What Is The Effect of A Notch

7. What is the effect of a notch or sawtooth on the leading edge of a wing?
What
are the advantages of these devices for high-speed military and commercial
aircraft?
Leading edge notches and dogtooths, a more common name for a sawtooth, are both
types of wing modifications. The two devices are also related to the vortex generator
and the leading edge root extension (LERX). Furthermore, a number of other
modifications produce similar effects, including the boundary layer fence and the
vortilon. Several of these wing devices are compared in the following diagram.
Wing aerodynamic devices that create vortices
The purpose of these modifications is to create vortices in a controlled and predictable

manner. Vortices are often undesirable because they produce drag, but the vortices
these devices create are beneficial since they delay wing stall. Stall occurs when a wing
reaches a high enough angle of attack that the airflow separates from its surface. This
flow separation results in a rapid loss of lift, and the aircraft may become uncontrollable.
The advantage of wing devices that create vortices is that a vortex adds energy to the
airflow and increases its forward momentum. This momentum encourages the airflow to
remain attached to the surface of the wing at higher angles of attack than it would
otherwise. As a result, the wing is able to continue generating lift in conditions where it
would have stalled. This behavior is particularly advantageous on high-performance
military aircraft that need to be extremely maneuverable at high angles of attack in
combat. The advantage for commercial airliners is increased safety since the plane is
less likely to experience a wing stall during critical stages of flight like takeoff and
landing.
Common vortex generator design
The method by which these vortex devices work can be better understood by studying
the above diagram of vortex generators on a wing. A vortex generator is much like a
miniature wing perpendicular to the main wing. These generators are mounted at an
angle of attack to the airflow over the wing so that each creates a vortex off the exposed
tip, much like a trailing vortex created by a wing. The above example shows vortex
generators aligned in opposite directions so that the vortices they create rotate opposite
to each other. These vortices serve to increase the speed of the downstream airflow so
that it is "entrained" to follow the sharp curvature of the deployed flap and remain
attached to its surface. Otherwise, the airflow would likely separate from the flap
causing a loss of lift.
A notched leading edge and a dogtooth work in a similar manner to increase the speed
of the flow over a portion of a wing and delay stall. The difference between all of these
various devices is the strength of the vortex each one generates, the conditions under
which the vortex forms, and the region of the wing affected by that vortex. Vortex
generators are typically used in a series to create a number of small vortices over a
large portion of wing. Leading edge root extensions produce a single strong vortex near
the wing root. A dogtooth also generates a single strong vortex and a notch usually
generates a pair of fairly strong vortices, one from each edge. However, a dogtooth or
notch is usually located toward the wingtip close to the aileron. This position helps
generate a high-speed airflow over the ailerons to increase their effectiveness and
improve maneuverability. Good examples of planes with dogtooths are the F-4 Phantom
II and F-18E/F Super Hornet.
Leading-edge dogtooths located near the ailerons on the F-18 Super Hornet
Related devices include the boundary layer fence and the vortilon. A fence is most often
used on a swept wing as a means of controlling spanwise flow. This type of flow occurs
when the air flowing over a wing moves outward towards the wingtip as it travels along
the wing. This motion is undesirable because it can often cause flow separation to occur
on the outer wing resulting in a loss of aileron control effectiveness. The purpose of a
fence is to redirect the flow aft towards the trailing edge. A further benefit of the fence is
that it can be used to create a vortex to increase the speed of the flow and delay
separation.
A vortilon serves the same purpose on the lower surface of a wing, and this device is
often referred to as an underwing fence for that reason. Like the traditional boundary
layer fence, the vortilon can also be used to create a vortex on the underside of the
wing at low angle of attack. The vortilon is far more useful at high angles, however,
when a second vortex travels around the leading edge and over the upper surface of
the wing. This vortex helps delay separation over the upper surface like those created
by the other surfaces we have explored. Underwing pylons can also generate the same
kind of vortex as a vortilon so long as the junction between the pylon and the wing is
located aft of the wing leading edge, as on the F-15E Eagle shown below.
F-15E wing pylon with vortilon characteristics
The majority of the wing modifications we have described are typically seen on military
aircraft, especially high-performance fighters. The leading edge extension, dogtooth,
and fences are particularly common on these planes since these devices increase the
stall angle of attack and improve maneuverability. These modifications are rarely seen
on commercial airliners where excellent maneuverability is unnecessary. However,
conventional vortex generators are quite common on airliners to increase the
effectiveness of flaps and other control surfaces during takeoff and landing.

What Is The Effect of A Notch

Uploaded by

Copyright:

Available Formats

What Is The Effect of A Notch

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

What Is The Effect of A Notch

Uploaded by

Copyright:

Available Formats

7. What is the effect of a notch or sawtooth on the leading edge of a wing?

Wing aerodynamic devices that create vortices

The purpose of these modifications is to create vortices in a controlled and predictable

Common vortex generator design

F-15E wing pylon with vortilon characteristics

You might also like