status and error messages, which can help in
troubleshooting.
Includes the active Route Processor (RP) card, standby

redundant RP card.
Up to 20 line cards in the Cisco ASR 9922 Router or 10 line
cards in the Cisco ASR 9912 Router.
Note
The RP and line cards are equipped with onboard

processors. The RP downloads a copy of the Cisco
software image to each line card processor. The system
uses an alphanumeric display on the active RP to
display status and error messages, which can help in
troubleshooting.
4-2
Chapter 4

Table 4-1
Subsystem Descriptions for the Cisco ASR 9000 Series Routers (continued)
Type of Subsystem
Description
Cooling subsystem
Consists of one or two fan trays, which circulate air through the
card cage to cool the cards, and two fans in each of the power
modules, which circulate cooling air through the power
module.

Cooling subsystem
Consists of four fan trays, which circulate air through the top
and bottom line card cages to cool the cards, and two fans in
each of the power modules, which circulate cooling air through
the power module.
Note
There are two types of image files, -P PIE files, and x86-based -PX PIE files. -P PIE files are for use on
Cisco ASR 9000 Series Routers with RSP route switch processors (RSP-4G and RSP-8G). -PX PIE files
are for use on the routers with RSP-440/RSP-440 Lite and RSP-880 route switch processors, and the
Cisco ASR 9922 Router and Cisco ASR 9912 Router route processors.
Normal Router Startup Sequence

You can generally determine when and where the router failed during the startup sequence by checking
the status LEDs on the power modules, and the alphanumeric displays on the RSP, RP, and line cards.
In a normal router startup sequence, the following sequence of events and conditions occur:
1.
The fan in each power module receives power and begins drawing air through the power supply.
The power module input power and output power indicators are on.
2.
The fans in the fan tray receive power and begin drawing air through the chassis.
The fan tray OK indicator is on.
3.
As the power-on and boot process progresses for the RSP/RP, the status of the RSP/RP appears on
the alphanumeric display on the front panel of the card.
4-3
Chapter 4
Identifying Startup Issues

Table 4-2 shows the contents of the alphanumeric displays on the various RSP/RP cards, as well as the
normal LED states on the power modules (AC or DC) and the fan tray after a successful system startup.
Note
Table 4-2
For the RSP/RP card to communicate properly to a power module in a power tray, the appropriate input
power should be present.
Alphanumeric Displays and LEDs at System Startup
Component
Type of Indicator
Display Contents/LED Status and Meaning
RSP card
Alphanumeric
display
INITCard is inserted and microcontroller is initialized

BOOTBoard is powered on and CPU is booting
IMEMStart initializing memory
IGENStart initializing the board
ICBCStart initializing communication with the microcontroller
PDxyLoading programmable devices
(x = FPGA, y = ROMMON)
PSTxPower on self test x
RMNAll tests are finished and ROMMON is ready for commands
LOADDownloading Minimum Boot Image (MBI) image to CPU
MBIStarting execution of MBI
IOXRCisco IOS XR software is starting execution
ACTVRSP role is determined to be active RSP
STBYRSP role is determined to be standby RSP
PREPPreparing disk boot
4-4
Chapter 4

Table 4-2
Alphanumeric Displays and LEDs at System Startup (continued)
Component
Type of Indicator
RSP-440
RSP-440 Lite
RSP-880 card
Alphanumeric
display

SCPIBoard is not plugged in properly
RSP-440/RSP 440-Lite
STIDCBC was unable to read slot ID pins correctly
PSEQCBC detected power sequencer failure
DBPOCBC detected an issue during board power up
KPWRCBC detected an issue during board power up
LGNPCBC detected an issue during board power up
LGNICBC detected an issue during board power up

LOADDownloading MBI image to CPU
RRSTROMMON is performing a soft reset after 5 consecutive MBI validation
requests timed out
MVBROMMON trying MBI validation boot
LDGThe RSP is loading (MBI started and card preparing for activity)
INCPThe software or configuration is incompatible with the RSP
OOSMThe RSP is in Out of Service, Maintenance mode
ACTVRSP role is determined to be active RSP
STBYRSP role is determined to be standby RSP
4-5
Chapter 4
Table 4-2
Component
Type of Indicator
RP card
RP2 card
Alphanumeric
display

SCPIBoard is not plugged in properly
RRSTROMMON is performing a soft reset after 5 consecutive MBI validation
requests timed out
LDGThe RP is loading (MBI started and card preparing for activity)
INCPThe software or configuration is incompatible with the RP
OOSMThe RP is in Out of Service, Maintenance mode
ACTVRP role is determined to be active RP
STBYRP role is determined to be standby RP
Line Cards
Status LED
Green: The line card is enabled and ready for use.
AC Power
Modules
Power status LEDs
Input power indicator on (green): Input AC power OK.

Output power indicator on (green): Output DC power OK.
Fault LED off (red): No fault is present.
The correct power module voltages are present and no faults have been detected.
4-6
Chapter 4

Troubleshooting the Power Subsystem
Table 4-2
Component
Type of Indicator
DC Power
Modules
Power status LEDs
Input power indicator on (green): Input DC power OK.

On the DC power tray, the Power Input LED is lit solid green if both DC feeds
are valid and blinks green if only a single DC feed is valid.
Output power indicator on (green): Output DC power OK.
Fault LED off (red): No fault is present.
The correct power module voltages are present and no faults have been detected.
Fan Trays
Fan tray status LED
Green LED on: Fan Tray OK.

The fan tray fans are operating correctly.

This section contains information to troubleshoot the power subsystems:
Note
Troubleshooting the AC Input Power Subsystem, page 4-7
Troubleshooting the DC Input Power Subsystem, page 4-12
Troubleshooting the Power Distribution System, page 4-18
For the RSP/RP card to communicate properly to a power module in a power tray, input power to at least
one of the three power modules in the power tray should be present.
Troubleshooting the AC Input Power Subsystem

AC input power modules are monitored for internal temperature, voltage, and current load by the
RSP/RP. If the router detects an extreme condition, it generates an alarm and logs the appropriate
warning messages on the console.
Figure 4-1 shows the status indicators for the version 1 power module, Figure 4-2 shows the status
indicators for the version 2 power module, and Figure 4-3 shows the status indicators for the version 3
AC power module. The indicator definitions follow the two figures.
4-7
Chapter 4
Version 1 Power Module Status Indicators
242986
Figure 4-1
1 Input power LED
ON continuously when the input voltage is present and within the correct range
BLINKING when the input voltage is out of acceptable range
On the DC power tray, the Power Input LED is lit solid green if both DC feeds are
valid and blinks green if only a single DC feed is valid.
OFF when no input voltage is present
2 Output power LED ON when the power module output voltage is present
BLINKING when the power module is in a power limit or overcurrent condition
3 Fault LED
ON to indicate that a power module failure has occurred
4-8

Figure 4-2
Version 2 Power Module Power Module Status Indicators
284405
Chapter 4
1
2
3
1 Input power LED
3 Fault LED
4-9
Chapter 4
Figure 4-3
Version 3 AC Power Module Status Indicators
1
2
363718
1 Input power LED
3 Fault LED
Follow these steps to troubleshoot the AC power module if it is not operating properly.
Step 1
Step 2
Make sure the power module is seated properly by ejecting and reseating the power module. Check that:
Latch on the door/ejector lever is locked securely.
Power switch on the power tray is set to the ON (1) position.
Make sure the router is powered on and that all power cords are connected properly. Check that the:
4-10
Chapter 4

Step 3
Power cords plugged into the power tray receptacles are secured in place with their retention clips.
Power cords at the power source end are securely plugged into their own AC power outlets.
Source AC circuit breaker is switched on.
Check the power supply status LED indicators:
Input power LED (green)Indicates that the AC power input is operating normally, and the source
AC input voltage of 200 to 240 VAC is within the nominal operating range.
If the input power LED is blinking, the input voltage is out of acceptable range. Verify that each AC
power source is operating in the nominal range of 200 to 240 VAC.
Note
On the DC power tray, the Power Input LED is lit solid green if both DC feeds are valid and
blinks green if only a single DC feed is valid.
Output power LED (green)Indicates that the DC power output is operating normally and the
54 VDC output voltage to the backplane are within the nominal operating range. This indicator
lights only when the power switch at the rear of the power tray is set to the ON (1) position.
If the Output power LED remains off after checking all the power sources, replace the power
supply with a spare. If the spare power module does not work, troubleshoot the power tray in
which the module is plugged.
If the output power LED is blinking, the power module is in a power limit or overcurrent
condition. Make sure that each power cord is connected to a dedicated AC power source. Verify
that each AC power source is operating in the nominal range of 200 to 240 VAC and is supplying
a minimum service of 20 A, North America (or 13 A, international).
Fault LED (red)Indicates that the system has detected a fault within the power supply. This
indicator remains off during normal operation. If the fault LED is on:
If your system has more than one power tray (Cisco ASR 9010 Router,
Cisco ASR 9922 Router, and Cisco ASR 9912 Router) with power modules installed for
redundancy, you can toggle the power switch at the rear of the first power tray off and then on.
If the fault LED remains on after several attempts to power it on, replace the power module with
a spare.
If the spare power module also fails, the problem could be a faulty power tray backplane
connector. Power off the router and contact a Cisco service representative for assistance.
Verify that the power module fans are operating properly.
Verify that the fan tray is operating properly.
If the power module fans and the fan trays are operating properly, replace the existing power module
with a spare.
Caution
Because the AC input power subsystems use redundant power modules, a problem with the DC output
voltage to the backplane from only one power module should not affect router operation. When the router
is equipped with two AC power supplies, it powers on and operates even if one power supply fails.
However, complete router functionality may be affected depending on the system load.
4-11
Chapter 4
Troubleshooting the DC Input Power Subsystem

DC input power supplies are monitored for internal temperature, voltage, and current load by the
RSP/RP. If the router detects an extreme condition, it generates an alarm and logs the appropriate
warning messages on the console.
Figure 4-1 shows the status indicators for the version 1 power module, Figure 4-2 shows the status
indicators for the version 2 power module, and Figure 4-4 shows the status indicators for the version 3
DC power module. The indicator definitions follow the two figures.
Figure 4-4
Version 3 DC Power Module Status Indicators
1
2
363719
4-12
Chapter 4

1 Input power LED
3 Fault LED
Troubleshooting a DC Power Module

Follow these steps to troubleshoot a DC power module if it is not operating properly.
Step 1
Step 2
Step 3
Make sure the power module is seated properly by ejecting and reseating the power module. Check that:
Latch on the door/ejector lever is locked securely.
Power switch on the power tray is set to the ON (1) position.
Make sure the router is powered on and that all power cords are connected properly. Check that the:
Power cables are securely attached to their power module terminal studs.
Power cables are securely attached at the DC source end.
Source DC circuit breaker is switched on.
Check the power supply status LED indicators:
Input power LED (green)Indicates that the DC power input is operating normally, and the source
DC input voltage is within the nominal operating range of 40 to 72 VDC.
If the input power LED is blinking, input connections to the power module are loose or not
connected, or the input voltage is below the minimum. Verify that DC power from the source is
operating in the nominal range of 40 to 72 VDC.
Note
On the DC power tray, the Power Input LED is lit solid green if both DC feeds are valid
and blinks green if only a single DC feed is valid. Check the input connections to the
power module.
If the indicator is still flashing after you perform the above checks, replace the power module.
Output power LED (green)Indicates that the DC power output is operating normally, and the
54 VDC output voltage to the backplane is within the nominal operating range. This indicator
lights only when the power switch at the rear of the power tray is set to the ON (1) position.
If the output power LED remains off after checking all the power sources, replace the power
module with a spare. If the spare power module does not work, troubleshoot the power tray in
which the module is plugged.
If the output power LED is blinking, the power module is in a power limit or overcurrent
condition. Make sure that each power cable is connected to a dedicated DC power source. Verify
that each DC power source is operating in the nominal range of 40 to 72 VDC.
4-13
Chapter 4
Fault LED (red)Indicates that the system has detected a fault within the power supply. This
indicator remains off during normal operation. If the fault LED is on, check the following:
If your system has more than one power tray (Cisco ASR 9010 Router,
Cisco ASR 9922 Router, and Cisco ASR 9912 Router) with power modules installed for
redundancy, you can toggle the power switch at the rear of the first power tray off and then on.
If the fault LED is still on, eject and reseat the power module. If the fault LED remains on after
several attempts to power it on, replace the power module with a spare.
If the spare power module also fails, the problem could be a faulty power tray backplane
connector. Power off the router and contact a Cisco service representative for assistance.
Verify that the power module fans are operating properly.
Verify that the fan tray is operating properly.
If the power module fans and the fan trays are operating properly, replace the faulty power
module with a spare.
Caution
Because there are redundant power modules, a problem with the DC output voltage to the backplane
from only one power module should not affect router operation. When the router is equipped with two
DC power supplies, it powers on even if one power supply fails. However, complete router functionality
may be affected depending on the system load.
Additional Power Subsystem Troubleshooting Information

