Scribd
Upload
228 views4 pages

Edwards Signaling EBPS6A Data Sheet

Buy the Edwards Signaling EBPS6A at JMAC Supply. https://www.jmac.com/Edwards_Signaling_EBPS6A_p/edwards-signaling-ebps6a.htm

Uploaded by

JMAC Supply
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
228 views4 pages

Edwards Signaling EBPS6A Data Sheet

Buy the Edwards Signaling EBPS6A at JMAC Supply. https://www.jmac.com/Edwards_Signaling_EBPS6A_p/edwards-signaling-ebps6a.htm

Uploaded by

JMAC Supply
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Edwards Signaling Catalog u Power Supplies and Accessories

Remote Booster
Power Supplies
EBPS6A, EBPS10A

MEA

476-91-E
Vol.13

Overview

Standard Features

The Booster Power Supply (EBPS) is a UL 864, 9th Edition listed


power supply. It is a 24 Vdc filtered-regulated, and supervised
unit that can easily be configured to provide additional notification
appliance circuits (NACs) or auxiliary power for Mass Notification/
Emergency Communication (MNEC), as well as life safety, security,
and access control applications.

Allows for reliable filtered and regulated power to be installed


where needed

Cost effective system expansion

Provides for Genesis and Enhanced Integrity notification appliance synchronization

Supports coded output operation

Self-restoring overcurrent protection

Multiple signal rates

Can be cascaded or controlled independently

Easy field configuration

On-board diagnostic LEDs identify wiring or internal faults

Standard Edwards keyed lockable steel cabinet with removable door

110 and 230 Vac models available

Accommodates 18 to 12 AWG wire sizes

Optional tamper switch

Dual battery charging rates

The EBPS contains the circuitry to monitor and charge internal


or external batteries. Its steel enclosure has room for up to two
10 ampere-hour batteries. For access control-only applications,
the EBPS can support batteries totaling up to 65 ampere-hours in
an external enclosure. The EBPS has four Class B (convertible to
two Class A) NACs. These can be activated in one or two groups
from the EBPSs unique dual input circuits.
The EBPS is available in 6.5 or 10 ampere models. Each output
circuit has a capacity of three amperes; total current draw cannot
exceed the units rating.
The EBPS meets current UL requirements and is listed under the
following standards:
Standard (CCN)
Description
UL864 9th ed.ition (UOXX)Fire Alarm Systems
UL636 (ANET, UEHX7)
Holdup Alarm Units and Systems
UL609 (AOTX, AOTX7)
Local Burglar Alarm Units and Systems
UL294 (ALVY, UEHX7)
Access Control Systems
UL365 (APAW, APAW7) Police Station Connected Burglar Alarm Units and Systems
UL1076 (APOU, APOU7) Proprietary Burglar Alarm System Units
UL1610 (AMCX)
Central Station Alarm Unit
ULC-S527 (UOXXC)
Control Units, Fire Alarm (Canada)
ULC-S303 (AOTX7)
Local Burglar Alarm Units and Systems (Canada)
C22.2 No. 205
Signaling Equipment (Canada)

Page 1 of 4

S85005-0125

D ATA S H E E T
Not to be used for installation purposes. Issue 5

Application

Dimensions

The EBPS provides additional power and circuits for notification


appliances and other 24 Vdc loads. It is listed for indoor dry locations and can easily be installed where needed.

D5

Fault conditions are indicated on the on-board diagnostic LEDs,


opening the EBPS input sense circuit and the trouble relay (if
programmed). While this provides indication to the host system,
the EBPS can still be activated upon command. A separate AC
Fail contact is available on the EBPS circuit board, which can be
programmed for trouble or AC Fail. There are seven on-board
diagnostic LEDs: one for each NAC fault, one for battery fault, one
for ground fault, and one for AC power.

EBPS NACs can be configured for a 3-3-3 temporal or continuous


output. California temporal rate outputs are also available on certain models. This makes the EBPS ideal for applications requiring
signaling rates that are not available from the main system.
In addition to the internally generated signal rates, the EBPS can
also be configured to follow the coded signal rate of the main
system NACs. This allows for the seamless expansion of existing
NACs.

