Scribd Logo
Upload

Welcome to Scribd!

  • 221 views

    Procedures For Connecting Switchgear and PSA

    Uploaded by

    Sandy Franks
    This document provides tie-in procedures for connecting switchgear and a PSA panel for a substation project in Riyadh, Saudi Arabia. It outlines steps to modify existing switchgear to accommodate new selector switches and control schemes, run cables between the switchgear and PSA panel, configure I/O and check functionality. Key steps include replacing selector switches per drawings, running status and control cables, modifying schemes, checking I/O functionality via HMI, and testing breaker operation in local, remote, PSA and SCADA modes. The goal is to integrate the switchgear with the PSA panel based on approved drawings and I/O lists.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Procedures For Connecting Switchgear and PSA

    Uploaded by

    Sandy Franks
    221 views3 pages
    This document provides tie-in procedures for connecting switchgear and a PSA panel for a substation project in Riyadh, Saudi Arabia. It outlines steps to modify existing switchgear to accommodate new selector switches and control schemes, run cables between the switchgear and PSA panel, configure I/O and check functionality. Key steps include replacing selector switches per drawings, running status and control cables, modifying schemes, checking I/O functionality via HMI, and testing breaker operation in local, remote, PSA and SCADA modes. The goal is to integrate the switchgear with the PSA panel based on approved drawings and I/O lists.

    Original Title

    Procedures for Connecting Switchgear and PSA.docx

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides tie-in procedures for connecting switchgear and a PSA panel for a substation project in Riyadh, Saudi Arabia. It outlines steps to modify existing switchgear to accommodate new selector switches and control schemes, run cables between the switchgear and PSA panel, configure I/O and check functionality. Key steps include replacing selector switches per drawings, running status and control cables, modifying schemes, checking I/O functionality via HMI, and testing breaker operation in local, remote, PSA and SCADA modes. The goal is to integrate the switchgear with the PSA panel based on approved drawings and I/O lists.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    221 views3 pages

    Procedures For Connecting Switchgear and PSA

    Uploaded by

    Sandy Franks
    This document provides tie-in procedures for connecting switchgear and a PSA panel for a substation project in Riyadh, Saudi Arabia. It outlines steps to modify existing switchgear to accommodate new selector switches and control schemes, run cables between the switchgear and PSA panel, configure I/O and check functionality. Key steps include replacing selector switches per drawings, running status and control cables, modifying schemes, checking I/O functionality via HMI, and testing breaker operation in local, remote, PSA and SCADA modes. The goal is to integrate the switchgear with the PSA panel based on approved drawings and I/O lists.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 3

    Procedures for Connecting

    Switchgear and PSA


    Tie In Procedures
    Dated: 08th April 2014
    Document No TIP-Sub-R1A-Rev00
    PO No 6510521318
    Client Saudi Electricity
    Job Order No 7-00014
    Project Name Installation of HMI at 7 substations in Riyadh
    Plant RIyadh Sub R1A
    Tie In Procedures for Transformer Feeders GCB3A, GCB2A, GCB3B, GCB2B, Tie
    Breaker and Incomer-1 and Incomer-2
    Reference Documents
    1. IO List
    V21-R1A-IO-STATUS-001 Rev 01, V21-R1A-IO-CONTROL-001 Rev 01
    2. Approved Red Marked Schematics for the Switchgear
    3. PML Meter Daisy Chain Drawing V21-R1A-DS-001 Rev01

    Make sure the Breaker Transformer Feeder is in Open Condition


    Make sure both the disconnect Switches are open and both the
    Grounding Switches are closed to put the breaker under modification
    under test position (tags to be discussed with POD/ESO engineers
    before operation)
    Open the MCB for Closing Circuit and Tripping Circuit on the Switchgear
    Side and Tag it
    Open the MCB DC-1 and AC-1 and AC-Aux inside V21-R1A-PSA-001 and
    Tag it
    Existing Selector Switch will be replaced with the new Selector Switch
    using the following steps
    o Tag each and every wire of the existing selector switch
    properly for Local/Remote contacts and verify from the
    drawings.
    o Open the control cables from the existing selector switch and
    pull out the existing selector switch from the switchgear
    panel, install the new selector switch and carefully following
    the approved RED MARKED modified drawings for the panel,
    put back the Local and Remote contacts to the new selector
    Switch on the same positions of Local and Remote matching
    each other.
    o New Selector Switch will be used on the same location and
    same cut-out as the original.
    Saudi Aramco: Company General Use

    o One Extra Contact (apart from the contact being used in the
    scheme) from Local and Remote shall be taken to the
    Terminal Block as per the RED MAREKD Modified drawings for
    the switchgear.
    o One Contact from PSA and SCADA each shall be wired to the
    terminal block as per RED MARKED Modified drawings.
    Install new Terminal Block Strip along with all accessories i.e. CChannel, Tag Carrier, Protective Strip and Terminal Numbering, End
    Plates and End Stoppers
    Local / Remote / PSA and SCADA and Breaker Open / Close Status
    Signals shall be taken to the designated Terminal Block No referring to
    Approved Red Marked Drawings
    25Core 22AWG Status Cable shall be used to carry these signals from
    the terminal blocks installed inside the switchgear to the terminal
    blocks inside the PSA Panels consulting the IO List and Approved Red
    Marked Modified Drawings
    Modify the existing switchgear scheme to accommodate and segregate
    Local, Remote, PSA and SCADA positions in Close and Trip Circuit using
    Approved Red Marked Modified Drawings
    14Core 14AWG Cable shall be used to run the control signals from
    terminal blocks of the switchgear to the terminal blocks of the PSA
    panel consulting the IO List and Approved Red Marked Modified
    Drawings
    PML meters shall be daisy chained as per the Daisy Chain Approved
    Connection Diagram and signals brought to PSA Panel V21-R1A-PSA002 via 22AWG 3 Core Wire.
    Lock Out Relay Connection and 94 Operated Connection of the
    respective Feeders shall be wired to the Digital Input of the PML Meter
    as per the IO List
    Perform Continuity Test / Loop Check for the modified circuit from
    Switchgear to PSA panel and highlight in as-builts
    With the breaker still in test mode (i.e. Disconnector open and
    Grounding closed), turn on the MCB for Tripping and Closing Circuit.
    Turn on the MCB DC-1 and AC-1, AC-Aux inside the PSA Panel and
    power on the IO Controllers DPAC-1 and DPAC-2
    Using the IO list, check the status of Direct / Remote / PSA / SCADA
    selector switch.
    Each position of Selector Switch should light up its respective LED (IO
    List to be used as reference) and Digital Input which will be viewed
    from HMI
    Check the Lock Out Relay Operation and check the status on PSA Panel
    from HMI by jumping the contact of the Lock Out Relay. Special
    Cautious measures to be taken that Lock Out Relay should not trigger
    any other Breaker

    Saudi Aramco: Company General Use

    Opening and Closing of Circuit Breaker while still in test mode (i.e.
    Disconnector open and Grounding closed) via Local, Remote, PSA and
    SCADA
    Do the testing of opening and closing against the positions as per the
    reaction matrix below

    Saudi Aramco: Company General Use

    You might also like