Scribd
Upload
209 views

Assignment

This document contains answers to 5 questions about machining processes. Question 1 explains that specific energies are higher in grinding than machining due to wear flats causing high friction, large negative rake angles requiring plastic deformation of chips, and smaller chips in grinding creating more surface area for friction. Question 2 calculates chip dimensions for a surface grinding operation. Question 3 compares temperature rises between two grinding operations. Question 4 outlines the main advantages of electrical discharge machining (EDM) and when it can be used. Question 5 states that EDM and laser cutting can cause thermal damage through heat, leading to a heat affected zone and potential fatigue failure.

Uploaded by

Utkarsh Shrivatava
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
209 views

Assignment

This document contains answers to 5 questions about machining processes. Question 1 explains that specific energies are higher in grinding than machining due to wear flats causing high friction, large negative rake angles requiring plastic deformation of chips, and smaller chips in grinding creating more surface area for friction. Question 2 calculates chip dimensions for a surface grinding operation. Question 3 compares temperature rises between two grinding operations. Question 4 outlines the main advantages of electrical discharge machining (EDM) and when it can be used. Question 5 states that EDM and laser cutting can cause thermal damage through heat, leading to a heat affected zone and potential fatigue failure.

Uploaded by

Utkarsh Shrivatava
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

ASSIGMENT NO.

: 5
Q1. Explain the reasons for the large difference between the specific energies involved in machining when
compared to grinding?
Answer: Specific energies in grinding as compared to machining are much higher because:

Due to the presence of wear flats (causing high friction)

Due to the large negative rake angles (typically found in abrasives) and hence, the chips formed during
grinding must undergo plastic deformation, and therefore require more energy

The chips produced during grinding are small in comparison to machining. Therefore, there is more
surface area for frictional losses per volume of material removed when compared with machining

Rubbing of grains or portion of non-active grains may also be a contributing factor


Q2. Calculate the chip dimensions for the following surface grinding operation: Wheel diameter, 10 in.; Depth
of cut, 0.001 in.; Work feed, 125 ft/min.; Spindle rpm, 3000 rpm; Higher than average abrasive density.
Answer:
Wheel diameter (D) = 10 inch
Depth of cut (d) = 0.001 inch
Work feed (v) = 125 ft/min = 1500 inch/min
Spindle rpm (N) = 3000 rpm
Tangential Velocity (V) = DN = 3.14X10X3000 = 94248 inch/min
Contact Length = Chip Length (l) = (DXd)1/2 = (10X0.001)1/2 = 0.1 inch
As the abrasive density is higher than the average, therefore
C = 750/inch2
(100/inch2 C1000/inch2)
and r = 15
(10 r20)
Grain depth of cut = Chip Thickness (t) = ((4v/VCr) X (d/D)1/2)1/2 = 2.38 X 10-4 inch
Q3. Assume that a surface grinding operation is being carried out using the following conditions: D = 200mm, d
= 0.1 mm, v = 40 m/min, and V = 2000 m/min. These conditions are then changed to the following D=150 mm,
d = 0.1 mm, v = 30 m/min, and V = 2500 m/min. How different is the temperature rise from the rise that occurs
with the initial conditions?
Answer: The temperature difference on the surface due to grinding is given by,
T = D1/4 X d3/4 X (V/v)1/2
Therefore,
T1 = (200)1/4 X (0.1)3/4 X (2000/40)1/2 = 3.76X0.178X7.07 = 4.73 T (approximately)
T2 = (150)1/4 X (0.1)3/4 X (2500/30)1/2 = 3.49X0.178X9.13 = 5.7 T (approximately)
Difference = T2 T1 = 5.7 4.73 = 0.97
T2 > T1 due to the substantially larger value of (V/v) 1/2 in the second case, as compared to the first case.
Q4. What are the main advantages of electrical discharge machining and where would you utilize the process?
Answer: The main advantages of electro-discharge machining (EDM) are:
It can create very complex forms in extremely hard material with fine surface finishes
It can even be used to disintegrate broken tools
It can machine parts that are very thin or fragile as no force is imparted onto the work piece

This process can be utilized where:

Complex shapes that would otherwise be difficult to produce with conventional cutting tools

Very small work pieces where conventional cutting tools may damage the part from excess cutting tool
pressure

There is no direct contact between tool and work piece and therefore delicate sections and weak
materials can be machined without any distortion
Q5: Which of the advanced machining processes would cause thermal damage? What is the consequence of
such damage to the work piece?
Answer: The advanced machining processes which cause thermal damage are those that involve high levels of
heat, which are: EDM and laser cutting.
The thermal effects of these machining processes lead to the development of Heat Affected Zone (HAZ) on the
work piece, which affect the hardness and ductility of the work pieces material. Moreover, it can also lead to
fatigue failure due to the development of small cracks caused by the modification in internal stresses.

You might also like