D2

D3

Side View

D4

Front View

D1

D6

Side View

The unique dual-input activation circuits of the EBPS can be


activated by any voltage from 6 to 45 VDC (filtered-regulated) or
11 to 33 Vdc (full-wave rectified, unfiltered). The first input circuit
can be configured to activate 1-4 of the four possible outputs. The
second input circuit can be configured to control circuits 3 and 4.
When outputs are configured for auxiliary operation, these circuits
can be configured to stay on or automatically deactivate 30 seconds after AC power is lost. This feature makes these circuits ideal
for door holder applications. The EBPS also has a separate 200
mA 24 Vdc output that can be used to power internal activation
modules.

Top View

All knockouts
for 3/4 in conduit
(1.9 cm)

D1

D2

D3

D4

D5

D6

17.0 in
(43.2 cm)

3.5 in
(8.9 cm)

13.0 in
(33.0 cm)

6.5 in
(16.5 cm)

3.375 in
(8.6 cm)

12.0 in
(30.4 cm)

Wire routing

The EBPS enclosure has mounting brackets for up to three Signature modules to the right of the circuit board.

Engineering Specification
Supply, where needed, Edwards EBPS Series Booster Power
Supplies (EBPS) that are interconnected to and supervised by the
main system. The EBPS shall function as a stand-alone auxiliary
power supply with its own fully-supervised battery compliment.
The EBPS battery compliment shall be sized to match the requirements of the main system. The EBPS shall be capable of supervising and charging batteries having the capacity of 24 ampere-hours
for Mass Notification/Emergency Communication (MNEC), life
safety and security applications, and the capacity of 65 amperehours for access control applications.
The EBPS shall provide a minimum of four independent, fully supervised Class B circuits that can be field configurable for notification appliance circuits or auxiliary 24 Vdc power circuits. EBPS
NACs shall be convertible to a minimum of two Class A NACs.
Each EBPS output circuit shall be rated at 3 amperes at 24 Vdc.
Each output circuit shall be provided with automatically restoring
overcurrent protection. The EBPS shall be operable from the main
system NAC and/or Edwards Signature Series control modules.
EBPS NACs shall be configurable for continuous, 3-3-3 temporal
or optionally, California rate. Fault conditions on the EBPS shall
not impede operation of main system NAC. The EBPS shall be
provided with ground fault detection circuitry and a separate AC
fail relay.

Page 2 of 4

Notes
1. Maintain 1/4-inch (6 mm) spacing between power-limited and nonpower-limited
wiring or use type FPL, FPLR, or FPLP cable per NEC.
[2] Power-limited and supervised when not configured as auxiliary power. Nonsupervised when configured as auxiliary power.
[3] Source must be power-limited. Source determines supervision.
4. When using larger batteries, make sure to position the battery terminals towards
the door.

S85005-0125

D ATA S H E E T
Not to be used for installation purposes. Issue 5

Typical Wiring
Single or cascaded booster
anywhere on a notification appliance circuit

Fire Alarm
Control Panel

Sense 2 Input

Sense 1 Input

Existing NAC end-of-line resistors are not required to be


installed at the boosters terminals. This allows multiple
boosters to be driven from a single NAC circuit without the
need for special configurations.

To next signaling
device, booster, or
EOL resistor

NAC Circuit
NAC Circuit

NAC output #1
NAC output #2
NAC output #3
NAC output #4

Booster Power
Supply

Configuring the Booster for


AC Power Fail delay operation*

Multiple E-NAC modules using the


EBPSs sense inputs
Notification appliance circuit (NAC)

+
EOL 47 k

E-NAC Module

E-IDC1B
Module

Data in from previous + +


device or Signature
controller

Data in from
previous device
or loop controller

Data out to
next device

+ +

+
+

Notification appliance circuit (NAC)

UL listed
EOL 15 KOhm

IN
Sense 1 COM
OUT
IN
Sense 2 COM
OUT
NO
Trouble COM
NC

EOL 47 K

+
+

200 mA AUX
Continuous

UL listed
EOL 15 KOhm

UL listed
EOL 15 k Ohm

TB5

Notification appliance circuit (NAC)

IN
Sense 1 COM
OUT
IN
Sense 2 COM
OUT
NO
Trouble COM
NC

Page 3 of 4

NAC1/
AUX1
NAC2/
AUX2
NAC3/
AUX3
NAC4/
AUX4

UL listed
EOL 15 k Ohm

+
TB5

NAC1/
AUX1
NAC2/
AUX2
NAC3/
AUX3
NAC4/
AUX4
200 mA AUX
Continuous

Notification appliance circuit (NAC)

EOL 47 K

E-NAC Module

E-NAC Module

Data out to
next device
+

*The Booster supports AC Power fail delay


of three hours via its trouble contact when
dip switch SW2-6 is on. All other troubles
are reported to supervising module or panel
without delay via Sense inputs.