This section contains additional troubleshooting information to help you isolate the cause of a power
problem.
Obtaining Temperature and Environmental Information

If both the RSP/RP and fan trays are operating, all internal correct DC voltages are present.
Enter the show environment command at the router admin prompt to display temperature and voltage
information for each installed card, fan tray, and power module as shown in this example:
RP/0/RSP0/CPU0:router(admin) #show environment
Temperature Information
--------------------------------------------R/S/I
Modules
Inlet
Temperature
(deg C)
Hotspot
Temperature
(deg C)
0/RSP0/*
host
25.3
41.6
host
29.2
30.0
host
35.0
46.6
host
21.2
20.8
0/0/*
0/1/*
0/FT0/*
4-14
Chapter 4

0/FT1/*
host
22.0
21.5
Voltage Information
--------------------------------------------R/S/I
Modules Sensor
0/RSP0/*
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
(mV)
VP3P3_CAN
VP2P5
VP3P3
VP1P2
VP1P5
VP1P8
VP5P0
VP7P0
VP2P5_DB
VP1P8_DB
VP1P5_DB
VP1P2_DB
VP0P75_DB
VP1P05_DB
VP1P8_ENSO
VP1P0_SAC0_VDDA
VP1P0_SAC0_VDDD_VDDACM
VP1P2_SERDES_PLL_LGN
VP1P0_SAC1_VDDD_VDDACM
VP1P0_SAC1_VDDA
VP1P0_SAC1_VDD
VP1P0_SAC0_VDD
VP1P0_DAO
VP1P0_KAW_LDO
VP1P0_MGTVCC_DAO
VP1P2_SERDES_PLL_DAO
VP1P0_SKT_IO
VP1P0_SKT_CORE
VP1P9_LDO
VP1P8_10GPHY_LDO
VP1P2_10GPHY_01
VP0P75_TMX_VTT
VP3P3_OCXO
VP1P8_OCXO
VP1P0_ARB
Margin
3300
2499
3299
1199
1500
1800
5000
6999
2499
1800
1500
1199
750
1050
1800
1000
999
1199
999
999
1000
1000
999
1000
1000
1200
1000
1000
1900
1800
1200
743
3300
1799
999
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
10552
4939
3275
3303
2515
1803
1203
1795
881
1195
1196
1806
1504
1499
1051
749
754
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
0/0/*
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
IBV
5.0V
VP3P3_CAN
3.3V
2.5V
1.8VB
1.2VB
1.8VA
0.9VB
1.2V_LDO_BRG0
1.2V_LDO_BRG1
1.8VC
1.5VB
1.5VA
1.1V(1.05V_CPU)
0.75VA
0.75VB_0.75VC
4-15
Chapter 4
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
1.1VB
1.2V_TCAM0
1.2V_TCAM1
1.0V_Bridge_LDO
1.0VB
0.75VD_and_0.75VE
1.2V_TCAM2
1.2V_TCAM3
1.5VC
1.8VD
1.1VC
ZARLINK_3.3V
ZARLINK_1.8V
1.2V_DB
3.3V_DB
2.5V_DB
1.5V_DB
1.8V_DB
5.0V_XFP_DB
1.2VB_DB
1101
1203
1202
995
1046
755
1208
1203
1507
1793
1105
3284
1810
1200
3320
2498
1493
1827
5034
1226
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
host
IBV
5.0V
VP3P3_CAN
3.3V
2.5V
1.8VB
1.2VB
1.8VA
0.9VB
1.2V_LDO_BRG0
1.2V_LDO_BRG1
1.8VC
1.5VB
1.5VA
1.1V(1.05V_CPU)
0.75VA
0.75VB_0.75VC
1.1VB
1.2V_TCAM0
1.2V_TCAM1
1.0V_Bridge_LDO
1.0VB
0.75VD_and_0.75VE
1.2V_TCAM2
1.2V_TCAM3
1.5VC
1.8VD
1.1VC
ZARLINK_3.3V
ZARLINK_1.8V
1.2V_DB
3.3V_DB
2.5V_DB
1.5V_DB
10460
4920
3283
3294
2510
1804
1203
1794
882
1191
1194
1816
1508
1497
1054
749
755
1104
1205
1207
995
1047
753
1207
1199
1503
1805
1102
3272
1811
1197
3318
2540
1511
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
n/a
0/1/*
4-16
Chapter 4

LED Information
--------------------------------------------R/S/I
Modules
0/RSP0/*
host
host
host
host
LED
Status
Critical-Alarm
Major-Alarm
Minor-Alarm
ACO
Off
Off
Off
Off
Fan Information
--------------------------------------------Fan speed (rpm):
FAN0
FAN1
FAN2
FAN3
FAN4
FAN5
6990
7020
6960
6900
0/FT0/*
7080
7020
0/FT1/*
6900
6900
7110
6960
6900
Power Supply Information
---------------------------------------------
7020
R/S/I
Modules Sensor
Watts
Status
host
3000
Ok
0/PM0/*
PM
Power Shelves Type: AC

Total Power Capacity:
Usable Power Capacity:
Supply Failure Protected Capacity:
Worst Case Power Used:
3000W
3000W
0W
1910W
Slot
---0/RSP0/CPU0
0/RSP1/CPU0
0/0/CPU0
0/1/CPU0
0/FT0/SP
0/FT1/SP
Max Watts
--------250
250
375
375
330
330
Worst Case Power Available:

Supply Protected Capacity Available:
(default)
(default)
(default)
1090W
Not Protected
4-17
Chapter 4
Troubleshooting the Power Distribution System

The power distribution system consists of:
AC or DC power modules, which supply 54 VDC to the backplane.
Chassis backplane, which carries voltage to chassis components.
DC-to-DC converters, which convert 54 VDC from the backplane to the correct voltages required
by the line cards.
Follow these steps to troubleshoot the power distribution system:

Step 1
Check each power module to make sure that:
Power module door is fully closed and properly secured by its latch.
Green Input Power LED is on.
Green Output Power LED is on.
Red Fault LED is off.
If the power modules meet the above criteria, then the correct source power is present and within
tolerance and output DC power is present. The power modules are functioning properly.
Step 2
Make sure the fan trays are operating:
If the fan trays are functioning, then the 54 VDC from the chassis backplane and the cables from
the backplane to the fan trays are functioning properly.
If one or both fan trays are not functioning, there may be a problem with either the fan trays
themselves, or the 54 VDC power supplied to the fan trays. Eject and reseat the fan trays.
If a fan tray is still not operating, there could be a problem with the fan tray controller card or cable.
Replace the fan tray.
Contact your Cisco representative if replacing a fan tray or both fan trays does not fix the problem.
4-18
Chapter 4

Troubleshooting the Route Processor Subsystem

The router processor subsystem consists of the route processor located on the RSP card. The RSP and
the line cards each have the same onboard CPU serving as the main processor. The Controller Area
Network (CAN) microcontroller processor monitors the environment and controls the onboard
DC-to-DC converters.
Note
A minimally configured router must have an RSP/RP installed in RSP slot 0 or RP slot 0 of the card cage
to operate. If the router is equipped with a redundant RSP/RP, the redundant RSP/RP must be installed
in RSP slot 1 or RP slot 1 of the card cage.
This section contains information to troubleshoot the route processor subsystem, including:
Route Processor Overview, page 4-19
RSP and RP Front Panel Indicators, page 4-25
Troubleshooting RSP and RP Cards, page 4-29
Fabric Card Front Panel Indicator, page 4-31
Troubleshooting Line Cards and Modular Port Adapters, page 4-31
Route Processor Overview

The CPU on the RSP/RP card provides chassis control and management, boot media functionality,
telecom timing and precision clock synchronization, communication to the line cards through the
backplane Ethernet network, and power control through the CAN bus. In addition, the CPU on the
RSP/RP card also runs the routing protocols.
The RP2 card has more processing power than the earlier RP. It also doubles the amount of storage and
supported memory as well as the memory bandwidth. This provides the path to scale the number of
routes up in this generation. In addition the internal control plane bandwidth has been scaled up to allow
better control of the linecards as the network bandwidth increases. Figure 4-8 identifies the ports and
LEDs on the RP card front panel. Figure 4-9 identifies the ports and LEDs on the RP2 card front panel.
Figure 4-5 identifies the ports and LEDs on the RSP card front panel.
Figure 4-6 identifies the ports and LEDs on the RSP-440 and RSP-440 Lite card front panel.
Figure 4-7 identifies the ports and LEDs on the RSP-880 card front panel.
Figure 4-8 identifies the ports and LEDs on the RP card front panel.
Figure 4-9 identifies the ports and LEDs on the RP2 card front panel.
4-19
Chapter 4
Figure 4-5
RSP Card Front Panel
ACT
MGT LAN 0
LINK
ACT
MGT LAN 1
LINK
CONSOLE
2
AUX
J.211
SYNC 0
BITS
J.211
SYNC 1
BITS
ALARM OUT
KEEP CLOSED
COMPACT FLASH ACCESS
ACO
6
7
LAMP
TEST
FAIL
SYNC
CRIT
HDD
MAJ
CF
MIN
ACO
8
243091
A9K-RSP-4G
1 Management LAN ports
5 Compact Flash type I/II
2 Console and Auxiliary (AUX) ports
6 Alarm Cutoff (ACO) and Lamp Test push buttons
3 Sync (BITS and J.211) ports
7 Eight discrete LED indicators
4 Alarm Out DB9 Connector
8 LED matrix display
4-20
Chapter 4

Figure 4-6
RSP-440 and RSP-440 Lite Card Front Panel
J211
SYNC 0
BITS
J211
SYNC 1
BITS
SFP + 0
ACT
IEEE 1588
LINK
SFP + 1
ICS0
GPS INTERFACE
ICS1/TOD
10MHz 1PPS
ALARM OUT
6
7
J.211
MGT LAN 0
BITS
J.211
MGT LAN 1
BITS
CONSOLE
9
AUX
10
A9K-RSP440-SE
330841
12
T
UL
FA PS
D
G
SS
FC
J
IT
MIN
CR
MA
O
NC
IL
SY
FA
AC
11
ACO
LAMP
TEST
SYNC (BITS/J.211) ports
External USB port
SFP/SFP+ ports
Management LAN ports
Service LAN port
Console and Auxiliary (AUX) ports
ToD port
10
Alarm Cutoff (ACO) and Lamp Test push buttons
10 MHz and 1 PPS indicators
11
Eight discrete LED indicators
Alarm Out DB9 connector
12
LED matrix display
4-21
Chapter 4
Figure 4-7
RSP-880 Card Front Panel
2
3
4
5
6
7
8
9
10
11
12
363579
13
SFP/SFP+ ports
CMP port
Service LAN port
10
Console and Auxiliary (AUX) ports
Inter Chassis Sync ports and ToD port
11
12
Eight discrete LED indicators
13
LED matrix display
External USB port
4-22
Chapter 4

Figure 4-8
RP Card Front Panel
1
2
3
4
5
6
7
8
9
10
11
12
344073
13
External USB port
SFP/SFP+ ports
IEEE 1588 port
10
CONSOLE and AUX ports
Inter-chassis nv Sync0
11
Inter-chassis nv Sync1 GPS ToD
12
Nine discrete LED indicators
13
LED matrix display
4-23
Chapter 4
Figure 4-9
RP2 Card Front Panel
1
2
3
4
5
6
7
8
9
10
11
363906
12
13
SFP/SFP+ ports
CMP Port
IEEE 1588 port
10
CONSOLE and AUX ports
Inter-chassis nv Sync0 and 1
11
12
Nine discrete LED indicators
13
LED matrix display
External USB port
4-24
Chapter 4

RSP and RP Front Panel Indicators
LED Display Definitions, page 4-25
Compact Flash and Status LEDs, page 4-27
Ethernet Ports and Status LEDs, page 4-27
Auxiliary and Console Ports, page 4-28
Alphanumeric Message Displays, page 4-28
Flash Memory, page 4-29
LED Display Definitions

