NEC Confidential

iPASOLINK ETH FUNCTION SETTING

- Ethernet Port Setting
- Vlan Setting
- Ethernet OAM Setting
- Quality Of Service

ETHER FUNCTION SETTING

Page 2

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting ETH Port Setting (1 of 2)

Expand Provisioning from LCT menu.

Expand ETH Function Setting from Provisioning sub menu.
Select ETH Port Setting from ETH Function Setting sub menu
Current ETH Port setting and port link status are displayed.
Click the main Board Port # to open its ETH Port Setting window
Select the Port Usage enable radio button to use the selected port
Set the other settings accordingly and click the OK button

Page 3

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting ETH Port Setting (2 of 2)

Port Usage Enable or disable the port (by default it is enabled)
Port Name Any user friendly port name can be used (maximum 32
characters)
Media Type Electrical (RJ 45) or Optical (SFP) (by default it is electrical)
Speed Choose among 10 Mbps, 100 Mbps, 1000 Mbps, Auto
Negotiation (by default it is Auto Negotiation)
When speed is chosen to be auto negotiated, duplex mode as well as
MDI/MDIX will also be auto negotiated
Duplex Mode Full Duplex or Half Duplex (by default it is Full)
MDI or MDIX Medium Dependent Interface or Medium Dependent Interface
Crossover (by default it is MDI)
MDI ports connect to MDIX ports via straight-through twisted pair cabling; both
MDI-to-MDI and MDIX-to-MDIX connections use crossover twisted pair
cabling, Auto MDI / MDIX removes these restriction on choosing cable type

Flow Control Enable or Disable Ethernet Flow Control (by default it is disabled)
When sending station transmits data faster than the receiving station can
accept it. The overwhelmed network element will send a PAUSE frame, which
halts the transmission of the sender for a specified period of time

Page 4

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting VLAN Setting (1 of 4)

Expand Provisioning from LCT menu.

Expand ETH Function Setting from Provisioning sub menu.
Select VLAN Setting from ETH Function Setting sub menu
Current VLAN settings are displayed.
Click on VLAN Setting tab to see the current VLAN setting
Click on VLAN List tab to see the current VLAN List

Page 5

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting VLAN Setting (2 of 4)

Click Add VLAN ID to open the Add

VLAN ID window
Enter the VLAN ID
Enter a VLAN Service Name for the
VLAN ID
Click OK button to close the window

Click Delete VLAN ID to open the Delete

VLAN ID window
Enter the VLAN ID or its VLAN Service
Name to be deleted from the VLAN List
Click OK button to close the delete VLAN
ID window
Click the VLAN Service Name to be
modified from the VLAN List

Item
VLAN ID
VALN
Service
Name
Page 6

Parameter
1 to 4094
1 to 32
Character

Description
Specify
VLAN ID
Specify the
service
name of the
VLAN

PT. NEC Indonesia 2010

Modify the VLAN Service Name

Click OK button to close the Modify VLAN
Service Name window
Confirm the VLAN Service Name is change
din the VLAN List

NEC Confidential

Confirm the VLAN ID is deleted from the

list

ETH Function Setting VLAN Setting (3 of 4)

Click the Port to which the VLAN ID is to

be assigned.
Port /VLAN Configuration is displayed
Select the Port Type under VLAN Assignment
Port Type Access / Truck / Tunnel
Modem Port is always Trunk Port type
Main Board Ports can be Access, Tunnel and
Trunk Port types

Item

Parameter

Description

Port Type

Access

Only Allow untagged frame pass through

Tunnel

Allow tagged and untagged frame pass through

Select the VLAN ID (s) for the Selected Port

and Port Type by selecting the enable check
boxes

Trunk

Only allow tagged frame pass through

Enable check box

Check

Check the box to assign the port to the specified

Uncheck

VLAN.

Page 7

PT. NEC Indonesia 2010

Untag Frame Assignment (Access

Check

Port)

Uncheck
NEC Confidential

ETH Function Setting VLAN Setting (4 of 4)

Page 8

PT. NEC Indonesia 2010

NEC Confidential

Example of Modem Port

Modem port is always Trunk
(tagged frames only)

Modem port transports the VLAN IDs enabled

here. In this example, only tagged frames
belonging to VLAN ID =, 10, 20 , 30, 40 qnd 50
are processed on this Modem1 port.