S85005-0125

D ATA S H E E T
Not to be used for installation purposes. Issue 5

Specifications
Model
AC Line Voltage
Contact us...
Phone: 1-800-336-4206
Web: www.edwardssignaling.com
Edwards Signaling is
an EDWARDS brand.
3 Farm Glen Boulevard
Farmington, CT 06032
In Canada, contact Chubb Edwards...
Email: [email protected]
Web: www.chubbedwards.com
2013 UTC Fire & Security Americas
Corporation, Inc. All rights reserved.
Specifications subject to change
without notice. Edwards is part of UTC
Climate, Controls & Security, a unit of
United Technologies Corporation.

Notification Appliance
Circuit Ratings
Trouble Relay
Auxiliary Outputs
Input Current
(from an existing NAC)
Booster Internal
Supervisory Current
Booster Internal Alarm
Current
Signature Mounting
Space
Maximum Battery Size

Terminal Wire Gauge


Relative Humidity
Temperature Rating
NAC Wiring Styles
Output Signal Rates
Ground Fault Detection
Agency Listings
1.
2.

6.5 amp Booster


10 amp Booster
120VAC or 220-240VAC 50/60Hz 120VAC or 220-240VAC 50/60Hz
580 watts
390 watts
3.0A max. per circuit @ 24Vdc
3.0A max. per circuit @ 24Vdc
nominal 10A max total all NACs
nominal 6.5A max total all NACs
2 Amps @ 30Vdc
Four configurable outputs replace NACs 1, 2, 3 or 4. as auxiliary
outputs and 200 mA dedicated auxiliary. (See note 2.)
3mA @ 12Vdc, 6mA @ 24Vdc
70mA + 35 mA for each circuit set to AUX
270mA
Accomodates three two-gang modules.
10 Amp Hours (2 of 12V10A) in cabinet up to 24 Amp hours with external battery cabinet for fire and security applications; up to 65 Amp
hours for access control applications in external battery box.
18-12 AWG
0 to 93% non condensing @ 32C
32 to 120F (0 to 49C)
Class A or Class B
Continuous, California rate, 3-3-3 temporal,
or follow installed panels NAC. (See note 1.)
Enable or Disable via jumper
UL, ULC, CSFM

Model EBPS*CAA provides selection for California rate, in place of temporal.


Maximum of 8 Amps can be used for auxiliary output.

Ordering Information
Catalog
Number
EBPS6A
EBPS10A

Description

Shipping
Wt. lb (kg)
13 ( 5.9)
13 ( 5.9)

6.5 Amp Booster Power Supply


10 Amp Booster Power Supply

Related Equipment
12V6A5
7.2 Amp Hour Battery, two required
12V10A
10 Amp Hour Battery, two required
BC-1
Battery Cabinet (up to 2 - 40 Amp Hour Batteries)
BC-2
Battery Cabinet (up to 2 - 17 Amp Hour Batteries)
12V17A
18 Amp Hour Battery, two required (see note 1)
12V24A
24 Amp Hour Battery, two required (see note 1)
12V40A
40 Amp Hour Battery, two required (see notes 1, 2)
12V50A
50 Amp Hour Battery, two required (see notes 1, 2)
12V65A
65 Amp Hour Battery, two required (see notes 1, 2)
1.
2.

Requires installation of separate battery cabinet.


EBPS supports batteries greater than 24 Amp hours for access control applications only.

S85005-0125

D ATA S H E E T
Not to be used for installation purposes. Issue 5

06-27-13

Page 4 of 4

3.4 (1.6)
9.5 (4.3)
58 (26.4)
19 (8.6)
13 ( 5.9)
20 (9.07)
32 (14.5)
40 (18.14)
49 (22.2)

You might also like