The RSP card has eight discrete LED indicators and an LED dot-matrix display for system information.
The RSP-440, RSP-440 Lite, and RSP-880 have nine discrete LED indicators, a LED dot-matrix display
for system information, and three USB-specific LEDs. The RP has nine discrete LED indicators and a
LED dot-matrix display for system information.
Table 4-3 describes the discrete LEDs and the three USB LEDs on the RSP, RSP-440, RSP-440 Lite, and
RSP-880 cards. Table 4-4 describes the discrete LED definitions for the RP and RP2 cards.
Table 4-3
RSP, RSP-440, RSP-440 Lite, RSP-880 Discrete LED Display Definitions
Indicator (Label)
Color
Description
Power Fail (FAIL)
Red
Standby Power Fail LED. The LED is turned off by the CAN bus controller
after it is up and running.
Off
Standby power is normal.
Red
Critical Alarm LED. A critical alarm has occurred.
Off
(Default after reset)
No critical alarm has occurred.
Red
Major alarm LED. A major alarm has occurred.
Off
No major alarm has occurred.
Amber
Minor alarm LED. A minor alarm has occurred.
Off
No minor alarm has occurred.
Green
System timing is synchronized to an external timing source.
Amber
System timing is free running.
Off
LED never turns off.
Amber
Alarm Cutoff has been enabled. The ACO push button was pressed after at
least one alarm has occurred.
Off
Alarm Cutoff is not enabled.
Green
Hard Disk Drive is busy/active. The LED is driven by the SAS controller.
Off
Hard Disk Drive is not busy/active
Critical Alarm (CRIT)
Major Alarm (MAJ)
Minor Alarm (MIN)
Synchronization
(SYNC)
Alarm Cutoff (ACO)
Internal Hard Disk

Drive (HDD)
[RSP only]
4-25
Chapter 4
Table 4-3
RSP, RSP-440, RSP-440 Lite, RSP-880 Discrete LED Display Definitions (continued)
Indicator (Label)
Color
Description
External Compact
Flash (CF)
Green
Compact Flash is busy/active.
Off
Compact Flash is not busy/active.
[RSP only]
Green
Internal Solid State
Hard Disk Drive (SSD)
Internal Solid State Hard Disk Drive (SSD0) is busy/active. The LED is
driven by the SSD/SAS controller.
RSP-440/RSP-440 Lite Off

RSP-880
Internal Solid State Hard Disk Drive is not busy/active.
GPS
GPS interface provisioned and ports are turned on. ToD, 1 PPS, 10 Mhz are
all valid.
Green
RSP-440/RSP-440 Lite
Off
RSP-880
Green
External USB 2.0

RSP-880
Internal USB 2.0 A
Green

RSP-880
Internal USB 2.0 B
Green

RSP-880
Table 4-4
Either the interface is not provisioned, or the ports are not turned on. ToD, 1
PPS, 10 Mhz are not valid.
External USB is busy/active.
External USB is not busy/active.
Internal USB is busy/active.
Internal USB is not busy/active.
Internal USB is busy/active.
Internal USB is not busy/active.
RP and RP2 Discrete LED Display Definitions
Indicator (Label)
Color
Description
Power Fail
(FAIL)
Red
(Default after power on)
Standby Power Fail LED. The LED is turned off by the CAN bus controller
after it is up and running.
Off
Standby power is normal.
Critical Alarm
(CRIT)
Red
Critical Alarm LED. A critical alarm has occurred.
Off
No critical alarm has occurred.
Major Alarm
(MAJ)
Red
Major alarm LED. A major alarm has occurred.
Off
No major alarm has occurred.
Minor Alarm
(MIN)
Amber
Minor alarm LED. A minor alarm has occurred.
Off
No minor alarm has occurred.
Alarm Cutoff
(ACO)
Amber
Alarm Cutoff has been enabled. The ACO push button was pressed after at
least one alarm has occurred.
Off
Alarm Cutoff is not enabled.
4-26
Chapter 4

Table 4-4
RP and RP2 Discrete LED Display Definitions (continued)
Indicator (Label)
Color
Description
Synchronization
(SYNC)
Green
System timing is synchronized to an external timing source including

IEEE 1588.
Amber
System timing is free running.
Off
LED never turns off.
Internal Solid
State Hard Disk
Drive (SSD)
Green
Internal Solid State Hard Disk Drive (SSD0) is busy/active. The LED is
driven by the SSD/SAS controller.
Off
Internal Solid State Hard Disk Drive is not busy/active.
FC Fault
Amber
A fault has occurred on any or all of the FCs installed. This LED will be on
during the boot phase of the FC. This LED will be turned off by the
Controller Area Network (CAN) bus controller after it is up and running.
Off
All FCs are booted up and ready.
Green
GPS interface provisioned and ports are turned on. ToD, 1 PPS, 10 Mhz are
all valid.
Off
Either the interface is not provisioned, or the ports are not turned on. ToD, 1
PPS, 10 Mhz are not valid.
GPS
Compact Flash and Status LEDs

One compact flash slot provides the RSP with additional flash memory capacity. All combinations of
different flash devices are supported by the RSP. You can use ATA flash disks, Type 1 or Type 2 linear
flash memory cards, or a combination of the two.
Note
The RSP card only supports +5.2 VDC flash memory devices. It does not support +3.3 VDC PCMCIA
devices.
Note
The RSP-440, RSP-440 Lite, RSP-880, and RP cards do not have a compact flash slot.
The slot has an eject button (located behind the cover) to remove a flash card from the slot.
Ethernet Ports and Status LEDs

The RSP/RP cards have two 8-pin media-dependent interface (MDI) RJ-45 Management LAN ports for
100 Mbps and 1000Mbps Ethernet connections. These ports are labeled MGT LAN 0 and MGT LAN 1.
The transmission speed of the Ethernet port is not user-configurable. You set the speed through an
autosensing scheme on the RSP/RP, which determines the speed by the network that the Ethernet port is
connected to. However, even at an autosensed data transmission rate of 100 Mbps, the Ethernet port can
only provide a usable bandwidth of substantially less than 100 Mbps. You can expect a maximum usable
bandwidth of approximately 12 Mbps when using an Ethernet connection.
The following LEDs on the front panel indicate traffic status and port selection (Figure 4-10):
4-27
Chapter 4
LINKIndicates link activity.
ACTIndicates which Ethernet port is selected (ETH 0 or ETH 1).
Note
Because both ports are supported on the RSP/RP card, MGT LAN 0 is always on. MGT LAN 0
lights when it is selected.
Management LAN Port Activity LEDs
243165
Figure 4-10
Auxiliary and Console Ports

The auxiliary and console ports on the RSP/RP are EIA/TIA-232 (also known as RS-232) asynchronous
serial ports connect external devices to monitor and manage the system:
Auxiliary portRJ-45 interface that supports flow control and is often used to connect a modem, a
channel service unit (CSU), or other optional equipment for Telnet management.
Console portReceptacle (female) that provides a RJ-45 interface for connecting a console
terminal.
Alphanumeric Message Displays

The alphanumeric message displays are organized in one row of four LED characters (see callout 8 in
Figure 4-5 for the RSP card, callout 12 in Figure 4-6 for the RSP-440 and RSP-440 Lite cards, callout
13 in Figure 4-7 for the RSP-880 card, callout 13 in Figure 4-8 for the RP card, and callout 13 in
Figure 4-9 for the RP2 card.
The alphanumeric message displays show router status messages during the boot process and after the
boot process is complete:
During the boot process, the message displays are controlled directly by the CAN microcontroller.
After the boot process, the message displays are controlled by Cisco IOS XR software (through the
CAN bus).
Cisco IOS XR System Error Message Reference Guide
The alphanumeric message displays also provide information about different levels of system operation,
including the status of the RSP/RP, router error messages, and user-defined status and error messages.
Note
For a list of all system and error messages, see the Cisco IOS XR System Error Message Reference Guide
4-28
Chapter 4

Flash Memory
You can use the flash memory on the RSP card to store multiple Cisco IOS XR software and microcode
images that you can use to operate the router. You can download new images to flash memory over the
network (or from a local server) to replace an existing image or to add it as an additional image. The
router can be booted (manually or automatically) from any of the stored images in flash memory.
Flash memory also functions as a Trivial File Transfer Protocol (TFTP) server to allow other servers to
boot remotely from the stored images, or to copy them into their own flash memory.
The system uses two types of flash memory:
Onboard flash memory (bootflash)Contains the Cisco IOS XR boot image
Compact flash memory disks (or cards)Contains the Cisco IOS XR software images
Note
The RSP-440, RSP-440 Lite, RSP-880, and RP cards do not have a compact flash slot.
Table 4-5 lists supported compact flash disk sizes and Cisco part numbers.
Table 4-5
Supported Compact Flash Disk Sizes
Compact Flash Disk Size
Part Number
1 GB
16-3204-01
Troubleshooting RSP and RP Cards

When the router is powered on, the alphanumeric display on the RSP indicates the following sequence:
INITCard is inserted and microcontroller is initialized.
BOOTBoard is powered on and CPU is booting.
IMEMStart initializing memory.
IGENStart initializing the board.
ICBCStart initializing communication with the microcontroller.
PDxyLoading programmable devices (x = FPGA, y = ROMMON).
PSTxPower on self test x.
RMNAll tests are finished and ROMMON is ready for commands.
LOADDownloading Minimum Boot Image (MBI) image to CPU.
MBIStarting execution of MBI.
IOXRCisco IOS-XR software is starting execution.
ACTVRSP role is determined to be active RSP.
STBYRSP role is determined to be standby RSP.
PREPPreparing disk boot.
4-29
Chapter 4
When the router is powered on, the alphanumeric display on the RSP-440, RSP-440 Lite, RSP-880 and
RP indicates the following sequence:
RSP-440 and RSP-440 Lite Only
UPWRUser requested power off (not applicable for RSP-880 and RP2)
TEMPOver temperature
CPUCPU communication failure (not applicable for RSP-880 and RP2)
RRSTROMMON is performing a soft reset after 5 consecutive MBI validation requests timed out
LDGThe RSP/RP is loading (MBI started and card preparing for activity)
INCPThe software or configuration is incompatible with the RSP/RP
OOSMThe RSP/RP is in Out of Service, Maintenance mode
ACTVRSP/RP role is determined to be active RSP/RP
STBYRSP/RP role is determined to be standby RSP/RP
You can use the alphanumeric display to isolate a problem with the RSP:
Alphanumeric display is powered directly from the CAN microcontroller on the RSP card through
the chassis backplane:
If the alphanumeric display is not operating, the CAN microcontroller may be malfunctioning.
If the CAN microcontroller is operating, the alphanumeric display could be on even if the RSP
failed to power on.
If the alphanumeric display is not operating, but the power modules and the fan trays are operational,
the RSP may not be installed properly, or the +5 VDC output from the chassis backplane may be
faulty:
Make sure that the system is powered on.
Initialize the RSP card by ejecting it from the chassis backplane and then reseating it.
4-30
Chapter 4

If the alphanumeric display is operating, check the meaning of the messages (see Table 4-6 for the
RSP).
When the DC-to-DC converters are powered on by the CAN microcontroller, the begins the RSP
boot process and displays various status messages. Some messages appear briefly; while others
appear for several seconds. If the messages appear to stop at a particular point, the boot process may
be halted:
Make a note of the message.
Turn off power to the router, then turn on the power again to reset the router and start the boot
process. If the router halts again, replace the RSP (see Removing and Replacing Cards from the
Chassis, page 5-25).
Table 4-6
Troubleshooting Using the RSP Alphanumeric Display Messages
Message
Description
PST1
Failed DDR RAM memory test
PST2
Failed FPGA image CRC check
PST3
Failed board type and slot ID verification
Fabric Card Front Panel Indicator

The front panel of the fabric card (FC) has one tri-color LED indicator for system information.
Table 4-7 lists the display definitions of the discrete LED on the FC front panel.
Table 4-7
Fabric Card LED Display Definitions
Indicator (Label)
Color
Description
Power Fail
(FAIL)
Green
FC powered on and FPGA is programmed.

Note
Red
Fabric Data Link failure is not detected so LED remains green.

Monitor CLI messages for status.
Fault or malfunction in FC power up or FPGA programming.

Note
Once any ejector lever release button is pushed in, the FC must be
physically removed and reinserted (OIR) to restart the FC. During
this time before the FC is restarted, the LED is red.
Amber
FC is powered on but fabric not active.
Off
FC is powered off through the CLI.
Troubleshooting Line Cards and Modular Port Adapters

See the Cisco ASR 9000 Series Aggregation Services Router Ethernet Line Card Installation Guide for
information about troubleshooting line cards and modular port adapters (MPA).
4-31
Chapter 4
Troubleshooting the Cooling Subsystem
Monitoring Critical, Major, and Minor Alarm Status

The alarms can warn of:
Overtemperature condition on a component in the card cage
Fan failure in a fan tray
Overcurrent condition in a power supply
Out-of-tolerance voltage on one of the cards
Insertion count for an RSP card, RP, card, FC, or LC has reached a specified threshold. For more
information on OIR insertion counts, see OIR Monitoring, page 5-3.
The alarm LEDs are controlled by the CAN microcontroller software, which sets the threshold levels for
triggering the different stages of alarms.
The RSP/RP card continuously polls the system for temperature, voltage, current, and fan speed values.
If a threshold value is exceeded, the RSP/RP sets the appropriate alarm severity level on the alarm card,
which lights the corresponding LED, and energizes the appropriate alarm display relays to activate any
external audible or visual alarms wired to the alarm display. The RSP/RP also logs a message about the
threshold violation on the system console.
Note
If one or more of the alarm LEDs is on, check the system console for messages describing the alarm.

