Scribd
Upload
374 views2 pages

Biochrom Anthos 2020 Microplate Reader Quick Start Guide - 2020-QSG-Formated

The document provides instructions for performing a quick single point measurement using the BIOCHROM ANTHOS 2020 MICROPLATE READER. Key steps include: (1) Turning on the instrument and selecting "Quick" from the main menu or using the F1 key; (2) Choosing "Single Pt" and selecting the measurement and reference filters; (3) Initiating the measurement using the F5 key. The final data will appear after both readings are taken and can be printed.

Uploaded by

luroguita
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
374 views2 pages

Biochrom Anthos 2020 Microplate Reader Quick Start Guide - 2020-QSG-Formated

The document provides instructions for performing a quick single point measurement using the BIOCHROM ANTHOS 2020 MICROPLATE READER. Key steps include: (1) Turning on the instrument and selecting "Quick" from the main menu or using the F1 key; (2) Choosing "Single Pt" and selecting the measurement and reference filters; (3) Initiating the measurement using the F5 key. The final data will appear after both readings are taken and can be printed.

Uploaded by

luroguita
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

BIOCHROM ANTHOS 2020 MICROPLATE READER

QUICK START GUIDE

1. Connect instrument to a power source using the appropriate power cord. Turn on the instrument.
Check users manual for important safety information.
2. Upon start up, the main menu will appear on the screen:
Figure 1. Anthos 2020 Display and Main Menu
To select options in the menu bar in the upper left
corner, select menu and then the arrow keys to move
the cursor to your selection. Select enter to access the
option. Select stop to go back. The options at the
bottom of the screen can be accessed using the function
key below the desired option.

Function keys (F1 F5, from left to right)


Arrow keys
Menu key
Enter key
Stop key
Table 1 Anthos 2020 Keys and Functions
Keypad
Options

Function

Function Key
Options

Function

<stop>

Aborts the current task including during a


measurement
Cancels dialogues boxes
Aborts remote mode

QUICK (F1)

Starts a quick measurement without test


programming

<prev>

Returns the user to the previous dialogue


element

RUN-TEST (F2)

Starts a pre-programmed test

<enter>

Confirms the text or numerical entry and


leads the user to the next dialogue element

INIT (F4)

Performs an initialization of the instrument

<ce>

Changes and edits existing values


Activates the text and/or formula input menu
Opens printer drop down menu in Setup

SHUTDOWN
(F5)

Prepares the instrument to be turned off

<display>

Changes the contrast of the display

September 2010

Anthos 2020 Quick Start Guide

Version 1.0

3. Before reading a plate, determine the location of the data export. Measurements can be saved
on the instrument or printed. To connect the instrument to a printer, select menu>setup>enter
on the keypad. See the users manual for compatible printers. Quick measurements are not
saved on the instrument.
Note: a test definition is required to save plate measurement results on the
instrument.
4. To perform a quick single point measurement, select Quick using the F1 key or in the menu bar.

Figure 2 Quick Measurement Screen

5. Two options will appear on the display: Single Pt and Kinetic. For simple endpoint
measurements. Select Single Pt using the F1 key.
6. Next, select the measurement filter by highlighting the filter using the arrow keys. Once the
desired wavelength is selected, press enter to select a reference filter.
Note: A reference reading is recommended to account for optical interference that
may result from the plate. For reference reading, select a wavelength that the
sample of interest does not absorb.
6. Initiate the measurement by selecting the F5 key, Start Meas. The measurements will start after
initiation of the light source.
7. The readings will appear on the screen in real-time. The final data (measurement data
reference data = final data) will appear on the display after both the measurement and
reference readings have occurred. To display the raw data on the screen, select F3 and F4 to
scroll between the three screens (measurement data, reference data and final data).
8. Select F5 to Print. To include raw data in the printout, select Yes>Enter when prompted.

September 2010

Anthos 2020 Quick Start Guide

Version 1.0

You might also like