Page 9

PT. NEC Indonesia 2010

NEC Confidential

Example of Access Port (Untagged Frames only)

Only Untagged frames are

processed on Port 3, and
these frames are assumed
to belong to VLAN ID = 30

Fm to VLAN MSG
A
B 30
Fm
A

to
B

MSG

P1 (FE)
Fm to VLAN MSG
A
C x

Page 10

PT. NEC Indonesia 2010

NEC Confidential

Example of Trunk Port (tag/untag Frames)

Tagged frames on
Port 1 must have
VLAN ID = 10 & 30

Fm to VLAN MSG
A
B 20
Fm
A

to
B

MSG

Fm to VLAN MSG
A
C 30

Fm to VLAN MSG
A
C 30

P2 (FE)
Fm to VLAN MSG
A
C other

Page 11

PT. NEC Indonesia 2010

NEC Confidential

Untagged frames on
Port 1 are assumed to
belong to VLAN ID = 20

Example of Tunnel Port (Any Frame Forwarding)

Any frame type on Port 3, either

untagged or tagged with any VLAN
ID, will be unconditionally tagged
(Outer Tag) with VLAN ID = 30 and
then processed.

Fm to VLAN MSG
A
B 30
Fm
A

to
B

MSG

Fm to VLAN VLAN MSG1

any
A
C 30

Fm to VLAN MSG1
A
C any

P3 (FE)

Page 12

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting ETH OAM (1 of 4)

Ethernet OAM (Operations, Administration, and Maintenance)

Maintenance End Point

Maintenance Intermediate Point

Maintenance Entity Group

Expand Provisioning from LCT menu.

Expand ETH Function Setting from Provisioning sub menu.
Select ETH OAM Setting from ETH Function Setting sub menu
Select OAM MEP tab to see the current MEP Index entries
Select OAM MIP tab to see the current MIP entries
Select OAM MEG tab to see the current MEG entries

Page 13

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting ETH OAM (2 of 4)

MEP Index Index (Serial) No. of the MEP

1 to 192
MEP ID Unique ID of MEP 1 to 8191
CCM Transmit / Receive Enable or
disable CCM (Continuity Check Messages)
transmit and/or receive
CCM Priority - Set priority for CCM 0 to 7
VLAN Untag Choose if VLAN tag to be
used with Ethernet OAM messages or not
Item Choose among Main Board /
Modem1 / 2
Port Choose the port number
ETH OAM Source MAC Address Specify
the MAC address to be used as source MAC
address of Ethernet OAM messages

Page 14

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting ETH OAM (3 of 4)

MEG Configuration - Maintenance Entity Group (Add / Delete)

Enable enables an MEG
MEG Index Serial Number of MEG (1 to 5)
MEG ID Unique ID for MEG
MEG Level hierarchy level of MEG (0 to 7)
ETH-CC Period Ethernet Continuity Check Message Period in ms or s
Peer MEP Configuration
Enable
Peer MEP ID (1 to 8191)
Peer List Check Status Enabled

Page 15

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting ETH OAM (4 of 4)

MIP (Maintenance Intermediate Point)

Settings Add / Modify / Delete

MIP Index 1 to 32
MEG Level 0 to 7
Item Main Board / Model 1 / 2
Port Port No.
Enable Enable or disable
VLAN ID VLAN ID to be used
Service Name VLAN Service Name

Page 16

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting RSTP Setting (1 of 2)

Item
STP Mode

Enable
Item

Port
Port Name
Path Cost

Path Cost
Value
Port
Priority
Edge
P-to-P

Page 17

PT. NEC Indonesia 2010

NEC Confidential

Parameter
RSTP
Disable
Check
Uncheck
Main Board
MODEM 1
MODEM 2
1 to 32
Character
Auto

Description
Enable RSTP (Rapid Spanning Tree
Protocol)
Disable RSTP
Enable RSTP on the port.
Disable RSTP on the port.
Select the object from drop-down list

Select the port from drop-down list

Specify the port name

Manual
1 to
200000000
0 to 240

Enable equipment calculate the path

cost automatically.
Enter the path cost manually.
Enter the cost of path when Path
Cost is set to Manual
Specify the RSTP priority of the port

Enable
Disable
Force true
Force False
Auto

Set the Port as Edge port

Remove Edge port feature
Enable Point-to-point
Disable Point-to-point
Set Point-to-point automatically