You may need to troubleshoot the cooling subsystem if an overtemperature condition occurs. The
cooling subsystem of the router consists of a fan tray in the chassis and a fan in each of the power
supplies. The fan tray and the power supply fans circulate air to maintain acceptable operating
temperatures within the router.
Caution
When troubleshooting the fan trays, never unplug all the fan trays at the same time.
Chassis Cooling Requirements, page 4-32
Power Module Fans, page 4-34
Fan Tray Operation, page 4-33
Power Module Fans, page 4-34
Overtemperature Conditions, page 4-34
Isolating Cooling Subsystem Problems, page 4-35
Chassis Cooling Requirements

The Cisco ASR 9000 Series supports version 1 and version 2 fan trays. Version 2 high-speed fans provide
additional cooling for new generation line cards that draw more power and generate more heat. Table 4-8
lists the chassis cooling requirements for these cards.
4-32
Chapter 4

Table 4-8
Chassis Cooling Requirements for Next Generation Line Cards
Mod200
(1xNPU),
2x100GE EP
Chassis Type and Fan Tray
4x100GE
8x100GE
Mod200 (1xNPU)
Low density EP 20x10GE
Cisco ASR 9922, V2 fan tray
-5 to 50C
0 to 1800 m
-5 to 50 C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
Cisco ASR 9912, V1 fan tray
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
Cisco ASR 9910, V2 fan tray, low

power optics (less than 1.5W)
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
Cisco ASR 9910, V2 fan tray, high -5 to 50C

power optics (greater than 1.5W)
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 45C (SFP+) -5 to 50C

0 to 1800 m
0 to 1800 m
Cisco ASR 9006 with baffle, V2

fan tray
-5 to 40C
0 to 3000 m
-5 to 40C
0 to 3000 m
-5 to 50C
0 to 1800 m
-5 to 45C (SFP+) -5 to 50C

0 to 1800 m
0 to 1800 m
Cisco ASR 9904 with baffle, V1

fan tray
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
-5 to 50C
0 to 1800 m
Fan Tray Operation

The fan trays maintain acceptable operating temperatures for the internal components by drawing
cooling air through a replaceable air filter into the switch fabric and alarm card cage and then through
the line card and RSP card cage.
See Figure 1-12 for the Cisco ASR 9010 Router cooling path, Figure 1-13 for the
Cisco ASR 9006 Router cooling path, and Figure 1-14 for the Cisco ASR 9904 Router cooling path.
In the Cisco ASR 9922 Router, the fan trays draw cooling air from the front of the chassis into the
middle card cage and then through each of the two line card cages top and bottom (Figure 1-15).
The fan tray receives power from the chassis backplane through a wiring harness.
In the Cisco ASR 9912 Router, the rear-insertion fan trays draw cooling air from the front of the
chassis into the card cage and then up through the chassis to exit out the rear (Figure 1-16).
The fan tray contains 12 fans (Cisco ASR 9010 Router, Cisco ASR 9904 Router,
Cisco ASR 9922 Router, and Cisco ASR 9912 Router) or six fans (Cisco ASR 9006 Router), a
controller card, and one front panel status LED indicator:
GreenFan tray is functioning properly.
RedThere is a fault detected in the fan tray.
If the air temperature inside the chassis rises, blower speed increases to provide additional cooling air to
the internal components. If the internal air temperature continues to rise beyond the specified threshold,
the system environmental monitor shuts down all internal power to prevent equipment damage because
of excessive heat.
If the system detects that one or more of the fans in the fan tray has failed, it displays a warning message
on the system console. In addition, the remaining fans go to full speed to compensate for the loss of the
failed fan.
4-33
Chapter 4
Note
Due to air leakage, the chassis should not be operated with any of the fan trays completely missing.
Replace any missing fan tray within five minutes. Any fan tray replacement should be performed when
the chassis is back to room temperature.
Power Module Fans

Each AC or DC power module is equipped with two fans that draw cooling air in through the front of the
power module and force warm air out the back of the power tray:
If the power source is within the required range, the power supply fan remains on.
If a fan fails:
Power module detects an internal overtemperature condition.
Fault and Temp indicators light.
Power module sends an overtemperature warning to the system and then shuts down the system.
For additional power supply troubleshooting information, see Troubleshooting the Power Subsystem,
page 4-7.
Note
For the RSP/RP to communicate properly to a power module in a power tray, input power to at least one
of the three power modules in the power tray should be present.
Overtemperature Conditions
The following console error message indicates that the system has detected an overtemperature condition
or out-of-tolerance power value inside the system:
Queued messages:
%ENVM-1-SHUTDOWN: Environmental Monitor initiated shutdown
The preceding message could also indicate a faulty component or temperature sensor. Enter the show
environment command or the show environment all command at the user EXEC prompt to display
information about the internal system environment. The information generated by these commands
includes:
Voltage measurements on each card from the DC-to-DC converter
The +5 VDC for the I2C module
Operating voltage for the fan trays
Temperature measurements received by two sensors on each card (one for inlet air temperature and
one for the cards hot-spot temperature) as well as temperature measurements from sensors located
in each power module
If an environmental shutdown results from an overtemperature or out-of-tolerance condition, the Fault

indicator on the power supply lights before the system shuts down.
Although an overtemperature condition is unlikely at initial system startup, make sure that:
Heated exhaust air from other equipment in the immediate environment is not entering the chassis
card cage vents.
4-34
Chapter 4

You allow sufficient air flow by maintaining a minimum of 6 inches (15.24 cm) of clearance at both
the inlet and exhaust openings on the chassis and the power modules to allow cool air to enter freely
and hot air to be expelled from the chassis.
Isolating Cooling Subsystem Problems

Follow these steps to isolate a problem with the chassis cooling system if you have an overtemperature
condition:
Step 1
Caution
Step 2
Make sure the fan trays are operating properly when you power on the system. To determine if a fan tray
is operating, check the LED indicator on each fan tray front panel:
OK (green)Fan tray is functioning properly and receiving 48 VDC power, indicating that the
cables from the chassis backplane to the fan tray are good.
Fail (red)Fault is detected in the fan tray. Replace the fan tray.
If neither indicator is on and the blower is not operating, there may be a problem with either the fan
tray or the 48 VDC power supplied to the fan tray. Go to Step 2.
Never unplug all the fan trays at the same time.

Eject and reseat the fan tray making sure the captive screws are securely tightened to a torque of
10 +/1 in-lb.
If the fan tray still does not function, go to Step 3.
Step 3
Check for 48 VDC power by looking at the LED indicators on each power module:
If the Pwr OK indicator is on and the Fault indicator is off on each power module, it indicates that
the fan trays are receiving 48 VDC:
If a fan tray is still not functioning, there could be a problem with the fan tray controller card
or an undetected problem in the fan tray cable. Replace the fan tray.
If the new fan tray does not function, contact a Cisco customer service representative for
assistance.
If the Fault indicator is on, the power supply is faulty. Replace the power supply.
If the Temp and Fault indicators are on, an overtemperature condition exists:
Verify that the power supply fan is operating properly.
If the fan is not operating, replace the power supply.
Contact your Cisco representative if replacing the power supply does not fix the problem.
4-35
Chapter 4
4-36
CH A P T E R
Replacing Cisco ASR 9000 Series Router

Components
The router is equipped as ordered and is ready for installation and startup when it is shipped. As network
requirements change, you may need to upgrade the system by adding or changing components. This
chapter describes how to maintain router components.
Prerequisites and Preparation, page 5-1
Replacing the Chassis Air Filter, page 5-4
Removing and Replacing the Fan Trays, page 5-11
Removing and Replacing Power System Components, page 5-12
Removing and Replacing Cards from the Chassis, page 5-25
Removing a Chassis from the Equipment Rack, page 5-27
Installing a Replacement Chassis in the Equipment Rack, page 5-28
Prerequisites and Preparation

Before you perform any of the procedures in this chapter, be sure that you:
Review the Safety Guidelines, page 1-1.
Read the safety and ESD-prevention guidelines described in Compliance and Safety Information,
page 1-2.
Ensure that you have all the necessary tools and equipment before beginning the procedure.
Have access to the safety and compliance document during the installation, see:
Regulatory Compliance and Safety Information for the Cisco ASR 9000 Aggregation Services Router
5-1
Chapter 5
Field Replaceable Units

In the Cisco ASR 9010 Router, Cisco ASR 9006 Router, and Cisco ASR 9904 Router the following
components are field replaceable units (FRU):
Note
All line cards
RSP cards
Power modules
Fan trays
Air filters
Line card and RSP blank fillers
Compact flash disk
Gigabit Ethernet small form-factor pluggable (SFP) transceiver modules
10-Gigabit Ethernet small form-factor pluggable (SFP+) transceiver modules
10-Gigabit Ethernet small form-factor pluggable (XFP) transceiver modules
Optional card cage doors (Cisco ASR 9010 Router only)
The backplane is not field-replaceable.

In the Cisco ASR 9922 Router and Cisco ASR 9912 Router, the following components are FRUs:
Note
All line cards
RP cards
Fabric cards
Power modules
Fan trays and covers
Air filters and foam media
Blank line card fillers
Gigabit Ethernet small form-factor pluggable (SFP) transceiver modules
10-Gigabit Ethernet small form-factor pluggable (SFP+) transceiver modules
100-Gigabit Ethernet small form-factor pluggable (CFP) transceiver modules
Optional card cage doors
The backplane and BPID cards are not FRUs but are field serviceable.
Online Insertion and Removal

Most Cisco ASR 9000 Series Routers FRUs can be removed and replaced with the power on and the
system operating. This is known as online insertion and removal (OIR). Power modules, fan trays, Route
Switch Processor (RSP) cards, Route Processor (RP) cards, Fabric Controller (FC) cards, Line Cards
5-2
Chapter 5

(LCs), shared port adapter (SPA), and SPA interface processor (SIP) cards all support OIR. Unless
otherwise noted, the maintenance tasks described in this chapter can be performed while the router
remains powered on.
Caution
Note
Although the power trays are not a true FRU because they do not support OIR, a procedure for replacing
the power trays in Cisco ASR 9000 Series Routers is included in this chapter if a replacement becomes
necessary.
OIR Monitoring
The BPID board monitors OIR by counting the number of card insertions for each slot and saving that
information in non-volatile memory. OIR monitoring is done for all fan trays, RSP cards, RP cards, FCs,
and LCs. A card insertion is determined by the CAN Bus Controller (CBC) of the inserted card booting
up and sending a CBC message which is intercepted by the BPID board. Note that a CBC reset or power
cycle on a card will also be interpreted as a card insertion.
Note
A card with an OIR count that exceeds 175 will generate a minor alarm against that slot. If the card OIR
count exceeds 200, a major alarm is generated against that slot. Fan tray insertion counts are not checked
against a threshold. See the Release Notes for Cisco ASR 9000 Series Aggregation Services Routers for
Cisco IOS XR Software Release 3.9.1 for information about CLI commands for obtaining and resetting
card insertion data.
5-3
Chapter 5
Powering Off the Router

Caution
Do not turn off the switch on the power tray to remove individual power modules. Power modules
support OIR, so they can be removed and replaced with the power on and the system operating.
If it becomes necessary to turn all power off to the router, follow these steps:
Step 1
Set the power switch on each power tray to the off (0) position.
Step 2
Power off all circuit breakers for the source power lines connected to the power trays.
Step 3
Verify that the Pwr OK indicator on each power module is off.
Step 4
Verify that the OK indicator on the fan tray is off.

The Cisco ASR 9000 Series Routers are equipped with user-replaceable air filters that help prevent dust
from being drawn into the router. One time per month (or more often in dusty environments), examine
the air filters for damage and cleanliness.
Note
In the Cisco ASR 9010 Router, Cisco ASR 9006 Router, and Cisco ASR 9904 Router, the chassis air
filter is not serviceable. We recommend that you replace the filter at regular maintenance intervals. The
interval may vary between 3 and 12 months depending on the environment.
Note
In the Cisco ASR 9922 Router and Cisco ASR 9912 Router, the three air filters (left, center, and right)
contain foam media which filters the air going into the chassis. The three air filters can be removed from
the chassis so that the foam media (Cisco PIDs 9922-CEN-FLTRMED= and 9922-LR-FLTRMED=) can
be replaced on a regular maintenance interval. The interval may vary between 3 and 12 months
depending on the environment.
Caution
Damage to the air filter can restrict the airflow, cause overheating in the router, and degrade
electromagnetic interference (EMI) compliance. Be careful when cleaning and replacing the filter.
Table 5-1 describes the air filter locations for the Cisco ASR 9000 Series Routers.
5-4

Table 5-1
Air Filter Locations for the Cisco ASR 9000 Series Routers
Router
Air Filter Location
Located underneath the fan trays (Figure 5-1).
Located along the right side of the chassis and is accessible from the rear
(Figure 5-2).
Single air filter located along the right side of the chassis and is accessible
from the rear (Figure 5-3).
Three air filters located on the front of the middle card cage (Figure 5-4).
Three air filters on the front of the RP and FC card cage (Figure 5-6).
Follow these steps to replace an air filter:

Step 1
If the accessory grill has been installed on the front of the Cisco ASR 9010 Router, remove it from the
front of the chassis by simply pulling on the grill until it comes loose. See the Installing Base Chassis
Accessories on the Cisco ASR 9010 Router, page 2-61, and Figure 2-56 for information about the
accessory grill.
Step 2
For the Cisco ASR 9010 Router, remove the air filter by simply sliding it out of the chassis (Figure 5-1).
Figure 5-1
Replacing the Cisco ASR 9010 Router Chassis Air Filter
243206
Chapter 5
Step 3
For the Cisco ASR 9006 Router and Cisco ASR 9904 Router loosen the thumb screw that secures the
filter to the chassis, and then slide the air filter out of the chassis (Figure 5-2).
5-5
Chapter 5
243375
Figure 5-2
1
2
Air filter
Figure 5-3
Thumb screw
351304
1
2
1
Step 4
Air filter
If any fan tray covers have been installed on the front of the chassis, remove them by simply pulling on
the covers until they come loose.
5-6
Thumb screw

Step 5
Note
For the Cisco ASR 9922 Router and Cisco ASR 9912 Router, remove the three air filters by pulling
them off the front of the chassis (Figure 5-4 and Figure 5-6). Then, for each filter, loosen the thumb
screws, rotate the inner frame out, and replace the foam media (Figure 5-7 and Figure 5-8).
In the Cisco ASR 9922 Router (version 2 air filter) the center air filter, shown in Figure 5-5, does not
does not contain replaceable foam media. The left and right air filters are the same as version 1 and
contain replaceable foam media.
Figure 5-4
Cisco ASR 9922 Router Chassis Air Filters
344069
Chapter 5
5-7
Chapter 5
Cisco ASR 9922 Router Chassis Center Air FilterVersion 2
362043
Figure 5-5
5-8

Figure 5-6
Cisco ASR 9912 Router Chassis Air Filter
Figure 5-7
Removing the Cisco ASR 9922 Router Chassis Center Air FilterVersion 1
303666
1
3
302420
Chapter 5
Loosen thumb screws
Rotate and lower inner frame
Remove foam filter media
5-9
Chapter 5
Figure 5-8
Removing the Cisco ASR 9922 Router Chassis Side Air Filter Versions 1 and 2
302421
Loosen thumb screws
Rotate and lower inner frame
Step 6
Visually check the condition of the air filter and/or its foam media to determine whether to install a new
replacement filter or foam media.
Step 7
Install the new air filter.
Note
Caution
For the Cisco ASR 9010 Router, slide the new air filter into the air filter door (honeycomb side up).
For the Cisco ASR 9006 Router and Cisco ASR 9904 Router, tighten the thumb screw to secure the
filter to the chassis.
For the Cisco ASR 9922 Router (version 1 air filter) and Cisco ASR 9912 Router, tighten the thumb
screws that attach the inner frame to the air filter and re-attach the three air filters to the front of the
chassis. For the Cisco ASR 9922 Router (version 2 air filter) tighten the thumb screws that attach
the inner frame to the left and right air filters only. Attach the new center air filter, with arrows
pointing upwards, and re-attach both side filters to the front of the chassis.
For the version 2 air filter on the Cisco ASR 9922 Router, the center does not have thumb screws because
it does not have replaceable foam media.
Align and seat the door carefully to avoid damaging the EMI-preventive gaskets on the door. The air
filter door must be closed and secured at all times to maintain correct EMI performance.
5-10
Remove foam filter media
Chapter 5

Removing and Replacing the Fan Trays
Removing and Replacing the Fan Trays

Prerequisites
For the Cisco ASR 9010 Router, remove the accessory grill before removing and replacing the fan trays.
For the Cisco ASR 9922 Router and Cisco ASR 9912 Router, remove the fan tray cover before removing
the fan trays for replacement.
6-inch long number 2 Phillips screwdriver (torque 10 in-lb)
Steps
Follow these steps to remove and replace the fan trays:
Caution
Caution
Be sure that the fans have stopped running before removing the fan tray. The fans can take from 3 to 5
seconds to completely stop running after disengaging the fan tray latch. Handling the fan tray before the
fans have stopped running could cause fingertip injury.
Note
Due to air leakage, the chassis should not be operated with any of the fan trays completely missing.
Replace any missing fan tray within five minutes. Any fan tray replacement should be performed when
the chassis is back to room temperature.
Note
If the accessory grill has been installed on the front of the Cisco ASR 9010 Router, you must remove it
before you can remove the lower fan tray. You can remove the accessory grill by simply pulling on the
grill until it comes loose. See Installing Base Chassis Accessories on the Cisco ASR 9010 Router,
page 2-61, and Figure 2-56 for information about the accessory grill.
Note
If the fan tray cover has been installed on the front of the Cisco ASR 9922 Router or
Cisco ASR 9912 Router, you must remove it before you can remove the fan tray. Remove the fan tray
cover by simply pulling on the cover until it comes loose.
To remove a fan tray from the chassis (see Figure 2-14, Figure 2-15, Figure 2-16, or Figure 2-17):
Step 1
Use the 6-inch long number 2 Phillips screwdriver to a torque of 10 +/1 in-lb to loosen the captive
screw(s) that secure the fan tray.
Step 2
Use the handle on the fan tray front panel to pull the fan tray halfway out of the module bay.
Step 3
5-11
Chapter 5
Removing and Replacing Power System Components
Caution
Use two hands when handling the fan tray. Each Cisco ASR 9010 Router version 1 fan tray weighs about
16 pounds (7.27 kg). Each Cisco ASR 9922 Router fan tray or Cisco ASR 9010 Router version 2 fan
tray weighs about 18 pounds (8.18 kg).
To install a fan tray into the chassis:

Step 1
Lift the fan tray (with two hands) and slide it halfway into the module bay.
Step 2
Slowly push the fan tray into the chassis until it mates with the backplane connector at the back of the
module bay.
Caution
To prevent damage to the connectors, do not use excessive force when inserting the fan tray into the
chassis.
Step 3
Tighten the captive screw(s) on the fan tray using the 6-inch long number 2 Phillips screwdriver to a
torque of 10 +/1 in-lb to secure it to the chassis.
Step 4
Verify that the (green) OK status indicator on the front of the fan tray goes on. If the OK indicator does
not light, see Troubleshooting the Cooling Subsystem, page 4-32.

The Cisco ASR 9000 Series Routers support OIR of power modules. If you are replacing a redundant
power module, you can remove and install the power module while the system remains powered on
without causing an electrical hazard or damage to the system. This feature enables you to replace a power
module while the system maintains all routing information and ensures session preservation.
However, to maintain operational redundancy and proper cooling, and to meet EMI compliance
standards, you must have at least one working power module installed (more than one for a fully
configured system). When you remove a failed power module with the router in operation, perform the
replacement as quickly as possible. Make sure you have the replacement power module ready before
beginning the removal and installation procedure.
Note
For the RSP/RP to communicate properly to a power module in a power tray, input power to at least one
of the power modules in the power tray should be present.
This section contains procedures on how to remove and install AC and DC power modules used in the
Cisco ASR 9000 Series Routers.
Changing Between Version 1, Version 2, Version 3, AC, and DC Power Modules, page 5-13
Removing a Version 1 AC or DC Power Module, page 5-14
Removing a Version 2 or Version 3 AC or DC Power Module, page 5-15
Installing a Version 1 AC or DC Power Module, page 5-16
Installing a Version 2 or Version 3 AC or DC Power Module, page 5-16
5-12
Chapter 5

Caution
Do not turn off the switch on the power tray to remove individual power modules. Power modules
support OIR, so they can be removed and replaced with the power on and the system operating.
Changing Between Version 1, Version 2, Version 3, AC, and DC Power Modules

Follow these steps when changing between version 1, version 2, version 3, AC, and DC power modules:
Step 1
Before making any physical changes, check the software configuration to ensure no ROMMON variable
CHASSIS_TYPE (such as CHASSIS_TYPE=10_SLOT) is set to override the chassis type.
Step 2
At the Cisco IOS-XR command prompt on the RSP console, run the pwrmod_change command. This
command displays the current power module and system information.
RP/0/RSP0/CPU0:RO9_P2RSP3# run
Wed Jul 4 20:18:58.034 UTC
# pwrmod_change
Current system:
power supply type : AC power supply version 2
chassis type : 10-slot
chassis bpid: 0x2fa, PID: ASR-9010-AC
UDI name: ASR-9010 AC, UDI desc: ASR-9010 AC
Step 3
Enter your new power module type.

Please enter the number that corresponds to the power supply type that is being migrated
to. Do not enter the current power system information, use the future power system type.
1)
AC power supply version 1, fits 3 across in power shelf ASR-9010-AC
2)
DC power supply version 1, fits 3 across in power shelf ASR-9010-AC
3)
AC power supply version 2, fits 4 across in power shelf ASR-9010-AC
4)
DC power supply version 2, fits 4 across in power shelf ASR-9010-AC
ATTENTION: You are about to commit a change in the power system type for the chassis.
Please confirm that the OLD and NEW power system information listed here is correct. Once
the system software change is committed, you must physically remove the OLD power system
and replace it with the NEW power system of the type specified below here. Any mismatch
between the programmed system value and the actual physical installation may cause boot
and power management issues in the system.
OLD POWER SYSTEM:
power supply type: AC power supply version 2
chassis type: 10-slot
chassis bpid: 0x2fa, PID: ASR-9010-AC
UDI name: ASR-9010 AC, UDI desc: ASR-9010 AC
NEW POWER SYSTEM:
power supply type: DC power supply version 2
chassis type: 10-slot
chassis bpid: 0x2fa, PID: ASR-9010-DC
UDI name: ASR-9010 DC, UDI desc: ASR-9010 DC
5-13
Chapter 5
Step 4
Confirm your choice.

Please confirm that you wish to upgrade from AC power supply version 2 power system to DC
power supply version 2 power system by typing "yes" at the prompt below. Any other
response will cancel the power system change operation [yes/cancel]?
yes
Step 5
After the success message appears, power down the chassis.

start update CBC eeprom, offset = 0x0,length=1000
..............................................................
done update CBC eeprom
start update I2C eeprom
...............................................................
done update I2C eeprom
The power system programming change is complete. The system must now be completely powered
down, and the NEW power system hardware installed. When the system is rebooted the
software will recognize the new power system. Please power down the system at this point.
#
Step 6
Remove the old power module (see Removing a Version 1 AC or DC Power Module, page 5-14 or
Removing a Version 2 or Version 3 AC or DC Power Module, page 5-15).
Caution
Use two hands to remove the power module. The power supply weighs about 6.5 pounds (2.95 kg).
Step 7
Caution
Install the new power module (see Installing a Version 1 AC or DC Power Module, page 5-16 or
Installing a Version 2 or Version 3 AC or DC Power Module, page 5-16).
Step 8
Power up the chassis.
Step 9
Verify that the (green) Power Input indicator on the front of the power module goes on. If the indicator
does not light, see Troubleshooting the Power Subsystem, page 4-7.
Removing a Version 1 AC or DC Power Module

Follow these steps to remove a version 1 AC or DC power module from the power tray (Figure 5-9).
Step 1
Push the door latch to the left to release the door.
Step 2
Pivot the door to the right to eject the power module from its bay.
Step 3
Slide the power module out of its bay while supporting it with your other hand.
Caution
Use two hands to remove the power module. The power supply weighs about 6.5 pounds (2.95 kg).
5-14
Chapter 5

Removing or Installing a Version 1 AC or DC Power Module
243181
Figure 5-9
Removing a Version 2 or Version 3 AC or DC Power Module