ETH Function Setting RSTP Setting (2 of 2)

Item
STP Bridge Priority
STP Bridge MAX
Age

Paramet
er
0 to
61440
6 to 40 s

Description
Set STP priority of the bridge

Set the expiration of the Configuration

BPDU stored, Bridge will. notice that a
topology change has occurred after the
Max Age time elapses and the BPDU is
aged out
1s
STP Bridge Hello
Set the period of sending Configuration
Time
2s
BPDUs from Root Bridge.
4 to 30 s Set the delay when the port is going to
STP Bridge
Forward Delay
change the state from Listening to
Learning.
1
to
10
STP
Set the number of BPDUNEC
which
can be
Confidential
PageTX
18 Hold PT. NEC Indonesia 2010
Count
sent per second

QUALITY OF SERVICE SETTING

Page 19

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting QoS/Classification (1

of 7)

Classify Field Type

VLAN CoS 802.1 q / p
IPv4 Precedence

Classify Priority used to classify

Classify Internal Priority

Page 20

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting QoS/Classification (2

of 7)

Page 21

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting QoS/Classification (3

of 7)
Classify Setting tab
iPASOLINK supports QoS based on MEF10 and REC4115 which classify the traffic into eight classes with the proper
Internal Priority according to the predetermined Policer. Except the default Policer, user can configure up to three
additional Policer which provide user the capability of realizing the user-orientation QoS strategy flexibly. The
Internal Priority is used for following purpose:
1) Identify Ingress traffic properly according to the predetermined Policer.
2) Mapping the eight classes of ingress traffic to four classes when queuing the Egress traffic
3) Copy the original internal priority to the capsulated frame to prevent the traffic priority from changing unexpectedly. (VLAN c-tag
CoS/VLAN s-tag CoS)
Ingress
At the Ingress of the traffic, assign the internal priority and then perform flow control according to the predetermined policer,
coloring the frame with Yellow or Green which decide the QoS queue at the egress, discarding the frames of the traffic that
exceed the designated bandwidth (EIR, Excess Information Rate).
Egress
Queuing the frame according to the internal priority and the color assigned at ingress, determine forwarding or discarding
the frame.

Page 22

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting QoS/Classification (4

of 7)
Item
Parameter
QoS Port Setting Information
Scheduling Mode
2xSP
4xSP
1xSP+3xDWRR
4xDWRR
Port Drop Mode
WTD

WRED

Egress Shaper Rate

0 to 1000 Mbps

Description
Specify the queuing mode.
SP: Strict-Priority
DWRR: Deficit Weighted Round Robin
Specify the port discard all packets at the tail end of the
queue when queue exceeded the pre set threshold. WTD
(Weighted tail drop).
Specify the port randomly discard the packets of lower
priority traffic before higher priority traffic when queue
exceeded the preset threshold. WRED (weighted random
early detection).
Specify the maximum sending rate of the egress queue.

Internal Priority Queuing Policy per Ingress Port

0 to 7
Set the priority of Ingress port
Internal Priority 0 to 7
Class
Egress Class Setting Information
Class Shaper Rate
0 to 1000 Mbps
Specify the maximum sending rate of the class.

Page 23

Class DWRR Weight

1 to 127

Specify the weight of the queue.

Class Queue Length

16 to 128 Kbyte

Wtd Yellow Frame

Threshold

10 to 100 %

Specify the length for each Queue.

Queue 6 and 7 is fixed at 16Kbyte.
Set the Threshold of Yellow Frame

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting QoS/Classification (5

of 7)

Page 24

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting QoS/Classification (6

of 7)

Page 25

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting QoS/Classification (7

of 7)

Page 26

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting QoS/Classification (7

of 7)

Page 27

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting QoS/Classification (7

of 7)

Page 28

PT. NEC Indonesia 2010

NEC Confidential

ETH Function Setting QoS/Classification (7

of 7)

Page 29

PT. NEC Indonesia 2010

NEC Confidential

Provisioning LLF Setting

Page 30

PT. NEC Indonesia 2010

NEC Confidential

Thank you
This training document describes the current version of the equipment.
The specifications or configuration contained in this document are subject to change
without notice.

Page 31

PT. NEC Indonesia 2010

NEC Confidential