Follow these steps to remove a version 2 or version 3 AC or DC power module from the chassis (see
Figure 5-10). The Cisco ASR 9904 Router chassis only has one power tray as shown in Figure 5-11.
Note
Unscrew the screw that secures the power module using a 7/16 hex socket and torque wrench with the
torque set to 50 in-lb.
Step 4
Pull the handle down.
Step 5
Slide the power module out of its bay while supporting it with your other hand.
Removing or Installing a Version 2 or Version 3 AC or DC Power Module
331400
Figure 5-10
5-15
Chapter 5
Removing or Installing a Version 2 AC or DC Power Module from the Cisco ASR 9904
Router
351307
Figure 5-11
Installing a Version 1 AC or DC Power Module

Follow these steps to install a new version 1 AC or DC power module (Figure 5-9):
Step 1
Slide the power module into the bay until it mates with its backplane connector.
Step 2
Pivot the door to the left until the door latch locks.
Caution
Step 3
Installing a Version 2 or Version 3 AC or DC Power Module

Follow these steps to install a new version 2 or version 3 AC or DC power module (Figure 5-10):
Step 1
Slide the power module into the bay until it mates with its backplane connector.
Step 2
Move the handle up.
Step 3
Tighten the screw that secures the power module using a 7/16 hex socket and torque wrench with the
torque set to 50 in-lb.
Caution
5-16
Chapter 5

Step 4
Disconnecting AC Power
Follow these steps to disconnect an individual AC power cord:
Step 1
Power OFF (0) the circuit breaker assigned to the AC power source you are disconnecting.
Step 2
Loosen the retainer bracket holding the AC power cord to the power tray receptacle.
Step 3
Unplug the AC power cord from the power tray receptacle.
Caution
Do not turn off the switch on the power tray to remove AC power cords. An individual AC power cord
can be unplugged while the system is powered from other AC power sources.
If it becomes necessary to disconnect all AC power from the router, follow these steps:
Caution
Do not disconnect all power from the router to replace components, including power modules. See
Removing and Replacing Power System Components, page 5-12.
Step 1
Set the power switch at the rear of the Version 1 AC power tray to the OFF (0) position. For Version 2
and Version 3 AC power trays, set the power switch at the front of the to the OFF (0) position.
Step 2
Power OFF (0) the circuit breakers assigned to the AC power sources you are disconnecting.
Caution
breaker switch in the OFF (0) position until you are ready to turn it on.
Step 3
Loosen the retainer bracket holding the AC power cords to the power tray receptacle.
Step 4
Unplug the AC power cords from the power tray receptacles.
Reconnecting AC Power
Follow these steps to reconnect an individual AC power cord to a power tray:
Step 1
Power OFF (0) the circuit breaker assigned to the AC power source you are reconnecting.
Step 2
Plug the AC power cord into the power tray receptacle.
Step 3
Close and tighten the retainer bracket holding the AC power cord to the power tray receptacle.
Step 4
Power on the AC power source circuit breaker.
5-17
Chapter 5
Caution
Do not turn off the switch on the power tray to reconnect AC power cords. An individual AC power cord
can be plugged in while the system is powered from other AC power sources.
If power has been totally disconnected from the router, follow these steps to reconnect AC power to the
AC power tray:
Caution
The following procedure is only to be used when reconnecting power to all power trays in a system that
has been powered down completely.
Step 1
Verify that the power switch at the rear of the Version 1 AC power tray is set to the OFF (0) position. For
Version 2 and Version 3 AC power trays, verify that the power switch at the front of the power tray set
to the OFF (0) position.
Step 2
Check that the circuit breaker assigned to the AC power source you are connecting is set to OFF (0).
Caution
Step 3
Plug the AC power cords into the power tray receptacle (Figure 3-19).
Step 4
Close the retainer bracket to secure the AC power cord plug to the power tray receptacle.
Step 5
Power on the AC power source circuit breaker.
Step 6
Set the power switch at the rear of the AC power tray to the ON (1) position.
5-18
Chapter 5

Disconnecting DC Power
Caution
It is not necessary to disconnect all power from the router to replace components, including power
modules. See Removing and Replacing Power System Components, page 5-12.
Follow these steps to disconnect an individual DC power source from a power tray (Figure 3-21 for
version 1 DC power, Figure 3-22 for version 2 DC power, or Figure 3-23 for version 3 DC power):
Step 1
Caution
Step 2
Power off the circuit breaker assigned to the DC power source you are disconnecting.
breaker switch in the STANDBY (0) position until you are ready to turn it on.
Caution
To prevent injury and damage to the equipment, always remove the source DC power cables and ground
from the power tray terminals in the following order: (1) negative (), (2) positive (+), (3) ground.
Step 3
Disconnect the DC power cables from their terminals in the following order and note the color of each
cable (Figure 3-21 for version 1 DC power, Figure 3-22 for version 2 DC power, or Figure 3-23 for
version 3 DC power):
Step 4
a.
Negative (PWR) cables first.
b.
Positive (RTN) cables next.
c.
Ground cable last.
Repeat Step 1 through Step 3 for the other power tray, if installed.
If it becomes necessary to disconnect all DC power from the router, follow these steps (Figure 3-21 for
version 1 DC power, Figure 3-22 for version 2 DC power, or Figure 3-23 for version 3 DC power):
Note
Caution
This procedure describes how to disconnect DC power from all power modules in a single DC power
tray. The procedure is the same for each DC power tray, if more than one is installed.
If only one power tray is installed, performing the following procedure turns off all power to the router.
Step 1
Set the power tray switch to the STANDBY (0) position.
Step 2
Power OFF (0) the circuit breaker assigned to the DC power source you are disconnecting.
Caution
5-19
Chapter 5
Step 3
Caution
To prevent injury and damage to the equipment, always remove the source DC power cables and ground
from the power tray terminals in the following order: (1) negative (), (2) positive (+), (3) ground.
Step 4
Disconnect the DC power cables from their terminals in the following order and note the color of each
cable (Figure 3-21 for version 1 DC power, Figure 3-22 for version 2 DC power, or Figure 3-23 for
version 3 DC power):
Step 5
a.
Negative (PWR) cables first.
b.
c.
Ground cable last.
Repeat Step 1 through Step 4 for the other power tray, if installed.
Reconnecting DC Power
Caution
Use this procedure only when reconnecting power to all power modules in a system that is powered down
completely.
Follow these steps to reconnect DC power to a DC power tray:
Step 1
Set the power switch to the OFF (0) position.
Step 2
Check that the circuit breaker assigned to the DC power source you are reconnecting is powered OFF (0).
Step 3
Reconnect the DC power cables in the following order:

a.
Ground cables first.
b.
c.
Negative (PWR) cable last.
d.
Repeat Step 1 through Step 3 for the other power tray (Cisco ASR 9010 Router only)
Caution
To prevent injury and damage to the equipment, always attach the ground and source DC power cable
lugs to the power tray terminals in the following order: (1) ground to ground, (2) positive (+) to positive
(+), (3) negative () to negative ().
Caution
Do not overtighten the nuts that secure the DC power cables to the power tray terminals. The nuts should
be tightened using the 7/16 hex socket and torque wrench to a torque of 45 to 50 in-lb.
Step 4
Replace the clear plastic safety covers over the DC power connection terminal studs and tighten the
screws.
Step 5
Set the DC power source circuit breaker to ON (1).
5-20
Chapter 5

Step 6
Set the power tray switch to ON (1).
Removing an AC or DC Power Tray from a Cisco ASR 9000 Series Router

The power trays are not a true FRU because they do not support OIR. However, if replacement is
necessary, follow these steps to remove and replace the power trays in a Cisco ASR 9000 Series Router.
Caution
Power tray removal and replacement procedures are to be performed by qualified service persons only.
Caution
All power to the node must be shut off at the branch circuit disconnect device before beginning power
tray replacement procedures. Removal of a tray requires disconnection of power cabling on the back of
the chassis that exposes service persons to exposed wiring from the unaffected tray.
Caution
All terminal block covers should be replaced prior to energizing the power cabling to the system.
Follow these steps to remove an AC or DC power tray from the chassis:
Step 1
Disconnect AC or DC power from the power tray rear panel.
Step 2
Remove all power modules from the power tray.
Step 3
For the Cisco ASR 9010 Router, remove the front grill by pulling it away from the chassis (Figure 5-12).
Removing the Front Grill on the Cisco ASR 9010 Router
247895
Figure 5-12
Step 4
For the Cisco ASR 9922 Router, the front power tray bezel is a standard item that comes with ball studs
already installed. Simply install it by snapping it onto the chassis, or remove it by pulling it away from
the chassis (Figure 5-13).
5-21
Chapter 5
Removing the Front Power Tray Bezel on the Cisco ASR 9922 Router
302359
Figure 5-13
Step 5
For the Cisco ASR 9912 Router, the vented power tray bezel is a base chassis accessory that snaps onto
the front of the power system. comes with ball studs already installed. Remove it by pulling it away from
the chassis (Figure 2-85).
Step 6
Loosen and remove the four screws (two screws at each end) that attach the power tray to the chassis.
Step 7
Loosen the two captive screws (one per ejector lever) to release the ejector levers. Figure 5-14 shows the
process for the version 1 power trays, and Figure 5-15 shows the process for the version 2 power trays.
The process for version 3 power trays is similar to the process for version 2 power trays, as shown in
Figure 5-15.
Figure 5-14
Removing a Power TrayVersion 1 Power Tray (Cisco ASR 9010 Router Shown)
247898
5-22
Chapter 5

Figure 5-15
Removing a Power Tray Version 2 Power Tray (Cisco ASR 9010 Router Shown)
284407
Remove screws on each

side that secure the power
tray to the chassis
Loosen the captive screw in

each ejector lever
Rotate the ejector levers out

to unseat the tray from its
mating connector
Step 8
Rotate the ejector levers away from the tray to unseat the tray from its mating connector. Figure 5-14
shows the process for the version 1 power trays, and Figure 5-15 shows the process for the version 2 and
version 3 power trays.
Step 9
Slide the power tray out of the bay of the chassis.
Installing an AC or DC Power Tray into a Cisco ASR 9000 Series Router

Follow these steps to install an AC or DC power tray into the chassis:
Step 1
Slide the power tray into the bay until it engages its mating connector on the chassis. The ejector levers
will partly rotate inward as you do this.
Step 2
Fully rotate the ejector levers inward to fully seat the power tray into its mating connector and seat the
power tray mounting ears against the chassis mounting ears. Figure 5-16 shows how to install the version
1 power trays and Figure 5-17 shows how to install the version 2 power trays. The installation of version
3 power trays is similar to the installation of version 2 power trays, as shown in Figure 5-17.When the
power tray is fully seated, the captive screw in each ejector aligns with the screw hole in the power tray
frame.
5-23
Chapter 5
Figure 5-16
Rotating the Ejector Levers Inward to Seat the Version 1 Power Tray
3
248319
1
2
Screw hole in the power

tray frame for ejector lever
captive screw
Ejector lever captive screw
Power tray mounting ear
Rotating the Ejector Levers Inward to Seat the Version 2 Power Tray
331403
Figure 5-17
5-24
Chapter 5

Step 3
Install the captive screw in each ejector lever into the screw hole in the power tray frame (Figure 5-16
or Figure 5-17).
Step 4
Use the 6-inch long number 2 Phillips screwdriver to tighten the two ejector screws to a torque of 10 +/-1
in-lb to secure the ejectors and to secure the tray to its mating connector.
Step 5
Install and tighten two screws through the power tray mounting ears on each side into the screw holes in
the chassis mounting ears to secure the tray to the chassis.

This section describes the procedures for removing and installing an RSP card, RP card, FC, or LC.
See the Cisco ASR 9000 Series Aggregation Services Router SIP and SPA Hardware Installation Guide
for information about removing and installing SIP and SPA cards.
For a information about the router components and slot numbering for the Cisco ASR 9010 Router,
Cisco ASR 9006 Router, and Cisco ASR 9904 Router, see Removing RSP Cards and Line Cards
from the Cisco ASR 9010 Router, Cisco ASR 9006 Router, and Cisco ASR 9904 Router, page 2-23.
For a information about the router components and slot numbering for the Cisco ASR 9922 Router
and Cisco ASR 9912 Router, see Removing RP Cards, Fabric Cards, and Line Cards from the Cisco
ASR 9922 Router and Cisco ASR 9912 Router, page 2-31.
Caution
Caution
Be careful to avoid damaging the EMI gasket that runs along the full height of the card front panel edges.
Damage to the EMI gasket can affect the ability of your system to meet EMI requirements.
Caution
To avoid damaging card mechanical components, never carry an RSP card, RP card, FC, or LC by the
captive installation screws or ejector levers. Doing so can damage these components and cause card
insertion problems.
Note
The BPID board monitors OIR by counting the number of card insertions for each slot and saving that
information in non-volatile memory. OIR monitoring is done for all line cards, the RSP, the RP, and the
fan trays. See OIR Monitoring, page 5-3 for more information.
5-25
Chapter 5
Removing Cards from the Chassis

Follow these steps to remove and replace an RSP card, RP card, FC, or LC from the card cage:
Step 1
Step 2
Step 3
Disconnect any cables from the card.

a.
Identify the type of line card and its slot number. Write this information down before you disconnect
the cables. Youll need this information when you reinstall the line cards.
b.
Identify the line card cable and its port connection. Label the cable with this information.
c.
Starting with the port of the line card farthest from the cable management bracket, disconnect the
interface cable connectors from each of the line card ports.
d.
Carefully remove the cables from the cable-management bracket attached to the front panel of the
line card.
e.
(Optional) Use the 6-inch long number 2 Phillips screwdriver to a torque of 10 +/1 in-lb to loosen
the captive screw that secures the cable-management bracket to the line card and remove the
cable-management bracket from the line card.
f.
Carefully remove the cables from the horizontal cable management tray at the top of the chassis or
side cable management brackets (Cisco ASR 9006 Router) and carefully place the cable bundle out
of the way.
Remove the card (Figure 2-24, Figure 2-25, Figure 2-35, or Figure 2-36):
a.
Use the 6-inch long number 2 Phillips screwdriver to loosen the captive screws at each end of the
card front panel.
b.
On the FC and LC push in both ejector lever release buttons.
c.
d.
container.
Repeat Step 1 and Step 2 for each card.
Replacing Cards in the Chassis

Follow these steps to replace a previously removed RSP card, RP card, FC, or LC from the card cage:
Step 1
Step 2
Install the card (Figure 2-24, Figure 2-25, Figure 2-35, or Figure 2-36):
a.
Slide the card into the slot, being sure to install the card in the same slot you recorded when you
removed the card.
b.
Use the 6-inch long number 2 Phillips screwdriver to a torque of 10 +/1 in-lb to tighten the captive
screws at each end of the card front panel.
c.
Pivot the ejector levers to seat the card into the backplane connector.
Reconnect cables to the card:

a.
If you previously disconnected the card cable management bracket, reattach it to the card and use
the 6-inch long number 2 Phillips screwdriver to a torque of 10 +/1 in-lb to tighten the captive
screw on the bracket to secure it to the card front panel.
5-26
Chapter 5

Step 3
b.
Carefully reroute the cables through the horizontal cable management tray at the top of the chassis
(the Cisco ASR 9922 Router has an additional tray at the bottom of the chassis) or side cable
management brackets (Cisco ASR 9006 Router and Cisco ASR 9904 Router).
c.
Carefully reroute cables through the card cable-management bracket.
d.
Starting with the port of the card closest to the cable management bracket, reconnect the interface
cable connectors to each of the card ports using the cable and port connection information you
recorded when removing the cables.
Repeat Step 1 and Step 2 for each card.

Follow these steps to remove the chassis and its components from the equipment rack:
Caution
You must use two people to remove the chassis from the equipment rack safely. An empty chassis can
weigh up to approximately 300 pounds (136 kg).
Step 1
Power off the router (see Powering Off the Router, page 5-4).
Step 2
Power off the circuit breakers to the power supplies.
Step 3
Disconnect the power from the power modules on the rear of the chassis:
For AC power modules, see Disconnecting AC Power, page 5-17.
For DC power modules, see Disconnecting DC Power, page 5-19.
Step 4
Disconnect the supplemental bonding and grounding connection from the chassis (see Supplemental
Bonding and Grounding Connections, page 2-56).
Step 5
Remove the fan tray (see Removing and Replacing the Fan Trays, page 5-11).
Step 6
Disconnect RSP/RP cables connected to the console port, auxiliary port, or either of the management
Ethernet ports. Be sure to label each of the RSP/RP cables before you disconnect the cables.
Step 7
Disconnect any cables connected to the external alarm port on the alarm display.
Label each of the alarm display cables before you disconnect the cables.
Step 8
Disconnect the line card interface cables.
Step 9
Remove the RSP cards, RP cards, FCs, and LCs from the chassis (see Removing and Replacing Cards
from the Chassis, page 5-25).
Step 10
Remove the chassis air filter (see Replacing the Chassis Air Filter, page 5-4).
Step 11
Remove the chassis from the rack.

a.
Using the side handles to support the weight of the chassis, remove the screws that attach the chassis
rack mount flanges and the side rack mount brackets to the rack posts.
b.
Carefully lift the chassis out of the rack and set it aside.
c.
Use the rear handle on the Cisco ASR 9922 Router to push the chassis out of the rack and onto an
adjacent pallet jack for transport.
5-27
Chapter 5

Follow these steps to install the replacement chassis and components in the equipment rack:
Step 1
Install the new chassis in the rack (see Rack-Mounting the Router Chassis, page 2-42).
Step 2
Install the power modules (see Removing and Replacing Power System Components, page 5-12).
Step 3
Install the fan tray (see Removing and Replacing the Fan Trays, page 5-11).
Step 4
Install the RSP cards, RP cards, FCs, and LCs. (see Removing and Replacing Cards from the Chassis,
page 5-25).
Step 5
Install the chassis air filter (see Replacing the Chassis Air Filter, page 5-4).
Step 6
Connect all line card and interface cables (see Connecting Line Card Network Interface Cables,
page 3-17).
Step 7
Connect the supplemental bonding and grounding connection (if there is one) to the chassis (see
Supplemental Bonding and Grounding Connections, page 2-56).
Step 8
Connect power to the power trays on the rear of the chassis.
Step 9
For AC power modules, see Reconnecting AC Power, page 5-17.
For DC power modules, see Reconnecting DC Power, page 5-20.
To turn on power to the router, see Powering On the Router, page 3-32.
Packing a Chassis for Shipment

Use the packaging that came with the replacement chassis to repack and ship the chassis being replaced.
Before shipping the chassis being replaced, pack the chassis back into the shipping rack (see Unpacking
the Router, page 2-3).
5-28
A P P E N D I X
This appendix lists specifications for the Cisco ASR 9000 Series Aggregation Services Routers.
Cisco ASR 9000 Series Routers Environmental Specifications
Power System DC Output Levels
RSP/RP Port Specifications
A-1
Appendix A

Table A-1
Chassis
Height
Router
36.75 inches
(93.35 cm)
Chassis Width
Chassis Depth
Chassis Weight
17.50 inches (44.45 cm)

19.0 inches (48.3 cm)
including chassis
rack-mount flanges and
front door width
28.65 inches (72.72 cm) Chassis only1

including cable
Chassis: fully configured
management system and
using all card slots and six
front cover
power modules
149.5 pounds (67.81 kg)
375 pounds (170.5 kg)
17.50 inches
(44.45 cm)
17.50 inches (44.45 cm)

19.0 inches (48.3 cm)
including chassis
front door width

including cable
using all card slots and six
front cover
power modules
87.5 pounds (39.69 kg)
230 pounds (104.33 kg)
10.38 inches
(26.36 cm)
17.75 inches (45.08 cm)

19.0 inches (48.3 cm)
including chassis
rack-mount flanges

including cable
management system
using all card slots and four
power modules
43.3 pounds (19.64 kg)
122.8 pounds (55.70 kg)
77.00 inches
(195.58 cm)
17.60 inches (44.70 cm)

19.0 inches (48.3 cm)
including chassis
front door width
26.3 inches (66.82 cm)

30.00 inches (76.20 cm)
including cable
management system
30.62 inches (77.77 cm)
with front doors
Chassis only1
using all card slots and four
power modules
300 pounds (136 kg)
1038 pounds (470.28 kg)
52.5 inches
(133.4 cm)
17.6 inches (44.7 cm)

19.0 inches (48.3 cm)
including chassis
front doors
25.7 inches (65.2 cm)

29.4 inches (74.7 cm)
including cable
management system
Chassis only1
using all card slots and three
power trays
181 pounds (82.10 kg)

30.1 inches (76.4 cm)
including cable
643 pounds (291.66 kg)
front doors
1. Chassis only does not include cards, power modules, fan trays, filter or chassis accessories.
A-2
Appendix A

Table A-2
Description
Value
Operating Temperature:1
41 to 104F
(5 to 40C)
Operating Temperature1,2
(Short term)3,4
23 to 131 F (-5 to 55C) for Cisco ASR 9904 Router

23 to 131 F (5 to 55C) for Cisco ASR 9006 Router
23 to 122 F (5 to 50C) for Cisco ASR 9010 Router Cisco ASR 9922 Router, and
Non-operating Temperature
-40 to 158F
(-40 to 70C)
Humidity
Operating: 10 to 85 percent noncondensing

Non-operating: 5 to 95 percent noncondensing
Altitude
Power Dissipation
Operating: 0 to 13,000 ft. (0 to 4,000 m)

Non-operating: 0 to 15,000 ft (0 to 4,570 m)
16-port 10-Gigabit Ethernet line card: 0 to 5,904 ft (0 to 1,800 m)
All Cisco ASR 9000 Series Routers
Use the Cisco Power Calculator (Cisco.com account required) at
http://tools.cisco.com/cpc/launch.jsp to estimate the maximum power distribution.
Acoustic noise
78 dB at 80.6F (27C) maximum
Shock
Operating (halfsine): 21 in/sec (0.53 m/sec.)

Non-operating (trapezoidal pulse): 20 G6, 52 in/sec (1.32 m/sec)
Vibration
Operating: 0.35 Grms7 from 3 to 500 Hz

Non-operating: 1.0 Grms from 3 to 500 Hz
1. Operating temperature specifications for the router will differ from those listed in this table when 40-port Gigabit Ethernet line cards using
GLC-GE-100FX SFP transceiver modules are installed in the router. This is due to the lower temperature specifications of the SFP module. Please contact
a Cisco representative for more information.
2. Short term operating temperature specifications for the router will differ from those listed in this table when the 16-port 10-Gigabit Ethernet line card is
installed in the router because of the lower temperature specifications of the SFP+ modules and that are used in this line card. When using this line card,
the maximum operating temperature is 104F (40C).
3. Short-term refers to a period of not more than 96 consecutive hours and a total of no more than 15 days in 1 year. (This refers to a total of 360 hours in
any given year, but no more than 15 occurrences during that 1-year period.).
4. The 24 port 10 Gigabit Ethernet linecard requires high temperature optics to run in the extended temperature range.
5. Operating altitude specifications for the router will differ from those listed in this table when the 16-port 10-Gigabit Ethernet line card is installed in the
router. When using the SFP-10G-SR module, the maximum altitude is 5905 ft. (1800 m). When using the SFP-10G-LR or SFP-10G-ER modules, the
maximum altitude is sea level.
6. G is a value of acceleration, where 1 G equals 32.17 ft./sec2 (9.81 m/sec2).
7. Grms is the root mean square value of acceleration.
A-3
Appendix A

Table A-3
Description
Cisco ASR 9010
Cisco ASR 9006
Cisco ASR 9904
Cisco ASR 9922
Cisco ASR 9912
Power
modules per
system
Version 1 power
system: Up to six AC
power modules per
system, three per tray
Version 1 power
system: Up to three
AC power modules
per system
Version 2 power
system:
Version 2 power
system: Up to sixteen
AC power modules per
system, four per tray
Version 2 power
system: Up to eight
AC power modules
per system, four per
tray
Version 2 power
system: Up to four
AC power modules
per system
Version 2 power
system:
Up to twelve AC
power modules per
system, four per
tray
Up to four AC
power modules
per system
Version 3 power
system: Up to six AC
power modules per
Version 2 power
system: 3290 VA
(3000 W output
module)
Version 3 power
system: 6510 VA
(6000 W output
module)
Total AC
input power
per power
module
Version 1 power
system: 3400 VA
(volt-amps) per AC
power module
Version 2 power
system: 3290 VA
(3000 W output
module)
Version 2 power
system: 3290 VA
(3000 W output
module)
Version 3 power
system: Up to twelve
AC power modules per Version 3 power
system, three per tray system:
Up to nine AC
power modules per
system, three per
tray
Version 2 power
system: 3290 VA
(3000 W output
module)
Version 3 power
system: 6510 VA
(6000 W output
module)
Version 2 power
system: 3290 VA
(3000 W output
module
Version 3 power
system: 6510 VA
(6000 W output
module)
AC power modules
operate in N+N
redundancy mode2
AC power modules
operate in N+N
redundancy mode2
200240 VAC nominal (range: 180 to 264 VAC)

Rated input
220240 VAC (UK)
voltage per
power module
Rated input
line
frequency1
50/60 Hz nominal (range: 47 to 63 Hz)

50/60 Hz (UK)
Input current
draw1
15 A maximum at 200 VAC

13 A maximum at 220 to 240 VRMS (UK)
Source AC
service
requirement1
20 A North America; 16 A international;

13 A United Kingdom
Redundancy
AC power modules
operate in N+N
redundancy mode2
At least two AC
power modules
required for N+1
redundancy for a
fully configured
system
At least two AC
power modules
required for N+1
redundancy for a
fully configured
system
1. For each AC power supply module. Some power/chassis configurations may operate at lower current ratings than those specified in this table. Contact your
Cisco technical representative for more information.
2.
The number of AC power modules needed depends on the configuration of the chassis (e.g. number of line cards, RP cards, and FCs installed). Use the
Cisco Power Calculator (Cisco.com account required) at http://tools.cisco.com/cpc/launch.jsp to calculate how many AC power modules are needed.
A-4
Appendix A
Caution
Be sure that the chassis configuration complies with the required power budgets. Failure to properly
verify the configuration may result in an unpredictable state if one of the power units fails. Contact your
local sales representative for assistance.
A-5
Appendix A

Table A-4
Description
Cisco ASR 9010
Cisco ASR 9006
Cisco ASR 9904
Cisco ASR 9922
Cisco ASR 9912
Power
modules per
system
Version 1 power
system: Up to six DC
power module per
Version 1 power
system: Up to three
DC power modules
per system
Version 2 power
DC power modules per
Version 2 power
system: Up to eight
DC power modules
tray
Version 2 power
system: Up to four
DC power modules
per system
Version 2 power
system: Up to
four DC power
modules per
system
Version 2 power
system: Up to
twelve DC power
modules per
system, four per
tray
Version 2 power
system: 2300 W
(2100 W output
module)
Version 2 power
system: 2340 W
(2100 W output
module)
Version 3 power
system: Up to eight
DC power modules
tray
Total DC
input power
per power
module
Version 1 power
system: 1700 W
(1500 W output
module)
Version 1 power
system: 1700 W
(1500 W output
module)
Version 2 power
system: 2340 W
(2100 W output
module)
Version 2 power
system: 2300 W
(2100 W output
module)
Version 3 power
DC power modules per Version 3 power
system: Up to
twelve DC power
modules per
system, four per
tray
Version 2:
2340 W (2100 W
output module)
Version 3 power
system:
Version 3 power
system: 4730 W (4400 4730 W (4400 W
output module)
W output module)
Version 3 power
system: 4730 W (4400
W output module)
Rated input
48 VDC nominal in North America
voltage per
60 VDC nominal in the European Community
power module (Range: 40.5 to 72 VDC [75 VDC for 5 ms])
Rated input
current draw
49 A maximum at 48 VDC nominal

39 A maximum at 60 VDC nominal
Source DC
service
requirement1
Sufficient to supply the rated input current. Local codes apply.
Redundancy
DC power modules
operate in N+1
redundancy mode2
At least two DC
power modules are
required for N+1
redundancy for a
fully configured
system
At least two DC DC power modules

power modules operate in N+1
are required for redundancy mode2
N+1 redundancy
for a fully
configured
system
DC power modules
operate in N+1
redundancy mode2
1. For each DC power supply module. Some power/chassis configurations may operate at lower current ratings than those specified in this table. Contact
your Cisco technical representative for more information.
2.
The number of DC power modules needed depends on the configuration of the chassis (e.g. number of line cards, RP cards, and FCs installed). Use the
Cisco Power Calculator (Cisco.com account required) at http://tools.cisco.com/cpc/launch.jsp to calculate how many AC power modules are needed.
A-6
Appendix A

AC Input Voltage Range
Table A-5
AC Input Voltage Range (Single-Phase Power Source)
Range
Minimum
Minimum
Nominal
Nominal
Maximum
Nominal
Maximum
Input Voltage
180 VAC
200 VAC
220 VAC
240 VAC
264 VAC
50 Hz
50/60 Hz
60 Hz
63 Hz
Line Frequency 47 Hz
DC Input Voltage Range

Table A-6
DC Input Voltage Range
Range
Minimum
Nominal
Maximum
Input Voltage
40 VDC
48 VDC
72 VDC
A-7
Appendix A

Table A-7
Parameter
Value
Voltage
Maximum
54.5 VDC
Nominal
54.0 VDC
Minimum
53.5 VDC
Power
Minimum (one power module)
1500 W
Maximum (three 2100 W power modules per tray x two

trays)
12,600 W (Cisco ASR 9010 Router only)1
Maximum (three 2100 W power modules in a single tray) 6300 W (Cisco ASR 9006 Router only)
1. Maximum output power the power system is capable of supporting (not system power consumption).

Table A-8
Parameter
Value
Voltage
Maximum
55.5 VDC
Nominal
54.0 VDC
Minimum
52.5 VDC
Power
2100 W
Maximum (four 2100 W DC power modules or 3000 W

AC power modules in a single tray)1
8400 W (DC) 12, 000 W (AC)

Cisco ASR 9006 Router and

AC power modules per tray x two trays)
16,800 W (DC) 24,000 W (AC)

(Cisco ASR 9010 Router only)

AC power modules per tray x four trays)
33,600 W (DC) 48,000 W (AC)

A-8
Appendix A

Table A-9
Parameter
Value
Voltage
Maximum
55.5 VDC
Nominal
54.0 VDC
Minimum
52.5 VDC
Power
4400 W
Maximum (four 4400 W DC power modules or three

6000 W AC power modules per tray x two trays)1
35,200 W (DC) 36,000 W (AC)

Maximum (four 4400 W power modules or three 6000 W 52,800 W (DC) 54,000 W (AC)
AC power modules per tray x three trays)
Maximum (four 4400 W power modules or three 6000 W 70,400 W (DC) 72,000 W (AC)
AC power modules per tray x four trays)

Table A-10
RSP/RP Port Specifications
Description
Value
Console port
EIA/TIA-232 RJ-45 interface, 9600 Baud, 8 data, no parity, 2 stop bits with
flow control none (default)
Auxiliary port
EIA/TIA-232 RJ-45 interface, 9600 Baud, 8 data, no parity, 1 stop bit with
software handshake (default)
Management ports (0, 1)
Dual-speed (100M/1000M) RJ-45
Sync ports (0, 1)
Can be configured as one of the following:
BITS (Building Integrated Timing System) port
J.211 or UTI (Universal Timing Interface) port
A-9
Appendix A
RSP Cards, RP Cards, and Fabric Card Power Consumption

Specifications
The following table lists the power consumption specifications for the RSP cards, RP cards, and fabric
cards. For power consumption values for the Ethernet line cards, see the Cisco ASR 9000 Series
Aggregation Services Router Ethernet Line Card Installation Guide.
Caution
Be sure that the chassis configuration complies with the required power budgets. Failure to properly
verify the configuration may result in an unpredictable state if one of the power units fails.
Table A-11
Card
Power Consumption
RSP Card
Power consumption
175 W at 77F (25C)

205 W at 104F (40C)
235 W at 131F (55C)
RSP-440 Card
Power consumption
285 W at 77F (25C)

350 W at 104F (40C)
370 W at 131F (55C)
RSP-440 Lite Card
Power consumption
240 W at 77F (25C)

270 W at 104F (40C)
300 W at 131F (55C)
RSP-880 Card
Power consumption
425 W at 81F (27C)

430 W at 104F (40C)
450 W at 131F (55C)
RP Card
Power consumption
227 W at 77F (25C)

251 W at 104F (40C)
259 W at 131F (55C)
RP2 Card
Power consumption
390 at 81F (27C)

400 at 104F (40C)
410 at 131F (55C)
FC Card (ASR 9922)
Power consumption
135 W at 77F (25C)

147 W at 104F (40C)
160 W at 131F (55C)
FC2 Card (ASR 9922)
A-10
Appendix A
Table A-11
RSP Cards, RP Cards, and Fabric Card Power Consumption Specifications (continued)
Card
Power Consumption
Power consumption
155 W at 81F (27C)

160 at 104F (40C)
165 at 131F (55C)
FC Card (ASR 9912)
Power consumption
80 W at 77F (25C)
82 W at 104F (40C)
88 W at 131F (55C)
FC2 Card (ASR 9912)
Power consumption
94 W at 81F (27C)
103 W at 104F (40C)
105 W at 131F (55C)
A-11
Appendix A

Note
The fan tray power consumption numbers reflect the power budget for a single fan tray
Table A-12
Description
Power Consumption
ASR 9010 Fan Tray V1
Power consumption
200 W at 77F (25C)

300 W at 104F (40C)
600 W at 131F (55C)
Power consumption
240 W at 77F (25C) |

960 W at 104F (40C)
1100 W at 131F (55C)
Power consumption
100 W at 77F (25C)

275 W at 104F (40C)
375 W at 131F (55C)
Power consumption
100 W at 77F (25C)

360 W at 104F (40C)
605 W at 131F (55C)
Power consumption
200 W at 77F (25C)

870 W at 104F (40C)
1000 W at 131F (55C)
Power consumption
290 W at 77F (25C)

900 W at 104F (40C)
1800 W at 131F (55C)
A-12
Appendix A
A-13
Appendix A
A-14
A P P E N D I X
Site Log
The site log provides a historical record of all actions relevant to the operation and maintenance of the
router. Keep your site log in a convenient place near the router where anyone who performs the
maintenance has access to it.
Site log entries might include the following:
Installation progressMake entries in the site log to record installation progress. Note any
difficulties and remedies during the installation process.
Upgrades or removal and replacement proceduresUse the site log as a record of router
maintenance and expansion history.
Each time a procedure is performed on the router, update the site log to show the following:
Any field replaceable unit (FRU) that is installed, removed, or replaced
Any router configuration changes
Software upgrades
Corrective or preventive maintenance procedures performed
Intermittent problems
Related comments
The following page shows a sample site log format. You can make copies of the sample or design your
own site log page to meet the needs of your site and equipment.
B-1
Appendix B
Date
Description of Action Performed or Symptoms Observed
B-2
Initials
Site Log

9000 Series

Uploaded by

Document Informationclick to expand document information9000

Document Informationclick to expand document information

Copyright:

Available Formats

9000 Series

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

9000 Series

Uploaded by

Copyright:

Available Formats

Cisco ASR 9000 Series

Aggregation Services Router

Cisco Systems, Inc.

Changes to This Document

Obtaining Additional Information and Support

Preparing for Installation

Safety Guidelines 1-1

Site Requirement Guidelines 1-8

AC Power Cord Illustrations (Version 2 and Version 3 Power) 1-43

Unpacking and Installing the Chassis

Pre-Installation Considerations and Requirements

Unpacking the Router 2-3

Removing Components Before Installing the Chassis 2-18

Removing Cards from the Chassis 2-23

Installing Chassis Accessories 2-61

Installing Cards and Modules in the Chassis

RSP Cable Management Ties 3-9

Connecting Cables to the RSP or RP 3-22

Connecting Power to the Router 3-26

Troubleshooting the Installation

Troubleshooting Overview 4-1

Troubleshooting the Power Subsystem 4-7

Monitoring Critical, Major, and Minor Alarm Status

Troubleshooting the Cooling Subsystem 4-32

Replacing Cisco ASR 9000 Series Router Components

Prerequisites and Preparation 5-1

Removing and Replacing the Fan Trays 5-11

Installing a Replacement Chassis in the Equipment Rack

Cisco ASR 9000 Series Routers Physical Descriptions

Cisco ASR 9000 Series Routers Environmental Specifications=

Cisco ASR 9000 Series Routers AC Electrical Specifications

Cisco ASR 9000 Series Routers DC Electrical Specifications

AC Input and DC Input Voltage Range

Power System DC Output Levels A-8

RSP Cards, RP Cards, and Fabric Card Power Consumption Specifications

Document Conventions, page 1

Related Documentation, page 2

Changes to This Document, page 2

Obtaining Additional Information and Support, page 3

Changes to This Document

Changes to This Document

Information added for Cisco ASR 9922 version 2 fan tray.

Information added about installing optional air baffles on the Cisco

Information added about the Cisco ASR 9912 Aggregation

Information added about the Cisco ASR 9000v satellite shelf

Updates and corrections made to various portions of the document.

Information added about the Cisco ASR 9000v satellite shelf

Changes to This Document (continued)

Information added about the new Cisco ASR 9000v (a satellite

Information added about the new RSP-440 Route Processor card,

Added power consumption specifications for the new 16-port

Updates and corrections made to various portions of the document.

Initial release of this document.

Obtaining Additional Information and Support

Preparing for Installation

Safety Guidelines, page 1-1

Site Requirement Guidelines, page 1-8

RSP and RP Port Connection Guidelines, page 1-55